Basicelectronicdevicesandcircuits Jntu Model Paper{Www.Studentyogi.Com}

www.studentyogi.com www.studentyogi.com

Code No: 07A10401
Set No. 1
I B.Tech Regular Examinations, May/Jun 2008
BASIC ELECTRONIC DEVICES AND CIRCUITS
(Electrical & Electronic Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks

1. (a) Derive the expressions for acceleration, Velo city and displacement of a charged
particle placed in an electric eld E.
(b) Two parallel plates of a capacitor are separated by 4 cms. An electron is
at rest initally at the bottom plate. Voltage is applied between the plates,
which increases linearly from 0V to 8V in 0.1 m.sec. If the top plate is +ve,
determine:
i. The speed of electron in 40 n sec
ii. The distance traversed by the electron in 40 n sec. [8+8]

2. (a) What are the various applications of p-n junction dio de? Explain them.
(b) What are the speci cations of p-n junction diode? Explain how reverse satu-
ration current varies with temperature both in Si and Ge diodes.
(c) Explain about the characteristics of zener diode. [5+6+5]

3. (a) A 15-0-15 Volts (rms) ideal transformer is used with a full wave recti er circuit
with diodes having forward drop of 1 volt. The load is a resistance of 100ohm
and a capacitor of 10,000 f is used as a lter across the load resistance. Cal-
culate the dc load current and voltage.
(b) Explain the working of the Half wave recti er circuit with neat sketch of
waveforms at various points in the circuit. [8+8]

4. (a) A transistor operating in CB con guration has IC = 2.98 mA, IE = 3.00mA and
ICO=0.01 mA what current will ow in the collector circuit of this transistor
when connected in CE con guration with a base current of 30 A.
(b) The reverse saturation current in a transistor is 8 A. If the transistor common
base current gain is 0.979, calculate the collector and emitter current for 40
A base current. [8+8]

5. (a) Compare the advantages and disadvantages of biasing schemes.
(b) Calculate the quiescent current and voltage of collector to base bias arrange-
ment using the following data:
Vcc =10V, Rb=100K , Rc=2K , =50 and also specify a value of Rb so that
Vce =7V. [8+8]

6. (a) A transistor used in CB circuit has the following set of h parameters, hib=20 ,
hfb =0.98, hrb=3×10-4, hob= 0.5×10-6. Find the values of Ri, Ro, Ai and Av


Code No: 07A10401
Set No. 1
(b) Draw the small signal hybrid mo del of CE ampli er and derive the expressions
for its Ai, Av, Ri and Ro. [8+8]

7. (a) The output impedance may be calculated as the ratio of the open circuit volt-
age to the short circuit current. Using this method evaluate output resistance
with feedback Rof for a current-series feedback ampli er.

(b) Draw an emitter follower circuit diagram and nd the feedback factor and the
input resistance with feed back. [8+8]

8. (a) Prove that the frequency stability improves as d /dw increases in oscillators.
(b) Draw the FET crystal oscillator and derive the equation for frequency of os-
cillations. [8+8]


Code No: 07A10401
Set No. 2

1. (a) An electron is moving perpendicular to magnetic eld ‘B’. Derive the expres-
sion for radius ‘R’ of the trajectory and period of rotation T.
(b) Derive the expression for the electro magnetic de ection sensitivity in the case
of hte CRT. [8+8]

2. (a) How does the reverse sturation current of diode varies with temperature. Ex-
plain.
(b) Draw the energy band diagram of p-n diode for no bias, forward bias and
reverse bias and explain. [6+10]

3. (a) De ne the following terms of a half wave recti er with resistive load:
i. Ripple factor
ii. Peak inverse voltage
iii. Recti cation e ciency.
(b) A 230 V, 60Hz voltage is applied to the primary of a 5 : 1 step down, center
tapped transformer used in a full wave recti er having a load of 900 . If the
diode resistance and the secondary coil resistance together has a resistance of
100 , determine:
i. dc voltage across the load
ii. dc current owing through the load
iii. dc power delivered to the load
iv. PIV across each dio de.
v. Ripple voltage and its frequency. [6+10]

4. (a) For a small signal JFET iD = f(VGS, VDS). Obtain expressions for iD and
hence de ne gm, rd and .
(b) From the de nition of gm and rd obtain expression for .
(c) For an n-channel silicon FET with a = 3×10 4cm and ND = 1015 electrons/cm3.
Find the pinch o voltage. [5+5+6]

5. (a) Prove that stability factor = (IC 1 IC O 1 )S2
ß1 (ß2 +1) where S2 is the value of stabilizing
factor S when = 2
(b) Draw a circuit employing a sensistor compensation and explain its working.
[8+8]


Code No: 07A10401
Set No. 2
6. (a) Draw the equivalent circuit for the CE and CC con gurations sub ject to the
restriction that RL=0. Show that the input impedance of the two circuits are
identical.
. [8+8]
(b) For any single-transistor ampli er prove that i = hi
1 hr Av

7. (a) An ampli er has a gain of -100 and a distortion of 8%. What is the e ect of
introducing negative feedback with feedback factor of 0.05?
(b) Find Af for a CE stage with an un bypassed emitter resistor. [8+8]

