01 - networking basics notes
- 1. Vision Infosystems (VIS) Page No. : 1 Chapter Network Basics Topics Covered What is Network? Types of network topologies Network components Types of Network 1
- 2. Vision Infosystems (VIS) Page No. : 2 Network Basics A network consists of two or more network devices like computers that are connected in order to share resources like files, folders, printers, etc. A network is linked through cables, telephone lines, radio waves, satellites, or infrared light beams. A computer based network is divided into 3 categories: 1. Local Area Network (LAN) 2. Metropolitan Area Network (MAN) 3. Wide Area Network (WAN) Local Area Network : A Local Area Network (LAN) is a network that is restricted to a relatively small area. It is generally limited to a geographic area such as a building, campus, etc. In a typical LAN network, computers are group using physical topology like BUS, STAR, RING, MESH, etc. Devices on LAN network uses Ethernet adapter for communication with each other. LAN is normally restricted from 100 to 500 meters. Metropolitan Area Network : A Metropolitan Area Network (MAN) covers larger geographic areas, such as cities, areas, etc. By interconnecting smaller networks within a large geographic area, information is easily disseminated throughout the network. MAN is normally used by companies or organizations have multiple locations for business. MAN uses long distance technologies like broadband for communication.
- 3. Vision Infosystems (VIS) Page No. : 3 Wide Area Network : Wide Area Networks (WANs) connect larger geographic areas, such as states, countries, etc. WAN too is used by multinational companies, organizations, etc. Internet can be a part of WAN network. To users, however, a WAN is similar to MAN network. Networking Components Networking Components includes all equipments that are needed to perform data-processing and communications within the network like NIC, HUB, Switch, etc. Network Interface Cards : The network interface card (NIC) provides the physical connection between the network and the computer workstation. NICs are normally used in LAN topologies like BUS, STAR, RING, etc. Now-a-days NIC provides speed at rate of 10/100/100 mbps and works at full/half duplex.
- 4. Vision Infosystems (VIS) Page No. : 4 HUB : It is multi port repeater that provides a central point of connection to all network devices like clients, servers and other devices. HUB is used in star topology using twisted pair cables. HUB works at layer 1 of OSI model. HUB uses broadcast method for packet forwarding. HUB does not maintain MAC table for efficient frame forwarding. Switch : Swtich is a layer 2 device that provides a central connection point for network devices like workstations, servers, and peripherals. Used in star topology, twisted-pair wire is run from each workstation to a central switch/hub. Switches are more intelligent then HUBs as switches maintain MAC table for efficient frame forwarding. Repeaters : Since a signal loses strength as it passes along a cable, it is often necessary to boost the signal with a device called a repeater. The repeater electrically amplifies the signal it receives and rebroadcasts it. Repeaters can be separate devices or they can be incorporated into a concentrator. They are used when the total length of your network cable exceeds the standards set for the type of cable being used. Bridges : A bridge is a device that allows you to segment a large network into two smaller, more efficient networks. If you are adding to an older wiring scheme and want the new network to be up-to-date, a bridge can connect the two. Routers : A router is a layer 3 device which helps to connect two or more routed network. It is an intelligent device use for packet forwarding. Routers select the best path to route a message, based on the destination address and origin. Cables : Cable is the medium through which information or data moves from one network device to another. There are different types of cable used with LAN, WAN and MAN. Below are the list of different types of cables available. 1) Unshielded Twisted Pair (UTP) Cable : Twisted pair cabling comes in two varieties: shielded and unshielded. Unshielded twisted pair (UTP) is the most popular and is generally the best option for school networks.
