Development of csharp based computer program for the design of single

Civil and Environmental Research www.iiste.org
ISSN 2224-5790 (Paper) ISSN 2225-0514 (Online)
Vol.6, No.8, 2014
Development of Csharp-Based Computer Program for the Design
of Single Storey Fixed-Feet Pitched-Roof Portal Frame
Chinwuba Arum1* Oladimeji Benedict Olalusi1
1Department of Civil Engineering, School of Engineering and Engineering Technology,
The Federal University of Technology, Akure
*E-mail of the corresponding author: arumcnwchrist@yahoo.co.uk
Abstract
This paper presents the design results of a simple task-specific Csharp-based computer program developed for
the design of single storey fixed-feet pitched-roof portal frame. The program accommodates varying
stanchion/rafter lengths and loadings. The overall process in the development of the program includes:
formulation of the portal frame design outline, coding the outline into computer algorithm using Csharp
programming language, implementing the developed program, development of the graphical user interface,
testing the developed program and validation of results. Several sets of steel pitched-roof portal frame models
were designed using the developed program and the design results were validated using established software -
MasterSeries. Those frames were varied in span, slope angle and frame spacing. The design results obtained
using the developed Csharp program were similar to the results obtained using standard software – MasterSeries,
with greatest variation in the values standing at a mere 0.8%. Furthermore, the developed program was used to
establish the relationships between span, slope angle, frame spacing and mass of framework steel of a single
storey, fixed-feet pitched-roof portal sample frame building.
Keywords; fixed-feet pitched-roof portal frame, code, Csharp
1. Introduction
1.1 General Overview
The use of steel framed structures for large industrial buildings permits the creation of buildings with large and
uninterrupted span areas, with the advantage of low cost, light weight and easy installation (Vasanthakumar,
2013). Steel portal frame is the dominant form of structure for single-storey industrial and commercial buildings.
It has become the most common structural form in pitched-roof buildings, because of its economy and versatility
for a wide range of spans (Morris and Plum, 1988). The connections between the columns and the rafters are
designed to be moment-resistant. Due to these very strong and rigid joints some of the bending moment in the
rafters is transferred to the columns (Ming, 1972). This means that the size of the rafters can be reduced or the
span can be increased for the same size of rafters (Dennis et al., 2004).
Due to the large number of similar framed structures, the desire to automate the design and manufacturing
process has been popular from the very early stage (Dowling et al., 1982). Owing to the continued increase in
the price of materials, civil engineers and manufacturers are forced to reduce the costs of construction and
shorten the implementation period to maintain their competitiveness. As a result, a new design trend was born:
the use of the analysis and design software to evaluate feasible design options, replacing the conventional design
methods (Vasanthakumar et al., 2013). According to Fady (2008), the introduction of software usage in the
structural engineering industry has greatly reduced the complexities of different aspects in the analysis and
design of projects, as well as the amount of time necessary to complete the designs. Concurrently, this leads to
greater savings in material and reductions in costs.
Member sizes can be optimized automatically (Arora and Govil, 1977). The ability of engineers to produce
better designs relies on the techniques available for design optimization (Faluyi and Arum, 2012). Portal frames
for industrial buildings have been extensively studied because of their widespread use. The improvement of the
design methods for portal frames is one of the recurring topics in the field of steel structures (Petr et al., 2010).
Vu and Werner (2009) developed a computer code at the Bauhaus University Weimar, Germany, which aimed to
produce optimum design of portal frames. Ghassan (2012) developed a Matlab-algorithm to find the optimum
design of steel portal frames according to the recommendations of Eurocode 3.
Low (2011) developed a computer algorithm for plane frame analysis by using Matlab with numerical meshfree
method. Abubakar and Abdulkadir (2011) developed a reliability based design program for portal frames.The
program considered analysis of the steel pitched portal frames using elastic analysis, and the design using the
requirements of BS5950. The programming language that was adopted was FORTRAN. In yet another work,
Goh (2011) designed portal frames, based on BS 5950 and Euro code 3 and made comparison between the
designs.
The main goal of this research is to develop a simple task-specific Csharp-based computer program for the
design of fixed-feet pitched-roof portal frames, and establish the relationship between span, slope angle, frame
spacing and mass of framework steel of a sample single storey, fixed-feet pitched-roof portal frame building.
152

Vol.6, No.8, 2014
1.2 Csharp-Based Algorithm
Sedgewick and Wayne (2011) defined an algorithm as a special series of instructions that define how a given
computer problem can be solved in a finite number of steps. C# (pronounced “See Sharp”) is a simple, modern,
object-oriented, and type-safe programming language. C# has its roots in the C family of languages and C, C++,
and Java programmers are acquainted with it (Michealis, 2010).
2. Methodology
The research work was carried out in two stages, which include:
i. Development of a computer program (or code), using Csharp programming language, for the design of
single span, fixed support, pitched-roof portal frame. The program accommodates varying
stanchion/rafter lengths and loadings.
ii. Validation of the design results obtained using the developed code in (i) above by means of established
153
design software (MasterSeries).
2.1 Program Development Steps
The overall process in the development of the program (or code) is shown in a schematic diagram in Figure 1.
2.1.1 Portal Frame Design Outline
Elastic design method was adopted for the design of the portal frame. The design process used to develop the
code for the pitched roof portal frame from BS 5950-1(2000) is summarised as follow:
a) Analysis
Analysis was performed using factored loads (Clause 5.2.2 of BS 5950-1-2000). The program was developed
based on the formulae for rigid frames developed in 1931 by Kleinlogel (as cited by Righiniotis, 2003), for the
analysis of fixed-feet gable frame with vertical legs.
b) Classification of Sections
The section was checked with reference to Clause 3.5.2 and table 11 of BC 5950: Part 1 (2000).
c) Slenderness Check
The slenderness was checked with reference to Annex E.2 and Clause 5.1.3 of BS 5950-1 (2000).
The beam and the column stiffnesses were respectively computed according to Eqns. (1) and (2). Thus:
(1)
(2)
The stiffness of the foundation was assumed equal to the column stiffness.
The distribution factors for the ends of the column-length were obtained by Eqns. (3) and (4) as follows:
(3)
(4)
The effective length ratios about the Y and the X axes were obtained respectively by Eqns (5) and (6).
(5)
(6)
The slenderness ratios about the X and the Y axes were computed using Eqns. (7) and (8) respectively.
λx = (7)
λy = (8)
where;
is column stiffness
is beam stiffness
is length of span
and are the effective lengths about the two orthogonal axes X and Y.
and are the radii of gyration about the two orthogonal axes X and Y.
λx and λy are the slenderness values about the two orthogonal axes X and Y.
d) Compression Resistance
The compression resistance was checked according to Clause 4.7.4 of BS 5950-1 (2000).
For plastic, compact and semi-compact sections the compression resistance Pc is given by Eqn. (9):
Pc = Ag y p (9)
where;
Pc is compression resistance;

Vol.6, No.8, 2014
154
Ag is gross cross-sectional area; and
y p is the compressive strength.
e) Shear Capacity Check
The shear capacity was checked using Clause 4.2.3 of BS 5950-1 (2000).
V y V P  0.6p A (10)
A tD V  (for rolled sections) (11)
where:
V P is the Shear capacity of a member;
y p is the design strength of steel;
V A is the effective shear area;
D is the depth of section; and
t is the thickness of web.
e) Moment Capacity Check
The moment capacity was checked using Clause 4.2.5 of BS 5950-1 (2000). If the shear force Fv is not greater
than 60% of the shear capacity (Fv  0.6Pv) we have the case of low shear. The moment capacity in that case was
determined according to Eqn. (12) for class 1 plastic and class 2 compact sections.
M p S C y  (12)
If the Shear forces Fv is greater than 60% of the shear capacity (Fv ˃ 0.6Pv) we have the case of high shear. The
moment capacity in that case was determined according to Eqn. (13) for class 1 plastic and class 2 compact
sections.
( ) C y V M  p S S (13)
where:
C M is the plastic moment capacity of the section;
y p is the design strength of steel;
S is the plastic modulus;
is reduction factor; and
V S is the plastic modulus of the shear area.
f) Local capacity check
The capacity and buckling resistance of members was checked using Clause 4.8.3.2 of BS 5950-1 (2000). The
cross-sectional capacity of compression members was checked using relationship (14):
+ + (14)
where:
is the ultimate axial compression at the critical location;
is the ultimate bending moment about the major axis;
is the ultimate bending moment about minor axis;
is the gross cross-sectional area of the section of the member;
is the design strength;
is the moment capacity about the major axis (X-X axis); and
is the moment capacity about the minor axis (Y-Y axis).
g) Overall buckling check
The member buckling resistance was checked according to relationship (15) (Ray, 1998) by ensuring that
relationship (15) was satisfied.
+ + (15)
where:
is the compressive strength;
is the ultimate axial compression at the critical location;
is the ultimate bending moment about the major axis;

