RajeevCV2016
- 1. PROFILE I have 18+ years of Oil and Gas work experience in the areas of Process, Flow assurance, and Project Engineering. This experience has been over the full project life-cycle from concept evaluation, through front-end and detailed engineering and de-bottlenecking at various stages of a typical project life cycle; from Conceptual design thru to Brown Field debottlenecking projects. KEY QUALIFICATIONS Imperial College, United Kingdom. Master of Engineering (MENG) Honours, in Chemical Engineering with Management, 1995. SOFTWARE SKILLS Proficient in the use of the following technical software: OLGA, HYSYS, PIPESIM, PVTSIM, MULTIFLASH, PIPENET, FLARENET, FLARESIM, PIPEPHASE, Mathematica and PRO 2. EXPERIENCE Title: Lead Flow Assurance Engineer (Independent Consultant) Company: Wood Group Kenny Pty. Ltd. Duration: September 2008 to December 2015 PROJECT HIGHLIGHTS Lambert Deep Pre-Commissioning Support Project: As the study engineer and manage, I was responsible for the requisite OLGA simulation work and associated deliverables. The purpose of the study was to is to support the pre-commissioning effort for the Lambert Deep infield flowline by furnishing some preliminary information pertaining to flowline dewatering, re-pressurization with Nitrogen and/or Hydrocarbon gas during the initial start- up process. CLIENT: Woodside Energy Limited Okha Liquids Management Project: As the study engineer and manager, I was responsible for the execution of all technical and managerial requirements. The purpose the study was to assess whether it would be possible to operate the Okha FPSO without inlet separation facilities during fuel gas import, via a subsea pipeline. The study also investigated compositional impacts, liquid dropout rates, flow stability and inlet surge volumes. CLIENT: Woodside Energy Limited Hess-Equus Phase 2A Project: As Flow Assurance Lead, I was responsible for the execution of all FA CTRs for the various FA focus areas, covering areas such as the Steady state (incl.
- 2. line sizing/Integrated production modelling/Flow stability assessment/Temperature management) / Transient Analysis (incl. Liquid management) of the infield subsea gathering and Gas Export pipeline, Hydrate management, Subsea production system operating conditions. I was responsible for the Phase 2A update to the FA design premise including the provision of the FA information required to support the subsea production system mechanical design and integrity management (corrosion and material selection). I was also responsible for the technical integrity and assurance associated with all FA deliverables, and was the FA discipline project representative at all project technical meetings. CLIENT: HESS Australia Pty. Ltd. Bonaparte Concept Definition FLNG Project: As Flow Assurance Lead, I was responsible for the execution of all FA CTRs for the various FA focus areas, covering areas such as the Steady state (incl. line sizing) / Transient Analysis (incl. Liquid management) of the subsea gathering system , Hydrate management, Solids management, Subsea production system operating conditions and FLNG inlet facilities controllability assessment. I was responsible for the development of the FA design premise including the provision of the FA information required to support the subsea production system mechanical design and integrity management (corrosion and material selection). I am also responsible for the technical integrity and assurance associated with all FA deliverables excluding the IPM scope, and am the FA discipline representative at all project technical reviews, VIP and risk workshops. CLIENT: Gaz De France Suez Gorgon Expansion Project: As Upstream Process Engineer, I was responsible for the development of the FA schedule and work plans for various FA focus areas in Phase 2 covering areas such as Looped vs. Unlooped Pipeline operation, Liquid Management, Flowline Sizing, MEG and Utility System FA design, Superspan Slugging Assessment and Solids transportation. I performed the FA analysis on the Preferred Business Case option for the Early Phase 2 FA work incl. SS simulation runs to estimate backpressures/ liquid hold- ups, Min. Turndown rates and wall shear stress estimates; Transient runs required to provide Surge volume estimates for Ramp-up/ Restart/Pigging. I produced the presentation material for the Joint Venture Partner FA Peer Assist / Technical review and participated in these peer assists. I produced the FA Phase 2B Summary Report, Phase 2 B Sand Transportability Assessment, FA design premise and Hydrate management strategy and was responsible for the development of the FA design premise and hydrate / sand management strategy for FEED including the provision of cross discipline FA information requirements and providing technical assurance for FA deliverables. CLIENT: Chevron Australia Pty Ltd Commingled Flow Assurance Study for Hai Su Trang and Hai Su Den Early Field Development Project (Phase 1): As Staff Consultant, I was responsible for Line sizing and Thermo hydraulic Steady State modelling of the pipeline network from the HSD platform to the FPSO via the HST and TGT H1 platforms. The scope included the establishment of heater duty, flowline insulation requirements, analysis of shutdown/cooldown/restart pressure requirements. CLIENT: THANG LONG JOINT OPERATING COMPANY
