Br pdf ad_j_2010_v2

The Building Regulations 2010
Published by NBS, part of RIBA Enterprises Ltd, and available from:
RIBA Bookshops Mail Order
15 Bonhill Street
London EC2P 2EA
Telephone orders/General enquiries: 020 7256 7222
Fax orders: 020 7374 2737
Email orders: sales@ribabookshops.com
Or order online at:
www.thenbs.com/buildingregs
RIBA Bookshops
RIBA, 66 Portland Place, London WIB 1AD. Telephone 020 7256 7222
ISBN 978 1 85946 371 0
Stock code 72231
© Crown Copyright, 2010
Reprint December 2010, with corrections
Copyright in the typographical arrangement rests with the Crown.
This publication, excluding logos, may be reproduced free of charge in any format
or medium for research, private study or for internal circulation within an
organisation. This is subject to it being reproduced accurately and not used in a
misleading context. The material must be acknowledged as Crown copyright and
the title of the publication specified. This document/publication is value added.
If you wish to re-use, please apply for a Click-Use Licence for value added
material at www.opsi.gov.uk/click-use/system/online/pLogin.asp, or by writing to
the Office of Public Sector Information, Information Policy Team, Kew, Richmond,
Surrey TW9 4DU. Email: licensing@opsi.gov.uk. If you require this publication in
an alternative format please email alternativeformats@communities.gsi.gov.uk.
www.thenbs.com
BuildingRegulations2010APPROVEDDOCUMENTJCombustionappliancesandfuelstoragesystems
J1 Air supply
J2 Discharge of products of combustion
J3 Warning of release of carbon monoxide
J4 Protection of building
J5 Provision of information
J6 Protection of liquid fuel storage systems
J7 Protection against pollution
JAPPROVED DOCUMENT
Combustion appliances and
fuel storage systems
Cert no. TT-COC-002168
2010
edition
incorporating
further
2010
am
endm
ents
O N L I N E V E R S I O N
O N L I N E V E R S I O NO N L I N E V E R S I O NO N L I N E V E R S I O N

MAIN CHANGES IN THE
2004 EDITION
Section 1
New guidance has been included for access for
visual inspection of concealed flues. This should
ensure that flues can be properly inspected both
when an appliance is first commissioned and
subsequently serviced.
Section 2
Guidance has been included in support of a new
requirement J3 “Warning of release of carbon
monoxide” on the provision of carbon monoxide
alarms where solid fuel appliances are installed.
The provisions for flue outlet clearances relative
to adjacent pitched roofs have been clarified in
Diagram 17.
The guidance on the provision of hearths and
wall clearances for solid fuel appliances have
been made more flexible to take account of the
availability of modern appliances.
Section 2, 3 & 4
The guidance for permanent ventilation openings
for open flued appliances in very airtight houses
(those with a design air permeability less than or
equal to 5.0 m3/(h.m2)) have been increased to
counteract the decrease in adventitious ventilation
relative to older houses. Appendix F gives advice
on assessing the air permeability of older houses
in relation to this guidance.
Section 4
This section now explicitly includes liquid biofuel
and blends on mineral oil and liquid biofuel
within the scope of combustion installations
designed to burn oil.
Section 5
The guidance on identifying where secondary
containment for oil tanks is necessary has been
expanded to include locations in inner protection
zone as shown on the Environment Agency’s
groundwater sources map.
Appendix G
This informative appendix provides and
explanation
of the European designation system for certain flue
and chimney products.
Main changes made by the
2010 amendments
This 2010 edition, incorporating the further 2010
amendments reflects the changes made as a result
of the Building Regulations 2010 and Building
(Approved inspector etc) Regulations 2010. The
changes mainly reflect regulation number changes
as a result of re-ordering. There have been no
amendments to the substantive requirements
in Schedule 1 (i.e. Parts A to P) of the Building
Regulations.
Please note the simplification of the definition of
‘room for residential purposes’ in regulation 2 of
the Building Regulations 2010. Please also note
that L1(c) has now become regulation 40.
APPROVED DOCUMENTS
The following documents have been approved
and issued by the First Secretary of State for the
purpose of providing practical guidance with
respect to the requirements of the Building
Regulations 2010.
Approved Document A: Structure
2004 edition incorporating 2010 amendments
Approved Document B (Fire safety) – Volume
1: Dwellinghouses
Approved Document B (Fire safety) – Volume
2: Buildings other than dwellinghouses
2006 edition incorporating 2007 and 2010
amendments
Approved Document C: Site preparation and
resistance to contaminants and moisture
Approved Document D: Toxic substances
amendments
Approved Document E: Resistance to the
passage of sound
amendments
Approved Document F: Ventilation
2010 edition incorporating further 2010 amendments
Approved Document G: Sanitation, hot water
safety and water efficiency
Approved Document H: Drainage and waste
disposal
Approved Document J: Combustion
appliances and fuel storage systems
Approved Document K: Protection from falling
collision and impact
amendments
Approved Document L1A: Conservation of
fuel and power – New dwellings
Approved Document L1B: Conservation of
fuel and power – Existing dwellings
2010 edition incorporating further 2010 and 2011
amendments
Approved Document L2A: Conservation of
fuel and power – New buildings other than
dwellings
Approved Document L2B: Conservation of
fuel and power – Existing buildings other than
dwellings
2010 edition incorporating further 2010 and 2011
amendments
Approved Document M: Access to and use of
buildings
Approved Document N: Glazing – safety in
relation to impact, opening and cleaning
amendments
Approved Document P: Electrical safety –
Dwellings
Approved Document to support regulation 7:
Materials and workmanship

J
1
Approved Document J Combustion appliances and fuel storage systems
Contents
PAGE
What is an Approved Document? 3
How to use this Approved Document 3
Where you can get further help 3
Responsibility for compliance 4
The requirements 5
Limitation on requirements 5
Types of building work covered by this
Approved Document 5
Notification of work 6
Exemptions 6
Materials and workmanship 7
Supplementary guidance 7
Technical Specifications 7
Independent schemes of certification
and accreditation 7
Interaction with other legislation 8
Maintenance 8
The Requirements J1, J2, J3, J4, J5,
J6 and J7 9
Section 0: General guidance 10
Introduction to the provisions 10
Explanation of terms used 10
Measuring the size of flues and ducts 16
Section 1: Provisions which apply
generally to combustion installations 17
Performance 17
Air supply for combustion appliances 17
Permanently open ventilation of rooms 17
Permanent ventilation of appliance
compartments 17
Ventilation of other rooms or spaces 17
Permanently open air vents 19
Provisions complying with both Part F
and Part J 20
Interaction of mechanical extract
ventilation and open-flued combustion
appliances 21
Provision of flues 22
Condensates in flues 22
Construction of masonry chimneys 22
Construction of flueblock chimneys 22
Material change of use 23
PAGE
Connecting flue pipes 23
Repair of flues 23
Re-Use of existing flues 24
Use of flexible metal flue liners for the
relining of chimneys 24
Use of plastic fluepipe systems 24
Factory-made metal chimneys 24
Concealed flues 25
Configuration of natural draught flues
serving open-flued appliances 26
Inspection and cleaning openings in flues 27
Flues discharging at low level near
boundaries 27
Dry lining around fireplace openings 27
Condition of combustion installations
at completion 27
Notice Plates for hearths and flues 28
Access to combustion appliances for
maintenance 28
Section 2: Additional provisions for
appliances burning solid fuel (including
solid biofuel) with a rated output up
to 50kW 29
Air supply to appliances 29
Size of flues 29
Height of flues 30
Outlets from flues 30
Connecting fluepipes 32
Location and shielding of connecting
fluepipes 32
Debris collecting space 33
Masonry and flueblock chimneys 33
Separation of combustible material from
fireplaces and flues 34
Lining and relining of flues in chimneys 34
Formation of gathers 35
Hearths 37
Fireplace recesses and prefabricated
appliance chambers 38
Fireplace lining components 40
Walls adjacent to hearths 40
Alternative approach 40
Carbon monoxide alarms 41
JO N L I N E V E R S I O N

J
2
Combustion appliances and fuel storage systems Approved Document J
PAGE
Section 3: Additional provisions, for gas
burning appliances 43
Gas safety (Installation and Use)
Regulations 43
Gas fires (other than flueless gas fires) 45
Flueless gas appliances 45
Air supply to gas fires and other
appliances 45
Flued decorative fuel effect (DFE) fires 45
Flued appliances other than decorative
fuel effect fires 45
Air supply to flueless appliances 45
Size of natural draught flues for open
flued appliances 47
Height of natural draught flues for open
flued appliances 48
Outlets from flues 48
Provision of flues 51
Connecting fluepipe components 52
Masonry chimneys 52
Flueblock chimneys 52
Location and shielding of flues 52
Relining of flues in chimneys 52
Debris collection space for chimneys 53
Bases for back boilers 53
Hearths 54
Shielding of appliances 54
Section 4: Additional provisions for oil
burning appliances 56
Scope 56
Appliances fitted in bathrooms and
shower rooms 56
Air supply to appliances 56
Size of flues (other than balanced flues
and flues designed to discharge through
or adjacent to walls) 56
Outlets from flues and flue heights 56
Flues for oil-fired appliances: flue gas
temperature 59
Provisions for flue gas temperatures in
excess of 250°C 59
Provisions for flue gas temperatures not
exceeding 250°C 59
Connecting fluepipe components 59
PAGE
Masonry chimneys 60
Flueblock chimneys 60
Location and shielding of flues 60
Relining of flues in chimneys 60
Flues for appliances burning Class D oil 61
Hearths for oil-fired appliances 61
Shielding of oil-fired appliances 61
Section 5: Provisions for liquid fuel
storage and supply 63
Performance 63
Heating oil storage installations 63
Protective measures against fire 63
Oil supply pipe systems: means of
automatic isolation 64
Provisions where there is a risk of
oil pollution 64
LPG storage installations 64
Tank location and protective measures 65
Location and support of cylinders 65
LPG pipework (Informative) 67
APPENDICES
Appendix A: Checklist for checking
and testing of hearths, fireplaces, flues
and chimneys 68
Appendix B: Opening areas of large or
unusual fireplaces 70
Appendix C: Example calculation of the
ventilation requirements of a gas fired
appliance 71
Appendix D: Example calculation of the
ventilation requirements of an oil fired
appliance 72
Appendix E: Methods of checking
compliance with requirement J2 73
Appendix F: Assessing air permeability of
older dwellings in relation to permanent
ventilation requirements 76
Appendix G: European chimney designations 77
Appendix H: Addressees 79
Standards referred to 80
Other publications referred to 82
Index 83
J CONTENTS O N L I N E V E R S I O N

J
3
This document has been approved and issued
by the Secretary of State to provide practical
guidance on ways of complying with Requirements
J1 to J7 and regulations 7 of the Building
Regulations 2010 (SI 2010/2214) for England
and Wales. The Building Regulations 2010 are
referred to throughout the remainder of this
Document as ‘the Building Regulations’. Where
appropriate the Approved Document also gives
guidance on relevant requirements in the Building
(Approved Inspectors etc) Regulations 2010
(SI 2010/2215).
The intention of issuing Approved Documents
is to provide guidance about compliance with
specific aspects of building regulations in some
of the more common building situations. They
set out what, in ordinary circumstances, may be
reasonable provision for compliance with the
relevant requirement(s) of building regulations to
which they refer.
If guidance in an Approved Document is followed
there will be a presumption of compliance with
the requirement(s) covered by the guidance.
However, this presumption can be overturned,
so simply following guidance does not guarantee
compliance. For example, if one particular case
is unusual in some way, then ‘normal’ guidance
may not be applicable. It is also important to note
that there may well be other ways of achieving
compliance with the requirements. There is
therefore no obligation to adopt any particular
solution contained in this Approved Document
if you would prefer to meet the relevant
requirement in some other way. However,
persons intending to carry out building work
should always check with their Building
Control Body, either the local authority or
an approved inspector, that their proposals
comply with building regulations.
The guidance contained in this Approved
Document relates only to the particular
requirements of building regulations that the
document addresses (see ‘Requirements’ below).
However, building work may be subject to more
than one requirement of building regulations. In
such cases the work will also have to comply
with any other applicable requirements of
building regulations.
This document is one of a series that has been
approved and issued by the Secretary of State
for the purpose of providing practical guidance
with respect to the requirements of Schedule 1
and Regulation 7 of the Building Regulations
2010 (SI 2010/2215) for England and Wales.
At the back of this document is a list of all the
documents that have been approved and issued
by the Secretary of State for this purpose.
How to use this Approved
Document
In this document the following conventions have
been adopted to assist understanding and
interpretation:
a. Text shown against a green background are
extracts from the Building Regulations or
Building (Approved Inspectors etc) Regulations,
and set out the legal requirements that relate
to compliance with the sanitation, hot water
safety and water efficiency requirements of
building regulations. It should be remembered
however that, as noted above, building works
must comply with all the other applicable
provisions of building regulations.
b. Key terms are defined in Section 0 and are
printed in italic text.
c. Details of technical publications referred to in
the text of this Document will be given in
footnotes and repeated as end notes. A
reference to a publication is likely to be made
for one of two main reasons. The publication
may contain additional or more comprehensive
technical detail, which it would be impractical
to include in full in the Document but which is
needed to fully explain ways of meeting the
requirements; or it is a source of more general
information. The reason for the reference will
be indicated in each case. The reference will
be to a specified edition of the document.
The Approved Document may be amended
from time to time to include new references
or to refer to revised editions where this aids
compliance.
Where you can get further help
If you do not understand the technical guidance
or other information set out in this Approved
Document and the additional detailed technical
references to which it directs you, there are a
number of routes through which you can seek
further assistance:
• The Communities and Local Government
website: www.communities.gov.uk
• The Planning Portal website:
www.planningportal.gov.uk
• If you are the person undertaking the building
work you can seek assistance either from
your local authority building control service or
from your approved inspector (depending on
which building control service you are using,
or intend to use, to certify compliance of your
work with the requirements of the Building
Regulations).
What is an Approved Document?
JO N L I N E V E R S I O N

4
J WHAT IS AN APPROVED DOCUMENT?
• Persons registered with a competent person
self-certification scheme may be able to get
technical advice from their scheme operator.
• If your query is of a highly technical nature you
may wish to seek the advice of a specialist, or
industry technical body, for the relevant subject.
Responsibility for compliance
It is important to remember that if you are the
person (e.g. designer, builder, installer) carrying
out building work to which any requirement of
building regulations applies you have a
responsibility to ensure that the work complies
with any such requirement. The building owner
may also have a responsibility for ensuring
compliance with building regulation requirements
and could be served with an enforcement notice
in cases of non-compliance.
O N L I N E V E R S I O NPPROVED O N L I N E V E R S I O NPPROVED DO N L I N E V E R S I O NDOCUMENTO N L I N E V E R S I O NOCUMENT?O N L I N E V E R S I O N?

J
5
This Approved Document, which takes effect
on 1 October 2010, deals with combustion
appliances and fuel storage systems in the
Building Regulations 2010 (as amended).
Limitation on requirements
In accordance with regulation 8 of the Building
Regulations, the requirements in Parts A to D, F
to K and N and P (except for paragraphs G2, H2
and J6) of Schedule 1 to the Building Regulations
do not require anything to be done except for the
purpose of securing reasonable standards of
health and safety for persons in or about
buildings (and any others who may be affected
by buildings or matters connected with buildings).
Paragraph G2 is excluded from regulation 8 as it
deals with the conservation of water. Paragraphs
H2 and J6 are excluded from regulation 8
because they deal directly with prevention of the
contamination of water and of oil pollution. Parts
E and M (which deal, respectively, with resistance
to the passage of sound and access to and use
of buildings) are excluded from regulation 8
because they address the welfare and
convenience of building users. Part L is excluded
from regulation 8 because it addresses the
conservation of fuel and power. All these matters
are amongst the purposes, other than health and
safety that may be addressed by Building
Regulations.
Types of work covered by this
Approved Document
Building work
Building work, as defined in regulation 3 of the
Building Regulations 2010, includes the erection
and extension of a building, the provision or
extension of a controlled service or fitting, and
the material alteration of a building or a controlled
service or fitting. In addition, Building Regulations
may apply in cases where the purposes for which
or the manner or circumstances in which a
building or part of a building is used change in
the way that constitutes a material change of
use. Under regulation 4 of the Building
Regulations 2010 (as amended), building work
should be carried out in such a way that, on
completion of work,
i. the building complies with the applicable
Parts of Schedule 1 to the Building
Regulations,
ii. in the case of an extension or material
alteration of a building, or the provision,
extension or material alteration of a controlled
service or fitting, where it did not comply with
any such requirement, it is no more
unsatisfactory in relation to that requirement
than before the work was carried out.
Work described in Part J concerns the provision
or extension of controlled services or fittings.
Work associated with installations covered in
these sections may be subject to other relevant
Parts of the Building Regulations.
Material change of use
A material change of use occurs in specified
circumstances in which a building or part of a
building that was previously used for one
purpose will be used in future for another. Where
there is a material change of use the Building
Regulations set requirements that must be met
before the building can be used for its new
purpose.
Regulation 5 of the Building Regulations specifies
the following circumstances as material changes
of use:
• a building is used as a dwelling where
previously it was not.
• a building contains a flat where previously it
did not.
• a building is used as an hotel or boarding
house where previously it was not.
• a building is used as an institution where
• a building is used as a public building where
• a building no longer comes within the
exemptions in Schedule 2 to the Building
Regulations where previously it did.
• a building which contains at least one
dwelling contains a greater or lesser number
of dwellings than it did previously.
• a building contains a room for residential
purposes where previously it did not.
• a building which contains at least one room for
residential puposes contains a greater or lesser
number of such rooms than it did previously.
• a building is used as a shop where previously
it was not.
Parts J1 to J4 will apply to all the material
changes of use mentioned above which means
that whenever such changes occur the building
must be brought up to the standards required by
Parts J1 to J4.
Historic buildings
Buildings included in the schedule of monuments
maintained under section 1 of the Ancient
Monuments and Archaeological Areas Act 1979
are exempt from compliance with the requirements
of the Building Regulations.
The requirements

6
J THE REqUIREMENTS
There are other classes of buildings where special
consideration may be needed in deciding what is
adequate provision for compliance with Part J:
a. listed buildings;
b. buildings situated in designated
conservation areas;
c. buildings which are of architectural or
historic interest and which are referred
to as a material consideration in a local
authority’s development plan; and
d. buildings of architectural and historical
interest within national parks, areas of
outstanding or natural beauty and world
heritage sites.
It would not normally be considered appropriate
to relax the requirements of Part J since they
relate to health and safety. However, it may be
necessary to seek alternative technical solutions
to those set out in this approved document in
order to achieve reasonable standards of safety
without prejudicing the character of the host
building or increasing the risk of long-term
deterioration of the building’s fabric or fittings.
In determining what is appropriate in the
circumstances, the advice of the local authority’s
conservation officer should be sought. The
views of the conservation officer are particularly
important where building work requires planning
permission and/or listed building consent.
Notification of work
In almost all cases of new building work it
will be necessary to notify a Building Control
Body (BCB) in advance of any work starting.
There are two exceptions to this: where work
is carried out under a self-certification scheme
listed in Schedule 3, and where work is listed
in Schedule 4 to the Building Regulations as
being not notifiable.
Competent person self-certification schemes
under Schedule 3
Under regulation 12(6) of the Building
Regulations it is not necessary to notify a BCB
in advance of work which is covered by this
Approved Document if that work is of a type
set out in column 1 of Schedule 3 to the
Regulations and is carried out by a person
registered with a relevant self-certification
(competent persons) scheme as set out in
column 2 of that Schedule. In order to join
such a scheme a person must demonstrate
competence to carry out the type of work the
scheme covers, and also the ability to comply
with all relevant requirements in the Building
Regulations.
There are a number of schemes authorised
for the installation of combustion appliances.
Details of current schemes including those
relating to combustion appliances can
be found from www.communities.gov.uk/
planningandbuildingregulations/
competentpersonsschemes. Full details of
the schemes can be found on the individual
scheme websites.
Where work is carried out by a person registered
with a competent person scheme, regulation
20 of the Building Regulations and regulation
20(1) of the Building (Approved Inspectors etc.)
Regulations 2010 require that the occupier of
the building be given, within 30 days of the
completion of the work, a certificate confirming
that the work complies with all applicable
Building Regulation requirements. There is a also
requirement that the BCB be given a notice that
this has been done, or a copy of the certificate,
again within 30 days of the completion of the
work. These certificates and notices are usually
made available through the scheme operator.
BCBs are authorised to accept these certificates
as evidence of compliance with the requirements
of the Building Regulations. However, local
authority inspection and enforcement powers
remain unaffected, although they are normally
used only in response to a complaint that work
does not comply.
Work which is not notifiable under
Schedule 4
Schedule 4 to the Building Regulations sets out
types of work where there is no requirement
to notify a BCB that work is to be carried out.
These types of work are mainly of a minor nature
where there is no significant risk to health, safety,
water efficiency or energy efficiency. Health,
safety, and energy efficiency requirements
continue to apply to these types of work; only
the need to notify a BCB has been removed.
Where only non-notifiable work as set out in
Schedule 4 is carried out, there is no requirement
for a certificate confirming that the work
complies with Building Regulation requirements
to be given to the occupier or the BCB.
In general, all work on a combustion appliance
which is not a repair or maintenance will be
notifiable work and Schedule 4 will not apply.
However, it might be possible to add a control
device to the appliance or to alter its electrical
connection under the allowance in this schedule.
Local authority building control departments can
give advice in cases of doubt.
Exemptions
Schedule 2 to the Building Regulations sets
out a number of classes of buildings which
are exempt from all Building Regulations
requirements, including those in Part J.
O N L I N E V E R S I O NUIREMENTSO N L I N E V E R S I O NUIREMENTS

7
THE REqUIREMENTS J
Please note that the Gas Safety (Installation
and Use) Regulations apply to buildings exempt
under the Building Regulations.
Materials and workmanship
Any building work within the meaning of the
Building Regulations should, in accordance with
regulation 7, be carried out with proper materials
and in a workmanlike manner.
You may show that you have complied with
regulation 7 in a number of ways. These include
the appropriate use of a product bearing CE
marking in accordance with the Construction
Products Directive (89/106/EEC) as amended
by the CE Marking Directive (93/68/EEC)1
or a
product complying with an appropriate technical
specification (as defined in those Directives),
a British Standard or an alternative national
technical specification of any state which is a
contracting party to the European Economic
Area which in use is equivalent, or a product
covered by a national or European certificate
issued by a European Technical Approval
issuing body, and the conditions of use are in
accordance with the terms of the certificate.
You will find further guidance in the Approved
Document supporting regulation 7 on materials
and workmanship.
Supplementary guidance
The Department of Communities and Local
Government occasionally issues additional
material to aid interpretation of the guidance
in Approved Documents. This material may be
conveyed in official letters to chief executives of
local authorities and Approved Inspectors and/
or posted on the websites accessed through:
www.communities.gov.uk/planningandbuilding/
buildingregulations/.
Technical Specifications
Standards and technical approvals are relevant
guidance to the extent that they relate to health,
safety or water efficiency considerations in the
Building Regulations. They may also address
other aspects of performance such as service
ability, or aspects that, although they relate
to health and safety, are not covered by the
Building Regulations.
When an Approved Document makes reference
to a named standard, the relevant version of
the standard is the one listed at the end of
the publication. However, if this version of the
standard has been revised or updated by the
issuing standards body, the new version may be
used as a source of guidance provided that it
continues to address the relevant requirements
Regulations. Where it is proposed to work to the
1
Implemented by the Construction Products Regulations 1991
(SI/1991/1620), by the Construction Products (Amendment) Regulations
1991 (SI 1991/1620).
new version instead of the version listed at the
end of publication, this should be discussed with
BCB in advance of any work starting.
The appropriate use of a product, which
complies with a European Technical Approval
as defined in the Construction Products
Directive, (89/106/EEC) should meet the relevant
requirements.
Independent schemes of
certification and accreditation
Much of the guidance throughout this document
is given in terms of performance.
Since the performance of a system, product,
component or structure is dependent upon
satisfactory site installation, testing and
maintenance, independent schemes of
certification and accreditation of installers and
maintenance firms will provide confidence in the
appropriate standard of workmanship being
provided.
Confidence that the required level of performance
can be achieved will be demonstrated by the use
of a system, material, product or structure which
is provided under the arrangements of a product
conformity certification scheme and an
accreditation of installer scheme.
Third party accredited product conformity
certification schemes not only provide a means
of identifying materials and designs of systems,
products and structures which have demonstrated
that they reach the requisite performance, but
additionally provide confidence that the systems,
materials, products and structures actually
provided are the same specification or design as
that tested or assessed.
Third party accreditation of installers of systems,
materials, products and structures provides a
means of ensuring that installations have been
conducted by knowledgeable contractors to
appropriate standards, thereby increasing the
reliability of the anticipated performance.
Many certification bodies that approve such
schemes are accredited by the United Kingdom
Accreditation Service (UKAS).
Building Control Bodies may accept certification
of products, components, materials, or structures
under such schemes as evidence of compliance
with the relevant standard. Similarly Building
Control Bodies may accept the certification of
installation or maintenance of products,
components, materials and structures under
such schemes as evidence of compliance with
the relevant standard. Nonetheless a Building
Control Body will wish to establish in advance of
the work, that any such scheme is adequate for
the purpose of the Building Regulations.

8
J THE REqUIREMENTS
Interaction with other legislation
The Workplace (Health, Safety and Welfare)
Regulations 1992
Regulations 1992 contain some requirements
which affect building design. The main
requirements are now covered by the Building
Regulations, but for further information see:
Workplace health, safety and welfare. Workplace
(Health, Safety and Welfare) Regulations 1992.
Approved Code of Practice L24. Published by
HSE Books 1992 (ISBN 0 7176 0413 6).
Regulations 1992 apply to the common parts of
flats and similar buildings if people such as
cleaners and caretakers are employed to work in
these common parts. Where the requirements of
the Building Regulations that are covered by this
Part do not apply to dwellings, the provisions
may still be required in the situations described
above in order to satisfy the Workplace
Regulations.
The Clean Air Act 1993
Under the Clean Air Act 1993 local authorities
may declare the whole or part of the district of
the authority to be a smoke control area. It is an
offence to emit smoke from a chimney of a
building, from a furnace or from any fixed boiler
if located in a designated smoke control area
unless an authorised fuel was used. It is also an
offence to acquire an ‘unauthorised fuel’ for use
within a smoke control area unless it is used in an
‘exempt’ appliance (‘exempted’ from the controls
which generally apply in the smoke control area).
Authorised fuels are fuels which are authorised
by Statutory Instruments (Regulations) made
under the Clean Air Act 1993. These include
inherently smokeless fuels such as gas,
electricity and anthracite together with specified
brands of manufactured solid smokeless fuels.
These fuels have passed tests to confirm that
they are capable of burning in an open fireplace
without producing smoke.
Exempt appliances are appliances (ovens, wood
burners, boilers and stoves) which have been
exempted by Statutory Instruments (Orders)
under the Clean Air Act 1993. These have passed
tests to confirm that they are capable of burning
an unauthorised or inherently smoky solid fuel
without emitting smoke.
More information and details of authorised fuels
and exempt appliances can be found on the
internet at http://smokecontrol.defra.gov.uk/
Maintenance
The guidance in this Approved Document
provides a way of ensuring that combustion
appliances can function safely. For combustion
appliances to continue to work safely and
effectively it is essential that they are adequately
and regularly serviced and maintained.

J
9
This Approved Document, which takes effect
on 1 October 2010, deals with the following
Requirements which are contained in the Building
Regulations 2010 (as amended by SI 2001/2214).
Requirement Limits on application
Part J Combustion Appliances and Fuel Storage Systems
Air supply
J1. Combustion appliances shall be so installed that there is an
adequate supply of air to them for combustion, to prevent
overheating and for the efficient working of any flue.
Discharge of products of combustion
J2. Combustion appliances shall have adequate provision for
the discharge of products of combustion to the outside air.
Warning of release of carbon monoxide
J3. Where a fixed combustion appliance is provided, appropriate
provision shall be made to detect and give warning of the
release of carbon monoxide.
Protection of building
J4. Combustion appliances and fluepipes shall be so installed,
and fireplaces and chimneys shall be so constructed and installed,
as to reduce to a reasonable level the risk of people suffering
burns or the building catching fire in consequence of their use.
Provision of information
J5. Where a hearth, fireplace, flue or chimney is provided
or extended, a durable notice containing information on the
performance capabilities of the hearth, fireplace, flue or chimney
shall be affixed in a suitable place in the building for the
purpose of enabling combustion appliances to be safely installed.
Protection of liquid fuel storage systems
J6. Liquid fuel storage systems and the pipes connecting them
to combustion appliances shall be so constructed and separated
from buildings and the boundary of the premises as to reduce
to a reasonable level the risk of the fuel igniting in the event of
fire in adjacent buildings or premises.

Protection against pollution
J7. Oil storage tanks and the pipes connecting them to
combustion appliances shall:
(a) be so constructed and protected as to reduce to a reasonable
level the risk of the oil escaping and causing pollution; and
(b) have affixed in a prominent position a durable notice
containing information on how to respond to an oil escape so as
to reduce to a reasonable level the risk of pollution.
Requirements J1 and J2 apply only to fixed combustion
appliances (including incinerators).

Requirement J3 applies only to fixed combustion appliances
located in dwellings.

Requirement J6 applies only to:
(a) fixed oil storage tanks with capacities greater than 90 litres
and connecting pipes; and
(b) fixed liquefied petroleum gas storage installations with
capacities greater than 150 litres and connecting pipes, which
are located outside the building and which serve fixed
combustion appliances (including incinerators) in the building.

Requirement J7 applies only to fixed oil storage tanks with
capacities of 3500 litres or less, and connecting pipes, which:
(a) are located outside the building; and
(b) serve fixed combustion appliances (including incinerators)
in a building used wholly or mainly as a private dwelling, but
does not apply to buried systems.
Particular reference should be made to:
Approved Document B for guidance on
compartmentation of buildings for fire safety
purposes and for appropriate degrees of fire
resistance for compartment boundaries.
Approved Document F for guidance on ventilation
for health, and provision of extract ventilation
using open flued combustion appliances.
The Requirements J1/J2/J3/J4/J5/J6
COMBUSTION APPLIANCES AND FUEL STORAGE SYSTEMS JO N L I N E V E R S I O NAPPLIANCESO N L I N E V E R S I O NAPPLIANCES ANDO N L I N E V E R S I O NAND FUELO N L I N E V E R S I O NFUEL STORAGEO N L I N E V E R S I O NSTORAGE SYSTEMS O N L I N E V E R S I O NSYSTEMS

J
10
Introduction to the provisions
0.1 This Approved Document gives guidance
on how to satisfy the requirements of Part J.
Although Part J applies to the accommodation
of any combustion installation and liquid fuel
storage system within the Limits on Application,
the guidance in this Approved Document has
been prepared mainly with domestic installations
in mind, such as those comprising space and
water heating systems and cookers and their
flues, and their attendant oil and liquefied
petroleum gas (LPG) fuel storage systems. Part J
does not include specific provisions relating to
the storage of solid fuel (including solid biofuel)
but the relevant guidance in Approved Document
B should be followed.
0.2 The guidance applies to combustion
installations having power ratings and fuel
storage capacities up to the limits shown in a) to
c) below. Guidance which applies generally is
given in this section and Section 1. More specific
guidance is then given in:
a. Section 2 for solid fuel installations of up to
45kW rated output;
b. Section 3 for gas installations of up to 70kW
net (77.7kW gross) rated input;
c. Section 4 for oil installations of up to 45kW
rated heat output.
Section 5 gives guidance on requirement J5 for
heating oil storage installations with capacities
up to 3500 litres and LPG storage installations
with capacities up to 1.1 tonne, although there is
no size limit on the application of requirement J5.
Section 5 also gives guidance on requirement J6,
which is limited to installations where the capacity
of the oil storage tank is 3500 litres or less, serving
buildings used wholly or mainly as private dwellings.
0.3 For installations subject to the requirements
of part J but outside the scope of this Approved
Document, such as incinerators or installations
with higher ratings than those mentioned above,
specialist guidance may be necessary. However,
some larger installations may be shown to comply
by adopting the relevant recommendations to
be found in the CIBSE Guide B and practice
standards produced by BSI and IGEM.
Explanation of terms used
0.4 The following definitions have been
adopted solely for the purposes of providing
clarity in this Approved Document.
1. An appliance compartment is an enclosure
specifically constructed or adapted to
accommodate one or more combustion
appliances.
2. A balanced compartment is a method of
installing an open-flued appliance into a
compartment which is sealed from the
remainder of the building and whose ventilation
is so arranged in conjunction with the appliance
flue as to achieve a balanced flue effect.
3. A balanced flue appliance is a type of room-
sealed appliance which draws its combustion
air from a point outside the building adjacent
to the point at which the combustion products
are discharged, the inlet and outlet being so
disposed that wind effects are substantially
balanced. Balanced flues may run vertically,
but in the most common configuration they
discharge horizontally through the external
wall against which the appliance is situated.
4. The boundary is the boundary of the land or
buildings belonging to and under the control
of the building owner. Depending upon the
paragraphs of this Approved Document to
which it applies, it may be drawn only around
the perimeter of the land in question or
extended to the centreline of adjacent routes
or waterways as shown in Diagram 1.
5. A Building Control Body is a body that
carries out checks for compliance with the
Building Regulations on plans of building work
and on the building work itself. The Building
Control Body may be either the local authority
or an Approved Inspector. For further details,
see the manual to the Building Regulations.
6. The capacity of an oil tank is its nominal
capacity as stated by the manufacturer. It is
usually 95 per cent of the volume of liquid
required to fill it to the brim.
Section 0: General guidance
Diagram 1 Boundaries in this
Approved Document

J
11
7. A chimney is a structure consisting of a wall
or walls enclosing one or more flues (see
Diagram 2). In the gas industry, the chimney
for a gas appliance is commonly called
the flue.
8. A combustion appliance (or appliance) is an
apparatus where fuel is burned to generate
heat for space heating, water heating, cooking
or other similar purpose. The appliance does
not include systems to deliver fuel to it or for
the distribution of heat. Typical combustion
appliances are boilers, warm air heaters,
water heaters, fires, stoves and cookers.
9. The designation system in BS EN 1443:2003
expresses the performance characteristics of
a chimney or its components, as assessed in
accordance with an appropriate European
product standard, by means of a code such
as EN 1234 – T400 N1 D1 Gxx. Further
information is given in Appendix G.
Sleeve
Diagram 2 Chimneys and flues
GENERAL GUIDANCE JO N L I N E V E R S I O NGUIDANCE O N L I N E V E R S I O NGUIDANCE

J
12
10. A draught break is an opening formed by a
factory-made component into any part of the
flue serving an open-flued appliance. Such
openings may be provided to allow dilution
air to be drawn into a flue or to lessen the
effects of down-draught on combustion in
the appliance.
11. A draught diverter is a form of draught break
intended to prevent conditions in the main length
of flue from interfering with the combustion
performance of an open-flued appliance (see
Diagram 3(a)). It allows the appliance to
operate without interference from down-
draughts that may occur in adverse wind
conditions and excessive draught.
12. A draught stabiliser is a factory-made
counter-balanced flap device admitting air
to the flue, from the same space as the
combustion air, to prevent excessive variations
in the draught (see Diagram 3(b)). It is usual
for these to be in the fluepipe or chimney, but
they may be located on the appliance.
13. Equivalent area is defined in BS EN 13141
-1:2004 as the area of a sharp-edged circular
orifice which would pass the same air flow
rate at the same applied pressure difference
as the product or device being tested. The
equivalent area of a simple ventilator will be
less than the geometrical free area and for
complex products may be significantly less.
14. Factory-made metal chimneys (also known
as system chimneys) are prefabricated
chimneys that are commonly manufactured
as sets of components for assembly on site
(although they can be supplied as one unit),
having the performance appropriate for the
intended appliance. They are available in
various materials and types ranging from
single-walled metal chimneys suitable for
some gas appliances to twin-walled chimneys
with insulation sandwiched between an inner
liner and an outer metal wall which are
designed for oil or solid fuel use.
15. In a fanned draught installation, the proper
discharge of the flue gases depends upon the
operation of a fan, which may be separately
installed in the flue or may be an integral
part of the combustion appliance. Fans in
combustion appliances either may extract
flue gases from the combustion chamber or
may cause the flue gases to be displaced
from the combustion chamber if the fan
is supplying it with air for combustion.
Appliances with fans providing the combustion
air (including most oil-fired and many gas-
fired boilers) are also commonly referred to
as forced draught appliances (see Diagram
4). Flues in fanned draught installations run
horizontally or vertically and can be at higher
or lower pressures than their surroundings,
dependent upon the location of the fan.
16. A fire compartment is a building or part of
a building comprising one or more rooms,
spaces or storeys constructed to prevent
the spread of fire to or from another part of
the same building or an adjoining building.
(A roof-space above the top storey of a
fire compartment is included in that fire
compartment.) A separated part of a building
is a form of compartmentation in which part
of a building is separated from another part of
the same building by a compartment wall.
Such walls run the full height of the part and
are in one vertical plane. Further information
on this is given in Approved Document B Vol
2 (see Section 8 Compartmentation and
Appendix C Methods of Measurement).
17. A fireplace recess is a structural opening
(sometimes called a builder’s opening) formed
in a wall or in a chimney breast, from which a
chimney leads and which has a hearth at its
base. Simple structural openings (Diagram
5(a)) are suitable for closed appliances such
as stoves, cookers or boilers, but gathers
(Diagram 5(b)) are necessary for accommodating
open fires. Fireplace recesses are often lined
with firebacks to accommodate inset open
fires (Diagram 5(c)). Lining components and
decorative treatments fitted around openings
reduce the opening area. It is the finished
fireplace opening area which determines the
size of flue required for an open fire in such
a recess.
18. The fire resistance of a component or
construction is a measure of its ability to
withstand the effects of fire in one or more
ways for a stated period of time. Guidance on
determination of performance in terms of fire
resistance is given in Approved Document B
(Fire Safety).
J GENERAL GUIDANCE
Diagram 3 Draught diverter and
draught stabiliser
O N L I N E V E R S I O NGUIDANCEO N L I N E V E R S I O NGUIDANCE

J
13
19. A fire wall is a means of shielding a fuel tank
from the thermal radiation from a fire. For
LPG tanks, it also ensures that gas accidentally
leaking from the tank or fittings must travel by
a longer path and therefore disperse safely,
before reaching a hazard such as an opening
in a building, a boundary or other potential
ignition source.
20. A flue is a passage that conveys the products
of combustion from an appliance to the
outside air (see Diagram 2).
21. Flueblock chimney systems consist of a set
of factory-made components, made from
precast concrete, clay or other masonry units,
that are designed for assembly on site to
provide a complete chimney having the
performance appropriate for the intended
appliance. There are two types of common
systems, one being solely for use with gas-
burning appliances and the other, often called
chimney block systems, being primarily
designed for solid fuel-burning appliances.
GENERAL GUIDANCE J
Diagram 4 Types of installation
O N L I N E V E R S I O NGUIDANCE O N L I N E V E R S I O NGUIDANCE

14
22. A flue box is a factory made unit, usually made
of metal, which is similar to a prefabricated
appliance chamber except that it is designed
to accommodate a gas burning appliance in
conjunction with a factory-made chimney.
23. A flueless appliance is one which is designed
to be used without connection to a flue. Its
products of combustion mix with the
surrounding room air and are eventually
transported to the outside as stale air leaves
the room (see Diagram 4(g)).
24. A flue liner is the wall of the chimney that is in
contact with the products of combustion (see
Diagram 2), such as a concrete flue liner, the
inner liner of a factory-made chimney system or
a flexible liner fitted into an existing chimney.
25. A flue outlet is the point at which the products
of combustion are discharged from the flue to
the outside atmosphere, such as the top of a
chimney pot or flue terminal.
26. A fluepipe is a pipe, either single walled (bare
or insulated) or double walled, which connects
a combustion appliance to a flue in a chimney.
For clarity, when used in this way, it may be
called a connecting fluepipe. (Fluepipe is also
used to describe the tubular components
from which some factory made chimneys for
gas and oil appliances are made or from
which plastic flue systems are made).
27. A hearth is a base intended to safely isolate a
combustion appliance from people, combustible
parts of the building fabric and soft furnishings.
The exposed surface of the hearth provides a
region around the appliance which can be kept
clear of anything at risk of fire. The body of
the hearth may be thin insulating board, a
substantial thickness of material such as
concrete or some intermediate provision
dependent upon the weight and downward
heat emission characteristics of the appliance(s)
upon it (see Diagram 6).
28. The heat input rate is the maximum rate of
energy flow into an appliance. It is calculated
as the rate of fuel flow to the appliance
multiplied by either the fuel’s gross or net
calorific value.
Note: Traditionally, the UK has used Gross
values, most European standards use Net values.
Thus for gas appliances it is now the norm to
express this rating as a net value (kW (net)).
29. Installation instructions are those instructions
produced by manufacturers to enable installers
to correctly install and test appliances and
flues and to commission them into service.
30. In a natural draught flue, the combustion
products flow into the flue as a result of the
draught produced due to the difference
between the temperature of the gases within
J GENERAL GUIDANCE
Diagram 5 Fireplace recesses
O N L I N E V E R S I O NGUIDANCEO N L I N E V E R S I O NGUIDANCE

15
the flue and the temperature of the ambient
air. Taller flues produce a greater draught at
their base. Except for those balanced flue
appliances which are designed to discharge
directly through the wall adjacent to the
appliance, a satisfactory natural draught
requires an essentially vertical run of flue
(see Diagram 4 (a) and (b)).
31. Non-combustible material. This is the
highest level of reaction to fire performance.
Non-combustible materials include:
a. any material which when tested to
BS 476-11:1982 (2007) does not flame
nor cause any rise in temperature on
either the centre (specimen) or furnace
thermocouples; and
b. products classified as non-combustible
in tests following the procedures in
BS 476-4:1970 (2007);
c. any material classified as class A1 in
accordance with BS EN 13501-1:2002 Fire
classification of construction products
and building elements. Classification
using data from reaction to fire tests.
Typical examples of such materials to be
found in buildings include totally inorganic
materials such as concrete, fired clay,
ceramics, metals, plaster and masonry
containing not more than 1 per cent by
weight or volume of organic material. (Use
in buildings of combustible metals such as
magnesium–aluminium alloys should be
assessed in each individual case.)
More detailed information is given in
Approved Document B (Fire Safety).
32. A Notified Body, for the purposes of the Gas
Appliances (Safety) Regulations (1995), means:
a. a body which is approved by the Secretary of
State for Trade and Industry as being
competent to carry out the required Attestation
procedures for gas appliances and whose
name and identification number has been
notified by him/her to the Commission of the
European Community and to other member
States in accordance with the Gas Appliances
(Safety) Regulations (1995);
b. a body which has been similarly approved for
the purposes of the Gas Appliances Directive
by another member State and whose name
and identification number has been notified to
the Commission and to other member States
pursuant to the Gas Appliances Directive.
33. An open-flued appliance is one which draws
its combustion air from the room or space
within which it is installed and which requires
a flue to discharge its products of combustion
to the outside air (see Diagram 4 (a), (c) and (e)).
34. A prefabricated appliance chamber is a set
of factory-made precast concrete components
designed to provide a fireplace recess to
accommodate an appliance such as a stove,
and incorporates a gather when used with an
open fire. The chamber is normally positioned
against a wall and may be designed to
support a chimney. The chamber and
chimney are often enclosed to create a false
chimney breast (see also ‘flue box’).
35. The rated heat input (sometimes shortened
to rated input) for a gas appliance is the
maximum heat input rate at which it can be
operated, as declared on the appliance data
plate. (See also heat input rate.)
36. The rated heat output for an oil appliance is
the maximum declared energy output rate
(kW) as declared on the appliance data plate.
Diagram 6 The functions of hearths
GENERAL GUIDANCE JO N L I N E V E R S I O NGUIDANCE O N L I N E V E R S I O NGUIDANCE

J
16
37. The rated heat output for a solid fuel appliance
is the manufacturer’s declared nominal energy
output rate (kW) for the appliance. This may be
different for different fuels.
38. A room-sealed appliance means an
appliance whose combustion system is
sealed from the room in which the appliance
is located and which obtains air for
combustion from a ventilated uninhabited
space within the building or directly from the
open air outside the building and which vents
the products of combustion directly to open
air outside the building (see Diagram 4 (b), (d)
and (f)).
39. Solid biofuel means, for the purpose of this
Approved Document, a solid fuel derived
from plants and trees. It can include logs,
wood chips, wood pellets and other
processed plant material.
40. A throat is a contracted part of the flue
between a fireplace recess and its chimney
(see Diagram 22). Throats are usually formed
from prefabricated components as shown in
Diagram 29.
Measuring the size of flues
and ducts
0.5 The size a flue or duct (area, diameter etc)
should be measured at right angles to the
direction in which gases flow. Where offset
components are used, they should not reduce
the flue area to less than the minimum required
for the combustion appliance (see Diagram 7).
Diagram 7 Measurement of flues and ducts
J GENERAL GUIDANCEO N L I N E V E R S I O NGUIDANCEO N L I N E V E R S I O NGUIDANCE

J
17
Performance
1.1 In the Secretary of State’s view
requirements J1 to J5 will be met if the building
provisions for the safe accommodation of
combustion appliances:
a. enable the admission of sufficient air for:
i. the proper combustion of fuel and the
operation of flues; and
ii. the cooling of appliances where
necessary;
b. enable normal operation of appliances
without the products of combustion
becoming a hazard to health.
c. incorporate an appropriate means of warning
of a release of Carbon Monoxide for fixed
appliances that burn solid fuels;
d. enable normal operation of appliances
without their causing danger through damage
by heat or fire to the fabric of the building;
e. have been inspected and tested to establish
suitability for the purpose intended;
f. have been labelled to indicate performance
capabilities.
Note: Whilst, for the purposes of requirement
J2A, it is considered appropriate to require
carbon monoxide alarms only with solid fuel
appliances, such alarms can still reduce the risk
of poisoning from other types of appliance.
Air supply for combustion
appliances
1.2 Combustion appliances require ventilation
to supply them with air for combustion. Ventilation
is also required to ensure the proper operation
of flues or, in the case of flueless appliances, to
ensure that the products of combustion are
safely dispersed to the outside air. Installation of
room-sealed appliances or those with a directly
connected ducted external air supply will minimise
ventilation energy losses from the room and the
risk of cold draughts. In some cases, combustion
appliances may also require air for cooling control
systems and/or to ensure that casings remain
safe to touch (see Diagram 8). General guidance
on where it may be necessary to install air vents
for these purposes is given below.
1.3 Air vent sizes, which are dependent upon
the type of fuel burned, are given in Sections 2, 3
and 4 and are for one combustion appliance only.
The air supply provisions will usually need to be
increased where a room contains more than one
appliance (such as a kitchen containing an
open-flued boiler and an open-flued cooker).
Permanently open ventilation
of rooms
1.4 A room containing an open-flued appliance
may need permanently open air vents. An open-
flued appliance must receive a certain amount of
air from outside (‘combustion air’ in Diagram 8)
dependent upon its type and rating. Infiltration
through the building fabric may be sufficient
but for certain appliance ratings and forms of
construction, permanent openings are necessary
(see Diagram 8).
Permanent ventilation of appliance
compartments
1.5 Appliance compartments that enclose
open-flued combustion appliances should be
provided with vents large enough to admit all of
the air required by the appliance for combustion
and proper flue operation, whether the compartment
draws its air from a room or directly from outside
(see Diagram 8 (b) and (c)).
1.6 Where appliances require cooling air,
appliance compartments should be large enough
to enable air to circulate and high- and low-level
vents should be provided (see Diagram 8 (d), (e),
(f) and (g)).
1.7 Where appliances are to be installed within
balanced compartments (see paragraph 0.4(2)),
special provisions will be necessary and the
appliance and ventilation system manufacturer’s
instructions should be followed.
Ventilation of other rooms
or spaces
1.8 If an appliance is room-sealed but takes its
combustion air from another space in the building
(such as the roof void) or if a flue has a permanent
opening to another space in the building (such as
where it feeds a secondary flue in the roof void),
that space should have ventilation openings
directly to outside. Where the roof-space is to
be used as a source of air for a combustion
installation serving a dwelling, the dwelling roof
ventilation provisions suggested in Approved
Document C would normally be satisfactory.
1.9 Where flued appliances are supplied with
combustion air through air vents which open into
adjoining rooms or spaces, the adjoining rooms
or spaces should have air vent openings of at
least the same size direct to the outside. Air
vents for flueless appliances, however, should
open directly to the outside air.
Section 1: Provisions which apply generally
to combustion installations

J
18
PROVISIONS WHICH APPLY GENERALLY TO
J COMBUSTION INSTALLATIONS
Diagram 8 General air supply to a combustion appliance
(for sizes see Sections 2, 3 and 4)
O N L I N E V E R S I O NWHICH
O N L I N E V E R S I O NWHICH APPLY
O N L I N E V E R S I O NAPPLY GENERALLY
O N L I N E V E R S I O NGENERALLY TO
O N L I N E V E R S I O NTO
INSTALLATIONSO N L I N E V E R S I O NINSTALLATIONS

J
19
Permanently open air vents
1.10 Permanently open air vents should be
non-adjustable, sized to admit sufficient air for
the purpose intended and positioned where they
are unlikely to become blocked. Ventilators should
be installed so that building occupants are not
provoked into sealing them against draughts or
noise. Ventilation openings should not be made
in fire-resisting walls other than external walls
(although they should not penetrate those parts
of external walls shielding LPG tanks). Air vents
should not be located within a fireplace recess
except on the basis of specialist advice.
1.11 A way of meeting the requirement would be
to size permanently open air vents so that their
equivalent area is sufficient for the appliance(s) to
be installed (taking account where necessary of
obstructions such as grilles and anti-vermin
mesh), and to site them:
a. outside fireplace recesses and beyond the
hearths of open fires so that dust or ash will
not be disturbed by draughts; and
b. in a location unlikely to cause discomfort from
cold draughts.
1.12 Where ventilation is to be provided via a
single proprietary assembly, for example when
it is proposed to use a proprietary ventilator with
integral grilles to bridge a cavity wall, the equivalent
area of the ventilator should be taken as that
declared by the manufacturer having been
measured by the method in BS EN 13141-1:2004.
1.13 Where two or more components are to be
used to provide a non-proprietary assembly, the
assembly should be kept as simple and smooth as
possible. The assembly should be taken to have
an equivalent area equal to that of the component
with the smallest equivalent area in the assembly.
1.14 The equivalent area stated in the ventilator
manufacturer’s literature or marked on the air vent
should be used whenever it is available, as this can
differ considerably from the free area measured at
one end of the air vent. When this is not available
the equivalent area of a simple ventilator with no
internal baffles can be taken as the total
unobstructed cross-sectional area, measured in
the plane where this area is at a minimum and at
right angles to the direction of air flow. For an
airbrick, grille or louvre with apertures no smaller
than 5mm, it will be the aggregate free area of
the individual apertures as shown Diagram 9.
COMBUSTION INSTALLATIONS J
Equivalent
or Free area 1
(a) Ventilator assembled on site from
components
The ventilator area is the smaller of
equivalent area (1 or 2) (as declared
by manufacturer), free area (1 or 2)
(as measured in (b)) or the duct area.
Equivalent
or Free area 2
Diagram 9 Ventilator free areas
INSTALLATIONS O N L I N E V E R S I O NINSTALLATIONS

J
20
1.15 Grilles or meshes protecting air vents from
the entry of animals or birds should have aperture
dimensions no smaller than 5mm.
1.16 Discomfort from cold draughts can be
avoided by supplying air directly to appliances,
locating vents close to appliances (for example
by using floor vents), by drawing air from
intermediate spaces such as hallways or by
ensuring good mixing of incoming cold air by
placing external air vents close to ceilings (see
Diagrams 10 and 11). In noisy areas it may be
necessary to install noise-attenuated ventilators
to limit the entry of noise into the building.
Transfer or connecting ventilation should be at
low level to reduce the transfer of smoke in the
event of a fire and otherwise meet the guidance
given in Approved Document B.
1.17 Buildings may have air-tight membranes in
their floors to isolate them from the ground below.
Ventilation ducts or vents installed to supply air
to combustion appliances should not penetrate
these membranes in a way that will render them
ineffective. Such membranes (including radon-
proof membranes) are described in BRE Report
BR 414 (2001) and BRE Report BR 211 (2007),
which give guidance when service penetrations
are necessary.
Provisions complying with both
Part F and Part J
1.18 Rooms or spaces intended to contain
open-flued combustion appliances may need
permanent ventilation to comply with Part J and
adjustable ventilation to comply with Part F.
Permanently open air vents for combustion
appliances can be accepted in place of some or
all of the adjustable background ventilation for
health, dependent upon opening area and
location. However adjustable vents installed to
meet the requirements of Part F cannot be used
as substitutes for the ventilation openings
needed to comply with Part J unless they are
fixed permanently open.
1.19 Rooms or spaces intended to contain
flueless appliances may need: permanent
ventilation and purge ventilation (such as openable
windows) to comply with Part J; and adjustable
ventilation and rapid ventilation to comply with
Part F. Permanent ventilation provisions to
comply with Part J may be acceptable in place of
adjustable ventilation provisions for Part F
subject to the limitations described in Paragraph
1.18. Openable elements installed for the rapid
ventilation of rooms and other provisions made
for the rapid ventilation of kitchens, in order to
comply with Part F, may be acceptable in place
of openable elements for the rapid ventilation of
rooms or spaces containing flueless appliances.
Well-
Well-
Diagram 10 Location of permanent air vent openings, some examples

J
21
Interaction of mechanical extract
ventilation and open-flued
combustion appliances
1.20 Extract fans lower the pressure in a building,
which can cause the spillage of combustion
products from open-flued appliances. This can
occur even if the appliance and the fan are in
different rooms. Ceiling fans produce air currents
and hence local depressurisation, which can also
cause the spillage of flue gases from open-flued
appliances or from solid fuel open fires. In buildings
where it is intended to install open-flued combustion
appliances and extract fans, the combustion
appliances should be able to operate safely whether
or not the fans are running. A way of showing
compliance in these circumstances would be to
follow the installation guidance below, and to
show by tests that combustion appliances
operate safely whether or not fans are running.
a. For gas appliances: where a kitchen contains
an open-flued appliance, the extract rate of
the kitchen extract fan should not exceed
20 litres/second (72m³/hour).
b. For oil appliances: where a room contains an
open-flued appliance the extract rate should
be limited to 40 litres/second for an appliance
with a pressure jet burner and 20 litres/second
for an appliance with a vaporising burner.
c. For solid fuel appliances: avoid installing
extract ventilation in the same room. An
open-flued appliance in a kitchen may satisfy
the requirements of Part F through passive
stack ventilation. Refer to Approved
Document F. If mechanical extraction is
unavoidable then seek specialist advice to
ensure safe operation of the appliance.
d. For commercial and industrial installations,
specialist advice may be necessary regarding
the possible need for the interlocking of gas
heaters and any mechanical ventilation
systems.
e. When fans are used to extract radon from
below a building follow the guidance in BRE
Good Building Guide GBG 25.
1.21 A suitable test would be to check for
spillage when appliances are subjected to the
greatest possible depressurisation. A prerequisite
for this condition is that all external doors,
windows and other adjustable ventilators to
outside are closed. The depressurisation at the
appliance will depend on the particular combination
of fans in operation (fans in the room containing
the appliance and fans elsewhere in the building)
and the pattern of open internal doors, hatches
etc. which is established at the time of the test
(when fans should be on their maximum useable
setting), and the specific combination causing
the greatest depressurisation at the appliance
depends upon the circumstances in each case.
Several tests (which should include a test with
the door leading into the room of installation
closed and all fans in that room switched on) may
therefore be necessary to demonstrate the safe
operation of the appliance with reasonable
certainty. The effect of ceiling fans should be
checked during the tests.
1.22 The presence of some fans may be obvious,
such as those on view in kitchens, but others
may be less obvious: fans installed in domestic
appliances such as tumble dryers and fans fitted
to other open-flued combustion appliances can
also contribute to depressurisation. In addition,
fans may also be provided to draw radon gas
from the ground below a building (see Paragraph
1.17).
Diagram 11 Provision of permanent air vent openings in a solid floor

J
22
1.23 The appliance manufacturer’s installation
instructions may describe a suitable spillage
test for gas appliances but the procedure in
BS 5440-1:2008 can be used. For oil-fired
appliances the effects of fans can be checked
and, where spillage or flue draught interference is
identified, it may be necessary to add additional
ventilation to the room or space. A flue draught
interference test for oil-fired appliances is
described in OFTEC Technical Books 2, 4 and 5.
Provision of flues
1.24 Appliances other than flueless appliances
should incorporate or be connected to suitable
flues which discharge to the outside air.
1.25 This Approved Document provides
guidance on how to meet the requirements in
terms of constructing a flue or chimney, where
each flue serves one appliance only. Flues
designed to serve more than one appliance can
meet the requirements by following the guidance
in BS 5410-1:1997 for oil- and BS 5440-1:2008
for gas-fired systems. However, each solid fuel
appliance should have its own flue.
Condensates in flues
1.26 Chimneys and flues should provide
satisfactory control of water condensation.
Ways of providing satisfactory control include:
a. for chimneys that do not serve condensing
appliances, by insulating flues so that flue
gases do not condense in normal operation
b. for chimneys that do serve condensing
appliances:
i. by using lining components that are
impervious to condensates and suitably
resistant to corrosion (BS EN 1443:2003
‘W’ designation) and by making
appropriate provisions for draining,
avoiding ledges, crevices, etc
ii. making provisions for the disposal of
condensate from condensing appliances.
Construction of masonry
chimneys
1.27 New masonry chimneys should be
constructed with flue liners and masonry suitable
for the intended application. Ways of meeting the
requirement would be to use bricks, medium-
weight concrete blocks or stone (with wall
thicknesses as given in Section 2, 3 or 4
according to the intended fuel) with suitable
mortar joints for the masonry and suitably
supported and caulked liners. Liners suitable for
solid fuel appliances (and generally suitable for
other fuels) could be:
a. liners whose performance is at least equal to
that corresponding to the designation T400
N2 D 3 G, as described in BS EN 1443:2003,
such as:
i. clay flue liners with rebates or sockets for
jointing meeting the requirements for
Class A1 N2 or Class A1 N1 as described
in BS EN 1457:2009; or
ii. concrete flue liners meeting the
requirements for the classification Type
A1, Type A2, Type B1 or Type B2 as
described in BS EN 1857:2003; or
iii. other products that meet the criteria in a).
1.28 Liners should be installed in accordance
with their manufacturer’s instructions. Appropriate
components should be selected to form the flue
without cutting and to keep joints to a minimum.
Bends and offsets should be formed only with
matching factory-made components. Liners need
to be placed with the sockets or rebate ends
uppermost to contain moisture and other
condensates in the flue. Joints should be sealed
with fire cement, refractory mortar or installed in
accordance with their manufacturer’s instructions.
Spaces between the lining and the surrounding
masonry should not be filled with ordinary mortar.
In the absence of liner manufacturer’s instructions,
the space could be filled with a weak insulating
concrete such as mixtures of:
a. one part ordinary Portland cement to 20 parts
suitable lightweight expanded clay aggregate,
minimally wetted; or
b. one part ordinary Portland cement to 6 parts
Vermiculite; or
c. one part ordinary Portland cement to 10 parts
Perlite.
Construction of flueblock
chimneys
1.29 Flueblock chimneys should be constructed
of factory-made components suitable for the
intended application installed in accordance with
the manufacturer’s instructions. Ways of meeting
the requirement for solid fuel appliances (and
generally suitable for other fuels) include using:
a. flueblocks whose performance is at least
equal to that corresponding to the
designation T400 N2 D 3 G, as described
in BS EN 1443:2003, such as:
i. clay flueblocks at least meeting the
requirements for Class FB1 N2 as
described in BS EN 1806:2006
ii. other products that meet the criteria in a).
b. blocks suitable for the purpose lined in
accordance with Paragraph 1.27.
1.30 Joints should be sealed in accordance
with the flueblock manufacturer’s instructions.
Bends and offsets should be formed only with
matching factory-made components.
J COMBUSTION INSTALLATIONSO N L I N E V E R S I O NWHICH

J
23
Material change of use
1.31 Where a building is to be altered for
different use (e.g. it is being converted into flats)
the fire resistance of walls of existing masonry
chimneys may need to be improved as shown in
Diagram 12.
Connecting fluepipes
1.32 Satisfactory components for constructing
connecting fluepipes include:
a. cast iron fluepipes complying with BS
41:1973 (1998)
b. metal flue pipes appropriately designated in
accordance with BS EN1856-2:2004 to suit
the appliance and types of fuels to be burnt
– refer to detailed guidance in Sections 2, 3
and 4.
c. vitreous enamelled steel pipe complying with
BS 6999:1989 (1996)
d. other fluepipes having the necessary
performance designation for use with the
intended appliance.
1.33 Fluepipes with spigot and socket joints
should be fitted with the socket facing upwards
to contain moisture and other condensates in
the flue. Joints should be made gas-tight. A
satisfactory way of achieving this would be to
use proprietary jointing accessories or, where
appropriate, by packing joints with non-
combustible rope and fire cement.
Repair of flues
1.34 It is important to the health and safety
of building occupants that renovations,
refurbishments or repairs to flue liners should
result in flues that comply with the requirements
of J2 to J5. The test procedures referred to in
paragraph 1.55 and in Appendix E can be used
to check this.
1.35 Flues are controlled services as defined in
Regulation 2 of the Building Regulations, that is
to say they are services in relation to which Part J
of Schedule 1 imposes requirements. If renovation,
refurbishment or repair amounts to or involves
the provision of a new or replacement flue liner, it
is ‘building work’ within the meaning of Regulation
3 of the Building Regulations. ‘Building work’ and
must not be undertaken without prior notification
to the local authority. Examples of work that
would need to be notified include:
a. relining work comprising the creation of new
flue walls by the insertion of new linings such
as rigid or flexible prefabricated components
Diagram 12 Material change of use: fire protection of chimneys passing
through other dwellings
COMBUSTION INSTALLATIONS JO N L I N E V E R S I O NWHICH

J
24
b. a cast in situ liner that significantly alters the
flue’s internal dimensions.
Anyone in doubt about whether or not any
renovation, refurbishment or repair work involving
a flue is notifiable ‘building work’, could consult
the building control department of their local
authority, or an approved inspector.
Re-use of existing flues
1.36 Where it is proposed to bring a flue in an
existing chimney back into use or to re-use a flue
with a different type or rating of appliance, the
flue and the chimney should be checked and, if
necessary, altered to ensure that they satisfy the
requirements for the proposed use. A way of
checking before and/or after remedial work
would be to test the flue using the procedures
in Appendix E.
1.37 A way of refurbishing defective flues
would be to line them using the materials and
components described in Sections 2, 3, and 4
dependent upon the type of combustion
appliance proposed. Before relining flues, they
should be swept to remove deposits.
1.38 A flue may also need to be lined to reduce
the flue area to suit the intended appliance.
Oversize flues can be unsafe.
1.39 If a chimney has been relined in the past
using a metal lining system and the appliance is
being replaced, the metal liner should also be
replaced unless the metal liner can be proven to
be recently installed and can be seen to be in
good condition.
Use of flexible metal flue liners for
the relining of chimneys
1.40 A way of relining a chimney would be to use
a flexible metal flue liner, appropriately designated
in accordance with BS EN1856-2:2004 to suit the
appliance, fuel and flue gas characteristics.
Flexible flue liners should be used only to reline a
chimney and should not be used as the primary
liner of a new chimney. They can be used to
connect gas back boilers to chimneys where the
appliance is located in a fireplace recess.
Use of plastic fluepipe systems
1.41 A way of using plastic flue systems and
liners would be to use a plastic flue, appropriately
designated in accordance with BS EN 14471:2005
to suite the appliance, fuel and flue characteristics.
Plastic fluepipe systems can be acceptable in
some cases, for example with condensing boiler
installations, where the fluepipes are supplied by
or specified by the appliance manufacturer as
being suitable for purpose.
Factory-made metal chimneys
1.42 Ways of meeting the requirements when
proposing factory-made metal chimneys include:
a. using component systems appropriately
designated in accordance with BS EN1856-
1:2003 to suit the appliance and types of fuels
to be burnt and installing them in accordance
with the relevant recommendations of
BS EN 15287-1:2007;
b. for gas and for oil appliances where flue
temperatures will not normally exceed 250°C,
using twin-walled component systems (and,
for gas, single-walled component systems)
appropriately designated in accordance with
BS EN1856-1:2003 to suit the appliance and
types of fuels to be burnt and installing gas
appliances in accordance with BS 5440-
1:2008;
c. using any other chimney system that is
suitable for the intended purpose and
installed in accordance with the relevant
recommendations in BS EN 15287-1:2007 or
BS 5440-1:2008, as appropriate to the type
of appliance being installed.
1.43 Where a factory-made metal chimney
passes through a wall, sleeves should be provided
to prevent damage to the flue or building through
thermal expansion. To facilitate the checking of
gas-tightness, joints between chimney sections
should not be concealed within ceiling joist
spaces or within the thicknesses of walls without
proper access being provided (see paragraph 1.47).
1.44 When providing a factory-made metal
chimney, provision should be made to withdraw
the appliance without the need to dismantle the
chimney.
1.45 Factory-made metal chimneys should be
kept a suitable distance away from combustible
materials. Ways of meeting the requirement for
chimneys designated to BS EN 1856-1:2003
comprise:
a. locating the chimney not less than distance
‘xx’ from combustible material, where ‘xx’ is
defined in BS EN 1856-1:2003 as shown in
Diagram 13;
b. where a chimney passes through a cupboard,
storage space or roof space, providing a
guard placed no closer to the outer wall of
the chimney than the distance in a) above.
1.46 Where a factory-made metal chimney
penetrates a fire compartment wall or floor, it
must not breach the fire separation requirements
of Part B. See Approved Document B for more
guidance but the requirements may be met by:
a. using a factory-made metal chimney of the
appropriate level of fire resistance installed in
accordance with BS EN 1856-1:2003 Annex
NA; or
b. casing the chimney in non-combustible
material giving at least half the fire resistance
recommended for the fire compartment wall
or floor.

J
25
Concealed flues
1.47 Where a flue is routed within a void,
appropriate means of access at strategic
locations should be provided to allow the
following aspects to be visually checked and
confirmed. This is necessary both when an
appliance is first installed and subsequently
when the appliance is serviced:
• the flue is continuous throughout its length
• all joints appear correctly assembled and are
appropriately sealed
• the flue is adequately supported throughout
its length
• any required gradient of fall back to the boiler
(required to recover the condensate produced
as part of the combustion process) and any
other required drain points have been
provided.
Means of access for flues needs to be sufficiently
sized and positioned to allow a visual inspection
to be undertaken of the flue, particularly at any
joints in the flue. It is not intended that the means
of access should be sized to allow full physical
access to the flue system. Diagram 14 shows an
acceptable approach for a flue in an ceiling void.
Flues should not pass through another dwelling
since access for inspection may not always be
available to that dwelling and chimney system
running through it. Flues may pass through
communal areas including purpose-designed
ducts where inspection access is provided.
Any ‘means of access’ should not impair any
fire, thermal or acoustic requirements of the
Building Regulations. Refer to the relevant
guidance in Approved Documents B, L and E.
Where necessary, inspection panels or hatches
should be fitted with resilient seals and provide
the similar standards of fire, thermal and acoustic
isolation to the surrounding structure.
Access hatches should be at least 300mm x
300mm or larger where necessary to allow
sufficient access to the void to look along the
length of the flue. Digram 14 shows an
acceptable approach to providing access to a
horizontal flue located within a ceiling void.
Distance xx
distance (xxmm) as
designated to BS EN 1856-1
xx
xx
Diagram 13 The separation of combustible material from a factory-made metal
chimney designated to BS EN 1856-1:2003

J
26
Configuration of natural draught
flues serving open-flued
appliances
1.48 Flue systems should offer least resistance
to the passage of flue gases by minimising
changes in direction or horizontal length. A way
of meeting the requirement would be to build
flues so that they are straight and vertical except
for the connections to combustion appliances
with rear outlets where the horizontal section
should not exceed 150mm. Where bends are
essential, they should be angled at no more than
45° to the vertical.
1.49 Provisions should be made to enable flues
to be swept and inspected. A way of making
reasonable provision would be to limit the
number of changes of direction between the
combustion appliance outlet and the flue outlet
to not more than four (each up to 45°), with not
more than two of these being between an
intended point of access for sweeping and either
another point of access for sweeping or the flue
outlet. (90° factory-made bends, elbows or Tee
pieces in fluepipes may be treated as being equal
to two 45° bends (see Diagram 15)).
Flue terminal Flue terminal
External wall
Internalwall
Inspection hatchxx
x
Inspection hatch
Concealed
flue connection
All voids containing concealed flues should have at least one inspection hatch
measuring at least 300mm square.
No flue joint within the void should be more than 1.5m distant from the edge of
the nearest inspection hatch, i.e. dimension x in the diagram should be less than 1.5m.
Where possible inspection hatches should be located at changes of direction.
Where this is not possible then bends should be viewable from both directions.
Accessible
flue connection
Boiler A
Boiler B
Any intervening joints
to be visible within
1.5m of an inspection
hatch
Any intervening joints
to be visible within
1.5m of an inspection
hatch
Inspection hatch
Inspection hatch
+
xx
Diagram 14 Example locations of access panels for concealed horizontal flues

J
27
Inspection and cleaning openings
in flues
1.50 A flue should not have openings into more
than one room or space except for the purposes of:
a. inspection or cleaning; or
b. fitting an explosion door, draught break,
draught stabiliser or draught diverter.
1.51 Openings for inspection and cleaning
should be formed using purpose factory-made
components compatible with the flue system,
having an access cover that has the same level
of gas-tightness as the flue system and an equal
level of thermal insulation. Openings for cleaning
the flue should allow easy passage of the
sweeping brush. Covers should also be non-
combustible except where fitted to a combustible
fluepipe (such as a plastic fluepipe). After the
appliance has been installed, it should be
possible to sweep the whole flue.
Flues discharging at low level
near boundaries
1.52 Flues discharging at low level near
boundaries should do so at positions where the
building owner will always be able to ensure safe
flue gas dispersal. A way of achieving this where
owners of adjacent land could build up to the
boundary would be to adopt the suggestions in
Diagram 34 or 41, as relevant.
Dry lining around fireplace
openings
1.53 Where a decorative treatment, such as
a fireplace surround, masonry cladding or dry
lining, is provided around a fireplace opening,
any gaps that could allow flue gases to escape
from the fireplace opening into the void behind
the decorative treatment should be sealed to
prevent such leakage. The sealing material
should be capable of remaining in place despite
any relative movement between the decorative
treatment and the fireplace recess.
Condition of combustion
installations at completion
1.54 Responsibility for achieving compliance
with the requirements of Part J rests with the
person carrying out the work. That ‘person’ may
be, e.g., a specialist firm directly engaged by a
private client or it may be a developer or main
contractor who has carried out work subject to
Part J or engaged a sub-contractor to carry it out.
In order to document the steps taken to achieve
compliance with the requirements, a report
should be drawn up showing that materials and
components appropriate to the intended
application have been used and that flues have
passed appropriate tests. A suggested checklist
for such a report is given at Appendix A and
guidance on testing is given at Appendix E. Other
forms of report may be acceptable. Specialist
firms should provide the report to the client,
developer or main contractor, who may be asked
for documentation by the Building Control Body.
Diagram 15 Bends in flues

28
1.55 Flues should be checked at completion
to show that they are free from obstructions,
satisfactorily gas-tight and constructed with
materials and components of sizes which suit
the intended application. Where the building
work includes the installation of a combustion
appliance, tests should cover fluepipes and [the
gas-tightness of] joints between fluepipes and
combustion appliance outlets. A spillage test to
check for compliance with J2 should be carried
out with the appliance under fire, as part of
the process of commissioning to check for
compliance with Part L, and (in relevant cases)
as required by the Gas Safety (Installation and
Use) Regulations.
1.56 Hearths should be constructed with
materials and components of sizes to suit the
intended application and should show the area
where combustible materials should not intrude.
Notice plates for hearths and flues
(Requirement J5)
1.57 Where a hearth, fireplace (including a flue
box), flue or chimney is provided or extended
(including cases where a flue is provided as part
of the refurbishment work), information essential
to the correct application and use of these
facilities should be permanently posted in the
building. A way of meeting this requirement
would be to provide a notice plate as shown in
Diagram 16 conveying the following information:
a. the location of the hearth, fireplace
(or flue box) or the location of the beginning
of the flue;
b. the category of the flue and generic types of
appliances that can be safely accommodated;
c. the type and size of the flue (or its liner if it
has been relined) and the manufacturer’s
name;
d. the installation date.
1.58 Notice plates should be robust, indelibly
marked and securely fixed in an unobtrusive but
obvious position within the building such as:
a. next to the electricity consumer unit; or
b. next to the chimney or hearth described; or
c. next to the water supply stop-cock.
1.59 For chimney products whose performance
characteristics have been assessed in
accordance with a European Standard (EN) and
which are supplied or marked with a designation,
the installer may optionally include this
designation on the label as shown in Diagram 16.
Access to combustion appliances
for maintenance
1.60 There should be a permanent means of
safe access to appliances for maintenance. Roof
space installations of gas-fired appliances should
comply with the requirements of BS 6798:2009.
Diagram 16 Example notice plate for hearths and flues

J
29
Air supply to appliances
2.1 A way of meeting the requirement would
be to adopt the general guidance given in
Section 1, beginning at Paragraph 1.2, in
conjunction with the guidance below.
2.2 Any room or space containing an
appliance should have a permanent air vent
opening of at least the size shown in Table 1. For
appliances designed to burn a range of different
solid fuels the air supply should be designed to
accommodate burning the fuel that produces the
highest heating output.
2.3 Some manufacturers may specify even
larger areas of permanently open air vents or
omit to specify a rated output (for example in the
case of a cooker). In these cases, manufacturers’
installation instructions should be followed
subject to any minimum ventilation provisions
of this Approved Document.
Table 1 Air supply to solid fuel appliances
Type of appliance Type and amount of ventilation (1)
Open appliance, such as an open fire with
no throat, e.g. a fire under a canopy as in
Diagram 23.
Permanently open air vent(s) with a total equivalent area of at least 50% of the cross
sectional area of the flue.
Open appliance, such as an open fire with a
throat as in Diagrams 22 and 29.
Permanently open air vent(s) with a total equivalent area of at least 50% of the throat
opening area. (2)
Other appliance, such as a stove, cooker or
boiler, with a flue draught stabiliser.
Permanently open vents as below:
If design air permeability >5.0m3
/(h.m2
) then
300mm2
/kW for first 5kW of appliance rated output
850mm2
/kW for balance of appliance rated output
If design air permeability 5.0m3
/(h.m2
) then
850mm2
/kW of appliance rated output (4)
Other appliance, such as a stove, cooker or
boiler, with no flue draught stabiliser.
Permanently open vents as below:
If design air permeability >5.0m3
/(h.m2
) then
550mm2
/kW of appliance rated output above 5kW
If design air permeability 5.0m3
/(h.m2
) then
550mm2
per kW of appliance rated output (4)
Notes:
1. Equivalent area is as measured according to the method in BS EN 13141-1:2004 or estimated according to paragraph 1.14. Divide the area given in
mm2
by 100 to find the corresponding area in cm2
2. For simple open fires as depicted in Diagram 29, the requirement can be met with room ventilation areas as follows:
Nominal fire size (fireplace opening size) 500mm 450mm 400mm 350mm
Total equivalent area of permanently open air vents 20,500mm2
18,500mm2
16,500mm2
14,500mm2
3. Example: an appliance with a flue draught stabiliser and a rated output of 7kW would require an equivalent area of: [5 x 300] + [2 x 850] = 3200mm2
4. It is
unlikely that a dwelling constructed prior to 2008 will have an air permeability of less than 5.0m3
/(h.m2
) at 50 Pa unless extensive measures have
been taken to improve air-tightness. See Appendix F.
Size of flues
2.4 Fluepipes should have the same diameter
or equivalent cross-sectional area as that of the
appliance flue outlet and should not be smaller
than the size recommended by the appliance
manufacturer.
2.5 Flues should be at least the size shown in
Table 2 relevant to the particular appliance, and
not less than the size of the appliance flue outlet
or that recommended by the appliance
manufacturer.
Section 2: Additional provisions for
appliances burning solid fuel (including solid
biofuel) with a rated output up to 50kW

J
30
2.6 For multi-fuel appliances, the flue should
be sized to accommodate burning the fuel that
requires the largest flue.
Table 2 Size of flues in chimneys
Installation (1) Minimum flue size
Fireplace with an opening of up to 500mm x 550mm 200mm diameter or rectangular/square flues having the same cross-
sectional area and a minimum dimension not less than 175mm
Fireplace with an opening in excess of 500mm x
550mm or a fireplace exposed on two or more sides
See paragraph 2.7. If rectangular/square flues are used the minimum
dimension should be not less than 200mm
Closed appliance of up to 20kW rated output which:
a) burns smokeless or low-volatiles fuel (2)
or
b) is an appliance which meets the requirements of
the Clean Air Act when burning an appropriate
bituminous coal (3)
or
c) is an appliance which meets the requirements of
the Clean Air Act when burning wood (3)
125mm diameter or rectangular/square flues having the same cross-
sectional area and a minimum dimension not less than 100mm for straight
flues or 125mm for flues with bends or offsets
Pellet burner or pellet boiler which meets the
requirements of the Clean Air Act (3)
125mm diameter
This may be reduced to no less than 100mm when permitted by the
appliance manufacturer and supported by calculation according to BS EN
13384-1:2002. This calculation can be applied to an individual installation
or manufacturers can provide precalculated designs.
Other closed appliance of up to 30kW rated output
burning any fuel
Closed appliance of above 30kW and up to 50kW rated
output burning any fuel
Notes:
1. Closed appliances include cookers, stoves, room heaters and boilers.
2. Fuels such as bituminous coal, untreated wood or compressed paper are not smokeless or low-volatiles fuels.
3. These appliances are known as ‘exempted fireplaces’.
ADDITIONAL PROVISIONS FOR APPLIANCES BURNING SOLID
J FUEL WITH A RATED OUTPUT UP TO 50kW
2.7 For fireplaces with openings larger than
500mm x 550mm or fireplaces exposed on two
or more sides (such as a fireplace under a canopy
or open on both sides of a central chimney
breast) a way of showing compliance would be to
provide a flue with a cross-sectional area equal
to 15 per cent of the total face area of the
fireplace opening(s) (see Appendix B). However,
specialist advice should be sought when
proposing to construct flues having an area of:
a. more than 15 per cent of the total face area of
the fireplace openings; or
b. more than 120,000mm² (0.12m²).
Height of flues
2.8 Flues should be high enough to ensure
sufficient draught to clear the products of
combustion. The height necessary for this will
depend upon the type of the appliance, the
height of the building, the type of flue and the
number of bends in it, and an assessment of
local wind patterns. However, a minimum flue
height of 4.5m could be satisfactory if the
guidance in Paragraphs 2.10 to 2.12 is adopted.
As an alternative approach, the calculation
procedure within BS EN 13384-1:2005 can be
used as the basis for deciding whether a chimney
design will provide sufficient draught.
2.9 The height of a flue serving an open fire is
measured vertically from the highest point at
which air can enter the fireplace to the level at
which the flue discharges into the outside air. The
highest point of air entry into the fireplace could
be the top of the fireplace opening or, for a fire
under a canopy, the bottom of the canopy. The
height of a flue serving a closed appliance is
measured vertically from the appliance outlet.
Outlets from flues
2.10 The outlet from a flue should be above
the roof of the building in a position where the
products of combustion can discharge freely and
will not present a fire hazard, whatever the wind
conditions.
2.11 Flue outlet positions which can meet the
requirements in common circumstances are
shown in Diagram 17. The chimney heights and/
or separations shown may need to be increased
in particular cases where wind exposure,
surrounding tall buildings, high trees or high
ground could have adverse effects on flue draught.
O N L I N E V E R S I O NPROVISIONS
O N L I N E V E R S I O NPROVISIONS FOR
O N L I N E V E R S I O NFOR APPLIANCES
O N L I N E V E R S I O NAPPLIANCES BURNING
O N L I N E V E R S I O NBURNING
RATEDO N L I N E V E R S I O NRATED OUTPUTO N L I N E V E R S I O NOUTPUT UPO N L I N E V E R S I O NUP TOO N L I N E V E R S I O NTO 50kWO N L I N E V E R S I O N50kW

J
31
FUEL WITH A RATED OUTPUT UP TO 50kW J
Regulated building
Adjacent building
Point where flue passes through
weather surface (Notes 1, 2) Clearances to flue outlet
A At or within 600mm of the
ridge
At least 600mm above the
ridge
B Elsewhere on a roof
(whether pitched or flat)
At least 2300mm horizontally
from the nearest point on the
weather surface and:
a) at least 1000mm above the
highest point of intersection
of the chimney and the
weather surface; or
b) at least as high as the
ridge.
C Below (on a pitched roof) or
within 2300mm horizontally
to an openable rooflight,
dormer window or other
opening (Note 3)
At least 1000mm above the
top of the opening.
D Within 2300mm of an
adjoining or adjacent
building, whether or not
beyond the boundary
(Note 3)
At least 600mm above any
part of the adjacent building
within 2300mm.
Notes
1) The weather surface is the building external surface, such as
its roof, tiles or external walls.
2) A flat roof has a pitch less than 10°.
3) The clearances given for A or B, as appropriate, will also apply.
4) A vertical flue fixed to an outside wall should be treated as
equivalent to an inside flue emerging at the nearest edge of the
roof.
Diagram 17 Flue outlet positions for solid fuel appliances
RATEDO N L I N E V E R S I O NRATED OUTPUTO N L I N E V E R S I O NOUTPUT UPO N L I N E V E R S I O NUP TOO N L I N E V E R S I O NTO 50kW O N L I N E V E R S I O N50kW

J
32
2.12 A way of meeting the requirements where
flues discharge on or in close proximity to roofs
with surfaces which are readily ignitable, such as
where roofs are covered in thatch or shingles,
would be to increase the clearances to flue
outlets to those shown in Diagram 18.
Note: Thatched roofs can sometimes be vulnerable
to spontaneous combustion caused by heat
transferred from flues building up in thick layers of
thatch in contact with the chimney. To reduce the
risk it is recommended that rigid twin-walled
insulated metal flue liners be used within a
ventilated (top and bottom) masonry chimney void
provided they are adequately supported and not in
direct contact with the masonry. Non-metallic
chimneys and cast in-situ flue liners can also be
used provided the heat transfer to the thatch is
assessed in relation to the depth of thatch and risk
of spontaneous combustion.
Spark arrestors are not generally recommended
as they can be difficult to maintain and may
increase the risk of flue blockage and flue fires.
Further information and recommendations are
contained in Hetas Information Paper 1/007
Chimneys in Thatched Properties.
Connecting fluepipes
2.13 For connecting fluepipes a way of meeting
the requirements would be to follow the general
guidance in Paragraphs 1.32 and 1.33.
Location and shielding of
connecting fluepipes
2.14 Connecting fluepipes should be used only
to connect appliances to their chimneys. They
should not pass through any roof space, partition,
internal wall or floor, except to pass directly into
Diagram 18 Flue outlet positions for solid fuel appliances – clearances to easily
ignited roof coverings
(Note: This diagram needs to be read in conjunction with Diagram 17)

J
33
a chimney through either a wall of the chimney
or a floor supporting the chimney. Connecting
fluepipes should also be guarded if they could
be at risk of damage or if the burn hazard they
present to people is not immediately apparent.
2.15 Connecting fluepipes should be located so
as to avoid igniting combustible material. Ways
of meeting the requirement include minimising
horizontal and sloping runs and:
a. following the guidance in Paragraph 1.45
where the connecting fluepipe is a factory-
made metal chimney whose performance is
at least equal to designation T400 N2 D3 G
according to BS EN 1856-1:2003 or BS EN
1856-2:2004, and installed to BS EN 15827-
1; or
b. separation by shielding in accordance with
Diagram 19.
Debris collection space
2.16 Where a chimney cannot be cleaned
through the appliance, a debris collecting space
which is accessible for emptying and suitably
sized opening(s) for cleaning should be provided
at appropriate locations in the chimney.
Masonry and flueblock chimneys
2.17 Masonry chimneys should be built in
accordance with Paragraphs 1.27 and 1.28.
Flueblock chimneys should be built in
accordance with Paragraphs 1.29 and 1.30.
The minimum chimney thickness and distance
to combustibles (xxmm) should be no less than
the manufacturer’s product declaration (Gxx)
based on testing to BS EN 1858:2008 (concrete
flue blocks) or BS EN 1806:2006 (clay/ceramic
flueblocks). Other masonry chimney products
should exceed the minimum thickness indicated
in Diagram 20.
At least
3 ϫ D
Atleast
3
ϫ
D
At least
3 ϫ D
At least
1.5 ϫ D
At least
1.5 ϫ D
At least
1.5 ϫ D
At least
1.5 ϫ D
At least
1.5 ϫ D
Diagram 19 Protecting combustible material from uninsulated fluepipes for solid
fuel appliances

J
34
Separation of combustible
material from fireplaces and
masonry flues
2.18 Combustible material should not be
located where it could be ignited by the heat
dissipating through the walls of fireplaces or
masonry flues. A way of meeting the requirement
would be to follow the guidance in Diagram 21 so
that combustible material is at least:
a. 200mm from the inside surface of a flue or
fireplace recess; or
b. at least xxmm from a flue product with
designated separation distance (Gxx); or
c. 40mm from the outer surface of a masonry
chimney or fireplace recess unless it is a
floorboard, skirting board, dado or picture
rail, mantel-shelf or architrave. Metal fixings
in contact with combustible materials should
be at least 50mm from the inside surface of
a flue.
2.19 A way of meeting the requirements would
be to comply with Paragraphs 1.42 to 1.46 in
Section 1 (but not Paragraph 1.42(b)). The
appropriate designation is given in Table 3.
Lining and relining of flues in
chimneys
2.20 Lining or relining flues may be building
work and, in any case, such work should be
carried out so that the objectives of J2 to J5 are
met (see Paragraphs 1.34 and 1.35). Existing
flues being re-used should be checked as
described in Paragraph 1.36. Ways of meeting
the requirements include the use of:
a. liners whose performance is at least equal to
that corresponding to the designation T400
N2 D3 G, as described in BS EN 1443:2003,
such as:
i. factory-made flue lining systems
manufactured to BS EN 1856-1:2003 or
BS EN 1856-2:2004.
ii. a cast in-situ flue relining system where
the material and installation procedures
are suitable for use with solid fuel burning
appliances and meeting the relevant
requirements of BS EN 1857:2003 +
A1:2008.
iii. other systems which are suitable for use
with solid fuel-burning appliances and
meeting the criteria in (a).
b. liners as described in Paragraph 1.27.
Diagram 20 Wall thicknesses for masonry and flueblock chimneys

J
35
Table 3 Minimum performance
designations for chimney and
fluepipe components for
use with new solid fuel fired
appliances
Appliance
type
Minimum
designation
Fuel type
All solid fuel
appliances
Masonry or flueblock
flue with liner to T400
N2 D3 Gxx
Clay flue blocks
FB1N2
Clay/ceramic liners
B1N2
Concrete liners B2
Factory made metal
chimneys to T400 N2
D3 Gxx
Coal, Smokeless
Fuel, Peat, wood
and other biomass
See paragraph 1.27–1.29 and 1.42
Formation of gathers
2.21 To minimise resistance to the proper
working of flues, tapered gathers should be
provided in fireplaces for open fires. Ways of
achieving these gathers include:
a. using prefabricated gather components built
into a fireplace recess, as shown in Diagram
22(a); or
b. corbelling of masonry as shown in Diagram
22(b); or
c. using a suitable canopy, as shown in Diagram
23; or
d. using a prefabricated appliance chamber
incorporating a gather.
Diagram 21 Minimum separation distances from combustible material in or
near a chimney

J
36
Diagram 22 Construction of fireplace gathers
Diagram 23 Canopy for an open solid fuel fire

J
37
Hearths
2.22 Hearths should be constructed of suitably
robust materials and to appropriate dimensions
such that, in normal use, they prevent combustion
appliances setting fire to the building fabric and
furnishings, and they limit the risk of people being
accidentally burnt. A way of making provision
would be to adopt the guidance in Paragraphs
2.23 to 2.28 and to provide a hearth appropriate
to the temperatures the appliance can create
around it. The hearth should be able to accommodate
the weight of the appliance and its chimney if the
chimney is not independently supported.
2.23 Appliances should stand wholly above:
a. hearths made of non-combustible board/
sheet material or tiles at least 12mm thick, if
the appliance is not to stand in an appliance
recess and has been tested to an applicable
appliance standard to verify that it cannot
cause the temperature of the upper surface
of the hearth to exceed 100°C; or
b. constructional hearths in accordance with the
paragraphs below.
2.24 Constructional hearths should:
a. have plan dimensions as shown in Diagram
24; and
b. be made of solid, non-combustible material,
such as concrete or masonry, at least 125mm
thick, including the thickness of any non-
combustible floor and/or decorative surface.
2.25 Combustible material should not be
placed beneath constructional hearths unless
there is an air-space of at least 50mm between
the underside of the hearth and the combustible
material, or the combustible material is at
least 250mm below the top of the hearth (see
Diagram 25).
Diagram 24 Constructional hearth suitable for a solid fuel appliance (including open fires)
Diagram 25 Constructional hearth suitable for a solid fuel appliance (including open fires)

J
38
2.26 An appliance should be located on a
hearth so that it is surrounded by a surface free
of combustible material as shown in Diagram 26.
This surface may be part of the surface of the
hearth provided in accordance with Paragraph
2.23, or it may be the surface of a superimposed
hearth laid wholly or partly upon a constructional
hearth. The boundary of this surface should be
visually apparent to provide a warning to the
building occupants and to discourage combustible
floor finishes such as carpet from being laid too
close to the appliance. A way of achieving this
would be to provide a change in level.
2.27 Dimensions shown in Diagram 26 may be
reduced to manufacturer’s recommendations for
appliances with surface temperatures not
exceeding 85°C when in normal operation and
where there is no risk of spillage of fuel or ash.
2.28 Combustible material placed on or beside
a constructional hearth should not extend under
a superimposed hearth by more than 25mm or to
closer than 150mm measured horizontally to the
appliance.
2.29 Some ways of making these provisions are
shown in Diagram 27.
Fireplace recesses and
prefabricated appliance chambers
2.30 Fireplaces for open fires need to be
constructed such that they adequately protect
the building fabric from catching fire. A way of
achieving the requirements would be to build:
a. fireplace recesses from masonry or concrete
as shown in Diagram 28; or
b. prefabricated factory-made appliance
chambers using components that are made
of insulating concrete having a density of
between 1200 and 1700 kg/m³ and with the
minimum thickness as shown in Table 4.
Components should be supplied as sets for
assembly and jointing in accordance with the
manufacturer’s instructions.
Diagram 26 Non-combustible hearth surface surrounding a solid fuel appliance

J
39
Diagram 27 Ways of providing hearths

J
40
Table 4 Prefabricated appliance chambers: minimum thickness
Component Minimum thickness (mm)
Base 50
Side section, forming wall on either side of chamber 75
Back section, forming rear of chamber 100
Top slab, lintel or gather, forming top of chamber 100
Fireplace lining components
2.31 A fireplace recess may require protection
from heat if it is to provide a durable setting for
certain appliances such as inset open fires.
Suitable protection would be fireplace lining
components as shown in Diagram 29 or lining
the recess with suitable firebricks.
Walls adjacent to hearths
2.32 Walls that are not part of a fireplace recess
or a prefabricated appliance chamber but are
adjacent to hearths or appliances also need to
protect the building from catching fire. A way of
achieving the requirement is shown in Diagram
30. Thinner material could be used provided it
gives the same overall level of protection as the
solid non-combustible material.
2.33 Clearances shown in Diagram 30 may be
reduced to manufacturer’s recommendations for
appliances with surface temperatures not
exceeding 85°C when in normal operation.
Alternative approach
The requirements may also be met by adopting
the relevant recommendations in the publications
listed below to achieve a level of performance
equivalent to that obtained by following the
guidance in this Approved Document:
a. BS EN 15287-1:2007 Chimneys. Design,
installation and commissioning of chimneys.
Chimneys for non-room-sealed heating
appliances; and
b. BS 8303:1994 Installation of domestic
heating and cooking appliances burning
solid mineral fuels. Parts 1 to 3.
Diagram 28 Fireplace recesses

J
41
Carbon monoxide alarms
2.34 Where a new or replacement fixed solid
fuel appliance is installed in a dwelling, a carbon
monoxide alarm should be provided in the room
where the appliance is located.
2.35 Carbon monoxide alarms should comply
with BS EN 50291:2001 and be powered by a
battery designed to operate for the working life of
the alarm. The alarm should incorporate a
warning device to alert users when the working
life of the alarm is due to pass. Mains-powered
BS EN 50291 Type A carbon monoxide alarms
with fixed wiring (not plug-in types) may be used
as alternative applications provided they are
fitted with a sensor failure warning device.
2.36 The carbon monoxide alarm should be
located in the same room as the appliance:
a. on the ceiling at least 300mm from any wall
or, if it is located on a wall, as high up as
possible (above any doors and windows) but
not within 150mm of the ceiling; and
b. between 1m and 3m horizontally from the
appliance.
Note: Further guidance on the installation of
carbon monoxide alarms is available in
BS EN 50292:2002 and from manufacturers’
instructions. Provision of an alarm should not be
regarded as a substitute for correct installation
and regular servicing.
Diagram 29 Open fireplaces: throat and fireplace components

J
42
Diagram 30 Wall adjacent to hearths

J
43
Gas Safety (Installation and Use)
Regulations
3.1 All combustion installations must be
accommodated in ways that meet the requirements
of the Building Regulations. However, gas
installations also have to comply with the Gas
Safety (Installation and Use) Regulations, which
require anyone undertaking gas work to be
competent. Any gas engineering business,
whether an employer or self employed, must be a
member of a class of persons approved by the
Health and Safety Executive (HSE). Because of
this, the Building Regulations allow that work
need not be notified to Building Control Bodies
if it solely comprises the installation of a gas
appliance and it is to be undertaken by a member
of such an approved class of persons. The Gas
Safety (Installation and Use) Regulations cover
the safe installation maintenance and use of gas
fittings, appliances and flues. The following
paragraphs give builders and lay readers an
outline of some of the main requirements of the
Gas Safety (Installation and Use) Regulations, but
for further information reference should be made
to the Health and Safety Commission’s Approved
Code of Practice (see below) or Building Control
Bodies.
3.2 The Gas Safety (Installation and Use)
Regulations require that (a) gas fittings, appliances
and gas storage vessels must be installed only
by a person with the required competence and
(b) any person having control to any extent of gas
work must ensure that the person carrying out
that work has the required competence and (c)
any gas installation businesses, whether an
employer or self-employed, must be a member of
a class of persons approved by the HSE; for the
time being this means they must be registered
with Gas Safe Register.
3.3 Guidance on the individual competency
required for gas work is available from the Sector
Skills Council Energy and Utility (EU) Skills
[http://www.euskills.co.uk/gas]. Persons deemed
competent to carry out gas work are those who
hold a current certificate of competence in the
type of activity to be conducted. Assessment of
competence may be through the S/NVq
qualilification under a nationally accredited
certification scheme or under the Approved Code
of Practice arrangements.
3.4 The Gas Safety (Installation and Use)
Regulations control all aspects of the ways
combustion systems fired by gas (including
natural gas and LPG) are installed, maintained
and used, mainly in domestic and commercial
premises, and the classes of persons who may
undertake gas work. The Regulations may be
amended from time to time and whichever
Regulations are currently in force at the time
an installation is carried out must be complied
with. The advice given below reflects the present
state of the Gas Safety (Installation and Use)
Regulations following the amendments that
came into effect on 31 October 1998.
3.5 The text of the Regulations and guidance
on how to comply with them are contained in the
Health and Safety Executive (HSE) Approved
Code of Practice ‘Safety in the installation and
use of gas systems and appliances’. Important
elements of the Regulations include that:
a. any appliance installed in a room used or
intended to be used as a bath or shower
room must be of the room-sealed type;
b. a gas fire, other gas space heater or gas
water heater of more than 14kW (gross) heat
input (12.7kW (net) heat input) must not be
installed in a room used or intended to be
used as sleeping accommodation unless the
appliance is room sealed;
c. a gas fire, other space heater or gas water
heater of up to 14kW (gross) heat input
(12.7kW (net) heat input) must not be
installed in a room used or intended to be
used as sleeping accommodation unless it
is room sealed or equipped with a device
designed to shut down the appliance before
there is a build-up of a dangerous quantity
of the products of combustion in the room
concerned;
d. the restrictions in (a)–(c) above also apply in
respect of any cupboard or compartment
within the rooms concerned, and to any
cupboard, compartment or space adjacent
to, and with an air vent into, such a room;
e. instantaneous water heaters (installed in any
room) must be room sealed or have fitted a
safety device to shut down the appliance as
in (c) above;
f. precautions must be taken to ensure that all
installation pipework, gas fittings, appliances
and flues are installed safely. When any gas
appliance is installed, checks are required for
ensuring compliance with the Regulations,
including the effectiveness of the flue, the
supply of combustion air, the operating
pressure or heat input (or where necessary
both), and the operation of the appliance to
ensure its safe functioning;
g. any flue must be installed in a safe position
and must be adequate, suitable and effective
for use with the appliance which it serves;
J
Section 3: Additional provisions for gas
burning appliances with a rated input up to
70kW (net)

J
44
h. no alteration is allowed to any premises in
which a gas fitting or gas storage vessel is
fitted which would adversely affect the safety
of that fitting or vessel, causing it no longer to
comply with the Regulations;
i. LPG storage vessels and LPG-fired appliances
fitted with automatic ignition devices or pilot
lights must not be installed in cellars or
basements.
ADDITIONAL PROVISIONS FOR GAS BURNING APPLIANCES
J WITH A RATED INPUT UP TO 70kW (net)
Diagram 31 Types of gas fire
O N L I N E V E R S I O NFOR GAS
O N L I N E V E R S I O NGAS BURNING
O N L I N E V E R S I O NBURNING APPLIANCES
O N L I N E V E R S I O NAPPLIANCES
INPUTO N L I N E V E R S I O NINPUT UPO N L I N E V E R S I O NUP TOO N L I N E V E R S I O NTO 70kWO N L I N E V E R S I O N70kW (net)O N L I N E V E R S I O N(net)

J
45
Gas fires (other than flueless
gas fires)
3.6 These appliances fall into the main
categories shown in Diagram 31 and the building
provisions for accommodating them safely differ
for each type.
3.7 Provided it can be shown to be safe, gas
fires may be installed in fireplaces which have
flues designed to serve solid fuel appliances.
Certain types of gas fire may also be installed in
fireplaces which have flues designed specifically
for gas appliances. The Gas Appliances (Safety)
Regulations 1995 require that particular
combinations of appliance, flue box (where
required) and flue must be selected from those
stated in the manufacturer’s instructions as
having been shown to be safe by a Notified
Body.
Flueless gas appliances
3.8 Flueless appliances should meet the
requirements, including requirement J2. A way of
achieving this would be to follow the guidance on
ventilation provisions for flueless appliances
beginning at Paragraph 3.15.
3.9 A flueless instantaneous water heater
should not be installed in a room or space having
a volume of less than 5 m³.
Air supply to gas fires and
other appliances
be to follow the general guidance given in
Section 1, beginning at Paragraph 1.2, in
conjunction with the guidance below.
Flued Decorative Fuel Effect
(DFE) fires
3.11 Any room or space intended to contain a
DFE fire should have permanently open air vents
as described in (a) or (b) below, unless the
installation is in accordance with Paragraph 3.12:
a. for a DFE fire in a fireplace recess with a
throat, the air vent equivalent area should be
at least 10,000mm² (100cm²)
b. for a DFE fire in a fireplace with no throat,
such as a fire under a canopy, the air vent
should be sized in accordance with Section 2
of this Approved Document, as if the room
were intended to contain a solid fuel fire
(see Table 1).
3.12 In dwellings with an air permeability
greater than 5.0 m3
/hr/m2
(see Appendix F),
permanently open air vents may not be necessary
for DFE fires with ratings not exceeding 7kW (net)
that have a flue gas clearance rate (without
spilling) not exceeding 70 m3
/hour.
Flued appliances other than
decorative fuel effect fires
3.13 These appliances include inset live fuel
effect (ILFE) fires, radiant convector fires and
boilers, in both room-sealed and open-flued
variants.
be to follow the guidance in Diagram 32. An
example calculation illustrating the use of this
guidance is given in Appendix C.
Air supply to flueless appliances
3.15 For some flueless appliances, it may be
necessary to provide permanently open air vents
and/or make provision for rapid ventilation as
recommended in BS 5440-2:2009 or equivalent,
to comply with Part F as well as Part J of the
Building Regulations. Some ways of meeting the
requirement when installing flueless cookers
(including ovens, grills or hotplates), flueless
water heaters and flueless space heaters are
given in Diagram 33.
3.16 A room containing a gas point intended for
use with a flueless appliance (such as a gas point
for a cooker or a gas point for a space or water
heater, the gas point not being adjacent to a flue)
should have the ventilation provision required for
the installation of that appliance (calculated on
the basis that an appliance with the largest rating
consistent with the table to Diagram 33 could be
installed there).
WITH A RATED INPUT UP TO 70kW (net) JO N L I N E V E R S I O NPROVISIONS
INPUTO N L I N E V E R S I O NINPUT UPO N L I N E V E R S I O NUP TOO N L I N E V E R S I O NTO 70kWO N L I N E V E R S I O N70kW (net) O N L I N E V E R S I O N(net)

J
46
5. In older dwellings with an air permeability which is more than 5.0m3
/h/m2
the first 7kW(net) can be ignored.
Diagram 32 Free areas of permanently open air vents for gas appliance installations
(other than decorative fuel effect fires or flueless appliances)

J
47
Size of natural draught flues for
open-flued appliances
3.17 Where builders wish to provide (or
refurbish) flues for gas appliances but do not
intend to supply the appliances, a way of
showing compliance would be to size flues in
accordance with Table 5.
3.18 If an existing flue is to be used it should be
checked in accordance with Paragraph 1.36.
3.19 For appliances that are CE marked as
compliant with the Gas Appliances (Safety)
Regulations, flues should be sized in accordance
with the manufacturer’s installation instructions.
3.20 Connecting fluepipes should be the same
size in terms of diameter and/or equivalent
cross-sectional area as the appliance flue outlet.
The chimney flue should have at least the same
cross-sectional area as that of the appliance
flue outlet.
WITH A RATED INPUT UP TO 70kW (net) J
8
Notes:
1. The permanent ventilation provisions listed in this table are additional to the openable elements or (for kitchens only)
extract ventilation in accordance with Approved Document F.
2. Divide the area given above in mm2
by 100 to find the corresponding area in cm2
.
3. An internal space here means one which communicates with several other rooms or spaces. An example would be a
hallway or landing.
4. For LPG fired space heaters conforming to BS EN 449:2002+A1:2007, follow the guidance in BS 5440-2:2009.
5. No permanently open vent is needed if the room or space has a door direct to outside.
6. Example: for a space heater in a lounge measuring 4m x 4m x 2.4m (= 38.4m3
), the appliance rated input should not
exceed 38.4 x 0.045 = 1.73kW (net).
7. Example: a hallway containing a space heater with a rated input of 7kW (net) should have a permanently open vent with
equivalent area of: 10,000 + 2750 x (7 – 5.4) = 14,400mm2
.
8. No permanent opening required if the room has a door that opens directly to outside.
Diagram 33 Ventilation for flueless gas appliances

