Ccie security
1 like994 views
This document provides an overview and introduction to the CCIE Security Exam Certification Guide written by Henry Benjamin. It discusses that the guide is designed to provide information to help readers prepare for and pass the CCIE Security written exam. It also provides publishing details such as the copyright, publisher information, and biographical information about the author Henry Benjamin and his experience and qualifications.
![xxi
Command Syntax Conventions
Command syntax in this book conforms to the following conventions:
• Commands, keywords, and actual values for arguments are bold.
• Arguments (which need to be supplied with an actual value) are in italics.
• Optional keywords and arguments are in brackets [].
• A choice of mandatory keywords and arguments is in braces {}.
Note that these conventions are for syntax only.
Conclusion
Having many Cisco certifications myself, the joy and success I have achieved has significantly changed my
life and that of my family. There are always challenges facing network engineers and, no doubt, becoming a
certified Cisco professional meeting those challenges will drive you into acquiring skills you thought you
never knew you could master.
I sincerely hope you enjoy your time spent with this book; it took over six months and long nights to com-
plete to ensure you have the perfect companion through your journey to becoming CCIE certified.
When you succeed in attaining your certification, feel free to e-mail me at hbenjamin@optusnet.com.au so
I, too, can enjoy your success.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-22-320.jpg)
![18 Chapter 2: General Networking Topics
28 A Cisco router has the following route table:
R1#show ip route
131.108.0.0/16 is variably subnetted, 17 subnets, 2 masks
C 131.108.255.0/24 is directly connected, Serial0/0
C 131.108.250.0/24 is directly connected, Serial0/1
O 131.108.254.0/24 [110/391] via 131.108.255.6, 03:33:03, Serial0/1
[110/391] via 131.108.255.2, 03:33:03, Serial0/0
R 131.108.254.0/24 [120/1] via 131.108.255.6, 03:33:03, Serial0/1
[120/1] via 131.108.255.2, 03:33:03, Serial0/
What is the preferred path to 131.108.254.0/24? (Choose the best two answers.)
a. Via Serial 0/0
b. Via Serial 0/1
c. None
d. To null0
29 IP RIP runs over what TCP port number?
a. 23
b. 21
c. 69
d. 520
e. None of the above
30 IP RIP runs over what UDP port number?
a. 23
b. 21
c. 69
d. 520
31 An OSPF virtual link should .
a. Never be used
b. Allow nonpartitioned areas access to the backbone
c. Allow partitioned areas access to the backbone
d. Not be used in OSPF, but in ISDN](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-41-320.jpg)
![28 Chapter 2: General Networking Topics
Table 2-2 Ethernet Media Formats
Media Type Characteristics
10Base5 Maximum length: 500 m
Maximum stations: 1024
Speed is 10 Mbps
Minimum distance between devices is 2.5 m
10Base2 Maximum length: 185 m, using RG58 cable types and T connectors on all end
stations
Minimum distance between devices is 0.5 m
Maximum devices per 185-m segment is 30 stations
Speed is 10 Mbps
10BaseT Based on UTP cabling
Up to 100 m, better category cables longer
One device per cable. Typically, only one device per segment with hubs or
switches connecting all devices together
Speed is 10 Mbps
Physical topology star, logical topology bus
100BaseT Same characteristics as 10BaseT but operates faster, at 100 Mbps
Can be fibre, as well (100BaseFx); defined in IEEE 802.3U
Physical topology star, logical topology bus
1000 GE Gigabit Ethernet operating at 1000 Mbps
Can run over fibre or UTP; frame formats and CSMA/CD identical to Ethernet
standards
Physical topology star, logical topology bus
* The word BASE refers to Baseband signaling, which uses a single channel, as opposed to broadband, which uses
multiple frequency channels.
Switching and Bridging
This sections covers Layer 2 devices that are used to bridge or switch frames using common
techniques to improve network utilization, such as VLANs. The terms switch and bridge are
used to mean the same technology.
Switching, or bridging, is defined as a process of taking an incoming frame from one interface
and delivering it through another interface. Source stations are discovered and placed in a
switch address table (called content-addressable memory [CAM] table in Cisco terms). Routers](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-51-320.jpg)
![Ethernet Overview 29
use Layer 3 switching to route a packet, and Layer 2 switches use Layer 2 switching to forward
frames.
