Camden CM-310 Instruction Manual
0 likes351 views
The document provides installation instructions for the CM-310EE Exit Switch & Integrated Timer. The switch has a 30 second timer and illuminated push button for easy exit. It is designed to release a magnetic lock per fire code standards. The unit has a double break circuit to ensure the lock releases even if the timer fails. Installation involves mounting the switch plate and wiring the six colored leads to power and the magnetic lock according to the provided diagram.
Camden CM-310 Instruction Manual
- 1. CM-310EE Exit Switch & Integrated Timer (Ver. 2) Installation Instructions Section 1 __________________ General Description Camden model CM-310EE is an illuminated Exit switch incorporating a 30 second timer. The stainless steel faceplate is designed to flush mount on to a 1 ¾” wide doorjamb. The ½” x ¾” rectangular translucent button is easy to push. CM-310EE model is supplied with a 12V AC/DC incandescent light bulb, which is accessed through the front of the switch. If the unit is powered 24VDC, the supplied in-line resistor must not be removed. This switch has been designed specifically to release a magnetic lock from the inside, as per the BOCA code. When the button is pushed and released, the lock will release for 30 seconds. Re-trigger is possible at any time. The “double break” circuitry has been designed so that even if the timer fails, depressing the switch will interrupt power to the magnetic lock. Section 2__________________ Installation Mounting The unit is completely pre-wired for easy installation. Connect the appropriate wires to your devices as per the enclosed wiring diagram. Tuck wiring into box (retrofit box included), and fasten switch plate using screws provided. Wiring Six color coded leads are provided. This unit will operate on 12 or 24 VDC, with no jumper change required. For convenience it may be powered by the same power that supplies the magnetic lock. The two pairs of Red & Black wires connect to 12 or 24 VDC. One pair supplies power to the timer, and the other pair powers the light. The internal timer and the push button are connected in series with the Green & White wires. This is how the “double break” feature works. Therefore, the unit must be wired as shown. The Green wire goes to the positive input wire of the magnetic lock, and the White wire goes to a source of + Voltage. Please refer to the enclosed wiring diagram for typical hook-up. Important CM-310EE models have a connected lead wire with black-colored heat shrink (over an in-line resistor). If powered 24V; Do not remove in-line resistor If powered 12V; Cut (remove) in-line resistor Section 3 _________________ Technical Data Lens Color Green lens Legend Push to Exit Size 4.5”h x 2.75”w x 2.5”d Mounting 2 x #6-32 machine screws Operating voltage 12 / 24 Volts DC Time Delay 30 seconds Contact Rating 4 amps @ 30 VDC Incandescent Bulb Life 15,000hrs.@ rated capacity Section 4_________________ Limited Warranty Camden Door Controls Inc. warrants this product to be free from defects for 3 years from date of manufacturing. Visit our web site at www.camdencontrols.com to see our complete warranty policy, including limitations and the procedures for product returns. Questions? Call us toll-free at 1-877-226-3369
- 2. FILENAME: CM-310EE Diagram.vsdDRAWING No: DRG-CM310EE-031703 CM-310EE Egress Switch Wiring Diagram (Ver 2.0) SCALE: NONE DRAWN BY: DGW REVISED: 03/20/12DATE: 03/18/03 Camden Door Controls 5502 Timberlea Blvd. Mississauga, Ontario L4W 2T7 12 / 24 VDC Power "-" Wire White to "+" 12 / 24 VDC, or, through Relay of Motion Detector (optional) White Green Red Rear View of CM-310EE switch and Faceplate NOTES: 1. For 12V operation, cut off inline-resistor (on Red bulb wire only). For 24V operation, leave inline resistor in place. 2. Bulb Replacement. Access to light bulb is obtained by first removing front rectangular lens with a thin blade screwdriver. Then, using a pair of needle-nose pliers, carefully pull light bulb straight out. Re-installation is reverse of above sequence. Be sure to line up both pins before pushing bulb in. Red Black Black Motion Detector "+" Power In Relay Out + - O p t i o n a l M o t i o n Detector shown. If not used, wire White to Positive Terminal of power supply. Magnetic Lock (Light) (Light)Inline Resistor* Note: CM-310EE models have a connected lead wire with black-colored heat shrink (over an in-line resistor). If powered 24V; Do not remove in-line resistor If powered 12V; Cut (remove) in-line resistor