Performance Analysis of MIMO Equalization Techniques with Highly Efficient Channel Coding Schemes
0 likes70 views
1. The document analyzes the performance of MIMO equalization techniques when combined with highly efficient channel coding schemes like turbo codes. 2. It simulates the combination of MIMO techniques (ML, MMSE) with turbo codes and analyzes the bit error rate (BER) achieved at different signal to noise ratios (SNR). 3. The results show that combining MIMO with channel coding achieves a BER of 10-6 at much lower SNR values (between -3 to 5 dB) compared to using MIMO alone (which requires 10-20 dB SNR). The best performance was obtained using a 2x4 MIMO configuration with ML equalization.
![1 International Journal for Modern Trends in Science and Technology
Volume: 2 | Issue: 08 | August 2016 | ISSN: 2455-3778IJMTST
Performance Analysis of MIMO
Equalization Techniques with Highly
Efficient Channel Coding Schemes
Neha Aggarwal1
| Shalini Bahel2
| Teglovy Singh Chohan3
| Jasdeep Singh4
1,2,3,4 Department of Electronics Technology, Guru Nanak Dev University, Amritsar, Punjab, India.
To combat the wireless fading impairment in the high network demand environment, various coding
schemes have been implemented. MIMO techniques are still the powerful techniques along with source
coding. This paper focuses on coherent implementation of high performance turbo codes with MIMO
equalization techniques. It is proposed to achieve optimum BER value at very low values of SNR in a noisy
environment.
KEYWORDS: Turbo Codes, MIMO, Maximal Likelihood Technique, Minimum Mean Square Error Technique
Copyright © 2016 International Journal for Modern Trends in Science and Technology
All rights reserved.
Abbreviations Used:
MIMO- Multi-Input Multi-Output
ML- Maximal Likelihood
MMSE- Minimum Mean Square Error
BER- Bit Error Rate
SNR- Signal to Noise Ratio
I. INTRODUCTION
The quality of a wireless link can be described by
three basic parameters, namely the transmission
rate, the transmission range and the transmission
reliability. The transmission reliability may be
improved by reducing the transmission rate and
range [1]. However, with the advent of multiple
transmit and receive antenna (MIMO) techniques,
the above-mentioned three parameters may
simultaneously be improved. An increased
capacity, coverage and reliability are achievable
with the aid of MIMO techniques [2]. Furthermore,
although MIMOs can potentially be combined with
any modulation or multiple access technique,
recent research suggests that the implementation
of MIMO with channel coding schemes is more
efficient. Multi-antenna implementation such as
MIMO scheme enhances the coverage and capacity
in even the most challenging environments [3].
Considering advantages of various MIMO
techniques, there is a need to integrate them so
that the whole system can get benefit from these
technologies. In this paper, it is demonstrated that
the combination of MIMO equalization techniques
and channel coding techniques is a promising
scheme for future multimedia wireless
communication systems and other applications of
MIMO like LTE, WIMAX, WLAN etc.
Some of these MIMO equalization techniques and
Turbo codes are explained in the subsequent
sections.
A. MIMO Schemes
Multiple transmit and receive antennas (MIMO) are
used to increase the capacity of the channel and to
fulfil the requirement of information rate [4]. MIMO
equalization techniques are:
a) Maximum likelihood technique (ML):
The Maximum Likelihood receiver minimizes,
J= 𝑦 − 𝐻𝑥 2
(1)
It computes the transmitted signal estimation. This
is generally easy to derive.
b) Minimum Mean Square Error (MMSE):
An MMSE estimator is a method which reduces the
mean square error (MSE). MMSE equalizer does
not completely exclude Inter Symbol Interference
(ISI) but minimizes the total power of the noise and
ISI components in the output.
