Basics of electrical engineering presentation

BASIC ELECTRICAL &
ELECTRONICS ENGINEERING
(20A02101T)
PREPARED BY
P.I.D.T.BALADURAIKANNAN & S.GURUPRASAD
Associate Professor
Department Electrical & Electronics Engineering
VEMU IT

Voltage:-
It is defined as work done per unit charge.
Where V is the voltage (or) potential difference, W is the work done, Q is the
charge.
Current:-
It is defined as flow of charge per unit time.
(or)
Current is defined as the rate of flow of electrons in a conductor. It is measured
by the number of electrons that flow in unit time.
Where I is the current, Q is the charge of electrons, t is the time.

Work:-
When a force is applied to a body causing it to move, and if a displacement,
d is caused in the direction of the force, then
Work done = Force × Distance
W = F × D
If force is in Newtons and d is in meters, then work done is expressed in
Newton–meter which is called Joules.
Power:-
Power is the rate at which work is done, i.e., rate of doing work.
The unit of power is Joules/second which is also called Watt. When
the amount of power is more, it is expressed in Kilowatt, i.e., kW.

CLASSIFICATION OF NETWORK ELEMENTS:-

While discussing network theorems, laws, and electrical and electronic
circuits, one often comes across the following terms.
i) Circuit: A conducting path through which an electric current either
flows or is intended to flow is called a circuit.
ii) Electric network: A combination of various circuit elements,
connected in any manner, is called an electric network.
iii) Linear circuit: The circuit whose parameters are constant, i.e., they
do not change with application of voltage or current is called a linear circuit.

iv) Non linear circuit: The circuit whose parameters change with the application
of voltage or current is called a non linear circuit.
v) Circuit parameters: The various elements of an electric circuit are called its
parameters, like resistance, inductance, and capacitance.
vi) Bilateral circuit: A bilateral circuit is one whose properties or characteristics
are the same in either direction. E.g., transmission line.
vii) Unilateral circuit: A unilateral circuit is one whose properties or
characteristics change with the direction of its operation. E.g., diode rectifier.
viii) Active network: An active network is one which contains one or more
sources of EMF.
ix) Passive network: A passive network is one which does not contain any source
of EMF.
x) Node: A node is a junction in a circuit where two or more circuit elements are
connected together.

xi) Branch: The part of a network which lies between two junctions is called a
branch.
xii) Loop: A loop is a closed path in a network formed by a number of connected
branches.
xiii) Mesh: Any path which contains no other paths within it is called a mesh.
Thus, a loop contains meshes but a mesh does not contain a loop.
xiv) Lumped circuit: The circuits in which circuit elements can be represented
mutually independent and not interconnected.
Electrical circuit elements (R, L, C):-
Resistors, inductors, and capacitors are the three basic circuit parameters
or circuit components of any electrical network.

Resistor (or) resistance (R):-
The property of a material to restrict the flow of electrons is called resistance.
(or)
Electrical resistance is the opposition to the flow of electrons in a given
material.
(or)
Resistance is the property of a material due to which it opposes the flow of
electric current through it.
(or)
The opposition to flow of electrons is called electrical resistance (R).
(or)
Resistance may also be defined as ‘‘the property of the electric circuit which
opposes the flow of current’’.

The unit of resistance is ohm and is represented by the symbol Ω. The
resistance of a conductor depends on the following factors:
(i) It is directly proportional to its length.
(ii) It is inversely proportional to the area of cross section of the conductor.
(iii) It depends on the nature of the material.
(iv) It also depends on the temperature of the conductor.

Inductor:-
If the energy is stored in magnetic field, the element is inductor.
The unit of inductor is Henry, denoted by H and circuit symbol is shown
in figure.
The inductance of a coil is defined as the ratio of flux linkage to the
current flowing through the coil.
Where N is the number of turns, ϕ is the flux, I is the current.

