6_line_communication.ppt
- 1. Line Communication 1. Two Wire Transmission Lines - Parallel Wire Line - Twisted Pair Wires - Coaxial Line 2. Equivalent Circuit of a Transmission Line 3. Velocity Factor in a Line 4. Losses in a Line 5. Cable System 6. Optic Fibre System & Components of Fibre Optic Equipment 7. Optical Fibre – Types of Optical Fibre 8. Principle of Optic Fibre 9. Important Aspects – Numerical Aperture, Attenuation and Dispersion 10. Advantages and Disadvantages of Optic Fibres Created by C. Mani, Principal, K V No.1, AFS, Jalahalli West, Bangalore
- 2. Line Communication: The simplest and the oldest mode of communication from point-to-point in contact through transmission lines or wires is called ‘line communication’. The main line communication channels are: (i) Two wire transmission lines (ii) Coaxial cables (iii)Optical fibres Two Wire Transmission Lines: The most commonly used two wire lines are: (a) Parallel wire line (b) Twisted pair of wires and (c) Coaxial line Parallel Wire Line: Insulation It is also known as balanced line. It resembles a ribbon. It is commonly used to connect an antenna with the TV receiver. It suffers from interferences and losses. If the conductor separation is nearly equal to half wave length of the operating frequency of the signal, the system of wires may start radiating the signal. Parallel wire lines are not suitable for microwaves. Conductors
- 3. Twisted Pair of Wires: A twisted pair of wires consists of two insulated copper wires twisted around each other at regular intervals. If the wires run parallel without twisting, then the electrical interference will be more for the wire close to the source of noise than the wire away from the source of noise. As a result of this, a distorted signal is available at the receiving end. So, to minimize the electrical interference, two wires are twisted around each other. Twisted pair wires are used to connect telephone systems. Usually many twisted pairs parallel to each other are grouped in the form of a bundle which is encased in a protective sheath. In case of twisted pair wires, signals having frequency range 100 Hz to 5 MHz are transmitted. Outer Insulation Protective shield (Wire mesh) Twisted pairs
- 4. Advantages: (i) The signals can travel several kilometers without any amplification in a telephone system when twisted pair wires are used. (ii) Both analogue and digital signals can be transmitted. (iii)It is a cheap mode of communication. Disadvantages: (i) The signal becomes weak when it travels a very large distance through a twisted pair of wires. As a result, transmission becomes faulty. (ii) Telephone lines run overhead, so they can be broken during storm, etc. Coaxial Line: It is also called unbalanced line. Such a line resembles a rounded cable. It is commonly used by TV Cable operators. Outer Insulation Conductor - II in mesh form Conductor - I Inner Insulation
- 5. The inner and outer conductors are separated with the help of low dielectric. The common insulations are Polyethylene and Teflon. Coaxial cables can be gas filled also. To reduce flash over between the conductor handling high power, nitrogen gas is used in the cable. Dry air can also be used under high pressure to avoid moisture in the cable. These cables can find wide application for frequencies between 1 GHz and 20 GHz. Advantages: (i) Coaxial cable is well protected than an ordinary twisted pair of wires, so communication through cables is more efficient than through the twisted pairs. (ii) The speed of transmission of signals is more than that of twisted pairs. (iii)Electrical signals of higher frequencies (100 kHz to 500 kHZ) are transmitted through the cables than through the twisted pair wires. It is also used to interconnect transmitter and an earthed antenna. Such cables are shielded i.e. outer conductor surrounds the insulated inner wire and the outer conductor is always earthed. These cables do not suffer from radiation problems and be used for microwave and UHF region.
- 6. ≡ ≡ Insulation C G C G C C L L L L R L R L R A two wire line consists of conductors and dielectric between them. The line has some resistance (or conductance), inductive reactance and capacitive reactance (or susceptance). A dielectric can not be an ideal insulator and so some leakage current always flows through it which is considered to be due to shunt conductance G. At radio frequency operations, the inductance of line is more effective than the resistance of line and capacitive susceptance is also significant than shunt conductance. So, at RF such resistances and shunt conductances can be ignored resulting into simple LC circuit. A two wire line has some input impedance which depends upon type of line, length of line, termination at the other end, etc. This input impedance is known as ‘reference impedance or characteristic impedance’ (Z0). Equivalent Circuit of a Transmission Line:
- 7. At voice frequency, expression for characteristic impedance is Z0 = R + jωL G + jωC At radio frequency, expression for characteristic impedance is Z0 = L C (R and G are insignificant) Characteristic impedance can be defined as the impedance measured at the input of a line of infinite length. Practically this impedance depends upon the size and spacing of the conductors as well as dielectric constant of the insulator separating them. For a parallel – wire line, Z0 = 276 √k log 2 S d For a coaxial line, Z0 = 138 √k log D d d D d S
- 8. Velocity Factor of a Line: Velocity factor (v.f) of a cable is the ratio of reduction of speed of light in the dielectric of the cable. c v = √k (where c is speed of light and k is dielectric constant) By definition, v = (v.f) c So, v.f = 1 / √k For a line, velocity factor is generally of the order of 0.6 to 0.9 Losses in a Line: Different types of lines cause different amount of energy losses. These losses can be due to Joule’s heating in conductors, dielectric heating of insulation, radiation, etc. Joule’s Heating is given by H = I2Rt Current in the line depends upon frequency to be handled. Frequency alters the skin effect which changes the capacitive reactance ( 1 / 2πνC ) and inductive reactance ( 2πνL ) changing the circuit current and hence the energy losses change. Dielectric losses are proportional to the voltage across the insulation. These losses increase with frequency. Dielectric heating is inversely proportional to the characteristic impedance for any power transmitted by the line. Parallel lines cause radiation losses. Increase in frequency increases radiation losses. Coaxial cables have less radiation losses compared to parallel lines.
- 9. Cable System: A practical cable system consists of a tube carrying many simple coaxial cables. They are more commonly used compared to flat cables. A coaxial cable consists of a conductor covered with a suitable insulation. A shield wire is wrapped on this insulation which serves as the second conductor also. The shield wire is then again covered with a suitable insulation which also serves as a protection against mechanical injuries. A typical cable used in communication system is used for multiple channels. A large channel system with 10,500 channels is much cheaper than equivalent number of small channel systems (say 3 x 3500 channels). Conductor Insulators Shield wire or mesh (conductor) Insulator Tube Spacers A cable is a source of loss of energy of a signal causing attenuation in signals as they travel along the cable. A signal booster i.e. amplifying repeater is placed at the required distance intervals. A cable further deviates the frequency and phase response of a signal. This deviation in signal has to be set right with the help of fixed type or variable type equalizers.
- 10. Optic Fibre System: Optical communication is the mode of transmitting information in the form of a sort of light beam. Optical fibre link like microwave link transmits the output from the digital source. The bit stream (zeros and ones) can be used directly to turn a laser or and off to send light pulses down the fibre cable. Line Terminal Equipment Repeater or Regenerator Line Terminal Equipment Repeater or Regenerator BIT stream BIT stream Optical signal Optical Fibre Cable Optical Fibre Cable Optical signal Optical Fibre Cable
- 11. Components of Fibre Optic Equipment: 1. Light Source (LD or LED): They are p-n junctions. Light from LED is produced by spontaneous emission whereas light from an LD is made by stimulated emission. LED has an incoherent output and wide spectrum but it has higher reliability, simpler drive circuit, lower temperature sensitivity, immunity to reflected light and low cost. LD has an output which is coherent and therefore has a very narrow spectrum. It has high output power and high coupling efficiency. 2. Amplifiers: Semiconductor amplifiers or doped fibre amplifiers are used to limit fibre losses and to increase repeater spacing. They are also known as repeaters because they can directly boost the signal just prior to detection. 3. Modulators: Modulation of a light source can be done by direct modulation of direct current supplying the source or by using an external modulator following the source. The simplest form of direct modulation is to change the light biasing current above and below the threshold value to turn the laser on and off to obtain digitalisation (0 and 1). 4. Filters: They are essential components to minimise the cross talk between channels. 5. Light Detectors: Light emerging from the end of an optical fibre link must be detected and converted in to electronic pulses for further processing so that the transmitted information can be received.