8. (a) Draw the circuit diagram of a transistor phase-shift oscillator and discuss its
operation. Obtain an expression for its frequency of oscillation.
(b) What is the range of frequencies over which a crystal oscillator may be nor-
mally used and why? [8+8]


Code No: 07A10401
Set No. 3

1. (a) An electron is moving perpendicular to magnetic eld ‘B’. Derive the expres-
sion for radius ‘R’ of the trajectory and period of rotation T.
(b) Two parallel plates of a capacitor are separated by 4 cms. An electron is at
rest initially at the bottom plate. Voltage is applied between the plates, which
increases linearly from 0V to 8V in 0.1 m.sec. [8+8]

2. (a) Draw the basic structure of a varactor diode and explain its characteristics.
(b) Write the diode equation and discuss the e ect of temperature on diode cur-
rent. [8+8]
3. (a) Draw the block diagram of a regulated power supply and explain its operation.
(b) De ne line regulation and load regulation. Give their typical numerical values.
[8+8]
4. (a) Draw the circuit and explain the characteristics of BJT (input and output
characteristics) in C.E. con guration.
(b) Give the speci cations, parameters and typical values of a silicon NPN tran-
sistor. [8+8]
5. (a) Di erentiate bias stabilization and compensation techniques.
(b) Design a voltage divider bias network using a supply of 24V, =110 and
ICQ=4 A, VceQ=8V cho ose Ve=Vcc/8. [7+9]
6. (a) Draw the small signal hybrid model of CB ampli er and derive the expressions
for its Ai, Av, Ri and Ro.
(b) A transistor used in CE ampli er connection has the following set of h parame-
ters, hie=1K , hfe =100, hr e=5×10-4, hoe= 2×10-5 -1 Rs=15K , RL=5k .
Determine input impedance, output impedance, current gain and voltage gain.
[8+8]
7. (a) An ampli er has a gain of -100 and a distortion of 8%. What is the e ect of
introducing negative feedback with feedback factor of 0.05?
(b) Find Af for a CE stage with an un bypassed emitter resistor. [8+8]

8. (a) What is condition of unity loop gain to sustain oscillations? Prove it.
(b) Prove that the ratio of the parallel to series resonant frequencies of a crystal
is 1+1/2(C/C’). [8+8]


Code No: 07A10401
Set No. 4

1. (a) Draw the schematic diagram of a CRT and explain about the various sections
and the materials used.
(b) In a CRT, the electrons emitted are accelerated by a potential of 500V. The
length of the de ecting plates is 1.3 cm. Distance between the de ecting plates
is 0.5 cm. The distance between the centre of the de ecting plates and the
screen is 20 cm. Determine the value of electrostatic de ection sensitivity.
[8+8]

2. (a) Draw the basic structure of a varactor diode and explain its characteristics.
(b) Write the diode equation and discuss the e ect of temperature on diode cur-
rent. [8+8]

3. (a) Discuss the operation of HW reciti er with and without capacitor lter.
(b) Draw the Half wave recti er circuit using a step down Transformer with Vs
= 46 sin(100 t) and a semiconductor diode. Calculate the turns ratio of
the Transformer windings when the primary voltage of the Transformer is 230
volts. [8+8]

4. (a) Give the UJT symbol and simpli ed equivalent circuit with external resistors
included.
(b) Draw UJT emitter characteristics and mention various regions.
(c) If VE VP and VE VP , explain how UJT works for these conditions.[6+5+5]

5. (a) What is the necessity to stabilize the operating point of transistor ampli er?
(b) What is thermal runaway?
(c) For a xed bias con guration determine Ic, Rc, Rb and Vce using the following
speci cations: Vcc =12V, Vc=6V, =80, Ib = 40 A. [4+4+8]

6. (a) For a CB con guration, what is the maximum value of RL for which Ri does
not exceed 50 ? Transistor parameters are hib=21.6 , hrb = 2.9×10-4, hfb=-
0.98 and hob=0.49 A/V.

(b) Sketch the circuit of a CD ampli er. Derive the expression for the voltage
gain at low frequencies and what is the order of magnitude of the output
impedance. [8+8]

7. (a) Draw a feedback ampli er in block-diagram form. Identify each block and


Code No: 07A10401
Set No. 4
(b) An ampli er has a voltage gain of -100. The feedback ratio if 0.01. Find the
voltage gain with feedback, the output voltage of the feedback ampli er for
an input voltage of 1mv, feedback factor, and feedback voltage? [8+8]

8. (a) Prove that the frequency stability improves as d /dw increases in oscillators.
(b) Draw the FET crystal oscillator and derive the equation for frequency of os-
cillations. [8+8]

Basicelectronicdevicesandcircuits Jntu Model Paper{Www.Studentyogi.Com}

More Related Content

What's hot (13)

Similar to Basicelectronicdevicesandcircuits Jntu Model Paper{Www.Studentyogi.Com} (20)

More from guest3f9c6b (20)

Basicelectronicdevicesandcircuits Jntu Model Paper{Www.Studentyogi.Com}