J
48
Table 5 Size of flues for gas-fired appliances
Intended installation Minimum flue size
Radiant / Convector gas fire New flue:
Circular 125mm diameter
Rectangular 16,500mm2
cross-sectional area with a
minimum dimension of 90mm
Existing flue:
Circular 125mm diameter
Rectangular 12,000mm2
cross-sectional area with a
minimum dimension of 63mm
ILFE fire or DFE fire within a fireplace opening up to
500mm x 550mm
DFE fire installed in a fireplace with an opening in
excess of 500mm x 550mm
Circular or rectangular Minimum flue dimension of 175mm (1)

Calculate in accordance with paragraph 2.7 in Section 2
Note:
1. Some ILFE and DFE appliances require a circular flue of at least 125mm diameter.
Height of natural draught flues
for open-flued appliances
3.21 Flues should be high enough to ensure
sufficient draught to safely clear the products of
combustion. The height necessary for this will
depend upon the type of appliance, the building
height, the type of flue and the number of bends
in it, and a careful assessment of local wind
patterns. For appliances that are CE marked as
Regulations, compliance with the manufacturer’s
installation instructions will meet the requirements.
3.22 Where an older appliance that is not CE
marked is to be installed, a way of showing
compliance if it has manufacturer’s installation
instructions would be:
a. for decorative fuel effect fires, to follow the
guidance in BS 5871-3:2001 2005; or
b. for appliances other than decorative fuel
effect fires, to follow the calculation
procedures in BS 5440-1:2008.
Outlets from flues
3.23 Outlets from flues should be so situated
externally as to allow the dispersal of products of
combustion and, if a balanced flue, the intake of
air. A way of meeting this requirement would be
to locate flue outlets as shown in Diagram 34 and
Diagram 35.
Note: The plume of wet flue products from
condensing boilers, positioned in accordance
with the safety distances set out in Diagram 34,
can sometimes be considered a nuisance for
neighbouring properties. Whilst this nuisance is
not considered to be within the scope of building
regulations, such installations could be
considered as a ‘Statutory Nuisance’ as set out
in the Environmental Protection Act. As such
installers may wish to adopt the guidance in
Chapter 6 of the Guide to Condensing Boiler
Installation Assessment Procedure for Dwellings
Care may also need to be taken to locate flue
outlets away from parts of the building that
may be damaged by frequent wetting.
J WITH A RATED INPUT UP TO 70kW (net)O N L I N E V E R S I O NPROVISIONS

J
49
Diagram 34 Location of outlets from flues serving gas appliances

J
50
Table to Diagram 34 Location of outlets from flues serving gas appliances
Minimum separation distances for terminals in mm
Location Balanced flue Open flue
Natural draught Fanned draught Natural draught Fanned draught
A Below an opening (1) Appliance rated
heat input (net)
300 (3) 300
0–7kW
>7–14kW
>14–32kW
>32kW
300
600
1500
2000
B Above an opening (1) 0–32kW
>32kW
300
600
300 (3) 300
C Horizontally to an opening (1) 0–7kW
>7–14kW
>14kW
300
400
600
300 (3) 300
D Below gutters, soil pipes or
drainpipes
300 75 (3) 75
E Below eaves 300 200 (3) 200
F Below balcony or car port roof 600 200 (3) 200
G From a vertical drainpipe or
soil pipe
300 150 (4) (3) 150
H From an internal or external
corner or to a boundary
alongside the terminal (2)
600 300 (3) 200
I Above ground, roof or
balcony level
300 300 (3) 300
J From a surface or a boundary
facing the terminal (2)
600 600 (3) 600
K From a terminal facing
the terminal
600 1200 (3) 1200
L From an opening in the car
port into the building
1200 1200 (3) 1200
M Vertically from a terminal on
the same wall
1200 1500 (3) 1500
N Horizontally from a terminal
on the same wall
300 300 (3) 300
P From a structure on the roof N/A N/A 1500mm if a
ridge terminal. For
any other terminal,
as given in
BS 5440-1:2008
N/A
q Above the highest point of
intersection with the roof
N/A Site in
accordance with
manufacturer’s
instructions
Site in
accordance with
BS 5440-1:2008
150
Notes:
1. An opening here means an openable element, such as an openable window, or a fixed opening such as an air vent. However, in addition, the outlet
should not be nearer than 150mm (fanned draught) or 300mm (natural draught) to an opening into the building fabric formed for the purpose of
accommodating a built-in element, such as a window frame.
2. Boundary as defined in paragraph 0.4 (4). Smaller separations to the boundary may be acceptable for appliances that have been shown to operate
safely with such separations from surfaces adjacent to or opposite the flue outlet.
3. Should not be used.
4. This dimension may be reduced to 75mm for appliances of up to 5kW input (net).
N/A means not applicable.

J
51
3.24 Flue outlets should be protected where
flues are at significant risk of blockage. Guidance
on meeting this requirement is given below.
3.25 Flues serving natural draught open-flued
appliances should be fitted with outlet terminals if
the flue diameter is no greater than 170mm.
Suitable terminals include those appropriately
designated in accordance with BS EN 1856-
1:2003, and conforming to BS EN 13502:2002.
The risk of blockage of flues of more than
170mm diameter should be assessed in the light
of local conditions. In areas where nests of
squirrels or jackdaws are likely, the fitting of a
protective cage designed for solid fuel use and
having a mesh size no larger than 25mm (but
no smaller than 6mm) may be an acceptable
provision if the total free area of its outlet
openings is at least twice the cross-sectional
area of the flue.
3.26 A flue outlet should be protected with a
guard if persons could come into contact with it
or if it could be damaged. If a flue outlet is in a
vulnerable position, such as where the flue
discharges within reach from the ground, or a
balcony, veranda or a window, it should be
designed to prevent the entry of any matter that
could obstruct the flow of flue gases.
Provision of flues
3.27 Satisfactory provision of chimneys and
fluepipes for gas appliances may be achieved by:
a. following the guidance on the selection of
components and the manner of their
installation as given in Paragraphs 3.28 to
3.35 and the references to Section 1; or (if
the intended appliance is new and of
known type)
or (if the intended appliance is new and of
known type):
b. i) using factory-made components that
achieve a performance at least equal to
that corresponding to the designation
given in Table 6 for the intended appliance
type when tested to an appropriate
European chimney standard (BS EN); and
ii) installing these components in accordance
with the guidance in Paragraphs 3.28 to
3.35 and Section 1, as relevant, and in
accordance with the appliance manufacturer’s
and component manufacturer’s
installation instructions.
fluepipe components for use
with new gas appliances
Appliance type Minimum
designation
(see notes)
Boiler: open-flued Natural draught
Fanned draught
Condensing
T250 N2 D 1 O
T250 P2 D 1 O
T140 P2 W 1 O
Boiler: room-sealed Natural draught
Fanned draught
Condensing
T250 N2 D 1 O
T250 P2 D 1 O
T140 P2 W 1 O
Gas fire –
radiant/convector, ILFE or DFE

T250 N2 D 1 O
Air heater Natural draught
Fanned draught
SE – duct
T250 N2 D 1 O
T250 P2 D 1 O
T250 N2 D 1 O
Notes:
1. The designation of chimney products is described in Appendix G.
The BS EN for the product will specify its full designation and
marking requirements.
2. These are default designations. Where the appliance manufacturer’s
installation instructions specify a higher designation, this should
be complied with.
Diagram 35 Location of outlets near roof windows from flues serving gas appliances

52
Connecting fluepipe components
3.28 Satisfactory components for connecting
fluepipes include:
a. any of the options in Paragraph 1.32; or
b. sheet metal fluepipes as described in
BS EN 1856-2:2004; or
c. fibre cement pipes as described in
BS EN 1857:2003+A1:2008; or
d. any other material or component that has
been certified as suitable for this purpose.
Masonry chimneys
3.29 Masonry chimneys should be built in
accordance with Paragraphs 1.27 and 1.28 in
Section 1.
Flueblock chimneys
3.30 Chimneys can be constructed from
factory-made flueblock systems primarily
designed for solid fuel, as described in
Paragraphs 1.29 and 1.30 in Section 1. They can
also be constructed from factory-made flueblock
systems comprising straight blocks, recess units,
lintel blocks, offset blocks, transfer blocks and
jointing materials complying with:
a. BS EN 1858-1:2003 for concrete flueblocks of
at least class D2; or
b. BS EN 1806:2006 for clay/ceramic flueblocks
with a performance class of at least FB4 N2.
3.31 Flueblock chimneys should be installed
with sealed joints in accordance with the
flueblock manufacturer’s installation instructions.
Where bends or offsets are required, these
should be formed using matching factory-made
components. Flueblocks which are not intended
to be bonded into surrounding masonry should
be supported and restrained in accordance with
the manufacturer’s installation instructions.
3.32 Chimneys for gas appliances may be
constructed using systems described in
Paragraphs 1.42 to 1.46 in Section 1. Factory-
made metal chimneys should be guarded if they
could be at risk of damage or the burn hazard
they present to people is not immediately apparent.
Location and shielding of flues
3.33 Combustible materials in the building
fabric should be protected from the heat
dissipation from flues so that they are not at risk
of catching fire. A way of meeting the requirement
would be to follow the guidance in Table 6.
3.34 Where a fluepipe or chimney penetrates a
fire compartment wall or floor, it must not breach
the fire separation requirements of Part B. See
Approved Document B for more guidance.
Table 7 Protecting buildings from
hot flues
Flue within Protection measures
Connecting fluepipe Flues should be at least 25mm
from any combustible material
(measured from the outer surface
of the flue wall, or the outer
surface of the inner wall in the
case of multi-walled products).
Where passing through a
combustible wall, floor or roof
(other than a compartment wall,
floor or roof) this separation can
be achieved by a non-combustible
sleeve enclosing the fluepipe or
chimney with a 25mm air-space
to the relevant flue wall. (The air-
space could be wholly or partially
filled with non-combustible
insulating material).
Factory-made
chimney appropriately
designated to BS EN
1856-1:2003
Factory-made
chimney appropriately
designated to BS EN
1856-1:2003 and BS
EN 1856-2:2004
Install in accordance with
Paragraph 1.45 of this Approved
Document with minimum
separation distances according
to flue designation.
Masonry chimney Provide at least 25mm of
masonry between flues and
any combustible material.
Flueblock chimney Provide flueblock walls at least
25mm thick.
3.35 Connecting fluepipes and factory-made
chimneys should also be guarded if they could
be at risk of damage or if they present a burn
hazard to people that is not immediately apparent
Relining of flues in chimneys
carried out so that the objectives of requirements
J2 to J5 are met (see Paragraphs 1.34 and 1.35).
Existing flues being re-used should be checked
as described in Paragraph 1.36. For flue liners
serving gas appliances, ways of meeting the
requirements include the use of:
a. liners as described in Paragraph 1.27;
b. liners as described in Paragraph 2.20;
c. flexible stainless steel liners appropriately
designated to BS EN 1856-1:2003 (refer to
Table 6);
d. other systems suitable for the purpose.
3.37 Flexible metal flue liners should be
installed in one complete length without joints
within the chimney. Other than for sealing at the
top and the bottom, the space between the
chimney and the liner should be left empty unless
this is contrary to the manufacturer’s instructions.
Double-skin flexible flue liners should be installed
in accordance with the manufacturer’s installation
instructions. BS 715 liners should be installed in
accordance with BS 5440-1:2008.

J
53
Debris collection space
for chimneys
3.38 A debris collection space should be
provided at the base of a flue unless it is lined, or
constructed of flue blocks, or is a factory-made
metal chimney with a flue box. This can be
achieved by providing a space having a volume
of not less than 12 litres and a depth of at least
250mm below the point where flue gases
discharge into the chimney. The space should
be readily accessible for clearance of debris, for
example by removal of the appliance. For gas
fires of the type illustrated in Diagram 31 (a) and
(b), there should be at least 50mm clearance
between the end of the appliance flue outlet
and any surface.
Bases for back boilers
3.39 Provisions for back boilers should
adequately protect the fabric of the building from
heat. A way of meeting the requirement would
be to stand back boilers on hearths intended
for solid fuel appliances. Alternatively, unless
otherwise stated in the appliance manufacturer’s
instructions, a way of meeting the requirements
would be to stand back boilers on bases
complying with Diagram 36.
Diagram 36 Bases for back boilers (installation using a proprietary back boiler
enclosure shown)

J
54
Hearths
3.40 Appliances should be placed on hearths
unless:
a. they are to be installed so that every part of
any flame or incandescent material will be at
least 225mm above the floor; or
b. the manufacturer’s instructions state that a
hearth is not required.
3.41 Where hearths are required, guidance
on their minimum plan dimensions is given in
Diagrams 37 and 38. Hearths should comprise at
least a (top) layer of non-combustible, non-friable
material not less than 12mm thick. The edges of
hearths should be marked to provide a warning
to the building occupants and to discourage
combustible floor finishes such as carpet from
being laid too close to the appliance. A way of
achieving this would be to provide a change
in level.
Shielding of appliances
3.42 Gas-fired appliances should be located
where accidental contact is unlikely and
surrounded by a non-combustible surface which
provides adequate separation from combustible
materials. For appliances that are CE marked as
Regulations, a way of meeting the requirement
would be to adopt the manufacturer’s instructions.
An alternative approach would be to protect
combustible fabric with:
a. a shield of non-combustible material, such as
insulating board, with a fire-resistant surface; or
b. an air space of at least 75mm (see Diagram 39).
Diagram 37 Hearths for decorative fuel effect (DFE) and inset live fuel effect (ILFE)
fires: minimum plan dimensions of non-combustible surfaces

J
55
the relevant recommendations in the publications
listed below to achieve an equivalent level of
performance to that obtained by following the
guidance in this Approved Document:
BS 5440 Installation and maintenance of flues
and ventilation for gas appliances of rated input
not exceeding 70kW net (1st, 2nd and 3rd family
gases), Part 1:2008 Specification for installation
and maintenance of flues; Part 2:2009
Specification for installation and maintenance
of ventilation for gas appliances.
BS 5546:2000 Specification for installation of
hot water supplies for domestic purposes,
using gas-fired appliances of rated input not
exceeding 70kW.
BS 5864:2004 Specification for installation in
domestic premises of gas-fired ducted-air
heaters of rated input not exceeding 60kW.
BS 5871 Specification for installation of gas fires,
convector heaters, fire/back boilers and
decorative fuel effect gas appliances, Part 1:2005
Gas fires, convector heaters and fire/back boilers
and heating stoves (1st, 2nd and 3rd family
gases); Part 2:2005 Inset live fuel effect gas fires
of heat input not exceeding 15kW and fire/back
boilers (2nd and 3rd family gases); Part 3:2005
Decorative fuel effect gas appliances of heat input
not exceeding 20kW (2nd and 3rd family gases).
domestic gas cooking appliances (1st, 2nd and
3rd family gases).
gas-fired catering appliances for use in all types
of catering establishments (2nd and 3rd family
gases).
gas-fired boilers of rated input not exceeding
70kW net.
Diagram 38 Hearths for other appliances: plan dimension of non-combustible surfaces
Diagram 39 Shielding of appliances

J
56
Scope
4.1 This guidance is relevant to combustion
installations designed to burn oils meeting the
specifications for Class C2 (Kerosene) and Class
D (Gas oil) given in BS 2869:2006 or equivalent,
liquid biofuel conforming to EN 14213:2003 and
blends of mineral oil and liquid biofuel.
Appliances fitted in bathrooms
and shower rooms
4.2 Open-flued oil-fired appliances should
not be installed in rooms such as bathrooms and
bedrooms where there is an increased risk of
carbon monoxide poisoning. Where locating
combustion appliances in such rooms cannot
be avoided, a way of meeting the requirements
would be to provide room-sealed appliances.
Air supply to appliances
be to adopt the general guidance given in
Section 1, starting at Paragraph 1.2, and to
provide permanently open air vents as shown in
Diagram 40 in rooms or spaces containing
appliances. An example calculation illustrating
the use of this guidance is given in Appendix D.
Where manufacturers’ installation instructions
require greater areas of permanently open air
vents than those shown in Diagram 40, the
manufacturers’ advice should be followed.
Size of flues (other than balanced
flues and flues designed to
discharge through or adjacent
to walls)
4.4 Flues should be sized to suit the intended
appliance such that they ensure adequate
discharge velocity to prevent flow reversal
problems but do not impose excessive flow
resistances. A way of meeting the requirements
would be to use:
a. connecting fluepipes of the same size as the
appliance flue outlet; and
b. flues in chimneys of the same cross-sectional
area as the appliance flue outlet.
When constructing masonry or flueblock
chimneys, a way of doing this would be to:
i. make the flue the same size as the
appliance flue outlet; or
ii. make the flue larger and of a size that
would allow the later insertion of a
suitable flexible flue liner matching the
appliance to be installed.
4.5 Larger flues may need to be provided
where appliance manufacturers’ installation
instructions demand this.
Outlets from flues and flue heights
4.6 The outlet from a flue should be so
situated externally as to ensure: the correct
operation of a natural draught flue; the intake of
air if a balanced flue; and dispersal of the
products of combustion.
4.7 A way of meeting the requirement could
be to follow the guidance in Diagram 41. The
separations given in the Table to Diagram 41 are
minimum values that may have to be increased
where there is a risk that local factors such as
wind patterns could disrupt the operation of the
flue or where a natural draught flue would not be
tall enough to clear the products of combustion
of an open-flued appliance. For flues in proximity
to roof windows the minimum separation
distances identified in Diagram 35 should be
applied.
Note: The plume of wet flue products from
condensing boilers, positioned in accordance
with the safety distances set out in Diagram 41,
can sometimes be considered a nuisance for
neighbouring properties. Whilst this nuisance is
not considered to be within the scope of building
regulations, such installations could be
considered as a ‘Statutory Nuisance’ as set out
in the Environmental Protection Act. As such,
installers may wish to adopt the guidance in
Chapter 6 of the Guide to Condensing Boiler
Installation Assessment Procedure for Dwellings.
Care may also need to be taken to locate flue
outlets away from parts of the building that
may be damaged by frequent wetting.
4.8 Flue outlets should be protected with
terminal guards if persons could come into
contact with them or if they could be damaged.
If a flue outlet is in a vulnerable position, such as
where the flue discharges at a point within reach
of the ground, balcony, veranda or a window, it
should be designed to prevent the entry of any
matter that could obstruct the flow.

J
Section 4: Additional provisions for oil burning
appliances with a rated output up to 45kW

J
57
ADDITIONAL PROVISIONS FOR OIL BURNING APPLIANCES
WITH A RATED OUTPUT UP TO 45kW J
5. In older dwellings with an air permeability which is more than 5.0m3
/hr/m2
the first 5kW(net) can be ignored.
Notes:
-
Diagram 40 Free areas of permanently open air vents for oil-fired
appliance installations
O N L I N E V E R S I O NFOR OIL
O N L I N E V E R S I O NOIL BURNING
OUTPUTO N L I N E V E R S I O NOUTPUT UPO N L I N E V E R S I O NUP TOO N L I N E V E R S I O NTO 45kW O N L I N E V E R S I O N45kW

J
58
Table to Diagram 41 Location of outlets from flues serving oil-fired appliances
Minimum separation distances for terminals in mm
Location of outlet (1) Appliance with
pressure jet burner
Appliance with
vaporising burner
A Below an opening (2, 3) 600 Should not be used
B Horizontally to an opening (2, 3) 600 Should not be used
C Below a plastic/painted gutter, drainage pipe or eaves if combustible material
protected (4)
75 Should not be used
D Below a balcony or a plastic/painted gutter, drainage pipe or eaves without
protection to combustible material
E From vertical sanitary pipework 300 Should not be used
F From an external or internal corner or from a surface or boundary alongside
the terminal
G Above ground or balcony level 300 Should not be used
H From a surface or boundary facing the terminal 600 Should not be used
J From a terminal facing the terminal 1200 Should not be used
K Vertically from a terminal on the same wall 1500 Should not be used
L Horizontally from a terminal on the same wall 750 Should not be used
M Above the highest point of an intersection with the roof 600 (6) 1000 (5)
N From a vertical structure to the side of the terminal 750 (6) 2300
O Above a vertical structure which is less than 750mm (pressure jet burner) or
2300mm (vaporising burner) horizontally from the side of the terminal
600 (6) 1000 (5)
P From a ridge terminal to a vertical structure on the roof 1500 Should not be used
Notes:
1. Terminals should only be positioned on walls where appliances have been approved for such configurations when tested in accordance with
BS EN 303-1:1999 or OFTEC standards OFS A100 or OFS A101.
2. An opening means an openable element, such as an openable window, or a permanent opening such as a permanently open air vent.
3. Notwithstanding the dimensions above, a terminal should be at least 300mm from combustible material, e.g. a window frame.
4. A way of providing protection of combustible material would be to fit a heat shield at least 750mm wide.
5. Where a terminal is used with a vaporising burner, the terminal should be at least 2300mm horizontally from the roof.
6. Outlets for vertical balanced flues in locations M, N and O should be in accordance with manufacturer’s instructions.
WITH A RATED OUTPUT UP TO 45kW
Diagram 41 Location of outlets from flues serving oil-fired appliances
OUTPUTO N L I N E V E R S I O NOUTPUT UPO N L I N E V E R S I O NUP TOO N L I N E V E R S I O NTO 45kWO N L I N E V E R S I O N45kW

J
59
Flues for oil-fired appliances:
flue gas temperature
fluepipes depends upon the flue gas temperature
to be expected in normal service and separate
guidance is given in this Approved Document
according to whether the proposed installation
will have a flue gas temperature more than or less
than 250°C as measured by a suitable method
such as those in OFTEC Standards A100 or
A101. Suitable chimney systems may then be
selected based on their performance designation
having been tested in accordance with the
relevant European standard.
4.10 Flue gas temperatures depend upon
appliance types and the age of their design.
Modern boilers bearing the CE mark, indicating
compliance with the Boiler (Efficiency)
Regulations (1993), normally have flue gas
temperatures not exceeding 250°C. Condensing
oil-fired appliances will normally produce flue gas
temperatures well below 100°C. Information for
individual appliances should be sought from the
manufacturer’s installation instructions, from the
manufacturers themselves or from OFTEC.
Where this is not available, flues should be
constructed for an assumed flue gas temperature
greater than 250°C.
Provisions for flue gas
temperatures in excess of 250°C
4.11 A way of making satisfactory provision for
oil appliances in these cases would be to follow
the guidance given in Sections 1 and 2 for
connecting fluepipes and masonry or flueblock
chimneys or to provide a factory-made metal
chimney in accordance with Paragraphs 1.42 to
1.46 in Section 1 (but not Paragraph 1.42(b)).
However, other products may be acceptable if
they have been certified for this purpose.
Provisions for flue gas
temperatures not exceeding 250°C
fluepipes for oil appliances in these cases may
be achieved by:
a. following the guidance on the selection of
components and the manner of their
installation as given in Paragraphs 4.13 to
4.20 and the references to Section 1 or
(if the intended appliance is new and of
known type);
b. i) using factory-made components that
achieve a performance at least equal to
that corresponding to the designation
given in Table 8 (for the intended appliance
type) when tested to an appropriate
European chimney standard (BS EN); and
ii) installing these components in accordance
with the guidance in Paragraphs 4.13 to
4.20 and Section 1, as relevant, and in
accordance with the appliance manufacturer’s
and component manufacturer’s
installation instructions.
fluepipe components for use with
new oil-fired appliances with flue
gas temperature less than 250ºC
Appliance type Minimum
designation
Fuel type
Condensing boiler,
including combination
boiler, range cooker,
range cooker/boiler –
with pressure-jet burners
T120 N2 W1 O Class C2 oil
(kerosene)
Liquid biofuel
conforming to
EN 14213:2003
Condensing boiler,
T160 N2 W2 O Class D oil
(heating oil)
Non-condensing boiler,
T250 N2 D1 O Class C2 oil
(kerosene)
Liquid biofuel
conforming to
EN 14213:2003
Non-condensing boiler,
T250 N2 D2 O Class D oil
(heating oil)
Cooker and room heater
– with vaporising burner
T160 N2 D1 O Class C2 oil
(kerosene)
Cooker and room heater
– with vaporising burner
T250 N2 D2 O Class D oil
(heating oil)
Notes:
1. The designation of chimney products is described in Appendix G.
The BS EN for the product will specify its full designation and
marking requirements.
2. These are default designations. Where the appliance
manufacturer’s installation instructions specify a higher
designation, this should be complied with.
3. Refer to the appliance manufacturer regarding the suitability of the
appliance and flue system for use with oil / bio-liquid blends.
Connecting fluepipe components
4.13 Connecting fluepipes can be constructed
using the following components:
a. any of the options listed in Paragraph 1.32; or
b. sheet metal fluepipes as described in BS EN
1856-2:2004; or
c. fibre cement pipes as described in BS EN
1857:2003+A1:2008; or
d. any other component that has been certified
as suitable for this purpose.
WITH A RATED OUTPUT UP TO 45kW JO N L I N E V E R S I O NPROVISIONS

