09_-_General Engineering_2_-_General.ppt

General Engineering Knowledge
Part 1
Construction Materials

Construction Materials
• Most commercial vessels, and a lot of their
equipment, are constructed of iron and it’s
alloys.
• Other common materials found onboard
include aluminium, copper and it’s alloys,
plastics, and resins

Iron
• Iron is the most abundant element found on
Earth.
• Iron accounts for roughly 95% of all worldwide
metal production.
• Iron is:
– Relatively cheap
– Relatively strong
– Relatively soft
• Iron is usually alloyed with one or more other
elements to improve it’s working properties.

Cast Iron
• Cast Iron is an alloy containing between 2~4% Carbon,
and 1~4% Silicon.
• Cast Iron:
– Tends to be brittle
– Has a low melting point
– Has good fluidity and castability
– Has excellent machinability
– Has excellent resistance to wear and deformation
• Cast Iron is often used for:
– Engine blocks and heads
– Pump and valve bodies
• Because of the relatively high Carbon content, Cast Iron
is difficult to weld.

(Carbon) Steel
• Steel is an Iron alloy containing up to 2% Carbon.
• The higher the Carbon content, the harder and more
brittle the Steel becomes.
• Carbon content:
– 0.05~0.15% - Low Carbon Steel – Nails, pipe, rivets, stampings
– 0.16~0.29% - Mild Carbon Steel – Structural & machine parts
– 0.30~0.59% - Medium Carbon Steel – Gears, shafts, axles
– 0.60~0.99% - High Carbon Steel – Tools, springs
– 1~2% - Ultra High Carbon Steel – Drills, knives, saws, files
• Steel may also contain small amounts of manganese,
silicon, and copper.

Stainless Steel
• Stainless Steel is an Iron alloy containing at least 10% Chromium –
18% is common.
• Most Stainless Steels contain between 0.05% and 0.15% Carbon.
• Most Stainless Steels contain between 5% and 20% Nickel.
• Stainless Steel is available in different series. The 300 series
accounts for over 70% of Stainless Steel production.
• Most Stainless Steel found on ships is either:
– 304 - 18% Cr, 8% Ni (sometimes called 18/8 or 18-8)
– 316 - 18% Cr, 10% Ni (sometimes called 18/10 or 18-10)
• Stainless Steel does oxidize (rust), but when it does the Chromium
content forms a thin passivation layer of Chromium Oxide which
protects the rest of the material from oxidizing further.
• Nickel assists in the formation of the passivation layer – higher
nickel alloys are used in environments with lower oxygen contents
(ie: underwater).

Non-Ferrous Metals
• Non-Ferrous Metals do not contain an
appreciable amount of Iron.
• Some common Non-Ferrous Metals found
aboard include:
– Copper
– Aluminium
– Zinc

Copper
• Copper is a corrosion resistant, ductile (soft) element that has high
thermal and electrical conductivity.
• Copper oxidizes in air and forms a protective layer of Copper Oxide
which protects the rest of the material.
• Copper is often used for fuel and water lines aboard ships, due to its
corrosion resistance.
• Electrical wiring is made of Copper, due to its high electrical
conductivity.
• Copper is often alloyed with other elements to create Brass and
Bronze.
• Excessive levels of Copper are toxic. Copper is a common
ingredient in anti-fouling paint, and it became popular in the 16th
century to cover the hulls of wooden ships in copper plating in order
to reduce marine growth.

Brass
• Brass is a Copper alloy that usually contains 30~40%
Zinc (Zn).
• Brass is stronger and harder then pure Copper.
• Some common Brasses include:
– Yellow Brass - 35% Zn - Most common, general hardware and
decoration
– Naval Brass - 39% Zn, 1% Sn - Stronger, greater corrosion
resistance
– Muntz Metal - 40% Zn - Greater corrosion resistance,
– Free-Cutting Brass - 35% Zn, 2% Pb - Gears, screws, bolts
– Red Brass - 5% Zn, 5% Sn, 5% Pb - Castings
– Aluminium Brass - 30% Zn, 2% Al – extremely corrosion
resistant, heat exhangers, condensor tubing

Bronze
• Bronze is a Copper alloy that usually
contains 10~20% Tin (Sn).
• Bronze is extremely hard and very
corrosion resistant.
• Bronze has excellent low-friction
properties, and is often used for
bearings.
• One common type is Phosphor Bronze,
which contains 10% Sn & 1% P.
Phosphor Bronze is often used to make
propellers and shafts.

