Advanced motion controls 30a8i
0 likes111 views
The document provides specifications for the Analog Servo Drive 30A8I. It is a PWM servo drive designed to drive DC motors from a single power supply between 20-80VDC. It can provide up to 30A of peak current and 15A of continuous current. It has adjustable current limits, loop gains, and other parameters. It also has protections against overvoltage, overcurrent, and short circuits.
Advanced motion controls 30a8i
- 1. Analog Servo Drive 30A8I Description Power Range The 30A8I PWM servo drive is designed to drive brush type DC motors at a high switching frequency. A single red/green LED indicates operating status. The drive is fully protected against over-voltage, over- current, over-heating and short-circuits across motor, ground and power leads. Furthermore, the drive can interface with digital controllers or be used stand-alone and requires only a single unregulated DC power supply. Loop gain, current limit, input gain and offset can be adjusted using 14-turn potentiometers. The offset adjusting potentiometer can also be used as an on-board input signal for testing purposes. Peak Current 30 A Continuous Current 15 A Supply Voltage 20 - 80 VDC Features Optical Isolation Between High & Low Power Signals Four Quadrant Regenerative Operation DIP Switch Selectable Modes Adjustable Current Limits High Switching Frequency Differential Input Command Digital Fault Output Monitor On-Board Test Potentiometer Offset Adjustment Potentiometer Adjustable Input Gain Drive Status LED Directional Inhibit Inputs for Limit Switches MODES OF OPERATION Current Tachometer Velocity Voltage IR Compensation COMMAND SOURCE ±10 V Analog FEEDBACK SUPPORTED Tachometer COMPLIANCES & AGENCY APPROVALS UL cUL CE Class A (LVD) CE Class A (EMC) RoHS ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 2. Analog Servo Drive 30A8I BLOCK DIAGRAM Information on Approvals and Compliances US and Canadian safety compliance with UL 508c, the industrial standard for power conversion electronics. UL registered under file number E140173. Note that machine components compliant with UL are considered UL registered as opposed to UL listed as would be the case for commercial products. Compliant with European CE for both the Class A EMC Directive 89/336/EEC on Electromagnetic Compatibility (specifically EN 61000-6-4:2001, EN 61000-6-2:2001, EN 61000-3-2:2000, and EN 61000-3-3:1995/A1:2001) and LVD requirements of directive 73/23/EEC (specifically EN 60204-1), a low voltage directive to protect users from electrical shock. RoHS (Reduction of Hazardous Substances) is intended to prevent hazardous substances such as lead from being manufactured in electrical and electronic equipment. ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 3. Analog Servo Drive 30A8I SPECIFICATIONS Power Specifications Description Units Value DC Supply Voltage Range VDC 20 - 80 DC Bus Over Voltage Limit VDC 86 Maximum Peak Output Current1 A 30 Maximum Continuous Output Current A 15 Maximum Power Dissipation at Continuous Current W 60 Minimum Load Inductance (Line-To-Line)2 μH 200 Switching Frequency kHz 22 Control Specifications Description Units Value Command Sources - ±10 V Analog Feedback Supported - Tachometer Modes of Operation - Current, IR Compensation, Tachometer Velocity, Voltage Motors Supported - Single Phase (Brushed, Voice Coil, Inductive Load) Hardware Protection - Over Current, Over Temperature, Over Voltage, Short Circuit (Phase-Phase & Phase-Ground) Mechanical Specifications Description Units Value Agency Approvals - CE Class A (EMC), CE Class A (LVD), cUL, RoHS, UL Size (H x W x D) mm (in) 186.7 x 111.7 x 25.4 (7.4 x 4.4 x 1) Weight g (oz) 680 (24) Heatsink (Base) Temperature Range3 °C (°F) 0 - 65 (32 - 149) Storage Temperature Range °C (°F) -40 - 85 (-40 - 185) Form Factor - Stand Alone P1 Connector - 16-pin, 2.54 mm spaced, friction lock header P2 Connector - 4-contact, 11.10 mm spaced, tri-barrier terminal block Notes 1. Maximum duration of peak current is ~2 seconds. 2. Lower inductance is acceptable for bus voltages well below maximum. Use external inductance to meet requirements. 3. Additional cooling and/or heatsink may be required to achieve rated performance. ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 4. Analog Servo Drive 30A8I PIN FUNCTIONS P1 - Signal Connector Pin Name Description / Notes I/O 1 +10V 3mA OUT ±10 V @ 3 mA low power supply for customer use. Short circuit protected. Reference ground common with signal ground. O 2 SIGNAL GND SGND 3 -10V 3mA OUT O 4 +REF IN Differential Reference Input (±10 V Operating Range, ±15 V Maximum Input) I 5 -REF IN I 6 -TACH IN Negative Tachometer Input (Maximum ±60 V). Use signal ground for positive input. I 7 +TACH / GND Positive Tachometer Input and Signal Ground SGND 8 CURR MONITOR OUT Current Monitor. Analog output signal proportional to the actual current output. Scaling is 3.8 A/V by default but may be reduced to half this value by setting DIP