- 3. Ichthys LNG Project FEED: As Lead Flow Assurance Engineer during the FEED phase, I was overall responsible for all Technical Integrity issues related to the Flow assurance design of the Infield Subsea Gathering System, Subsea MEG/Chemical injection system, Gas Export System and Transfer System. Overall responsible for providing direction for flow assurance design activities, developing operating strategies and the development and review of associated deliverables. Provide technical input to system integration and operability and the development of CTRs/ VOs and interface with other disciplines and design contractors to ensure overall alignment. CLIENT: INPEX AUSTRALIA PTY. LTD. Browse LNG Project Pre-FEED: Responsible for all project engineering activities including the preparation of CTRs, progress reports, activity scheduling and technical input/ interfacing related to System engineering issues. Other responsibilities included the supervision of flow assurance design activities and the review/ approval of associated deliverables. Flow Assurance issues investigated included areas such as Line size optimization, start-up and ramp-up surges, temperature management and insulation requirements, and wax management through pigging to establish optimal pigging frequencies. CLIENT: WOODSIDE ENERGY PTY. LTD. Title: Principal / Lead Process Engineer Company: GENESIS OIL AND GAS CONSULTANTS PTY. LTD. Duration: January 2007- August 2008 Blacktip Onshore gas plant Detailed Design: As Lead Engineer, was overall responsible for all Onshore Gas plant design Technical Integrity for the Process and Utility systems design. As Lead Engineer responsible for the production, development and approval of all Detailed Engineering Process deliverables to AFC status, and for all follow-on engineering activities. As Principal Engineer, was responsible for the production and review of Detailed Process engineering deliverables related to the gas compression, gas dew-pointing, inlet separation and condensate storage/offloading System for the Onshore Gas Plant. CLIENT: ENI AUSTRALIA PTY. LTD. Title: Sr. Process/ Flow Assurance Engineer Company: MUSTANG ENGINEERING PTY. LTD. Duration: January 2005-December 2006 PROJECT HIGHLIGHTS
- 4. The Gorgon Project: As Sr. Flow Assurance / Process Engineer was responsible for the design production and development of Process / Flow Assurance deliverables such as calculations, PFDs/P&IDs and datasheets for the Subsea Gathering system and onshore receiving facilities, MEG/Chemical injection systems and Utility system associated with the subsea production system. The work performed included a conceptual study to determine Compression platform design requirements for the MP and LP compression phases and produce a preliminary cost estimate for the topsides process facility. CLIENT: Chevron Australia Pty Ltd Third Transmission Pipeline Project: As Sr. Flow Assurance / Process Engineer was responsible for the development of subsea network P&IDs and Operating Philosophies for Three Large Diameter Sour gas pipelines. CLIENT: PTT PUBLIC COMPANY THAILAND KRA South Hydraulic Study: Performed Thermo-Hydraulic Analysis to establish system capacity/constraints and optimize proposed subsea architecture. CLIENT: PTT PUBLIC COMPANY THAILAND SAPI gas pipeline tie-in temperature profile assessment: Investigated the impact of gas mixing at a new tie-in to an existing trunkline on the design temperature of the trunkline by estimating the temperature profile for the turbulent jets in cross flow based on turbulent mixing lengths and ambient heat transfer. CLIENT: UNOCAL INDONESIA BHP Billiton Stybarrow Flow Assurance Study: Produced the Flow assurance philosophies associated with liquid management and hydrate management and determined THI injection requirements. I was responsible for the development of “high level” procedures for Start-up, Ramp-up, Turndown, Depressurisation and Pigging. CLIENT: BHP BILLITON PTY. LTD. Crux FPSO NGL Recovery Project: Responsible engineer for the FPSO based inlet separation, gas dew-pointing, TEG dehydration and compression system. Produced design deliverables such as PFDs, PSFS, P&IDs, calculations, philosophies and datasheets. CLIENT: NEXUS ENERGY PTY. LTD. Title: Principal Process / Flow Assurance Engineer Company: INTEC ENGINEERING SDN. BHD.