Capacitor:-
If the energy is stored in an electric filed, the element is capacitor.
The unit of capacitor is Farad, denoted by F and circuit symbol is shown in
figure.
Charge on a capacitor, q α V,
q = CV

KIRCHHOFF LAWS:-
Two laws given by Gustav Robert Kirchhoff (1824–1887) are very useful in
writing network equations.
These laws are known as Kirchhoff’s current law (KCL) and Kirchhoff’s
voltage law (KVL).
The first law deals with flow of current and is popularly known as Kirchhoff’s
current law (KCL) while the second one deals with voltage drop in a closed circuit
and is known as Kirchhoff’s voltage laws (KVL).
1) Kirchhoff’s Current Law (KCL):
This law states that the algebraic sum of currents meeting at a junction or a
node in a circuit is zero.
(or)
The sum of current flowing towards a junction or a node is equal to the sum of
currents flowing out of the junction.
The current entering the junction has been taken as positive while the currents
leaving the junction have been taken as negative.

Basics of electrical engineering presentation

2) Kirchhoff’s Voltage Law (KVL):
KVL states that at any instant of time the algebraic sum of voltages in a closed
loop is zero.
(or)
The sum of the e.m.fs (rises of potential) around any closed loop of a circuit
equals the sum of the potential drops in that loop.
(or)
In any network, the algebraic sum of the voltage drops across the circuit
elements of any closed path is equal to the algebraic sum of the e.m.fs in the path.
A rise in potential can be assumed to be positive while a fall in potential can
be considered negative.

SERIES–PARALLEL CIRCUITS:-
Resistances, capacitances, and inductances are often connected in series, in
parallel, or a combination of series and parallel.
We need to calculate the division of voltage and currents in such circuits
1) Series Circuits:
When a number of resistances are connected end to end across a source of
supply, there will be only one path for the current to flow as shown in Figure.
The circuit is called a series circuit.
IReq = IR1 + IR2 + IR3 + IR4
Req = R1 + R2 + R3 + R4
Assuming Req as equal to R, R = R1 + R2 + R3 + R4

2) Parallel Circuits:
When a number of resistors are connected in such a way that both the
ends of individual resistors are connected together and two terminals are brought
out for connection to other parts of a circuit, then the resistors are called connected
in parallel as shown in Fig.
Voltage V is connected across the three resistors R1, R2, R3 connected in
parallel.
The total current drawn from the battery is I.
This current gets divided into I1, I2, I3 such that I = I1 + I2 + I3.
As voltage V is appearing across each of these three resistors, applying
Ohm’s law we write

3) Series–Parallel Circuits
Figure shows a number of resistors connected in series–parallel
combinations.
Here, two parallel branches and one resistance, all connected in series
have been shown.
To determine the equivalent resistance across the end terminals of the
entire circuit, we first calculate the equivalent resistance of parallel branches and
then put them in series along with any individual resistance already connected in
series.

SUPERPOSITION THEOREM:-
The superposition theorem states that in a linear network containing more
than one source, the current flowing in any branch is the algebraic sum of currents
that would have been produced by each source taken separately, with all the other
sources replaced by their respective internal resistances.
In case the internal resistance of a source is not provided, the voltage
sources will be short circuited and current sources will be open circuited.

REPRESENTATION OF SINUSOIDAL WAVEFORMS:-
A voltage which changes its polarity at regular intervals of time is called
an alternating voltage.
When an alternating voltage is applied in a circuit, the current flows first
in one direction and then in the opposite direction; the direction of current at any
instant depends upon the polarity of the voltage.

v = Vm sin ωt
where, v = Instantaneous value of alternating voltage
Vm = Max. value of alternating voltage
ω = Angular velocity of the coil

VALUES OF ALTERNATING VOLTAGE AND CURRENT:-
In a d.c. system, the voltage and current are constant so that there is no
problem of specifying their magnitudes.
However, an alternating voltage or current varies from instant to instant.
A natural question arises how to express the magnitude of an alternating
voltage or current.
There are three ways of expressing it, namely;
(i) Peak value
(ii) Average value or mean value
(iii) R.M.S. value or effective value

(i) Peak Value:
It is the maximum value attained by an alternating quantity.
The peak or maximum value of an alternating voltage or current is represented
by Vm or Im.
The knowledge of peak value is important in case of testing materials.
However, peak value is not used to specify the magnitude of alternating
voltage or current.
Instead, we generally use r.m.s. values to specify alternating voltages and
currents.
(ii) Average Value:
The average value of a waveform is the average of all its values over a
period of time.
(iii) RMS Value (or) Effective Value:
The effective (or) r.m.s. value of an alternating current is that steady
current which when flowing through a given resistance for a given time produces
the same amount of heat as produced by the alternating current when flowing
through the same resistance for the same time.