switch SW-5 to OFF (see Hardware Settings section below). Measure relative to power ground. O 9 CURRENT REF OUT Measures the command signal to the internal current-loop. This pin has a maximum output of ±7.25 V when the drive outputs maximum peak current. Measure relative to signal ground. O 10 NC Not Connected (Reserved) - 11 INHIBIT IN TTL level (+5 V) inhibit/enable input. Leave open to enable drive. Pull to ground to inhibit drive. Inhibit turns off all power devices. I 12 +INHIBIT IN Positive Direction Inhibit (Does Not Cause A Fault Condition) I 13 -INHIBIT IN Negative Direction Inhibit (Does Not Cause A Fault Condition) I 14 FAULT OUT TTL level (+5 V) output becomes high when power devices are disabled due to at least one of the following conditions: inhibit, output short circuit, over voltage, over temperature, power-up reset. O 15 NC Not Connected (Reserved) - 16 NON-ISO GND Connected to power ground and can be used as a reference point for P1-8 and P1-9. PGND P2 - Power Connector Pin Name Description / Notes I/O 1 -MOT Negative Motor Output O 2 +MOT Positive Motor Output O 3 PWR GND Power Ground (Isolated From Signal Ground) PGND 4 HIGH VOLT DC Power Input I ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 5. Analog Servo Drive 30A8I HARDWARE SETTINGS Switch Functions Switch Description Setting On Off 1 Voltage feedback. Mode dependent (see mode selection table below). On Off 2 IR compensation. Activates or deactivates IR feedback. ON for IR compensation mode and OFF for other modes. On Off 3 Current loop proportional gain adjustment. ON by default. Decrease Increase 4 Inner (current) loop integral gain adjustment. OFF by default. Decrease Increase 5 Current scaling. When OFF, increases sensitivity of current sense thus reducing both peak and continuous current limit by 50%. The scaling of the current monitor output signal becomes ½ its ordinary value when this switch is OFF. Full-current Half-current 6 Current limit ratio. Used to set continuous-to-peak current limit ratio. Default is OFF. Cont./Peak Ratio = 25% Cont./Peak Ratio = 50% 7 Current loop integral gain. Activates or deactivates integration. OFF by default. Inactive Active 8 Outer loop integration. Activates or deactivates integration. ON, by default, for current mode and OFF for other modes. Inactive Active 9 Outer loop integral gain adjustment. It is recommended to leave this switch OFF for most applications. Decrease Increase 10 Test/Offset. Switches the function of the Test/Offset pot between an on-board command input for testing or a command offset adjustment. OFF by default. Test Offset Mode Selection Table Mode SW1 SW2 SW3 SW4 SW7 SW8 SW9 CURRENT OFF OFF ON OFF OFF ON OFF VOLTAGE ON OFF ON OFF OFF OFF OFF IR COMPENSATION ON ON ON OFF OFF OFF OFF TACHOMETER OFF OFF ON OFF OFF OFF OFF Note: SW7 should be off for most applications Potentiometer Functions Potentiometer Description Turning CW 1 Loop gain adjustment for voltage/velocity modes. Turn this pot fully CCW in current mode. Increases gain 2 Current limit. It adjusts both continuous and peak current limit while maintaining their ratio. Increases limit 3 Reference gain. Adjusts the ratio between input signal and output variables (voltage, current, or velocity). Increases gain 4 Offset / Test. Used to adjust any imbalance in the input signal or in the amplifier. Can also be used as an on-board signal source for testing purposes. Adjusts offset in negative direction Note: Potentiometers are approximately linear and have 12 active turns with 1 inactive turn on each end. ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 6. Analog Servo Drive 30A8I Through-hole Components† Location Description C72* Velocity Loop Integrator. Through-hole capacitor that can be added for more precise velocity loop tuning. See section below on Tuning with Through-hole components for more details. C73* Current Loop Integrator. Through-hole capacitor that can be added for more precise current loop tuning. See section below on Tuning with Through-hole components for more details. R28* Current Loop Proportional Gain. Through-hole resistor that can be added for more precise current loop tuning. See section below on Tuning with Through-hole components for more details. R77* Tachometer Input Scaling. Through-hole resistor that can be added to change the gain of the tachometer input. See section below on Tachometer Gain for more details. R8* IR Compensation Scaling. Through-hole resistor that can be added to configure the amplifier for IR Compensation mode. See section below on IR Compensation Notes for more details. Tuning With Through-hole Components In general, the drive will not need to be further tuned with through-hole components. However, for applications requiring more precise tuning than what is offered by the potentiometers and dipswitches, the drive can be manually modified with through-hole resistors and capacitors as denoted in the above table. By default, the through-hole locations are not