- 12. Optical Fibre: Buffer Jacket Silicon Gel Cladding (Glass of Plastic) (n2) Core (Glass / Plastic / Silica) (n1) n1 > n2 1. Core: It is made of glass / silica / plastic of refractive index (say n1) with approximate diameter of 10 to 100 μm. 2. Cladding: It is made of glass or plastic with refractive index n2 (n2 < n1) with approximate diameter of 100 to 400 μm. Cladding is of two types: Step-index fibre in which the refractive index changes abruptly; Graded-index fibre in which the refractive index changes gradually. 3. Buffer Jacket: It is plastic coating which houses the core-cladding and provides safety and strength.
- 13. Types of Optical Fibre: Input Light Pulse Output Light Pulse Multi mode fibre Single mode fibre 1. In multi mode optical fibre, the core diameter is about 50 μm. The signal is transmitted in multiple modes. Attenuation is higher in this mode. 2. In single mode optical fibre, the core diameter is about 8 to 10 μm which is approximately same as the wavelength of the light used. Only one mode propagates in this fibre. Attenuation is lower and the maximum bit rate is higher. Fibre Bending: Whenever a fibre is bent, some of the energy with in the core can escape into region outside the fibre. This loss of energy increases as the radius of curvature of bend decreases.
- 14. Principle / Action of Optical Fibre: Optical fibre works on the principle of total internal reflection. When light falls on the interface separating the fibre and coating at an angle which is greater than the critical angle, multiple total internal reflections take place. The light travels the entire length of the fibre and comes out of the other end of the fibre without any loss in its intensity. i>ic Cladding (n2 = 1.5) Core (n1 = 1.7) Incident Light Transmitted Light Optic Pipe: It is a bundle of thousands of optical fibres packed in such a way that the free ends on both sides are at the same relative positions.
- 15. Important Aspects of Fibre Optics: 1. Numerical Aperture (NA): For Total Internal Reflection, light should enter the fibre at an angle θ in accordance with core of acceptance angle θc. Numerical Aperture depends on diameter of the core. It decreases as the diameter of core decreases and vice versa. Typical value of NA for a 50 μm core cable is 0.2 and it is 0.1 for 10 μm cable. NA = sin θc = n1 2 – n2 2 2. Attenuation: It basically means power loss or loss of information strength. Standard wavelengths of operation of optical fibres are 1.3 and 1.55 μm. The lowest loss silica fibres operate at 1.55 μm with minimum attenuation of about 0.2 dB/km. 0.2 1550 nm Attenuation Coefficient (dB/km) Wavelength (nm) 0
- 16. 3. Dispersion: As the optical pulses travel forward in the optical fibre, the pulses are broadened due to dispersion and the adjacent pulses may overlap. So, dispersion limits the distance of data transmission and transmission speed of data. Laser has a narrower line width and hence dispersion will be the least. Dispersion depends on fibre dimensions i.e. core diameter. It is also due to frequency dependence of refractive index of the fibre material. Advantages of Optical Fibres: 1. Optical fibres are the best for wavelength multiplexing i.e. innumerable signals of differing but nearby wavelengths can be sent along the same fibre. A pair of optical fibres can carry 3000 telephone calls simultaneously whereas only dozens of telephone calls can be carried by a pair of copper wires and that also by special methods only. 2. They are the best suited for digital transmission and switching systems. 3. A normal optic fibre cable is 1/6th in diameter as compared to coaxial cable. 4. Optic fibre communication is free from electromagntic interference and noise.
- 17. 5. Optical fibres are virtually free from losses. The intensity of the information transmitted by electric current flowing in copper wires become weak. But, the messages, data or picture sent through optical fibres remain undisturbed and hence can be transmitted through thousands of kilometers. 6. Optical communication can not be jammed as easily as radio waves can be jammed. 7. Light has higher frequency than electric current and so optical fibres can transmit higher band widths. 8. Optic fibres are becoming economical day by day. Disadvantages of Optical Fibres: 1. Optical fibres are costly. 2. Only skilled engineers can handle the technology. 3. Glass fibres are easily broken when compared to copper wires, so they require extra care when installed.