5980 dual column floor frames system support

5980 Series Dual Column Floor Frames
System Support M10-16250-EN Revision H
The difference is measurable®

Electromagnetic Compatibility
Where applicable, this equipment is designed to comply with International Electromagnetic Com-
patibility (EMC) standards.
To ensure reproduction of this EMC performance, connect this equipment to a low impedance
ground connection. Typical suitable connections are a ground spike or the steel frame of a building.
Proprietary Rights Notice
This document and the information that it contains are the property of Illinois Tool Works Inc.
(ITW). Rights to duplicate or otherwise copy this document and rights to disclose the document and
the information that it contains to others and the right to use the information contained therein may
be acquired only by written permission signed by a duly authorized officer of ITW.
Trademarks
Instron®
is a registered trademark of Illinois Tool Works Inc (ITW). Other names, logos, icons, and
marks identifying Instron products and services referenced herein are trademarks of ITW and may
not be used without the prior written permission of ITW.
Other product and company names used herein are trademarks or trade names of their respective
companies.
Original Instructions
© Copyright 2009 Illinois Tool Works Inc. All rights reserved. All of the specifications
shown in this document are subject to change without notice.
Worldwide Headquarters
Instron
825 University Avenue
Norwood, MA 02062-2643
United States of America
European Headquarters
Instron
Coronation Road
High Wycombe, Bucks HP12 3SY
United Kingdom
Industrial Products Group
Instron
900 Liberty Street
Grove City, PA 16127
United States of America

iii
Preliminary Pages
Product Support: www.instron.com
General Safety Precautions
Materials testing systems are potentially hazardous.
Materials testing involves inherent hazards from high forces, rapid motions, and stored
energy. You must be aware of all moving and operating components in the testing system
that are potentially hazardous, particularly force actuators or a moving crosshead.
Carefully read all relevant manuals and observe all Warnings and Cautions. The term
Warning is used where a hazard may lead to injury or death. The term Caution is used
where a hazard may lead to damage to equipment or to loss of data.
Instron products, to the best of its knowledge, comply with various national and
international safety standards, in as much as they apply to materials and structural
testing. We certify that our products comply with all relevant EU directives (CE mark).
Because of the wide range of applications with which our instruments are used, and over
which we have no control, additional protection devices and operating procedures may
be necessary due to specific accident prevention regulations, safety regulations, further
EEA directives or locally valid regulations. The extent of our delivery regarding
protective devices is defined in your initial sales quotation. We are thus free of liability
in this respect.
At your request, we will gladly provide advice and quotations for additional safety
devices such as protective shielding, warning signs or methods of restricting access to
the equipment.
The following pages detail various general warnings that you must heed at all times
while using materials testing equipment. You will find more specific Warnings and
Cautions in the text whenever a potential hazard exists.
Your best safety precautions are to gain a thorough understanding of the equipment by
reading your instruction manuals and to always use good judgement.
It is our strong recommendation that you should carry out your own safety risk
assessment on the use of the test system, test methods employed, specimen loading and
specimen behavior at failure.

Preliminary Pages
iv M10-16250-EN
Warnings
Crush Hazard - Allow only one person to handle or operate the system at all times.
Operator injury may result if more than one person operates the system. Before working
inside the hazard area between the grips or fixtures, ensure that no other personnel can
operate the computer or any of the system controls.
Crush Hazard - Take care when installing or removing a specimen, assembly,
structure, or load string component.
Installation or removal of a specimen, assembly, structure, or load string component
involves working inside the hazard area between the grips or fixtures. Keep clear of the
jaws of a grip or fixture at all times. Keep clear of the hazard area between the grips or
fixtures during actuator or crosshead movement. Ensure that all actuator or crosshead
movements necessary for installation or removal are slow and, where possible, at a low
force setting.
Hazard - Press the Emergency Stop button whenever you consider that an unsafe
condition exists.
The Emergency Stop button removes hydraulic power or electrical drive from the testing
system and brings the hazardous elements of the system to a stop as quickly as possible.
It does not isolate the system from electrical power, other means are provided to
disconnect the electrical supply. Whenever you consider that safety may be
compromised, stop the test using the Emergency Stop button. Investigate and resolve the
situation that caused the use of the Emergency Stop button before you reset it.
Flying Debris Hazard - Make sure that test specimens are installed correctly in
grips or fixtures in order to eliminate stresses that can cause breakage of grip
jaws or fixture components.
Incorrect installation of test specimens creates stresses in grip jaws or fixture components
that can result in breakage of these components. The high energies involved can cause
the broken parts to be projected forcefully some distance from the test area. Install
specimens in the center of the grip jaws in line with the load path. Insert specimens into
the jaws by at least the amount recommended in your grip documentation. This amount
can vary between 66% to 100% insertion depth; refer to supplied instructions for your
specific grips. Use any centering and alignment devices provided.
Hazard - Protect electrical cables from damage and inadvertent disconnection.
The loss of controlling and feedback signals that can result from a disconnected or
damaged cable causes an open loop condition that may drive the actuator or crosshead
rapidly to its extremes of motion. Protect all electrical cables, particularly transducer
cables, from damage. Never route cables across the floor without protection, nor suspend
cables overhead under excessive strain. Use padding to avoid chafing where cables are
routed around corners or through wall openings.

v
Preliminary Pages
High/Low Temperature Hazard - Wear protective clothing when handling
equipment at extremes of temperature.
Materials testing is often carried out at non-ambient temperatures using ovens, furnaces
or cryogenic chambers. Extreme temperature means an operating temperature exceeding
60 °C (140 °F) or below 0 °C (32 °F). You must use protective clothing, such as gloves,
when handling equipment at these temperatures. Display a warning notice concerning
low or high temperature operation whenever temperature control equipment is in use.
You should note that the hazard from extreme temperature can extend beyond the
immediate area of the test.
Hazard - Do not place a testing system off-line from computer control without first
ensuring that no actuator or crosshead movement will occur upon transfer to
manual control.
The actuator or crosshead will immediately respond to manual control settings when the
system is placed off-line from computer control. Before transferring to manual control,
make sure that the control settings are such that unexpected actuator or crosshead
movement cannot occur.
Robotic Motion Hazard - Keep clear of the operating envelope of a robotic device
unless the device is de-activated.
The robot in an automated testing system presents a hazard because its movements are
hard to predict. The robot can go instantly from a waiting state to high speed operation in
several axes of motion. During system operation, keep away from the operating envelope
of the robot. De-activate the robot before entering the envelope for any purpose, such as
reloading the specimen magazine.
Hazard - Set the appropriate limits before performing loop tuning or running
waveforms or tests.
Operational limits are included within your testing system to suspend motion or shut off
the system when upper and/or lower bounds of actuator or crosshead travel, or force or
strain, are reached during testing. Correct setting of operational limits by the operator,
prior to testing, will reduce the risk of damage to test article and system and associated
hazard to the operator.
Electrical Hazard - Disconnect the electrical power supply before removing the
covers to electrical equipment.
Disconnect equipment from the electrical power supply before removing any electrical
safety covers or replacing fuses. Do not reconnect the power source while the covers are
removed. Refit covers as soon as possible.
Warnings

Preliminary Pages
vi M10-16250-EN
Rotating Machinery Hazard - Disconnect power supplies before removing the
covers to rotating machinery.
Disconnect equipment from all power supplies before removing any cover which gives
access to rotating machinery. Do not reconnect any power supply while the covers are
removed unless you are specifically instructed to do so in the manual. If the equipment
needs to be operated to perform maintenance tasks with the covers removed, ensure that
all loose clothing, long hair, etc. is tied back. Refit covers as soon as possible.
Hazard - Shut down the hydraulic power supply and discharge hydraulic pressure
before disconnection of any hydraulic fluid coupling.
Do not disconnect any hydraulic coupling without first shutting down the hydraulic
power supply and discharging stored pressure to zero. Tie down or otherwise secure all
pressurized hoses to prevent movement during system operation and to prevent the hose
from whipping about in the event of a rupture.
Hazard - Shut off the supply of compressed gas and discharge residual gas
pressure before you disconnect any compressed gas coupling.
Do not release gas connections without first disconnecting the gas supply and
discharging any residual pressure to zero.
Explosion Hazard - Wear eye protection and use protective shields or screens
whenever any possibility exists of a hazard from the failure of a specimen,
assembly or structure under test.
Wear eye protection and use protective shields or screens whenever a risk of injury to
operators and observers exists from the failure of a test specimen, assembly or structure,
particularly where explosive disintegration may occur. Due to the wide range of
specimen materials, assemblies or structures that may be tested, any hazard resulting
from the failure of a test specimen, assembly or structure is entirely the responsibility of
the owner and the user of the equipment.
Hazard - Ensure components of the load string are correctly pre-loaded to
minimize the risk of fatigue failure.
Dynamic systems, especially where load reversals through zero are occurring, are at risk
of fatigue cracks developing if components of the load string are not correctly pre-loaded
to one another. Apply the specified torque to all load string fasteners and the correct
setting to wedge washers or spiral washers. Visually inspect highly stressed components
such as grips and threaded adapters prior to every fatigue test for signs of wear or fatigue
damage.
Warnings

vii
Preliminary Pages
Table of Contents
Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
System Description and Terminology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Principle of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Hardware Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
System Components and Interconnections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
System Safety and Information Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Product Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Product Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Chapter 2 Requirements and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Customer’s Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Instron’s Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Frame Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Floor Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Table Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Telephone and Network Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Ceiling Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Environmental Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Accessibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Site Requirements for System Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Environmental Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
C E Approval. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Environmental Impact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Noise Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Preliminary Pages
viii M10-16250-EN
Power Cord Selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Series 5980 Optional Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
5982, 5984 and 5985 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Standard, Extra Height and Extra Wide Options. . . . . . . . . . . . . . . . . . . . . . . 2-10
Second Test Space Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
5988 and 5989 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
Load Frame Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Accessory Mounting Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Checklist for Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
Site Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
Scheduling Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
Chapter 3 Lifting and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
General Handling Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Packaging Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Unpacking Dual Column Frames. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Righting the Frame from a Prone Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Using a Crane. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Using a Forklift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Transporting Dual Column Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Transporting Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Chapter 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Level the Load Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Procedure for 5982, 5984 and 5985 Load Frames. . . . . . . . . . . . . . . . . . . . . . 4-1
Procedure for 5988 and 5989 Load Frames. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Power Supply Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
5982, 5984 and 5985 Load Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
5988 and 5989 Load Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Connect the System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

ix
Preliminary Pages
Connect Optional Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
First Time Startup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Chapter 5 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Daily Maintenance Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Periodic Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
General Maintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Test Limit Stops. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Troubleshooting for Load Cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Ancillary Parts - Frames with a Single Test Space . . . . . . . . . . . . . . . . . . . . . 5-10
Ancillary Parts - Frames with a Second Test Space . . . . . . . . . . . . . . . . . . . . 5-13

Preliminary Pages
x M10-16250-EN

1-1
Chapter 1
Introduction
• System Description and Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
• System Components and Interconnections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
• System Safety and Information Labeling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
• Product Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
• Product Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
These instructions include the following information:
• system specifications that are required for installation of your testing system, for
example required environmental conditions, system weights and dimensions
• transporting your system to its final location, including instructions for lifting and
handling
• installing and connecting all the system components together (carried out by an Instron
Service Engineer for first-time installation)
• configuring the system before you start testing (carried out by an Instron Service
Engineer for first-time installation)
• routine maintenance of the system
• spare parts
Refer to the Operator’s Guide for instructions on running tests.