B. Turbo codes
Turbo codes are high-performance Forward Error
Correction Codes (FEC) developed in 1993. Turbo
codes uses Recursive Systematic Convolution
(RSC) Encoder and Iterative BCJR (Bahl Cocke
Jelinek Raviv) decoder. Turbo encoder is
constituted of two rate 1/2 RSC encoders
ABSTRACT](https://image.slidesharecdn.com/115ijmtst020801-160810042527/85/Performance-Analysis-of-MIMO-Equalization-Techniques-with-Highly-Efficient-Channel-Coding-Schemes-1-320.jpg)
![2 International Journal for Modern Trends in Science and Technology
Performance Analysis of MIMO Equalization Techniques with Highly Efficient Channel Coding Schemes
combined in parallel to form Turbo coded signal
with rate 1/3 [5]. The message signal is encoded
with the RSC turbo encoder. Secondly, the
message signal is interleaved with random
interleaver and encoded again [6]. Then these two
encoded signals are multiplexed with the original
message signal to form rate 1/3 turbo encoded
signal. Then after channel transmission, decoding
is done with BCJR algorithm where Log likelihood
ratio is evaluated and the output is retrieved.
II. METHODOLOGY
In this paper, a reliable transmission channel
has been designed comprising of digital data
synthesiser, encoder, modulator, MIMO
transmitter and receiver antennas, wireless
channel, demodulator, turbo decoder and the
digital data output. The (1, 15/13, 15/13) RSC
turbo encoder along with BCJR decoder in
algorithm Max-Log-MAP has been used for
encoding and decoding purposes respectively [7].
Various MIMO equalization schemes like ML and
MMSE have been simulated with iterative turbo
coding schemes [8]. Thermal noise has been
modelled as Additive white Gaussian noise (AWGN)
and fading as Rayleigh fading [9, 10].
Fig.1 Simulation model
III. SIMULATION RESULTS
The details of the simulated work have been given
in the following section:
Table I: Simulated Parameters
PARAMETER VALUE
No. of bits 106
Turbo Encoder RSC [1, 15/13, 15/13]
Encoder
Decoder BCJR
Wireless channel AWGN, Rayleigh Fading
Antenna diversity MIMO
Modulation BPSK
MIMO Equalization
scheme
ML, MMSE
Signal to Noise Ratio
(SNR)
-6 to 25 (dB)
No. of iterations 4
Algorithm for BCJR
decoder
Max-Log-Map
No. of
Transmitter-Receivers
2X2, 2X3, 2X4
IV. RESULTS
Initially, the variation of Bit Error Rate (BER) with
respect to SNR (in dB) for Turbo Decoder
implemented with AWGN channel and BPSK
modulation is shown.
Fig.2 Simple Turbo Performance without MIMO scheme
From fig.2, it has been observed that the
performance of Turbo codes improved with the
number of increasing iterations. It is noted that
BER becomes 10−6
at 2.5 dB of SNR after 3
iterations and at 2 dB of SNR after 4th iteration.
MIMO-ML equalization performance with Turbo
Coding
Fig.3 Turbo Coded Performance with 2X2 MIMO ML
equalization scheme
In fig.3, the variation of BER Vs SNR for the
combination of ML equalization technique with
turbo coding scheme in a wireless communication](https://image.slidesharecdn.com/115ijmtst020801-160810042527/85/Performance-Analysis-of-MIMO-Equalization-Techniques-with-Highly-Efficient-Channel-Coding-Schemes-2-320.jpg)
![4 International Journal for Modern Trends in Science and Technology
Performance Analysis of MIMO Equalization Techniques with Highly Efficient Channel Coding Schemes
of bandwidth which is not acceptable in the design
of communication channel.
Fig.8 Turbo Coded Performance with 2X4 MIMO MMSE
equalization scheme
BER Performance after 4th Iteration
In this section, various MIMO equalization
techniques have been compared on the basis of
BER values achieved after 4th iteration of turbo
encoding and decoding process for 2X4 MIMO
scheme. In Fig.9 and Fig.10, the results are
presented for the variation of BER with respect to
SNR for ML and MMSE techniques respectively
with varying number of transmitter and receiver
antennas.