PHASE DIFFERENCE:-
When two alternating quantities of the same frequency have different zero
points, they are said to have a phase difference.
When an alternating voltage is applied to a circuit, an alternating current of the
same frequency flows through the circuit.
In most of practical circuits, for reasons we will discuss later, voltage and
current have different phases.
In other words, they do not pass through a particular point, say zero point, in
the same direction at the same instant.
Thus voltage may be passing through its zero point while the current has
passed or it is yet to pass through its zero point in the same direction.
We say that voltage and current have a phase difference.

PHASOR REPRESENTATION OFAN ALTERNATING QUANTITY:-
Alternating quantities have varying magnitude and direction.
So they are represented by a rotating vector.
A phasor is a vector rotating at a constant angular velocity.

ANALYSIS OF SINGLE-PHASE AC CIRCUITS CONSISTING OF RL - RC
- RLC SERIES CIRCUITS:-
The relationship of applied voltage and current in an ac circuit involving
only a resistance, an inductance, and a capacitance.
When a resistance is connected across an ac supply we call it a purely
resistive circuit.
Similarly an inductance coil connected across an ac supply is called a
purely inductive circuit and a capacitance connected across an ac supply is called a
purely capacitive circuit.

1) RL SERIES CIRCUITS:-
Let us consider a resistance element and an inductor connected in series as shown
in Fig (a). A voltage (V) of frequency (f) is applied across the whole circuit.
The voltage drop across the resistance is VR and across the inductor is VL.
Current flowing through the circuit is I.

2) RC SERIES CIRCUITS:-
Consider a circuit consisting of a resistance R and connected in series with a
capacitor C across an ac supply of frequency f as shown in Figure.

3) RLC SERIES CIRCUITS:-
Consider a circuit consisting of resistance R, inductance L, and capacitance C
connected in series with each other across an ac supply.
The circuit has been shown in Figure.

D.C. GENERATORS PRINCIPLE OF
OPERATION
 DC generator converts mechanical energy into electrical
energy. when a conductor move in a magnetic field in such a
way conductors cuts across a magnetic flux of lines and
e.m.f. produces in a generator and it is defined by faradays
law of electromagnetic induction e.m.f. causes current to
flow if the conductor circuit is closed.

First Law :
Whenever the magnetic flux linked with a circuit
changes, an e.m.f. is always induced in it.
or
Whenever a conductor cuts magnetic flux, an e.m.f. is
induced in that conductor.
Second Law :
The magnitude of the induced e.m.f. is equal to the
rate of change of flux linkages.

The following are the basic requirements to be satisfied
for generation of E.M.F
• Magnetic field :-
Permanent Magnet
(or)
Electro Magnet (practical)
• Conductor :- Copper (or) Aluminum bars placed in
slots cut around the periphery of cylindrical rotor
• Relative motion:-
By Prime Mover
Turbine
I.C Engine (Internal combustion)
1.A uniform Magnetic field (Flux)
2.A System of conductors
3.Relative motion between the magnetic field and conductors

Working Operation of Generators

Generated EMF or EMF Equation of a generator
Let  = flux/pole in Weber
Z =Total number of armature conductors
=No. of slot × No. of conductors/slot
P= No. of generator poles
A =No. of parallel paths in armature
N= Armature rotation in revolutions per minute (r. p. m)
E= e.m.f induced in any parallel path in armature
Average e.m.f generated/conductor = d  volt
dt
Now, flux cut/conductor in one revolution d  = P wb