Nickel
• Nickel is often alloyed with Copper.
• Cupronickel is an alloy that usually contains 25~50%
Nickel (Ni).
– Cupronickel’s electrical potential is neutral in regards to
seawater, and therefore it is extremely corrosion resistant in a
marine environment.
– Cupronickel often contains trace amounts of Manganese or Iron
to strengthen it.
– Cupronickel is often used for heat exchangers and valves.
• Monel is an alloy that usually contains 50~75% Nickel.
– Monel is one of the most corrosion resistant metals available,
excluding precious metals (Platinum, Gold, Silver…).
– Monel often contains trace amounts of Iron or Titanium to
strengthen it.
– Monel is often used to heat exchangers, valves and pump shafts
in corrosive environments, as well as keel bolts on wooden or
fiberglass boats.

Aluminium
• Aluminium is a soft, durable and lightweight metal.
• Aluminium oxidizes in air and forms a protective layer of
Aluminium Oxide which protects the rest of the material.
• Aluminium has roughly 1/3rd of the weight and stiffness
of steel.
• Aluminium can be easily machined, cast, and extruded.
• Although fairly corrosion resistant on its own, Aluminium
can be very prone to galvanic corrosion when it is in
electrical contact with a second metal.
• Aluminium is often used for hulls and superstructures on
ships where weight is a concern, as well as hatches,
ladders, and railings.

Zinc
• Zinc is not useful as a structural material due to
its low strength and low melting temperature.
• Zinc has two main marine applications:
– Galvanization – Iron or Steel is coated with Zinc to
form a barrier that will protect it from corrosion.
– Sacrificial Anodes – Zinc ingots are attached to other
metals to protect them from galvanic corrosion. The
Zinc is slowly eaten away, and must be replaced
periodically.
• As previously mentioned, Zinc is often alloyed
with Copper to make Brass.

Plastics and Resins
• Most Plastics and Resins are cheap, relatively
strong, and extremely corrosion resistant.
• Some smaller boats have hulls and/or
superstructures made of Plastics and Resins.
• Due to their low-friction properties, some
Plastics and Resins are used as low speed
bearings on propeller and rudder shafts.

Corrosion
• Corrosion means the breaking down of essential
properties in a material due to chemical reactions with its
surroundings.
• Corrosion can be concentrated locally to form a pit or
crack, or it can extend across a wide area to produce
general deterioration.
• Two common kinds of corrosion in the marine
environment include:
– Passivation Corrosion: occurs when the oxide layer protecting
the base metal (such as Copper, Stainless Steel, and Aluminium)
is scratched or otherwise damaged. This typically creates a pit
or crack.
– Galvanic Corrosion: is an electrochemical process in which one
metal corrodes preferentially when in electrical contact with a
different type of metal, and both metals are immersed in an
electrolyte (such as water). This typically creates general
surface deterioration

Galvanic Series
• Nobel (cathodic)
– Platinum
– Gold
– Graphite
– Titanium
– Silver
– Stainless steels
– Nickel
– Monel
– Cupronickel
– Bronze
– Brass
– Copper
– Cast iron
– Steel
– Aluminium
– Zinc
– Magnesium
• Active (Anodic)
• When two dissimilar metals in electrical
contact are placed in an electrolyte, the
metal which is lower on this list will
corrode preferentially.
• The farther apart the two metals are, the
higher the risk of galvanic corrosion.

Preventing Corrosion
• Corrosion can be prevented by:
– Forming a barrier coating (such as paint) to
protect the metal from the environment
– Using sacrificial anodes of Zinc or Magnesium
which will corrode preferentially
• Eliminating any stray electrical currents
will help reduce corrosion.
• Using dissimilar metals should be avoided
whenever possible.

Part 2
Fire Hazards

Fire Hazards
• Classes of Fires:
– “A” – “Ashes” – ordinary combustibles such as wood,
cloth, and rubber.
– “B” – “Barrels of Oil” – flammable liquid or gaseous
fuels such as diesel or propane.
– “C” – “Conductivity” – fires involving potentially live
electrical equipment, such as short-circuiting
machinery or overloaded electrical cables.
– “D” – fires involving burning metals, such as
magnesium flares.

