BE_YVAA_Spec_Engineering Guide

Model YVAA
Air-Cooled Screw Compressor Liquid Chillers
With Variable Speed Drive
Style A
150-500 Tons
525-1750 kW
2 Compressor
50 and 60 Hz
HFC-134a
FORM 201.28-EG1 (915)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
2
Nomenclature
Approvals
• ASME Boiler and Pressure Vessel Code – Section Vlll Division 1.
• AHRI Standard 550/590 and 551/591.
• UL 1995 – Heating and Cooling Equipment
• ASHRAE 15 – Safety Code for Mechanical Refrigeration
• ASHRAE Guideline 3 – Reducing Emission of Halogenated Refrigerants in Refrigeration and Air-Conditioning
Equipment and Systems
• N.E.C. – National Electrical Code
• OSHA – Occupational Safety and Health Act
YVAA 021 3 A X X 46 A A
UNIT TYPE
YORK Chiller
Air Cooled Screw
Design Series A
FRAME
SIZE
VOLTAGE CODE
-17 = 208-3-60
-28 = 230-3-60
-40 = 380-3-60
-42 = 400-3-60
-46 = 460-3-60
-50 = 380-415-3-50
-58 = 575-3-60
DEVELOPMENT LEVEL
REFRIGERANT
HFC - 134a
CONFIGURATION
Condenser Code
Evaporator Code
Compressor Code
Condenser Fan &
Sound Kit Code

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 3
Table of Contents
INTRODUCTION....................................................................................................................................................... 5
UNIT OVERVIEW...................................................................................................................................................... 6
YVAA CONTROL CENTER...................................................................................................................................... 9
ACCESSORIES AND OPTIONS*........................................................................................................................... 11
REFRIGERANT FLOW DIAGRAM......................................................................................................................... 17
APPLICATION DATA.............................................................................................................................................. 18
PHYSICAL DATA - MICROCHANNEL COIL - ENGLISH (SI)................................................................................ 24
PHYSICAL DATA - ROUND TUBE COIL .............................................................................................................. 28
EVAPORATOR OPTIONS....................................................................................................................................... 30
DIMENSIONS.......................................................................................................................................................... 42
RIGGING HOLE LOCATIONS................................................................................................................................ 44
ISOLATOR LOCATIONS........................................................................................................................................ 56
ISOLATORS............................................................................................................................................................ 72
ELECTRICAL DATA............................................................................................................................................... 76
POWER WIRING..................................................................................................................................................... 86
CUSTOMER CONTROL WIRING........................................................................................................................... 88
CONTROL WIRING................................................................................................................................................ 90
GUIDE SPECIFICATIONS...................................................................................................................................... 92
SI METRIC CONVERSION................................................................................................................................... 102

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
4
THIS PAGE INTENTIONALLY LEFT BLANK.

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 5
For over 140 years, Johnson Controls has raised the bar of chiller design and customer ex-
pectations. We are raising the bar again with a leap forward in air-cooled chiller technology.
Continuing the history of innovation in both compressor design and Variable Speed Drive
(VSD) technology, Johnson Controls proudly introduces the YORK® YVAA.
In the past, the choice to use an air-cooled chiller came with the expectation of compromise,
where simplicity of design and maintenance were traded for performance and efficiency.
The new YVAA provides a better balance by combining the best of both - a high perfor-
mance design that minimizes the total cost of ownership.
YORK YVAA model air-cooled chillers provide superior performance. Higher efficiency heat
exchangers coupled with variable speed operation and smart controls elevate the system
efficiency to a whole new level. The resulting benefit from YVAA chillers is much greater
than the sum of its parts.
Efficiency: Reduce your consumption
YVAA chillers are Johnson Controls’ most efficient air-cooled chillers. The design offers a
lighter, smaller and quieter package that minimizes the installed cost and maximizes usable
building space. YVAA chillers are simpler in design with easy access to service components
for reliable operation and efficient maintenance. With up to a 40% improvement in real world
efficiency versus current products, YVAA sets the new standards for lowering energy use.
Sustainability: Improve your environmental footprint
YVAA lowers both direct and indirect impact on the environment. It uses R134a refrigerant
which has zero ozone depletion potential (ODP). The design minimizes the quantity of re-
frigerant used in the system. Every YVAA model helps LEED projects earn the Energy and
Atmosphere Credit 4. The highest portion of green house gases is carbon dioxide gener-
ated from electric power plants. HVAC systems are one of the largest consumers of electric-
ity in commercial buildings. YVAA chillers reduce the electricity usage, thereby contributing
to reducing greenhouse gases and helping keep the planet cool.
Low Sound: Quiet operation makes you a good neighbor
The variable speed technology on YVAA allows unparalleled low sound levels at off peak
design conditions. This makes YVAA a great solution for sound sensitive zones. Several
acoustic attenuation options such as smart controls (SilentNight™), aerodynamic fans, and
effective sound enclosures allow the chiller to meet even the most stringent sound level
requirements.
Confidence: Proven performance provides peace of mind
YVAA design is proven by years of success with the previous generation of YORK VSD
air-cooled screw chillers with thousands of machines operating in more than one hundred
countries.
YVAA is configurable to be the perfect fit for your unique needs. YVAA offers an array
of options that can be tailored and tuned to match the capacity, efficiency, sound and
footprint for your specific application. Several variations of condenser fans, evaporator
arrangements, sound kits, protection enclosures, and controls schemes are available to
meet specific requirements for your site.
Introduction
YVAA chillers are
Johnson Controls’
most efficient air-
cooled chillers.
The design offers a
lighter, smaller and
quieter package
that minimizes the
installed costs

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
6
Unit Overview
SEMI-HERMETIC YORK TWIN SCREW COMPRESSORS
The direct-drive, semi-hermetic rotary twin-screw compressors incorporate advanced
technology in a rugged design. The continuous function, microprocessor controlled VSD
provides smooth capacity control from 100% down to 10% of chiller capacity. State-of-
the-art technology, obtained from decades of screw compressor design and manufactur-
ing by FRICK®
, ensures optimal efficiencies at all chiller load points. With no unloading
steps or slide valves in the compressors, the YVAA variable speed driven compressors
have 50% fewer moving parts than fixed speed compressors with slide valves. The YVAA
compressor is one of the most efficient and reliable screw compressors in the industry.
EVAPORATOR
The evaporator is a shell and tube, hybrid falling film type heat exchanger. It contains a
balance of flooded and falling film technology to optimize efficiency, minimize refrigerant
charge, and maintain reliable control. A specifically designed distribution system provides
uniform refrigerant flow for optimum performance.
CONDENSER
The YVAA introduces the microchannel coil to the YORK screw compressor chiller line.
Microchannel coils are made of a single material to avoid galvanic corrosion due to dis-
similar metals. Coils and headers are brazed as one piece, minimizing leaks. The inher-
ently rugged coil construction, which includes non-overhanging fins, eliminates the pos-
sibility of fin damage. The microchannel maximizes condenser heat transfer, resulting in
a smaller footprint, and reduces refrigerant charge by as much as 50%.
The condenser fans are composed of corrosion resistant aluminum hub and glass-fiber-
reinforced polypropylene composite blades molded into a low-noise airfoil section. All
blades are statically and dynamically balanced for vibration-free operation. Fan motors
are Totally Enclosed Air-Over (TEAO), squirrel-cage type and current protected. The di-
rect drive motors feature double-sealed and permanently lubricated ball bearings, cutting
down on maintenance cost over the life of the unit.
REFRIGERANT CIRCUIT
The YVAA has one independent refrigerant circuit per compressor. Each circuit uses
copper refrigerant pipe formed on computer-controlled bending machines. By using com-
puter-aided technology, over 60% of system piping brazed joints have been eliminated
(as compared to designs that use fittings), resulting in a highly reliable and leak-resistant
system.
COMPLETE FACTORY PACKAGE
Each unit is shipped as a complete factory package, completely assembled with all in-
terconnecting refrigerant piping and internal wiring and ready for field installation. Prior
to shipment, each individual chiller undergoes an extensive testing procedure, ensuring
workmanship is the highest quality and that the initial start-up is trouble-free.

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 7
Before leaving the factory, each refrigerant circuit is factory pressure tested, evacuated
and then fully charged with R134a refrigerant and oil. An operational test is performed
with water flowing through the evaporator to ensure each circuit functions correctly.
ELECTRICAL
All controls and motor starting equipment necessary for unit operation are factory wired
and function tested. There are no surprises when you go to start-up; you can have confi-
dence that the unit will start up right the first time and every time.
The chillers are available with a single point power connection and are supplied with a
factory mounted and wired control transformer that powers all unit controls from the main
unit power supply. The transformer utilizes scheduled line voltage on the primary side and
provides 115V/1Ø on secondary. The standard unit is equipped with terminal block elec-
trical connections. All exposed power wiring is routed through liquid-tight, UV-stabilized,
non-metallic conduit. Selection of frame 36 and larger are standard dual point, with single
point option.
VSD Power/Control Panel includes main power connection(s), VSD and fan motor con-
tactors, current overloads, and factory wiring. All display and control features can be ac-
cessed through the keypad and control display access door, eliminating the need to open
the main cabinet doors.
BUILDING AUTOMATION SYSTEM CAPABILITIES
The E-Link Gateway provides an economical and versatile connection between Johnson
Controls equipment and open/standard protocols. It efficiently manages the communica-
tion protocols currently used by Johnson Controls equipment, exposing the data in a con-
sistent, organized, and defined fashion. A simple switch selection allows configuration of
the required equipment profile and output protocol, which reduces equipment connectivity
startup time.
Johnson Controls systems or another vendor’s systems can incorporate these setpoints
and data outputs to give the customer a complete understanding of how the system is
running through a Building Automation System.
During extreme or unusual conditions (i.e. blocked condenser coils, ambient above sched-
uled maximum, etc.) the chiller control system will avoid shutdown by varying capacity. By
monitoring motor current and suction and discharge pressures, the chiller can maintain
maximum available cooling output without shutting down.
Unit Safeties are provided for the chiller to perform auto-reset shut down for the following
conditions:
• Ambient temperature above or below allowable range
• Out of range leaving chilled liquid temperature
• Under voltage
• Flow switch operation
Unit Overview (Cont'd)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
8
AHRI CERTIFICATION PROGRAM
YORK YVAA chillers have been tested and certified by Air-Conditioning, Heating and Re-
frigeration Institute (AHRI) in accordance with the latest edition of AHRI Standard 550/590
(I-P). Under this Certification Program, chillers are regularly tested in strict compliance
with this Standard. This provides an independent, third-party verification of chiller perfor-
mance. Refer to the AHRI site at: www.ahrinet.org/ for complete Program Scope, Inclu-
sions, and Exclusions as some options listed herein fall outside the scope of the AHRI
certification program. For verification of certification, go to the AHRI Directory at www.
ahridirectory.org.
Rated in accordance with the latest
issuance of AHRI Standard 550/590
and 551/591.
COMPUTERIZED PERFORMANCE RATINGS
Each chiller is custom-matched to meet the individual building load and energy require-
ments. A variety of standard heat exchangers and pass arrangements are available to
provide the best possible match.
It is not practical to provide tabulated performance for each combination, as the energy
requirements at both full and part load vary significantly with each heat exchanger and
pass arrangement. Computerized ratings are available through each Johnson Controls
sales office. Each rating can be tailored to specific job requirements, and is part of the
AHRI Certification Program.
OFF-DESIGN PERFORMANCE
Since the vast majority of its operating hours are spent at off-design conditions, a chiller
should be chosen not only to meet the full load design, but also for its ability to perform
efficiently at lower loads. It is not uncommon for chillers with the same full load efficiency
to have an operating cost difference of over 10% due to differences in off-design (part-
load) efficiencies.
Part load information can be easily and accurately generated by use of the computer. And
because it is so important to an owner’s operating budget, this information has now been
standardized within the AHRI Certification Program in the form of an Integrated Part Load
Value (IPLV), and Non-Standard Part Load Value (NPLV).
The current IPLV/NPLV rating from AHRI Standard 550/590 and 551/591 much more
closely tracks actual chiller operation, and provides a more accurate indication of chiller
performance than the previous IPLV/APLV rating. A more detailed analysis must take into
account actual building load profiles, and local weather data. Part load performance data
should be obtained for each job using its own design criteria.
Unit Overview (Cont'd)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 9
UNIT CONTROL CENTER
The unit control center provides automatic control of chiller operation including compres-
sor start/ stop and load/unload anti-recycle timers, condenser fans, chilled liquid pump,
evaporator heater, unit alarm contacts and run signal contacts. The microcomputer control
center comes online as soon as the main power switch on the unit is switched on; imme-
diately, the microcomputer control center will begin to continuously monitor all variables.
Figure 1 - VIEW OF YORK CONTROL CENTER KEYPAD AND DISPLAY
The microprocessor controls the unit’s capacity by matching the actual leaving chilled
liquid temperature (LCHLT) to the user-defined setpoint. Factors that may cause the
system’s actual LCHLT to fluctuate are changes in ambient temperature, load, and chilled
liquid loop flow rate and volume. The controls system reacts to such changes by adjust-
ing the number of compressors that are on and the loading of each compressor in order
to keep the LCHLT at the setpoint.
The controls system logic monitors the rate at which the LCWT is approaching the set-
point to ramp up or down compressor capacity as required. The variable frequency drive
allows the compressor capacity to match the load.
Display Data
• Leaving Chilled Liquid Temperature
• Returning Liquid Temperature
• Ambient Temperature
• Lead System
• Compressor Capacity (% of Full Load Amps)
• VSD Output Frequency / Compressor Speed
• Compressor Run Hours
• Compressor Number of Starts
• Oil Pressure and Temperature (per Compressor)
YVAA Control Center

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
10
• Chilled Liquid Pump Status
• Evaporator Heater Status
• History Data for Last Twenty Normal Shutdowns
• History Data for Last Ten Shutdown Faults
Programmable Setpoints
• Chiller on/Off
• Chilled Liquid (Water or Glycol)
• Local or Remote Control
• Units of Measure (Imperial or SI)
• System Lead/Lag
• Remote Temperature Reset
• Remote Current Limit
• Leaving Chilled Liquid Temperature Setpoint and Range
YVAA Control Center (Cont'd)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 11
SOUND ATTENUATION
Low Noise Kits – The standard chiller configuration is equipped with low sound fans.
There are several sound attenuation options available to further reduce sound at its
source thereby meeting local sound level regulations.
SilentNight™ - Due to time-of-day based sound regulations in some locations, it may be
desirable to force the chiller to a lower sound level on demand. The SilentNight control
option provides a control input to limit sound output of the chiller based on time of day.
This feature is programmable at the chiller panel or can be controlled remotely via a signal
(4-20mA or 0-10 VDC) from a BAS system.
Ultra Quiet Fans – The chiller is equipped with specially designed fans and motors to pro-
vide lower sound levels yet retain appropriate airflow. The result is reduced fan generated
sound with minimal effect on the chiller capacity or efficiency at standard AHRI conditions.
The fans are three-bladed for 60Hz and five-bladed for 50Hz.
FAN OPTIONS
High Static Fans - (380V/60 Hz, 460V/60 Hz, 400V/50 Hz) The chiller is equipped with
condenser fans with higher power motors suitable for high external static pressure, up to
100Pa (0.4 in. water), across condenser coils. This option should be selected if additional
airflow resistance may be present due to flow restrictions such as field installed ducts,
filters, sound enclosures etc. Please contact your local Johnson Controls representative
for more information.
High Airflow Fans - (380V/60 Hz, 460V/60 Hz, and 400V/50 Hz) The chiller is equipped
with condenser fans with airfoil-type polycarbonate blades and high power motors provid-
ing extra airflow across coils. In some chiller configurations, this option can provide an
increase in chiller capacity at high ambient. Please contact your local Johnson Controls
representative for more information.
CONDENSER
Coils – Fin and tube condenser coils of seamless, internally-enhanced, high-condensing-
coefficient, corrosion resistant copper tubes are arranged in staggered rows. The tubes
are mechanically expanded into aluminum fins. Integral subcooling is included. The de-
sign working pressure of the coils is 350 PSIG (24 barg).
CONDENSER COIL PROTECTION
The aluminum alloys used in the YVAA microchannel condenser have been carefully se-
lected and tested for high corrosion resistance. However, all metals can corrode in harsh
conditions. Consider protecting coils from corrosive environments such as coastal, ma-
rine, urban and industrial.
Post-Coated Epoxy Dipped Condenser – Microchannel condenser coils applied with
electro-deposited and baked flexible epoxy coating that is finished with a polyurethane UV
resistant top-coat suitable for highly corrosive applications.
Accessories and Options*
*All options factory mounted unless otherwise noted.