Vol.6, No.8, 2014
is the ultimate bending moment about the minor axis;
is the gross cross-sectional area of member section;
is the design strength;
is the buckling resistance moment;
 for a single frame (17)
155
m is the equivalent uniform moment factor; and
is the elastic section modulus about the Y-Y axis ( minor axis).
(i) Stability Check
The stability of the frame was checked using the sway-check method (Salter et al., 2004).
 Sway-check method
The sway-check method was used to verify the in-plane stability of the portal frames if each bay satisfies the
following conditions:
(a) Span, L does not exceed five times the mean height h of the columns;
(b) Height, hr of the apex above the tops of the columns does not exceed
0.25 times the span, L.
The ratio of the effective span of a bay to the cross-sectional depth of the rafter must satisfy the inequality (16)
(Salter et al., 2004).

 




L 275
 
 




44 
 
L
 


r yr
b
p
L
h pL
D
4
(16)
In which




 




 

L
h
I
c 2
I
r
where;
D is the cross-section depth of the rafter;
h the mean column height;
Ic the in-plane second moment of area of the column;
Ir the in-plane second moment of area of the rafter;
L the span of the bay;
Lb is the effective span of the bay;
Ω is the arching ratio;
Lr the total developed length of the rafters; and
Pyr the design strength of the rafters in N/mm2.
2.1.2 Coding the outline
CSharp programming language was used as the language to code the design outline into an algorithm.
2.1.3 Implementation of the Developed Program
The graphical interface was created using a windows application called Windows Presentation Foundation
(WPF) in visual studio.Net. Extensible Application Markup Language (XAML) was used to implement the
appearance of the interface.
2.1.4 Testing the Program
Several sets of steel pitched roof portal frame models were designed using the developed program. Those frames
were varied in span, slope angle and frame spacing, as tabulated and shown in Tables 1, 2 and 3.
The dead and imposed loads on the frame were obtained with reference to BS 6399-1 (1997) and information
provided by relevant manufacturers in the case of proprietary products. The loadings are shown in Table 4.
Other relevant information includes the following:
Young Modulus E = 210GPa
Steel Grade y p = 275 N/mm2
2.1.5 Validation of results
Currently, there are quite a number of structural design software applications present in the market. Their use has
become prevalent amongst a majority of structural engineers and engineering firms. An example of these
established software application is MasterSeries.
MasterSeries was used to design the same sets of frames earlier designed using the developed program, in order
to validate the design results obtained using the developed program.