Chapter: Introduction
1-2 M10-16250-EN
System Description and Terminology
Figure 1-1 on page 1-2 shows the location of components on 5982, 5984 and 5985 load
frames. The 5988 and 5989 frames are substantially the same, except for the location of the
power input and ground stud, as shown in Figure 1-2 on page 1-3.
Front View Rear View
Figure 1-1. 5982, 5984 and 5985 Dual Column Floor Frames
Frame base
Base
Base adapter
Controller
Options panel
Motor cover
Ground stud
Column
cover
T-slots
Ballscrew cover
Crosshead
Top plate
Emergency stop
button
Power switch
Control
panel
beam
System ID label
(5982 only)
Upper
Limit
switch
actuator
Limit
switch
rod
limit
switch
Lower
limit
switch
Load cell
Power input

1-3
Components
The major components of an Instron electromechanical testing system include:
• Load frame with integral controller
• Load cell mounted to the crosshead
• Grips for tension testing or table-mounted anvils on a platen for compression testing.
• Instron approved computer system with Instron Bluehill® software.
Front View Rear View
Figure 1-2. 5988 and 5989 Dual Column Floor Frames
Ground stud
Power input

1-4 M10-16250-EN
Special fixtures are available for applications such as flexure and peel testing. For strain
measurement, an optional strain gauge extensometer attaches to the specimen. You can use
non-contacting extensometers with specimens that are unable to support a contacting
extensometer. Contact your regional Instron office or check our web site at
www.instron.com for assistance with Instron’s grips and fixtures.
The following table defines the components of the testing system:
Principle of Operation
The system communicates primarily through the controller. The controller contains sensor
conditioning cards for the system transducers and transfers data between the transducers and
the computer. The controller also communicates with the load frame via a frame interface
Table 1-1. Testing System Components
Component Description
Load Frame The load frame comprises a base, one or two columns, a moving
crosshead, and a top plate. It is a high stiffness support structure
against which the test forces react.
Each column comprises a guide column and a ballscrew. The
crosshead is mounted on both the guide column and the ballscrew.
Rotation of the ballscrew drives the crosshead up or down while the
guide column provides stability.
Controller The hardware that controls the frame and any ancillary equipment
connected to the testing system. The controller panel contains all the
connectors for load cells, extensometers and any other sensors that
are required for testing.
Control Panel The hardware panel, mounted on the side of the load frame, that lets
you perform some of the software functions directly at the frame.
Load String Comprises all of the components that you install between the moving
crosshead and the load frame base (or fixed crosshead). Typically
this involves a load cell, a set of grips, any adapters that are required
to connect the components, and the specimen to be tested.
Typically, you mount a load cell on the crosshead, then a pair of grips
or fixtures on the load cell and frame base. The grips or fixtures
secure the specimen and when you start a test the crosshead moves
up or down applying a tensile or compressive load to the specimen.
The load cell converts this load into an electrical signal that the
software measures and displays.
Bluehill Software Instron testing software that controls the testing system, running tests
and analyzing test data to produce test results.
Specimen A single piece of material to be tested.

1-5
board (FIB) inside the load frame. The FIB links all the electrical components of the frame
together.
Hardware Controls
The hardware controls consist of:
• Emergency stop button - to be used whenever you need to stop the crosshead
immediately because an unsafe condition exists.
• Limit stops - these must be set before each test session to protect the operator against
unexpected crosshead movement.
• Control panel - lets you perform certain functions at the frame instead of at the
computer. These include starting and stopping a test and using the jog controls to
position the crosshead prior to installing a specimen.
Software
Control of the testing system is carried out via Instron Bluehill software. Setting test
parameters, operating the system, and collecting test data is done through the software
program.
Table 1-2. Software Terminology
Term Description
Test Method In Bluehill software, a test method is a file that contains a set of
defined parameters that the system uses to run tests, analyze the test
data, and produce calculated results.
Sample A group of material specimens, whose properties are studied and
compared to gain statistical or quality assurance information. For
example, you could take a specimen from different parts of a single
manufacturing run of a material to form a sample of the material. The
sample is then representative of the complete run and you can test it
to ensure that the material quality has remained stable over the
complete run. You perform the same test on each specimen in a
sample.

1-6 M10-16250-EN
System Components and Interconnections
Figure 1-3 on page 1-6 and Figure 1-4 on page 1-7 show you how each hardware
component is connected to make up the complete testing system.
Figure 1-3. 5982, 5984 and 5985 System Connections
GRN/YEL - Earth
BRN - Live
BLU - Neutral
Ground stud
Load cell
Load cell connection
Controller
Supplemental ground
cable
Computer interface
connection
Load cell cable
Mains power cable
Ethernet
crossover cable
System
ID label

1-7
System Components and Interconnections
Figure 1-4. 5988 and 5989 System Connections
BLACK - Live 1
BLACK - Live 2
BLACK - Live 3
BLACK - Neutral
GRN/YEL - Earth
Ground stud
Load cell
Controller
Supplemental ground
cable
Computer interface
connection
Load cell cable
Mains power cable
Ethernet
crossover cable
System ID
label

1-8 M10-16250-EN
System Safety and Information Labeling
Table 1-3 on page 1-8 explains the meanings of any safety and information labels that may
be attached to any part of the testing system.
Table 1-3. Safety and Information Labeling Descriptions
Label Meaning Purpose
Electrical
hazard
Indicates that an electrical hazard exists
from high voltage or electrical current.
Disconnect power
supply
Disconnect the power supply before
servicing machine.
Electrical - fuse
warning Indicates an electrical hazard exists.
Advises about disconnecting power mains
before changing fuses and using only
specified fuses.
Belt
entanglement hazard
Indicates that a hazard exists from the
drive belt and pulley system.
High
temperature hazard
Indicates that a heat hazard exists. Stay
clear of area when operating the machine.
Rotating machinery
hazard
Indicates that a rotating hazard exists.
Keep clear of these areas (and tie back
long hair).

1-9
System Safety and Information Labeling
Ground stud Indicates a ground stud.
Read the manual Read and understand the operator’s
manual before using the machine.
Crosshead direction Indicates the direction to turn the pulley to
manually move the crosshead upward.
Pulleys can be turned by hand when
power is disabled.
Crush hazard Indicates the crush hazard of the moving
crosshead and instructs the user to read
and understand the operator’s manual
before using the machine.
Waste Electrical and
ElectronicEquipment
(WEEE)
In accordance with the European Union’s
WEEE directive, the crossed out wheeled
bin symbol indicates that the equipment
must be disposed of separately from other
waste at the end of its usable life. For
advice on the disposal of electrical and
electronic equipment in your country,
contact your local Instron representative.
Table 1-3. Safety and Information Labeling Descriptions (Continued)
Label Meaning Purpose
Crush hazard.
Keep clear of test
area when machine
is in motion.
Read and understand
operator's manual
before using this
machine.
! WARNING

1-10 M10-16250-EN
Product Support
Instron provides documentation, including manuals and online help, that can answer many
of the questions you may have. It is recommended that you review the documentation sent
with the system you purchased for possible solutions to your questions.
If you cannot find answers in these sources, contact Instron’s Service department directly. A
list of Instron offices is available on our website at www.instron.com. In the US and
Canada, you can call directly at 1-800-473-7838.
Product Documentation
Instron offers a comprehensive range of documentation to help you get the most out of your
Instron products. Depending on what you have purchased, your documentation may include
some or all of the following:
We welcome your feedback on any aspect of the product documentation. Please email
info_dev@instron.com with your comments.
Operator’s Guide How to use your system components and controls,
procedures for setting limits, calibration and other
frequently performed operating tasks.
System Support Information about system installation, set up and
configuration, transducer connection and calibration.
Online Help Software products come complete with context
sensitive help, which provides detailed information on
how to use all software features.
Accessory
Equipment Reference
How to set up and use any accessories you have
purchased, for example grips, fixtures, extensometers,
transducers, and environmental chambers.

2-1
Chapter 2
Requirements and Specifications
• Responsibilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
• Site Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
• Environmental Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
• Power Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
• Power Cord Selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
• Series 5980 Optional Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
• 5982, 5984 and 5985 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
• 5988 and 5989 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
• Load Frame Weights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
• Accessory Mounting Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
• Checklist for Site Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
Responsibilities
Customer’s Responsibilities
It is the customer’s responsibility to ensure that all required support services are available,
and that all necessary checks are made prior to installing the testing system. These services
and checks are described below.
Site Preparation
Proper site preparation is imperative so that the testing system operates in accordance with
its specifications and provides accurate test results. The customer must ensure that the site
requirements are satisfied prior to scheduling the installation appointment (refer to “Site
Requirements” on page 2-3).
Handling and Transporting
Unless specifically arranged otherwise, it is the customer’s responsibility to arrange the off-
loading, unpacking and moving of the testing system to the final site location (refer to

Chapter: Requirements and Specifications
2-2 M10-16250-EN
Chapter 3 “Lifting and Handling”).
Upon special arrangements, an Instron service engineer can supervise the off-loading and
transportation of the load frame to its final site. Contact Instron’s Professional Services
department or your local Instron office for additional information on this service (refer to
“Product Support” on page 1-10).
Insurance and Safety
Under Instron’s standard contract, the shipping terms are Ex-Works (or FOB Factory),
meaning ownership and liability for the testing system transfers to the customer at Instron’s
loading dock. Unless other shipping terms are specified in a purchase order, which Instron
does not dispute, the Ex-Works shipping terms apply. Under these terms, the customer is
responsible for securing the applicable transit insurance on the shipment and arranging safe
transport to the final destination. Arrangements can be made through Instron to secure
insurance cover and shipping, at the customer’s expense.
When transporting a load frame within your own premises, you are responsible for its safe
transport. Upon special arrangements, an Instron service engineer can supervise the
transportation to the load frame’s final site. Contact Instron’s Professional Services
department or your local Instron office for additional information on this service (refer to
Materials Disposal
It is the customer’s responsibility to properly dispose of any waste materials generated from
the installation of the system and its accessories, or from the general operation of the system.
This includes packing materials, hydraulic fluid, and waste materials contaminated with
hydraulic fluid. Hydraulic fluid is generally considered a hazardous material so proper
disposal of this substance, or anything contaminated with it, must comply with local, state,
and federal regulations.
Instron’s Responsibilities
Instron’s standard contract requires Instron to provide the necessary services to ensure that
your testing system operates accurately. These services are described below.
Additional services and equipment may be negotiated with Instron, but these additional
services must be mutually agreed upon and specifically described in your purchase order.
Insurance
Under Instron’s standard contract, the shipping terms are Ex-Works (or FOB Factory),
meaning ownership and liability for the testing system transfers to the customer at Instron’s
loading dock. Unless other shipping terms are specified in a purchase order, which Instron

2-3
Site Requirements
does not dispute, the Ex-Works shipping terms apply. Under these terms, Instron is
responsible for insurance cover while the testing system is in the factory up until it reaches
the loading dock for shipping.
Installation
When the site location is prepared and the frame and its components have been moved to the
final operating location (refer to Chapter 3 “Lifting and Handling”), Instron is
responsible for the complete installation of the load frame, its components and any
additional accessories that may have been purchased.
The customer must not make any attempt to install the load frame without an Instron service
representative present.
Initial Operation
Once the installation is complete, Instron performs an initial operation of the load frame and
a calibration check to ensure that it is working properly.
The service representative also performs a required on-site training program. The required
on-site training takes approximately one day to complete, and is designed to accommodate
up to three individuals.
Contact Instron’s Professional Services department for more information on this training
(refer to “Product Support” on page 1-10). Additional training is available through
Instron’s training center.
Documentation
Instron provides all the documentation required to operate the system, including manuals for
the load frame and any required online help systems for software applications.
Additional copies of manuals are available and can be ordered through Instron’s Sales
department.
Site Requirements
Proper site preparation is imperative so that the testing system operates in accordance with
its specifications and provides accurate test results.

2-4 M10-16250-EN
Frame Location
The load frame must not be located against a wall or other object that interferes with air
ventilation around the frame. Proper air ventilation is required to dissipate the heat generated
from the frame base.
Floor Loading
The supporting floor must be checked for its weight loading and be able to support the
weight of the load frame and any other accessory parts that may have been purchased. The
floor must be free of vibrations from other activities taking place in or near the building.
For larger load frames, it is recommended that you consult your facility engineer, foundation
specialist, or a civil engineer to ensure that the load capacity of the floor can support at least
three times the weight of the load frame and its component parts. The higher load capacity is
necessary because large dynamic loads may occur when a specimen breaks and this
additional load may be absorbed into the floor.
Table Loading
The supporting table must be checked for its weight loading and must be able to support the
weight of the load frame with all its components and accessories, if the computer and
accessories are placed on the same table. There must be a sufficient margin of safety in the
table’s weight loading to ensure the stability of the system.
The table must be free of vibrations from other activities taking place in or near the building.
A table with leveling feet is recommended.
Power Supply
Ensure that the required power supply is available and complies with the requirements
detailed under “Power Requirements” on page 2-8.
Caution
Power fluctuations and surges can cause performance problems ranging from
intermittent electrical problems to severe damage.
Instron systems require “clean” and stable electrical power. Unless other arrangements are
made with Instron, you are responsible for providing clean electrical power. An in-line
power surge protector is recommended for all installations.
If you purchased an environmental chamber with your system, it requires a dedicated
electrical power supply that is separate from the power supply for the rest of the system.

2-5
Site Requirements
Telephone and Network Access
Ensure that a telephone line is located within the general testing area. This enables the user
to contact Instron’s service department directly from the testing area so the user can perform
the instructions provided and resolve the situation while on the telephone with the service
representative. This facilitates resolving issues in a timely manner and reduces the number
of repeated phone calls on the same problem.
It is also suggested that network drops, or digital phone lines, be within the general testing
area. A network connection near the system facilitates distributing test data via the network.
Instron’s goal is to provide remote diagnostics in order to resolve system issues. Having a
network drop or digital phone line available will enable an Instron service representative to
dial into the testing system’s computer to diagnose and resolve problems more efficiently.
Including the network or digital lines in your initial site preparation will facilitate adding
this function if it becomes necessary in the future.
Ceiling Clearance
Ensure that there is adequate ceiling clearance so that the load frame can be easily placed in
its testing location. Take into consideration how you will be transporting the frame (by
forklift or crane, for instance) and ensure that the ceiling height can accommodate your
mode of transportation.
Environmental Conditions
Ensure that the testing site meets the standards described under “Environmental
Specifications” on page 2-6.
Accessibility
The testing system must be accessible for routine maintenance without having to move the
load frame. If the frame is moved, it may need to be re-verified.
Site Requirements for System Accessories
Some of Instron’s accessories require additional site requirements. If you are not sure if the
accessories you purchased require any of the following site preparations, contact Instron’s
Professional Services department or your local Instron office for advice.
Dry Compressed Air
Dry, compressed air is required for pneumatic grips. Typically, 90 psi air is required with a
water trap/filter.

2-6 M10-16250-EN
Water Supply
A water supply may be required for some specimen grips and some temperature control
systems.
Liquid Nitrogen and Carbon Dioxide
A Liquid Nitrogen (LN2) or Carbon Dioxide (CO2) supply may be required for
environmental chambers with cooling options.
For carbon dioxide, tank pressure must be approximately 725 psi. It must be in a liquid state
when it reaches the valve of the environmental chamber.
For liquid nitrogen, tank pressure must be between 5 and 10 psi, depending upon the
regulator and relief valves that are fitted to the dewar flask. Do not exceed 20 psi.
Environmental Specifications
General
C E Approval
All floor model load frames meet the requirements of EN61236-1 (2006) Equipment for
Measurement Control and Laboratory Use (Industrial Locations) using CISPR 11 (2004) per
Class code A.
Table 2-1. Environmental Specifications
Parameter Specifications
Operating
Temperature
+5°C to +40°C (+41°F to +104°F)
Storage
Temperature
-25°C to +55°C (-13°F to +131°F)
Humidity 10% to 90% (non-condensing)
Environmental
Conditions
Designed for use under normal laboratory conditions. Protective measures may
be required if excessive dust, corrosive fumes, electromagnetic fields or
hazardous conditions are encountered.

2-7
Environmental Specifications
Environmental Impact
Instron materials testing systems and their accessories are designed to produce no adverse
environmental impact during normal use as long as they are operated and serviced in
accordance with their operating instructions.
Normal care must be taken with service items such as greases and oils needed to operate and
maintain the equipment as indicated in their packaging and operating instructions.
These systems comprise mechanical and electronic components that contain potentially
environmentally harmful chemicals, such as chromium, chromates, lead and brominated fire
retardants. Care must be taken at the end of the equipment's life to ensure its disposal in
accordance with local environmental regulations.
Because of the wide range of applications where our instruments are used, Instron has no
knowledge of the environmental impact of the customer's test pieces or specimens.
Noise Levels
Noise levels do not include noise from specimen breaks.
Table 2-2. Series 5980 Noise Levels
Maximum Noise Level dB(A)
Test Speed 5982 5984 5985 5987 5989
Standby or low speed 55 55 55 58 58
Maximum rated speed 72 74 72 72 72

2-8 M10-16250-EN
Power Requirements
For models 5988 and 5989 the mains voltage must be in a “WYE” configuration with
neutral and ground. A Delta configuration requires an external Delta-to-Wye
transformer rated to a minimum of 5kVa. A rating of 7.5kVa is recommended.
Table 2-3. Series 5980 System Power Requirements
Parameter
Specifications
5982 a
5984 a
5985 a
5988 5989
Maximum Power
(VA)
3500 4800
Voltage (Vac)
(±10%)
200/208, 220, 230, 240
Single Phase
208/120, 240/139, 400/230, 480/277
3 Phase
Recommended
Circuit Breakerb
20 Amp Type C 3-pole Type C circuit breaker, each rated at:
20 Amp Type C for voltage 208/120
or
16 Amp Type C for all other voltages
Frequency 47 to 63 Hz
a. Although these frames can operate at the indicated voltages, high speed turn-around times will be affected if voltage is
near extreme of tolerance.
b. A Type C circuit breaker is required between the facility power source and the load frame to accommodate high in-rush
currents at switch on.
Figure 2-1. 5-wire WYE 3-Phase Diagram
Phase A
Winding A
Winding B
Phase B
Winding C
Phase C
Neutral
Ground

2-9
Power Cord Selections
Warning
Power Cord Selections
When you place your order for a 5982, 5984 or 5985 load frame, you can choose the voltage
required and your choice of voltage determines the type of power cord supplied, as follows:
• 200/208V is supplied with a NEMA L6-20P plug
• 220, 230 and 240V is supplied with an IEC 309-16A plug
These power cords are 3 metres (9.8 ft) in length.If you do not make a choice, Instron
chooses the customary voltage that matches the shipping destination for the system.
When you place your order for a 5988 or 5989 load frame, you can choose the voltage that
you require. If you do not make a choice, Instron chooses the customary voltage that
matches the shipping destination for the system. These frames are always supplied with
flying leads, 5.8 metres (19 ft) long.
You must use GFCI (Ground Fault Circuit Interruption) protection on all power
sources if your testing system includes water or any other fluid.
If your system includes any fluids (e.g. water-cooled grips, BioPuls baths, food testing
fixtures), you must use GFCI protection on all power sources to protect the operator from
fluids that might leak into the load frame electronics.

2-10 M10-16250-EN
Series 5980 Optional Configurations
In addition to the standard height, standard width model with a single test space below the
moving crosshead, 5982, 5984 and 5985 load frames are available in several frame options
for specialized testing, as follows:
• Extra wide - for large assemblies
• Extra height - for unusually long specimens
• Second test space - lets you test above the moving crosshead
5988 and 5989 load frames are available in standard configurations only.
Table 2-4 on page 2-10 summarizes the options and combination of options that are
available.
5982, 5984 and 5985 Dimensions
Standard, Extra Height and Extra Wide Options
Figure 2-2 on page 2-11 shows the frame dimensions. Refer to Table 2-5 on page 2-12
and Table 2-6 on page 2-12 to match the letter designations.
Table 2-4. 5980 Optional Frame Combinations
Optional
Configuration
Load Frame Model
5982 5984 5985
5988 and
5989
Extra Wide Yes Yes Yes No
Extra Height Yes Yes Yes No
Extra Wide + Extra
Height
Yes Yes Yes No
Second Test Space Yes Yes Yes No
Extra Height with
Second Test Space
Yes Yes Yes No

2-11
Figure 2-2. 5982, 5984 and 5985 Load Frame Dimensions
F
50 ±16
B
A
498
G
93
J
55
300
777
389
200

D
E
Optional Base Extension

2-12 M10-16250-EN
Table 2-5. 5982 with Single Test Space
Dimension - mm (in) Letter
Frame
Option
Standard
Height and
Width Extra Height Extra Wide
Extra Height
and Extra
Wide
Top plate length A 1105 (43.5) 1105 (43.5) 1464 (57.6) 1464 (57.6)
Horizontal test space B 575 (22.6) 575 (22.6) 934 (36.8) 934 (36.8)
Crosshead thickness D 148 (5.8) 148 (5.8) 200 (7.9) 200 (7.9)
Minimum crosshead
position
E1 100 (3.9) 100 (3.9) 100 (3.9) 100 (3.9)
Maximum crosshead
position
E2 1430 (56.3) 1930 (76) 1430 (56.3) 1930 (76)
Overall height F 2273 (89.5) 2773 (109.2) 2273 (89.5) 2773 (109.2)
Overall height with
optional base extension
2573 (101.3) 3073 (121)
Overall width G 1130 (44.5) 1130 (44.5) 1489 (58.6) 1489 (58.6)
Load cell height J 110 (4.3) 110 (4.3) 110 (4.3) 110 (4.3)
Table 2-6. 5984 and 5985 with Single Test Space
Frame
Option
Standard
Height and
Extra Height
and Extra
Wide
Top plate length A 1105 (43.5) 1105 (43.5) 1464 (57.6) 1464 (57.6)
Horizontal test space B 575 (22.6) 575 (22.6) 934 (36.8) 934 (36.8)
Crosshead thickness D 200 (7.9) 200 (7.9) 225 (8.9) 225 (8.9)
Minimum crosshead
position
E1 100 (3.9) 100 (3.9) 75 (2.9) 75 (2.9)
Maximum crosshead
position
E2 1430 (56.3) 1930 (76) 1405 (55.3) 1905 (75)
Overall height F 2273 (89.5) 2773 (109.2) 2273 (89.5) 2773 (109.2)

2-13
Second Test Space Options
The second test space option lets you test in the space above the moving crosshead, as
shown in Figure 2-3 on page 2-13.
In this configuration, the top place is replaced with a fixed crosshead. Hoes are drilled in the
fixed crosshead to mount the load cell or grip adapter. The specimen is gripped between the
fixed crosshead and the top of the moving crosshead.
Figure 2-4 on page 2-14 shows the dimensions for the second test space. Refer to Table 2-
7 on page 2-14 and Table 2-8 on page 2-14 to match the letter designations.
Overall height with
2573 (101.3) 3073 (121)
Overall width G 1130 (44.5) 1130 (44.5) 1489 (58.6) 1489 (58.6)
Load cell height J 170 (6.7) 170 (6.7) 170 (6.7) 170 (6.7)
Table 2-6. 5984 and 5985 with Single Test Space
Frame
Option
Standard
Height and
Extra Height
and Extra
Wide
Figure 2-3. Second Test Space Configuration

2-14 M10-16250-EN
Figure 2-4. Second Test Space Dimensions
148
1037
C
F
Table 2-7. 5982 with Second Test Space
Frame Option
Standard
Height and
Width Extra Height
Top plate thickness C 148 (5.8) 148 (5.8)
Overall height F 2354 (92.7) 2905 (114.4)
Table 2-8. 5984 and 5985 with Second Test Space
Frame Option
Standard
Height and
Width Extra Height
Top plate thickness C 200 (7.9) 200 (7.9)
Overall height F 2406 (94.7) 2957 (116.4)

2-15
5988 and 5989 Dimensions
5988 and 5989 Dimensions
Figure 2-5 on page 2-15 shows the frame dimensions. Refer to Table 2-9 on page 2-16 to
match the letter designations.
Figure 2-5. 5988 and 5989 Load Frame Dimensions
1495
1545
259
3128
964
285
611
53
68
41
1594
763
420
A
B1 B2

2-16 M10-16250-EN
Load Frame Weights
Table 2-9. 5988 and 5989 Dimensions
Frame
5988 5989
Crosshead thickness A 200 (7.9) 250 (9.8)
Minimum crosshead
position
B1 200 (7.9) 150 (5.9)
Maximum crosshead
position
B2 2050 (80.7) 2000 (78.7)
Table 2-10. Weights - Standard Configuration
Model Number
Weight
of Load Frame
Weight of Load Frame with
5982 784 kg (1725 lb) 875 kg (1925 lb)
5984 882kg (1940 lb) 973 kg (2140 lb)
5985 882 kg (1940 lb) 973 kg (2140 lb)
5988 2255 kg (4960lb) n/a
5989 2516 kg (5535lb) n/a
Table 2-11. Weights - Optional Configurations
Model Number Optional Configuration
Weight
of Load Frame
5982 Extra height 898 kg (1975 lb)
Extra wide 1011 kg (2225 lb)
Second test space 970 kg (2135 lb)
Extra height with second test space 1084 kg (2385 lb)
Extra height and extra wide 1102 kg (2425 lb)

2-17
Accessory Mounting Dimensions
You can attach numerous testing accessories and fixtures to the load frame for specialized
tests. Use the standard mounting holes shown in the following diagrams to mount your
accessories. Avoid tapping new holes that may weaken or otherwise compromise the
integrity of the load frame.
5984
5985
Extra height 955 kg (2100 lb)
Extra wide 1100 kg (2420 lb)
Second test space 1068 kg (2350 lb)
Extra height with second test space 1141 kg (2510 lb)
Extra height and extra wide 1182 kg (2600 lb)
Table 2-11. Weights - Optional Configurations (Continued)
Model Number Optional Configuration
Weight
of Load Frame
All measurements in the following figures are shown in mm.

2-18 M10-16250-EN
Base Beam
Figure 2-6. 5982 Base Beam Mounting Dimensions
150 150 150
75
150
75
90
45
280
140
M30 x 2-6H
40 Deep, LH
Ø40 x 3 Deep
M16 x 30 Deep
(8X or 12X for extra wide)
M10 x 25 Deep
(10X)
Front of frame
Ø100
150
150
Figure 2-7. 5984 and 5985 Base Beam Mounting Dimensions
150 150 150
75
150
75
90
45
280
140
Ø60 x 3 Deep
M16 x 30 Deep
(8X or 12X for extra wide)
M10 x 25 Deep
(10X)
Front of frame
Ø100
M48 x 2-6H
52 Deep, LH
150 150

2-19
Figure 2-8. 5988 and 5989 Base Beam Mounting Dimensions
B B B B
B
B
B B
A
A
A
A
A
A
A
A
A
A
A
A A
B B
A
A
A
A
A
A
A
600
150 150
300
450
266.7
280
85
225
200
100
90
45
B B B B
B
B
B B
A
A
A
A
A
A A
5989 Base Beam
M48 x 2-6H
60 Deep, LH
5988 Base Beam
Ø60 x 3 Deep Ø60 x 3 Deep
Ø60 x 3 Deep
M72 x 3-6H
90 Deep, LH
Ø82.6 x 5 Deep
M10 x 1.5-6H
“A”
M20 x 2.5-6H
“B”
25 Deep
50 Deep

2-20 M10-16250-EN
Crosshead
Figure 2-9. 5982 Moving Crosshead Mounting Dimensions
482
280
140
45
90
M10 x 25 Deep
(10X)
Ø100
Ø11 Thru
(6X)
Front of frame
Topside of moving crosshead
Ø40 x 3 Deep
M16 x 35 Deep
(2X)
90
45
140
280
M10 x 25 Deep
(10X)
Front of frame
Underside of moving crosshead
Ø100
Ø40 x 3 Deep
Ø32 Thru

2-21
Figure 2-10. 5984 and 5985 Moving Crosshead Mounting Dimensions
280
130
65
140
241
482
45
90
38
75
M10 x 25 Deep
(10X)
Ø22 Thru
Ø31.75 x 28
M16 x 35 Deep
(8X)
Ø100
Front of frame
(4X)
Deep Counterbore
Ø60 x 3 Deep
Topside of moving crosshead
280
140
90
45
Underside of moving crosshead
Ø60 x 3 Deep
M10 x 25 Deep
(10X)
Ø100
Ø51 Thru

2-22 M10-16250-EN
Figure 2-11. 5982 Second Test Space Configuration - Fixed Crosshead Mounting
Dimensions
482
241
Topside of Crosshead
Ø32 Thru
Ø100
Front of frame
Ø11 Thru
(6X)
M16 x 35 Deep
(8X)
280
90
140
45
Underside of Crosshead
M10 x 25 Deep
(10X)
Ø100
Ø60 x 3 Deep

2-23
Figure 2-12. 5984 and 5985 Second Test Space Configuration - Fixed Crosshead Mounting
Dimensions
482
65
130
241
75
38
Front of frame
Ø22 Thru
Ø31.75 x 28
(4X)
M16 x 35
(2X)
Ø51 Thru
Deep
280
140
90
45
75
38
Ø60 x 3 Deep
M10 x 25 Deep
(10X)

2-24 M10-16250-EN
Figure 2-13. 5988 and 5989 Crosshead Mounting Dimensions
90 45
280
266.7
700
140
60°
350
M10 x 25 Deep
(10X)
Ø100
Ø60 x 3 Deep
M20 x 50 Deep
(2X)
A
B
5988 “A” =Ø51 Thru and “B” = Ø60 x 3 Deep
5989 “A” = 74.75 thru and “B” = Ø82.6 x 5 Deep
280
700
90 45 140
350
M10 x 25 Deep
(4X)
M20 x 50 Deep
(2X)

2-25
Top Plate
The top plate is not a load bearing component of the machine.
Figure 2-14. 5980 Series Top Plate Mounting Dimensions
280
90
M10 Threaded
inserts (4X)

2-26 M10-16250-EN
Checklist for Site Preparation
The following checklist provides a quick summary of items that should be considered when
planning and preparing the site location of your testing system. Additional information
regarding each item below is provided within this manual. If you need more specific
information, contact Instron’s Professional Services department or your local Instron office
for assistance (refer to “Product Support” on page 1-10).
Site Location
 Floor and table is able to support the weight of the frame, and its computer components.
 Environment complies with the specifications for your specific model:
• Operating temperature
• Storage temperature
• Humidity
• Atmosphere
 The required power supply is available and is compatible with the electrical
requirements for your specific model.
 Electrical outlets are within the maximum distance requirement to the load frame’s
location.
 Phone lines are located within the general testing area so that users can call Instron’s
service department directly from the testing area. It is also suggested that network drops,
or digital phone lines, be within the general testing area.
 Ceiling clearance is adequate for the load frame, including the additional space
necessary to lift and move the frame by either a forklift or crane.
 Location provides sufficient accessibility for routine maintenance (915 mm or 36 in).
 Employees are adequately trained to operate the load frame and its computer system.
Transporting
 You have the correct number of packing boxes as stated on the packing list.
 Insurance coverage is secured or verified.
Not all computers are compatible with Instron testing systems. If you intend to purchase a
computer from an outside vendor, contact Instron Service to verify its compatibility.
Additional charges may result from service that is required to evaluate or reconfigure non-
approved computers.

2-27
Checklist for Site Preparation
 You have the required equipment for the chosen transporting method.
 You have the appropriate packaging to protect the load frame when moving or relocating
it.
 Pathway from the loading dock to the final site location has sufficient width and height
to fit the frame and forklift (or crane). Measure all doors and hallways. If you transfer
the load frame while it is still in its packaging, refer to “Packaging Dimensions” on
page 3-2. If you move or relocate the load frame without its packaging, refer to the
dimensions for your specific model number, “Series 5960 Dimensions” on page 2-
11.
 Floor area along the pathway to the final site location is able to support the weight of the
frame and forklift (or crane). Refer to “Packaging Dimensions” on page 3-2 for the
total package weight of your frame or to the weight specification for your specific model
number, “Load Frame Weights” on page 2-16.
 There are no loose accessories on the shipping skid or frame.
 Your equipment operators have the appropriate licenses and have complied with your
local safety standards (i.e. the appropriate training required by OSHA in the U.S.).
Scheduling Installation
When the testing site is ready, and the frame has been moved to its final operating location,
contact Instron Professional Services to schedule an installation appointment:
Worldwide Contact your local Instron Sales and Service office.
A list of Instron offices is available on our website at
www.instron.com.
In the United States
Canada:
1-800-473-7838

2-28 M10-16250-EN

3-1
Chapter 3
Lifting and Handling
• General Handling Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
• Packaging Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
• Unpacking Dual Column Frames. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
• Righting the Frame from a Prone Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
• Transporting Dual Column Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
General Handling Precautions
Only individuals experienced with the operation of lifting equipment and rigging techniques
should attempt to lift or move an Instron system. Equipment operators must have the
appropriate licenses and have complied with your local safety standards (e.g. the appropriate
training required by OSHA in the U.S.).
Always follow the instructions provided with the shipping package. Contact Instron if you
require any additional information or if any part of the shipment is damaged (refer to