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
12
PROTECTIVE CHILLER PANELS
Wire Panels – UV stabilized black vinyl coated, heavy gauge, welded wire mesh guards
mounted on the exterior of the full unit. Protects condenser coil faces and prevents un-
authorized access to refrigerant components (compressors, pipes, evaporator, etc.), yet
provides free air flow. This can cut installation cost by eliminating the need for separate,
expensive fencing. See Figure 2.
Figure 2 - FULL UNIT WIRE PANELS
Louvered Panels – Louvered panels, painted the same color as the unit, enclose the unit
to visually screen and protect the coils as well as prevent unauthorized access to internal
components. Also available as a condenser-only option. See Figures 3.
Figure 3 - FULL UNIT LOUVERED PANELS
Accessories and Options (Cont'd)
LD18593
LD18594

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 13
Louvered/Wire Panels Combination - Louvered panels, painted the same color as the
unit, are mounted on external condenser coil faces. Heavy gauge, welded wire-mesh
panels, coated to resist corrosion, are mounted around base of machine to restrict unau-
thorized access. See Figure 4.
Figure 4 - LOUVERED/WIRE PANELS COMBINATION
END HAIL GUARD – Louvered panels, painted the same color as the unit, are installed
on the rear of the unit (opposite end of the control panel) to protect the exposed con-
denser from flying debris or hail. See Figure 5.
Figure 5 - END HAIL GUARD
LD18595
LD18596

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
14
V-GUARD PANELS – Solid panels, painted the same color as the unit, are installed along
the sides of the units to cover exposed piping within the condenser section without impact-
ing airflow. These guard panels can be combined with End Hail Guard option for additional
protection from debris. See Figure 6.
Figure 6 - V-GUARD OPTION
EVAPORATOR OPTIONS
1-1/2” Insulation – Double thickness insulation provided.
Flange Kit – Provides contractor with the couplings best suited to tie into the chilled liquid
piping. All flanges are ANSI 150 psig (10.3 barg). Field mounted. Options include:
• ANSI/AWWA C-606 Flanges - 2 flanges, for applications where field piping has ex-
isting flanges.
• ANSI/AWWA C-606 Flanges - 4 flanges, for applications where customer wants
flanged connections which do not exist on the field piping.
• Weld Flanges - 2 flanges, for customer to weld to evaporator to mate to existing
flanges on field piping.
• Weld Flanges - 4 flanges, for customer to weld to evaporator and customer wants
flanged connections which do not exist on the field piping
Connection Location - The standard unit configuration is available with liquid inlet con-
nections at rear (opposite control panel end) of unit. Option available for front fluid inlet on
select configurations.
Three-Pass – The standard evaporator is constructed with two chilled water passes
through the evaporator. The three-pass option is recommended for use in brine applica-
tions or where a greater water temperature difference is required but efficiency cannot be
sacrificed.
Single Pass – The single pass evaporator option offers the lowest water pressure drop
and is recommended for high flow or series chiller applications.
300 PSIG Cooler – Standard cooler is rated 150 psig; 300 PSIG is available for applica-
tions such as high rise buildings.
LD18597

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 15
Water Box Heater - The standard unit comes with freeze protection on the evaporator
down to 0°F (-17.8°C) Unless the appropriate concentration of glycol is used, optional
water box heaters are required for storage below 0°F (-17.8°C). See Application Data
section for additional information on freeze protection. Separate 120V single phase power
supply required.
CONTROLS OPTIONS
Building Automation System Interface (Temperature) - Factory installed option to ac-
cept a 4 to 20 mA or a 0 to 10 VDC input to allow remote reset of the Leaving Chilled
Liquid Temperature Setpoint. The setpoint can be positively offset upwards up to 40°F
(22.2°C). This option is useful for ice storage or process applications or for periods where
higher chilled liquid temperatures are adequate for low loads. Available alone or in com-
bination with BAS Load Limit.
Building Automation System Interface (Load Limit) - Factory installed option to accept
a 4 to 20 mA or a 0 to 10 VDC input to allow remote reset of the Load Limit Setpoint. The
setpoint can limit system demand from 30-100%. Available alone or in combination with
BAS Temperature Reset.
E-Link – The E-Link gateway provides full communication to Building Automation Sys-
tems, including BACnet (MS/TP), Modbus, LON and N2.
Thermal Storage – Provides special control logic and modifications to produce leaving
chilled brine temperatures below 40°F (4.4°C) primarily at times of low ambient tempera-
tures (night time). Option can be used to produce ice to supplement cooling and signifi-
cantly decrease energy costs. The capability of the chiller is enhanced by using both ice
and chilled liquid simultaneously during times of peak cooling needs.
GENERAL OPTIONS
Flow Switch Accessory - Vapor proof SPDT, NEMA 3R switch, 150 psig (10.3 barg)
DWP, -20°F to 250°F (-29°C to 121°C) with 1” NPT (IPS) connection for upright mounting
in horizontal pipe (This flow switch or equivalent must be furnished with each unit). Field
mounted.
Differential Pressure Switch – This 3-45 psig (0.2-3 barg) range switch, with 1/4” NPTE
pressure connections, is an alternative to the paddle-type flow switch. Field mounted.
Service Isolation Valve – Service suction isolation valve added to the unit for each refrig-
erant circuit. Valve is available in both manual and chiller actuated configurations. Actuat-
ed valve is recommended for operation below freezing ambients with water in evaporator
(refer to “OPERATION IN SUB FREEZING CONDITIONS” of Application Data section).
Chicago Code Relief Valve - Special relief valves per Chicago code.
Dual Pressure Relief Valve – Two safety relief valves are mounted in parallel; one is
always operational to assist in valve replacement during maintenance.
Pressure Vessel Options – The evaporator can be provided with either ASME or PED
pressure vessel codes certification.
Circuit Breaker – Unit-mounted circuit breaker(s) with external lockable handle(s) will be
supplied to isolate the power voltage for servicing. The circuit breaker(s) is (are) sized to
provide motor branch circuit protection, short circuit protection and ground fault protection
for the motor branch-circuit conductors, the motor control apparatus and the motors.

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
16
Non-Fused Disconnect Switch – Unit-mounted disconnect switch(es) with external lock-
able handle can be supplied to isolate the unit power voltage for servicing. Separate
external fusing must be supplied by the power wiring, which must comply with local codes.
Special Requirement Documents – There are two options to select from:
• Special Requirement Document Package (SRDP) includes Pressure Vessel Report,
Unit Run Test Report, Production System Check Sheet and Final Unit Inspection
Check Sheet.
• Materials Package includes steel mill material reports for vessels in addition to the
SRDP.
VIBRATION ISOLATION
Elastomeric Isolation – This option is recommended for normal installations. It provides
very good performance in most applications for the least cost. Field mounted.
1” Spring Isolators – Spring and cage type isolators for mounting under the unit base
rails are available to support unit. They are level adjustable. 1” nominal deflection may
vary slightly by application. Field mounted.
2” Restrained Spring Isolators – Restrained Spring-Flex Mounting isolators incorporate
a rugged welded steel housing with vertical and horizontal limit stops. Housings designed
to withstand a minimum 1.0g accelerated force in all directions up to 2” (51mm). The de-
flection may vary slightly by application. They are level adjustable. Field mounted.

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 17
Low pressure refrigerant (liquid and gas) enters the evaporator and is sprayed across the
top of the tube bundle from spray nozzles. The liquid refrigerant from the nozzles grav-
ity drains down across the tube bundle and is evaporated and superheated by the heat
energy absorbed from the chilled liquid passing through the tubes.
The low pressure refrigerant vapor leaves the top of the evaporator and enters the com-
pressor where the refrigerant vapor is compressed and the pressure and superheat are
increased. The high pressure superheated gas enters the air cooled condenser where
heat is rejected via the condenser coils and fans.
The fully condensed and sub-cooled liquid leaves the air cooled condenser, flows through
the filter drier and enters the economizer tank. The flow of refrigerant into the economizer
is controlled by the electronic expansion valve.
Additional cooling of the refrigerant liquid may take place in the economizer tank when
the economizer valve is opened. After leaving the economizer tank, liquid refrigerant
flows through an orifice where pressure reduction and further cooling take place. The low
pressure refrigerant (liquid and gas) then enters the evaporator.
Refrigerant Flow Diagram
SYMBOL YVAA SYSTEM COMPONENT
Electronic Expansion Valve
Ball Valve
Relief Valve
Stop Valve Angle, Access
Replacement Core Filter/Dryer
Sight Glass
Orifice
Check Valve
Valve
LD18592

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
18
Application Data
UNIT SIZING
Avoid over-sizing a chiller. Properly sized chillers operate stably and provide the best
life cycle cost. When designing phased projects, select multiple small chillers to match
demand for each phase. Use multiple small chillers when the minimum cooling demand
is less than 10% of the maximum cooling demand.
UNIT LOCATION
The YVAA chillers are designed for outdoor installation. To achieve optimum performance
and trouble-free service provide adequate space around chillers (see Figure 7).
1.8m) MINIMUM
1.8m)
MINIMUM
3m)
MINIMUM
1.2m) MINIMUM
Figure 7 - ACCEPTABLE MINIMUM CLEARANCES AROUND/BETWEEN UNIT(S)
FOR PROPER AIRFLOW
When selecting chiller installation sites, follow these requirements:
A. Installation sites may be either on a roof or on ground level. (See FOUNDATION on
Page 19)
B. Provide space for air to flow into condensers per dimensions shown on the dimension
drawing on pgs 20 and 21. Restricted airflow or hot air recirculation will diminish per-
formance. Johnson Controls’ unit controls will optimize the operation without nuisance
high pressure safety cutouts; however, the system designer MUST consider potential
performance degradation. Recommended clearances for all units are as follows:
1. Access to the unit control center stipulates the unit is no higher than on spring isola-
tors.
LD18633

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 19
2. Recommended minimum clearances:
a. Side to wall – 6’ (1.8m)
b. Rear to wall – 6’ (1.8m)
c. Control panel end to wall – 4’ (1.2m)
d. Top – no obstructions whatsoever
e. Distance between adjacent units – 10’ (3m)
3. No more than one wall around the chiller yard should be higher than the chiller(s)
C. Avoid locations near windows or structures where normal operating sounds may be
objectionable.
D. The condenser fans are propeller-type and are not recommended for use with duct-
work, filters or other impediments to airflow in the condenser air stream.
E. When obstructions to airflow exist, they must not add more than 0.1” external static
pressure.
F. Protection against corrosive environments is available by ordering the units with cured
epoxy-coating on the condenser microchannel. Epoxy-coated coils should be used
with any units being installed at the seashore, or where salt spray may hit the units, or
where acid rain is prevalent.
G. On installations where winter operation is intended and snow accumulations are ex-
pected, additional elevation must be provided to insure normal condenser air flow.
H. Provide adequate space for tubes to be removed from evaporator. For clearances
please contact your nearest Johnson Controls Sales Office.
FOUNDATION
Mount units on a flat and level foundation, ground or roof, capable of supporting the entire
operating weight of the equipment. Please contact your nearest Johnson Controls Sales
Office for shipping and operating weights.
Roof Locations – Provide structure to safely support the entire weight of the unit and ser-
vice personnel. Do not damage the roof during installation. If the roof is “bonded”, consult
a building contractor or architect for special installation requirements. Use spring isolators
to minimize vibration transmission into building structure. Provide additional structural
support at the spring-isolator locations.
Ground Locations – Units must be installed on a substantial base that will not settle and
cause strain on the refrigerant lines, resulting in possible leaks. A one-piece concrete slab,
with footers extending below the frost line is recommended. The slab should not be tied
to the main building foundation as operational noise will telegraph. Mounting holes (5/8”)
are provided in the base rails for bolting the unit to its foundation. See Isolator Locations
on Page 56 for location of the mounting holes.
For ground installations, precautions should be taken to protect the unit from tampering
by, or injury to, unauthorized persons. Fasteners on access panels will prevent casual
tampering; however, further safety precautions such as unit enclosure options, a fenced-
in enclosure, or locking devices on the panels may be advisable. Check local authorities
for safety regulations.
Application Data (Cont'd)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
20
Seismic Applications – Avoid installing chillers on springs or roofs where earthquakes
are a risk. Springs and roofs amplify earthquake forces. Rigidly mounting chillers to
ground level concrete pads is typically the best option for earthquake zones. Contact
Johnson Controls equipment specialists for help with projects that have seismic require-
ments.
CHILLED LIQUID PIPING
Design the chilled liquid piping system so that the circulating pump discharges into the
evaporator. The inlet and outlet evaporator-liquid connections are given in Dimensions on
Page 42. Hand stop valves are recommended in all lines to facilitate servicing. Provide
drain connections at low points to permit complete drainage of the evaporator and system
piping.
The evaporator must be protected by a strainer, preferably of 40 mesh, fitted as close as
possible to the liquid inlet connection, and provided with a means of local isolation.
The evaporator must not be exposed to flushing velocities or debris released during flush-
ing. It is recommended that a suitably sized bypass and valve arrangement is installed
to allow flushing of the piping system. The bypass can be used during maintenance to
isolate the heat exchanger without disrupting flow to other units.
Pressure-gauge connections are recommended for installation in the inlet and outlet liquid
lines. Gauges are not provided with the unit and are to be furnished by others.
A flow switch is available as an accessory on all units. A flow switch must be installed in
the leaving liquid piping of the evaporator and must not be used to start and stop the unit.
Chilled liquid lines exposed to the weather should be wrapped with a supplemental heater
cable and insulated, or glycol should be added to the chilled liquid to protect against freez-
ing if low-ambient periods are expected.
OPERATION IN SUB-FREEZING CONDITIONS
The YVAA may be operated in sub-freezing conditions if the following freeze protections
are taken :
A. An automatic suction service valve electric actuator is installed. Chiller software will
operate the actuator in order to protect against freezing due to evaporator refrigerant
migration.
-or-
B. No suction service valve is installed but the water circuit valves are kept open, there is
continuous power to the chiller and pump for chilled water pump control, and the pump
will operate and circulate water through the evaporator whenever commanded by the
chiller.
Warning: The above operation is only advised if uninterrupted power can be ensured.
Unforeseen power interruptions can damage the evaporator in a very short time frame if
the temperature falls below freezing.
If there is potential for power loss, Johnson Controls recommends the water in the chilled
water circuit be replaced with an appropriate water-to-glycol concentration.

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 21
UNIT MAINTENANCE AND SHUTDOWN IN SUB-FREEZING CONDITIONS
If the YVAA is maintained or shut down and will be subjected to sub-freezing conditions,
it is critical to protect against evaporator and waterbox freeze damage. Johnson Controls
recommends the following options (in order of freeze protection level) be performed on
each circuit.
A. Glycol: Replace water with an appropriate water to glycol concentration of antifreeze.
-or-
B. Drain: Remove power to the waterbox heaters. Close the water valves, drain the evap-
orator, and leave the evaporator drain valves open.
-or-
C. Refrigerant Valve - Off: Close the water valves, close flash tank drain valves, close
the suction service valves and leave power to the chiller for evaporator heater mat
and waterbox heater operation. For units without a suction service valve, close the
discharge and compressor oil valves.
-or-
D. Pump Control: Keep power to the chiller in order to have control over chilled water
pumps and heater operation and leave the water circuit valves open. This will enable
water to circulate through the evaporator to avoid freezing.
Warning: Options A and B are the recommended processes for unit maintenance and
shutdown. Unforeseen power interruptions can damage the evaporator in a very short
time frame if the temperature falls below freezing.
Note: Failure to follow Johnson Controls freeze protection recommendations can void the
warranty.
MINIMUM LIQUID VOLUME
It is good practice to include as much liquid volume as possible in a chilled liquid loop.
This increases the thermal mass and “Flywheel” effect within the system (i.e. the more the
better) which in turn promotes stable liquid temperature control and increases reliability
by reducing compressor cycling.
For air conditioning applications, a minimum of 3 gallons/ton (3.2 liters/cooling KW) is rec-
ommended. It is preferred that the gallon/ton ratio be within the 5 to 8 (5.4 to 8.6 liter/cool-
ing KW) range for constant flow rate chilled liquid systems. See "VARIABLE PRIMARY
FLOW" on page 23 for recommendations for VPF systems. For process applications,
a minimum of 6 gallons/ton (6.5 liter/cooling KW) ratio is recommended with preference
towards a range of 7 to 11 (7.5 to 11.8). Install a tank or increase pipe sizes to provide
sufficient liquid volume.
LEAVING LIQUID TEMPERATURE OUT OF RANGE
The YVAA chiller line has a maximum leaving liquid temperature of 60°F (15.6°F). Some
process applications require a chilled liquid temperature higher than what the chiller pro-
vides. In those applications, a simple piping change can remove the problem. By using a
mixture of chiller-cooled liquid and returning process liquid, the chilled liquid entering the
process can be held at the desired temperature. (A tank can also be used to meet high
leaving liquid temperature requirements.) (See Leaving Liquid temperature out of range
suggested layout on Page 22)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
22
FLOW RATE OUT OF RANGE
Each YVAA evaporator has a minimum and maximum flow rate. Some process applica-
tions require a flow rate that is out of range for the evaporator. In those applications, a
piping change can remove the problem.
In applications where the required flow rate is less than the evaporator’s minimum al-
lowable, the chilled liquid can be recirculated to the chiller. (See Suggested layout for
applications with a flow rate greater than the evaporator maximum allowable flow rate on
Page 22)
Figure 8 - LEAVING LIQUID TEMPERATURE OUT OF RANGE SUGGESTED
LAYOUT
Figure 9 - SUGGESTED LAYOUT FOR APPLICATIONS WITH A FLOW RATE
GREATER THAN THE EVAPORATOR MAXIMUM ALLOWABLE FLOW RATE

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 23
In applications where the required flow rate is greater than the evaporator’s maximum
allowable, the chilled liquid can be recirculated to the load (see Figure 10 on page 23).
THERMAL STORAGE
Thermal storage is the practice of storing cooling energy during a period of little or no load
and/or low energy costs for use during periods of high load and/or energy costs. Conven-
tional cooling systems produce cooling when it is needed which is commonly during times
of peak demand. Thermal storage allows generation of cooling capacity to occur during
off-peak periods and store that capacity to meet future cooling requirements. Using ther-
mal storage can result in smaller equipment sizes, thereby reducing capital cost, and also
can result in significant energy cost savings.
Figure 10 - SUGGESTED LAYOUT FOR APPLICATIONS WITH A FLOW RATE LESS
THAN THE EVAPORATOR MINIMUM ALLOWABLE FLOW RATE
The YVAA has special control logic to be able to produce chilled leaving brine tempera-
tures below 40°F (4.4°C) so as to supply a storage tank with chilled liquid during times of
low demand. YVAA chillers selected for thermal storage operation can also be selected
to efficiently provide chilled liquid at nominal cooling loads.
VARIABLE PRIMARY FLOW
Johnson Controls recommends a maximum 10% per minute flow rate of change, based
on design flow, for variable primary flow applications. Eight to 10 gallons per chiller ton
(8.6 to 10.8 liter per cooling KW) is recommended for the system liquid volume . Insuf-
ficient system volume and rapid flow changes can cause control problems or can even
cause chiller shutdowns. There are many other design issues to evaluate with variable
primary flow systems. Consult your Johnson Controls Sales Office for more information
about successfully applying YVAA chillers.

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
24
The data shown in this table is applicable to selected typical configurations. Other configurations are available
through our configuration/selection software. Please contact your nearest Johnson Controls Sales Office for the
chiller configuration that best matches your specific needs.
Physical Data - Microchannel Coil - English (SI)
NOTES:
1. Shipping and operating weights shown are for base unit; selected options may add weight to unit. Contact your nearest Johnson Controls
Sales office for weight data.
2. For leaving liquid temperature below 40°F(4.4°C) or above 70°F (21.1°C), contact your nearest Johnson Controls Sales Office for applica-
tion requirements.
UNIT FRAME 15 16 17 18 19 19 20 21 21
CONDENSER CODE 3 5 8 3 5 8 0 3 5
EVAPORATOR CODE B B C A A B C A C
GENERAL UNIT DATA
Number of Independent
Refrigerant Circuits
2
Refrigerant Charge, R-134a,
Circuit.-1/Circuit.-2, lbs (kg)
175/175
(79/79)
190/190
(86/86)
225/225
(102/102)
175/155
(79/70)
190/170
(86/77)
220/195
(100/88)
205/205
(93/93)
175/175
(79/79)
225/225
(102/102)
Oil Charge, Circuit.-1/Circuit.-2,
gal (liters)
2.1/2.0
(8.0/7.7)
2.2/2.2
(8.5/8.5)
2.5/2.5
(9.3/9.3)
2.4/2.0
(9.2/7.7)
2.6/2.1
(9.7/8.0)
2.7/2.2
(10.4/8.5)
2.6/2.6
(10.0/10.0)
2.5/2.5
(9.3/9.3)
2.8/2.8
(10.5/10.5)
Minimum Load % 10%
Unit shipping weight, lbs (kg) 1
11518
(5224)
12084
(5481)
14668
(6653)
12019
(5452)
12781
(5797)
13776
(6248)
13392
(6074)
12859
(5833)
14915
(6765)
Operating Weight, lbs (kg) 1
11979
(5434)
12546
(5691)
15432
(7000)
12460
(5652)
13222
(5997)
14237
(6458)
14155
(6421)
13300
(6033)
15678
(7111)
Chassis Dimensions - Length,
inches (mm)
203.3
(5163)
247.2
(6280)
291.2
(7397)
247
(6274)
291.2
(7397)
335.2
(8514)
226
(5741)
291.2
(7397)
291.2
(7397)
Chassis Dimensions - Width,
inches (mm)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
Chassis Dimensions - Height,
inches (mm)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
COMPRESSORS, SEMI-HERMETIC SCREW
Quantity per Chiller 2
CONDENSER FANS
Number Circuit-1/Circuit-2 4/4 5/5 6/6 6/4 7/5 8/6 4/4 6/6 6/6
Air on Condenser (Min/Max),
°F (°C)
0°F/131°F
(-17.8°C/55°C)
EVAPORATOR, SHELL AND TUBE HYBRID FALLING FILM 2
Water Volume, gal (liters)
58
(220)
58
(220)
71
(269)
48
(182)
48
(182)
58
(220)
71
(269)
48
(182)
71
(269)
Leaving Water Temperature
(Min/Max), °F (°C) 2
40/70
(4.4/21.1)
Maximum Water Side Pressure,
psig (barg)
150
(10.3)
Maximum Refrigerant Side
Pressure, psig (barg)
235
(16.2)
Evaporator Drain Connection,
inches (mm)
3/4

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 25
NOTES:
tion requirements.
Physical Data - Microchannel Coil - English (SI) (Cont'd)
UNIT FRAME 21 23 24 24 26 27 27 27 29 30
CONDENSER CODE 8 3 5 8 3 3 5 8 5 3
EVAPORATOR CODE C B C C B D E E E C
GENERAL UNIT DATA
2
240/240
(109/109)
210/190
(95/86)
250/225
(113/102)
250/250
(113/113)
210/210
(95/95)
265/265
(120/120)
265/265
(120/120)
270/270
(122/122)
310/265
(141/120)
290/245
(132/111)
gal (liters)
2.9/2.9
(10.8/10.8)
2.7/2.6
(10.1/9.7)
2.9/2.8
(11.1/10.5)
2.9/2.9
(11.1/11.1)
2.7/2.7
(10.1/10.1)
3.0/3.0
(11.4/11.4)
3.0/3.0
(11.4/11.4)
3.1/3.1
(11.6/11.6)
4.2/3.1
(15.9/11.7)
4.1/3.0
(15.5/11.4)
Minimum Load % 10%
15677
(7111)
13288
(6027)
15873
(7200)
16634
(7545)
14076
(6385)
16275
(7382)
16991
(7707)
17753
(8052)
18205
(8258)
17114
(7763)
16440
(7457)
13750
(6237)
16636
(7546)
17398
(7891)
14538
(6594)
17103
(7758)
17851
(8097)
18612
(8442)
19065
(8648)
17877
(8109)
inches (mm)
335.2
(8514)
291.2
(7397)
335.2
(8514)
379.1
(9631)
335.2
(8514)
335.2
(8514)
335.2
(8514)
379.2
(9631)
379.2
(9631)
379.2
(9631)
inches (mm)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
inches (mm)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
CONDENSER FANS
Number Circuit-1/Circuit-2 7/7 7/5 8/6 8/8 7/7 7/7 7/7 8/8 9/7 9/7
°F (°C)
0°F/131°F
(-17.8°C/55°C)
71
(269)
58
(220)
71
(269)
71
(269)
58
(220)
82
(310)
113
(428)
113
(428)
113
(428)
71
(269)
40/70
(4.4/21.1)
psig (barg)
150
(10.3)
235
(16.2)
inches (mm)
3/4

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
26
NOTES:
tion requirements.
UNIT FRAME 30 30 31 32 33 34 34 36 37
CONDENSER CODE 5 8 8 3 3 3 5 8 3
EVAPORATOR CODE C E E E C E E J F
GENERAL UNIT DATA
2
295/250
(134/114)
315/275
(143/125)
315/295
(143/134)
295/295
(134/134)
290/290
(132/132)
310/310
(141/141)
315/315
(143/143)
475/320
(216/145)
420/245
(191/111)
gal (liters)
4.1/3.0
(15.5/11.4)
4.3/3.2
(16.3/12.1)
4.3/3.3
(16.3/12.5)
4.1/4.1
(15.5/15.5)
4.1/4.1
(15.5/15.5)
4.2/4.2
(15.9/15.9)
4.3/4.3
(16.3/16.3)
5.6/5.0
(21.2/19.0)
5.3/2.9
(20.1/11.0)
Minimum Load % 10%
17875
(8108)
18967
(8603)
19728
(8948)
18554
(8416)
18224
(8266)
19315
(8761)
20077
(9107)
24831
(11263)
22346
(10136)
18638
(8454)
19827
(8993)
20588
(9339)
19414
(8806)
18987
(8612)
20175
(9151)
20937
(9497)
26188
(11879)
23405
(10616)
inches (mm)
423.1
(10748)
423.1
(10748)
467.1
(11865)
379.2
(9631)
423.1
(10748)
423.1
(10748)
467.1
(11865)
511
(12979)
467.1
(11864)
inches (mm)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2243)
88.3
(2243)
inches (mm)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.7
(2405)
94.7
(2405)
Condenser Fans
Number Circuit-1/Circuit-2 10/8 10/8 8/8 8/8 9/9 9/9 10/10 14/8 13/7
°F (°C)
0°F/131°F
(-17.8°C/55°C)
71
(269)
113
(428)
113
(428)
113
(428)
71
(269)
113
(428)
113
(428)
147
(556)
96
(363)
40/70
(4.4/21.1)
psig (barg)
150
(10.3)
235
(16.2)
inches (mm)
3/4

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 27
NOTES:
tion requirements.
UNIT FRAME 37 39 41 42 42 44 47 48 50 52
CONDENSER CODE 5 8 3 5 8 3 5 3 0 3
EVAPORATOR CODE J J H H J G J G J J
GENERAL UNIT DATA
2
470/310
(213/141)
475/360
(216/163)
460/345
(209/156)
480/365
(218/166)
475/385
(215/175)
370/370
(168/168)
445/445
(202/202)
385/385
(175/175)
405/405
(184/184)
445/445
(202/202)
Oil Charge, Circuit.-1/
Circuit.-2, gal (liters)
5.6/4.3
(21.2/16.3)
5.6/5.1
(21.2/19.3)
5.5/4.3
(20.8/16.3)
5.6/4.4
(21.2/16.7)
5.6/5.1
(21.2/19.3)
5.0/5.0
(18.9/18.9)
5.8/5.8
(22.0/22.0)
5.1/5.1
(19.3/19.3)
5.2/5.2
(19.7/19.7)
5.4/5.4
(20.4/20.4)
Minimum Load % 10%
Unit shipping weight, lbs
(kg) 1
24070
(10918)
25941
(11767)
21242
(9635)
22765
(10326)
26703
(12112)
25942
(11767)
28427
(12894)
26704
(12113)
25968
(11779)
28427
(12894)
25426
(11533)
27298
(12382)
22049
(10001)
23572
(10692)
28060
(12728)
27001
(12247)
29784
(13510)
27763
(12593)
27325
(12394)
29784
(13510)
Chassis Dimensions -
Length, inches (mm)
467.1
(11864)
555.3
(14104)
467.1
(11864)
555.3
(14104)
599.3
(15222)
555.3
(14104)
599.3
(15222)
599.3
(15222)
467.1
(11865)
599.3
(15222)
Width, inches (mm)
88.3
(2243)
88.3
(2243)
88.3
(2243)
88.3
(2243)
88.3
(2243)
88.3
(2243)
88.3
(2243)
88.4
(2244)
88.3
(2243)
88.3
(2243)
Height, inches (mm)
94.7
(2405)
94.7
(2405)
94.7
(2405)
94.7
(2405)
94.7
(2405)
94.7
(2405)
94.7
(2405)
94.7
(2405)
94.7
(2405)
94.7
(2405)
CONDENSER FANS
Number Circuit-1/Circuit-2 13/7 14/10 12/8 14/10 14/12 12/12 13/13 13/13 10/10 13/13
Air on Condenser (Min/
Max), °F (°C)
0°F/131°F
(-17.8°C/55°C)
147
(556)
147
(556)
130
(492)
130
(492)
147
(556)
96
(363)
147
(556)
96
(363)
147
(556)
147
(556)
40/70
(4.4/21.1)
Maximum Water Side
150
(10.3)
235
(16.2)
Evaporator Drain
Connection, inches (mm)
3/4

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
28
Physical Data - Round Tube Coil
NOTES:
tion requirements.
UNIT FRAME 15 18 21 23 26 27 30
CONDENSER CODE 3 3 3 3 3 3 3
EVAPORATOR CODE B A A B B D C
GENERAL UNIT DATA
2
211/211
(96/96)
229/191
(104/87)
229/229
(104/104)
273/235
(124/107)
273/273
(124/124)
328/328
(149/149)
371/308
(168/140)
gal (liters)
2.1/2.0
(8.0/7.7)
2.4/2.0
(9.2/7.7)
2.5/2.5
(9.3/9.3)
2.7/2.6
(10.1/9.7)
2.7/2.7
(10.1/10.1)
3.0/3.0
(11.4/11.4)
4.1/3.0
(15.5/11.4)
Minimum Load % 10%
12354
(5224)
13064
(5926)
14113
(6402)
14542
(6596)
15539
(7048)
17738
(8046)
18786
(8521)
12815
(5813)
13505
(6126)
14554
(6602)
15004
(6806)
16001
(7258)
18566
(8421)
19549
(8867)
inches (mm)
203.3
(5163)
247
(6274)
291.2
(7397)
291.2
(7397)
335.2
(8514)
335.2
(8514)
379.2
(9631)
inches (mm)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2242)
inches (mm)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.6
(2403)
CONDENSER FANS
Number Circuit-1/Circuit-2 4/4 6/4 6/6 7/5 7/7 7/7 9/7
°F (°C)
0°F/131°F
(-17.8°C/55°C)
58
(220)
48
(182)
48
(182)
58
(220)
58
(220)
82
(310)
71
(269)
40/70
(4.4/21.1)
psig (barg)
150
(10.3)
235
(16.2)
inches (mm)
3/4

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 29
NOTES:
tion requirements.
Physical Data - Round Tube Coil (Cont'd)
UNIT FRAME 32 33 34 37 41 44 48 52
CONDENSER CODE 3 3 3 3 3 3 3 3
EVAPORATOR CODE E C E F H G G J
GENERAL UNIT DATA
2
367/367
(166/166)
371/371
(168/168)
391/391
(177/177)
537/308
(244/140)
568/417
(258/189)
478/478
(217/217)
502/502
(228/228)
562/562
(255/255)
gal (liters)
4.1/4.1
(15.5/15.5)
4.1/4.1
(15.5/15.5)
4.2/4.2
(15.9/15.9)
5.3/2.9
(20.1/11.0)
5.5/4.3
(20.8/16.3)
5.0/5.0
(18.9/18.9)
5.1/5.1
(19.3/19.3)
5.8/5.8
(22.0/22.0)
Minimum Load % 10%
20226
(9174)
20105
(9119)
21196
(9614)
24436
(11084)
23332
(10583)
28450
(12905)
29421
(13345)
31144
(14127)
21086
(9504)
20868
(9466)
22056
(10004)
25495
(11564)
24139
(10949)
29509
(13385)
30480
(13826)
32501
(14742)
inches (mm)
379.2
(9631)
423.1
(10748)
423.1
(10748)
467.1
(11864)
467.1
(11864)
555.3
(14104)
599.3
(15222)
599.3
(15222)
inches (mm)
88.3
(2242)
88.3
(2242)
88.3
(2242)
88.3
(2243)
88.3
(2243)
88.3
(2243)
88.4
(2244)
88.3
(2243)
inches (mm)
94.6
(2403)
94.6
(2403)
94.6
(2403)
94.7
(2405)
94.7
(2405)
94.7
(2405)
94.7
(2405)
94.7
(2405)
CONDENSER FANS
Number Circuit-1/Circuit-2 8/8 9/9 9/9 13/7 12/8 12/12 13/13 13/13
°F (°C)
0°F/131°F
(-17.8°C/55°C)
113
(428)
71
(269)
113
(428)
96
(363)
130
(492)
96
(363)
96
(363)
147
(556)
40/70
(4.4/21.1)
psig (barg)
150
(10.3)
235
(16.2)
inches (mm)
3/4

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
30
Evaporator Options
OPTIONAL ONE-PASS EVAPORATOR
ALL DIMENSIONS - INCHES (MM)
YVAA
A,B C D
E
NOZZLE
SIZE
WATER
VOLUME.
GALLONS
(LITERS)
MINIMUM
CHILLED
WATER FLOW
RATE
GPM (L/S)
MAXIMUM
CHILLED
WATER FLOW
RATE
GPM (L/S)
FRAME
COND.
15 3
20.8
(528)
6.8
(173)
34.5
(876)
8
58
(220)
250
(16)
950
(60)
16 5
20.8
(528)
29.2
(742)
56.1
(1425)
8
58
(220)
250
(16)
950
(60)
17 8
20.8
(528)
34.9
(886)
70
(1778)
8
71
(269)
300
(19)
1150
(73)
18 3
19.8
(503)
17.7
(450)
56.8
(1443)
6
48
(182)
200
(13)
750
(47)
19 5
19.8
(503)
61.5
(1562)
56.7
(1440)
6
48
(182)
200
(13)
750
(47)
19 8
21
(533)
117.3
(2979)
56.1
(1425)
8
58
(220)
250
(16)
950
(60)
20 0
20.8
(528)
1.7
(43)
38.1
(968)
8
71
(269)
300
(19)
1150
(73)
21 3
19.8
(503)
61.7
(1567)
56.8
(1443)
6
48
(182)
200
(13)
750
(47)
21 5
20.8
(528)
34.9
(886)
70
(1778)
8
71
(269)
300
(19)
1150
(73)
21 8
21
(533)
78.9
(2004)
70
(1778)
8
71
(269)
300
(19)
1150
(73)
Minimum Chilled Water Flow Rate is for full load selections; Variable Primary Flow ratings as low as 50% of the minimum are permitted. Glycol
limits are higher. Please contact your Johnson Controls Sales Office for ratings and further information.

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 31
Evaporator Options (Cont'd)
YVAA
A,B C D
E
NOZZLE
SIZE
WATER
VOLUME.
GALLONS
(LITERS)
MINIMUM
CHILLED
WATER FLOW
RATE
GPM (L/S)
MAXIMUM
CHILLED
WATER FLOW
RATE
GPM (L/S)
FRAME
COND.
23 3
20.8
(528)
73.2
(1859)
56.1
(1425)
8
58
(220)
250
(16)
950
(60)
24 5
21
(533)
92.9
(2360)
56.1
(1425)
8
71
(269)
300
(19)
1150
(73)
24 8
21
(533)
122.9
(3122)
70
(1778)
8
71
(269)
300
(19)
1150
(73)
26 3
21
(533)
117.1
(2974)
56.1
(1425)
8
58
(220)
250
(16)
950
(60)
27 3
21
(533)
42.9
(1090)
70
(1778)
8
82
(310)
300
(19)
1150
(73)
27 5
22.5
(572)
44.7
(1135)
71.8
(1824)
10
113
(428)
400
(25)
1500
(95)
27 8
22.5
(572)
88.3
(2243)
71.8
(1824)
10
113
(428)
400
(25)
1500
(95)
29 5
22.5
(572)
88.6
(2250)
71.8
(1824)
10
113
(428)
400
(25)
1500
(95)
30 3
21
(533)
122.9
(3122)
70
(1778)
8
71
(269)
300
(19)
1150
(73)
30 5
21
(533)
166.9
(4239)
70
(1778)
8
71
(269)
300
(19)
1150
(73)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
32
YVAA
A,B C D
E
NOZZLE
SIZE
WATER
VOLUME.
GALLONS
(LITERS)
MINIMUM
CHILLED
WATER FLOW
RATE
GPM (L/S)
MAXIMUM
CHILLED
WATER FLOW
RATE
GPM (L/S)
FRAME
COND.
30 8
22.5
(572)
132.2
(3358)
71.8
(1824)
10
113
(428)
400
(25)
1500
(95)
31 8
22.5
(572)
176.6
(4486)
71.8
(1824)
10
113
(428)
400
(25)
1500
(95)
32 3
22.5
(572)
88.6
(2250)
71.8
(1824)
10
113
(428)
400
(25)
1500
(95)
33 3
21
(533)
166.9
(4239)
70
(1778)
8
71
(269)
300
(19)
1150
(73)
34 3
22.5
(572)
132.6
(3368)
71.8
(1824)
10
113
(428)
400
(25)
1500
(95)
34 5
22.5
(572)
176.21
(4476)
71.8
(1824)
10
113
(428)
400
(25)
1500
(95)
36 8
23.3
(592)
208.6
(5298)
83.5
(2121)
10
147
(556)
550
(35)
1880
(119)
37 3
22.3
(566)
180.9
(4595)
112.2
(2850)
10
96
(363)
460
(29)
1540
(97)
37 5
23.3
(592)
164.3
(4173)
83.4
(2118)
10
147
(556)
550
(35)
1880
(119)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 33
YVAA
A,B C D
E
NOZZLE
SIZE
WATER
VOLUME.
GALLONS
(LITERS)
MINIMUM
CHILLED
WATER FLOW
RATE
GPM (L/S)
MAXIMUM
CHILLED
WATER FLOW
RATE
GPM (L/S)
FRAME
COND.
39 8
23.3
(592)
252.5
(6414)
83.5
(2121)
10
147
(556)
550
(35)
1880
(119)
41 3
22.5
(572)
164.6
(4181)
83.8
(2129)
10
130
(492)
520
(33)
1700
(107)
42 5
22.5
(572)
252.6
(6416)
83.8
(2129)
10
130
(492)
520
(33)
1700
(107)
42 8
23.3
(592)
296.5
(7531)
83.5
(2121)
10
147
(556)
550
(35)
1880
(119)
44 3
22.3
(566)
287.1
(7292)
94.2
(2393)
10
96
(363)
460
(29)
1540
(97)
47 5
23.3
(592)
308.4
(7833)
71.5
(1816)
10
147
(556)
550
(35)
1880
(119)
48 3
22.3
(566)
331.2
(8412)
94.2
(2393)
10
96
(363)
460
(29)
1540
(97)
50 0
23.3
(592)
176.2
(4475)
71.5
(1816)
10
147
(556)
550
(35)
1880
(119)
52 3
23.3
(592)
308.4
(7833)
71.5
(1816)
10
147
(556)
550
(35)
1880
(119)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
34
YVAA
A B C D
E
NOZZLE
SIZE
F G
WATER
VOLUME
GALLONS
(LITERS)
MINIMUM
CHILLED
WATER
FLOW RATE
GPM (L/S)
MAXIMUM
CHILLED
WATER
FLOW RATE
GPM (L/S)
FRAME
COND.
15 3
15.1
(384)
11.4
(290)
6.8
(173)
– 6
34.5
(876)
–
58
(220)
250
(16)
950
(60)
16 5
15.1
(384)
11.4
(290)
29.4
(747)
– 6
56.1
(1425)
–
58
(220)
250
(16)
950
(60)
17 8
15.1
(384)
11.4
(290)
34.9
(886)
– 6
70
(1778)
–
71
(269)
300
(19)
1150
(73)
18 3
14.1
(358)
11.4
(290)
17.7
(450)
– 6
56.8
(1443)
–
48
(182)
200
(13)
750
(47)
19 5
14.1
(358)
11.4
(290)
61.5
(1562)
– 6
56.7
(1440)
–
48
(182)
200
(13)
750
(47)
19 8
15.3
(389)
11.4
(290)
117.3
(2979)
– 6
56.1
(1425)
–
58
(220)
250
(16)
950
(60)
20 0
15.1
(384)
11.4
(290)
1.7
(43)
– 6
38.1
(968)
–
71
(269)
300
(19)
1150
(73)
21 3
14.1
(358)
11.4
(290)
61.7
(1567)
– 6
58.8
(1494)
–
48
(182)
200
(13)
750
(47)
21 5
15.1
(384)
11.4
(290)
29.9
(759)
– 6
70
(1778)
–
71
(269)
300
(19)
1150
(73)
21 8
15.3
(389)
11.4
(290)
78.9
(2004)
– 6
70.3
(1786)
–
71
(269)
300
(19)
1150
(73)
LD19639
G*
A
B
F
44.2
(1122)
C
D*
E
*Only where indicated with a different length
Optional
Optional
Liquid - Out
Liquid - In
Liquid - Out
Liquid - In
STANDARD TWO-PASS, REAR INLET/OUTLET EVAPORATOR