Fig.9 BER plot for various MIMO schemes for ML after 4th
Iteration
Fig.10 BER plot for various MIMO schemes for MMSE after
4th Iteration
From fig.9 and fig.10, it is clearly inferred that
with change in number of transmitting and
receiving antennas, the performance upgrades to
acceptable levels. 2X4 MIMO system gives the best
performance as compared to corresponding 2X3
and 2X2 MIMO systems. In all types of MIMO
simulations, ML equalization performs better than
MMSE equalization and provides superior results.
ML needs less number of decoding iterations as
compared to that of MMSE for same value of Bit
error rate (BER).
V. CONCLUSION
From the Results explained above, it is
concluded that the performance of MIMO
equalization techniques implemented with channel
coding is superior to the MIMO techniques
implemented without coding. BER achieved is 10−6
in the range of 10-20 dB of SNR without coding and
is in the range of -3 to 5 dB of SNR with the use of
channel coding. The simulated model can be
applied in GPS signals, Radar applications etc. In
near future, the performance can be enhanced
further by increasing number of antennas and by
using other equalization techniques.
REFERENCES
[1] V. Tarokh, N. Seshadri, and A. R. Calderbank,
“Space-time block codes from orthogonal designs",
IEEE Trans. on IT,Vol. 45, pp. 1456-1467, July 1999.
[2] S. M. Alamouti, "A simple transmit diversity
technique for wireless Communications", IEEE
JSAC, Vol. 16, No. 8, pp.1451-1458, October 1998.
[3] Suchita Varade, Kishore Kulat, “Performance
Analysis of MIMO-OFDM System using Space-time
Turbo Codes and Adaptive Beamforming”,
International Journal of Computer Applications (0975
– 8887) Volume 22– No.3, May 2011.
[4] Yong soo cho, jaekwon kim, won young yang,
chung-gu kang, “MIMO-OFDM wireless
communications with matlab” by wiley publications.
[5] “Turbo Encoder & Decoder Implementation and Its
Performance Over AWGN Channel For BPSK
Modulated Symbols” by Yogesh Kumar Soniwal, IIT
Kanpur.
[6] IEEE transactions on information theory, vol. 51, no.
1, January 2005 101 “Interleavers for Turbo Codes
Using Permutation Polynomials Over Integer Rings”
Jing Sun, and Oscar Y. Takeshita.
[7] Journal of Expert Systems (JES) ` 115 Vol. 2, No. 1,
2013, ISSN 2169-3064, United States,
“Implementation and Analysis of Turbo Codes Using
MATLAB”, Nabeel Arshad, Abdul Basit.
[8] “Turbo codes and iterative processing”, Mathew c.
Valenti, mobile and portable radio research group,
Virginia polytechnic institute and state university,
Blacksburg, USA.](https://image.slidesharecdn.com/115ijmtst020801-160810042527/85/Performance-Analysis-of-MIMO-Equalization-Techniques-with-Highly-Efficient-Channel-Coding-Schemes-4-320.jpg)
![5 International Journal for Modern Trends in Science and Technology
Volume: 2 | Issue: 08 | August 2016 | ISSN: 2455-3778IJMTST
[9] Yong soo cho, jaekwon kim, won young yang,
chung-gu kang “MIMO-OFDM wireless
communications with matlab” by Wiley publications.
[10]Naval Postgraduate School Monterey, California
“Modelling, simulation and performance Analysis of
multiple-input multiple-output (MIMO) systems with
multicarrier time delay Diversity modulation” by
Muhammad Shahid.](https://image.slidesharecdn.com/115ijmtst020801-160810042527/85/Performance-Analysis-of-MIMO-Equalization-Techniques-with-Highly-Efficient-Channel-Coding-Schemes-5-320.jpg)
Performance Analysis of MIMO Equalization Techniques with Highly Efficient Channel Coding Schemes
- 1. 1 International Journal for Modern Trends in Science and Technology Volume: 2 | Issue: 08 | August 2016 | ISSN: 2455-3778IJMTST Performance Analysis of MIMO Equalization Techniques with Highly Efficient Channel Coding Schemes Neha Aggarwal1 | Shalini Bahel2 | Teglovy Singh Chohan3 | Jasdeep Singh4 1,2,3,4 Department of Electronics Technology, Guru Nanak Dev University, Amritsar, Punjab, India. To combat the wireless fading impairment in the high network demand environment, various coding schemes have been implemented. MIMO techniques are still the powerful techniques along with source coding. This paper focuses on coherent implementation of high performance turbo codes with MIMO equalization techniques. It is proposed to achieve optimum BER value at very low values of SNR in a noisy environment. KEYWORDS: Turbo Codes, MIMO, Maximal Likelihood Technique, Minimum Mean Square Error Technique Copyright © 2016 International Journal for Modern Trends in Science and Technology All rights reserved. Abbreviations Used: MIMO- Multi-Input Multi-Output ML- Maximal Likelihood MMSE- Minimum Mean Square Error BER- Bit Error Rate SNR- Signal to Noise Ratio I. INTRODUCTION The quality of a wireless link can be described by three basic parameters, namely the transmission rate, the transmission range and the transmission reliability. The transmission reliability may be improved by reducing the transmission rate and range [1]. However, with the advent of multiple transmit and receive antenna (MIMO) techniques, the above-mentioned three parameters may simultaneously be improved. An increased capacity, coverage and reliability are achievable with the aid of MIMO techniques [2]. Furthermore, although MIMOs can potentially be combined with any modulation or multiple access technique, recent research suggests that the implementation of MIMO with channel coding schemes is more efficient. Multi-antenna implementation such as MIMO scheme enhances the coverage and capacity in even the most challenging environments [3]. Considering advantages of various MIMO techniques, there is a need to integrate them so that the whole system can get benefit from these technologies. In this paper, it is demonstrated that the combination of MIMO equalization techniques and channel coding techniques is a promising scheme for future multimedia wireless communication systems and other applications of MIMO like LTE, WIMAX, WLAN etc. Some of these MIMO equalization techniques and Turbo codes are explained in the subsequent sections. A. MIMO Schemes Multiple transmit and receive antennas (MIMO) are used to increase the capacity of the channel and to fulfil the requirement of information rate [4]. MIMO equalization techniques are: a) Maximum likelihood technique (ML): The Maximum Likelihood receiver minimizes, J= 𝑦 − 𝐻𝑥 2 (1) It computes the transmitted signal estimation. This is generally easy to derive. b) Minimum Mean Square Error (MMSE): An MMSE estimator is a method which reduces the mean square error (MSE). MMSE equalizer does not completely exclude Inter Symbol Interference (ISI) but minimizes the total power of the noise and ISI components in the output. B. Turbo codes Turbo codes are high-performance Forward Error Correction Codes (FEC) developed in 1993. Turbo codes uses Recursive Systematic Convolution (RSC) Encoder and Iterative BCJR (Bahl Cocke Jelinek Raviv) decoder. Turbo encoder is constituted of two rate 1/2 RSC encoders ABSTRACT
