Brooding guide

Brooding Guide for Optimum Breeder Development
Introduction
The brooding period, generally considered as the period of time from placement through
14 days, is perhaps the most important time in a bird’s life. The brooding period is the most
sensitive because the bird is changing from an immature thermo regulation system to a
mature system. Survival of the newly hatched chick is largely dependent on how quickly
and efficiently the transition is made from the hatcher to the farm environment. At no other
time during the flock’s life is a service person’s and producer’s job more important. Mistakes
made during this critical time may be irreversible and negatively impact performance for the
entire life of the flock.
COBB

COBB 1
•
•
Immune system
An understanding of the physiological changes that occur in the chick during the first 2 weeks
of life makes it easier to fully appreciate the importance of this developmental phase. These
changes include development of the:
Passive immunity is occurring as a result of the transfer of antibodies from the
breeder hen through yolk absorption to the developing chick (~2-3 weeks).
Active immunity is developing from in-ovo & day old vaccinations, field vaccinations
and exposure to field pathogens.
•
•
Digestive system
Rapid internal organ growth required for digestion (liver, intestines, pancreas, spleen
and bursa).
Feed conversion & growth rate are more efficient during this time than at any other
time in the bird’s life.
•
Skeletal system
Rapid growth and thickening of long bones required for leg strength and mineral
metabolism later in life.
•
Thermoregulation
Chicks do not have the ability to regulate body temperature for the first 5 days and
thermo regulation is not fully developed until 2 weeks of age. Chick survival is highly
dependent on the grower to provide the proper environmental temperature.
Improper brooding practices can result in poor livability, poor flock uniformity and overall
poor performance in the pullet and hen house leading to a higher chick cost. Obtaining a
body weight at 7 days is an excellent indicator of how successful the brooding management
has been. This weight can be used as a “tool” to help illustrate the difference between well
managed and poorly managed farms. The target body weight at 7 days is approximately
4 to 4.5 times the day old chick weight. If this level of performance is not achieved, pre-
placement and brooding management techniques should be critically evaluated.
The effects of early stress may not be seen until much later in life and may negatively affect
the subsequent reproductive performance of the flock. The main reason for insufficient
weight gain is low feed consumption. Feed presentation in the form of either a mash or fine
crumb with minimal dust content is necessary to obtain adequate feed intake during the first
week. An insufficient feed amount and/or insufficient feeder space will negatively affect feed
intake, weight gain and flock uniformity. Research has shown that early protein intake has
an effect on 4 week weight, flock uniformity and ultimately egg production.
The 7 Brooding Fundamentals to maximizing performance and minimizing cost include:
•
•
•
•
•
•
•
Pre-Placement Preparation
Feed Management
Light Management
Water Management
Temperature Management
Air Quality & Ventilation
Grading the Young Flock

COBB2
The key to successful rearing lies in an effective management program starting well before
chicks arrive at the farm. Rearing facilities should be clean, disease free and biosecure
before placing the flock. Detailed cleaning and hygiene procedures are described in the Cobb
Breeder Management Guide. Biosecurity regulations should be enforced year round even
when the farm is empty between placements.
The entire floor should be covered with 3-4” (7.5-10.0 cm) of a good quality litter material to
prevent heat loss. Litter should be spread as evenly as possible throughout the house to help
ensure an even floor temperature. Uneven floor temperatures can cause chicks to huddle in
pockets or under equipment. In addition to this, uneven litter can impede chick mobility and
restrict access to feed and water due to the uneven height of feed and water lines.
Water lines should be cleaned, sanitized and thoroughly flushed prior to flock placement.
Water line pressure should be readjusted from the previous flock to a pressure suitable for
the baby chick.
Stocking density should take into consideration environmental/local climatic conditions and the
type of equipment being used. Males should be given proportionately more floor space than
females to help ensure they achieve target body weight goals.
The Pre-Placement period is the ideal time to prepare the “Chick Comfort Zone”; the area
surrounding the edge of the brooder where the baby chick does not have to make a choice
between feed, water or heat. Equipment placement is critical to accomplish this objective.
PRE-PLACEMENT PREPARATION
Females
10.8
1.0
5.0
2.0
20
20-30
1.5
0.6
10-12
80-100
10.8
1.0
7.5
3.0
20
20-30
1.5
0.6
10
80
Floor
Feeder
Water
Litter (birds/m2
)
Litter (ft.2
/bird)
Chain (cm/bird)
Chain (in./bird)
Pan Feeder (birds/pan)
Tube Feeder (birds/tube)
Trough (cm/bird)
Trough (in./bird)
Nipples (birds/nipple)
Bell Drinker (birds/bell)
Males
Sex Separate Brooding Space Requirements (0-4 weeks)