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 35
YVAA
A B C D
E
NOZZLE
SIZE
F G
WATER
VOLUME
GALLONS
(LITERS)
MINIMUM
CHILLED
WATER
FLOW RATE
GPM (L/S)
MAXIMUM
CHILLED
WATER
FLOW RATE
GPM (L/S)
FRAME
COND.
23 3
15.1
(384)
11.4
(290)
73.3
(1862)
– 6
56.1
(1425)
–
58
(220)
250
(16)
950
(60)
24 5
15.3
(389)
11.4
(290)
29.9
(759)
– 6
56.1
(1425)
–
71
(269)
300
(19)
1150
(73)
24 8
15.3
(389)
11.4
(290)
122.9
(3122)
– 6
70
(1778)
–
71
(269)
300
(19)
1150
(73)
26 3
15.3
(389)
11.4
(290)
117.3
(2979)
– 6
56.1
(1425)
–
58
(220)
250
(16)
950
(60)
27 3
15.3
(389)
11.4
(290)
42.9
(1090)
– 6
70
(1778)
–
82
(310)
300
(19)
1150
(73)
27 5
15.5
(394)
14
(356)
44.3
(1125)
– 8
71.8
(1824)
–
113
(428)
400
(25)
1500
(95)
27 8
15
(381)
14
(356)
88.3
(2243)
– 8
71.8
(1824)
–
113
(428)
400
(25)
1500
(95)
29 5
15.5
(394)
14
(356)
88.3
(2243)
– 8
71.8
(1824)
–
113
(428)
400
(25)
1500
(95)
30 3
15.3
(389)
11.4
(290)
122.9
(3122)
– 6
70
(1778)
–
71
(269)
300
(19)
1150
(73)
30 5
15.3
(389)
11.4
(290)
166.8
(4237)
– 6
70
(1778)
–
71
(269)
300
(19)
1150
(73)
LD19639
G*
A
B
F
44.2
(1122)
C
D*
E
Optional
Optional
Liquid - Out
Liquid - In
Liquid - Out
Liquid - In

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
36
LD19639
G*
A
B
F
44.2
(1122)
C
D*
E
Optional
Optional
Liquid - Out
Liquid - In
Liquid - Out
Liquid - In
YVAA
A B C D
E
NOZZLE
SIZE
F G
WATER
VOLUME
GALLONS
(LITERS)
MINIMUM
CHILLED
WATER
FLOW RATE
GPM (L/S)
MAXIMUM
CHILLED
WATER
FLOW RATE
GPM (L/S)
FRAME
COND.
30 8
15.5
(394)
14
(356)
132.2
(3358)
– 8
83.4
(2118)
–
113
(428)
400
(25)
1500
(95)
31 8
15.5
(394)
14
(356)
176.21
(4476)
– 8
83.4
(2118)
–
113
(428)
400
(25)
1500
(95)
32 3
15.5
(394)
14
(356)
88.6
(2250)
– 8
83.4
(2118)
–
113
(428)
400
(25)
1500
(95)
33 3
15.3
(389)
11.4
(290)
166.9
(4239)
– 6
83.4
(2118)
–
71
(269)
300
(19)
1150
(73)
34 3
15.5
(394)
14
(356)
132.2
(3358)
– 8
83.4
(2118)
–
113
(428)
400
(25)
1500
(95)
34 5
15.5
(394)
14
(356)
176.2
(4475)
– 8
83.4
(2118)
–
113
(428)
400
(25)
1500
(95)
36 8
16.3
(414)
14
(356)
208.5
(5296)
– 8
83.4
(2118)
–
147
(556)
550
(35)
1880
(119)
37 3
15.8
(401)
13
(330)
180.9
(4595)
176.4
(4480)
8
112.2
(2850)
107.7
(2735)
96
(363)
460
(29)
1540
(97)
37 5
16.3
(414)
14
(356)
164.4
(4176)
– 8
83.4
(2118)
–
147
(556)
550
(35)
1880
(119)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 37
LD19639
G*
A
B
F
44.2
(1122)
C
D*
E
Optional
Optional
Liquid - Out
Liquid - In
Liquid - Out
Liquid - In
YVAA
A B C D
E
NOZZLE
SIZE
F G
WATER
VOLUME
GALLONS
(LITERS)
MINIMUM
CHILLED
WATER
FLOW RATE
GPM (L/S)
MAXIMUM
CHILLED
WATER
FLOW RATE
GPM (L/S)
FRAME
COND.
39 8
16.3
(414)
14
(356)
252.5
(6414)
– 8
83.5
(2121)
147
(556)
550
(35)
1880
(119)
41 3
15.5
(394)
14
(356)
164.6
(4181)
– 8
83.8
(2129)
130
(492)
520
(33)
1700
(107)
42 5
15.5
(394)
14
(356)
252.6
(6416)
– 8
83.8
(2129)
130
(492)
520
(33)
1700
(107)
42 8
16.3
(414)
14
(356)
296.5
(7531)
– 8
83.5
(2121)
147
(556)
550
(35)
1880
(119)
44 3
15.8
(401)
13
(330)
287.1
(7292)
282.5
(7177)
8
94.2
(2393)
89.7
(2278)
96
(363)
460
(29)
1540
(97)
47 5
16.3
(414)
14
(356)
308.4
(7833)
– 8
71.5
(1816)
–
147
(556)
550
(35)
1880
(119)
48 3
15.8
(401)
13
(330)
331.2
(8412)
326.6
(8296)
8
94.2
(2393)
89.7
(2278)
96
(363)
460
(29)
1540
(97)
50 0
16.3
(414)
14
(356)
176.2
(4475)
– 8
71.5
(1816)
–
147
(556)
550
(35)
1880
(119)
52 3
16.3
(414)
14
(356)
308.4
(7833)
– 8
71.5
(1816)
–
147
(556)
550
(35)
1880
(119)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
38
YVAA
A B C D
E
NOZZLE
SIZE
WATER
VOLUME
GALLONS
(LITERS)
MINIMUM
CHILLED
WATER FLOW
RATE
GPM (L/S)
MAXIMUM
CHILLED
WATER
FLOW RATE
GPM (L/S)
FRAME
COND.
15 3
15.1
(384)
26.5
(673)
6.8
(173)
34.5
(876)
5
58
(220)
160
(10)
600
(38)
16 5
15.1
(384)
26.5
(673)
29.2
(742)
56.1
(1425)
5
58
(220)
160
(10)
600
(38)
17 8
15.1
(384)
26.5
(673)
34.9
(886)
70
(1778)
6
71
(269)
200
(13)
750
(47)
18 3
25.5
(648)
25.5
(648)
17.7
(450)
56.8
(1443)
5
48
(182)
120
(8)
500
(32)
19 5
14.1
(358)
25.5
(648)
61.5
(1562)
56.7
(1440)
5
48
(182)
120
(8)
500
(32)
19 8
15.3
(389)
26.7
(678)
117.3
(2979)
56.1
(1425)
5
58
(220)
160
(10)
600
(38)
20 0
15.1
(384)
26.53
(674)
1.7
(43)
38.1
(968)
6
71
(269)
200
(13)
750
(47)
21 3
14.1
(358)
25.5
(648)
61.6
(1565)
58.8
(1494)
5
48
(182)
120
(8)
500
(32)
21 5
15.1
(384)
26.5
(673)
34.9
(886)
70
(1778)
6
71
(269)
200
(13)
750
(47)
21 8
15.3
(389)
26.7
(678)
78.9
(2004)
70.3
(1786)
6
71
(269)
200
(13)
750
(47)
OPTIONAL THREE-PASS REAR INLET/FRONT OUTLET EVAPORATOR
LD19641
A
C
D
B
44.2
(1122)
Liquid - In Liquid - Out

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 39
LD19641
A
C
D
B
44.2
(1122)
YVAA
A B C D
E
NOZZLE
SIZE
WATER
VOLUME
GALLONS
(LITERS)
MINIMUM
CHILLED
WATER FLOW
RATE
GPM (L/S)
MAXIMUM
CHILLED
WATER
FLOW RATE
GPM (L/S)
FRAME
COND.
23 3
14.1
(358)
25.5
(648)
73.2
(1859)
56.1
(1425)
5
58
(220)
160
(10)
600
(38)
24 5
15.3
(389)
26.7
(678)
29.9
(759)
56.1
(1425)
6
71
(269)
200
(13)
750
(47)
24 8
15.3
(389)
26.7
(678)
122.9
(3122)
70
(1778)
6
71
(269)
200
(13)
750
(47)
26 3
15.3
(389)
26.7
(678)
117.1
(2974)
56.1
(1425)
5
58
(220)
160
(10)
600
(38)
27 3
15.3
(389)
26.7
(678)
42.9
(1090)
70
(1778)
6
82
(310)
200
(13)
750
(47)
27 5
15.5
(394)
29.5
(749)
88.6
(2250)
71.8
(1824)
6
113
(428)
300
(19)
850
(54)
27 8
15.5
(394)
29.5
(749)
88.3
(2243)
71.8
(1824)
6
113
(428)
300
(19)
850
(54)
29 5
15.5
(394)
29.5
(749)
88.6
(2250)
71.8
(1824)
6
113
(428)
300
(19)
850
(54)
30 3
15.3
(389)
26.7
(678)
122.9
(3122)
70
(1778)
6
71
(269)
200
(13)
750
(47)
30 5
15.3
(389)
26.7
(678)
166.9
(4239)
70
(1778)
6
71
(269)
200
(13)
750
(47)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
40
YVAA
A B C D
E
NOZZLE
SIZE
WATER
VOLUME
GALLONS
(LITERS)
MINIMUM
CHILLED
WATER FLOW
RATE
GPM (L/S)
MAXIMUM
CHILLED
WATER
FLOW RATE
GPM (L/S)
FRAME
COND.
30 8
15
(381)
30.3
(770)
132.2
(3358)
71.8
(1824)
6
113
(428)
300
(19)
850
(54)
31 8
15
(381)
29.5
(749)
176.6
(4486)
71.8
(1824)
6
113
(428)
300
(19)
850
(54)
32 3
15.5
(394)
29.5
(749)
88.6
(2250)
71.8
(1824)
6
113
(428)
300
(19)
850
(54)
33 3
15.3
(389)
26.7
(678)
166.9
(4239)
70
(1778)
6
71
(269)
200
(13)
750
(47)
34 3
15.5
(394)
29.5
(749)
132.6
(3368)
71.8
(1824)
6
113
(428)
300
(19)
850
(54)
34 5
15.5
(394)
29.5
(749)
176.2
(4475)
71.8
(1824)
6
113
(428)
300
(19)
850
(54)
36 8
16.3
(414)
30.3
(770)
208.6
(5298)
83.5
(2121)
8
147
(556)
350
(25)
1400
(88)
37 3
15.8
(401)
28.8
(732)
180.9
(4595)
112.2
(2850)
6
94
(356)
310
(20)
1070
(68)
37 5
16.3
(414)
30.3
(770)
164.3
(4173)
83.4
(2118)
8
147
(556)
400
(25)
1400
(88)
LD19641
A
C
D
B
44.2
(1122)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 41
LD19641
A
C
D
B
44.2
(1122)
YVAA
A B C D
E
NOZZLE
SIZE
WATER
VOLUME
GALLONS
(LITERS)
MINIMUM
CHILLED
WATER FLOW
RATE
GPM (L/S)
MAXIMUM
CHILLED
WATER
FLOW RATE
GPM (L/S)
FRAME
COND.
39 8
16.3
(414)
30.3
(770)
252.5
(6414)
83.5
(2121)
8
147
(556)
400
(25)
1400
(88)
41 3
15.5
(394)
29.5
(749)
164.6
(4181)
83.8
(2129)
6
128
(485)
350
(22)
1200
(76)
42 5
15.5
(394)
29.5
(749)
252.6
(6416)
83.8
(2129)
6
128
(485)
350
(22)
1200
(76)
42 8
16.3
(414)
30.3
(770)
296.5
(7531)
83.5
(2121)
8
147
(556)
400
(25)
1400
(88)
44 3
15.8
(401)
28.8
(732)
287.1
(7292)
94.2
(2393)
6
94
(356)
310
(20)
1070
(68)
47 5
16.3
(414)
30.3
(770)
308.4
(7833)
71.5
(1816)
8
147
(556)
400
(25)
1400
(88)
48 3
15.8
(401)
28.8
(732)
331.2
(8412)
94.2
(2393)
6
94
(356)
310
(20)
1070
(68)
50 0
16.3
(414)
30.3
(770)
176.2
(4475)
71.5
(1816)
8
147
(556)
400
(25)
1400
(88)
52 3
16.3
(414)
30.3
(770)
308.4
(7833)
71.5
(1816)
8
147
(556)
400
(25)
1400
(88)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
42
Dimensions
ENGLISH AND SI DIMENSIONS
The data shown in this figure is applicable to selected typical configurations. Other config-
urations are available through our configuration/selection software. Please contact your
nearest Johnson Controls Sales Office for the chiller configuration that best matches your
specific needs.
LD18586

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 43
LENAPLORTNOC/DSV
A A
0" to 14" (0mm to 356mm) (see unit
drawing for specific detail by model)
47"
(1194mm)
Dimensions (Cont'd)
LD19666

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
44
Rigging Hole Locations
LD18582
YVAA
MODEL
DESCRIPTION A B C D E F G H
CENTER OF
GRAVITY
FRAME
COND
EVAP
X
IN
(mm)
Y
IN
(mm)
015 3 B
Rigging Hole
Location inches
(mm)
18
(464)
60
(1512)
116
(2937)
192
(4866)
102
(2578)
44
(1122)
Point Load inches
(kgs)
1035
(470)
1676
(760)
1676
(760)
1372
(622)
016 5 B
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
137
(3485)
214
(5435)
126
(3206)
44
(1122)
Point Load inches
(kgs)
624
(283)
1139
(516)
3081
(1397)
1198
(543)
017 8 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
144
(3654)
197
(5012)
260
(6593)
144
(3649)
44
(1122)
Point Load inches
(kgs)
625
(283)
1746
(792)
2573
(1167)
1287
(584)
1103
(501)
018 3 A
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
143
(3636)
220
(5598)
128
(3248)
44
(1122)
Point Load inches
(kgs)
504
(229)
1448
(657)
2890
(1311)
1142
(518)
019 5 A
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
143
(3636)
227
(5761)
272
(6920)
139
(3523)
44
(1122)
Point Load inches
(kgs)
469
(213)
1474
(669)
2778
(1260)
1389
(630)
256
(116)
019 8 B
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
137
(3484)
215
(5455)
302
(7670)
148
(3760)
44
(1122)
Point Load inches
(kgs)
416
(189)
1628
(738)
2445
(1109)
1657
(751)
717
(325)
Weights are based upon microchannel coil units.

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 45
YVAA
MODEL
DESCRIPTION I J K L M N O P
CENTER OF
GRAVITY
FRAME
COND
EVAP
X
IN
(mm)
Y
IN
(mm)
015 3 B
Rigging Hole
Location inches
(mm)
18
(464)
60
(1511)
116
(2937)
192
(4866)
102
(2578)
44
(1122)
Point Load inches
(kgs)
951
(431)
1656
(751)
1656
(751)
1495
(678)
016 5 B
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
137
(3485)
214
(5435)
126
(3206)
44
(1122)
Point Load inches
(kgs)
606
(275)
1120
(508)
3057
(1387)
1259
(571)
017 8 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
144
(3654)
197
(5012)
260
(6593)
144
(3649)
44
(1122)
Point Load inches
(kgs)
634
(288)
1612
(731)
2611
(1184)
1305
(592)
1172
(532)
018 3 A
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
143
(3636)
220
(5598)
128
(3248)
44
(1122)
Point Load inches
(kgs)
510
(231)
1416
(642)
2917
(1323)
1192
(541)
019 5 A
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
143
(3636)
227
(5761)
272
(6920)
139
(3523)
44
(1122)
Point Load inches
(kgs)
484
(219)
1422
(645)
2831
(1284)
1416
(642)
264
(120)
019 8 B
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
137
(3484)
215
(5455)
302
(7670)
148
(3760)
44
(1122)
Point Load inches
(kgs)
396
(180)
1631
(740)
2453
(1113)
1716
(779)
717
(325)
LD18582
Rigging Hole Locations (Cont'd)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
46
LD18582
YVAA
MODEL
CENTER OF
GRAVITY
FRAME
COND
EVAP
X
IN
(mm)
Y
IN
(mm)
021 3 A
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
143
(3637)
227
(5761)
272
(6920)
139
(3530)
44
(1122)
Point Load inches
(kgs)
472
(214)
1467
(665)
2822
(1280)
1411
(640)
257
(117)
021 5 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
144
(3654)
197
(5012)
260
(6593)
150
(3806)
44
(1122)
Point Load inches
(kgs)
480
(218)
1988
(902)
1988
(902)
1688
(766)
1314
(596)
021 8 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
163
(4144)
254
(6443)
324
(8218)
153
(3889)
44
(1122)
Point Load inches
(kgs)
518
(235)
2344
(1063)
3047
(1382)
1501
(681)
428
(194)
023 3 B
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
137
(3485)
215
(5456)
272
(6919)
135
(3418)
44
(1122)
Point Load inches
(kgs)
340
(154)
2054
(932)
2049
(929)
2049
(929)
143
(65)
024 5 C
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
149
(3789)
240
(6088)
324
(8218)
152
(3851)
44
(1122)
Point Load inches
(kgs)
358
(162)
2130
(966)
2982
(1352)
2151
(975)
307
(139)
024 8 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
163
(4144)
254
(6443)
347
(8825)
169
(4289)
44
(1122)
Point Load inches
(kgs)
697
(316)
1921
(871)
3078
(1396)
1741
(790)
871
(395)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 47
YVAA
MODEL
CENTER OF
GRAVITY
FRAME
COND
EVAP
X
IN
(mm)
Y
IN
(mm)
021 3 A
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
143
(3637)
227
(5761)
272
(6920)
139
(3530)
44
(1122)
Point Load inches
(kgs)
484
(220)
1419
(644)
2841
(1288)
1420
(644)
264
(120)
021 5 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
144
(3654)
197
(5012)
260
(6593)
150
(3806)
44
(1122)
Point Load inches
(kgs)
472
(214)
1935
(878)
1935
(878)
1736
(788)
1379
(626)
021 8 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
163
(4144)
254
(6443)
324
(8218)
153
(3889)
44
(1122)
Point Load inches
(kgs)
510
(231)
2282
(1035)
2967
(1346)
1743
(791)
336
(152)
023 3 B
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
137
(3485)
215
(5456)
272
(6919)
135
(3418)
44
(1122)
Point Load inches
(kgs)
329
(149)
2038
(925)
2067
(938)
2067
(938)
151
(69)
024 5 C
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
149
(3789)
240
(6088)
324
(8218)
152
(3851)
44
(1122)
Point Load inches
(kgs)
354
(160)
2079
(943)
2911
(1320)
2340
(1061)
261
(118)
024 8 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
163
(4144)
254
(6443)
347
(8825)
169
(4289)
44
(1122)
Point Load inches
(kgs)
697
(316)
1800
(817)
3169
(1437)
1773
(804)
886
(402)
LD18582

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
48
LD18582
YVAA
MODEL
CENTER OF
GRAVITY
FRAME
COND
EVAP
X
IN
(mm)
Y
IN
(mm)
026 3 B
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
137
(3484)
215
(5455)
302
(7670)
146
(3721)
44
(1122)
Point Load inches
(kgs)
513
(233)
1610
(730)
2517
(1142)
1681
(763)
717
(325)
027 3 D
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3073)
181
(4601)
264
(6717)
324
(8217)
168
(4259)
44
(1122)
Point Load inches
(kgs)
877
(398)
553
(251)
1442
(654)
3605
(1635)
1108
(502)
554
(251)
027 5 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3073)
181
(4601)
264
(6717)
324
(8218)
168
(4274)
44
(1122)
Point Load inches
(kgs)
872
(396)
569
(258)
1524
(691)
3811
(1729)
1146
(520)
573
(260)
027 8 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3073)
181
(4601)
243
(6169)
347
(8825)
178
(4525)
44
(1122)
Point Load inches
(kgs)
616
(280)
1372
(622)
1138
(516)
2845
(1290)
1937
(878)
968
(439)
029 5 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
179
(4551)
290
(7358)
347
(8825)
177
(4495)
44
(1122)
Point Load inches
(kgs)
500
(227)
1930
(875)
4518
(2049)
1506
(683)
533
(242)
030 3 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
161
(4092)
254
(6443)
347
(8825)
168
(4256)
44
(1122)
Point Load inches
(kgs)
747
(339)
1875
(850)
3196
(1450)
1749
(793)
874
(397)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 49
LD18582
YVAA
MODEL
CENTER OF
GRAVITY
FRAME
COND
EVAP
X
IN
(mm)
Y
IN
(mm)
026 3 B
Rigging Hole
Location inches
(mm)
18
(464)
60
(1533)
137
(3484)
215
(5455)
302
(7670)
146
(3721)
44
(1122)
Point Load inches
(kgs)
490
(222)
1620
(735)
2489
(1129)
1722
(781)
717
(325)
027 3 D
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3073)
181
(4601)
264
(6717)
324
(8217)
168
(4259)
44
(1122)
Point Load inches
(kgs)
808
(366)
570
(259)
1411
(640)
3527
(1600)
1214
(551)
607
(275)
027 5 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3073)
181
(4601)
264
(6717)
324
(8218)
168
(4274)
44
(1122)
Point Load inches
(kgs)
803
(364)
587
(266)
1493
(677)
3734
(1694)
1252
(568)
626
(284)
027 8 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3073)
181
(4601)
243
(6169)
347
(8825)
178
(4525)
44
(1122)
Point Load inches
(kgs)
542
(246)
1407
(638)
1099
(498)
2747
(1246)
2054
(932)
1027
(466)
029 5 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
179
(4551)
290
(7358)
347
(8825)
177
(4495)
44
(1122)
Point Load inches
(kgs)
434
(197)
1937
(879)
4698
(2131)
1566
(710)
583
(264)
030 3 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
161
(4092)
254
(6443)
347
(8825)
168
(4256)
44
(1122)
Point Load inches
(kgs)
747
(339)
1784
(809)
3464
(1571)
1785
(810)
893
(405)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
50
LD18582
YVAA
MODEL
CENTER OF
GRAVITY
FRAME
COND
EVAP
X
IN
(mm)
Y
IN
(mm)
030 5 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
161
(4092)
254
(6443)
306
(7763)
391
(9941)
180
(4566)
44
(1122)
Point Load inches
(kgs)
559
(253)
2024
(918)
3021
(1370)
2164
(981)
302
(137)
752
(341)
030 8 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3072)
179
(4549)
243
(6169)
296
(7508)
391
(9942)
204
(5172)
44
(1122)
Point Load inches
(kgs)
1113
(505)
323
(147)
2182
(990)
2182
(990)
1309
(594)
1505
(683)
753
(341)
031 8 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3072)
179
(4549)
243
(6169)
353
(8962)
435
(11059)
210
(5341)
44
(1122)
Point Load inches
(kgs)
1028
(466)
575
(261)
2009
(911)
2009
(911)
2022
(917)
1580
(717)
527
(239)
032 3 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3073)
181
(4601)
243
(6169)
347
(8825)
177
(4504)
44
(1122)
Point Load inches
(kgs)
701
(318)
1261
(572)
1250
(567)
3125
(1417)
1960
(889)
980
(445)
033 3 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
163
(4144)
254
(6443)
306
(7765)
391
(9942)
180
(4563)
44
(1122)
Point Load inches
(kgs)
550
(250)
2052
(931)
3327
(1509)
2098
(952)
333
(151)
752
(341)
034 3 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3073)
181
(4602)
243
(6170)
296
(7511)
391
(9942)
204
(5172)
44
(1122)
Point Load inches
(kgs)
1087
(493)
408
(185)
2224
(1009)
2224
(1009)
1456
(660)
1505
(683)
753
(341)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 51
YVAA
MODEL
CENTER OF
GRAVITY
FRAME
COND
EVAP
X
IN
(mm)
Y
IN
(mm)
030 5 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
161
(4092)
254
(6443)
306
(7763)
391
(9941)
180
(4566)
44
(1122)
Point Load inches
(kgs)
411
(187)
2226
(1010)
2990
(1356)
2374
(1077)
299
(136)
752
(341)
030 8 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3072)
179
(4549)
243
(6169)
296
(7508)
391
(9942)
204
(5172)
44
(1122)
Point Load inches
(kgs)
1073
(487)
398
(180)
2162
(981)
2162
(981)
1547
(702)
1505
(683)
753
(341)
031 8 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3072)
179
(4549)
243
(6169)
353
(8962)
435
(11059)
210
(5341)
44
(1122)
Point Load inches
(kgs)
988
(448)
650
(295)
1988
(902)
1988
(902)
2259
(1025)
1580
(717)
527
(239)
032 3 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3073)
181
(4601)
243
(6169)
347
(8825)
177
(4504)
44
(1122)
Point Load inches
(kgs)
604
(274)
1370
(622)
1204
(546)
3010
(1365)
2060
(934)
1030
(467)
033 3 C
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
163
(4144)
254
(6443)
306
(7765)
391
(9942)
180
(4563)
44
(1122)
Point Load inches
(kgs)
373
(169)
2354
(1068)
2951
(1338)
2387
(1083)
295
(134)
752
(341)
034 3 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3073)
181
(4602)
243
(6170)
296
(7511)
391
(9942)
204
(5172)
44
(1122)
Point Load inches
(kgs)
1038
(471)
514
(233)
2135
(968)
2135
(968)
1578
(716)
1505
(683)
753
(341)
LD18582

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
52
LD18582
YVAA
MODEL
CENTER OF
GRAVITY
FRAME
COND
EVAP
X
IN
(mm)
Y
IN
(mm)
034 5 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3073)
181
(4602)
243
(6170)
353
(8961)
435
(11059)
210
(5338)
44
(1122)
Point Load inches
(kgs)
1002
(455)
659
(299)
2048
(929)
2048
(929)
2173
(986)
1580
(717)
527
(239)
36 8 J
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
302
(7662)
392
(9957)
434
(11024)
501
(12725)
208
(5283)
46
(1168)
Point Load inches
(kgs)
142
(64)
2884
(1308)
4376
(1985)
929
(421)
1857
(842)
697
(316)
310
(141)
520
(236)
037 3 F
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
302
(7662)
435
(11059)
210
(5334)
49
(1245)
Point Load inches
(kgs)
396
(179)
2152
(976)
4507
(2044)
396
(179)
2142
(972)
881
(400)
37 5 J
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
302
(7662)
435
(11059)
198
(5029)
46
(1168)
Point Load inches
(kgs)
268
(131)
2654
(1024)
4794
(2175)
288
(131)
2430
(1102)
881
(400)
39 8 J
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
302
(7358)
435
(11059)
478
(12135)
545
(13835)
218
(5537)
46
(1168)
Point Load inches
(kgs)
101
(47)
2865
(1300)
4576
(2076)
1068
(484)
2019
(916)
72
(33)
169
(77)
1517
(688)
041 3 H
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4601)
238
(6039)
302
(7662)
435
(11059)
219
(5563)
48
(1219)
Point Load inches
(kgs)
423
(192)
2025
(918)
4375
(1984)
423
(192)
1910
(867)
881
(400)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 53
YVAA
MODEL
CENTER OF
GRAVITY
FRAME
COND
EVAP
X
IN
(mm)
Y
IN
(mm)
034 5 E
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
121
(3073)
181
(4602)
243
(6170)
353
(8961)
435
(11059)
210
(5338)
44
(1122)
Point Load inches
(kgs)
953
(432)
765
(347)
1959
(889)
1959
(889)
2295
(1041)
1580
(717)
527
(239)
36 8 J
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
302
(7662)
392
(9957)
434
(11024)
501
(12725)
208
(5283)
46
(1168)
Point Load inches
(kgs)
130
(59)
2825
(1281)
5741
(2604)
935
(424)
1871
(849)
827
(375)
312
(141)
475
(215)
037 3 F
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
302
(7662)
435
(11059)
210
(5334)
49
(1245)
Point Load inches
(kgs)
368
(167)
2116
(960)
5853
(2655)
368
(167)
2287
(1037)
881
(400)
37 5 J
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
302
(7662)
435
(11059)
198
(5029)
46
(1168)
Point Load inches
(kgs)
268
(122)
2613
(1185)
6131
(2781)
268
(122)
2574
(1168)
881
(400)
39 8 J
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
302
(7358)
435
(11059)
478
(12135)
545
(13835)
218
(5537)
46
(1168)
Point Load inches
(kgs)
108
(49)
2759
(1251)
5815
(2638)
980
(445)
2153
(977)
70
(32)
167
(76)
1504
(682)
041 3 H
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4601)
238
(6039)
302
(7662)
435
(11059)
219
(5563)
48
(1219)
Point Load inches
(kgs)
406
(184)
1977
(897)
5529
(2508)
406
(184)
2008
(911)
881
(400)
LD18582

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
54
LD18582
YVAA
MODEL
CENTER OF
GRAVITY
FRAME
COND
EVAP
X
IN
(mm)
Y
IN
(mm)
42 5 H
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
302
(7358)
435
(11059)
478
(12135)
545
(13835)
222
(5639)
46
(1168)
Point Load inches
(kgs)
85
(39)
2831
(1284)
3122
(1416)
1273
(577)
1707
(774)
74
(34)
172
(78)
1534
(696)
42 8 J
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
302
(7358)
435
(11059)
494
(12546)
572
(14541)
227
(5766)
46
(1168)
Point Load inches
(kgs)
204
(93)
2793
(1267)
5125
(2325)
71
(32)
2514
(1140)
454
(206)
1056
(479)
551
(250)
044 3 G
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
290
(7662)
435
(11059)
478
(12135)
545
(13835)
227
(5766)
46
(1168)
Point Load inches
(kgs)
189
(86)
2952
(1339)
5346
(2425)
608
(276)
2066
(937)
77
(35)
176
(80)
1557
(706)
47 5 J
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
290
(7358)
435
(11059)
494
(12546)
572
(14541)
234
(5944)
46
(1168)
Point Load inches
(kgs)
335
(152)
3102
(1407)
5541
(2513)
318
(144)
2792
(1266)
518
(235)
1055
(479)
551
(250)
048 3 G
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
290
(7358)
435
(11059)
494
(12546)
572
(14529)
234
(5944)
46
(1168)
Point Load inches
(kgs)
338
(153)
2564
(1163)
5914
(2683)
104
(47)
2308
(1047)
518
(235)
1055
(479)
551
(250)
052 3 J
Rigging Hole
Location inches
(mm)
12
(305)
73
(1854)
181
(4597)
238
(6045)
290
(7366)
435
(11049)
494
(12548)
572
(14529)
234
(5944)
46
(1168)
Point Load inches
(kgs)
335
(152)
3102
(1407)
5541
(2513)
318
(144)
2792
(1266)
518
(235)
1055
(478)
551
(250)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 55
YVAA
MODEL
CENTER OF
GRAVITY
FRAME
COND
EVAP
X
IN
(mm)
Y
IN
(mm)
42 5 H
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
302
(7358)
435
(11059)
478
(12135)
545
(13835)
222
(5639)
46
(1168)
Point Load inches
(kgs)
92
(42)
2725
(1236)
4362
(1979)
1185
(538)
1841
(835)
72
(33)
170
(77)
1520
(689)
42 8 J
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
302
(7358)
435
(11059)
494
(12546)
572
(14541)
227
(5766)
46
(1168)
Point Load inches
(kgs)
198
(90)
2927
(1328)
5792
(2627)
323
(147)
2635
(1195)
454
(206)
1056
(479)
551
(250)
044 3 G
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
290
(7358)
435
(11059)
478
(12135)
545
(13835)
227
(5766)
46
(1168)
Point Load inches
(kgs)
119
(54)
3024
(1372)
5101
(2314)
796
(361)
2117
(960)
78
(35)
176
(80)
1561
(708)
47 5 J
Rigging Hole
Location inches
(mm)
12
(314)
73
(1845)
181
(4602)
238
(6039)
290
(7358)
435
(11059)
494
(12546)
572
(14541)
234
(5944)
46
(1168)
Point Load inches
(kgs)
263
(119)
3176
(1441)
5295
(2402)
496
(225)
2858
(1296)
518
(235)
1055
(479)
551
(250)
048 3 G
Rigging Hole
Location inches
(mm)
12
(305)
73
(1854)
181
(4597)
238
(6045)
290
(7366)
435
(11049)
234
(5944)
46
(1168)
Point Load inches
(kgs)
270
(122)
2630
(1193)
5677
(2575)
282
(128)
2367
(1074)
518
(235)
1055
(479)
551
(250)
052 3 J
Rigging Hole
Location inches
(mm)
12
(305)
73
(1854)
181
(4597)
238
(6045)
290
(7366)
435
(11049)
494
(12548)
572
(14529)
234
(5944)
46
(1168)
Point Load inches
(kgs)
263
(119)
3176
(1441)
5295
(2402)
496
(225)
2858
(1296)
518
(235)
1055
(478)
551
(250)
LD18582

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
56
LD18587
Isolator Locations
YVAA
MODEL
DESCRIPTION 1 2 3 4 5 6 7 8
FRAME
COND
EVAP
15 3 B
Isolator X-Dimension
inches (mm)
10
(263)
73
(1852)
144
(3662)
193
(4900)
Isolator Y-Dimension
inches (mm)
1
(34)
Point Load lbs
(kgs)
1055
(479)
2150
(975)
2150
(975)
635
(288)
16 5 B
inches (mm)
10
(263)
77
(1943)
118
(3000)
157
(3985)
220
(5589)
inches (mm)
1
(34)
Point Load lbs
(kgs)
883
(401)
764
(347)
1788
(811)
1788
(811)
1048
(475)
17 8 C
inches (mm)
10
(263)
81
(2057)
149
(3779)
187
(4756)
251
(6368)
inches (mm)
1
(34)
Point Load lbs
(kgs)
734
(333)
2308
(1047)
1598
(725)
1598
(725)
1477
(670)
18 3 A
inches (mm)
10
(263)
76
(1943)
124
(3152)
163
(4137)
210
(5323)
inches (mm)
1
(34)
Point Load lbs
(kgs)
714
(324)
1658
(752)
1089
(494)
1089
(494)
1655
(751)
19 5 A
inches (mm)
10
(259)
76
(1939)
118
(2997)
157
(3982)
208
(5295)
281
(7132)
inches (mm)
1
(34)
Point Load lbs
(kgs)
851
(386)
851
(386)
1315
(596)
2167
(983)
701
(318)
701
(318)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 57
YVAA
MODEL
DESCRIPTION 9 10 11 12 13 14 15 16
FRAME
COND
EVAP
15 3 B
inches (mm)
10
(263)
73
(1852)
144
(3662)
193
(4900)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
981
(445)
2119
(961)
2119
(961)
771
(350)
16 5 B
inches (mm)
10
(263)
77
(1943)
118
(3000)
157
(3985)
220
(5589)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
865
(392)
736
(334)
1786
(810)
1786
(810)
1100
(499)
17 8 C
inches (mm)
10
(263)
81
(2057)
149
(3779)
187
(4756)
251
(6368)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
726
(329)
2201
(998)
1616
(733)
1616
(733)
1557
(706)
18 3 A
inches (mm)
10
(263)
76
(1943)
124
(3152)
163
(4137)
210
(5323)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
708
(321)
1652
(749)
1085
(492)
1085
(492)
1725
(782)
19 5 A
inches (mm)
10
(259)
76
(1939)
118
(2997)
157
(3982)
208
(5295)
281
(7132)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
845
(383)
845
(383)
1289
(585)
2224
(1009)
717
(325)
717
(325)
LD18587
Isolator Locations (Cont'd)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
58
LD18587
YVAA
MODEL
FRAME
COND
EVAP
19 8 B
inches (mm)
10
(263)
76
(1943)
118
(3000)
157
(3985)
209
(5299)
308
(7823)
inches (mm)
1
(34)
Point Load lbs
(kgs)
620
(281)
2105
(955)
664
(301)
664
(301)
2438
(1106)
603
(274)
20 0 C
inches (mm)
10
(263)
76
(1943)
118
(3000)
157
(3985)
209
(5299)
281
(7136)
inches (mm)
1
(34)
Point Load lbs
(kgs)
853
(387)
853
(387)
1324
(601)
2202
(999)
709
(322)
709
(322)
21 3 A
inches (mm)
10
(263)
81
(2057)
149
(3779)
187
(4756)
251
(6368)
inches (mm)
1
(34)
Point Load lbs
(kgs)
661
(300)
2075
(941)
1706
(774)
1706
(774)
1692
(767)
21 5 C
inches (mm)
10
(263)
81
(2057)
149
(3779)
187
(4756)
235
(5968)
301
(7653)
inches (mm)
1
(34)
Point Load lbs
(kgs)
717
(325)
2727
(1237)
564
(256)
564
(256)
2431
(1103)
1216
(552)
21 8 C
inches (mm)
10
(263)
76
(1943)
118
(2999)
157
(3984)
209
(5298)
281
(7135)
inches (mm)
1
(34)
Point Load lbs
(kgs)
950
(431)
950
(431)
1426
(647)
2226
(1010)
658
(298)
658
(298)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 59
YVAA
MODEL
DESCRIPTION 9 10 11 12 13 14 15 16
FRAME
COND
EVAP
19 8 B
inches (mm)
10
(263)
76
(1943)
118
(3000)
157
(3985)
209
(5299)
308
(7823)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
600
(272)
2121
(962)
655
(297)
655
(297)
2511
(1139)
603
(274)
20 0 C
inches (mm)
10
(263)
76
(1943)
118
(3000)
157
(3985)
209
(5299)
281
(7136)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
847
(384)
847
(384)
1293
(586)
2228
(1011)
717
(325)
717
(325)
21 3 A
inches (mm)
10
(263)
81
(2057)
149
(3779)
187
(4756)
251
(6368)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
655
(297)
1990
(903)
1711
(776)
1711
(776)
1771
(803)
21 5 C
inches (mm)
10
(263)
81
(2057)
149
(3779)
187
(4756)
235
(5968)
301
(7653)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
704
(319)
2650
(1202)
571
(259)
571
(259)
2482
(1126)
1241
(563)
21 8 C
inches (mm)
10
(263)
76
(1943)
118
(2999)
157
(3984)
209
(5298)
281
(7135)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
936
(425)
936
(425)
1433
(650)
2243
(1017)
669
(303)
669
(303)
LD18587