Chapter: Lifting and Handling
3-2 M10-16250-EN
Warnings
Packaging Dimensions
Instron recommends leaving the load frame in its packaging while moving it to its final site
location within your building.
Use the information in this section to verify that:
• the packaged frame fits through all doorways and hallways leading to the final location
• all floors leading to the final location can support the weight of the packaged frame
Hazard - do not lift the frame by the top plate. This plate does not support the
weight of the frame. The plate could break and cause personal injury and
equipment damage. Refer to the “System Description and Terminology” on
page 1-2 to identify the top plate.
Hazard - Do not use a lifting device or straps rated for less than twice the weight
of the load frame. All lifting devices and straps must be rated for a capacity at
least twice the weight of the load frame.
Hazard - Do not tilt an unsupported load frame more than 10° when it is in the
upright position. Doing so may topple the load frame and cause personal injury
and damage.
Table 3-1. Packaging Dimensions for 5980 Standard Frame Models
Model # Length Width Height
Packaged
Weight
5982 2623 mm
103 in
1524 mm
60 in
1524 mm
60 in
1047 kg
2303 lb
5982 with optional
base extension
2923 mm
115 in
1524 mm
60 in
1524 mm
60 in
1180 kg
2600 lb
5984 and
5985
2623 mm
103 in
1524 mm
60 in
1524 mm
60 in
1173 kg
2581 lb
5984 and 5985
with optional base
extension
2923 mm
115 in
1524 mm
60 in
1524 mm
60 in
1293 kg
2850 lb

3-3
Unpacking Dual Column Frames
Unpacking Dual Column Frames
Before moving the load frame, review the following sections:
• “Site Requirements” on page 2-3.
5988 3353 mm
136 in
2058 mm
81 in
1397 mm
55 in
2890 kg
6358 lb
5989 3353 mm
136 in
2058 mm
81 in
1397 mm
55 in
3151 kg
6932 lb
Table 3-1. Packaging Dimensions for 5980 Standard Frame Models (Continued)
Model # Length Width Height
Packaged
Weight
Table 3-2. Packaging Dimensions for 5900 Optional Frame Configurations
Frame Configuration Model # Length Width Height
Packaged
Weight
Floor models with
second test space
5982
5984/
5985
2517 mm
99 in
2568 mm
101 in
1524 mm
60 in
1524 mm
60 in
915 mm
36 in
915 mm
36 in
1286 kg
2829 lb
1410 kg
3102 lb
Floor models with
extra height
5982
5984/
5985
2923 mm
115 in
2923 mm
115 in
1524 mm
60 in
1524 mm
60 in
915 mm
36 in
915 mm
36 in
1177 kg
2589 lb
1263 kg
2779 lb
Floor models with
extra height and
second test space
5982
5984/
5985
3025 mm
119 in
3076 mm
121 in
1524 mm
60 in
1524 mm
60 in
915 mm
36 in
915 mm
36 in
1420 kg
3124 lb
1505 kg
3311 lb
Floor models with
extra width
5982
5984/
5985
2441 mm
96 in
2441 mm
96 in
1829 mm
72 in
1829 mm
72 in
915 mm
36 in
915 mm
36 in
1337 kg
2941 lb
1454 kg
3199 lb
Floor models with
extra width and
extra height
5982
5984/
5985
2923 mm
115 in
2923 mm
115 in
1829 mm
72 in
1829 mm
72 in
915 mm
36 in
915 mm
36 in
1448 kg
3192 lb
1557 kg
3433 lb

3-4 M10-16250-EN
• “Transporting Procedures” on page 3-9.
Unpack the load frame in the following sequence:
1. Move the load frame, still in the shipping material, to its final location within your
building. Use a forklift (or crane) to transport the frame from the shipping dock to the
final location. Unpack the load frame after it has been moved to its final location.
2. Remove the shipping material, leaving the load frame fastened to the shipping skid.
3. Remove the shrink wrap vapor barrier encasing the load frame.
4. Use the packing list to inventory all the boxed items. Some accessories may be in the
container with the load frame or may be packaged separately.
• Do not open any of the packing boxes until the Instron service engineer arrives to
install your testing system. The packing list indicates the total number of boxes that
are included in the shipment. Count the number of boxes you received to make sure
you have the correct number of boxes. This ensures that no parts are lost prior to
installation.
• Do not disassemble or remove any components or parts from any Instron frame or
accessory.
5. Retain all packing materials until the system is satisfactorily installed and all parts,
assemblies and accessories are located.
6. If the load frame is in a horizontal position, refer to “Righting the Frame from a Prone
Position” for instructions.
7. Move the load frame into its operating location using the selected transportation method.
Refer to “Transporting Procedures” on page 3-9 for additional information.
Righting the Frame from a Prone Position
Your frame may have been shipped in a horizontal position, so it must be moved into an
upright, standing position before placing it in its operating location.
After unpacking the load frame, it may be necessary to position the frame into its operating
location. Do not remove the wooden skid until you decide which method will be used to
move the frame to its operating location. The skid is required if you choose to lift the frame
from under the base. Refer to “Transporting Procedures” on page 3-9 for the possible
transporting methods.

3-5
Using a Crane
If you elect to use a crane to move the load frame, Instron recommends using professional
riggers experienced in moving heavy equipment.
Before You Begin
Before moving the load frame ensure that:
• The load frame is not bolted to the shipping skid.
• There are no loose accessories on the shipping skid.
• There is adequate ceiling clearance to allow the load frame to be lifted into a vertical
position, including clearance for the crane.
• Your equipment operators have the appropriate licenses and have complied with your
local safety standards (e.g. the appropriate training required by OSHA in the U.S.).
Equipment
The following items are required:
• A crane with a load rating that is double the load frame’s gross weight.
• Two lifting slings, each with a load rating that is double the load frame’s gross weight.
Procedure
To lift the load frame into a vertical position:
1. Remove all packaging material from the frame and ensure that the frame is not attached
to the shipping skid. This includes the L brackets securing the base to the shipping skid,
and the 4x4 brace and rods protecting the crosshead.
2. Attach the two lifting slings to the crosshead and secure them to the crane hook as
shown in Figure 3-1 on page 3-6. If you use chains in lieu of lifting slings, wrap
protective material around the crosshead to protect the crosshead from scratching and
marring.

3-6 M10-16250-EN
Warning
3. Slowly lift the frame until it is in an upright position and is lifted off the floor.
4. Slowly move the load frame away from the shipping skid and remaining packaging
materials.
5. When the frame is clear of the packaging material, slowly lower the load frame to the
floor so that it is standing on its base in an upright position.
6. Remove the slings from the crosshead.
The frame can now be positioned into its operating location and then installed by an Instron
service representative. To position the frame into its operating location, use the crosshead
method to lift the frame. Refer to “Crosshead Method” for details.
Using a Forklift
Before You Begin
• The load frame is not bolted to the shipping skid.
Crush hazard - Ensure that all persons in the immediate area are standing away
from the frame during lifting.
Do not lift the frame more than 8 cm (3 in) off the floor.
Figure 3-1. Righting a Load Frame Using a Crane

3-7
• There is adequate ceiling clearance to allow the load frame to be lifted into a vertical
position, including clearance for the forklift’s arms, which will be above the load frame.
Equipment
The following items are required:
• A forklift with a load rating that is double the load frame’s gross weight.
• Forklift extenders to extend the forklift arms.
• Two lifting slings, each with a load rating that is double the load frame’s gross weight.
• Ratchet lever hoist (come-along) to stabilize the base of the frame while moving the
frame into an upright position.
Procedure
Prior to moving the frame, it is recommended that you contact Instron service for additional
guidance when righting the frame.
To lift the load frame into a vertical position:
1. Remove all packaging material from the frame and ensure that the frame is not attached
to the shipping skid. This includes the L brackets securing the base to the shipping skid,
and the 4x4 brace and rods protecting the crosshead.
2. Attach the forklift extenders to the forklift arms.
3. Raise the forklift’s arms high enough so that they can pass over the base of the load
frame. Angle the arms back toward the mast so that the lifting slings cannot slip off the
ends.
4. Using the forklift, approach the frame from the base end of the load frame. Position the
forklift so that the arms are directly over the load frame’s base. Leave at least 36 inches
of space between the forklift and the base of the frame.
5. Tie each lifting sling around the crosshead and then around each forklift arm extender.
Ensure that both are taut and secure.
6. Attach one end of the ratchet lever hoist (come-along) to the base of the frame and the
other end to a fixed point. The ratchet lever hoist provides stability to the frame while it
is moving into the upright position.

3-8 M10-16250-EN
Warning
7. Slowly and carefully raise the forklift arms upward to lift the crosshead and the top of
the frame. The forklift arms should be high enough to allow enough clearance for the
load frame to rotate into an upright position. Continue lifting the forklift arms until the
load frame is in an upright position and is lifted off the floor.
8. Slowly reverse the forklift to back away from the shipping skid and remaining
packaging materials.
9. Once the frame is clear of the packaging material, slowly lower the load frame to the
floor so that it is standing on its base in an upright position.
10. Remove the slings from the crosshead.
The frame can now be positioned into its operating location and then installed by an Instron
service representative. To position the frame into its operating location, use the crosshead
method to lift the frame. Refer to “Crosshead Method” for details.
Transporting Dual Column Frames
Before You Begin
• You have reviewed “Site Requirements” on page 2-3. Verify that all conditions are
met prior to transporting the test system.
• At the final site location, there is adequate clearance between the ceiling and the top of
the load frame, including clearance for lifting the frame via a forklift or crane.
• The frame and forklift (or crane) can fit through all doorways, halls, elevators or stairs
from the shipping dock to its final site location. When transferring the load frame while
it is still in its packaging, refer to the dimensions for your frame type in “Packaging
Dimensions” on page 3-2. If you move or relocate the load frame without its
packaging, refer to the dimensions for your specific model ( Chapter 2

3-9
“Requirements and Specifications”).
• The floors from the shipping dock to the final site location have sufficient support for
the weight of the load frame and forklift (or crane) combined.
• You have adequate packaging materials to protect the load frame when moving or
relocating it to another site. Contact Instron’s Service Department to determine the
appropriate packaging requirements for your model type.
Equipment
• A forklift or crane with a load rating that is double the load frame’s gross weight.
• Protective padding for the crosshead.
• 8 mm wrench for securing bolts for the table top machines.
Caution
If the shipping skid has been removed, do not lift the frame with a forklift underneath
the base. Lifting the frame in this manner will damage the underside of the frame.
Similarly, do not lift the load frame by the top plate. This plate is not designed to
support the weight of the frame, and it might break.
If the shipping skid has been removed, then lift the frame using a forklift with padded forks
inserted under the crosshead. Refer to “Crosshead Method” on page 3-11 for details.
Transporting Procedures
There are three methods for transporting the load frame to the test site:
• Frame Base method - Using a forklift to lift the upright load frame from underneath the
base with the shipping skid still attached. Refer to Figure 3-2 on page 3-10.
• Crosshead method - Using a forklift with padded forks to lift the load frame from under
the crosshead as shown in Figure 3-3 on page 3-11.
• Crane method - Using a crane to lift the upright load frame from the crosshead. If this
method is used, Instron recommends using professional riggers experienced in moving
heavy equipment.
Frame Base Method
This method requires that the base be firmly attached to a shipping skid. The center of the
base, where the forklift arms would be placed if no shipping skid was used, cannot support
the weight of the load frame.