Flash Point
• The flash point of a flammable liquid is the lowest
temperature at which it can form an ignitable mixture in
air. At this temperature the vapour may cease to burn
when the source of ignition is removed.
• The fire point, a slightly higher temperature then the
flash point, is defined as the temperature at which the
vapour continues to burn after being ignited.
• The auto-ignition temperature of a substance is the
lowest temperature at which it will spontaneously ignite
in a normal atmosphere without an external source of
ignition, such as a flame or spark.

Flash Points of Common Fuels
• Fuel – Flash point (auto-ignition temp)
– Gasoline −40°C (246°C)
– Diesel 62°C (210°C)
– Kerosene 72°C (220°C)
• Because Diesel has a considerably higher
flashpoint then Gasoline, Diesel is the
preferred fuel for use onboard ships.

Spontaneous Combustion
• Spontaneous Combustion is a type of combustion which
occurs without an external ignition source.
• How Spontaneous Combustion occurs:
1. A substance with a relatively low ignition temperature begins
to release heat, which may occur in several ways, such as
oxidation or fermentation.
2. The heat is unable to escape, and the temperature of the
material rises.
3. The temperature of the material rises above its ignition point.
4. Combustion begins, if sufficient oxygen is present.
• The most common example of spontaneous combustion
is a pile of oily rags left in the corner. The oil oxidizes,
creating heat. If the heat is unable to dissipate, the rags
will start to burn.

Heat Shields and Lagging
• Heat Shields and Lagging are placed on hot
surfaces such as exhaust piping in order to:
– Protect personnel from burns.
– In the event of a flammable fluid leak or spill, to stop
the fluid from coming into contact with a hot surface
and igniting.
• High pressure fuel lines on engines are often
doubled. If the inner fuel line should burst, the
fuel is contained in the outer line and allowed to
run off to a safe location.

Flammable Material Storage
• Flammable Materials such as
paint, thinner, oils, and
greases should be stored in a
dedicated non-combustible
locker that is not located in an
accommodation or machinery
space.
• A smoke alarm should be fitted
in this space.

Fuel Tank Vents
• Fuel tank vents normally terminate on the
weather deck.
• Shutoff valves are fitted at the termination
point, as well as a fire screen (a fine
gauge wire mesh to prevent the entry of
flames into the tank).

Engine Room Fire Prevention
• The engine room should be kept as clean
as possible in order to reduce the chance
of fire.
• All machinery and systems should be
inspected regularly for leaks or damage.
• The engine room bilge should be kept free
of fuel and oil.
• Garbage such as oily rags or used filters
should be disposed of properly.

Re-Fuelling (Bunkering)
Operations
• All pumps and hoses should be approved for the
product being transferred.
• An effective method of communication must be
established so that the flow of fuel can be
stopped immediately if needed.
• Scuppers and Freeing Ports should be plugged
so that any spill can be contained.
• All sources of ignition in the vicinity, such as
cigarettes or naked lights, should be
extinguished.

Fire Hazards
• List ten common stores found onboard
that may create a fire hazard.
• How could the risk of fire be reduced?
• If a fire were to develop, how could it be
fought?

Structural Fire Protection
• Divisions:
– “A” – A stiffened bulkhead or deck capable of preventing the passage of smoke
and flame when subjected to the standard fire test for a period of 60 minutes.
– “B” – A division formed by a bulkhead, ceiling or lining that is constructed so as to
be capable of preventing the passage of flame when subjected to the standard
fire test for 30 minutes.
– “C” – A division that is constructed of non-combustible materials.
• Insulation:
– “-60” – Insulation that will prevent the opposite face from reaching an average
temperature greater then 150°C for 60 minutes.
– “-0” – No insulation
• Examples:
– “A-60” – Deckhead on a passenger vessel.
– “B-15” – Crew cabin door on a cargo vessel.

Fire Doors
• Fire doors are fitted onboard ships to stop or
slow the spread of fire, heat, and smoke.
• Guides, bearings, hinges, latches, pulleys and
other moving parts should be lubricated
regularly.
• Seals should be checked regularly.
• Automatically closing fire doors can be closed
locally, from the bridge, or by the activation of
the fire alarm system. They should be checked
regularly for correct operation.