- 2. 2 International Journal for Modern Trends in Science and Technology Performance Analysis of MIMO Equalization Techniques with Highly Efficient Channel Coding Schemes combined in parallel to form Turbo coded signal with rate 1/3 [5]. The message signal is encoded with the RSC turbo encoder. Secondly, the message signal is interleaved with random interleaver and encoded again [6]. Then these two encoded signals are multiplexed with the original message signal to form rate 1/3 turbo encoded signal. Then after channel transmission, decoding is done with BCJR algorithm where Log likelihood ratio is evaluated and the output is retrieved. II. METHODOLOGY In this paper, a reliable transmission channel has been designed comprising of digital data synthesiser, encoder, modulator, MIMO transmitter and receiver antennas, wireless channel, demodulator, turbo decoder and the digital data output. The (1, 15/13, 15/13) RSC turbo encoder along with BCJR decoder in algorithm Max-Log-MAP has been used for encoding and decoding purposes respectively [7]. Various MIMO equalization schemes like ML and MMSE have been simulated with iterative turbo coding schemes [8]. Thermal noise has been modelled as Additive white Gaussian noise (AWGN) and fading as Rayleigh fading [9, 10]. Fig.1 Simulation model III. SIMULATION RESULTS The details of the simulated work have been given in the following section: Table I: Simulated Parameters PARAMETER VALUE No. of bits 106 Turbo Encoder RSC [1, 15/13, 15/13] Encoder Decoder BCJR Wireless channel AWGN, Rayleigh Fading Antenna diversity MIMO Modulation BPSK MIMO Equalization scheme ML, MMSE Signal to Noise Ratio (SNR) -6 to 25 (dB) No. of iterations 4 Algorithm for BCJR decoder Max-Log-Map No. of Transmitter-Receivers 2X2, 2X3, 2X4 IV. RESULTS Initially, the variation of Bit Error Rate (BER) with respect to SNR (in dB) for Turbo Decoder implemented with AWGN channel and BPSK modulation is shown. Fig.2 Simple Turbo Performance without MIMO scheme From fig.2, it has been observed that the performance of Turbo codes improved with the number of increasing iterations. It is noted that BER becomes 10−6 at 2.5 dB of SNR after 3 iterations and at 2 dB of SNR after 4th iteration. MIMO-ML equalization performance with Turbo Coding Fig.3 Turbo Coded Performance with 2X2 MIMO ML equalization scheme In fig.3, the variation of BER Vs SNR for the combination of ML equalization technique with turbo coding scheme in a wireless communication
- 3. 3 International Journal for Modern Trends in Science and Technology Volume: 2 | Issue: 08 | August 2016 | ISSN: 2455-3778IJMTST channel for 2 transmitters and 2 receivers is shown. The performance improved with the number of receiver antennas even with less number of iterations. The achieved value of BER is 10−6 after 1.5 dB of SNR for 2nd iteration and at -0.5 dB of SNR for 4th iteration. This implementation has further been done for more number of receiver antennas and the results have been summarized in the subsequent sections. Fig.4 Turbo Coded Performance with 2X3 MIMO ML equalization scheme In fig.4, the results of ML equalization technique simulated with turbo codes have been discussed taking two transmitters and three receiver antennas. In this case, the performance of BER is enhanced. The achieved value of BER is 10−6 at -2.5 dB of SNR for 4th iteration where signal strength is very low so this technique is suitable for challenging noisy environments. Fig.5 Turbo Coded Performance with 2X4 MIMO ML equalization scheme Fig.5 shows the variation of BER vs. SNR for 2X4 MIMO-ML scheme implemented with turbo codes. Here BER is 10−6 at very low value of SNR i.e. -3.5 dB after four decoding iterations only. This takes very less time to send the data reliably to the receiving side without any error or if any, that is also negligible. MIMO-MMSE equalization performance with Turbo Coding In this section, MMSE equalization MIMO scheme has been implemented with channel coding schemes. Fig.6 Turbo Coded Performance with 2X2 MIMO MMSE equalization scheme In fig.6, the performance improved rapidly with number of increasing iterations. The achieved value of BER is 10−6 at 0.5 dB of SNR after 4th iteration in 2X2 MIMO scheme. Fig.7 Turbo Coded Performance with 2X3 MIMO MMSE equalization scheme When 2X3 MIMO scheme is implemented in fig.7, it takes less number of iterations to converge the BER at same rate as that of 2X2 MIMO scheme. Now BER is approximately 10−6 at -2.5 dB of SNR after 4th iteration. The best performance is given by 2X4 MIMO scheme implemented with turbo codes as shown in fig.8. Here BER is equal to 10−6 at -3 dB of SNR after 4th iteration. This is very low signal strength and t can be efficiently applied in challenging situations. The number of receivers is not increased beyond this as it can affect the cost and complexity constraints. It can also lead to wastage