- 5. Duration: May 2002 - December 2004 PROJECT HIGHLIGHTS M4 and E11 Hub Flow assurance Steady State and Transient Studies: Produced Steady state flow assurance report covering areas such as line sizing and liquid management. Provided screening information for the M4 flow induced pulsation studies. CLIENT: SHELL SARAWAK SDN.BHD. Adani Port Marine Terminal Project: Performed Liquid pressure surge analysis for various operating scenarios associated with the SPM Offloading System and produced a technical note. ONGC G-1 and GS-15 Integrated Field Development: Produced FEED Steady State Flow Assurance report for this deepwater subsea development and presented the key findings to the client. Produced Operating and Control Philosophy for the Subsea tie-back and supervised the process facility design for the GS-15 monopod. Participated in the EPC bid evaluations and provided responses to flow assurance related Technical bid clarifications. CLIENT: ONGC Talisman Northern Field Development Project: Performed Line sizing calculations and estimated Ramp-up surge volumes for various scenarios using the Modified Cunliff method. Talisman PM3 Pipeline System Operating Manual: I was responsible for the development of Pigging, Inspection and Maintenance procedures and Pipeline System Start-up, Shutdown and Operating Philosophy. I was required to review SAFE Charts and provide input to the Operating Manual. Talisman FSO project: Produced technical note for boiler fuel gas demand and tank heating steam demand and performed requisite calculations. CLIENT: TALISMAN ENERGY SDN. BHD. Sumandak and MLTTB Projects: Determined optimal line sizes taking into consideration available pressure drop, flow stability issues and liquid surge volumes for various operating modes thru field life SPM and Pipeline Project: Performed Hydraulic Studies to size offloading pumps aboard the tanker and the pipeline to the tank farm. Pressure surge calculations were performed to
- 6. establish MAIPs and identify whether surge attenuation devices were required. Produced pump datasheet and general specification. CLIENT: MAOMING KING PETROLEUM Petrodar Melut Basin Marine Terminal Project: Overall responsible for all project related process engineering deliverables, inter-disciplinary interface requirements and Vendor co- ordination. I performed Hydraulic studies for a Waxy Crude (Non-Newtonian flow) Tanker Loading system and produced a Technical Note. I produced Process Datasheets for Export Pumps, Atmospheric storage tanks and functional specifications for the Marine Terminal Utility systems such as the hot oil system, Wax management system, Fire water system, Heat tracing, Fuel Oil treatment and Water treatment systems and power generation etc. CLIENT: PETRONAS CARIGALI SDN.BHD. Bunga Kertas FPSO Project: Coordinated FEED and Detailed Design for the Topsides Process Facility. I was responsible for the Condensate Export and Firewater System design, including the production of design philosophies, calculations, datasheets and UFDs/P&IDs. I reviewed specifications for the TEG Dehydration Package/Waste Heat Recovery Unit/Turbo Compressors/Generators and Production Separators was involved in the Technical Bid Evaluation for the TEG Dehydration Package and Production Facility EPC contractor bid submissions. I prepared a preliminary cost estimate for the FPSO Topsides Production Facilities and managed the HAZOP, Design Safety Case and QRA Studies for the FPSO. I was also required to provide Technical advice on the validity of Variation Orders and provided Topsides Contract related input to Close-Out report. CLIENT: MALAYSIA INTERNATIONAL SHIPPING CORPORATION SDN.BHD. Aban PY-3 Gas Utilisation Feasibility Study: Evaluated the basic processes for NGL recovery and performed a screening study to ascertain techno-economic feasibility. Produced cost/weight/space estimates for the recommended process/utility system and a feasibility report. CLIENT: ABAN OFFSHORE LIMITED. Title: Process/ Flow Assurance Engineer Company: Zee Engineering Consultants Duration: February 1997- April 2002 PROJECT HIGHLIGHTS Worked on a plethora of projects for Oil majors such as CONOCO INDONESIA INC. Ltd., REPSOL-YPF-MAXUS and TOTAL INDONESIE. The responsibilities included Thermo-
- 7. hydraulic line sizing for flowlines/pipelines, Offshore process equipment design, flare, vent and drain system design, produced water treatment and disposal system design, fire water system design and HAZID/HAZOP/FMEA participation. The projects worked on are listed below: • BA 20/21 Pipeline Replacement Project • SBU As-Built Drawing Update Project • Belida Field PHA Study • Poleng Gathering Network Optimisation Project • Belida Field As-Built Documentation Project • AW Platform/ORF debottlenecking Project • Handil Air Injection Project • SES Central Area Pressure Reduction Project • Flare and Relief System design for Maersk Oil Jack-up Rig • Bukaka and Palm Oil Shuttle tanker Heating System adequacy calculation • Poleng Reactivation Project • Modification of Oil processing system and Skimmer pile design for Widuri P Platform • Conceptual Design for Wunut gas processing facilities