No. of revolutions/sec=N/ 60
Time for one revolution , dt= 60 /N sec
According to Faraday’s Law of electro magnetic induction
E.M.F generated/conductor = d= PN volts
dt 60
No. of conductors (in series) in one parallel path= Z / A
E.M.F generated/path=  PN × Z Volts
60 A
Generate E.M.F, Eg= Z N × P Volts
60 A
For
i) Wave winding A = 2
ii) Lap winding A = P

D.C. Generator Characteristics
The following are the three most important
characteristics in a D.C. generator:
1. Open Circuit Characteristics (Eo/IF)
2. Internal Characteristics (E/Ia)
3. External Characteristics (V/Ia)

Open circuit characteristics of Separately Excited D.C.
Generator

Internal and External Characteristics

Characteristics of Shunt Generator

Characteristics of Series Generator

Compound Generator Characteristics

UNIT – 3
BASICS OF POWER SYSTEMS

Solar Energy System
Introduction
It is the best alternative source for power generation.
There are two ways, to generate electrical energy from
sunlight.
We can create electricity directly by
using photovoltaic (PV) cell.
The photovoltaic cell is made up of silicon. Many cells
are connected in series or parallel to make a solar
panel.

1. Solar Panels
It is the heart of the solar power plant. Solar panels consists a number of
solar cells. We have got around 35 solar cells in one panel. The energy
produced by each solar cell is very small, but combining the energy of 35
of them we have got enough energy to charge a 12 volt battery.
2. Solar Cells
It is the energy generating unit, made up of p-type and n-type silicon
semiconductor. It’s the heart of solar power plant.
3. Battery
Batteries are used to produce the power back or store the excess energy
produced during day, to be supplied during night.
4. D.C. to A.C. Converter (Inverter)
Solar panels produce direct current which is required to be converted into
alternating current to be supplied to homes or power grid.

Working of Solar Power Plant
As sunlight falls over a solar cells, a large number of photons
strike the p-type region of silicon. Electron and hole pair will
get separated after absorbing the energy of photon. The
electron travels from p-type region to n-type region due to the
action of electric field at p-n junction. So this, current starts
flowing in the circuit for individual solar cell. We combine the
current of all the solar cells of a solar panel, to get a significant
output.
Solar power plant have a large number of solar panels
connected to each other to get a large voltage output. The
electrical energy coming from the combined effort of solar
panels is stored in the Lithium ion batteries to be supplied at
night time, when there is no sunlight.

Advantages:
1.The transmission cost is zero for a stand-alone
solar system.
2.Solar electricity generation system is
environment-friendly.
3.The maintenance cost is low.
4.It is an ideal source for remote locations that
cannot link to the grid.
Disadvantages:
1.Initial expenses are high.
2.Require large area for bulk production.
3.Solar electricity generation system is weather-
dependent.
4.Solar energy storage (battery) is costly.

Wind Energy System
Wind turbines are used to convert wind energy into electrical energy.
Wind flows due to temperature changes in the atmosphere. Wind turbines
turn wind energy into kinetic energy. The rotating kinetic energy rotates
the induction generator, and that generator converts kinetic energy into
electrical energy.
Working of Wind Turbine
When the wind strikes the rotor blades, blades start rotating. The turbine
rotor is connected to a high-speed gearbox. Gearbox transforms the rotor
rotation from low speed to high speed. The high-speed shaft from the
gearbox is coupled with the rotor of the generator and hence the
electrical generator runs at a higher speed. An exciter is needed to give
the required excitation to the magnetic coil of the generator field system
so that it can generate the required electricity. The generated voltage at
output terminals of the alternator is proportional to both the speed and
field flux of the alternator.

Advantages:
1.Wind energy is an unlimited, free and clean source of
energy.
2.The operating cost is almost zero.
3.A wind electricity generating system can generate power in a
remote location.
Disadvantages:
1.It cannot produce the same amount of electricity at all time.
2.It needs a big open area.
3.It makes noise.
4.The construction process of a wind turbine is expensive.
5.It gives lower electricity output.
6.It poses threats from flying birds.

Basics of electrical engineering presentation

More Related Content

Similar to Basics of electrical engineering presentation (20)

Recently uploaded (20)

Basics of electrical engineering presentation