- 4. 4 International Journal for Modern Trends in Science and Technology Performance Analysis of MIMO Equalization Techniques with Highly Efficient Channel Coding Schemes of bandwidth which is not acceptable in the design of communication channel. Fig.8 Turbo Coded Performance with 2X4 MIMO MMSE equalization scheme BER Performance after 4th Iteration In this section, various MIMO equalization techniques have been compared on the basis of BER values achieved after 4th iteration of turbo encoding and decoding process for 2X4 MIMO scheme. In Fig.9 and Fig.10, the results are presented for the variation of BER with respect to SNR for ML and MMSE techniques respectively with varying number of transmitter and receiver antennas. Fig.9 BER plot for various MIMO schemes for ML after 4th Iteration Fig.10 BER plot for various MIMO schemes for MMSE after 4th Iteration From fig.9 and fig.10, it is clearly inferred that with change in number of transmitting and receiving antennas, the performance upgrades to acceptable levels. 2X4 MIMO system gives the best performance as compared to corresponding 2X3 and 2X2 MIMO systems. In all types of MIMO simulations, ML equalization performs better than MMSE equalization and provides superior results. ML needs less number of decoding iterations as compared to that of MMSE for same value of Bit error rate (BER). V. CONCLUSION From the Results explained above, it is concluded that the performance of MIMO equalization techniques implemented with channel coding is superior to the MIMO techniques implemented without coding. BER achieved is 10−6 in the range of 10-20 dB of SNR without coding and is in the range of -3 to 5 dB of SNR with the use of channel coding. The simulated model can be applied in GPS signals, Radar applications etc. In near future, the performance can be enhanced further by increasing number of antennas and by using other equalization techniques. REFERENCES [1] V. Tarokh, N. Seshadri, and A. R. Calderbank, “Space-time block codes from orthogonal designs", IEEE Trans. on IT,Vol. 45, pp. 1456-1467, July 1999. [2] S. M. Alamouti, "A simple transmit diversity technique for wireless Communications", IEEE JSAC, Vol. 16, No. 8, pp.1451-1458, October 1998. [3] Suchita Varade, Kishore Kulat, “Performance Analysis of MIMO-OFDM System using Space-time Turbo Codes and Adaptive Beamforming”, International Journal of Computer Applications (0975 – 8887) Volume 22– No.3, May 2011. [4] Yong soo cho, jaekwon kim, won young yang, chung-gu kang, “MIMO-OFDM wireless communications with matlab” by wiley publications. [5] “Turbo Encoder & Decoder Implementation and Its Performance Over AWGN Channel For BPSK Modulated Symbols” by Yogesh Kumar Soniwal, IIT Kanpur. [6] IEEE transactions on information theory, vol. 51, no. 1, January 2005 101 “Interleavers for Turbo Codes Using Permutation Polynomials Over Integer Rings” Jing Sun, and Oscar Y. Takeshita. [7] Journal of Expert Systems (JES) ` 115 Vol. 2, No. 1, 2013, ISSN 2169-3064, United States, “Implementation and Analysis of Turbo Codes Using MATLAB”, Nabeel Arshad, Abdul Basit. [8] “Turbo codes and iterative processing”, Mathew c. Valenti, mobile and portable radio research group, Virginia polytechnic institute and state university, Blacksburg, USA.
- 5. 5 International Journal for Modern Trends in Science and Technology Volume: 2 | Issue: 08 | August 2016 | ISSN: 2455-3778IJMTST [9] Yong soo cho, jaekwon kim, won young yang, chung-gu kang “MIMO-OFDM wireless communications with matlab” by Wiley publications. [10]Naval Postgraduate School Monterey, California “Modelling, simulation and performance Analysis of multiple-input multiple-output (MIMO) systems with multicarrier time delay Diversity modulation” by Muhammad Shahid.