J
60
Masonry chimneys
4.14 Masonry chimneys can be built in
accordance with Paragraphs 1.27 and 1.28 in
Section 1.
Flueblock chimneys
4.15 Chimneys can be constructed from
factory-made flueblock systems primarily
designed for solid fuel, as described in
Paragraphs 1.29 and 1.30 in Section 1. They can
also be constructed from factory-made flueblock
systems comprising straight blocks, recess units,
lintel blocks, offset blocks, transfer blocks and
jointing materials complying with:
a. BS EN 1858:2003 for concrete flueblocks; or
b. BS EN 1806:2006 for clay/ceramic flueblocks,
with a performance at least equal to the
designation given in Table 8 for the intended
appliance type.
4.16 Flueblock chimneys should be installed
with sealed joints in accordance with the
flueblock manufacturer’s installation instructions.
Where bends or offsets are required, these
should be formed using matching factory-made
components. Flueblocks which are not intended
to be bonded into surrounding masonry should
be supported and restrained in accordance with
the manufacturer’s installation instructions.
4.17 Chimneys for oil-fired appliances can be
constructed using the systems described in
Paragraphs 1.42 to 1.46 in Section 1.
Location and shielding of flues
4.18 A way of protecting the building fabric
from the heat dissipation from flues, where flue
gas temperatures are not expected to exceed
250°C, would be to follow the guidance in Table 9.
4.19 Where a fluepipe or chimney penetrates a
fire compartment wall or floor, it must not breach
the fire separation requirements of Part B. See
Approved Document B for more guidance.
4.20 Fluepipes and factory-made chimneys
should also be guarded if they could be at risk of
damage or if they present a hazard to people that
is not immediately apparent such as when they
traverse intermediate floors out of sight of the
appliance.
Table 9 Protecting buildings from hot
flues for flue gas temperatures
not more than 250ºC
Flue within: Protection measures
Connecting fluepipe
Factory-made
chimney designated in
accordance with BS EN
1856-1:2003
Flues should be at least 25mm
from any combustible material
(measured from the outer surface
of the flue wall, or the outer
surface of the inner wall in the
case of multi-walled products).
Where passing through a
combustible wall, floor or roof
(other than a compartment wall
floor or roof) this separation can
be achieved by a non-combustible
sleeve enclosing the fluepipe or
chimney with a 25mm air-space
to the relevant flue wall. (The
air-space could be wholly or
partially filled with non-
combustible insulating material.)
Factory-made
chimney designated in
accordance with BS EN
1856-1:2003 and BS
EN 1856-2:2004
Install in accordance with
Paragraph 1.45 of this Approved
Document with minimum
separation distances according
to flue designation.
Masonry chimney Provide at least 25mm of
masonry between flues and
any combustible material.
Flueblock chimney Provide flueblock walls at least
25mm thick.
Flue assemblies
for room-sealed
appliances
a) flues passing through
combustible walls should
be surrounded by insulating
material at least 50mm thick.
b) provide a clearance of at least
50mm from the edge of the flue
outlet to any combustible wall
cladding.
Relining of flues in chimneys
carried out so that the objectives of requirements
J2 to J5 are met (see Paragraphs 1.34 and 1.35).
For flue liners serving oil appliances, ways of
meeting the requirements include the use of:
a. linings suitable for use if the flue gas
temperature can be expected to exceed
250°C such as:
i. liners as described in Paragraph 1.27;
ii. liners as described in Paragraph 2.20;
iii. flexible stainless steel liners designated in
accordance with BS EN 1858:2008;
iv. other systems which have been certified
as suitable for this purpose.
WITH A RATED OUTPUT UP TO 45kWO N L I N E V E R S I O NPROVISIONS

J
61
b. linings suitable for use if the flue gas
temperature is unlikely to exceed 250°C
such as:
i. any of the linings described in (a) above;
ii. other systems which have been certified
as suitable for this purpose;
iii. (if the appliance is new and of known
type) flue lining systems that have a
performance at least equal to that
corresponding to the designation given in
Table 8 for the intended appliance type.
4.22 Flexible metal flue liners should be
installed in one complete length without joints
within the chimney. Other than for sealing at the
top and the bottom, the space between the
chimney and the liner should be left empty unless
this is contrary to the manufacturer’s instructions.
Double-skin flexible flue liners should be installed
in accordance with the manufacturer’s installation
instructions. Liners should be installed in
accordance with BS EN 15827-1:2007.
Flues for appliances burning
Class D oil
4.23 Flues which may be expected to serve
appliances burning Class D oil should be made
of materials which are resistant to acids of
sulphur, i.e. minimum flue designation ‘D2’
for non-condensing appliances or ‘W2’ for
condensing appliances, according to the
designation system in BS EN 1443:2003 and
related flue standards.
Hearths for oil-fired appliances
4.24 Hearths are needed to prevent the building
catching fire and, whilst it is not a health and
safety provision, it is customary to top them with
a tray for collecting spilled fuel.
4.25 If the operation of an appliance is unlikely
to cause the temperature of the floor below it to
exceed 100°C, as shown using an appropriate
test procedure such as those in OFTEC Standards
A 100 and A 101, special measures may be
unnecessary beyond the provision of a rigid,
imperforate, and non-absorbent sheet of non-
combustible material such as a steel tray. This may
be provided as an integral part of the appliance.
4.26 If the appliance could cause the temperature
of the floor below it to exceed 100°C, a more
substantial hearth is required. A way of meeting
the requirement would be to provide a hearth of
solid non-combustible material at least 125mm
thick (which may include the thickness of any
non-combustible floor) with plan dimensions not
less than those shown in Diagram 24 in Section
2. It should have no combustible material below
it unless there is an air-space of at least 50mm
between the material and the underside of the
hearth, or there is a distance of at least 250mm
between the material and the top of the hearth
(see Diagram 25 in Section 2).
4.27 To provide a region around the appliance
which is free of any combustible material, the
appliance should not be placed closer to the
edges of the hearth nor closer to any combustible
material which is laid over the hearth than the
distances shown in Diagram 42. The perimeter
of this safe region should be marked to provide
a warning to the building occupants and to
discourage combustible floor finishes such as
carpet from being laid too close to the appliance.
A way of achieving this would be to provide a
change in level.
Shielding of oil-fired appliances
4.28 Combustible materials adjacent to oil-fired
appliances may need protection from the effects
of heat. Special measures may be unnecessary
if the materials will not be subjected to
temperatures in excess of 100°C, but otherwise
a way of meeting the requirement would be to
protect combustible fabric with:
a. a shield of non-combustible material, such as
insulating board with fire-resistant surface; or
b. an air-space of at least 75mm (see Diagram
39 in Section 3).
4.29 Appliances having surface temperatures
during normal operation of no more than 100°C
would not normally require shielding.
the relevant recommendations in the publication
listed below to achieve an equivalent level of
performance to that obtained by following the
guidance in this Approved Document: BS 5410-
1:1997 Code of practice for oil firing. Installations
up to 45kW output capacity for space heating
and hot water supply purposes.
WITH A RATED OUTPUT UP TO 45kW JO N L I N E V E R S I O NPROVISIONS

J
62
Diagram 42 Location of an oil-fired appliance in relation to its hearth.
Minimum dimensions of the heat-resistant material in the hearth and
the clear zone of non-combustible surface
WITH A RATED OUTPUT UP TO 45kWO N L I N E V E R S I O NPROVISIONS

J
63
Section 5: Provisions for liquid fuel storage
and supply
J
Performance
5.1 In the Secretary of State’s view
requirements J6 and J7 will be met if:
a. oil and LPG fuel storage installations
including the pipework connecting them to
the combustion appliances in the buildings
they serve are located and constructed so
that they are reasonably protected from fires
which may occur in buildings or beyond
boundaries;
b. oil storage tanks, their ancillary equipment
and the pipework connecting them to
combustion appliances in buildings used
wholly or mainly for private dwellings:
i. are reasonably resistant to physical
damage and corrosion and are designed
and installed so as to minimise the risk
of oil escaping during the filling or
maintenance of the tank; and
ii. incorporate secondary containment when
there is a significant risk of pollution; and
iii. are labelled with information on how to
respond to a leak.
Heating oil storage installations
5.2 Guidance is given in this Approved
Document on ways of meeting requirements J6
and J7 when proposing to construct oil storage
systems with above-ground or semi-buried tanks
of 3500 litres capacity or less, used exclusively
for heating oil. Heating oils comprise Class C2 oil
(kerosene) or Class D oil (gas oil) as specified in
BS 2869:1998, liquid biofuel conforming to EN
14213:2003 and blends of mineral oil and liquid
biofuel. A way of meeting requirements J6 and
J7 for such installations would be to follow the
relevant recommendations in BS 5410-1:1997,
whilst also adopting the guidance in paragraphs
5.4 to 5.12.
5.3 Requirement J7 does not apply to oil
storage systems where the capacity of the tank
exceeds 3500 litres, or where the tank is fully
buried or where the building served is not wholly
or mainly used as one or more private dwellings.
However, requirement J6 applies to oil storage
systems serving buildings of all descriptions,
where the capacity of the tank exceeds 90 litres,
with no upper capacity limit on application, and
including cases where the tank is buried. For
tanks with capacities in excess of 3500 litres,
advice on ways of complying with requirements
J6 and any other fire precautions legislation may
be sought from the Fire Authority. In England
tanks serving buildings which are not wholly or
mainly used as private dwellings are likely to be
subject to the Control of Pollution (Oil Storage)
(England) Regulations 2001 (see paragraph 5.7).
Protective measures against fire
5.4 A way of achieving compliance with
requirement J6 would be to adopt the guidance
given in Table 10, which also offers advice on
reducing the risk of fuel storage system fires
igniting buildings and to make provision against
the installation becoming overgrown. This can be
achieved with a hard surface beneath the tank
such as concrete, or paving slabs at least 42mm
thick, extending out at least 300mm beyond the
perimeter of the tank (or its external skin if it is of
the integrally bunded type).
Table 10 Fire protection for oil
storage tanks
Location of tank Protection usually satisfactory
Within a building Locate tanks in a place of special fire
hazard which should be directly
ventilated to outside. Without prejudice
to the need for compliance with all the
requirements in Schedule 1, the need to
comply with Part B should particularly
be taken into account.
Less than 1800mm
from any part of a
building
a) Make building walls imperforate (1)
within 1800mm of tanks with at least
30 minutes fire resistance (2) to
internal fire and construct eaves.
b) Provide a fire wall (3) between the
tank and any part of the building
within 1800mm of the tank and
construct eaves as in (a) above.
The fire wall should extend at least
300mm higher and wider than the
affected parts of the tank.
Less than 760mm
from a boundary
Provide a fire wall between the tank and
the boundary or a boundary wall having
at least 30 minutes fire resistance to fire
on either side. The fire wall or the
boundary wall should extend at least
300mm higher and wider than the top
and sides of the tank.
At least 1800mm
from the building and
at least 760mm from
a boundary
No further provisions necessary.
Notes:
1. Excluding small openings such as air bricks etc.
2. Fire resistance in terms of insulation, integrity and stability
as determined by testing to the relevant parts of BS 476 or
BS EN 1363 or BS EN 1364.
3. Fire walls are imperforate non-combustible walls or screens,
such as masonry walls or fire-rated composite panel screens.

64
5.5 Fire walls should be built to be stable so
as not to pose a danger to people around them.
A way of achieving this when constructing
masonry walls would be to follow the guidance
on wall thickness in relation to height given in
Your garden walls: Better to be safe than sorry
(See ’Other Publications referred to’).
Oil supply pipe systems:
means of automatic isolation
be to install fuel pipework which is resistant to
the effects of fire and to fit a proprietary fire
valve system in accordance with the relevant
recommendations in BS 5410-1:1997, Sections
8.2 and 8.3.
Provisions where there is a risk
of oil pollution
5.7 The Control of Pollution (Oil Storage)
(England) Regulations 2001 (SI 2001/2954) came
into force on 1 March 2002. They apply to a wide
range of oil storage installations in England, but
they do not apply to the storage of oil on any
premises used wholly or mainly as one or more
private dwellings, if the capacity of the tank is
3500 litres or less. Advice on the construction
of above-ground oil storage tanks that may be
subject to these Regulations is contained in
Above Ground Oil Storage Tanks: PPG2 (2004).
Note: Below ground oil storage is not
recommended where other options are available
as underground tanks are difficult to inspect and
leaks may not be immediately obvious. Some
guidance and further sources of reference are
contained in installation, decommissioning and
removal of underground storage tanks:
PPG27(2002).
5.8 Requirement J6 applies to oil storage
tanks of 3500 litres or less serving combustion
appliances in buildings used wholly or mainly
as private dwellings. In such cases, secondary
containment should be provided where there is a
significant risk of oil pollution. For the purposes
of requirement J6, there is a significant risk of
pollution if the oil storage installation:
a. has a total capacity of more than 2500 litres; or
b. is located within 10m of inland freshwaters
or coastal waters; or
c. is located where spillage could run into an
open drain or to a loose-fitting manhole
cover; or
d. is located within 50m of sources of potable
water, such as wells, bore-holes or springs; or
e. is located where oil spilled from the
installation could reach the waters listed
above by running across hard ground; or
f. is located where tank vent pipe outlets
cannot be seen from the intended filling point.
g. is located within Zone 1 (inner protection
zone) of an Environment Agency Groundwater
Source Protection Zone (SPZ).
Note: The location of SPZs is shown on the
Environment Agency›s Groundwater Sources
map available online at www.environment-
agency.gov.uk/research/library/maps.
5.9 Inland freshwaters include streams, rivers,
reservoirs and lakes, as well as ditches and
ground drainage (including perforated drainage
pipes) that feed into them.
5.10 When secondary containment is
considered necessary, a way of meeting the
requirement would be to:
a. provide an integrally bunded prefabricated
tank; or
b. construct a bund from masonry or concrete
in accordance with the general guidance in
Above Ground Oil Storage Tanks: PPG2
(2004) and the specific advice in Masonry
Bunds for Oil Storage Tanks or Concrete
Bunds for Oil Storage Tanks, as appropriate.
However:
c. where the bund walls are part of the walls of a
chamber or building enclosing the tank, any
door through such walls should be above
bund level; and
d. specialist advice should be sought where
the bund has a structural role as part of a
building.
5.11 Bunds, whether part of prefabricated tank
systems or constructed on site, should have a
capacity of at least 110 per cent of the largest
tank they contain. Integrally bunded oil tanks that
comply with the following standards will meet
this provision:
i. OFS T100 Oil Firing Equipment Standard
– Polyethylene Oil Storage Tanks for
Distillate Fuels (2008);
ii. OFS T100 Oil Firing Equipment Standard
– Steel Oil Storage Tanks and Tank Bunds
for use with Distillate Fuels, Lubrication
Oils and Waste Oils (2008).
5.12 An oil storage installation should carry a
label in a prominent position giving advice on
what to do if an oil spill occurs and the telephone
number of the Environment Agency’s Emergency
Hotline (see Appendix F).
LPG storage installations
5.13 LPG installations are controlled by
legislation enforced by the HSE or their agents.
Factors which determine the amount of building
work necessary for a LPG storage installation to
comply include its capacity, whether tanks are
installed above or below ground and the nature
of the premises they serve. A storage installation
may be shown to comply with the legislation by
constructing it in accordance with an appropriate
industry Code of Practice, prepared in
J PROVISIONS FOR LIqUID FUEL STORAGE AND SUPPLYO N L I N E V E R S I O NROVISIONS FOR LIO N L I N E V E R S I O NROVISIONS FOR LIqO N L I N E V E R S I O NqUID FUEL STORAGE AND SUPPLYO N L I N E V E R S I O NUID FUEL STORAGE AND SUPPLY

65
consultation with the HSE. However, for an
installation of up to 1.1 tonne capacity, whose
tank stands in the open air, following the
guidance in this Approved Document and the
relevant guidance in Approved Document B, will
normally ensure that no further building work is
needed to comply with other legislation.
Tank location and protective
measures
5.14 For LPG storage systems of up to 1.1
tonne capacity, comprising one tank standing in
the open air, a way of meeting the requirement
J6 would be to comply with the relevant
recommendations in the UKLPG Code Of
Practice 1: Bulk LPG Storage at Fixed
Installations Part 1 (2009) and BS 5482-1:2005
(see Appendix F and ‘Other Publications referred
to’) whilst also adopting the following guidance:
5.15 The LPG tank should be installed outdoors
and not within an open pit. The tank should be
adequately separated from buildings, the
boundary and any fixed sources of ignition to
enable safe dispersal in the event of venting or
leaks and in the event of fire to reduce the risk of
fire spreading. A way of meeting the requirements
in normal situations would be to adopt the
separation distances in Table 11 and Diagram 43,
which also offers advice on reducing the risk of
LPG storage fires igniting the building. Drains,
gullies and cellar hatches within the separation
distances should be protected from gas entry.
5.16 Fire walls may be free-standing walls built
between the tank and the building, boundary and
fixed source of ignition (see Diagram 43 (b)) or a
part of the building or a boundary wall belonging
to the property. Where a fire wall is part of the
building or a boundary wall, it should be located
in accordance with Diagram 43(c) and, if part of
the building, constructed in accordance with
Diagram 43(d).
5.17 Suitable fire walls would be imperforate
and of solid masonry, concrete or similar
construction. They should have a fire resistance
(insulation, integrity and stability (REI)) of at least
30 minutes but, if part of the building as shown in
Diagram 43 (d), they should have a fire resistance
(REI) of at least 60 minutes. To ensure good
ventilation, fire walls should not normally be built
on more than one side of a tank.
Table 11 Fire protection for LPG storage tanks (see Diagram 43)
Minimum separation distances from buildings,
boundaries or fixed sources of ignition (metres)
(A)
Capacity of tank not exceeding (tonnes):
(B)
To a tank with no fire wall or
to a tank around a fire wall
(C)
To a tank shielded by
a fire wall
0.25 2.5 0.3
1.1 3 1.5
5.18 A fire wall should be at least as high as the
pressure relief valve. It should extend horizontally
such that the separation specified in Table 11
(Column B) is maintained:
a. when measured around the ends of the fire
wall as shown in Diagram 43(b); or
b. when measured to the ends of the fire wall as
shown in Diagram 43(c), if the fire wall is the
boundary or part of the building.
Location and support of cylinders
5.19 Where an LPG storage installation consists
of a set of cylinders, a way of meeting the
requirements would be to follow the provisions
below and as shown in Diagram 44.
5.20 Provisions should enable cylinders to
stand upright, secured by straps or chains
against a wall outside the building in a well-
ventilated position at ground level, where they are
readily accessible, reasonably protected from
physical damage and where they do not obstruct
exit routes from the building. Satisfactory building
work provisions would be to provide a firm level
base such as concrete at least 50mm thick or
paving slabs bedded on mortar at a location so
that cylinder valves will be:
a. at least 1m horizontally and 300mm vertically
from openings in the building or heat sources
such as flue terminals and tumble-dryer
vents; and
b. at least 2m horizontally from drains without
traps, unsealed gullies or cellar hatches
unless an intervening wall not less than
250mm high is provided.
PROVISIONS FOR LIqUID FUEL STORAGE AND SUPPLY JO N L I N E V E R S I O NROVISIONS FOR LIO N L I N E V E R S I O NROVISIONS FOR LIqO N L I N E V E R S I O NqUID FUEL STORAGE AND SUPPLYO N L I N E V E R S I O NUID FUEL STORAGE AND SUPPLY

66
J PROVISIONS FOR LIqUID FUEL STORAGE AND SUPPLY
Table 11
Column (B)
Table 11
Column (B)
Table 11
Column (C)
Table 11
Column (C)
Table 11
Column (C)
Table 11 Column (B)
(See Diagram (c) above)
Diagram 43 Separation or shielding of liquefied petroleum gas tanks of up to 1.1
tonne capacity from buildings, boundaries and fixed sources of ignition
O N L I N E V E R S I O NROVISIONS FOR LIO N L I N E V E R S I O NROVISIONS FOR LIqO N L I N E V E R S I O NqUID FUEL STORAGE AND SUPPLYO N L I N E V E R S I O NUID FUEL STORAGE AND SUPPLY

67
PROVISIONS FOR LIqUID FUEL STORAGE AND SUPPLY J
LPG pipework (Informative)
5.21 For the puposes of the Gas Safety
(Installation and Use) Regulations 1998 (GSIUR),
where the LPG service pipework runs underground
from the LPG tank to the premises it should be
manufactured of non-corroding material. Pipe
entering the building should be manufactured
from metallic material and the transition joints
between the non-metallic and metallic pipe
should be located outdoors. The pipe should
enter the building above ground and be sleeved.
The sleeve should be continuous through the
external wall and be sealed at the inner wall to
ensure that any escapes of gas are vented to the
outside only. Further guidance is available in
UKLPG Code of Practice 22 and Institution of
Gas Engineers and Managers standard IG/TD/4.
5.22 In respect of installation pipework subject
to the provisions of the GSIUR, Regulation 19(6)
of the GSIUR requires that installation pipework
should not be installed in any shaft, duct or void
which is not adequately ventilated. This is also
applicable to LPG pipework in buildings not
subject to GSIUR. Guidance on the ventilation
of pipe in ducts can be found in BS 8131:1997
Code of Practice for accommodation of building
services in ducts.
Diagram 44 Location of LPG cylinders
O N L I N E V E R S I O NROVISIONS FOR LIO N L I N E V E R S I O NROVISIONS FOR LIqO N L I N E V E R S I O NqUID FUEL STORAGE AND SUPPLYO N L I N E V E R S I O NUID FUEL STORAGE AND SUPPLY

J
68
ExAMPLES: SEE PARAGRAPH 1.55
Hearth, fireplace, flues and chimneys
The checklist can help you to ensure hearths, fireplaces, flues and chimneys are satisfactory. If you have been directly engaged, copies should also
be offered to the client and to the Building Control Body to show what you have done to comply with the requirements of Part J. If you are a sub-
contractor, a copy should be offered to the main contractor.
1. Building address, where work has been carried out ........................................................................................................................................
................................................................................................................................................................................................................................
................................................................................................................................................................................................................................
2. Identification of hearth, fireplace, chimney or flue. Example:
Fireplace in lounge
Example:
Gas fire in rear
addition bedroom
Example:
Small boiler room
3. Firing capability: solid fuel/gas/oil/all. All Gas only Oil only
4. Intended type of appliance.
State type or make. If open fire give finished
fireplace opening dimensions.
Open fire
480 W x 560 H (mm)
Radiant/convector
fire 6kW input
Oil fire boiler 18kW
output (pressure jet)
5. Ventilation provisions for the appliance:
State type and area of permanently open air vents.
2 through wall
ventilators each
10,000mm2
(100cm2
)
Not fitted Vents to outside:
Top 9,900mm2
Bottom 19,800mm2
6. Chimney or flue construction
a) State the type and make and whether new or existing. New. Brick with
clay liners
Existing masonry S.S. prefab to
BS 4543-2
b) Internal flue size (and equivalent height, where
calculated – natural draught gas appliances only).
200mm Ø 125mm Ø (H0=3.3m) 127mm Ø
c) If clay or concrete flue liners used confirm they are
correctly jointed with socket end uppermost and state
joining materials used.
Sockets uppermost
Jointed by fire cement
Not applicable Not applicable
d) If an existing chimney has been refurbished with a new
liner, type or make of liner fitted.
Not applicable
to BS 715
Flexible metal liner Not applicable
e) Details of flue outlet terminal and diagram reference.
Outlet detail: Smith Ltd Louvred pot
200mm Ø
125mm Ø GC1 terminal Maker’s recommended
terminal
Compiles with: As Diagram 17, AD J As BS 5440-1:2008 As Diagram 41, AD J
f) Number and angle of bends. 2 x 45˚ 2 x 45˚ 1 x 90˚ Tee
g) Provision for cleaning and recommended frequency. Sweep annually via
fireplace opening
Annual service by Gas
Safe Register engineer
Sweep annually via base
of Tee and via appliance
7. Hearth, form of construction. New or existing? New. Tiles on concrete
floor. 125mm thick.
As Diagram 25 AD J
Existing hearth for solid
fuel fire, with fender.
New. Solid floor
Min 125mm concrete
above DPM. As Diagram
42, ADJ
8. Inspection and testing after completion
Test carried out by:
Test (Appendix E in AD J) and results
Flue inspection visual
sweeping
coring ball
smoke
Appliance (where included) spillage
Inspected and tested by
J Smith, Smith Building Co.
Not possible, bends
OK
OK
OK
Not included
Tested by J Smith,
GasSafe Reg no. 1234
Not possible, bends
Not applicable
Not applicable
Not applicable
OK
Tested by J Smith,
The Oil Heating Co.
Checked to Section 10,
BS7566:Part 3: 1992 – OK
OK
OK
OK
I/We the undersigned confirm that the above details are correct. In my opinion, these works comply with the relevant requirements in Part J
of Schedule 1 to the Building Regulations.
Print name and title …………………………………………………………………………………… Profession ………………………………………………….
Capacity …(e.g. “Proprietor of Smith’s Flues”, Authorising Engineer for Brown plc)…………….........................…......… Tel no. …...........………
Address ……………………………………………………………………………………………………..........................…. Postcode …........…………
Signed …………………………………………………………………………………………….. Date …………………………………………
Registered membership of … (e.g. GasSafe, OFTEC, HETAS, NACE, NACS) …………………………….………………………………………………
J
Appendix A: Checklist for checking and
testing of hearths, fireplaces, flues and
chimneys

J
69
Blank form – This page may be copied to provide certificates for use
Hearth, fireplace, flues and chimneys
The checklist can help you to ensure that hearths, fireplaces, flues and chimneys are satisfactory. If you have been directly engaged, copies
should also be offered to the client and to the Building Control Body to show what you have done to comply with the requirements of Part J. If
you are a sub-contractor, a copy should be offered to the main contractor.
1. Building address, where work has been carried out…………………………………………………………………………………………
………………………………………………………………………………………………………………………………………………………
………………………………………………………………………………………………………………………………………………………
2. Identification of hearth, fireplace, chimney or flue.
3. Firing capability: solid fuel/gas/oil/all.
4. Intended type of appliance.
State type or make. If open fire give finished
fireplace opening dimensions.
5. Ventilation provisions for the appliance:
State type and area of permanently open air vents.
6. Chimney or flue construction
a) State the type and make and whether new or existing.
b) Internal flue size (and equivalent height, where
calculated – natural draught gas appliances only).
c) If clay or concrete flue liners used confirm they are
correctly jointed with socket end uppermost and state
joining materials used.
d) If an existing chimney has been refurbished with a new
liner, type or make of liner fitted.
e) Details of flue outlet terminal and diagram reference.
Outlet detail:
Complies with:
f) Number and angle of bends.
g) Provision for cleaning and recommended frequency.
7. Hearth, form of construction. New or existing?
8. Inspection and testing after completion
Test carried out by:
Test (Appendix E in AD J) and results
Flue inspection visual
sweeping
coring ball
smoke
Appliance (where included) spillage
I/We the undersigned confirm that the above details are correct. In my opinion, these works comply with the relevant requirements in Part J
of Schedule 1 to the Building Regulations.
Print name and title …………………………………………………………………………………… Profession ………………………………………………….
Capacity …(e.g. “Proprietor of Smith’s Flues”, Authorising Engineer for Brown plc)…………….........................…......… Tel no. …...........………
Address ……………………………………………………………………………………………………..........................…. Postcode …........…………
Signed …………………………………………………………………………………………….. Date …………………………………………
Registered membership of … (e.g. GasSafe, OFTEC, HETAS, NACE, NACS) …………………………….………………………………………………
APPENDIX A JO N L I N E V E R S I O N