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
60
LD18587
YVAA
MODEL
FRAME
COND
EVAP
23 3 B
inches (mm)
10
(263)
76
(1943)
128
(3260)
173
(4391)
220
(5579)
301
(7654)
inches (mm)
1
(34)
Point Load lbs
(kgs)
813
(369)
1915
(869)
1459
(662)
1459
(662)
1775
(805)
887
(402)
24 5 C
inches (mm)
10
(263)
81
(2057)
143
(3638)
187
(4748)
245
(6232)
339
(8609)
inches (mm)
1
(34)
Point Load lbs
(kgs)
663
(301)
1795
(814)
2030
(921)
2030
(921)
1086
(493)
1086
(493)
24 8 C
inches (mm)
10
(263)
76
(1943)
118
(2999)
157
(3984)
209
(5298)
308
(7823)
inches (mm)
1
(34)
Point Load lbs
(kgs)
699
(317)
2111
(958)
694
(315)
694
(315)
2468
(1119)
604
(274)
26 3 B
inches (mm)
10
(263)
81
(2057)
161
(4084)
201
(5105)
301
(7654)
inches (mm)
1
(34)
Point Load lbs
(kgs)
712
(323)
1544
(700)
2775
(1259)
2134
(968)
1387
(629)
27 3 D
inches (mm)
10
(263)
81
(2057)
161
(4084)
201
(5105)
301
(7654)
inches (mm)
1
(34)
Point Load lbs
(kgs)
691
(313)
1646
(747)
2871
(1302)
2282
(1035)
1435
(651)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 61
YVAA
MODEL
DESCRIPTION 9 10 11 12 13 14 15 16
FRAME
COND
EVAP
23 3 B
inches (mm)
10
(263)
76
(1943)
128
(3260)
173
(4391)
220
(5579)
301
(7654)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
807
(366)
1825
(828)
1482
(672)
1482
(672)
1821
(826)
910
(413)
24 5 C
inches (mm)
10
(263)
81
(2057)
143
(3638)
187
(4748)
245
(6232)
339
(8609)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
663
(301)
1646
(747)
2097
(951)
2097
(951)
1102
(500)
1102
(500)
24 8 C
inches (mm)
10
(263)
76
(1943)
118
(2999)
157
(3984)
209
(5298)
308
(7823)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
680
(308)
2126
(964)
671
(304)
671
(304)
2518
(1142)
604
(274)
26 3 B
inches (mm)
10
(263)
81
(2057)
161
(4084)
201
(5105)
301
(7654)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
682
(309)
1377
(625)
3032
(1375)
1944
(882)
1516
(688)
27 3 D
inches (mm)
10
(263)
81
(2057)
161
(4084)
201
(5105)
301
(7654)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
662
(300)
1480
(671)
3128
(1419)
2092
(949)
1564
(709)
LD18587

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
62
LD18587
YVAA
MODEL
FRAME
COND
EVAP
27 5 E
inches (mm)
10
(263)
81
(2057)
161
(4084)
201
(5105)
298
(7582)
339
(8609)
inches (mm)
1
(34)
Point Load lbs
(kgs)
652
(296)
1773
(804)
2533
(1149)
2533
(1149)
907
(411)
907
(411)
27 8 E
inches (mm)
10
(263)
81
(2057)
161
(4095)
201
(5105)
296
(7512)
339
(8609)
inches (mm)
1
(34)
Point Load lbs
(kgs)
693
(314)
1821
(826)
2532
(1148)
2532
(1148)
919
(417)
919
(417)
29 5 E
inches (mm)
10
(263)
81
(2057)
143
(3638)
187
(4748)
245
(6232)
339
(8609)
inches (mm)
1
(34)
Point Load lbs
(kgs)
711
(323)
1804
(818)
2071
(939)
2071
(939)
1083
(491)
1083
(491)
30 3 C
inches (mm)
10
(263)
81
(2057)
144
(3663)
187
(4755)
277
(7047)
383
(9726)
inches (mm)
1
(34)
Point Load lbs
(kgs)
870
(395)
1451
(658)
2185
(991)
2185
(991)
1652
(749)
861
(391)
30 5 C
inches (mm)
10
(260)
81
(2054)
161
(4081)
201
(5102)
298
(7579)
383
(9723)
inches (mm)
1
(34)
Point Load lbs
(kgs)
800
(363)
2001
(908)
2138
(970)
2138
(970)
1857
(842)
863
(391)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 63
YVAA
MODEL
DESCRIPTION 9 10 11 12 13 14 15 16
FRAME
COND
EVAP
27 5 E
inches (mm)
10
(263)
81
(2057)
161
(4084)
201
(5105)
298
(7582)
339
(8609)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
598
(271)
1733
(786)
2527
(1146)
2527
(1146)
961
(436)
961
(436)
27 8 E
inches (mm)
10
(263)
81
(2057)
161
(4095)
201
(5105)
296
(7512)
339
(8609)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
629
(285)
1830
(830)
2621
(1189)
2621
(1189)
973
(441)
973
(441)
29 5 E
inches (mm)
10
(259)
81
(2055)
143
(3635)
187
(4745)
245
(6228)
339
(8606)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
711
(323)
1668
(757)
2245
(1018)
2245
(1018)
1092
(495)
1092
(495)
30 3 C
inches (mm)
10
(263)
81
(2057)
144
(3663)
187
(4755)
277
(7047)
383
(9726)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
765
(347)
1551
(704)
2240
(1016)
2240
(1016)
1779
(807)
861
(391)
30 5 C
inches (mm)
10
(260)
81
(2054)
161
(4081)
201
(5102)
298
(7579)
383
(9723)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
789
(358)
1968
(893)
2235
(1014)
2235
(1014)
1938
(879)
863
(391)
LD18587

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
64
YVAA
MODEL
FRAME
COND
EVAP
30 8 E
inches (mm)
10
(263)
81
(2057)
161
(4084)
201
(5105)
298
(7582)
427
(10843)
inches (mm)
1
(34)
Point Load lbs
(kgs)
788
(357)
2032
(922)
2067
(938)
2067
(938)
2211
(1003)
1013
(459)
31 8 E
inches (mm)
10
(263)
81
(2057)
161
(4084)
201
(5105)
298
(7582)
339
(8609)
inches (mm)
1
(34)
Point Load lbs
(kgs)
702
(318)
1771
(803)
2699
(1224)
2699
(1224)
918
(416)
918
(416)
32 3 E
inches (mm)
10
(263)
81
(2057)
161
(3636)
201
(4781)
298
(6232)
339
(9726)
inches (mm)
1
(34)
Point Load lbs
(kgs)
575
(261)
2930
(1329)
891
(404)
891
(404)
3346
(1518)
861
(391)
33 3 C
inches (mm)
10
(260)
81
(2054)
161
(4081)
201
(5102)
298
(7579)
383
(9723)
inches (mm)
1
(34)
Point Load lbs
(kgs)
801
(363)
1996
(905)
2260
(1025)
2260
(1025)
1909
(866)
863
(391)
34 3 E
inches (mm)
10
(263)
81
(2057)
161
(4084)
201
(5105)
298
(7582)
427
(10843)
inches (mm)
1
(34)
Point Load lbs
(kgs)
789
(358)
2027
(919)
2188
(992)
2188
(992)
2263
(1026)
1013
(459)
LD18587

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 65
YVAA
MODEL
DESCRIPTION 9 10 11 12 13 14 15 16
FRAME
COND
EVAP
30 8 E
inches (mm)
10
(263)
81
(2057)
161
(4084)
201
(5105)
298
(7582)
427
(10843)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
778
(353)
1999
(907)
2164
(982)
2164
(982)
2292
(1040)
1013
(459)
31 8 E
inches (mm)
10
(263)
81
(2057)
161
(4084)
201
(5105)
298
(7582)
339
(8609)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
635
(288)
1794
(814)
2675
(1213)
2675
(1213)
963
(437)
963
(437)
32 3 E
inches (mm)
10
(263)
81
(2057)
143
(3636)
188
(4781)
245
(6232)
383
(9726)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
441
(200)
3177
(1441)
707
(321)
707
(321)
3601
(1633)
861
(391)
33 3 C
inches (mm)
10
(260)
81
(2054)
161
(4081)
201
(5102)
298
(7579)
383
(9723)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
789
(358)
1967
(892)
2259
(1025)
2259
(1025)
1951
(885)
863
(391)
34 3 E
inches (mm)
10
(263)
81
(2057)
161
(4084)
201
(5105)
298
(7582)
427
(10843)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
778
(353)
1998
(906)
2187
(992)
2187
(992)
2305
(1046)
1013
(459)
LD18587

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
66
YVAA
MODEL
FRAME
COND
EVAP
34 5 E
inches (mm)
10
(263)
81
(2057)
161
(2908)
201
(5219)
298
(7218)
427
(10843)
inches (mm)
1
(34)
Point Load lbs
(kgs)
789
(355)
2027
(1188)
2188
(1403)
2188
(1403)
2263
(1388)
1013
(460)
36 8 J
inches (mm)
10
(254)
81
(2057)
145
(3683)
205
(5207)
284
(7214)
383
(9728)
439
(11151)
495
(12573)
inches (mm)
1
(34)
Point Load lbs
(kgs)
710
(322)
1869
(848)
2719
(1233)
2719
(1233)
2969
(1347)
250
(113)
742
(337)
416
(189)
37 3 F
inches (mm)
10
(263)
81
(2057)
145
(3680)
206
(5219)
284
(7218)
427
(10842)
inches (mm)
1
(34)
Point Load lbs
(kgs)
397
(180)
2636
(1196)
1895
(860)
1895
(860)
3216
(1459)
964
(437)
37 5 J
inches (mm)
10
(254)
81
(2057)
145
(3683)
205
(5207)
284
(7214)
427
(10846)
inches (mm)
1
(34)
Point Load lbs
(kgs)
630
(286)
2277
(1033)
2458
(1115)
2458
(1115)
3227
(1464)
964
(437)
39 8 J
inches (mm)
10
(254)
81
(2057)
154
(3912)
206
(5232)
284
(7214)
427
(10846)
483
(12268)
539
(13691)
inches (mm)
1
(34)
Point Load lbs
(kgs)
572
(259)
2139
(970)
2845
(1291)
2845
(1291)
2859
(1297)
897
(407)
478
(217)
429
(195)
LD18587

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 67
YVAA
MODEL
DESCRIPTION 9 10 11 12 13 14 15 16
FRAME
COND
EVAP
34 5 E
inches (mm)
10
(263)
81
(2057)
161
(2908)
201
(5219)
298
(7218)
427
(10843)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
778
(349)
1998
(1179)
2187
(1398)
2187
(1398)
2305
(1412)
1013
(460)
36 8 J
inches (mm)
10
(254)
81
(2057)
145
(3683)
205
(5207)
284
(7214)
383
(9728)
439
(11151)
495
(12573)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
688
(312)
1826
(828)
3312
(1502)
3312
(1502)
3358
(1523)
46
(21)
839
(381)
413
(187)
37 3 F
inches (mm)
10
(263)
81
(2057)
145
(3680)
206
(5219)
284
(7218)
427
(10842)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
404
(183)
2486
(1128)
2575
(1168)
2575
(1168)
3399
(1542)
964
(437)
37 5 J
inches (mm)
10
(254)
81
(2057)
145
(3683)
205
(5207)
284
(7214)
427
(10846)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
646
(293)
2117
(960)
3139
(1424)
3139
(1424)
3409
(1546)
964
(437)
39 8 J
inches (mm)
10
(254)
81
(2057)
154
(3912)
206
(5232)
284
(7214)
427
(10846)
483
(12268)
539
(13691)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
547
(248)
2103
(954)
3399
(1542)
3399
(1542)
2982
(1352)
897
(407)
478
(217)
429
(195)
LD18587

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
68
YVAA
MODEL
FRAME
COND
EVAP
41 3 H
inches (mm)
10
(263)
81
(2057)
145
(3680)
205
(5219)
284
(7218)
427
(10843)
inches (mm)
1
(34)
Point Load lbs
(kgs)
496
(225)
2869
(1301)
1386
(629)
1386
(629)
3339
(1515)
964
(437)
42 5 H
inches (mm)
10
(254)
81
(2057)
154
(3907)
206
(5219)
284
(7214)
427
(10846)
483
(12243)
539
(13691)
inches (mm)
1
(34)
Point Load lbs
(kgs)
622
(282)
1876
(851)
2207
(1001)
2207
(1001)
2486
(1127)
897
(407)
478
(217)
429
(195)
42 8 J
inches (mm)
10
(254)
81
(2057)
145
(3683)
205
(5207)
284
(7214)
427
(10846)
505
(12827)
562
(14275)
inches (mm)
1
(34)
Point Load lbs
(kgs)
556
(252)
2460
(1116)
2572
(1167)
2572
(1167)
3003
(1362)
1138
(516)
382
(173)
761
(345)
44 3 G
inches (mm)
10
(263)
81
(2057)
154
(3907)
206
(5219)
284
(7218)
427
(10842)
483
(12274)
539
(13694)
inches (mm)
1
(34)
Point Load lbs
(kgs)
676
(307)
2216
(1005)
3190
(1447)
3190
(1447)
2366
(1073)
976
(443)
452
(205)
436
(198)
47 5 J
inches (mm)
10
(263)
81
(2057)
154
(3907)
206
(5219)
284
(7218)
427
(10842)
505
(12820)
562
(14265)
inches (mm)
1
(34)
Point Load lbs
(kgs)
787
(357)
2418
(1097)
3310
(1501)
3310
(1501)
2720
(1234)
1202
(545)
386
(175)
759
(344)
LD18587

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 69
YVAA
MODEL
DESCRIPTION 9 10 11 12 13 14 15 16
FRAME
COND
EVAP
41 3 H
inches (mm)
10
(263)
81
(2057)
145
(3680)
205
(5219)
284
(7218)
427
(10843)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
513
(233)
2709
(1229)
1981
(899)
1981
(899)
3462
(1570)
964
(437)
42 5 H
inches (mm)
10
(254)
81
(2057)
154
(3683)
206
(5207)
284
(7214)
427
(10846)
483
(12243)
539
(13691)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
598
(271)
1840
(835)
2760
(1252)
2760
(1252)
2608
(1183)
897
(407)
478
(217)
429
(195)
42 8 J
inches (mm)
10
(254)
81
(2057)
145
(3683)
205
(5207)
284
(7214)
427
(10846)
505
(12827)
562
(14275)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
659
(299)
2289
(1038)
3083
(1399)
3083
(1399)
3224
(1463)
1132
(513)
382
(173)
761
(345)
44 3 G
inches (mm)
10
(263)
81
(2057)
154
(3907)
206
(5219)
284
(7218)
427
(10842)
483
(12274)
539
(13694)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
657
(298)
2147
(974)
3182
(1443)
3182
(1443)
2469
(1120)
976
(443)
452
(205)
436
(198)
47 5 J
inches (mm)
10
(263)
81
(2057)
154
(3907)
206
(5219)
284
(7218)
427
(10842)
505
(12820)
562
(14265)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
765
(347)
2357
(1069)
3297
(1495)
3297
(1495)
2830
(1284)
1202
(545)
386
(175)
759
(344)
LD18587

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
70
YVAA
MODEL
FRAME
COND
EVAP
48 3 G
inches (mm)
10
(263)
81
(2057)
154
(3907)
206
(5219)
284
(7218)
427
(10842)
505
(12820)
562
(14265)
inches (mm)
1
(34)
Point Load lbs
(kgs)
686
(311)
2160
(980)
3224
(1462)
3224
(1462)
2240
(1016)
1202
(545)
386
(175)
759
(344)
50 0 J
inches (mm)
10
(263)
81
(2057)
154
(2908)
205
(5219)
284
(7218)
427
(10843)
inches (mm)
1
(34)
Point Load lbs
(kgs)
783
(355)
2619
(1188)
3093
(1403)
3093
(1403)
3061
(1388)
1014
(460)
52 3 J
inches (mm)
10
(263)
81
(2057)
154
(3907)
206
(5219)
284
(7218)
427
(10842)
505
(12820)
562
(14265)
inches (mm)
1
(34)
Point Load lbs
(kgs)
794
(360)
2611
(1184)
3112
(1412)
3112
(1412)
2916
(1323)
1202
(545)
386
(175)
759
(344)
LD18587

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 71
YVAA
MODEL
DESCRIPTION 9 10 11 12 13 14 15 16
FRAME
COND
EVAP
48 3 G
inches (mm)
10
(263)
81
(2057)
154
(3907)
206
(5219)
284
(7218)
427
(10842)
505
(12820)
562
(14265)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
667
(303)
2092
(949)
3216
(1459)
3216
(1459)
2343
(1063)
1202
(545)
386
(175)
759
(344)
50 0 J
inches (mm)
10
(263)
81
(2057)
154
(2908)
205
(5219)
284
(7218)
427
(10843)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
769
(349)
2600
(1179)
3083
(1398)
3083
(1398)
3113
(1412)
1014
(460)
52 3 J
inches (mm)
10
(263)
81
(2057)
154
(3907)
206
(5219)
284
(7218)
427
(10842)
505
(12820)
562
(14265)
inches (mm)
87
(2206)
Point Load lbs
(kgs)
772
(350)
2550
(1157)
3098
(1405)
3098
(1405)
3026
(1373)
1202
(545)
386
(175)
759
(344)
LD18587

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
72
MODEL NUMBER ISOLATOR COLOR WEIGHT RANGE (LBS)
WEIGHT RANGE
(KGS)
RD-3-CHARCOAL-WR CHARCOAL Thru 825 Thru 374
RD-4-BRICK RED-WR BRICK RED 826 - 1688 375 - 766
RD-4-CHARCOAL-WR CHARCOAL 1689 - 4000 767 - 1814
Isolators
RD-1, 2, AND 3
ISOLATORS
ELASTOMERIC ISOLATOR
LD17304
CDCD
HFHF
BT
BT
AL
L
AL
L
W
W
DW
DW
MOLDED
DURULENEMOLDED
DURULENE
R = 0.280 Slot
Typ 2 Places
Ø = AD Thru
Typ 2 Places
RD-4
ISOLATORS
MOUNT
TYPE
DIMENSION DATA (INCHES)
L W HF AL AD BT CD DW
RD1-WR 3.13 1.75 1.25 2.38 0.34 0.19 5/16-18 UNC X 3/4 1.25
RD2-WR 3.88 2.38 1.75 3.00 0.34 0.22 3/8-16 UNC X 1 1.75
RD3-WR 5.50 3.38 2.88 4.13 0.56 0.25 1/2-13 UNC X 1 2.50
RD4-WR 6.25 4.63 2.75 5.00 0.56 0.38 1/2-13 UNC X 1 3.00

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 73
W"
D"
L"B"
C"
H"
T"
5/8"
LD18442
MOUNT
TYPE
DIMENSION DATA (INCHES)
W D L B C T H
CP1 3 5/8 7–3/4 6–1/2 4–3/4 1/2 5–5/8
CP2 3 5/8 10–1/2 9–1/4 7–3/4 9/16 6
MODEL
NUMBER
RATED CAPACITY
(LBS.)
DEFLECTION
RATED (IN)
COLOR CODE
CP1-1D-85 85 1.360 LT. PURPLE
CP1-1D-120 120 1.200 DK. YELLOW
CP1-1D-175 175 1.170 DK. BLUE
CP1-1D-250 250 1.400 YELLOW
CP1-1D-340 340 1.130 RED
CP1-1D-510 510 1.020 BLACK
CP1-1D-675 675 1.320 DK. PURPLE
CP1-1D-900 900 1.020 DK. GREEN
CP1-1D-1200 1200 0.900 GRAY
CP1-1D-1360 1360 0.770 WHITE
CP1-1D-1785N 1785 0.880 GRAY/RED
MODEL
NUMBER
RATED CAPACITY
(LBS.)
DEFLECTION
RATED (IN)
COLOR CODE
CP2-1D-1020 1020 1.020 BLACK
CP2-1D-1350 1350 1.320 DK. PURPLE
CP2-1D-1800 1800 1.020 DK. GREEN
CP2-1D-2400 2400 0.900 GRAY
CP2-1D-2720 2720 0.770 WHITE
CP2-1D-3570N 3570 0.880 GRAY / RED
ONE INCH DEFLECTION SPRING ISOLATOR (CPX-X-)
Isolators (Cont'd)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
74
TWO INCH DEFLECTION, SEISMIC SPRING ISOLATOR (Y2RS-)
3/4”
7/8”
3/8” GAP
3/4”
TYP. (4)
5/8” 2-3/4”
1-1/8”
2-3/4”
8
P
4
8
STOP &
8-3/8”
OPER.
HEIGHT
4
4
LD18443
MODEL Y2RSI-2D SEISMICALLY RESTRAINED VIBRATION ISOLATOR FOR 2" DEFLECTION
SEISMIC MOUNT
SIZE
RATED LOAD
(LBS)
RATED
DEFLECTION
(IN)
SPRING RATE
(LBS/IN)
SOLID LOAD
(LBS)
COLOR CODE
ALLOWABLE
G RATING
HORIZONTAL
Y2RSI-2D-150 150 2.4 62 234 WHITE 34.7
Y2RSI-2D-320 320 2.3 140 490 YELLOW 16.3
Y2RSI-2D-460 460 2.3 200 688 GREEN 11.3
Y2RSI-2D-710 710 2.2 330 1072 DK BROWN 7.3
Y2RSI-2D-870 870 1.9 460 1312 RED 6
Y2RSI-2D-1200N 1200 1.9 638 1818 RED/BLACK 4.3
Y2RSI-2D-1450 1450 1.8 900 2450 TAN 3.6
Y2RSI-2D-1690 1690 1.7 1140 2892 PINK 3.1
Y2RSI-2D-2000N 2000 1.7 1318 3342 PINK/BLACK 2.6
Y2RSI-2D-2640N 2640 1.5 1854 4283 PINK/GRAY 2
Y2RSI-2D-2870N 3080 1.5 2004 4629
PINK/GRAY/
ORANGE
1.7
Y2RSI-2D-3280N 3740 1.8 2134 4930
PINK/GRAY/DK
BROWN
1.4
Isolators (Cont'd)

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 75

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
76
Electrical Data
FIELD WIRING LUGS
STANDARD & ULTRA QUIET CONDENSER FANS
TERMINAL
BLOCK
CIRCUIT
BREAKER
NON-FUSED
DISCONNECT SWITCH
YVAA MODEL
INPUT
VOLTS
INPUT
FREQ
WIRES
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
FRAME COND EVAP
SINGLE POINT WIRING
015 3 B
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
380 60 2 #2 - 600 kcmil 2 #2/0 ~ 500 kcmil 2 #2 - 600 kcmil
460 60 2 #2 - 600 kcmil 2 #1 ~ 500 kcmil 2 #2 - 600 kcmil
575 60 2 #2 - 600 kcmil 2 #1 ~ 500 kcmil 2 #2 ~ 600 kcmil
016 5 B
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
017 8 C
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
018 3 A
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
019 5 A
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
019 8 B
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
020 0 C
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
380 60 3 #2 - 600 kcmil 3 3/0 ~ 400 kcmil 3 #2 ~ 600 kcmil
021 3 A
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 77
FIELD WIRING LUGS
HIGH AIRFLOW/HIGH STATIC CONDENSER FANS
TERMINAL
BLOCK
CIRCUIT
BREAKER
NON-FUSED
DISCONNECT SWITCH
YVAA MODEL
INPUT
VOLTS
INPUT
FREQ
WIRE
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
FRAME COND EVAP
SINGLE POINT WIRING
015 3 B
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
016 5 B
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
017 8 C
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
018 3 A
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
019 5 A
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
019 8 B
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
020 0 C
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
021 3 A
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
Electrical Data (Cont'd)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
78
FIELD WIRING LUGS
TERMINAL
BLOCK
CIRCUIT
BREAKER
NON-FUSED
DISCONNECT SWITCH
YVAA MODEL
INPUT
VOLTS
INPUT
FREQ
WIRES
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
FRAME COND EVAP
SINGLE POINT WIRING
021 5 C
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
021 8 C
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
023 3 B
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
024 5 C
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
024 8 C
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
026 3 B
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
027 3 D
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
027 5 E
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
027 8 E
200 60 4 #2 - 600 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 79
FIELD WIRING LUGS
TERMINAL
BLOCK
CIRCUIT
BREAKER
NON-FUSED
DISCONNECT SWITCH
YVAA MODEL
INPUT
VOLTS
INPUT
FREQ
WIRE
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
FRAME COND EVAP
SINGLE POINT WIRING
021 5 C
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
021 8 C
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
023 3 B
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
575 60 2 #2 - 600 kcmil 2 #1 - 500 kcmil 2 #2 ~ 600 kcmil
024 5 C
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
024 8 C
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
026 3 B
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
027 3 D
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
027 5 E
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil
027 8 E
200 60 4 #1/0 ~ 700 kcmil
230 60 4 #2 - 600 kcmil 4 4/0 ~ 500 kcmil

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
80
FIELD WIRING LUGS
TERMINAL
BLOCK
CIRCUIT
BREAKER
NON-FUSED
DISCONNECT SWITCH
YVAA MODEL
INPUT
VOLTS
INPUT
FREQ
WIRES
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
FRAME COND EVAP
SINGLE POINT WIRING
029 5 E
200 60
230 60
380 60 3 #2 - 600 kcmil 4 #4/0 ~ 500 kcmil 4* #2 - 600 kcmil
400 50 3 #2 - 600 kcmil 4 #4/0 ~ 500 kcmil 3 #2 ~ 600 kcmil
030 3 C
200 60
230 60
030 5 C
200 60
230 60
030 8 E
200 60
230 60
031 8 E
200 60
230 60
032 3 E
200 60
230 60
033 3 C
200 60
230 60
034 3 E
200 60
230 60
034 5 E
200 60
230 60

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 81
FIELD WIRING LUGS
TERMINAL
BLOCK
CIRCUIT
BREAKER
NON-FUSED
DISCONNECT SWITCH
YVAA MODEL
INPUT
VOLTS
INPUT
FREQ
WIRE
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
FRAME COND EVAP
SINGLE POINT WIRING
029 5 E
200 60
230 60
030 3 C
200 60
230 60
030 5 C
200 60
230 60
030 8 E
200 60
230 60
031 8 E
200 60
230 60
032 3 E
200 60
230 60
033 3 C
200 60
230 60
034 3 E
200 60
230 60
034 5 E
200 60
230 60

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
82
FIELD WIRING LUGS
TERMINAL
BLOCK
CIRCUIT
BREAKER
NON-FUSED
DISCONNECT SWITCH
YVAA MODEL
INPUT
VOLTS
INPUT
FREQ
WIRES
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
FRAME COND EVAP
DUAL POINT WIRING*
036 8 J
200 60
230 60
380 60 3 #2 - 600 kcmil 3 #3/0 ~ 400 kcmil 3 #3/0 ~ 400 kcmil
037 3 F
200 60
230 60
037 5 J
200 60
230 60
039 8 J
200 60
230 60
041 3 H
200 60
230 60
042 5 H
200 60
230 60
* Note that lug data is per system on Dual Point Wiring.

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 83
FIELD WIRING LUGS
TERMINAL
BLOCK
CIRCUIT
BREAKER
NON-FUSED
DISCONNECT SWITCH
YVAA MODEL
INPUT
VOLTS
INPUT
FREQ
WIRE
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
FRAME COND EVAP
DUAL POINT WIRING*
036 8 J
200 60
230 60
037 3 F
200 60
230 60
037 5 J
200 60
230 60
039 8 J
200 60
230 60
041 3 H
200 60
230 60
042 5 H
200 60
230 60

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
84
FIELD WIRING LUGS
TERMINAL
BLOCK
CIRCUIT
BREAKER
NON-FUSED
DISCONNECT SWITCH
YVAA MODEL
INPUT
VOLTS
INPUT
FREQ
WIRES
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
FRAME COND EVAP
DUAL POINT WIRING*
042 8 J
200 60
230 60
044 3 G
200 60
230 60
047 5 J
200 60
230 60
048 3 G
200 60
230 60
050 0 J
200 60
230 60
052 3 J
200 60
230 60
FIELD WIRING LUGS TERMINAL BLOCK
TERMINAL BLOCK
WITH INDEPENDENT
SYSTEM CIRCUIT
BREAKERS
TERMINAL BLOCK WITH
INDEPENDENT SYSTEM
NON-FUSED DISCONNECT
SWITCHES
SINGLE POINT WIRING
YVAA
INPUT
VOLTS
INPUT
FREQ
WIRES
PER
PHASE
LUG WIRE
RANGE
WIRES
PER
PHASE
LUG WIRE
RANGE
WIRES PER
PHASE
LUG WIRE
RANGE
FRAME
COND
EVAP
Models
0368 to
0523
200 60
230 60
380 60 4 #1 - 750 kcmil 4 #1 - 750 kcmil 4 #1 - 750 kcmil

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 85
FIELD WIRING LUGS
TERMINAL
BLOCK
CIRCUIT
BREAKER
NON-FUSED
DISCONNECT SWITCH
YVAA MODEL
INPUT
VOLTS
INPUT
FREQ
WIRE
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE RANGE
WIRES
PER
PHASE
LUG
WIRE
RANGE
FRAME COND EVAP
DUAL POINT WIRING*
042 8 J
200 60
230 60
044 3 G
200 60
230 60
047 5 J
200 60
230 60
048 3 G
200 60
230 60
050 0 J
200 60
230 60
052 3 J
200 60
230 60

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
86
Power Wiring
STANDARD
CONTROL
TRANSFORMER
UNIT CONTROLS
EVAPORATOR HEATER
FAN
CONTACTORS
GRD
LINE
REACTOR
FIELD PROVIDED
UNIT POWER
SUPPLY
SEE NOTE 1
UNIT MOUNTED ELECTRONICS
INVERTER
1
INVERTER
2
TERMINAL BLOCK
(CIRCUIT BREAKER - OPT)
(NON-FUSED DISCONNECT
SWITCH - OPT)
SINGLE POINT WIRING
LD18588

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 87
2
DUAL POINT WIRING
Power Wiring (Cont'd)
LD18589

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
88
SYS. No. 1
ALARM
CONTACTS
SYS. No. 2
ALARM
CONTACTS
CHILLER
RUN
EVAP. PUMP
START
SIGNAL
SYS. No. 1 RUN PERM
SYS. No. 2 RUN PERM
FLOW SWITCH (-SF)
PRINT (PNT)
LEGEND
TERMINAL BLOCK FOR CUSTOMER CONNECTIONS
TERMINAL BLOCK FOR YORK CONNECTIONS
WIRING AND COMPONENTS BY YORK
OPTIONAL EQUIPMENT
WIRING AND/OR COMPONENTS BY OTHERS
RELAY
BOARD
No. 2
RELAY
BOARD
No. 1
CONTROL
BOARD
Customer Control Wiring
LD18590

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 89

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
90
Control Wiring
LD19417

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 91
Control Wiring (Cont'd)
LD19418

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
92
Guide Specifications
PART 1 - GENERAL
1.01 GENERAL REQUIREMENTS
The requirements of this Section shall conform to the general provisions of the Contract,
including General and Supplementary Conditions, Conditions of the Contract, and Con-
tract Drawings.
1.02 SCOPE
Provide Microprocessor controlled, twin-screw compressor, air-cooled, liquid chillers of
the scheduled capacities as shown and indicated on the Drawings, including but not lim-
ited to:
1. Chiller package
2. Charge of refrigerant and oil
3. Electrical power and control connections
4. Chilled liquid connections
5. Manufacturer start-up
1.03 QUALITY ASSURANCE
A. Products shall be Designed, Tested, Rated and Certified in accordance with, and In-
stalled in compliance with applicable sections of the following Standards and Codes:
1. AHRI 550/590 and 551/591 – Water Chilling Packages Using the Vapor Compres-
sion Cycle
2. AHRI 370 – Sound Rating of Large Outdoor Refrigerating and Air-Conditioning
Equipment
3. ANSI/ASHRAE 15 – Safety Code for Mechanical Refrigeration
4. ANSI/ASHRAE 34 – Number Designation and Safety Classification of Refrigerants
5. ASHRAE 90.1 – Energy Standard for Buildings Except Low-Rise Residential Build-
ings
6. ANSI/NFPA 70 – National Electrical Code (N.E.C.)
7. ASME Boiler and Pressure Vessel Code, Section VIII, Division 1
8. OSHA – Occupational Safety and Health Act
9. Manufactured in facility registered to ISO 9001
10. Conform to Intertek Testing Services for construction of chillers and provide ETL/
cETL Listed Mark

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 93
B. Factory Run Test: Chiller shall be pressure-tested, evacuated and fully charged with re-
frigerant and oil, and shall be factory operational run tested with water flowing through
the vessel.
C. Chiller manufacturer shall have a factory trained and supported service organization.
D. Warranty: Manufacturer shall Warrant all equipment and material of its manufacture
against defects in workmanship and/or material for a period of eighteen (18) months
from date of shipment or twelve (12) months from date of start-up, whichever occurs
first.
1.04 DELIVERY AND HANDLING
A. Unit shall be delivered to job site fully assembled with all interconnecting refrigerant
piping and internal wiring ready for field installation and charged with refrigerant and
oil by the Manufacturer.
B. Provide protective covering over vulnerable components for unit protection during
shipment. Fit nozzles and open ends with plastic enclosures.
C. Unit shall be stored and handled per Manufacturer’s instructions.
PART 2 - PRODUCTS
2.01 MANUFACTURERS
A. The design shown on the Drawings is based on YORK model YVAA chiller manu-
factured by Johnson Controls / YORK. Alternate equipment will be acceptable if the
manufacturer’s equipment meets the scheduled performance and complies with these
specifications. If equipment manufactured by a manufacturer other than that scheduled
is utilized, then the Mechanical Contractor shall be responsible for coordinating with
the General Contractor and all affected Subcontractors to insure proper provisions for
installation of the furnished unit. This coordination shall include, but not be limited to,
the following:
1. Structural supports for units.
2. Piping size and connection/header locations.
3. Electrical power requirements and wire/conduit and overcurrent protection sizes.
4. Chiller physical size on plant layout.
5. Site noise considerations.
B. The Mechanical Contractor shall be responsible for all costs incurred by the General
Contractor, Subcontractors, and Consultants to modify the building provisions to ac-
cept the furnished alternate equipment.
Guide Specifications (Cont'd)

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
94
2.02 GENERAL
A. Description: Furnish, Install, and Commission factory assembled, charged, and opera-
tional run tested air-cooled screw compressor chiller as specified herein and shown on
the Drawings. Chiller shall include, but is not limited to: a complete system with multiple
independent refrigerant circuits, semi hermetic twin screw compressors, shell and tube
hybrid falling film type evaporator, air-cooled condenser, R134a refrigerant, lubrica-
tion system, interconnecting wiring, safety and operating controls including capacity
controller, control center, motor starting components, and special features as specified
herein or required for safe, automatic operation.
B. Operating Characteristics:
1. Provide low and high ambient temperature control options as required to ensure unit
is capable of operation from 0°F to 131°F (-17.8°C to 55°C) ambient temperature.
2. Provide capacity control system capable of reducing unit capacity to 10% of full load
for 2 compressor units. Compressor shall start in unloaded condition. Application of
factory installed hot gas bypass shall be acceptable as required to meet specified
minimum load.
C. Cabinet: Unit panels, structural elements, control boxes and heavy gauge structural
base shall be constructed of painted galvanized steel. All exposed sheet steel shall be
coated with baked on powder paint to meet 1000-hour salt spray test in accordance
with the ASTM B117 standard.
D. Shipping: Unit shall ship in one piece and shall require installer to provide only a single
evaporator inlet and outlet pipe connection. If providing chiller model that ships in mul-
tiple pieces, bid shall include all the material and field labor costs for factory authorized
personnel to install a trim kit to connect the pieces as well as all interconnecting piping
and wiring.
2.03 COMPRESSORS
A. Compressors: Shall be direct drive, semi hermetic, rotary twin-screw type, including:
muffler, temperature actuated ‘off-cycle’ heater, rain-tight terminal box, discharge shut-
off service valve, and precision machined cast iron housing. Design working pressure
of entire compressor, suction to discharge, shall be 350 psig (24 barg) or higher. Com-
pressor shall be U.L. Recognized.
[OPTIONAL]: Suction shut-off service valve for each compressor.
B. Compressor Motors: Refrigerant suction-gas cooled accessible hermetic compressor
motor, full suction gas flow through 0.006” (0.1524 mm) maximum mesh screen, with
inherent internal thermal overload protection and external current overload on all three
phases.
C. Balancing Requirements: All rotating parts shall be statically and dynamically balanced.
D. Lubrication System: External oil separators with no moving parts, 450 psig (31 barg)
design working pressure, and ETL listing shall be provided on the chiller. Refrigerant
system differential pressure shall provide oil flow through service replaceable, 0.5 mi-
cron, full flow, cartridge type oil filter internal to compressor. Filter bypass, less restric-
tive media, or oil pump not acceptable.