COBB 3
The use of supplemental feeders at placement is recommended to help chicks get off to the
best start possible. Trays should be provided at the rate of 1 per 50 chicks and should be
placed between the main feed and drinker lines and adjacent to the brooders. Supplemental
feeders should be provided for the first 7-10 days, or 14 days for the lighter birds if chicks
are graded.
Never place supplemental feed or water directly beneath the brooder where excessive heat
may drive chicks away from feed and water. Ensure that supplementary feed never runs empty
and remains fresh at all times, never allowing it to become stale or moldy.
“Top dressing” with a small quantity of feed several times throughout the day stimulates feed
consumption and is a better management practice than having too much feed out at any given
time. After the first 2-3 days, feeder trays should gradually be moved closer to the automated
feeding system, followed by trays being removed from the house gradually over several days.
It is a good management practice to gently walk chicks 2-3 times per day to help stimulate feed
and water consumption the first several days post placement. Flocks that fail to make a quick
transition to feed and water can potentially suffer from higher early mortality.
If chicks are placed the same day they hatch, the crops of chicks should be checked the
morning after placement (“Crop Check”) to ensure they have found feed and water. If they are
placed the day following hatch, crops should be checked 8 hours post placement to evaluate
feed and water intake. At this time, a minimum of 95% of the crops should feel soft and pliable
indicating chicks have successfully located feed and water. Hard crops indicate chicks have
not found adequate water and water availability should be checked immediately. Swollen and
distended crops indicate chicks have located water but insufficient feed and in this case the
availability and consistency of the feed should be immediately evaluated.
feed management

Chick Crop Check - Sample 100 Chicks
A minimum of 95% of the bird’s crops should be filled upon examination the morning
after placement.
If the crops are checked eight hours after placement a minimum of 85% crop fill
should be achieved containing both feed and water.
Sample 100 chicks per brood area
Evaluate crop fill and indicate results on form as below:
•
•
•
•
Crop fill
Evaluation
EmptyNo. of chicks Full-Pliable
Feed & water
Full-Hard
Only feed
Full-Soft
Only water
Starter feed should be fed during this period in either a mash or fine crumb form. Males
and females should be given the amount of feed necessary to achieve the recommended
bodyweight at 7 days. Achieving a uniform body weight and frame size at 4 weeks of age is
an essential component to getting the flock off to the best possible start during this start-up
period. Males need to achieve the body weight standard each week for the first 4 weeks
of age. A longer ad libitum feeding period is recommended for males if they fail to achieve
the desired body weight at 28 days. Males should be grown separately from females for at
least the first 6 weeks of age, however complete sex-separate rearing to housing between
140-154 days is recommended for best results.
Provide adequate feeder space for males and females at all times taking into consideration the
flock age. Ideally, pullets should be reared with a minimum of 4.5” (11.50 cm) of feeder space
and males with a minimum of 6.0” (15.0 cm) from 4 weeks of age up to housing.
The feeding time should be consistent from day to day and feed should be distributed evenly
to all birds throughout the house in less than 3 minutes from the time the feeder starts. Adjust
feed hopper gates or feeder run times so that feed makes it around the house, or as far as
possible, to provide the most feeder space per bird. The feed trough or pan height should be
adjusted so that they rest on the litter during the first 14 days to ensure all birds can easily
access feed without having to climb into the feeder. Thereafter, feeders should be raised
incrementally throughout the growing period so that the lip of the trough or pan is level with
the birds’ back at all times. Weekly feed increases should be based on body weight targets.
COBB4

COBB 5
Continuous lighting should be provided for the first 48-72 hours post placement. Provide an
intensity of 20-60 lux (~2.0-6.0 ft. candles) for the first 7 days to help chicks find feed and water
more easily. It is highly recommended that all rearing houses be light tight with all flocks grown
under blackout conditions.
lighting management
0-3
4-7
8-14
14-28
23
16
12
8
2.0-6.0
2.0
1.0
0.5
20-60
20
10
5
Age Light Intensity
FC Lux
Hours
of LightDays
Blackout Rearing
Lighting Program (0-4 weeks)
*In the first 4 weeks, maintain adequate daylength
so the birds have time to consume the complete
amount fed.
Water has been called “the invisible player” in brooding issues and is an essential nutrient
that impacts virtually all physiological functions. It is essential to provide easy access to fresh
clean water so that feed intake and growth are maintained. Supplemental drinkers are highly
recommended at placement and should be provided at the rate of 1 per 100 chicks from day
old to 7 days. Preferably, mini drinkers, easy fills or one gallon chick fonts should be used
rather than open trays. Clip-on cups made for nipple drinker lines can be used, however for
best results these should be used in combination with easy fills or chick fonts for maximum
water consumption.
water management

COBB6
Supplemental water should be placed in the “Chick Comfort Zone” between feeders and close
to brooder stoves or the heat source for the first 3-5 days and then gradually removed. The
water temperature should be tepid (~80°F/26.7°C). Bio-degradable paper placed near the
water lines has been shown to help attract chicks to nipple drinkers resulting in chicks using
nipples more quickly after placement. In addition to the supplemental water source, chicks
should have access to the main drinking system at placement. Provided the proper water
pressure has been set, nipple activation should leave a small droplet of water at the tip of the
nipple to further stimulate the curiosity of the baby chick. Nipple drinkers should be installed
at the rate of 10-12 birds per nipple and birds should not have to travel more than 10 ft. (3 m)
to access water. They should be adjusted per the manufacture’s recommendations for height
and operating pressure. Generally the height of the nipple line should be at eye level for the
first 48-72 hours post placement. Begin raising nipple lines on the 4th day so birds are drinking
at a 45° angle.

COBB 7
From this time on raise lines up gradually so birds are drinking straight up by the 10th day.
While drinking, a bird’s feet should remain flat on the floor at all times.
Litter conditions are an excellent means of assessing the effectiveness of water system
settings. Damp litter under the water source indicates drinkers are set too low or pressure is
too high. Excessively dry litter under drinkers may indicate water pressure is too low or the
nipple line is too high for easy access. Nipple water line sight tubes should be kept clean at all
times and pressure adjustments should be made in small increments.
Monitoring water consumption through the use of water meters can be an excellent means
of gauging feed as there is a high correlation between feed and water consumption. Water
meters should be sized the same as the incoming water supply line to ensure adequate flow
rate. Water consumption should be evaluated at the same time each day to best determine
general performance trends and bird well-being. Any substantial change in water usage should
be investigated as this may indicate a water leak, health change or feed issue. A drop in water
consumption is often the first indicator of a flock problem.
Water consumption should equal approximately 1.6-2.0 times the feed intake by weight on a
daily basis at 70° F (21.1°C). Intake will vary based on environmental temperature, feed quality
and bird health. Erratic water intake fluctuations should be investigated before restricting water
availability, which should not be a standard practice.
According to research conducted by Viola et al. (2003), a 40% water restriction decreases the
feed intake (from 542 g to 338 g), body weight (from 471 g to 295 g) and FCR (up from 1.28
to 1.37) at 14 days. Water consumption for the first 24 hours should be approximately 24 mls.
(0.8 oz.)/bird.
DAY 1
WEEK 1
WEEK 1
WEEK 2
WEEK 2
WEEK 4
WEEK 4
& OLDER
Column
Pressure
or more
4in/10cm
Column
Pressure
6in/15cm
2in/5cm
Column
Pressure
4in/10cm
2in/5cm
Column
Pressure
2in/5cm
1in/2.5cm

COBB8
temperature management
Prior to chick placement, brooders and space heaters should be checked regularly to ensure
they are working correctly. House pre-heating should commence 24 to 48 hours prior to
placement depending on climatic and house conditions. Pre-heating ensures that the floor,
litter, water and air temperatures are ideal for baby chick placement.
The use of a brooder guard is recommended for the first 5-7 days to confine chicks to the
“Chick Comfort Zone”. Guards should be 14-18” (35-46 cm) high and made of 1” (2.5 cm).
mesh wire. Brooder guards generally run the full length of the house and should be removed
after the 7th day.
With pancake type brooders, the ideal floor temperature directly under the brooder is 105°F
(40.5°C), approximately the same temperature as the internal temperature of a brooding hen.
The floor temperature at the brooder edge should be in the range of 85-90°F (29-32°C).
With whole-house space heating, the ideal floor temperature should be at least 90°F (32°C).
Observe chicks and adjust for their comfort, making sure not to overheat. Chicks that become
overheated or chilled will experience problems such as pasting, unabsorbed yolks, stress
and dehydration. Good performance requires close monitoring and adjustment of brooder
temperatures and house ventilation to prevent these conditions from occurring. An excellent
indicator of floor temperature is the temperature of the chick’s feet. If the feet are cold, reevaluate
the heating system and litter temperature. If they are comfortably warm, the chicks should be
actively moving around the brooding area.
Pancake (jet) Brooders
Infrared (radiant) Brooders
Forced Air Furnaces
Maximum Density- Brooding
400-600 birds/ brooder
750-1000 birds/ brooder
21 birds/m2
(0.5 ft.2
/bird)

COBB 9
34.0
32.0
30.0
28.0
26.0
24.0
22.0
20.0
18.0
16.0
93.2
89.6
86.0
82.4
78.8
75.2
71.6
68.0
64.4
60.8
0
DegreesCelcius
DegreesFahrenheit
AGE (DAYS)
7 14 21 28 35
Temperature Guide
Age
(weeks)
Temperature at Brooder Edge
(2” above the litter)
Floor Temperature
at Brooder Edge
90 °F (32 °C)
85 °F (29 °C)
80 °F (27 °C)
75 °F (24 °C)
95 °F (35 °C)
90 °F (32 °C)
85 °F (29 °C)
80 °F (27 °C)
1
2
3
4
Measuring the Ambient Temperature
Ambient Brooding temperature profile for Cobb 500 parent breeders

COBB10
The internal chick temperature should be used as a guide to help determine if temperature
control is being managed properly.
Temperature can measured using a child’s ear thermometer.
Internal chick temperature guidelines include the following:
The internal temperature of the newly hatched chick should range from 40-41 ºC (104-
106 ºF), increasing to 41-42 ºC (106-108 ºF) during the 1st 5 days.
An internal chick temperature >41.0 ºC (106 ºF) will lead to panting.
An internal chick temperature <40.0 ºC (104 ºF) indicates the chick is too cold.
A comfortable chick will breathe through its nostrils and lose 1-2 g of moisture in the
first 24 hours.
The yolk also contains 1-2 g of moisture so the chick will lose weight but not become
dehydrated.
If chicks start panting they can lose 5-10 g of moisture in the first 24 hours and then
dehydration will occur.
Higher relative humidity will reduce moisture loss but also impair heat loss, so the
correct temperature is vital.
Chicks from smaller eggs (younger breeder flocks) require higher brooding temperatures
because they produce less heat.
The yolk contains 2/3 fat and 1/3 protein; fat for energy and the protein for growth.
The yolk content should be less than 10% of the total chick weight.
If early feed consumption doesn’t take place the chick will use both fat and protein in
the yolk for energy resulting in inadequate protein levels for growth.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

COBB 11
air quality and ventilation
In addition to proper temperature regulation, air quality and ventilation needs to be considered.
Ventilation distributes heat evenly throughout the house and maintains optimum air quality
in the brooding area. “Minimum ventilation” should begin with house preheating 24-48 hours
prior to placement to remove waste gases and moisture. Young birds are very susceptible to
drafts and air speeds as slow as 100 ft./min. (0.5 m/sec.) can create a significant wind-chill
effect on day old birds. Minimum ventilation practices should be employed to circumvent
inadvertent chilling up to 14 days of age.
Deﬁnition of Good Air Quality
Oxygen > 19.6%
Carbon dioxide < 0.3%/3000 ppm
Carbon monoxide < 10 ppm
Ammonia < 10 ppm
Inspirable Dust < 3.4mg/m3
Relative Humidity >< 45-65%
> No less than
< No more than
>< In between
**Minimum ventilation must be
increased if these parameters
are not being met.
Effects on Air Quality when Minimum Ventilation fans do not run
Minimum ventilation fans should be programmed to run on cycle timers (5 or 10 minute
cycles) with a thermostat override. They should be set to operate a minimum of 20% of the
total fan run time. As fan volume increases (or decreases), the inlet volume must react to
pressure changes in the same proportion as the fan capacity. Poor air quality during rearing
negatively affects pullet/ cockerel health and performance and can also have an adverse
effect on overall flock productivity in terms of egg production, livability, fertility and hatchability.
10 minutes
Ammonia 15 PPM 35 PPM 50 PPM 80 PPM
Carbon Dioxide 300 PPM 1500 PPM 2600 PPM 3500 PPM
Humidity 68 % 78 % 86 % 97 %
Temperature 68 ºF 75 ºF 82 ºF 88 ºF
15 minutes5 minutes0 minutesFan off time:
Air Quality
Air quality decreases rapidly when fans are off. This can potentially result in damage to the
respiratory and immune systems.
With CO2 levels above 1000ppm it is possible to see signs in the birds of reduced
activity and consumption reduction.

COBB12
ventilation guidelines
Tunnel ventilation should never be used prior to 28 days of age. Birds are never fully
feathered until after 28 days of age.
Air speed across the birds should be maintained as low as possible (< 40 fpm/0.3m/
sec) for the first 14 days. The “actual air temperature” should be the primary
consideration in determining the correct temperature setting.
From 15-21 days of age, air speed should not exceed 100 fpm (0.5m/sec). A
“transitional” ventilation system can be used and the “effective air temperature”
should be the primary consideration in determining the correct temperature setting.
From 22-28 days of age, air speed should not exceed 200 fpm (1m/sec). Again,
a “transitional” ventilation system can be used and the “effective air temperature”
should be the primary consideration in determining the correct temperature setting.
After 29 days of age, air speed does not have to be restricted and evaporative cooling
can be used if needed. The “effective temperature & the relative humidity” should be
the primary consideration in determining the correct temperature setting.
Chicken houses should never be ventilated to suit only the grower.
For management techniques for pullets or breeders raised in high altitudes
(above 800m/2,600 ft.) please contact your Cobb technical service representative
in your region.
1.
2.
3.
4.
5.
6 .
7.
For more detailed Air Quality & Ventilation information, refer to the Cobb Breeder
Management Guide.

COBB 13
Grading the Young Flock
Birds grow at different rates not only from their genetic potential but also due to acquired
eating temperament. The birds with more aggressive appetites will push the timid birds to
the side and consume more than their share at the expense of smaller birds.
This will continue and is especially detrimental when there are shortcomings in feeder space,
temperature, air and water quality, or feed delivery times. Grading of birds by bodyweight
is the best way to improve and maintain flock uniformity. The smaller birds graded into a
separate pen are the most timid ones and will always remain so. Because of this, they will
need to stay in pens with the other timid birds rather than be re-introduced into the general
population to be pushed aside again.
There are several grading programs practiced around the world, but all agree that grading
is best done as early in life as possible. Then this will have time to affect the frame size,
generally established before 4-5 weeks of age. Production results have been improved
by grading the flock by weight as early as 7 days and placing birds of similar weights into
separate pens. Using four groups seems to work the best: The medium group, which will be
the highest number, will have all birds plus or minus 10% of the average weight; the heavy
group, with chicks more than 10% heavier than the average; the light group, with birds 10
to 20% under the average; and the super-light group, with birds more than 20% under the
average weight.
The birds are then placed into different pens so they can be fed separately using the amount
and ration that best meets their needs. Smaller birds can be fed more of a higher density diet
early enough to give them the extra nutrients they need to catch up to the average birds in
the flock. The heavier birds can be fed the amount normally fed to the medium group, and
their growth rate will be controlled as they will only compete with like size birds.
Grading by weight can be carried out as needed to establish and maintain uniformity.
The first 4 weeks of a baby chick’s life is a critical time that contributes to the overall flock
productivity. At placement, baby chicks are entirely dependent on grower management for
survival. The objective of the brooding period is to create the ideal environmental conditions
where the chick does not have to make a choice. Grower attention to detailed management
is essential to accomplishing this objective.
SUMMARY

COBB14
NOTES

COBB 15
NOTES

L-1060-04
December 1, 2013
cobb-vantress.com

Brooding guide

More Related Content

What's hot (20)

Similar to Brooding guide (20)

Recently uploaded (20)

Brooding guide