Watertight and Weathertight
• Watertight:
– Designed and constructed to withstand a static head of water
without any leakage.
– Refers to structures that must withstand hydrostatic loading for
extended periods of time, including the hull bottom and sides,
main deck plating, tanks, and bulkheads.
• Weathertight:
– Water will not penetrate in any sea condition.
– Refers generally to topside structures subject to occasional and
short exposure to water on deck, from boarding waves or wind
driven rain and spray.
• In short, the watertight portions of a hull generally keep
water out from below, and the weathertight portions of a
structure generally keep it out from above.

Watertight Doors
• Watertight doors are fitted in bulkheads or in the hull, to allow
passage of personnel and equipment.
• Guides, bearings, hinges, latches, pulleys and other moving
parts should be lubricated, and seals should be checked
regularly.
• On some vessels the watertight doors are capable of being
operated both locally and remotely (usually from the bridge).
Audio & visual alarms are fitted at each door to indicate that it
is about to close. Instrumentation is fitted on the bridge to
indicate:
– In which position the door is supposed to be.
– In which position the door currently is.
– Other faults such as power failures.
• Care should be taken not to linger in watertight door
openings, and to not leave any objects where they may block
a watertight door from closing correctly.

Fire (Vent) Dampers
• Fire dampers are normally fitted on the
weather deck.
• Fire dampers are used to close vents and
ducts in the event of a fire.
• Fire dampers should be lubricated and
checked for proper operation regularly.

Fire Alarm Systems
• Fixed Fire Alarm Systems normally use two
kinds of detectors:
– Smoke detectors
• Usually found in accommodation spaces
• Tested by using “fake smoke”
– Heat detectors
• Usually found in areas such as engine rooms and galleys
where a small amount of smoke is common and would create
false alarms.
• Tested by using a heat gun
• The normal alarm used to indicate a fire is a
continuous ringing of the alarm bells.

Fire Smothering Systems
• Fire smothering systems are fitted in engine rooms, and in some
galleys.
• Smothering systems are fitted with an alarm that sounds before the
smothering agent is dumped. Most alarms are comprised of a siren
that is driven by the dumped agent itself. On hearing the alarm all
personnel should immediately vacate the compartment.
• The activation point for a fire smothering system is located outside
the compartment protected, often on the bridge.
• Only the Captain has the authority to activate the system (or have it
activated).
• If possible, before activation:
– The area should be cleared of personnel
– Machinery in the compartment should be stopped
– Ventilation systems should be shut down
– Fire dampers should be closed

Sprinkler Systems
• On some vessels sprinkler systems are used to
protect accommodation and control spaces.
• Sprinkler systems may be:
– Automatic – The system is kept pressurized. When a
sprinkler head is heated above a certain temperature
it opens and water is sprayed out.
– Manual – Sprinkler heads are installed and connected
to the fire line through a manifold. To sprinkle a
compartment the fire pump is started, and the valve to
the desired compartment is opened.
• Pumps should be checked regularly for correct
operation and pressure.

Engine Room Escapes
• Every manned engine room must have at
least two exits, and at least one must lead
directly to the weather deck.
• The exits should be located, as far as
practical, at opposite ends of the engine
room.
• Engine room escapes should be kept clear
at all times.

Emergency Shutoffs
• Fuel tanks (including day-tanks)
must be fitted with a quick-closing
valve, with a remote pull located
outside the engine room.
Alternatively, valves with extended
spindles which extend to an upper
deck may be fitted.
• Engines (propulsion, gensets, etc)
should be fitted with remote
shutdowns that will allow them to be
stopped in case of emergency.
• Bilge and transfer pumps should be
fitted with remote shutdowns that will
allow them to be stopped by a
member of the deck crew if they
detect any pollutant being
discharged.

Fire Mains
• The fire main is a network of pipes that
connects the fire pumps and the fire
hoses.
• Main fire pumps are normally found in the
engine room.
• Most ships also have at least one fire
pump outside the engine room that can be
used in the event of an engine room fire.

Part 3
Safe Working Practices

Safe Working Practices:
WHMIS
• WHMIS: Workplace Hazardous Materials
Information System
• WHMIS is Canada's national hazard
communication standard.
• The key elements of the system are:
1. Cautionary labeling of containers of WHMIS
“controlled products”.
2. The provision of material safety data sheets
(MSDSs).
3. Worker education and training programs.