Vol.6, No.8, 2014
2.1.6 Application Flow Chart
The flow diagram illustrating the step by step process of a rigid pitched roof portal frame design as developed in
this research is shown in Fig. 2.
3. Results and Discussions
Several sets of portal frame configurations were set to validate the design results of the developed program.
3.1.1 Design Case 1: Varying Span Length
As shown in Table 1, for this design case, four different spans (30m, 40m, 50m and 60m) were considered for
fixed column height of 6m and slope angle of 6º.
156
a) Analysis
The analysis results from the developed algorithm and MasterSeries were compared. The Maximum bending
moments in each frame are shown in Table 5. The percentage difference between the developed algorithm and
MasterSeries was calculated by Eqn. (18) and the results are shown in Table 5.
% difference = 100 (18)
Similar distributions of bending moments were obtained using the developed program and MasterSeries for the
various portal frame configurations and the values of maximum forces were obtained at the same locations.
Table 5 shows that the developed algorithm gave a maximum difference of 0.78% for the analysis of bending
moment compared with the result from MasterSeries. The cross-sectional area of column and rafter sections in
each frame at varying span length is shown in Table 6 for comparison. As Table 6 shows, the areas of sections of
the frame members increase as the span of the portal frame increases; consequently, the mass of the portal frame
increases. This shows that the longer the span, the greater the mass of the frame.
b) Design check
The design procedure includes the checking of the axial compression, bending moment, as well as the interaction
between the bending and the axial compression to ensure the capacity of the member is sufficient.
3.1.2 Design Case 2: Varying Slope angle
Four different Slope angles (6º, 8º, 10º and 12º) were considered for fixed column height of 6m and frame span
of 30m.
a) Analysis
The results from the developed algorithm and MasterSeries tabulated and compared. The maximum bending
moment values in each frame are shown in Table 7. The table shows that an increase in slope angle translates to
reduction in the maximum moment developed in each frame, which is similar using the developed program and
the MasterSeries. This is logical since moment distribution is dependent on the geometrical properties of the
frame.
b) Design
The cross-sectional areas of column and rafter sections in each frame at varying slope angles are shown in Table
8. The table shows that increase in slope angle translates to reduction in the area of section of the members and
by inference reduction in the mass of the portal frame. This shows that frames with higher pitch are more
economical. Furthermore, Table 8 shows that the cross-sectional areas obtained using Masterseries and the
results obtained by using the developed code, are similar.
3.1.3 Design Case 3: Varying Frame Spacing
Table 9 shows the frame and building details necessary to carry out this design case. Four different frame
spacings (2m, 4m, 6m and 8m) were considered for fixed column height of 6m, frame span of 30m and slope
angle of 6º. The optimum sections obtained for the purlins at varying frame spacing were tabulated for
comparison and shown in Tables 10 and 11. Table 10 shows the comparison of the purlin design section sizes
obtained by using parallel flange channels for frame spacings of 2m and 4m, and universal beam sections for
frame spacings of 6m and 8m. Universal beams were used for 6m and 8m spacings because the depths of the
available standard parallel flange channel sections were inadequate for such spans. Table 11 shows the
comparison of the purlin design section sizes obtained by using universal beam sections only for all frame
spacings considered (2m, 4m, 6m, 8m).
The mass of structural steel of the pitched roof portal frame building as determined for varying spacing using
universal beam sections only, is shown in Tables 12 and 13 for the developed program and for Masterseries
respectively. As both tables show, the mass of purlin increases as the frame spacing increases. Smaller frame
spacing resulted in the initial very low mass of purlin. Finally, the overall mass of the structure increases as the
frame spacing increases.