Switches build CAM tables when activity is noted on switch ports. Example 2-1 displays a
sample CAM table on a Cisco Catalyst 5000 switch.
Example 2-1 CAM Table or Bridge Table
CAT5513 (enable) show cam ?
Usage: show cam [count] <dynamic|static|permanent|system> [vlan]
show cam <dynamic|static|permanent|system> <mod_num/port_num>
show cam <mac_addr> [vlan]
show cam agingtime
show cam mlsrp <ip_addr> [vlan]
CAT5513 (enable) show cam dynamic
* = Static Entry. + = Permanent Entry. # = System Entry. R = Router Entry. X = P
ort Security Entry
VLAN Dest MAC/Route Des Destination Ports or VCs / [Protocol Type]
---- ------------------ ----------------------------------------------------
36 00-10-7b-54-37-c6 8/13 [ALL]
35 00-09-43-3b-ac-20 8/5 [ALL]
101 00-01-02-00-4a-ff 1/1 [ALL]
1 00-01-02-00-4a-ff 1/1 [ALL]
102 00-03-e3-5e-ac-81 1/1 [ALL]
101 00-00-0c-92-0c-af 1/1 [ALL]
102 00-03-e3-53-7f-81 1/1 [ALL]
102 00-03-e3-5e-ae-c1 1/1 [ALL]
37 00-03-e3-63-55-80 8/9 [ALL]
102 00-03-e3-5e-a9-01 1/1 [ALL]
Example 2-1 displays a CAM table on a Catalyst switch with the CatOS command show cam
dynamic. You can use other CatOS commands to view specific ports (show cam dynamic 8/13
would show only devices discovered on port 8/13). Example 2-1 displays that the MAC address
01-10-7b-54-37-c6 is located via the port 8/13.
A Cisco switch populates the CAM tables as new devices send frames, so a switch bases all
bridging decisions on source MAC address. When a device first sends a frame to a connected
port on a switch, the switch adds the incoming source address to the CAM table. Any broadcasts
received because the switch has no CAM entry are sent out all ports except the port the frame
was received on. The switch then adds the source MAC address on the source port. Frames that
are received as broadcasts are sent out all ports active in spanning tree.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-52-320.jpg)
![TCP Services 49
on the Ethernet share the segment labeled San Jose network. To take advantage of the two rout-
ers, HSRP will allow only Routers C and D to bid for a virtual IP address, and if any one router
(Router C or D, in this example) fails, the operational router assumes the HSRP gateway
address. Host devices typically have only a brief 100 to –200-millisecond interruption when
a network failure occurs.
To illustrate how HSRP provides default gateway support, refer to Figure 2-12. In Figure 2-12,
you can see a network with two local routers configured with an Ethernet interface address of
131.108.1.2/24 for Router C and 131.108.1.3/24 for Router D. Notice that both routers share a
common Ethernet network. Assume that PC1 has been configured with a default gateway point-
ing to Router C. If Router C goes down or the Ethernet interface becomes faulty, all the devices
must be manually reconfigured to use the second default gateway (Router D, 131.108.1.3/24).
HSRP enables the network administrator to elect one of the two routers to act as the default
gateway. If the elected router goes down, the second router assumes the IP default gateway. The
IOS command standby track interface-of-wan under the Ethernet interface allows the router
to monitor the WAN link. If the WAN link continuously fails past a threshold, the HSRP default
router will decrease its priority to allow a more reliable WAN connection to provide a gateway.
For example, in Figure 2-12, if the link between Routers C and B fails past a threshold, Router
D can be configured to assume the HSRP address to provide a faster connection to the IP back-
bone network.
The steps to enable HSRP are as follows:
Step 1 Enable HSRP (required).
Step 2 Configure HSRP group attributes (optional).
Step 3 Change the HSRP MAC refresh interval (optional).
Table 2-5 illustrates the various required and optional commands to enable HSRP.