Safe Working Practices:
Canada Labour Code
• Part II of the Canada Labour Code relates
to occupational health and safety and
reflects the desire to reduce work place
injuries and accidents in federal
jurisdiction.
• Three Basic Rights:
– Right to Know
– Right to Participate
– Right to Refuse

Personal Protective Equipment
• Some common personal protective
equipment worn in the engine room
includes:
– Eye protection
– Ear protection
– Head protection
– Foot protection
– Skin protection
– Hand protection

Rotating Machinery
• Be very careful when working in the
vicinity of rotating machinery.
• Do not wear loose clothing.
• Remove all jewellery.
• Tie back long hair.

General Engine Room Safety
• Keep the engine room clean. Grease on the deck may
cause a fall. Tools lying around may cause a trip.
• Keep up with simple routine maintenance. Inoperative
light fixtures will reduce the ambient light level.
• Fix small problems before they develop into large
problems.
• Make sure all safety guards are in their correct place.
• Make sure all safety equipment is in its place and
functioning correctly.

Machinery Maintenance
• Before performing maintenance on any machinery:
– Notify your co-workers that you will be performing the
maintenance.
– Lock out the start circuit (remove key, disconnect start battery).
– Make sure that any and all pressure systems on the machinery
are bled off before working on them.
– Make sure that electrical power has been disconnected and
capacitors discharged before working on electrical components.
• The Manufacturer’s manual should be consulted when
performing maintenance on any machinery because it
will contain important safety information.

Hot Work (Welding, Cutting)
• When performing hot work:
– The area should be clean and free of any flammable
material.
– Fire fighting equipment should be close at hand.
– A fire watch should be posted, not only in the
compartment where the hot work is being performed,
but also on the opposite sides of any bulkheads,
decks, etc that are being worked on or near.
– The fire watch should continue for a minimum of 1
hour after the hot work is finished.

Lifting Equipment
• Lifting equipment should be inspected before
use.
• Look for:
– Corrosion
– Cracking
– Elongation
– Deformation
– Broken strands or fibres
• Never place any part of your body under an
object that has been lifted unless the object has
been blocked and/or secured.

Confined Spaces
• Generally speaking, a confined space is an enclosed or
partially enclosed space that:
– is not primarily designed or intended for human occupancy
– has a restricted entrance or exit by way of location, size or
means
– Can represent a risk for the for the health and safety of anyone
who enters, due to one or more of the following factors:
• its design, construction, location or atmosphere
• the materials or substances in it
• work activities being carried out in it, or the
• mechanical, process and safety hazards present
• Before entering into a confined space:
– Have a spotter watch you
– Wear proper personal protection
– Have the atmosphere tested
– Make sure any and all safety equipment is on site.

Part 4
Pollution Prevention

Regulations for the Prevention of
Pollution from Ships and for
Dangerous Chemicals
• Part of the Canadian Shipping Act
• Types of pollution:
– Oil
– Noxious Liquid Substances and Dangerous
Chemicals
– Sewage
– Garbage
– Air
– Anti-Fouling Systems

Pollution Prevention Terms
• ppm: parts per million, by volume.
• Garbage: all kinds of victual, domestic and operational waste that
are generated during the normal operation of a ship and are liable to
be disposed of continuously or periodically, excluding fresh fish and
any of their parts. This definition includes plastics, dunnage, lining
and packing materials, food wastes and refuse such as paper
products, rags, glass, metal, bottles, crockery, incinerator ash and
cargo residues.
• Sludge: sludge from the fuel or lubricating oil separators, waste
lubricating oil from main or auxiliary machinery, or waste oil from
bilge water separators, oil filtering equipment or drip trays.
• Oily substance: a substance with any oil content.
• Sewage:
– human body wastes and wastes from other living animals;
– drainage and other wastes from toilets and other receptacles intended
to receive or retain human body wastes;
– drainage from medical premises such as a dispensary or a sick bay via
wash basins, wash tubs and scuppers located in such premises;
– drainage from spaces containing living animals.
• Transfer operation: the loading or unloading of oil, an oily mixture, a
noxious liquid substance or a dangerous chemical to or from a ship,
a loading facility, or another ship; or

Oil Record Book
• Carried by ships >400GT (and tankers >150GT)
• To be filled out when:
– Ballasting or cleaning fuel tanks
– Discharging dirty ballast or cleaning water from fuel
tanks
– Disposing oily residues and sludge
– Discharging overboard bilge water which has
accumulated in machinery spaces
• To include:
– Which tank/bilge
– Substance that was discharged or disposed of
– Quantity of substance discharged or disposed of
– Ship’s position