3-10 M10-16250-EN
To transport the load frame using the frame base method:
1. Ensure that the frame is bolted to the shipping skid.
2. Carefully insert the forks under the shipping skid as shown in Figure 3-2 on page 3-10.
3. The crosshead should be in its lowest position so that the frame is not top heavy.
Warning
4. Slowly and carefully lift the frame off the floor.
5. Move the frame to its operating location.
6. Slowly lower the frame to the floor.
7. Before placing the frame in its operating location, you must insert the leveling feet into
each corner of the base. The shipping skid must be removed to insert the feet and before
placing the frame in its operating location. Follow the instructions described under
“Crosshead Method” on page 3-11 to remove the shipping skid, insert the leveling
feet and position the frame.
When the frame is in its operating location, you can proceed with the installation process.
Figure 3-2. Lifting the Frame from the Base
Crosshead
Shipping skid
Shipping bolt
(Total of 4)
Forklift arm
Load frame base

3-11
Crosshead Method
This method requires protective padding on either the crosshead or forklift arms to protect
the crosshead from scratching or marring.
This method can be used to:
• Transport the load frame to the site location.
• Lift a tabletop load frame onto a table or workbench.
• Lift the frame to remove the transport skid from the frame’s base and to insert the
leveling feet.
To transport the load frame using the crosshead method:
1. Ensure that there are no shipping bolts attached to the skid.
2. Using a forklift with padded forks or protective material around the crosshead, carefully
insert the forks under the crosshead between the columns. Refer to Figure 3-3 on
page 3-11.
Warning
Figure 3-3. Lifting the Frame from the Crosshead
Leveling feet
Crosshead
Forklift arm

3-12 M10-16250-EN
4. Remove the shipping skid, if it has not already been removed.
5. Move the frame to its operating location.
6. Four leveling feet are supplied for the load frame. Thread one leveling foot into each
corner of the base before placing the frame in its testing location.
7. Place the load frame carefully into position.
8. Remove the padded forks from under the frame’s crosshead.
When the frame is in the testing location, you can proceed with the installation process.
Crane Method
Instron recommends using professional riggers experienced in moving heavy equipment.
To transport the load frame using the crane method:
1. Attach the two lifting slings to the crosshead and secure them to the crane hook as
shown in Figure 3-4 on page 3-13. If you use chains in lieu of lifting slings, wrap
protective material around the crosshead to protect the crosshead from scratching and
marring.
Warning
3. Remove the shipping skid, if it has not already been removed.
4. Move the frame to the operating location.
5. Four leveling feet are supplied for the load frame. Thread one leveling foot into each
corner of the base before placing the frame into its testing location.
6. Place the load frame carefully into position.
7. Remove the lifting straps from the crosshead, and any protective padding, if used.
When the frame is in its testing location, you can proceed with the installation process.

3-13
Figure 3-4. Lifting Load Frame with a Crane
Lifting sling Crane hook
Crosshead
Load frame

3-14 M10-16250-EN

4-1
Chapter 4
Installation
• Level the Load Frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
• Power Supply Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
• Connect the System Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
• Connect Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
• First Time Startup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Level the Load Frame
Level the load frame immediately after you position it for installation. This prevents the base
from rocking and provides a level test surface for more accurate test results. Refer to
Figure 4-1 on page 4-2 and Figure 4-2 on page 4-2.
Equipment
• Spirit level.
• Open-end wrench
• 18 mm socket wrench (5988 and 5989 frames only).
Procedure for 5982, 5984 and 5985 Load Frames
1. Place a spirit level on the center of the base beam.
2. Loosen the lock nut (1) on each leveling foot.
3. Using the wrench, turn the level adjuster nut (2) on each foot while you monitor the
spirit level reading.

Chapter: Installation
4-2 M10-16250-EN
Warning
.
4. Rotate the spirit level 90° to verify that the load frame is level side to side and front to
back.
5. When the machine is level, tighten the lock nut on each leveling foot.
Procedure for 5988 and 5989 Load Frames
The procedure for 5988 and 5989 load frames is the same in principle as for the other floor
model frames. However, as shown in Figure 4-2 on page 4-2, the lock nut and hex nut for
adjustment is above the frame base. You must therefore remove the front and rear covers
from the machine to expose these nuts.
As you make adjustments, make sure no more than 12mm (0.5in) of thread is
exposed. If you expose more thread, there is a risk that the threaded adapter can
separate from the foot.
Figure 4-1. Adjusting a Leveling Foot
Figure 4-2. Leveling Foot on 5988 and 5989 frames
Frame base
Loosen the lock nut
Turn hex nut to adjust level

4-3
Power Supply Compatibility
1. Remove the screws from both front and rear covers and remove the covers from the load
frame.
2. Place a spirit level on the center of the base beam.
3. Loosen the lock nut on each leveling foot.
4. Using an 18mm socket wrench, alternately adjust the height of each leveling foot while
you monitor the spirit level reading.
5. Rotate the spirit level 90° to verify that the load frame is level side to side and front to
back.
6. When the machine is level, tighten the lock nut on each leveling foot.
7. Replace the front and rear covers.
Power Supply Compatibility
The load frame voltage is factory set, according to the voltage that was specified at the time
of purchase. Look at the label next to where the power cable connects to the machine to see
the current voltage setting.
Warning
The voltage settings are inside the machine and can only be changed by a qualified Instron
Service Engineer. Contact Instron Professional Services for assistance if you need to change
the voltage setting.
5982, 5984 and 5985 Load Frames
Verify the following before proceeding with installation:
• The machine’s voltage is compatible with the main power supply to your facility.
• The machine’s power cable can reach the electrical power supply with some slack in the
cable. The power cable is 3 metres (9.8 ft) long.
• The plug is compatible with the electrical power outlet.
Hazard - Do not remove covers to any component of your system, unless it is
specified in a procedure.
There are dangerous voltages and rotating machinery inside the machine that may cause
bodily injury or damage to equipment.

4-4 M10-16250-EN
• To accommodate high in-rush currents, connect a time delay circuit breaker between the
facility power source and the load frame (refer to Table 2-3 on page 2-8).
The power cord set and plug is based on the voltage selection for the country to which the
frame is shipped and is compatible with the electrical requirements for that country.
5988 and 5989 Load Frames
Verify the following before proceeding with installation:
• The machine’s voltage is compatible with the main power supply to your facility.
• The machine’s power cable can reach the electrical power supply with some slack in the
cable. The power cable is 5.8 metres (19 ft) long.
• To accommodate high in-rush currents, connect a time delay circuit breaker between the
facility power source and the load frame (refer to Table 2-3 on page 2-8).
For models 5988 and 5989 the mains voltage must be in a “WYE” configuration with
neutral and ground. A Delta configuration requires an external Delta-to-Wye
transformer rated to a minimum of 5kVa. A rating of 7.5kVa is recommended.
The connector on the power cable must be compatible with the power source. If
the power cable supplied with your system does not fit your power source outlet,
add a male plug to the cable that is compatible with the voltage. Observe the CEE
wire color code as follows:
• Brown - high (live)
• Light blue - low (neutral)
• Green and yellow - earth (ground)
Figure 4-3. 5-wire WYE 3-Phase Diagram
Phase A
Winding A
Winding B
Phase B
Winding C
Phase C
Neutral
Ground

4-5
Connect the System Components
The following procedure describes the connections for the basic components of an Instron
electromechanical system. If you purchased additional accessories for your system, you
need to refer to the documentation for those accessories for proper installation.
Warnings
1. Ensure that the power switch is set to Off (O) and the mains power cable to the machine
is disconnected.
2. Ensure that the Ethernet card in the computer that you intend to use for communication
with the frame is not connected to a network. You can connect the computer to a
network, but you must use a separate Ethernet card.
3. Connect the Ethernet crossover cable to the ETHERNET connector on the controller.
Connect the other end of the cable to the appropriate Ethernet card on the back of the
computer. Ensure that the connectors are fully engaged in their sockets.
4. Connect the load cell cable from the load cell to the LOAD connector on the controller.
Instron systems provide an option to measure strain. If your machine is enabled to
measure strain, then connect the extensometer to the STRAIN 1 connector on the
controller. Always use STRAIN 1 as the primary connection for strain. STRAIN 2 is
The load frame is supplied without a connector and with a 5-wire power cable
containing the following conductors:
• Black - U/L1/C/L+ - connect to Phase A
• Black - V/L2 - connect to Phase B
• Black - W/L3/C/L- - connect to Phase C
• Black - 4/N - connect to Neutral
• Green and yellow - connect to Earth (Ground)
Electrical Hazard - Do not connect power cables when the power is on. Turn the
power off to avoid hazardous voltages and component damage.

4-6 M10-16250-EN
another available option you can use to connect a second extensometer or other strain
device to the system.
5. Verify that the voltage setting for the machine is compatible with the facility’s voltage.
Refer to “Power Supply Compatibility” on page 4-3.
6. Ensure that the computer and monitor are set to the appropriate line voltage. Check the
switch on the back of the computer to verify the line voltage setting. If necessary, set the
switch to the proper line voltage. Check the back of the monitor for a line voltage switch
and ensure that it is properly set. If there is no switch on the monitor, then the monitor
automatically sets itself.
7. Connect the mains power cable for the machine to the IEC connector on the rear of the
machine and to the electrical power supply.
8. Refer to the documentation for the computer to connect the computer and monitor to the
electrical power supply.
9. Change the Windows Network TCP/IP settings for the dedicated Ethernet card to use a
fixed IP address. The following values are compatible with the system:
Contact your IT department if you are not sure how to do this.
10. The system is now ready to be turned on. Refer to “First Time Startup” on page 4-11
for instructions.
The connector labeled SERVICE on the controller is used only by Instron’s field service
engineers. No equipment should ever be connected via the SERVICE connector.
If installation of a system accessory requires additional cabling, refer to the documentation
for these devices for proper installation.
IP address 169.254.1.2
Subnet mask 255.255.255.0

4-7
Figure 4-4. 5982, 5984 and 5985 System Connections
GRN/YEL - Earth
BRN - Live
BLU - Neutral
Ground stud
Load cell
Controller
Supplemental ground
cable
Computer interface
connection
Load cell cable
Mains power cable
Ethernet
crossover cable
System ID
label

4-8 M10-16250-EN
Figure 4-5. 5988 and 5989 System Connections
BLACK - Live 1
BLACK - Live 2
BLACK - Live 3
BLACK - Neutral
GRN/YEL - Earth
Ground stud
Load cell
Controller
Supplemental ground
cable
Computer interface
connection
Load cell cable
Mains power cable
Ethernet
crossover cable
System ID
label

4-9
Figure 4-6. 5980 Controller Connections
Computer Interface
Connection (Ethernet)
Service
Input/Output (optional)
Strain 1
(optional)
Strain 2 (optional)
Load
Sync
(for use with AVE)
Service
Expansion port
(optional)

4-10 M10-16250-EN
Connect Optional Accessories
Instron electromechanical systems provide access for adding optional accessories that may
be necessary for your testing requirements. An options panel is located on the machine that
enables you to use the following accessories:
• Lamp - 12 Vac 2A rated outlet for optional light accessory.
• Pip jack - Connects a remote recorder pen pipping device, such as an event marker or an
incremental extensometer, to the system.
• Interlock capability (optional) - The interlock capability is provided with certain custom
protective shields. The interlock prevents the system from working when the door is
open. The standard protective shield does not include this functionality.
• Grip control - 9 pin D connector for the optional pneumatic grip control function. This
function enables you to apply a specified pre-tension to the specimen when using cord
and yarn grips.
The following graphic displays all options on the Options panel. If any of these options are
not purchased with the system, then these connectors are not enabled and have black
coverings.
Figure 4-7. 5980 Options Panel
Grip Control
Lamp
PIP
Door shield
interlock
(optional) Optional
mode

4-11
First Time Startup
First Time Startup
When the testing system is installed, you need to configure the Bluehill software so that it
can communicate with the hardware. When the entire system is assembled and the software
is started for the first time, a configuration wizard displays to let you make the choices that
are needed to configure the system.
1. Ensure that all cables are properly installed and securely connected.
2. Turn the power switch for the machine to the On (I) position. Ensure that the POWER
indicator light illuminates.
3. Power on all other system components (e.g. computer and any other accessories).
4. Start the Instron Bluehill software. The first time the software runs, the configuration
wizard displays.
5. Follow the instructions in the wizard screens to:
• select the controller type and frame model
• enter the System ID (located on a label on the frame)
• enter the MAC address (located on a label adjacent to the Ethernet connector on the
controller)
• enter any additional information (e.g. service contract number)
• select any accessories that are installed
If you need to change any of these settings at a later time, when you purchase an additional
accessory for example, go to the Admin tab in Bluehill software.