- 5. Vision Infosystems (VIS) Page No. : 5 The quality of UTP may vary from telephone-grade wire to extremely high-speed cable. The cable has four pairs of wires inside the jacket. Each pair is twisted with a different number of twists per inch to help eliminate interference from adjacent pairs and other electrical devices. The EIA/TIA (Electronic Industry Association/Telecommunication Industry Association) has established standards of UTP and rated five categories of wire. Categories of Unshielded Twisted Pair Type Use Mhz Category 1 Voice Only (Telephone Wire) Audio Frequency Category 2 Data to 4 Mbps (LocalTalk) 1.5 Mhz Category 3 Data to 10 Mbps (Ethernet) 16 Mhz Category 4 Data to 20 Mbps (16 Mbps Token Ring) 20 Mhz Category 5 Data to 100 Mbps (Fast Ethernet) 100 Mhz Category 6 Data to 155 Mbps (Fast Ethernet) 250 Mhz Category 7 Data to 1000 Mbps (Gigabit Ethernet) 600 Mhz Straight cable : It uses same color pattern on both the ends. Straight cable is used to connect two dissimilar devices like HUB/Switch and PC, or Router and HUB/Switch. Straight cables A end B end Pin 1 White/Orange Pin 1 White/Orange Pin 2 Orange Pin 2 Orange Pin 3 White/Green Pin 3 White/Green
- 6. Vision Infosystems (VIS) Page No. : 6 Pin 4 Blue Pin 4 Blue Pin 5 White/Blue Pin 5 White/Blue Pin 6 Green Pin 6 Green Pin 7 White/Brown Pin 7 White/Brown Pin 8 Brown Pin 8 Brown Cross over cable : It uses different color pattern on both the ends. Cross over cable is used to connect two similar devices like HUB/Switch and HUB/Switch, or Router and Router, PC to PC. Cross over cable A end B end Pin 1 White/Orange Pin 1 White/Green Pin 2 Orange Pin 2 Green Pin 3 White/Green Pin 3 White/Orange Pin 4 Blue Pin 4 Blue Pin 5 White/Blue Pin 5 White/Blue Pin 6 Green Pin 6 Orange Pin 7 White/Brown Pin 7 White/Brown Pin 8 Brown Pin 8 Brown RJ Connector : The standard connector for unshielded twisted pair cabling is an RJ-45 connector. This is a plastic connector that looks like a large telephone-style connector. A slot allows the RJ-45 to be inserted only one way. RJ stands for Registered Jack, implying that the connector follows a standard borrowed from the telephone industry. This standard designates which wire goes with each pin inside the connector. RJ-45 pin-out Contact 10Base-T 100Base-TX 100Base-T4 1000Base-T 1 TD+ TD+ TX_D1+ BI_DA+ (Bidi Data) 2 TD- TD- TX_D1- BI_DA- (Bidi Data) 3 RD+ RD+ RX_D2+ BI_DB+ (Bidi Data) 4 Not used Not used BI_D3+ (Bidi Data) BI_DC+ (Bidi Data) 5 Not used Not used BI_D3- (Bidi Data) BI_DC- (Bidi Data)
- 7. Vision Infosystems (VIS) Page No. : 7 6 RD- RD- RX_D2- BI_DB- (Bidi Data) 7 Not Used Not Used BI_D4+ (Bidi Data) BI_DD+ (Bidi Data) 8 Not Used Not Used BI_D4- (Bidi Data) BI_DD- (Bidi Data) 3) Shielded Twisted Pair (STP) Cable : A disadvantage of UTP is that it may be susceptible to radio and electrical frequency interference. Shielded twisted pair (STP) is suitable for environments with electrical interference; however, the extra shielding can make the cables quite bulky. Shielded twisted pair is often used on networks using Token Ring topology. 4) Coaxial Cable : Coaxial cabling has a single copper conductor at its center. A plastic layer provides insulation between the center conductor and a braided metal shield. The metal shield helps to block any outside interference from fluorescent lights, motors, and other computers. Although coaxial cabling is difficult to install, it is highly resistant to signal interference. In addition, it can support greater cable lengths between network devices than twisted pair cable. The two types of coaxial cabling are thick coaxial and thin coaxial. 4) Coaxial Cable Connectors : The most common type of connector used with coaxial cables is the Bayone-Neill-Concelman (BNC) connector. Different types of adapters are available for BNC connectors, including a T-connector, barrel connector, and terminator. Connectors on the cable are the weakest points in any network. To help avoid problems with your network, always use the BNC connectors that crimp, rather than screw, onto the cable. 5) Fiber Optic Cable : Fiber optic cabling consists of a center glass core surrounded by several layers of protective materials. It transmits light rather than electronic signals eliminating the problem of electrical interference. This makes it ideal for certain environments that contain a large amount of electrical interference. It has also made it the standard for connecting networks between buildings, due to its immunity to the effects of moisture and lighting. Fiber optic cable has the ability to transmit signals over much longer distances than coaxial and twisted pair. It also has the capability to carry information at vastly greater speeds. This capacity broadens communication possibilities to include services such as video conferencing and interactive services. The cost of fiber optic cabling is comparable to copper cabling; however, it is more difficult to install and modify. 10BaseF refers to the specifications for fiber optic cable carrying Ethernet signals.