J
70
(SEE PARAGRAPH 2.7)
B1 The opening area of a fireplace should be
calculated from the following formula:
B2 Examples of L and H for large and unusual
fireplace openings are shown in Diagram 45.
Appendix B: Opening areas of large or
unusual fireplaces
Diagram 45 Large or unusual fireplace openings. (Note: for use with this Appendix,
measure L, H and W in mm)

J
71
(SEE DIAGRAM 32)
C1 An open-flued boiler with a rated input of
15kW (net) is installed in an appliance
compartment such as a boiler room, which is
ventilated directly to the outside. The design of
the boiler is such that it requires cooling air in
these circumstances.
C2 The cooling air is exhausted via vent D,
which has an area:
C3 Vent E allows the cooling air to enter, as
well as admitting the air needed for combustion
and the safe operation of the flue. It has an area:
C4 The ventilation areas in cm² can be
found by dividing the results given above in mm²
by 100.
Appendix C: Example calculation of the
ventilation requirements of a gas-fired
appliance

J
72
(SEE DIAGRAM 40)
D1 An open-flued appliance is installed in
an appliance compartment such as a cupboard,
which is ventilated via an adjoining room. The air
permeability of the dwelling is 6.0 m3
/(h.m2
) at
50Pa. The appliance has a rated output of 11kW,
i.e. 6kW more than the rating at which permanent
ventilation openings become necessary for the
adjoining room.
D2 Air for combustion and the safe operation
of the flue enters the adjoining room partially
through infiltration, with the balance entering via
vent A, whose area is calculated as follows:
D3 The cooling air for the appliance
compartment is exhausted through vent B,
which has an area:
D4 All of the air for combustion and the safe
operation of the flue as well as cooling air enters
the appliance compartment through vent C,
which has an area:
D5 The ventilation areas in cm² can be found
by dividing the results given above in mm² by 100.
J
Appendix D: Example calculation of the
ventilation requirements of an oil-fired
appliance

J
73
(SEE PARAGRAPHS 1.36 AND 1.54)
E1 This Appendix describes ways of checking
the compliance with J2 of existing, relined or new
flues, and (where included in the work) the
combustion appliance. It applies only to natural
draught flues intended for open-flued appliances.
The procedures described are used only to
assess whether the flue in the chimney, the
connecting fluepipe (and flue gas passages in the
appliance) are free of obstruction and acceptably
gas-tight. In addition, appliance performance
tests, including flue spillage tests to check for
compliance with J2, should be carried out when
an appliance is commissioned to check for
compliance with Part L and as required by the
Gas Safety (Installation and Use) Regulations.
E2 Tests on flues should be carried out at the
most appropriate time during the building work.
Where possible, for example, smoke tests should
be performed when the structure of a chimney is
visible and before the application of finishes such
as plaster or dry lining that could obscure sight of
smoke leakage during testing.
Testing applications
Tests for existing flues
E3 Flues in existing chimneys can be obstructed
by nests, debris resulting from deterioration of the
structure (e.g. brickwork, flue lining material or
pieces of chimney pot) and by soot and tar. Flues
in existing chimneys may also leak as a result of
holes or cracks appearing in the structure and
linings, particularly at joints. The top, exposed part
of a chimney is particularly prone to decay. A way
of checking the state of a flue prior to bringing it
back into use would be to do the following:
a. Sweep the flue. This is intended to clean the
flue to demonstrate that it is essentially free
from obstructions and to enable better visual
inspection and testing of the flue. Tar
deposits caused by burning wood may be
especially hard to dislodge and should be
removed. The debris that comes down the
chimney when sweeping should be examined
for excessive quantities of lining or brick that
are signs that further repairs are necessary.
b. Carry out a visual inspection of the accessible
parts to identify:
i. Deterioration in the structure, connections
or linings which could affect the flue’s
gas-tightness and safe performance with
the proposed combustion appliance.
Examine the interior of the flue and the
exterior of the chimney including in the
roof-space. The presence of smoke or
tar stains on the exterior of a chimney/
breast is a sign of leaks that possibly
indicate damage;
ii. Modifications made whilst the flue was
out of service, such as the fitting of a
ventilator terminal, which would be
incompatible with using the flue with
the intended appliance;
iii. Correct lining and lining sizes for the
proposed new application.
c. Perform checks where necessary to
demonstrate that the flue is free from
restriction: a visual check may be sufficient
where the full length of the flue can be seen.
In cases of doubt, a way of checking this
would be to carry out a coring ball test.
d. Check the gas-tightness of the flue by
carrying out a smoke test.
New masonry and flueblock
chimneys
E4 Check during construction that liners are
installed the right way up, with sockets facing
upwards and joints are sealed so that moisture
and condensate will be contained in the chimney.
E5 Flues in new masonry chimneys can be
obstructed, particularly at bends, by debris left
during construction or by excess mortar falling
into the flue or by jointing material extruded from
between liners and flueblocks. The flues should
be checked to demonstrate that they have been
correctly constructed and are free of restrictions
and acceptably gas-tight.
A way of checking the condition of a new flue prior
to bringing it into use would be to do the following:
a. Carry out a visual inspection of the accessible
parts to check that the lining, liners or
flueblocks are of the correct materials and of
suitable size for the proposed application.
b. Perform checks where necessary to
demonstrate that the flue is free from
restriction: a visual check may be sufficient
where the full length of the flue can be seen.
In cases of doubt, a way of checking this
would be to carry out a coring ball test or to
sweep the flue, which may be more effective
at removing flexible debris that might not be
dislodged by a coring ball.
c. Check the operation and gas-tightness of the
flue by carrying out a smoke test.
New factory-made metal chimneys
E6 A checklist for the visual inspection of a
newly completed factory-made metal chimney
is given in BS EN 15287-1:2007 and additional
checks or particular variants may be included in
manufacturers’ installation instructions. Following
inspection, the chimney should be subjected to a
smoke test.
J
Appendix E: Methods of checking
compliance with requirement J2

74
J APPENDIX E
Relined flues
E7 A flue which has been relined may be
checked to show that it is free from restrictions,
such as from surplus material (where that can
occur) and that it is acceptably gas-tight by using
the same tests as would be applied in the case of
a newly built flue. However, a flue which has been
relined with a flexible metal liner in accordance
with Paragraph 3.36 of this Approved Document
may be assumed to be unobstructed and
acceptably gas-tight. (The use of a coring ball or
inappropriate sweeps brushes can seriously
damage a flexible metal flue liner.)
Appliances
E8 Where a combustion appliance is provided
and connected up to the flue system as part of
the work, the complete system of appliance and
flue should be tested for gas-tightness in addition
to testing the flue separately as above. For gas
appliances, an appropriate spillage test
procedure is given in BS 5440-1:2008. For oil-
and solid-fuel fired appliances, suitable test
procedures are given in BS 5410-1:1997 and BS
EN 15287-1:2007 Annex O respectively.
Flue test procedures
Coring ball test
E9 This test may be appropriate for proving
the minimum diameter of circular flues. It may
also be used to check for obstructions in square
flues but will not detect obstructions in the
corners. (A purpose-made coring ball or plate
may need to be used if the flue is rectangular.) It
is not applicable to fluepipes and should not be
used with flexible metal flue liners. It should be
carried out before smoke testing.
E10 A heavy ball, with a diameter about 25mm
less than that of the flue, is lowered on a rope
from the flue outlet to the bottom of the flue. If an
obstruction is encountered, the blockage should
be removed and the test repeated.
Smoke testing
E11 Where an existing flue is to be checked
with a smoke test, it should first be swept.
E12 Two smoke testing procedures are
described below. Test I confirms the gas-
tightness of the whole flue and may be used for
one serving a solid fuel appliance or if there is
any doubt over the condition of a gas or oil flue.
Test II may be used where the flue is to serve a
gas-fired appliance. Neither test is a substitute
for any spillage or flue draught interference test
required when commissioning the appliance.
Other smoke testing procedures could be used
where these form part of the procedure for the
installation of an approved flue or relining system
Smoke test I
E13 All doors and windows in the room served
by the flue should be closed. The flue should first
be warmed to establish a draught, e.g. with a
blow lamp or electric heater. A suitable number
of flue testing smoke pellets are placed at the
base of the flue, such as in the fireplace recess
or in the appliance if it is fitted, and ignited. When
smoke starts to form, the base of the flue or
fireplace opening should be sealed or the
appliance should be closed, so that the smoke
can only enter the flue. (For example, the recess
opening should be closed off with a board or
plate, sealed at the edges or, if the pellets are in
the appliance, its doors, ashpit covers and vents
should be closed.)
E14 Smoke should be seen to issue freely
from the flue outlet or terminal. When this is
established, the top of the flue is sealed. The
full length of the flue should then be checked,
bearing in mind Paragraph E19; there should
be no significant leakage. The test should be
allowed to continue for at least 5 minutes. The
closures at the top and bottom of the flue should
then be removed.
Smoke test II
E15 All doors and windows in the room served
by the flue should be closed. The flue should first
be warmed to establish a draught. A suitable
flue-testing smoke pellet is ignited at the base
of the flue or in the intended position of the
appliance, so that the smoke is drawn into the
flue with the rising draught. (If the pellets are
placed in a recess at the base of the flue, the
opening between the room and the recess should
be partially closed, such as with a board, but so
as to leave an air entry gap of about 25mm at
the bottom.)
E16 Smoke should be seen to issue freely from
the flue outlet or terminal and not to spill back
into the room. There should be no significant
leakage of smoke from the length of the chimney
inside or outside of the building.
E17 Smoke tests I and II are in line with the
recommendations in BS 5440-1:2008.
Notes in relation to testing
E18 Where warming of the flue is specified, this
is intended to establish a draught, but this may
take more than 10 minutes in the case of large or
cold flues.
E19 Appliances, where fitted, should not be
under fire at the time of carrying out the test.
During a smoke test, smoke should not emerge
from the outlet of any other flue, as this indicates
leakage between flues. When checking for smoke
leakage from a flue, it should be borne in mind
that smoke from a faulty flue can emerge some
distance away from the original fault. In such
cases, the smoke could emerge from such places
as barge overhangs in the end of terrace
dwellings or from window reveals in cavity walls.

75
APPENDIX E J
E20 The purpose of carrying out smoke testing
is to check that flue gases will rise freely through
the flue and to identify whether there are any
faults, such as incorrectly sealed joints or
damage that would cause the flue gases to
escape into the dwelling.
E21 It should be noted that smoke pellets
create a pressure significantly higher than the
pressure required in the product standards for
natural draught chimneys and for flues having a
gas-tightness designation of N1. Flues to this
designation are permitted to have a leakage rate
of up to 2 litre/s/m² flue wall area. Some smoke
leakage may therefore be seen during smoke
tests and it can be a matter of expert judgement
of whether leakage indicates failure.
E22 However, wisps of smoke visible on the
outside of the chimney or near joints between
chimney sections do not necessarily indicate a
fault. If forceful plumes, or large volumes of
smoke are seen, this could indicate a major fault
such as an incorrectly made connection or joint,
or a damaged section of chimney that requires
investigation and remedial action followed by a
repeat of the test.

J
76
F1 The minimum requirements for permanent
ventilation for certain appliances depend on a
knowledge of the air-tightness of the dwelling
where they are to be installed, Dwellings built
after 2008 are likely to have evidence of the
air-tightness either through an individual air
permeability test certificate or through
representative testing of the same design of
dwelling on the same housing development.
F2 Older houses are unlikely to have been
tested but are unlikely to achieve an air
permeability of less than 5.0 m3
/(h.m2
) at 50 Pa
unless the building fabric has been substantially
upgraded. That would include all or most of the
following measures:
• Full double (or triple) glazing
• Effective closures on trickle vents and other
controllable ventilation devices
• All external doors with integral draught seals
and letter box seals
• Internal and external sealing around external
doors and window frames
• Filled cavity or solid walls
• Impermeable overlay and edge sealing of
suspended ground floors
• Careful sealing at junctions between building
elements such as between walls and floors or
ceilings
• Careful sealing around loft hatch
• Careful sealing around chimney or flue
penetrations
• Careful sealing around internal soil pipe
• Careful sealing around domestic water and
heating pipes passing into externally
ventilated spaces
• Careful sealing of all service penetrations in
the building fabric (electricity, gas, water,
drainage, phone, TV aerial, etc.)
• Internal warning pipe for WC
• All cable channels for light switches and
power sockets sealed
• All cable entry for lighting and ceiling roses
sealed. Recessed lighting should not
penetrate ceilings separating loft spaces.
F3 Failure to implement even a few of these
measures will typically mean that the overall air
permeability will probably exceed 5.0 m3
/(h.m2
) at
50 Pa. However, individual rooms in some older
houses with solid walls and solid floors can be
inherently air-tight when fitted with modern
glazing. The situation may therefore need to be
assessed with respect both to the overall
dwelling and to the individual room where the
appliance is to be fitted. If in doubt then assume
that the air permeability is lower than 5.0 m3
/
(h.m2
) at 50 Pa and fit the appropriate permanent
ventilation or seek specialist advice.
Further information on sources of air leakage can
be found in GPG224 Improving airtightness in
dwellings.
Appendix F: Assessing air permeability of
older dwellings in relation to permanent
ventilation requirements

J
77
Appendix G: European chimney designations
G1 This informative appendix provides a
summary of the European chimney designation
scheme. The essence of the scheme is a series
of code letters based on the general chimney
designation scheme of BS EN 1443:2003, an
example of which and their explanation is given
below.
Designation
G2 The designation of a chimney consists of :
Chimney EN 1234 – T 450 N2 D 1 G50
Number of
corresponding
chimney standard
Temperature class
Pressure class N or P or H
Resistance to condensate class,
W (wet) or D (dry)
Corrosion resistance class
Sootfire resistance class G or O followed
by distance to combustible materials
G3 European chimney standards have been
developed based on the material of the flue liner
e.g. clay/ceramic, concrete, metal, and plastic.
Some material based standards have adopted a
different shortened designation e.g. for clay flue
liners a designation Liner – EN 1457-300-A1-N2
means it is suitable for a chimney with the
designation T600 N2 D 3 G, with a nominal
size of 300mm.
G4 The designation of the corrosion
resistance class of a metal chimney product is
dealt with in BS EN 1856-1 and BS EN 1856-2 by
a two-fold approach. A minimum material
specification and thickness is allowed which is
dependent on that which is permitted in member
states regulations, where these exist. Products
upon which a declaration has been made in this
manner are designated Vm. The alternative
approach involves the choice of one of three
corrosion resistance tests. Products meeting the
tests carry the designation V1, V2 or V3, as
appropriate allow the product to be designated
with the Corrosion resistance class 1, 2, or 3
respectively. The material specification still forms
part of the overall designation, and appears
alongside the ‘V’ letter, e.g. Vx-L40045. The
material specification for the liner (or connecting
pipe) is formed by the letter ‘L’ followed by five
digits. The first two digits represent the material
type and the last three digits represent the
material thickness in multiples of 0.01mm.
G5 For the UK, guidance on the minimum
material specification appropriate for the various
applications in terms of corrosion resistance
(solid fuel, gas and oil) is given in the UK National
Annex to BS EN 1856-1 and -2.
For further examples of shortened designation
refer to the specific product standards.
G6 In selecting an appliance for a given
chimney designation, the appliance, irrespective
of the fuel used, is required to generate
combustion products with characteristics equal
or less than those designated for the chimney.
When selecting a chimney suitable for a given
appliance, any chimney with performance
characteristics equal to or higher than those
appropriate for the appliance may be used.
Temperature classes
G7 Temperature classes are set out in Table
G1 and expressed as ‘T’ followed by a number
which is less than or equal to the nominal
working temperature, i.e., the average flue
gas temperature obtained during the nominal/
rated output test (usually the maximum
operating level);
Table G1 Temperature classes
Temperature class Nominal working
temperature °C
T 080  80
T 100  100
T 120  120
T 140  140
T 160  160
T 200  200
T 250  250
T 300  300
T 400  400
T 450  450
T 600  600
Pressure classes
G8 Pressure classes are set out in Table G2
and expressed as either ‘N’, ‘P’ or ‘H’ followed
by either ‘1’ or ‘2’. N relates in general to natural
draught chimneys i.e. operating under negative
pressure where the value 1 or 2 allows for a
different class of product; metal chimneys to BS
EN 1856-1 have the class N1. In the UK the value
N2 will be assigned as a minimum to masonry
chimneys. P and H relate to chimneys which
operate under positive pressure e.g. for fan
assisted applications and diesel generators
respectively. The pressure designation depends
on the gas tightness it achieves, the lower
number being the more onerous, the higher
allowed leakage for positive pressure application
being intended to external installations.

78
J APPENDIX G
Table G2 Pressure classes
Pressure
class
Test
pressure
Pa
Gas tightness
– Maximum
leakage rate
L/s/m2
N1 40 2.0
N2 20 3.0
P1 200 0.006
P2 200 0.120
H1 5000 0.006
H2 5000 0.120
Condensate resistance classes
G9 Condensate resistance class – expressed as
either ‘W’ for wet or ‘D’ for dry operations. A
product designated ‘W’, able to contain condensates
within the flue, is aimed at condensing appliances.
A product designated ‘D’ would usually have flue
gas temperatures high enough to avoid
condensate formation.
Corrosion resistance classes
G10 Corrosion resistance classes are set out in
Table G3 – this is fuel dependant and expressed
as 1, 2 or 3.
Table G3 Corrosion resistance classes (from BS EN 1443-2003)
Corrosion
resistance class
1
Possible fuel types
2
Possible fuel types
3
Possible fuel types
gas

Gas: sulphur-content
 50 mg/m3
Natural gas L + H
Gas
Natural gas L + H
Gas
Natural gas L + H
liquid

Kerosene: sulphur-content
 50 mg/m3
Oil: sulphur-content  0.2 mass
% kerosene: sulphur-content
 50 mg/m3
Oil: sulphur-content > 0.2 mass %
kerosene: sulphur-content
 50 mg/m3
wood Wood in open fire places Wood in open fire places
Wood in closed stoves
coal Coal
peat Peat
Sootfire resistance classes
G11 Sootfire resistance class – expressed as
either ‘G’ with sootfire resistance, or ‘O’ without,
A product assigned the designation ‘G’ has been
tested at 1000ºC for 30 minutes.
Distance to combustible material
G12 The designation of the minimum distance
from the outer surface of the chimney to
combustible material is given as xx expressed in
millimetres (e.g. the distance ‘x-x’ identified in
paragraph 1.45 and diagram 13).

79
J
ACE (Amalgamated Chimney Engineers): White
Acre, Metheringham Fen, Lincoln LN4 3AL
Tel 01526 32 30 09 Fax 01526 32 31 81
BFCMA (British Flue and Chimney Manufacturers
Association): 2 Waltham Court, Milley Lane, Hare
Hatch, Reading, Berkshire RG10 9TH
Tel 0118 940 3416 Fax 0118 940 6258
info@feta.co.uk www.feta.co.uk
BRE (Building Research Establishment Ltd.):
Bucknalls Lane, Garston, Watford, Hertfordshire
WD25 9XX
Tel 01923 66 4000 Fax 01923 66 4010
enquiries@bre.co.uk www.bre.co.uk
BSI (British Standards Institution):
389 Chiswick High Road, London W4 4AL
Tel 020 8996 9000 Fax 020 8996 7400
www.bsigroup.com
CIBSE (Chartered Institution of Building Services
Engineers): 222 Balham High Road, London
SW12 9BS
Tel 020 8675 5211 Fax 020 8675 5449
www.cibse.org
Gas Safe Register: PO Box 6804, Basingstoke
RG24 4NB
Tel 0800 408 5500
www.gassaferegister.co.uk
Environment Agency: Rio House,
Waterside Drive, Aztec West, Almondsbury,
Bristol BS32 4UD
08708 506506
www.environment-agency.gov.uk
Environment Agency Emergency Hotline
0800 80 70 60
HETAS (Heating Equipment Testing and Approval
Scheme): Orchard Business Centre,
Stoke Orchard, Cheltenham, Gloucestershire
GL52 7RZ
Tel 0845 634 5626
www.hetas.co.uk
HSE (Health and Safety Executive):
(1G) Redgrave Court, Merton Road,
Merseyside L20 7HS
Tel 0845 345 0055
www.hse.gov.uk
HSE Infoline: 0845 345 0055
Gas safety advice line: 0800 300 363
IGEM (Institution of Gas Engineers & Managers):
IGEM House, High Street, Kegworth, Derbyshire
DE74 2DA
Tel 0844 375 4436 Fax 01509 678198
www.igem.org.uk
UKLPG: Unit 14, Bow Court, Fletchworth Gate
Burnsall Road, Coventry CV5 6SP
www.uklpg.org
NACE (National Association of Chimney
Engineers): PO Box 849, Metheringham
Lincoln LN4 3WU
Tel 01526 322555
www.nace.org.uk
NACS (National Association of Chimney
Sweeps): Unit 15, Emerald Way, Stone Business
Park, Stone, Staffordshire ST15 0SR
Tel 01785 811732 Fax 01785 811712
nacs@chimneyworks.co.uk
www.chimneyworks.co.uk
NFA (National Fireplace Association): PO Box
583, High Wycombe, Bucks HP15 6XT
Tel 0845 643 1901 Fax 0845 643 1902
www.fireplace.co.uk
OFTEC (Oil Firing Technical Association Ltd):
Foxwood House, Dobbs Lane, Kesgrave
Ipswich IP5 2qq
Tel 0845 65 85 080 Fax 0845 65 85 181
enquiries@oftec.org www.oftec.org
SFA (Solid Fuel Association): 7 Swanwick Court,
Alfreton, Derbyshire DE55 7AS
Tel 01773 835 400 Fax 01773 834 351
sfa@solidfuel.co.uk www.solidfuel.co.uk
Appendix H: Addresses

80
J
BS 41:1973 (1998)
Specification for cast iron spigot and socket flue
or smoke pipes and fittings.
BS EN 303-1:1999
Heating Boilers. Heating boilers with forced
draught burners. Terminology general requirements,
testing and marking.
BS 476-4:1970 (2007)
Fire tests on building materials and structures.
Non-combustibility test for materials. AMD 2483
and AMD 4390.
BS 476-11:1982 (2007)
Method for assessing the heat emission from
building materials.
BS 476-20:1987
Method for determination of the fire resistance
of elements of construction (general principles).
BS 476-21:1987
Methods for determination of the fire resistance
of loadbearing elements of construction.
BS 476-22:1987
Methods for determination of the fire resistance
of non-loadbearing elements of construction.
BS EN 449:2002 + a1:2007
Specification for Dedicated Liquid Petroleum Gas
Appliances. Domestic Flueless Space Heaters
(including Diffusive Catalytic Combustion Heaters).
BS 715:2005
Specification for metal flue pipes, fittings, terminals
and accessories for gas-fired appliances with a
rated input not exceeding 60kW. AMD 8413.
BS 799-5:1987
Oil Burning Equipment. Specification for Oil
Storage Tanks.
BS 1181:1999
Specification for clay flue linings and flue terminals.
BS 1251:1987
Specification for open fireplace components.
BS EN 1443:2003
Chimneys. General Requirements.
BS 1449-2:1983
Specification for stainless and heat-resisting steel
plate, sheet and strip. AMD 4807, AMD 6646 and
AMD 8832.
BS EN 10268:2006
Cold rolled steel flat products with high yield
strength for cold forming. Technical delivery
conditions.
BS EN 1457:2009
Chimneys. Clay/ceramic flue liners. Requirements
and test methods.
BS EN 1806:2006
Chimneys. Clay/ceramic flue blocks for single
wall chimneys. Requirements and test methods.
BS 1846-1:1994
Glossary of Terms Relating to Solid Fuel Burning
Equipment. 1994 Domestic appliances.
BS EN 1856-1:2003
Chimneys. Requirements for metal chimneys.
System chimney products.
BS EN 1856-2:2004
Chimneys. Requirements for metal chimneys.
Metal liners and connecting flue pipes.
BS EN 1857:2003 + A1:2008
Chimneys. Components. Concrete flue liners.
BS EN 1858:2003
Chimneys. Components. Concrete flue blocks.
BS EN 1859:2009
Chimneys. Metal chimneys. Test methods.
BS 2869:2006
Fuel oils for agricultural, domestic and industrial
engines and boilers. Specification.
BS EN 1859:2000
Chimney, Metal chimneys. Test methods.
BS 2869-2:1998
Fuel oils for non-Marine use. Specification for fuel
oil for agricultural and industrial engines and burners
(Classes A2, C1, C2, D, E, F, G and H). AMD 6505.
BS 4543-1:1990
Factory-made insulated chimneys. Methods of
test. AMD 8379.
BS 4543-2:1990
Factory-made insulated chimneys. Specification
for chimneys with stainless steel flue linings for
use with solid fuel fired appliances. AMD 8380.
BS 4543-3:1990
Factory-made insulated chimneys. Specification
for chimneys with stainless steel fluelining for use
with oil fired appliances. AMD 8381.
BS 4876:1984
Specification for performance requirements for
domestic flued oil burning appliances (including
test procedures).
BS 5410-1:1997
Code of practice for oil firing. Installations up to
44kW output capacity for space heating and hot
water supply purposes. AMD 3637.
BS 5410-2:1978
Code of practice for oil firing. Installations of 45
kW and above output capacity for space heating,
hot water and steam supply services.
BS 5440-1:2008
Installation and maintenance of flues and
ventilation for gas appliances of rated input not
exceeding 70kW net (1st, 2nd and 3rd family
gases). Specification for Installation and
maintenance of flues.
Standards referred to