4-12 M10-16250-EN

5-1
Chapter 5
Maintenance
• Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
• General Maintenance Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
• Troubleshooting for Load Cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
• Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Warnings
Preventive Maintenance
Preventive maintenance is the periodic inspection, cleaning, and lubrication of the test
system. The following sections provide guidelines for preventive maintenance.
To ensure that the frame continues working at its optimal performance, it is recommended
that the machine receive an annual service check. Instron’s Service department can perform
this annual service, and replace any damaged or worn parts to ensure that your machine
operates to its stated specifications.
Instron offers many service agreements that provide a variety of services, including annual
service visits. Contact your local Instron office for details on a service agreement or contract
that best matches your needs.
Hazard - Only qualified personnel, trained to service Instron machines, should
perform all internal maintenance requirements.
Instron machines must operate within stringent specifications. In order to keep the
system working within the stated specifications, a professionally trained and qualified
technician must perform most maintenance procedures. If unqualified personnel
perform any maintenance procedures not described in this manual, the machine may not
perform to its stated specifications.

Chapter: Maintenance
5-2 M10-16250-EN
Daily Maintenance Checks
Before operating the system each day, ensure:
• All cable connections are tight and secure.
• All grips, fixtures and accessories are free of dirt, damage and deformation.
• The load frame is level. If an adjustment is necessary, refer to “Level the Load
Frame” on page 4-1.
• Signal and power cables have adequate slack to prevent excessive strain on connectors.
• All cables are free of wear and chafing. Re-route the cables if necessary, and replace any
damaged cables.
• After turning on the system, make sure that power is adequately supplied to the
electronics.
Correct any problems before you operate the testing system. If you require assistance,
contact your local Instron Service department.
Periodic Inspections
Every six to twelve months, perform the following inspections:
• Visually inspect the machine for any loose fittings. Check the limit stops, cable
connections, and connections for any accessories that are attached to the machine.
Tighten any loose connections that you may find.
• Operate the crosshead through the full range of motion. It should move smoothly with
no unusual noise, or erratic motion. If it does not, refer to Table 5-1 on page 5-3 for
lubrication recommendations.
• Test the limit stops to ensure they are in working order. Refer to “Test Limit Stops” on
page 5-8.
• If you have any additional safety equipment added to the machine, test the equipment to
ensure it is in working order.
If you notice any problems resulting from these inspections, contact Instron’s Professional
Services department for immediate assistance.

5-3
Cleaning
Caution
Do not clean with solvents or abrasive cleaners. Some household or commercial
cleaners can react with painted surfaces or panel markings.
Do not apply excessive amounts of detergent cleaner. It may seep into electrical
circuits within the base and cause equipment failure.
Do not use too much oil. It attracts abrasive particles that may accelerate wear.
Use low pressure air to blow dust. Do not direct the air stream directly at sensitive
components.
It is recommended that the machine be cleaned weekly, or more often if it is operating in a
dusty or dirty environment.
To clean the load frame, wipe exterior surfaces of the load frame with a moist cloth.
If your machine has a maximum capacity of 50 kN or greater (all floor models and some
table models) and if the central mounting area on the base beam is exposed (no base adapter
is in place) then you must regularly lubricate the mounting area with oil to prevent
corrosion. If you regularly use a base adapter, then you do not need to lubricate this area
(refer to “Lubrication” on page 5-3).
Lubrication
Table 5-1. Lubrication Requirements for Ballnuts
Recommended Lubricant Interval Instron Part Number
Lithium based water resisting grease -
NLGI Class 2
(DIN51825 class K2k LS2)
Equivalents:
Lubriplate: Lubriplate 1200-2
Mobil: Mobilux® 2
BP: Energrease® LS2
Shell: Alvania® R2
1000a hours or 36
months of
operating timeb
105-1-1057
(small can of lubricant)
a. If the system is used more than 100 hours per month, inspect the lubricated area periodically and
increase lubrication frequency as required.
b. Operating time is defined as time of crosshead movement, not the length of time the system has been
powered on.

5-4 M10-16250-EN
The following areas of the machine will require periodic lubrication:
• Ballscrews - The ballscrews are lubricated via a ballnut that is located on the crosshead
where the ballscrew intersects the crosshead. As the crosshead moves up and down, the
ballnut disperses a thin layer of lubricant over each ballscrew as the ballscrew passes
through the ballnut. Periodically, the ballnut must be filled with lubricant to ensure that
the ballscrews remain well lubricated. The ballnut must be maintained and filled in
accordance with Table 5-1 on page 5-3.
Inspect the ballscrew and lubricate more frequently if any of the following conditions
exist:
• There is high-load or high-speed testing.
• There is long-term, continuous movement of the crosshead.
• The system operates in a dirty environment.
• There are high-load cycling tests.
• Guide columns - The guide columns require only a thin film of lubrication. It is
recommended that the machine be re-lubricated every two years.
• Mounting surfaces - as mentioned in the Cleaning section, the mounting area in the
base of the floor models must also be lubricated if it is regularly exposed (no base
adapter installed). Use a lint-free cloth and the same lubricants and schedule used for the
ballscrews and guide columns.
The top and bottom ballscrew bearings are sealed and should never need lubrication.

5-5
Ballscrew Ballnuts
Warnings
The ballnuts are located on the crosshead where the ballscrews intersect with the crosshead.
To lubricate the ballscrew ballnuts:
1. Turn the power switch to the Off (O) position and disconnect the power cable from the
main power source. Verify that the POWER indicator light is not illuminating.
2. Detach the bottom ballscrew cover from the crosshead and slide it to the frame base.
Refer to Figure 5-1 on page 5-6 to locate the ballnut nipple inside the column cover.
3. Use a grease gun to apply the grease through the ballnut nipples on both columns as
shown in Figure 5-1. It is not necessary to remove the guide column covers.
4. Fill the ballnuts until grease begins to ooze from the top of the nut. Wipe away the
excess grease.
5. Re-attach the bottom ballscrew cover to the crosshead.
6. Re-connect the power cable to the main power source and turn the power switch to the
On (I) position. Verify that the POWER indicator light illuminates.
7. Use the jog controls to move the crosshead over the full stroke of the frame to distribute
the grease in the ballnut and coat the ballscrew shaft. The TEST IN PROGRESS
indicator light illuminates when the crosshead is moving.
Entanglement Hazard - Keep hair and loose clothing clear of the ballscrews
during this procedure.
This procedure requires that you remove the bottom ballscrew cover, exposing a section
of the ballscrew. Ensure that the power supply is disconnected during the procedure and
reinstall the ballscrew covers immediately after the procedure is completed.

5-6 M10-16250-EN
Figure 5-1. Ballscrew Lubrication Points
Ballscrew
Ballnut
nipple
Crosshead
Guide column
cover
Ballnut
Ballscrew cover

5-7
Guide Columns
Warning
Warnings
The guide columns should also be lubricated periodically. Lubricate the guide columns
when you lubricate the ballscrews, using the same lubricant.
To lubricate the guide columns:
1. Turn the power switch to the Off (O) position and disconnect the power cable from the
main power source. Ensure that the POWER indicator light does not illuminate.
2. Detach the ballscrew covers from the crosshead and slide the covers away from the
crosshead. Refer to Figure 5-2 on page 5-8 to locate the guide column inside the
column cover.
3. Reaching behind the ballscrew, apply a thin film of lubricant with a soft, lint-free cloth
over the entire length of each column.
4. Re-attach the ballscrew covers to the crosshead.
5. Re-connect the power cable to the main power source and turn on the system. Verify that
the POWER indicator light illuminates.
This procedure should only be performed by personnel who have received
detailed training either at the Instron training center or on site by a qualified
Instron service engineer.
of the ballscrew.
Entanglement Hazard - Keep hair and loose clothing clear of the ballscrews
during this procedure.
of the ballscrew. Ensure that the power supply is disconnected during the procedure and
reinstall the ballscrew covers immediately after the procedure is completed.

5-8 M10-16250-EN
6. Use the jog controls to move the crosshead over the full stroke of the frame to ensure
that the crosshead moves smoothly. The TEST IN PROGRESS indicator light
illuminates when the crosshead is moving.
7. Before you do any testing, perform the procedure “First Time Startup” on page 4-11.
General Maintenance Procedures
General maintenance procedures are the procedures that you can perform should it become
necessary. These procedures do not require an Instron service technician, although
assistance is available. Contact your regional Instron office or check our web site at
www.instron.com for assistance.
Test Limit Stops
It is recommended that you periodically test both the first and second level limit stops on the
load frame.
1. Ensure that the system is on and the crosshead is stationary.
2. Secure one of the limit stops (either the upper or lower limit stop) to the limit switch rod.
3. Firmly hold the yellow part of the limit stop to gently move the stop either downward (in
compression) or upward (in tension) about 3 mm (1/8 in).
Figure 5-2. Lubricating the Guide Columns on Floor Frames
Crosshead
Guide column
Ballscrew

5-9
Troubleshooting for Load Cells
4. A first level limit warning displays on the computer.
5. Repeat Step 3 moving the limit stop another 3 mm (1/8 in) in the same direction.
6. A second level limit warning and frame disabled warning displays on the computer.
The frame disabled warning indicates that the limit stops are working correctly. If the
frame disabled warning does not display, contact your local Instron service office for
assistance.
After testing the limit stops, you need to re-enable the load frame.
1. In Bluehill software, click in the console area to open the Load Frame Settings dialog.
2. Click the Frame tab.
3. Click Enable frame.
4. Click Done to close the dialog box. The FRAME READY light on the control panel
illuminates when the frame is enabled.
Troubleshooting for Load Cells
Instron load cells, in general, are electrically calibrated, self-identifying and rationalized.
Approximate resistances are given that can verify a possible broken gauge, or a faulty
connector or cable.
If a strain gauge in a cell has been badly overstressed, but still maintains its electrical
continuity, the cell may show a higher than normal amount of creep. If a gauge has become
improperly bonded due to degradation in use, the cell may exhibit a combination of general
instability in its balance point, together with a large amount of creep. Difficulties of this sort
rarely appear as an instability in the calibration of the cell.
If a load cell has been overloaded, the load-sensitive member may be permanently deformed
to the extent that the proper dimensional alignments inside the cell are no longer maintained.
For example, if the position of the central spindle is changed, this can result in the balance
point shifting abruptly as the cell is loaded or unloaded.
To check the load cell, substitute another cell to re-check the test results carefully. If your
results differ significantly from the original test results, then the original load cell may be
damaged. However, many of the symptoms described above can also arise from a faulty load
sensor conditioner, recorder, or possibly a mechanical adjustment.
If you suspect that a cell may be damaged, contact your local Instron Service office to
arrange returning the load cell for analysis and possible repair.