Emergency Polluting
• A Vessel is permitted to discharge a pollutant when:
– a discharge is necessary for the purpose of saving lives, securing the
safety of a ship or preventing the immediate loss of a ship;
– a discharge occurs as a result of an accident of navigation in which a
ship or its equipment is damaged, unless the accident occurs as a result
of an action that is outside the ordinary practice of seamen;
– minimal and unavoidable leakage of oil occurs as a result of the
operation of an underwater machinery component;
– a discharge is made for the purpose of scientific research into pollution
abatement or control in accordance with permission granted by the
Minister;
– an accidental loss of synthetic fishing nets occurs, provided that all
reasonable precautions were taken to prevent the loss;
– a discharge of garbage results from damage to a ship or its equipment,
provided all reasonable precautions have been taken before and after
the occurrence of the damage to prevent or minimize the discharge;
– an emission involving pollution of the air results from damage to a ship
or its equipment, provided all reasonable precautions have been taken
before and after the occurrence of the damage to prevent or minimize
the emission

Oily-Water Separators
• An oily-water separator (OWS) is
a piece of shipboard equipment
that allows a vessel's crew to
separate oil from bilge water
before it is discharged overboard.
• The water discharged from an
OWS must contain less then
5ppm oil.
• OWS’s contain an alarm and
automatic shutdown that will stop
the discharge of water should the
concentration of oil exceed 5ppm.

Shipboard Oil Pollution Emergency Plan
(SOPEP)
• Required for ships >400GT (and tankers
>150GT)
• Provide guidance to the Master and
officers on board the ship with respect to
the steps to be taken when a pollution
incident has occurred or is likely to occur.
• Includes contact information for all
relevant personnel and agencies.

Whom to Contact in case of Pollution
1. Watch Officer
2. Captain
3. Office
4. Canadian Coast Guard
5. Transport Canada Marine Safety
6. Port Authority (if applicable)
7. Environment Canada

Part 6
Hydraulic Systems

Hydraulic Systems
• Hydraulic systems use pressurized liquid to do work.
• They can be powered by hand, or with a motor or
engine.
• In closed hydraulic circuits the fluid is returned directly to
the pump inlet after making it’s way through the circuit.
Pumps in these circuits usually turn on and off as
required. Reversible pumps are often used, negating the
need for valves.
• In open hydraulic circuits the fluid is returned to a
reservoir tank, which the pump suction is also attached
to. Pumps in these circuits usually run continuously, and
always in the same direction.

Hydraulic System Valves
• All hydraulic systems should
contain a pressure relief
valve, to protect components
from over-pressurization.
• Spool valves are often used
in hydraulic systems to allow
the hydraulic circuit to be
easily reversed.

Hydraulic System Oil
• The most common liquid used in hydraulic systems is oil,
due to it’s anti-corrosion and lubrication properties.
• Hydraulic oils are available in different viscosities, for
use in different types of systems and in different
temperatures.
• It is very important to keep hydraulic oil clean and free of
water in order to prevent corrosion, wear, and jamming
of components.
• Most hydraulic systems contain filters, and some contain
tank heaters to stop water from condensing in the
reservoirs.
• If air enters a hydraulic system it will make the controls
feel “spongy” or “mushy”, because of it’s compressible
nature. The air must be bled out to prevent erratic
operation, and to prevent damage to system
components due to cavitation.

Hydraulic System Safety
• Hydraulic systems can contain liquids compressed to
pressures exceeding 5000psi.
• In systems operating a high pressures, a small leak can
produce a small “jet” of liquid that can easily cut flesh
and bone.
• Due to both friction and compression, hydraulic systems
will produce heat. Many systems will have a cooler.
• Excessive heat indicates a problem with the system.
• A change in sound or vibration may also indicate a
problem with a hydraulic system.
• When filling a hydraulic tank or reservoir, enough room
should be left at the top to allow for the liquid to expand
as it warms up.

Part 7
Pneumatic Systems

Pneumatic Systems
• Pneumatic systems use pressurized gas to do work.
• They are usually powered with a motor or engine, but
can also be powered by hand.
• Almost all pneumatic circuits use air, and are designed
as open circuits. Air from the atmosphere is
compressed, used in the circuit, and then released back
to the atmosphere.
• Air receivers are used to store pressurized air.