Vol.6, No.8, 2014
4. Conclusions
The design results obtained using the developed Csharp algorithms were similar to the results obtained using
standard software MasterSeries with greatest variation in the values standing at 0.78%. Besides, this research
work has established the relationship between span, slope angle, frame spacing and mass of framework steel of
single storey, fixed-feet pitched-roof portal frame building. The results show that increase in frame spacing of
the building, results in increase in the mass of framework steel. For instance, for a 24m long fixed-feet frame
building at 2m spacing with slope angle of 6º and span length of 30m, the overall mass of frame was 52,565 kg
whereas a mass of 118,141 kg was obtained for the same building for a frame spacing of 8m.
References
Abubakar, I. and Abdulkadir, O. (2011). Reliability - Based Design of a Rigid Pitched Steel Portal Frame.
International Journal of Civil & Environmental Engineering, IJCEE IJENS Vol. 11, No. 6, pp. 92 – 99.
Arora, J. and Govil, A. (1977). An efficient method for optimal structural design by substructures. Computers
157
and Structures, Vol. 7, pp. 507-515.
Faluyi, F. and Arum, C. (2012). Design Optimization of Plate Girder Using Generalized Reduced Gradient and
Constrained Artificial Bee Colony Algorithms. International Journal of Emerging Technology and
Advanced Engineering, IJETAE Volume 2, Issue 7, pp. 304 – 312.
British Standards Institution (2000). Structural use of steelwork in building. Part 1: Code of practice for design
in simple and continuous construction: hot rolled sections. BS 5950, BSI, London.
British Standards Institution (1997). Loading for buildings. Part 1: Code of practice for dead and imposed loads.
BS 6399, BSI, London.
Dennis, L., Thien, C. and Sing-Ping, C. (2004). Structural Steelwork, Design to Limit State Theory, Elsevier
Butterworth-Heinemann.
Dowling P.J., Mears T., Owens G. and Raven K. (1982). A development in the automated design and fabrication
of portal framed industrial buildings, The Structural Engineer, vol. 60A, pp. 311-319.
Fady, R. S. R. (2008). Computer Analysis and Reinforced Concrete Design of Beams. Fadzter Engineering.
Available from: www.fadzter.com/engineering. (Accessed: 30 January 2014)
Ghassan, N. (2012). Design and optimization of steel portal frames according to Eurocode using genetic
algorithm. A Thesis Submitted in partial fulfilment of the Requirements of Lund Institute of Technology
for the Degree of Master of Science. Sweden: Lund Institute of Technology.
Goh, K. (2011). Analysis and design of pinned base portal frame to euro code 3. A Thesis Submitted in partial
fulfilment of the Requirements of University of Technology Malaysia for the Degree of Master of
Science. Malaysia: University of Technology Malaysia.
Righiniotis, J. (2003). Plane Frame Analysis. In: Davison, B. and Owens, G. W. (Eds). Steel Designers’ Manual;
The Steel Construction Institute; Blackwell Publishing.
Low, G. (2011). Software Development for Plane Frame Analysis by using Matlab with Numerical Meshfree
Method. A Thesis Submitted in Partial Fulfilment of the Requirements of University of Technology
Malaysia for the Degree of Master of Science. Malaysia: University of Technology Malaysia.
Michealis, M. (2010). Essentials of C# 4.0. Pearson Education, Inc., United State.
Ming, C. (1972). Development of Computer Program for the Analysis of Gable Frame using Column Analogy. A
Thesis Submitted in Partial Fulfilment of the Requirements of Brigham Young University for the Degree
of Master of Science. Utah, United State: Brigham Young University
Morris, L. J. and Plum, D. R. (1988). Structural Steelwork Design to BS 5950, Part 1, Longman Scientific &
Technical.
Petr, H., Matti, M. and Ludovic, F. (2010). Advanced design and optimization of steel portal frames. Journal of
Structural Mechanics. Vol. 43, No 1, pp. 44-60.
Ray, S. S. (1998). Structural Steelwork: Analysis and Design, Wiley-Blackwell.
Salter, P., Malik, A., and King, C. (2004). Design of Single Span Steel Portal Frame to BS 5950-1:2000. The
Steel Construction Institute, Berkshire.
Sedgewick, R. and Wayne, K. (2011). Algorithms, Pearson Education, Inc., Boston, 4th Edition.
Vasanthakumar, C., Ganesh, G. M. and Santhi, A. S. (2013). Structural Optimization of an Industrial Building
Frame by Genetic Algorithm, International Journal of Engineering, Science and Technology, IJEST
Vol. 5 No. 06S, pp. 7 – 12.
Vu, A.-T. and Werner, F. (2009). Optimization of Steel Frame Structures Based on Differential Evolution
Algorithm, International Conference on the Application of Computer Science and Mathematics in
Architecture and Civil Engineering; Weimar, Germany.

Vol.6, No.8, 2014
Table 1. Portal Frame with Varied Span (Column Height hc = 6m; Slope Angle =6º; Frame Spacing = 5m)
Frame 1 2 3 4
Span (m) 30 40 50 60
Table 2. Portal Frame with Varied Slope Angle (Column Height hc = 6m; Span = 30m; Frame Spacing = 5m)
Frame 1 2 3 4
Slope Angle (º) 6 8 10 12
Table 3. Portal Frame with Varied Frame Spacing (Column Height hc = 6m; Span = 30m; Slope Angle = 6º)
Building (Length = 1 2 3 4
Frame Spacing (m) 2 4 6 8
158
Table 4. Portal Frame Loadings
Load Contributor Sheetings Purlins Frame Services Total Dead
Load
Total Live
Load
Load (kN/m2) 0.04 0.07 0.11 0.28 0.5 0.6
Table 5. Comparison of Maximum Bending Moments in Each Frame at Varying Span Length
Maximum Bending Moment (kNm)
Span Length (m) Developed Algorithm MasterSeries % Difference
30 508.2 510.8 0.509
40 811.2 817.6 0.783
50 1276.1 1280.9 0.383
60 1864.7 1860.5 0.226
Table 6. Comparison of Area of section at Varying Span Length
Area of section, cm2
Developed Code MasterSeries
Span Length (m) Column Rafter Column Rafter
30 117 105 117 105
40 159 159 159 159
50 220 220 220 220
60 286 256 256 256
Table 7. Comparison of Maximum Bending Moments in Each Frame at Varying Slope Angle
Maximum Bending Moment (kNm)
Slope Angle (º) Developed Code MasterSeries % Difference
6 508.2 510.8 0.509
8 498.8 499 0.040
10 461.8 461.4 0.087
12 446.2 446.52 0.072
Table 8. Comparison of Area of Section at Varying Slope Angle
Area of section, cm2
Developed Code MasterSeries
Slope Angle (º) Column Rafter Column Rafter
6 117 105 117 105
8 117 105 117 105
10 105 104 104 104
12 105 104 104 104