populated when the drive is shipped. Before attempting to add through-hole components to the board, consult the section on loop tuning in the installation notes on the manufacturer’s website. Some general rules of thumb to follow when adding through-hole components are: • A larger resistor value will increase the proportional gain, and therefore create a faster response time. • A larger capacitor value will increase the integration time, and therefore create a slower response time. Proper tuning using the through-hole components will require careful observation of the loop response on a digital oscilloscope to find the optimal through-hole component values for the specific application. Tachometer Gain Some applications may require an increase in the gain of the tachometer input signal. This occurrence will be most common in designs where the tachometer input has a low voltage to RPM scaling ratio. The drive offers a through-hole location listed in the above table where a resistor can be added to increase the tachometer gain. Use the drive’s block diagram to determine an appropriate resistor value. IR Compensation Notes For applications that will use IR Compensation mode, a resistor can be added to the location named in the table above. The combination of the added resistor and correct dipswitch settings will configure the amplifier for IR Compensation mode. While in IR Compensation mode, the amplifier will adjust the duty cycle to compensate for changes in the output current. Consult the amplifier’s functional block diagram and the manufacturer’s website for more information. †Note: Damage done to the drive while performing these modifications will void the warranty. ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 7. Analog Servo Drive 30A8I MECHANICAL INFORMATION P1 - Signal Connector Connector Information 16-pin, 2.54 mm spaced, friction lock header Mating Connector Details Molex: P/N 22-01-3167 (connector) and P/N 08-50-0114 (insert terminals) Included with Drive Yes +10V 3mA OUT1SIGNAL GND2-10V 3mA OUT3+REF IN4-REF IN5-TACH IN6+TACH / GND7CURR MONITOR OUT8CURRENT REF OUT9NC10INHIBIT IN11+INHIBIT IN12FAULT OUT14NON-ISO GND16-INHIBIT IN13NC15 P2 - Power Connector Connector Information 4-contact, 11.10 mm spaced, tri-barrier terminal block Mating Connector Details Not applicable Included with Drive Not applicable -MOT1+MOT2PWR GND3HIGH VOLT4 ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 8. Analog Servo Drive 30A8I MOUNTING DIMENSIONS ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 9. Analog Servo Drive 30A8I PART NUMBERING INFORMATION ADVANCED Motion Controls servo drives are available in many configurations. All models listed in the selection tables of the website are readily available, standard product offerings. ADVANCED Motion Controls also has the capability to promptly develop and deliver specified products for OEMs with volume requests. Our Applications and Engineering Departments will work closely with your design team through all stages of development in order to provide the best servo drive solution for your system. Equipped with on-site manufacturing for quick- turn customs capabilities, ADVANCED Motion Controls utilizes our years of engineering and manufacturing expertise to decrease your costs and time-to-market while increasing system quality and reliability. Examples of Customized Products Integration of Drive into Motor Housing Integrate OEM Circuitry onto Drive PCB Mount OEM PCB onto Drive Without Cables Custom Control Loop Tuned to Motor Characteristics Multi-axis Configuration for Compact System Custom I/O Interface for System Compatibility Custom PCB and Baseplate for Optimized Footprint Preset Switches and Pots to Reduce User Setup RTV/Epoxy Components for High Vibration Optimized Switching Frequency OEM Specified Connectors for Instant Compatibility Ramped Velocity Command for Smooth Acceleration OEM Specified Silkscreen for Custom Appearance Remove Unused Features to Reduce OEM Cost Increased Thermal Limits for High Temp. Operation Application Specific Current and Voltage Limits Feel free to contact Applications Engineering for further information and details. Available Accessories ADVANCED Motion Controls offers a variety of accessories designed to facilitate drive integration into a servo system. Visit www.a-m-c.com to see which accessories will assist with your application design and implementation. Power Supplies Shunt Regulators Drive(s) Filter Cards To Motor All specifications in this document are subject to change without written notice. Actual product may differ from pictures provided in this document. AIPeak VoltagePeak Current8- Additional OptionsMaximum peak current rating in Amps. Peak voltage rating scaled 1:10 in Volts. Power Supply:DC Power SupplyRevisionAssigned a letter (A through Z) by manufacturer. AC:AC Power SupplyI:Optical IsolationIsolation Option30Command:Analog CommandDD:PWM Command ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By: