Cadence plus installation manual
0 likes574 views
The installation manual for the iMovr Cadence Plus Sit-Stand Workstation provides detailed instructions for assembly, including weight capacity limits of 6.5-24.5 lbs, necessary tools, and part kits. It emphasizes the importance of adhering to installation warnings to prevent property damage or personal injury. The manual includes procedures for clamp and grommet mounting, adjustments for arm counterbalance and tray leveling, and monitor installation guidelines.
Cadence plus installation manual
- 1. INSTALLATION MANUAL iMovR CADENCE PLUS SIT-STAND WORKSTATION Weight Capacity: 6.5-24.5 lbs.
- 2. Contents Tools Required / Supplied Part Kits / Warnings/Disclaimers..........2 Base Installation Clamp Mount Base Location...............................................3 Grommet Mount Base Orientation.......................................4 Pivot Limiter Installation............................................................4 Attaching the Arm to the Base...................................................5 Installing Work Surface.............................................................5 Installing Keyboard Tray............................................................5 Keyboard Tilt............................................................................6 Keyboard Storage Stop ............................................................6 Installing Monitor......................................................................6 Cable Management Installation..................................................7 Arm Counterbalance Adjustments..............................................7 Tray Leveling Adjustments (Left to Right)....................................8 Monitor Adjustments.................................................................8 Monitor Tilt Tension Adjustment.................................................8 INSTALLATION WARNINGS: • Read the entire instruction manual before beginning any installation or assembly. • The installer must verify that the attachment surface can safely support the combined weight of all the attached equipment and hardware. • Improper installation of this product may cause extensive property damage or serious personal injury, either during or after installation. DISCLAIMERS: • The manufacturer will bear no responsibility for any damages of any kind arising from improper installation of this product. • In no way will the manufacturer be held liable for any damage to the monitor, property or personal injury should an outside force either intentionally or unintentional be applied to the monitor or monitor mounting bracket ADJUSTMENT NOTIFICATIONS: • Routine maintenance checks and adjustments are suggested to properly support the quality and optimal performance of this product. Refer to adjustment suggestions on last page of booklet, or contact your distributor for further detailed information. • Over tightening of bolts during installation or adjustments can damage the product and affect the function and warranty. Allen Keys, 1/8",3/16", 7/32",1/4" 3/8" Wrench (for Dual Monitor option) Tools Required Supplied Part Kits #2 Phillips Screwdriver Level Warnings/Disclaimers KIT A: Arm Bolt/Washer Kit KIT C: VESA Mounting Plate Kit KIT B: Grommet Mounting Bolt Kit 2 Installation Manual: CADENCE PLUS SIT-STAND WORKSTATION KIT D: Tray Hardware Kit
- 3. The unit can be installed on a 24" or 30" deep rectangular or corner desk using the integral desk clamp or grommet mounting hardware provided. Base Installation Clamp Mount Base Location Determine desired installed tray location. Offset base location by 13" left or right for a 24" deep desk or centered for a 30" deep desk. Slide the angle bracket assembly onto the back of the desk. Secure the clamp plate to the underside of the desk with the supplied bolts. Use a 7/32" Allen Key to tighten to 75 in-lbs. To reverse the bottom clamp, remove the three screws using a 3/16" Allen Key and reinstall the Bottom Clamp in the DOWNWARD position. Slide the angle bracket assembly onto the back of the desk. Secure the clamp plate to the underside of the desk with the supplied bolts. Use a 7/32" Allen Key to tighten to 75 in-lbs. Bottom Clamp is UPWARD. Bottom Clamp is DOWNWARD. DESK THICKNESS - 3/4" - 1 1 /2" DESK THICKNESS - 1 1 /2" - 2 1 /2" Installation Manual: CADENCE PLUS SIT-STAND WORKSTATION 3 13" 13" 24" DEEP DESK 30" DEEP DESK STEP 1 STEP 2 The thickness of the desk will determine the orientation of the bottom clamp. The product comes pre-configured for a 3/4" - 1 1 /2" desk. Bottom Clamp Bottom Clamp Angle Bracket Angle Bracket Clamp Plate Clamp Plate
- 4. Grommet Mount Base Orientation If installer is drilling their own hole, ensure that the diameter is a minimum of 1/2". STEP 1 STEP 2 STEP 3 4 Installation Manual: CADENCE PLUS SIT-STAND WORKSTATION Make sure the pin remains engaged in the arm base when the arm is attached to the desk mount base. Pivot Limiter Installation Tighten the bolt securely under the desk using a 7/32" Allen Key to 75 in-lbs. Detach the angle bracket assembly (not used in a grommet application) by removing the 4 screws with a 7/32" Allen Key. Insert the grommet bolt through the washer (KIT B: Grommet Mounting Bolt) and upward facing clamp plate. From under the desk insert the grommet bolt assembly through the desk into the center hole of the base. PIVOT LIMITER VIEW FROM UNDERSIDE Lightly tap the pin to ensure it stays in place during installation. The pin should only protrude 1/4" once fully seated. ALLOWS 180° ROTATION Position pin at 12:00 to prevent the arm from coming in direct contact with the wall on either side 180°
- 5. With the base already installed on the desk. Attaching the Arm to the Base STEP 1 Slide the large nylon washer (KIT A: Arm Bolt/Washer Kit) over the bottom pin of the arm. STEP 2 Set the main arm bottom pin into the base. STEP 3 While holding the arm in the lowest position remove the trim cap at the back of the arm. STEP 4 Hold the arm in the lowest position to prevent it from springing up, insert the bolt/washer assembly (KIT A: Arm Bolt/Washer Kit) through the back of the arm and into the base. Ensure the washers are as illustrated. STEP 5 Keeping the arm down tighten the bolt with a 1/4" Allen Key until the bolt is seated and snug. Tighten or loosen bolt to obtain desired resistance for left to right arm movement. STEP 6 Replace the trim cap at the back of the arm. STEP 5 STEP 6 STEP 4 Use two-sided Hook and Loop pads to secure keyboard to tray. (KIT C: VESA Mounting Plate Kit) NOTE: Ensure nylon bushing is on the arm post when inserting the arm into the base. Installation Manual: CADENCE PLUS SIT-STAND WORKSTATION 5 Do not overtighten bolt as this may cause damage to the product. ! STEP 2 STEP 1 STEP 4 STEP 3 Plastic Steel Installing Work Surface Position the work surface on the tray support arm aligning the tray in the desired position and secure with four flat head screws (KIT D: Tray Hardware Kit). Use 1/8” Allen Key to secure. Note, work surface can be mounted forward on the tray support by using the front four thru holes on the tray support neck, and the back four threaded holes on the work surface bracket. Installing Keyboard Tray STEP 1 Slide the keyboard tray head assembly into place as shown. STEP 2 Insert the Hex screw into the threaded hole of the keyboard tray head and tighten with 3/16" Allen Key until snug. Releasing and securing the Hex screw will allow for independent keyboard tray height adjustment. STEP 1 STEP 2 18.759 STEP 3 Place the keyboard tray on the tray head. Secure with four flat head screws and nuts (KIT D: Tray Hardware Kit). Use 1/8” Allen Key to secure. SIDEVIEW OF ASSEMBLY Use the Hex head screw from (Kit D: Tray Hardware kit)
- 6. For this step, the installer needs to determine if they wish to use the Quick Connect adapter supplied or mount the monitor directly to the VESA mount on the monitor tower. Installing Monitor (6.5 lbs. to 24.5 lbs.) SINGLE-MONITOR If using the Quick Connect adapter, mount the Quick Connect adapter (Kit C: VESA Mounting Plate Kit) to back of the monitor with the screws provided. Use a #2 Phillips screwdriver to secure screws. Lift monitor into position and slide the Quick Connect onto the VESA. If not using the Quick Connect adapter, mount the monitor directly to the VESA mount on the monitor tower with the screws provided. Use a #2 Phillips screwdriver to secure. DUAL-MONITOR (Optional Dual Monitor Kit) Attach the dual bracket to the monitor tower VESA with the hardware provided in the Dual Monitor Kit. To attach monitors see steps for single-monitor. NOTE: Adjustable bracket supports most 24" monitors weighing up to 10 lbs. each. 6 Installation Manual: CADENCE PLUS SIT-STAND WORKSTATION Keyboard Tilt (+5° to -15°) Keyboard Storage Stop To adjust the tray angle, place tray in desired tilt position and adjust front set screw with the 1/8" Allen Key. To adjust the maximum storage angle, place tray in the maximum storage location and tighten rear set screw with the 1/8" Allen Key.
- 7. After the technology has been installed, ensure there is enough slack in the cables from the monitor, keyboard and mouse along with any other peripherals. Arm adjustment is to be made after all technology has been installed from 6.5 lbs. to 24.5 lbs. Cable Management Installation Arm Counterbalance Adjustments ATTENTION: Arm must be held down to perform this adjustment. STEP 1 Remove the trim cap at the back of the arm. STEP 2 Keeping the arm down, use a 1/4" Allen Key to turn the middle bolt at the back of the arm. Turning the bolt CLOCKWISE decreases the spring force reducing the counter balance load. Turning the bolt COUNTERCLOCKWISE increases the spring force increasing the counter balance load. STEP 3 Adjust the middle bolt until the arm counter balance is acceptable. STEP 4 Replace the trim cap at the back of the arm. + –+ – – +– COUNTERBALANCE ADJUST Do not overtighten bolt as this may cause damage to the product. ! 1/4" Allen Key STEP 2 & 3 STEP 1 & 4 Installation Manual: CADENCE PLUS SIT-STAND WORKSTATION 7 STEP 1 Locate the two cable management clips under the arm. Gently open each of the clips. STEP 2 Place all required technology cables (power cord, mouse cable, VGA etc.) through the clips under the monitor arm. Make sure to leave enough slack in the cables to allow the arm to move freely. STEP 3 Gently close the clips to secure the cables in place. Re-adjust slack in the cables if necessary. A
- 8. Tray adjustment is to be made after all technology has been installed. Tray Leveling Adjustments (Left to Right) STEP 1 Remove the trim cap at the back of the arm. STEP 2 Keeping the arm down, use the 3/16" Allen Key to turn the top bolt at the back of the arm. Turn the bolt until the tray is level. STEP 3 Confirm that surface is level with spirit level. STEP 4 Replace the trim cap at the back of the arm. + –+ – + – +– LEVEL ADJUST 3/16" Allen Key STEP 3 STEP 2 Monitor Tilt Tension Adjustment Monitor Height Adjustments STEP 1 To adjust the monitor tilt tension, use a 3/16" Allen Key to adjust the tension setting on both sides of the VESA plate. Setting number 1 is for light monitors and 4 is for heavier monitors. The factory default setting is 1. STEP 2 Adjust the setting screw until a desirable tension is achieved. Hold and support the monitor before loosening the monitor tower knob. Turn the monitor tower knob counterclockwise to loosen. Move the monitor to desired location. Turn the monitor tower knob clockwise to tighten. STEP 4 Do not over rotate the dial beyond “1” or “4” position or possible damage to the dial may occur.! + – + – + – + – + – + – 1. Adjust tension as necessary 2. Repeat on alternate side Light monitor Heavy monitor 1 2 3 4 1 2 3 4 ATTENTION: Tray must be parallel to the work surface and swiveled 90° to the base when adjusting. + – + – + – + – + – + –