81
STANDARDS REFERRED TO J
BS 5440-2:2000
Installation and maintenance of flues and
ventilation for gas appliances of rated input not
exceeding 70kW net (1st, 2nd and 3rd Family
Gases). Specification for installation and
maintenance of ventilation for gas appliances.
BS 5482-1:2005
Code of practice for domestic butane- and
propane-gas-burning installations. Installations at
permanent dwellings, residential park homes and
commercial premises, with installation pipework
sizes not exceeding DN 25 for steel and DN 28
for corrugated stainless steel or copper.
BS 5546:2000
Specification for installation of hot water
supplies for domestic purposes, using gas fired
appliances of rated input not exceeding 70kW.
BS 5854:1980 (1996)
Code of practice for flues and flue structures
in buildings.
BS 5864:2004
Specification for Installation in Domestic Premises
of Gas-Fired Ducted-Air Heaters of Rated Input
Not Exceeding 60kW.
BS 5871-1:2005
Specification for Installation of Gas Fires, Convector
Heaters, Fire/Back Boilers and Decorative Fuel
Effect Gas Appliances. Gas Fires, Convector
Heaters and Fire/Back Boilers and heating stoves
(1st, 2nd and 3rd Family Gases).
BS 5871-2:2005
Effect Gas Appliances. Inset Live Fuel Effect Gas
Fires of Heat Input Not Exceeding 15kW (2nd and
3rd Family Gases).
BS 5871-3:2005
Effect Gas Appliances. Decorative Fuel Effect Gas
Appliances of Heat Input Not Exceeding 20kW
(2nd and 3rd Family Gases).
BS 6172:2004
Specification for Installation of Domestic Gas
Cooking Appliances (1st, 2nd and 3rd Family Gases).
BS 6173:2001
Specification for Installation of Gas Fired Catering
Appliances for Use in All Types of Catering
Establishments (1st, 2nd and 3rd Family Gases).
BS EN 15287-1:2007
Chimneys. Design, installation and commissioning
of chimneys. Chimneys for non-roomsealed
heating appliances.
BS 6798:2009
Specification for Installation of Gas-Fired Boilers
of Rated Input Not Exceeding 70kW.
BS 6999:1989 (1996)
Specification for Vitreous-Enamelled Low-
Carbon-Steel Fluepipes, Other Components and
Accessories for Solid-Fuel-Burning Appliances
with a Maximum Rated Output of 45kW.
BS 7435-1:1991 (1998)
Fibre Cement Flue Pipes, Fittings and Terminals.
Specification for Light quality Fibre Cement Flue
pipes, Fittings and Terminals.
BS 7435-2:1991
Fibre Cement Flue Pipes, Fittings and Terminals.
Specifications for heavy quality cement flue
pipes, fittings and terminals.
BS 7566:
Installation of Factory-Made Chimneys to
BS 4543 for Domestic Appliances
BS 7566-1:1992 (1998)
BS 4543 for Domestic Appliances. Method of
Specifying Installation Design Information.
BS 7566-2:1992 (1998)
BS 4543 for Domestic Appliances. Specification
for Installation Design.
BS 7566-4:1992 (1998)
BS 4543 for Domestic Appliances.
Recommendations for Installation Design
and Installation.
BS 8303-1:1994
Installation of Domestic Heating and Cooking
Appliances Burning Solid Mineral Fuels,
Specification for the Design of Installations.
BS 8303-2:1994
Specification for Installing and Commissioning
on Site.
BS 8303-3:1994
Recommendations for Design and on Site
Installation.
BS EN 10088-1:2005
Stainless Steels. List of Stainless Steels.
BS EN 13384-1:2002 + A2:2008
Chimneys. Thermal and fluid dynamic calculation
methods. Chimneys serving one appliance.
BS EN 14213:2003
Heating fuels. Fatty acid methyl esters (FAME).
Requirements and test methods.
BS EN 15287-1:2007
Chimneys. Design, installation and
commissioning of chimneys.
O N L I N E V E R S I O NREFERREDO N L I N E V E R S I O NREFERRED TO O N L I N E V E R S I O NTO

82
J
Government
Approved Document J: 2002 Edition:
Supplementary Guidance on the UK
Implementation of European Standards for
Chimneys and Flues, ODPM (2004). Available to
download from www.planningportal.gov.uk.
The Gas Safety (Installations and Use)
Regulations 1998.
Gas Appliances (Safety) Regulations 1995.
Workplace, Safety and Welfare, Workplace
(Health, Safety and Welfare) Regulations 1992,
Approved Code of Practice L24, HSE Books
(1992). ISBN 978 0 71760 413 5
Guide to Condensing Boiler Installation
Assessment Procedure for Dwellings. Office of
the Deputy Prime Minister (2005).
ISBN 978 1 85112 784 9
Building Research Establishment
BR 414 (2001) Protective measures for housing
on gas contaminated land.
ISBN 978 1 86081 460 0
BR 211 (2007) Radon: guidance on protective
measures for new buildings (including
supplementary advice for extensions,
conversions and refurbishment) (2007 edition).
Chartered Institution of Building Services
Engineers
CIBSE Guide B: Heating, Ventilating, Air
Conditioning and Refrigeration, (2005).
ISBN 978 1 90328 758 3
Energy Saving Trust
GPG224 Improving airtightness in dwellings (2005).
Environment Agency
The Control of Pollution (Oil Storage) (England)
Regulations (2001).
Pollution Prevention Guidelines PPG2 – Above
Ground Oil Storage Tanks (2004).
Pollution Prevention Guidelines PPG27-
Installation, Decommissioning and Removal of
Underground Storage Tanks (2002).
Masonry Bunds for Oils Storage Tanks, CIRIA/
Environment Agency Joint Guidelines
Concrete Bunds for Oils Storage Tanks, CIRIA/
Environment Agency Joint Guidelines
Available to download from http://publications.
environment-agency.gov.uk.
Health and Safety Executive
Safety in the installation and use of gas systems
and appliances, Approved Code of Practice and
Guidance L56, HSE Books.
ISBN 978 0 71761 635 0
HETAS
HETAS Information Paper 1/007 Chimneys in
Thatched Properties (2009).
Oil Firing Technical Association (OFTEC)
OFTEC Oil Fired Appliance Standard. OFS A100.
Heating Boilers with Atomising Burners. Outputs
up to 70kW. Maximum Operating Pressures of 3
Bar (2004).
OFTEC Oil Fired Appliance Standard. OFS A101.
Oil Fired Cookers with Atomising or Vaporising
Burners with or without Boilers. Heat Outputs up
to 45kW (2004).
OFTEC Technical Book 3: Installation
requirements for oil fired equipment
1st Edition (2006).
OFS T100 Oil Firing Equipment Standard –
Polyethylene Oil Storage Tanks for Distillate
Fuels (2008).
OFS T200 Oil Firing Equipment Standard –
Steel Oil Storage Tanks and Tank Bunds for use
with Distillate Fuels, Lubrication Oils and Waste
Oils (2007).
UKLPG
Code of Practice 1 Bulk LPG Storage at Fixed
Installations Part1: Design, Installation and
Operation of Vessels Located Above Ground
(January 2009).
Other publications referred to

J
83
A
Access
Appliances 1.60
Flues 1.47, 1.49, Diagram 14
Accreditation page 7
Air permeability assessment
Appendix F
Air supply 1.2–1.4, Diagram 8
Flueless appliances 1.19
Gas appliances 3.10, 3.15–3.16,
Diagram 32
Oil appliances 4.3, Diagram 40
Solid fuel appliances 2.1–2.3, Table 1
See also Air vents
Air-tight membranes 1.17
Air vents 1.3–1.4
Equivalent area 1.12–1.14
Gas appliances Diagram 32
Grilles and meshes 1.15
Location 1.11, 1.16, Diagram 10
Noise 1.16
Oil appliances Diagram 40
Permanently open 1.10–1.17
Solid floors Diagram 11
Solid fuel appliances 2.1–2.3
Appliance compartments
Definition 0.4
Oil appliances Diagram 40
Ventilation 1.5–1.7
Approved Document J
Purpose page 3
Types of work covered page 5
Architectural interest page 6
B
Back boilers 3.39, Diagram 36
Balanced compartments
Definition 0.4
Ventilation 1.7
Balanced flues
Definition 0.4
Flue outlets 3.23, Diagram 34
Bathrooms
Gas appliances 3.5
Oil appliances 4.2
Bedrooms
Gas appliances 3.5
Oil appliances 4.2
Biofuel
Liquid 4.1, 5.2, Table 8
Solid 0.4, page 8, Table 3, Table G3
Boundaries Diagram 1
Definition 0.4
Flue outlets 1.52, 3.23, Diagram 34
LPG storage installations 5.15,
Diagram 43
Oil storage installations Table 10
British Standards page 80–81
BS 41:1973 (1998) 1.32
BS 715 3.37
BS 1251:1987 Diagram 29
BS 2869:1998 5.2
BS 5410-1:1997 1.25, 5.2, 5.6,
page 61, Appendix E8,
BS 5440 page 55
BS 5440-1:2008 1.23, 1.25, 1.42,
3.22, 3.37, Appendix E8
BS 5440-2:2009 3.15
BS 5482-1:2005 5.14
BS 5546:2000 page 55
BS 5864:2004 page 55
BS 5871:2005 page 55, 3.22,
Diagram 31
BS 6172:2004 page 55
BS 6173:2001 page 55
BS 6798:2009 1.60, page 55
BS 6999:1989 (1996) 1.32
BS 8131:1997 5.22
BS 8303:1994 2.33
BS EN 1443:2003 1.26, 1.27, 2.20,
4.23, Appendix G1, Table G3
BS EN 1457:2009 1.27
BS EN 1806:2006 1.29, 2.17, 3.30,
4.15
BS EN 1856-1:2003 1.42, 1.45, 1.46,
2.20, 3.36, Appendix G4, Appendix
G4–5
BS EN 1856-2:2004 1.32, 1.40, 2.20,
3.28, 4.13, Appendix G4, Appendix
G4–5
BS EN 1857:2003 (2008) 1.27, 2.20,
3.28, 4.13
BS EN 1858:2003 2.17, 3.30, 4.15,
4.21
BS EN 13141-1:2004 1.12
BS EN 13384-1:2005 2.8
BS EN 14213:2003 5.2
BS EN 14471:2005 1.41
BS EN 15287-1:2007 1.42, 2.33,
Appendix E8
BS EN 15827-1:2007 4.22
BS EN 50291:2001 2.35
BS EN 50292:2002 2.36
Building Control Body (BCB)
Definition 0.4
Notification of work page 6
Building Regulations page 9
C
Capacity
Definition 0.4
Carbon monoxide alarms 1.1, 2.33,
2.34–2.36
CE marking page 7, 3.19, 3.42
Certification
Competent person self-certification
schemes page 6
Product certification schemes page 7
Change of appliance type 1.36–1.39
Change of use page 5, 1.31, Diagram 12
Chimneys
Checklist Appendix A
Condensate resistance 1.26,
Appendix G9
Corrosion resistance Table G3,
Appendix G4–5, Appendix G10
Definition 0.4
European designations Appendix G
Fire prevention 2.18, Diagram 21,
Appendix G11–12
Gas appliances 3.27, 3.29–3.32
Debris collection space 3.38
Fire prevention 3.33–3.34, Table 7
Minimum performance
designations Table 6
Oil appliances 4.9–4.12, 4.14–4.22
Fire prevention 4.18–4.19, Table 9
Minimum performance
Pressure classes Table G2,
Appendix G8
Solid fuel appliances 2.17, 2.19–2.20,
Table 3
Fire prevention 2.18, Diagram 21
Minimum performance
Wall thickness 2.17, Diagram 20
Sootfire resistance Appendix G11
Structure Diagram 2
Temperature classes Table G1,
Appendix G7
See also Factory-made metal
chimneys; Flueblock chimneys;
Flues; Masonry chimneys
Clean Air Act 1993 page 8
Combustion appliances
Definition 0.4
Combustion products
Gas-tightness tests Appendix E8
Spillage into room 1.20–1.23,
Appendix E8
Competent person self-certification
schemes page 6
Compliance with requirements page 3
Checking Appendix E
Independent certification and
accreditation schemes page 7
Responsibility for page 4, 1.54
Self-certification page 6
Condensates in flues 1.26
Condensing appliances
Flue liners 1.26, 1.41
Flue outlets 3.23, 4.7
Conservation areas page 6
Control of Pollution (Oil Storage)
(England) Regulations 2001
5.7–5.12
Coring ball test Appendix E9–10
D
Debris collection space 2.16, 3.38
Decorative fuel effect (DFE) fires
Diagram 31, 3.11–3.12
Flues 3.22
Hearths Diagram 37
Depressurisation 1.20–1.23
Designation system
Chimneys Appendix G
Definition 0.4
Draught break
Definition 0.4
Draught diverter Diagram 3
Definition 0.4
Draught stabiliser Diagram 3
Definition 0.4
Dry lining around fireplace 1.53
Ducts
Size measurement 0.5, Diagram 7
E
Equivalent area 1.12–1.14
Definition 0.4
European chimney designations
Appendix G
European Technical Approval page 7
Exemptions page 6–7
F
Factory-made metal chimneys 1.42–
1.46, Table 3
Checking Appendix E6
Definition 0.4
Gas appliances 3.32
Guarding 1.45, 3.32, 3.35, 4.20
Oil appliances 4.17
Solid fuel appliances 2.19
Fanned draught Diagram 4
Definition 0.4
Fire compartments
Definition 0.4
Flues penetrating 1.46, 3.34, 4.19
Fireplace canopies Diagram 23
Fireplace gathers 2.21, Diagram 22,
Diagram 23
Fireplace linings 2.31, Diagram 29
Index

84
J INDEX
Fireplace openings Appendix B,
Diagram 45
Dry lining around 1.53
Fire protection 2.30, 2.32–2.33
Flue size as percentage of 2.7
Fireplace recesses Diagram 5
Definition 0.4
Fire protection 2.18, 2.30, Diagram 28
Linings 2.31
Fire protection
Factory-made metal chimneys 1.45,
3.35, Diagram 13
Fireplaces and hearths 2.25–2.33,
3.40–3.41, 4.25–4.27
Flues 3.33–3.34, 4.18–4.19, Table 7
Connecting fluepipes 2.14–2.15,
3.35, Diagram 19
Flue outlets 2.12
LPG storage installations 5.14–5.18,
Diagram 43, Table 11
Masonry chimneys 1.31, 2.18,
Diagram 12, Diagram 21
Oil storage installations 5.4–5.6,
Table 10
Fire resistance
Definition 0.4
Fire walls 5.5, 5.16–5.18
Definition 0.4
Flexible metal flue liners 1.40, 4.22
Floor vents Diagram 11, 1.17
Flueblock chimneys 1.29–1.30, 2.17,
3.30–3.31, Diagram 20
Checking Appendix E4–5
Definition 0.4
Gas appliances 3.30–3.31
Minimum performance designations
Table 3
Oil appliances 4.15–4.16
Flue box
Definition 0.4
Flue gas
Spillage 1.20, 1.55
Temperatures 4.9–4.12, Appendix G7
Flueless appliances Diagram 4
Air supply 1.19, 3.15–3.16, Diagram 8,
Diagram 33
Definition 0.4
Gas appliances 3.8–3.9, 3.15–3.16,
Diagram 33
Flue liners 1.26, 1.27
Checking Appendix E7
Definition 0.4
Flexible metal 1.40, 3.37
Table 3
Re-lining 1.35, 1.37–1.40, 2.20,
3.36–3.37, 4.21–4.22
Repair 1.34–1.35
Solid fuel appliances 2.20
Flue outlets Diagram 17, Diagram 18
Configuration 1.49
Definition 0.4
Gas appliances 3.23–3.26, Diagram 34,
Diagram 35
Near boundaries 1.52
Oil appliances 4.6–4.8, Diagram 41
Terminals and guards 3.25–3.26, 4.8
Fluepipes
Configuration 1.49, Diagram 15
Connecting 1.32–1.33
Gas appliances 3.28
Oil appliances 4.13
Definition 0.4
Gas appliances 3.20, 3.28, Table 6
Guarding 4.20
Location and shielding 2.14–2.15,
4.19–4.20
Oil appliances 4.4, 4.13, Table 8
Plastic 1.41
Solid fuel appliances 2.4, 2.13–2.15
Testing 1.55
Flues Diagram 2
Access Diagram 14
Concealed 1.47, Diagram 14
Condensate resistance 1.26,
Appendix G9
Configuration 1.48–1.49, Diagram 15
Definition 0.4
Gas appliances 3.5
Flue outlets 3.23–3.26, Diagram
34–35
Height of flues 3.21–3.22
Table 7
Provision 3.27, Table 6
Size of flues 3.17–3.20, Table 5
Gas tightness tests Appendix E7–8
Inspection and cleaning 1.49,
Appendix E3, Diagram 15
Means of access 1.47, 1.49,
Diagram 14
Notice plates 1.57–1.58, Diagram 16
Oil appliances
Burning Class D oil 4.23
Flue liners 4.21–4.22
Flue outlets 4.6–4.8, Diagram 41
Table 9
Provision 4.9–4.12
Size of flues 4.4–4.5
Provision 1.23
Repair 1.34–1.35
Re-use 1.36–1.39
Size measurement 0.5, Diagram 7
Solid fuel appliances
Flue liners 2.20
Flue outlets 2.10–2.12
Location and shielding 2.14–2.15
Size of flues 2.4–2.7, Table 2
Testing 1.55, Appendix E3,
Appendix E9–22
See also Chimneys; Flue liners;
Fluepipes
G
Gas appliances 3.1–3.42, 3.38
Air supply 3.10, 3.15–3.16, Diagram
32, Diagram 33, Appendix C
Back boilers 3.39
Combustion product spillage 1.20,
1.23
Flueless 3.8–3.9, 3.15–3.16,
Diagram 33
Flues 3.7
Chimney construction 3.29–3.32
Height 3.21–3.22
Location and shielding 4.18–4.20
Provision 3.27, Table 6
Size 3.17–3.20, Table 5
Hearths 3.40–3.41, Diagram 37,
Diagram 38
Regulations 3.1–3.5
Roof space installations 1.60
Shielding 3.42, Diagram 39
Standards approach page 55
Types of installation 3.6–3.16,
Diagram 4, Diagram 31, Diagram 32
Gas Safety (Installation and Use)
Regulations 3.1–3.5
Gas tightness tests Appendix E7–8
Gathers 2.21, Diagram 22, Diagram 23
H
Hearths 1.56, Diagram 6
Definition 0.4
Gas appliances 3.40–3.41, Diagram 37
Notice plates 1.57–1.58, Diagram 16
Solid fuel appliances 2.22–2.29, 2.32–
2.33, Diagram 24–27, Diagram 30
Heat input rate
Definition 0.4
Historic buildings page 5–6
I
Inset live fuel effect (ILFE) fires
3.13–3.14, Diagram 31, Diagram 37
Installation instructions
Definition 0.4
Installers
Certification and accreditation
page 6, page 7, 3.3
Responsibility for compliance 1.54
Instantaneous water heaters 3.5, 3.9
L
Legislation page 8
Limitation on requirements page 5
Listed buildings page 6
LPG cylinders
Location and support 5.19–5.20,
Diagram 44
LPG pipework 5.21–5.22
LPG storage installations 5.13–5.21
Building Regulations 3.5
Tank location and protective
measures 5.14–5.18, Table 11,
Diagram 43
M
Masonry chimneys 1.27–1.28,
Diagram 20
Checking Appendix E4–5
Fire prevention 1.31, 2.18,
Gas appliances 3.29
Table 3
Oil appliances 4.14
Material change of use page 5, 1.31,
Diagram 12
Materials and workmanship page 7
Metal chimneys
See Factory-made metal chimneys
Minor works page 6
Multi-fuel appliances 2.6
N
National parks page 6
Natural draught flues 1.48–1.49,
Diagram 4
Non-combustible material
Definition 0.4
Non-notifiable work page 6
Notice plates 1.57
Notification of work page 6
Notified Body
Definition 0.4

85
INDEX J
O
Air supply 4.3, Diagram 40,
Appendix D
Burning Class D oil 4.23
Combustion product spillage 1.20,
1.23
Flue gas temperatures 4.9–4.12
Flues
Chimney construction 4.13–4.17
Table 9
Provision 4.9–4.12, Table 8
Size 4.4–4.5
Hearths 4.24–4.27, Diagram 42
Shielding 4.25–4.27
Standards approach page 61
Oil storage installations 5.1–5.12
Fire protection 5.4–5.5, Table 10
Heating 5.2–5.3
Pollution prevention 5.7–5.12
Oil supply pipes 5.6
Open fireplaces Diagram 29
Open-flued appliances Diagram 4
Air supply 1.4–1.5, 1.18, Diagram 8
Definition 0.4
Gas appliances 3.17–3.22, Diagram
32, Appendix C, Natural draught
flues 1.48–1.49, 3.17–3.22
Oil appliances 4.2, Appendix D
P
Performance requirements 1.1
Plastic fluepipes 1.41
Prefabricated appliance chambers
2.30, Table 4
Definition 0.4
Product certification schemes page 7
Publications (excluding BSI and
European Standards) page 82
Above Ground Oil Storage Tanks
(CLG PPG2, 2004) 5.7
Bulk LPG Storage at Fixed
Installations (UKLPG Code of
Practice, 2009) 5.14
Good Building Guide (BRE GBG 25)
1.20
Installation, decommissioning and
removal of underground storage
tanks (CLG PPG27, 2002) 5.7
Protective measures for housing
on gas contaminated land
(BR 414, 2001) 1.17
Radon: guidance on protective
measures for new buildings
(BR 211, 2007) 1.17
Safety in the installation and use
of gas systems and appliances
(HSE) 3.3
R
Radiant convector gas fires 3.13–3.14,
Diagram 31
Radon gas extraction 1.20
Rated heat input
Definition 0.4
Rated heat output
Definition 0.4
Roof space installations 1.60
Room-sealed appliances Diagram 4
Air supply 1.8, Diagram 8
Definition 0.4
S
Self-certification schemes page 6
Shower rooms 3.5, 4.1
Smoke spillage 1.55
Smoke testing Appendix E11–22
Solid biofuel
Definition 0.4
Solid floors Diagram 11
Air supply 2.1–2.3, Table 1
Carbon monoxide alarms 2.34–2.36
Chimney wall thickness 2.17,
Diagram 20
Combustion product spillage 1.20
Fireplace gathers 2.21, Diagram 22,
Diagram 23
Fireplace linings 2.31, Diagram 29
Fireplace recesses 2.30, Diagram 28
Fire prevention 2.18, 2.32–2.33,
Table 3, Diagram 21, Diagram 30
Flues
Connecting fluepipes 2.13–2.15
Flue outlets 2.10–2.12, Diagram
17–18
Size of flues 2.4–2.7
Hearths 2.22–2.29, Diagram 24–27
Prefabricated appliance chambers
2.30, Table 4
Spillage tests 1.55
Standards page 7
T
Technical specifications page 7
Thatched roofs 2.12
Throat Diagram 29
Definition 0.4
V
Ventilation
Air permeability assessment
Appendix F
Appliance compartments 1.5–1.7
Flueless appliances 1.19, 3.15–3.16,
Gas appliances 3.15–3.16, Diagram
33, Appendix C
Oil appliances Appendix D
Room 1.4, 1.8–1.9, 1.18–1.19,
1.20–1.23
See also Air supply; Air vents
Ventilator free areas Diagram 9
W
Workmanship page 7
Workplace (Health, Safety and
Welfare) Regulations 1992 page 8

The Building Regulations 2010
Published by NBS, part of RIBA Enterprises Ltd, and available from:
RIBA Bookshops Mail Order
15 Bonhill Street
London EC2P 2EA
Telephone orders/General enquiries: 020 7256 7222
Fax orders: 020 7374 2737
Email orders: sales@ribabookshops.com
Or order online at:
www.thenbs.com/buildingregs
RIBA Bookshops
RIBA, 66 Portland Place, London WIB 1AD. Telephone 020 7256 7222
ISBN 978 1 85946 371 0
Stock code 72231
© Crown Copyright, 2010
Reprint December 2010, with corrections
Copyright in the typographical arrangement rests with the Crown.
This publication, excluding logos, may be reproduced free of charge in any format
or medium for research, private study or for internal circulation within an
organisation. This is subject to it being reproduced accurately and not used in a
misleading context. The material must be acknowledged as Crown copyright and
the title of the publication specified. This document/publication is value added.
If you wish to re-use, please apply for a Click-Use Licence for value added
material at www.opsi.gov.uk/click-use/system/online/pLogin.asp, or by writing to
the Office of Public Sector Information, Information Policy Team, Kew, Richmond,
Surrey TW9 4DU. Email: licensing@opsi.gov.uk. If you require this publication in
an alternative format please email alternativeformats@communities.gsi.gov.uk.
www.thenbs.com
BuildingRegulations2010APPROVEDDOCUMENTJCombustionappliancesandfuelstoragesystems
J1 Air supply
J2 Discharge of products of combustion
J3 Warning of release of carbon monoxide
J4 Protection of building
J5 Provision of information
J6 Protection of liquid fuel storage systems
J7 Protection against pollution
JAPPROVED DOCUMENT
Combustion appliances and
fuel storage systems
Cert no. TT-COC-002168
2010
edition
incorporating
further
2010
am
endm
ents

Br pdf ad_j_2010_v2

More Related Content

Similar to Br pdf ad_j_2010_v2 (20)

More from wirethehouse (20)

Br pdf ad_j_2010_v2