Air Compressors
• Most air compressors are a piston design. They operate using the
same basic principles as a piston engine. On the down-stroke the
intake valve is open, and air is drawn into the cylinder. On the up-
stroke the exhaust valve is open and the piston pushes the air out
into the pneumatic circuit.
• Like piston engines, piston air compressors usually have lubrication
and cooling systems that must be checked and maintained regularly.
• Most air compressors use a pressure switch to start and stop
automatically in order to maintain the air pressure in a desired
range.
• Excessive running, or cycling of an air compressor is usually caused
by a leak or a faulty pressure switch.
• Many air compressors are fitted with an intercooler to reduce the
temperature of the compressed air exiting the compressor.
• Many air compressors are equipped with un-loaders to make them
easier to start. Un-loaders may also be used to stop the air
compressor from compressing air, without stopping the air
compressor itself.

Air Receivers
• All air receivers are fitted with pressure relief
valves.
• Because the atmosphere always contains some
water vapour, this is introduced into the circuit by
the air compressor. This water vapour will cool
and condense in the air receiver, and must be
drained off regularly.
• The maximum operating pressure for an air
receiver can be found on a plate attached to the
receiver.

Part 8
Watch Keeping Procedures

Contact With Home Base
• Vessels with Small Vessel Machinery
Operators (SVMOs) are required to have
continual communications available with
the home base of operations.
• The home base should be contacted
immediately whenever a system or piece
of machinery fails, or is operating outside
of it’s design limits.

Pre-Departure Checks
• Before departure, the SVMO should make a pre-
departure check that includes:
– Consumables (fuel, oil, water, etc)
– Spares (filters, belts, impellors, etc)
– Condition of equipment (machinery, battery chargers,
etc)
– Condition and availability of safety equipment
(personal protection, 1st Aid kit, fire fighting
equipment)
– Bilge levels
– The engine room logbook (previous problems and
trends)

Post-Departure Machinery Checks
• While underway, the SVMO should monitor:
– All equipment being used (temperatures, pressures,
voltages, etc)
– Consumable levels (fuel, oil, water, etc)
– Bilge levels
– Leaks (water, oil, fuel, etc)

Engine Room Logbook
• An engine room logbook is used to record
incidents and maintenance as well as
operating pressures, temperatures,
voltages, etc in order to identify trends.
• All incidents should be reported to the
Captain and home base immediately.

General Knowledge
• The amount of fuel in a tank is usually measured with a dip-stick or a
sight-glass.
• Fuel can be checked for water contamination by taking a small
sample from the sludge drain.
• Common locations for starting and stopping engine room machinery
include locally, the control room, and the bridge.
• Deck plates and walkways should always be kept secured and
clean.
• Excessive water in the bilges may reduce stability due to the free
surface effect and should be pumped out after making sure it does
not contain pollutants.
• If you suspect the vessel has touched bottom immediately inform the
bridge, close all watertight doors and hatches, and check the engine
room for damage/leaks.
• Watertight door and hatches should be kept closed when not in use
while the vessel is underway.

Situations #1
• Fire in the engine room:
– Inform the bridge.
– Attempt to extinguish the fire.
– If attempts to extinguish the fire are unsuccessful,
inform the captain that you feel it may be necessary to
use the smothering system.
• Unexpected main engine shut-down:
– Attempt to determine the cause of the shut-down,
check all fluids and levels.
– Attempt to re-start the engine.
• Loss of wheelhouse engine control:
– Prepare the engine and transmission for local control.

Situations #2
• Low main engine oil pressure alarm:
– Check oil pressure gauge.
• If low request permission to reduce speed/load.
• If nil request permission to stop engine.
– Check oil level with dip-stick.
– Check for leaks.
• High main engine jacket temperature:
– Request permission to reduce speed/load.
– Check water flow from cooling pump(s).
– Check thermostat operation.

Situations #3
• Low main engine cooling water level:
– Request permission to reduce speed/load.
– Top up engine cooling water level and continue to
monitor.
– Check for leaks.
• High engine room bilge alarm:
– Visually check bilge level.
– Pump out engine room bilge, and continue to monitor.

09_-_General Engineering_2_-_General.ppt

More Related Content

Similar to 09_-_General Engineering_2_-_General.ppt (20)

Recently uploaded (20)

09_-_General Engineering_2_-_General.ppt