Vol.6, No.8, 2014
Table 9. Additional Details of the Pitched-roof Portal Frame Building
Length of Building (L) 24m
Slope Angle 6º
Height of Roof 1.58m
Rafter Length (Lr) 15.1m
Number of Purlins (along Slope) 25 @ 1.2m interval
Table 10. Comparison of Purlin Design Section Sizes at Varying Frame Spacing using Parallel Flange and
Universal Beam Sections
Section Designation
Frame Spacing (m) Developed Program MasterSeries Section Name
2 150x75x18 150x75x18 Parallel Flange Channel
4 380x100x54 380x100x54 Parallel Flange Channel
6 457x191x98 533x210x92 Universal Beam
Table 11. Comparison of Purlin Design Section Sizes at Varying Frame Spacing using Universal Beam Sections
only
Section Designation
Frame Spacing (m) Developed Algorithm MasterSeries Section Name
Table 12. Variation of Mass of Structural Steel of a Fixed-feet Pitched-Roof Building using the Developed
Program
159
Frame
Spacing
s
(m)
Number of
frame
nf =(L/s)
Mass of
Rafters
MR
(kg)
Mass of
Columns
MC
(kg)
Mass of
Frame
MF = (MR+
MC)
(kg)
Mass of
Purlin
(MP)
(kg)
Mass of
Structure
(MS) =
(MF + MP)
(kg)
2 12 29,717 13,248 42,965 9,600 52,565
4 6 14,858 6,624 21,482 34,200 55,682
6 4 9,906 4,416 14,322 58,800 73,122
8 3 7,429 3,312 10,741 102,000 112,741
Table 13. Variation of Mass of Structural Steel of a Fixed-feet Pitched-roof Building using MasterSeries
Frame
Spacing
s
(m)
Number of
frame
nf =(L/s)
Mass of
Rafter
MR
(kg)
Mass of
Column
MC
(kg)
Mass of Frame
MF = (MR+ MC)
(kg)
Mass of
Purlin
(MP)
(kg)
Mass of
Structure
(MS) =
(MF + MP)
(kg)
2 12 29,717 13,248 42,965 9,600 52,565
4 6 14,858 6,624 21,482 34,200 55,682
6 4 9,906 4,416 14,322 55,200 69,522
8 3 7,429 3,312 10,741 107,400 118,141

Vol.6, No.8, 2014
160

Vol.6, No.8, 2014
Figure 3. Relationship between Frame spacing and Mass of Purlin
161

Vol.6, No.8, 2014
Figure 4. Relationship between Frame Spacing and Mass of Frame
Figure 5. Relationship between Frame Spacing and Mass of Structure
162

The IISTE is a pioneer in the Open-Access hosting service and academic event
management. The aim of the firm is Accelerating Global Knowledge Sharing.
More information about the firm can be found on the homepage:
http://www.iiste.org
CALL FOR JOURNAL PAPERS
There are more than 30 peer-reviewed academic journals hosted under the hosting
platform.
Prospective authors of journals can find the submission instruction on the
following page: http://www.iiste.org/journals/ All the journals articles are available
online to the readers all over the world without financial, legal, or technical barriers
other than those inseparable from gaining access to the internet itself. Paper version
of the journals is also available upon request of readers and authors.
MORE RESOURCES
Book publication information: http://www.iiste.org/book/
IISTE Knowledge Sharing Partners
EBSCO, Index Copernicus, Ulrich's Periodicals Directory, JournalTOCS, PKP Open
Archives Harvester, Bielefeld Academic Search Engine, Elektronische
Zeitschriftenbibliothek EZB, Open J-Gate, OCLC WorldCat, Universe Digtial
Library , NewJour, Google Scholar

Development of csharp based computer program for the design of single

More Related Content

What's hot (19)

Viewers also liked (20)

Similar to Development of csharp based computer program for the design of single (20)

More from Alexander Decker (20)

Recently uploaded (20)

Development of csharp based computer program for the design of single