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 95
E. Capacity Control: Compressors shall start at minimum load. Provide Microprocessor
control to command compressor capacity to balance compressor capacity with cooling
load.
2.04 REFRIGERANT CIRCUIT COMPONENTS
A. Refrigerant: R-134a. Classified as Safety Group A1 according to ASHRAE 34
B. Equipment supplied shall comply with LEED Energy & Atmosphere Credit 4, Enhanced
Refrigerant Management.
C. Each independent refrigerant circuit shall incorporate all components necessary for
the designed operation including: liquid line shut-off valve with charging port, low side
pressure relief device, removable core filter-drier and sight glass with moisture indica-
tor.
D. Chiller manufacturer shall provide an independent circuit for each compressor to pro-
vide maximum redundancy during chiller operation. If equipment does not have inde-
pendent circuits per compressor, manufacturer shall provide owner one spare com-
pressor of each unique size.
E. Discharge lines shall be provided with manual compressor shut-off service valves.
2.05 HEAT EXCHANGERS
A. Evaporator:
1. Evaporator shall be shell and tube, hybrid falling film type to optimize efficiency
and refrigerant charge. Tubes shall be high-efficiency, internally and externally en-
hanced type copper tubes with 0.035” (0.89 mm) minimum wall thickness at all inter-
mediate tube supports to provide maximum tube wall thickness at the support area.
Each tube shall be roller expanded into the tube sheets providing a leak proof seal,
and be individually replaceable. Independent refrigerant circuits shall be provided
per compressor.
[OPTIONAL]: 3 pass arrangement.
2. Constructed, tested, and stamped in accordance with applicable sections of ASME
pressure vessel code for minimum 235 psig (16 barg) refrigerant side design work-
ing pressure and 150 psig (10 barg) liquid side design working pressure.
3. Water boxes shall be removable to permit tube cleaning and replacement. Water
boxes shall include liquid nozzle connections suitable for ANSI/AWWA C-606 cou-
plings, welding, or flanges.
[OPTIONAL]: 150 psig (10.3 barg) ANSI raised-face weldable flanges. Flanges
are field-welded by Contractor. Companion flanges, bolts, nuts, and gaskets are
not included.
[OPTIONAL]: 150 psig (10.3 barg) ANSI raised-face flanges with ANSI/AWWA
C-606 couplings. Flanges are field-mounted by Contractor. Companion flanges,
bolts, nuts, and gaskets are not included.

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
96
[OPTIONAL]: 150 psig (10.3 barg) ANSI raised-face weldable flanges with
companion flanges. Flanges are field-welded by Contractor. Bolts, nuts, and
gaskets are not included.
[OPTIONAL]: 150 psig (10.3 barg) ANSI raised-face flanges with ANSI/AWWA
C-606 couplings with companion flanges. Flanges are field-mounted by Con-
tractor. Bolts, nuts, and gaskets are not included.
4. Provide vent and drain fittings, and thermostatically controlled heaters to protect to
0°F (-17.8°C) ambient temperature in off-cycle.
[OPTIONAL]: A separate power connection for evaporator waterbox heaters is
required to assist in freeze protection and shall be provided by the contractor.
5. Connection location: Chilled liquid inlet and outlet nozzle connections are located at
rear (opposite control panel) end of unit.
[OPTIONAL]: Inlet and outlet nozzle connections located at front end of unit.
Available for select configurations.
B. Air-cooled Condenser:
1. Condenser coils shall be microchannel type, parallel flow aluminum alloy tubes met-
allurgically brazed as one piece to enhanced aluminum alloy fins. Condenser coils
shall be made of a single material to avoid galvanic corrosion due to dissimilar met-
als. Tube and fin type condenser coils are an acceptable alternate when tubes and
fins are fabricated of the same metal material to avoid galvanic corrosion due to
dissimilar metals. Coils shall be designed for 350 psig (24 barg) or higher working
pressure.
[OPTIONAL]: Coils, internally enhanced, seamless copper tubes, mechanically
expanded into aluminum alloy fins with full height collars. Subcooling coil an in-
tegral part of condenser. Design working pressure shall be 350 PSIG (24 barg).
[OPTIONAL]: Post-coated epoxy dipped condenser microchannel: The unit
shall be built with microchannel sections that have been applied with an electro-
deposited and baked flexible epoxy coating that is finished with a polyurethane
UV resistant top-coat suitable for highly corrosive applications.
[OPTIONAL]: Wire Panels: Heavy gauge, welded wire mesh coated to resist
corrosion, to protect condenser coils from incidental damage and also restrict
unauthorized access to internal components.
[OPTIONAL]: Louvered Panels (Condenser Coils): Painted steel to match unit
panels, over external condenser coil faces.
[OPTIONAL]: Louvered Panels (Full Unit): Painted steel to match unit panels,
over internal components.
[OPTIONAL]: Louvered/Wire Panels: Louvered steel panels on external con-
denser coil faces, painted to match unit panels. Heavy gauge, welded wire
mesh, coated to resist corrosion, around base of machine to restrict unauthor-
ized access.
[OPTIONAL]: End Hail Guard: Louvered steel panels on rear of unit (opposite
end of control panel), painted to match unit panels.
[OPTIONAL]: V-Guard Panels: Steel panels installed over exposed condenser
piping to protect from damage.

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 97
2. Low Sound Fans: Shall provide vertical air discharge from extended orifices. Fans
shall be composed of corrosion resistant aluminum hub and glass-fiber-reinforced
polypropylene composite blades molded into a low-noise airfoil section. Fan impel-
ler shall be dynamically balanced for vibration-free operation. Fan guards of heavy
gauge, PVC (polyvinyl chloride) coated or galvanized steel.
[OPTIONAL]: Ultra-Quiet Fans
[OPTIONAL]: High Airflow Fans
[OPTIONAL]: High Static Fans
3. Fan Motors: High efficiency, direct drive, 3-phase, insulation class “F”, current pro-
tected, Totally Enclosed Air-Over (TEAO), with double sealed, permanently-lubricat-
ed ball bearings. Open Drip Proof (ODP) fan motors will not be acceptable.
2.06 INSULATION
A. Material: Closed-cell, flexible, UV protected, thermal insulation complying with ASTM
C 534 Type 2 (Sheet) for preformed flexible elastomeric cellular thermal insulation in
sheet and tubular form.
Thickness: 3/4” (19mm.)
[OPTIONAL]: 1-1/2” (38mm.)
B. Thermal conductivity: 0.26 (BTU/HR-Ft2-°F/in) maximum at 75°F mean temperature.
C. Factory-applied insulation over cold surfaces of liquid chiller components including
evaporator shell, water boxes, and suction line. Liquid nozzles shall be insulated by
Contractor after pipe installation.
D. Adhesive: As recommended by insulation manufacturer and applied to 100 percent of
insulation contact surface including all seams and joints.
2.07 ACOUSTICAL DATA
A. Provide acoustical sound power or sound pressure level data in decibels (dB) at the
scheduled eight (8) octave band center frequencies. A-weighted sound data alone is
not acceptable.
B. Provide all sound power or sound pressure level data at 100%, 75%, 50%, and 25%
load.
C. Supplied equipment shall not exceed scheduled sound power or sound pressure level
data at any load point. The mechanical Contractor shall be responsible for any addi-
tional costs associated with equipment deviation.
D. Acoustical performance ratings shall be in accordance with AHRI Standard 370
[OPTIONAL]: Provide factory-installed sound reduction enclosures and ultra-
quiet fans to meet chiller sound levels scheduled at all load points.
[OPTIONAL]: Provide optional control input to limit sound output of the chiller
based on time of day. Shall be programmable at the chiller panel or controlled
remotely via signal (4-20 mA or 0-10VDC) from BAS system. Chillers without
this feature shall be provided with the necessary sound attenuation to meet the
scheduled sound performance data at all load points.

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
98
2.08 POWER AND ELECTRICAL REQUIREMENTS
A. Power/Control Panel:
1. Factory installed and wired NEMA 3R, powder painted steel cabinets with tool lock-
able, hinged, latched, and gasket sealed outer doors equipped with wind struts for
safer servicing. Provide main power connection(s), compressor starters and fan
motor contactors, current overloads, and factory wiring.
2. Panel shall include control display access door.
3. Control cabinet shall be a closed design, without requirement for external airflow for
component cooling.
B. Single Point Power:
1. Provide single point power connection to chiller, shall be 3 phase of scheduled volt-
age.
2. Terminal Block connections shall be provided at the point of incoming single point
connection for field connection and interconnecting wiring to the compressors. Sep-
arate external protection must be supplied, by others, in the incoming power wiring,
which must comply with local codes.
[OPTIONAL]: Single Point Disconnect: A non-fused disconnect and lockable
external handle shall be supplied to isolate the unit power voltage for servicing.
Separate external fusing must be supplied, by others, in the incoming power
wiring which must comply with local codes.
[OPTIONAL]: Single Point Circuit Breaker: A unit-mounted Circuit Breaker with
external lockable handle shall be supplied to isolate power voltage for servic-
ing. Incoming power wiring must comply with local codes. Circuit breaker shall
be sized to provide the motor branch circuit protection, short circuit protection
and ground fault protection for the motor branch-circuit conductors, the motor
control apparatus and the motors.
C. Control Transformer: Power panel shall be supplied with a factory mounted and wired
control transformer that will supply all unit control voltage from the main unit power
supply. Transformer shall utilize scheduled line voltage on the primary side and provide
115V/1Ø on secondary.
D. Short Circuit Withstand Rating of the chiller electrical enclosure shall be (380, 400, &
460V: minimum of 30,000 Amps [OR 65,000 Amps for Single Point Circuit Breaker].)
Rating shall be published in accordance with UL508.
E. Motor Starters: Motor starters shall be zero electrical inrush current (Variable Frequen-
cy Drives) or reduced inrush type (Closed transition Wye-Delta or Solid State) for mini-
mum electrical inrush. Open transition Wye-Delta and Across the Line type starters will
not be acceptable.
F. Power Factor:
1. Provide equipment with power factor correction capacitors as required to maintain a
displacement power factor of 95% at all load conditions.
2. The installing contractor is responsible for additional cost to furnish and install pow-
er factor correction capacitors if they are not factory mounted and wired.

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 99
G. All exposed power wiring shall be routed through liquid-tight, UV-stabilized, non-me-
tallic conduit.
H. Supplied equipment shall not exceed scheduled Minimum Circuit Ampacity (MCA.) The
mechanical Contractor shall be responsible for any additional costs associated with
equipment deviation.
2.09 CONTROLS
A. General:
1. Provide automatic control of chiller operation including compressor start/stop and
load/unload, anti-recycle timers, condenser fans, evaporator pump, evaporator
heater, unit alarm contacts and run signal contacts.
2. Chiller shall automatically reset to normal chiller operation after power failure.
3. Unit operating software shall be stored in non-volatile memory. Field programmed
set points shall be retained in lithium battery backed regulated time clock (RTC)
memory for minimum 5 years.
4. Alarm contacts shall be provided to remote alert for any unit or system safety fault.
B. Display and Keypad:
1. Provide minimum 80 character liquid crystal display that is both viewable in direct
sunlight and has LED backlighting for nighttime viewing. Provide one keypad and
display panel per chiller.
2. Display and keypad shall be accessible through display access door without open-
ing main control/electrical cabinet doors.
3. Display shall provide a minimum of unit setpoints, status, electrical data, tempera-
ture data, pressures, safety lockouts and diagnostics without the use of a coded
display.
4. Descriptions in English (or available language options), numeric data in English (or
Metric) units.
5. Sealed keypad shall include unit On/Off switch.
C. Programmable Setpoints (within Manufacturer limits): Display language, chilled liquid
cooling mode, local/remote control mode, display units mode, system lead/lag control
mode, remote temperature reset, remote current limit, remote sound limit, low ambient
temperature cutout enable/disable, leaving chilled liquid setpoint and range, maximum
remote temperature reset.
D. Display Data: Chilled liquid leaving and entering temperatures; outside ambient air
temperature; lead system; evaporator pump status; active remote control; compressor
suction, discharge, and oil pressures per refrigerant circuit; compressor discharge, mo-
tor, and oil temperatures per refrigerant circuit; saturation temperatures per refrigerant
circuit; compressor speed; condenser fan status; condenser subcooling temperature;
condenser drain valve percentage open; compressor capacity in percentage of Full
Load Amps; compressor number of starts; run time; operating hours; evaporator heater
status; history data for last ten shutdown faults; history data for last 20 normal (non-
fault) shutdowns.

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
100
E. Predictive Control Points: Unit controls shall avoid safety shutdown when operating
outside design conditions by optimizing the chiller controls and cooling load output to
stay online and avoid safety limits being reached. The system shall monitor the follow-
ing parameters and maintain the maximum cooling output possible without shutdown
of the equipment: motor current, suction pressure, discharge pressure, starter internal
ambient temperature, and starter baseplate temperature.
F. System Safeties: Shall cause individual compressor systems to perform auto-reset
shut down if: high discharge pressure or temperature, low suction pressure, low motor
current, high/low differential oil pressure, low discharge superheat, high motor tem-
perature, system control voltage.
G. Unit Safeties: Shall be automatic reset and cause compressors to shut down if: high
or low ambient temperature, low leaving chilled liquid temperature, under voltage, flow
switch operation. Contractor shall provide flow switch and wiring per chiller manufac-
turer requirements.
H. Manufacturer shall provide any controls not listed above, necessary for automatic
chiller operation. Mechanical Contractor shall provide field control wiring necessary to
interface sensors to the chiller control system.
2.10 ACCESSORIES AND OPTIONS
Some accessories and options supersede standard product features. All options are fac-
tory-mounted unless otherwise noted.
A. CONTROLS OPTIONS:
1. Building Automation System Interface: Chiller to accept 4 to 20mA or 0 to 10 VDC
input from BAS (by others) to reset the leaving chilled liquid temperature or load limit
setpoint or both.
2. Gateway: Provides communication for Building Automation Systems, including
BACnet (MS/TP), Modbus, N2, and LON. (Field Commissioned by BAS Manufac-
turer)
3. Thermal Storage: Provide special control logic and modifications to produce leaving
chilled brine temperatures below 40°F (4.4°C.)
B. GENERAL OPTIONS:
1. Flow Switch: Vapor proof SPDT, NEMA 3R switch, 150 psig (10.3 barg), -20°F to
250°F (-28.9°C to 121.1°C.) (Field Mounted by Contractor)
2. Differential Pressure Switch: 3-45 psig (0.2-3 barg) range with 1/4” NPTE pressure
connections. (Field Mounted by Contractor)
3. Chicago Code Relief Valve – Special relief valves per Chicago Code
4. Special Requirement Documents:
a. Special Requirement Document Package (SRDP) includes Pressure Vessel
Report, Unit Run Test Report, Production System Check Sheet and Final Unit
Inspection Check Sheet.
b. Materials Package includes steel mill material reports for vessels in addition to
Pressure Vessel Report, Unit Run Test Report, Production System Check Sheet
and Final Unit Inspection Check Sheet.

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 101
5. Vibration Isolation (All Options Field Mounted by Contractor):
a. Elastomeric Isolators.
b. 1” Deflection Spring Isolators: Level adjustable, spring and cage type isolators
for mounting under the unit base rails.
c. 2” Deflection Restrained Spring Isolators: Level adjustable, restrained mounts
in rugged welded steel housing with vertical and horizontal limit stops. Housings
shall be designed to withstand a minimum 1.0g accelerated force in all direc-
tions to 2” (50.8 mm.)
PART 3 - EXECUTION
3.01 INSTALLATION
A. General: Rig and Install in full accordance with Manufacturer’s requirements, Project
drawings, and Contract documents.
B. Location: Locate chiller as indicated on drawings, including cleaning and service main-
tenance clearance per Manufacturer instructions. Adjust and level chiller on support
structure.
C. Components: Installing Contractor shall provide and install all auxiliary devices and
accessories for fully operational chiller.
D. Electrical: Coordinate electrical requirements and connections for all power feeds with
Electrical Contractor.
E. Controls: Coordinate all control requirements and connections with Controls Contrac-
tor.
F. Finish: Installing Contractor shall paint damaged and abraded factory finish with touch-
up paint matching factory finish.

JOHNSON CONTROLS
FORM 201.28-EG1 (915)
102
SI Metric Conversion
Values provided in this manual are in the English inch‑pound (I‑P) system.
The following factors can be used to convert from English to the most common Sl Metric values.
TEMPERATURE
To convert degrees Fahrenheit (°F) to degrees Celsius
(°C), subtract 32° and multiply by 5/9 or 0.5556.
To convert a temperature range (i.e., 10°F or 12°F chilled
water range) from Fahrenheit to Celsius, multiply by 5/9
or 0.5556.
EFFICIENCY
In the English l‑P system, chiller efficiency is measured
in kW / ton:
kW/ton =
kW input
tons refrigeration effect
In the Sl Metric system, chiller efficiency is measured in
Coefficient of Performance (COP).
kW/ton =
kW input
kW refrigeration effect
kW / ton and COP are related as follows:
kW/ton =
3.516
COP
COP =
3.516
kW/ton
MEASUREMENT
MULTIPLY THIS
ENGLISH VALUE
BY
TO OBTAIN THIS
METRIC VALUE
CAPACITY
TONS REFRIGERANT
EFFECT (ton)
3.516 KILOWATTS (kW)
POWER
KILOWATTS (kW) NO CHANGE KILOWATTS (kW)
HORSEPOWER (hp) 0.7457 KILOWATTS (kW)
FLOW RATE GALLONS / MINUTE (gpm) 0.0631 LITERS / SECOND (L/s)
LENGTH
FEET (ft) 304.8 MILLIMETERS (mm)
INCHES (in) 25.4 MILLIMETERS (mm)
WEIGHT POUNDS (lb) 0.4536 KILOGRAMS (kg)
VELOCITY FEET / SECOND (fps) 0.3048 METERS / SECOND (m/s)
PRESSURE DROP
FEET OF WATER (ft) 2.989 KILOPASCALS (kPa)
POUNDS / SQ. INCH (psi) 6.895 KILOPASCALS (k Pa)
FOULING FACTOR
ENGLISH l‑P
(fT2
°F hr/Btu)
EQUIVALENT Sl METRIC
(m2
k/kW)
0.0001 0.018
0.00025 0.044
0.0005 0.088
0.00075 0.132

FORM 201.28-EG1 (915)
JOHNSON CONTROLS 103
Notes

Printed on recycled paper
Form 201.28-EG1 (915) Supersedes: 201.28-EG1 (815)
© 2015 Johnson Controls, Inc. P.O. Box 423, Milwaukee, WI 53201 Printed in USA
www.johnsoncontrols.com
Issued on 09/01/2015

BE_YVAA_Spec_Engineering Guide

More Related Content

What's hot (20)

Similar to BE_YVAA_Spec_Engineering Guide (20)

More from Harold Schnetzka (12)

BE_YVAA_Spec_Engineering Guide