5-10 M10-16250-EN
Spare Parts
Ancillary Parts - Frames with a Single Test Space
The following sections list the parts supplied with each of the 5980 Series load frames.
5982 Frame
Table 5-2. 5982 Ancillary Parts
Description
Part
Number Quantity Purpose
Cable Ethernet Cat5E 10ft
Crossover
144-1-1052 1 Connects the frame controller to the
computer
Hex wrench key set,
1.5 to 10 mm
80-1-1011 1 Tools for maintaining the frame and
installation of accessories
Fuse, 2A Slo-blo, 6.3 x 32mm
glass
27-2-13 1 Protection from electrical surges
Cable clip, 6-12 mm 11-6-60 4 Secures cables to the frame
Nut, M5 T-slot clip 52-59-1011 4 Installing accessories onto the column
cover
Accessories slot T-nut T1697-1307 4 Installing accessories onto the column
cover
3 MTS Ground cable A712-213 1 Used to connect the frame to a
suitable ground where the mains
power supply is not grounded
Locating ring T1335-1048 1 Locating ring for base - 40mm
diameter for M30 thread
Screw, M10 x 160 201R250 6 Attaches load cell to crosshead
Compression spring
3/4OD x 2 in length
66-4-5 1 Removes slack on lower grips with no
checknut
Tool spanner, open 19 mm a/f 80-51-1003 1 Tool for tightening lock nuts on load
string
Retainer clip for 0.5 in diameter pin T1223-1053 2 Prevents the grip coupling pin from
sliding out during testing
Retaining pin, grip coupling T29-515 2 Secures the grip coupling

5-11
Spare Parts
5984 and 5985 Frames
5988 Frame
Table 5-3. 5984 and 5985 Ancillary Parts
Description
Part
Crossover
computer
Hex wrench key set,
1.5 to 10 mm
glass
cover
cover
3 MTS Ground cable A712-213 1 Used to connect the frame to a
Locating ring T1208-1147 2 Locating ring adapter - converts
60mm to 40mm for base
Locating ring type 2 T1335-1052 2 Locating ring for load cell- 60mm
Screw, M20 x 200 201R374 4 Attaches load cell to crosshead
Tool socket driver, 17mm key 80-3-51 1 Tool for removing M20 screws
Tool spanner, open 19 mm a/f 80-51-1003 1 Leveling the load frame
Description
Part
Crossover
computer
Hex wrench key set,
1.5 to 10 mm

5-12 M10-16250-EN
5989 Frame
glass
cover
cover
10 MTS Ground cable A712-213-3 1 Used to connect the frame to a
Locating ring type 2 T1335-1052 1 Locating ring for load cell- 60mm
Superbolt nut, M48 x 2P 52-2-75 1 To attach and preload load cell
Draw bar M48 x 2 RH T620-505 1 Used with superbolt nut to attach load
cell to crosshead
Transducer cable assembly, 2.5 m A1735-1360-1 1 Load cell extension cable
Description
Part
Description
Part
Crossover
computer
Hex wrench key set,
1.5 to 10 mm
glass
Nut, M5 T-slot clip 52-59-1011 6
cover

5-13
Spare Parts
Ancillary Parts - Frames with a Second Test Space
For frames with a second test space, the following table lists the ancillary parts supplied in
addition to the standard parts kit.
10 MTS Ground cable A712-213-3 1 Used to connect the frame to a
Locating ring type 2A T620-512 1 Locating ring for load cell- 82mm
Superbolt nut, M72 x 3P 52-2-74 1 To attach and preload load cell
Draw bar M72 x3 RH T620-479 1 Used with superbolt nut to attach load
cell to crosshead
Transducer cable assembly, 2.5 m A1735-1360-1 1 Load cell extension cable
Description
Part
Table 5-6. Second Test Space Ancillary Parts
Description
Part
Crosshead Clevis - Type D T1209-1138 1 Connects grips and fixtures to top of
crosshead
Screw, M10 x 30 201V55 6 To secure clevis type D
Locating ring T1335-1048 1 Load cell locating ring
Compression spring
3/4OD x 2 in length
66-4-5 1 Removes slack on lower grips with no
checknut
Retainer clip for 0.5 in diameter pin T1223-1053 1 Prevents the grip coupling pin from
sliding out during testing
Retaining pin, grip coupling T29-515 1 Secures the grip coupling

5-14 M10-16250-EN

Index-1
I n d e x
A
accessibility . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
accessory mounting dimensions . . 2-17 to 2-25
accreditations. . . . . . . . . . . . . . . . . . . . . . . . 2-6
B
ballscrew ballnuts
lubricating . . . . . . . . . . . . . . . . . . . 5-3 to 5-8
C
CE accreditation . . . . . . . . . . . . . . . . . . . . . 2-6
ceiling clearance . . . . . . . . . . . . . . . . . . . . . 2-5
checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
checks
daily maintenance. . . . . . . . . . . . . . . . . . . 5-2
chromium. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
connecting optional accessories . . . . . . . . 4-10
connecting system components. . . . . 4-5 to 4-9
contact information . . . . . . . . . . . . . 1-10, 2-27
crosshead
travel limits, testing . . . . . . . . . . . . . . . . . 5-8
customer responsibilities . . . . . . . . . . . . . . . 2-1
D
daily maintenance checks . . . . . . . . . . . . . . 5-2
digital phone lines . . . . . . . . . . . . . . . . . . . . 2-5
dimensions
accessory mounting . . . . . . . . . . 2-17 to 2-25
documentation . . . . . . . . . . . . . . . . . . . . . . . 2-3
E
environmental conditions . . . . . . . . . . . . . . 2-5
environmental impact . . . . . . . . . . . . . . . . . 2-7
environmental specifications. . . . . . . . . . . . 2-6
F
floor loading. . . . . . . . . . . . . . . . . . . . . . . . . 2-4
frame
optional combinations. . . . . . . . . . . . . . . 2-10
G
guide columns
lubricating . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
I
impact, environmental . . . . . . . . . . . . . . . . . 2-7
initial operation of the system . . . . . . . . . . . 2-3
installation
connecting optional accessories . . . . . . . 4-10
connecting system components. . . 4-5 to 4-9
Instron’s responsibilities . . . . . . . . . . . . . . 2-3
leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Instron
contact information . . . . . . . . . . . . 1-10, 2-27
product support . . . . . . . . . . . . . . . . . . . . 1-10
Instron responsibilities . . . . . . . . . . . . . . . . . 2-2
insurance
customer’s responsibilities . . . . . . . . . . . . 2-2
Instron’s responsibilities . . . . . . . . . . . . . . 2-2
L
labeling
safety and information . . . . . . . . . 1-8 to 1-9
lead, brominated fire retardants . . . . . . . . . . 2-7
leveling the load frame. . . . . . . . . . . . . . . . . 4-1
limit stops
testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
load cells
troubleshooting . . . . . . . . . . . . . . . . . . . . . 5-9
load frame
leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
optional combinations. . . . . . . . . . . . . . . 2-10

M
Index-2 M10-16250-EN
lubricating
ballscrew ballnuts. . . . . . . . . . 5-3, 5-5 to 5-6
lubricating the guide columns . . . . . . . . . . . 5-7
lubrication . . . . . . . . . . . . . . . . . . . . . 5-3 to 5-8
M
maintenance
cleaning . . . . . . . . . . . . . . . . . . . . . 5-2 to 5-3
daily checks . . . . . . . . . . . . . . . . . . . . . . . 5-2
inspection . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
lubricating the ballscrew ballnuts. 5-3, 5-5 to
5-6
lubricating the guide columns . . . . . . . . . 5-7
lubrication . . . . . . . . . . . . . . . . . . . 5-3 to 5-8
testing limit stops . . . . . . . . . . . . . . . . . . . 5-8
maintenance schedule . . . . . . . . . . . . . . . . . 5-1
materials disposal . . . . . . . . . . . . . . . . . . . . 2-2
moving load frame into vertical position
using a crane. . . . . . . . . . . . . . . . . . 3-5 to 3-6
using a forklift . . . . . . . . . . . . . . . . 3-6 to 3-8
moving, dual column frames
frame base method . . . . . . . . . . . . 3-9 to 3-10
moving, frames
crane method . . . . . . . . . . . . . . . . . . . . . 3-12
crosshead method. . . . . . . . . . . . 3-11 to 3-12
N
network access. . . . . . . . . . . . . . . . . . . . . . . 2-5
network drops . . . . . . . . . . . . . . . . . . . . . . . 2-5
O
optional accessories
connecting . . . . . . . . . . . . . . . . . . . . . . . 4-10
optional frame combinations. . . . . . . . . . . 2-10
P
power requirements . . . . . . . . . . . . . . . . . . . 2-8
power supply . . . . . . . . . . . . . . . . . . . . . . . . 2-4
preparation checklist . . . . . . . . . . . . . . . . . 2-26
preventive maintenance
cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
daily checks. . . . . . . . . . . . . . . . . . . . . . . . 5-2
inspection . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
lubrication . . . . . . . . . . . . . . . . . . . 5-3 to 5-8
product support. . . . . . . . . . . . . . . . . . . . . . 1-10
R
remote system access . . . . . . . . . . . . . . . . . . 2-5
responsibilities
customer . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Instron . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
righting a load frame
using a crane . . . . . . . . . . . . . . . . . 3-5 to 3-6
using a forklift. . . . . . . . . . . . . . . . 3-6 to 3-8
routine maintenance . . . . . . . . . . . . . . . . . . . 2-5
S
safety and information labeling . . . . 1-8 to 1-9
safety limits
testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
site preparation checklist . . . . . . . . . . . . . . 2-26
site requirements . . . . . . . . . . . . . . . . . . . . . 2-3
specifications
environmental . . . . . . . . . . . . . . . . . . . . . . 2-6
power requirements. . . . . . . . . . . . . . . . . . 2-8
weight, optional configuration models . . 2-16
weight, standard configuration models. . 2-16
support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
system components
connecting. . . . . . . . . . . . . . . . . . . 4-5 to 4-9
system power requirements . . . . . . . . . . . . . 2-8
T
table loading. . . . . . . . . . . . . . . . . . . . . . . . . 2-4
technical support . . . . . . . . . . . . . . . . . . . . 1-10
telephone access. . . . . . . . . . . . . . . . . . . . . . 2-5
testing safety limits . . . . . . . . . . . . . . . . . . . 5-8
transferring load frame into vertical position
using a crane . . . . . . . . . . . . . . . . . 3-5 to 3-6

Index-3
U
transporting procedures, frames
crane method . . . . . . . . . . . . . . . . . . . . . 3-12
crosshead method. . . . . . . . . . . . 3-11 to 3-12
frame base method . . . . . . . . . . . . 3-9 to 3-10
travel limits
testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
troubleshooting load cells . . . . . . . . . . . . . . 5-9
U
unpacking
frames. . . . . . . . . . . . . . . . . . . . . . . 3-3 to 3-4
uprighting a load frame
using a crane. . . . . . . . . . . . . . . . . . 3-5 to 3-6
V
voltage requirements . . . . . . . . . . . . . . . . . . 2-8
W
weight specifications
optional configuration models . . . . . . . . 2-16
standard configuration models. . . . . . . . 2-16

5980 dual column floor frames system support

5980 dual column floor frames system support

More Related Content

What's hot (20)

Similar to 5980 dual column floor frames system support (20)

More from Muhammed Fuad Al-Barznji (20)

Recently uploaded (20)

5980 dual column floor frames system support