- 8. Vision Infosystems (VIS) Page No. : 8 Facts about fiber optic cables: • Outer insulating jacket is made of Teflon or PVC. • Kevlar fiber helps to strengthen the cable and prevent breakage. • A plastic coating is used to cushion the fiber center. • Center (core) is made of glass or plastic fibers. 6) Fiber Optic Connector : The most common connector used with fiber optic cable is an ST connector. It is barrel shaped, similar to a BNC connector. A newer connector, the SC, is becoming more popular. It has a squared face and is easier to connect in a confined space. Ethernet Cable Summary Specification Cable Type Maximum length 10BaseT Unshielded Twisted Pair 100 meters 10Base2 Thin Coaxial 185 meters 10Base5 Thick Coaxial 500 meters 10BaseF Fiber Optic 2000 meters 100BaseT Unshielded Twisted Pair 100 meters 100BaseTX Unshielded Twisted Pair 220 meters Network Types The most common network types are: 1. Ethernet 2. Token Ring 3. FDDI 4. ATM
- 9. Vision Infosystems (VIS) Page No. : 9 Ethernet : The Ethernet protocol is by far the most widely used. Ethernet uses an access method called CSMA/CD (Carrier Sense Multiple Access/Collision Detection). This is a system where each computer listens to the cable before sending anything through the network. If the network is clear, the computer will transmit. If some other node is already transmitting on the cable, the computer will wait and try again when the line is clear. Sometimes, two computers attempt to transmit at the same instant. When this happens a collision occurs. Each computer then backs off and waits a random amount of time before attempting to retransmit. With this access method, it is normal to have collisions. However, the delay caused by collisions and retransmitting is very small and does not normally effect the speed of transmission on the network. The Ethernet protocol allows for linear bus, star, or tree topologies. Data can be transmitted over twisted pair, coaxial, or fiber optic cable at a speed of 10 Mbps up to 1000 Mbps. Fast Ethernet : To allow for an increased speed of transmission, the Ethernet protocol has developed a new standard that supports 100 Mbps. This is commonly called Fast Ethernet. Fast Ethernet requires the use of different, more expensive network concentrators/hubs and network interface cards. In addition, category 5 twisted pair or fiber optic cable is necessary. Fast Ethernet is becoming common in schools that have been recently wired. Gigabit Ethernet : The most recent development in the Ethernet standard is a protocol that has a transmission speed of 1 Gbps. Gigabit Ethernet is primarily used for backbones on a network at this time. In the future, it will probably be used for workstation and server connections also. It can be used with both fiber optic cabling and copper. The 1000BaseTX, the copper cable used for Gigabit Ethernet, is expected to become the formal standard in 1999. Token Ring : The Token Ring protocol was developed by IBM in the mid-1980s. The access method used involves token-passing. In Token Ring, the computers are connected so that the signal travels around the network from one computer to another in a logical ring. A single electronic token moves around the ring from one computer to the next. If a computer does not have information to transmit, it simply passes the token on to the next workstation. If a computer wishes to transmit and receives an empty token, it attaches data to the token. The token then proceeds around the ring until it comes to the computer for which the data is meant. At this point, the data is captured by the receiving computer. The Token Ring protocol requires a star-wired ring using twisted pair or fiber optic cable. It can operate at transmission speeds of 4 Mbps or 16 Mbps. Due to the increasing popularity of Ethernet, the use of Token Ring in school environments has decreased. FDDI : Fiber Distributed Data Interface (FDDI) is a network protocol that is used primarily to interconnect two or more local area networks, often over large distances. The access method used by FDDI involves token-passing. FDDI uses a dual ring physical topology. Transmission normally occurs on one of the rings; however, if a break occurs, the system keeps information moving by automatically using portions of the second ring to create a new complete ring. A major advantage of FDDI is speed. It operates over fiber optic cable at 100 Mbps. ATM : Asynchronous Transfer Mode (ATM) is a network protocol that transmits data at a speed of 155 Mbps and higher. ATM works by transmitting all data in small packets of a fixed
- 10. Vision Infosystems (VIS) Page No. : 10 size; whereas, other protocols transfer variable length packets. ATM supports a variety of media such as video, CD-quality audio, and imaging. ATM employs a star topology, which can work with fiber optic as well as twisted pair cable. . ATM is most often used to interconnect two or more local area networks. It is also frequently used by Internet Service Providers to utilize high-speed access to the Internet for their clients. As ATM technology becomes more cost-effective, it will provide another solution for constructing faster local area networks. Summary of Network type Network Type Cable Speed Topology Ethernet Twisted Pair, Coaxial, Fiber 10 Mbps Linear Bus, Star, Tree Fast Ethernet Twisted Pair, Fiber 100 Mbps Star Token Ring Twisted Pair 4 Mbps - 16 Mbps Star-Wired Ring FDDI Fiber 100 Mbps Dual ring ATM Twisted Pair, Fiber 155-2488 Mbps Linear Bus, Star, Tree