Table 2-5 HSRP Commands
IOS Command Purpose
standby [group-number] timers [msec] These required commands configure the time
hellotime [msec] holdtime between hello packets and the hold time before other
routers declare the active router to be down.
standby [group-number] priority priority Sets the Hot Standby priority used in choosing the
[preempt [delay [minimum | sync] delay]] active router. The priority value range is from 1 to
or 255, where 1 denotes the lowest priority and 255
denotes the highest priority. Specifies that if the local
standby [group-number] [priority priority] router has priority over the current active router, the
preempt [delay [minimum | sync] delay] local router should attempt to take its place as the
active router. Configures a preemption delay, after
which the Hot Standby router preempts and becomes
the active router. These commands are optional.
continues](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-72-320.jpg)
![50 Chapter 2: General Networking Topics
Table 2-5 HSRP Commands (Continued)
IOS Command Purpose
standby [group-number] track type number This optional command configures the interface to
[interface-priority] track other interfaces so that if one of the other
interfaces goes down, the device’s Hot Standby
priority is lowered.
standby [group-number] authentication Selects an authentication string to be carried in all
string HSRP messages. Optional authenticator field allows
only authenticated routers to offer HSRP.
standby use-bia [scope interface] Configures HSRP to use the burned-in address of an
interface as its virtual MAC address instead of the
preassigned MAC address (on Ethernet and FDDI),
or the functional address (on Token Ring).
Now configure Routers C and D in Figure 2-12 for HSRP, and ensure that Router C is the pri-
mary gateway address and that the PC is configured with a gateway address of 131.108.1.100.
Router C is configured with a higher priority (standby priority 110 preempt than the default
standby preempt)
100 to ensure Router C becomes the default gateway for the hosts on the San Jose network;
authentication is also enabled between the two gateway routers.
Example 2-5 displays the sample IOS configuration for Router C.
Example 2-5 HSRP Configuration on Router C
interface Ethernet0
ip address 131.108.1.2 255.255.255.0
standby priority 110 preempt
standby authentication cisco
standby ip 131.108.1.100
standby track Serial0
Example 2-5 displays Router C configured with a virtual IP address of 131.108.1.100 and
preempt, which allows Router C to assume the role if a failure occurs. The track command
ensures that Serial0, or the WAN link to Router B, is monitored to make sure a flapping link
does not cause bandwidth delays for users, such as PC1. For every tracked interface failure,
the priority is reduced by 10 by default. The Cisco IOS default priority is set to 100. In
this configuration, two failures must occur for Router D to assume the HSRP address
(110–10–10=90<100).
Example 2-6 displays the sample IOS configuration for Router D. Configure Router D with
an HSRP priority of 105 so that any one (1 not 2) failure on Router C will mean that Router D
priority is higher than Router C. (Router C is set to 105; one failure and then it is set to
105–10=95<100.)](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-73-320.jpg)
![54 Chapter 2: General Networking Topics
Routing is a process whereby a path to a destination host is selected by either a dynamic or static
routing protocol. A routing protocol is an algorithm that routes data across the network. Each
router makes routing decisions from host to destination based on specific metrics used by the
operating routing protocol. For example, RIP uses hop count (commonly known as the network
diameter) to decide what router interface the data is sent. A lower hop count is always preferred.
OSPF, on the other hand, uses a cost metric; the lower the cost, the more preferred a path to the
destination.
Routing IP across a network of Cisco routers requires IP address allocation to interfaces and
then a static or dynamic routing protocol to advertise these networks to local or remote routers.
After these networks are advertised, IP data can flow across the network. Routing occurs at
Layer 3 (the network layer) of the OSI model.
By default, IP routing is enabled on Cisco routers. The command used to start or disable IP
routing is [no] ip routing. By default, IP routing is enabled so you will not see this command
by viewing the configuration. Consider a one-router network with two directly connected
Ethernet interfaces as an introductory example. Figure 2-13 displays a two-port Ethernet router
configured with two subnets.
Figure 2-13 Connected Routes
Directly Connected Networks
172.108.1.1/24 R1 172.108.2.1/24
E0 E1
PC 1 PC 2
R1# show ip route
Codes C- connected, S- static, I- IGRP, R- RIP, M- mobile, B- BGP
D- EIGRP, EX- EIGRP external, Q- QSPF, 1A- OSPF inter area
N1- OSPF NSSA external type 1, N2- OSPF NSSA external type 2
E1- OSPF external type 1, E2- OSPF external type 2, E- EGP
i- IS-IS, L1- IS-IS level-1, L2- IS-IS level-2.*-candidate default
U- per-user static route, o- ODR
-
Gateway of last resort is not set
-
172.108.0.0/24 is subnetted, 2 subnets
C 172.108.1.0 is directly connected, Ethernet0
C 172.108.2.0 is directly connected, Ethernet1
R1#
PC1 can communicate with PC2 as shown in Figure 2-13, because Cisco routers will route to
directly connected interfaces.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-77-320.jpg)
![56 Chapter 2: General Networking Topics
Table 2-7 show ip route Defined* (Continued)
Field Description
172.108.0.0/24 is subnetted, 2 subnets Indicates the address of the remote network.
C 172.108.1.0 is directly connected, Ethernet0
C 172.108.2.0 is directly connected, Ethernet1
R1#
[160/5] The first number in the brackets is the
information source’s administrative
distance; the second number is the metric
for the route.
via Specifies the address of the next router to
the remote network.
0:01:00 Specifies the last time the route was updated
in hours:minutes:seconds.
Ethernet0 Specifies the interface through which the
specified network can be reached.
* Part of this table taken from
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fiprrp_r/ind_r/1rfindp2.htm#102251,
all rights are reserved to Cisco.
By default, Cisco IOS assigns each routing protocol an administrative distance (AD) that
indicates the trustworthiness of a routing entry if there is more than one path to a remote
network running two or more routing algorithms. You can configure the AD value from the
default with the distance administrative-distance IOS command if you want to manually
choose RIP over OSPF, for example. The value for administrative-distance can be 1 to 255.
Table 2-8 displays the administrative distances enabled by default on Cisco routers.
Table 2-8 Default Administrative Distances
Route Source Default Distance
Connected interface (or static route via a 0
connected interface)
Static route 1
Enhanced IGRP summary route 5
External BGP 20
Internal enhanced IGRP 90
IGRP 100](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-79-320.jpg)
![60 Chapter 2: General Networking Topics
Figure 2-14 Practical Example of Routing RIP
131.108.3.0/30
Frame Relay
172.108.1.1/24 172.108.2.1/24
E0/0 S0/0 S0/0 E0/0
R1 .1 .2 R2
R1's Loopbacks R2's Loopbacks
Loopback0 131.108.4.1/24 Loopback0 131.108.7.1/24
Loopback1 131.108.5.1/24 Loopback1 131.108.8.1/24
Loopback2 131.108.6.1/24 Loopback2 131.108.9.1/24
Example 2-10 displays the RIP configuration on R1. The same configuration commands are
applied to R2.
Example 2-10 IP RIP Configuration on R1
router rip
version 2
network 131.108.0.0
View the RIP forward database with the command, show ip rip database.
Example 2-11 displays the output when show ip rip database is executed on R1.
Example 2-11 show ip rip database Command on R1
R1#show ip rip database
131.108.0.0/16 auto-summary
131.108.1.0/24 directly connected, Ethernet0/0
131.108.2.0/24
[1] via 131.108.3.2, 00:00:12, Serial0/0
131.108.3.0/30 directly connected, Serial0/0
131.108.4.0/24 directly connected, Loopback0
131.108.5.0/24 directly connected, Loopback1
131.108.6.0/24 directly connected, Loopback2
131.108.7.0/24
[1] via 131.108.3.2, 00:00:12, Serial0/0
131.108.8.0/24
[1] via 131.108.3.2, 00:00:12, Serial0/0
131.108.9.0/24
[1] via 131.108.3.2, 00:00:12, Serial0/0](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-83-320.jpg)
![Routing Protocols 61
Example 2-11 displays the directly connected routers and the four dynamically discovered
routers via Serial0/0 to R2. To confirm that the entries are reachable, display the IP routing table
on R1 and perform a few ping requests across the Frame Relay cloud.
Example 2-12 displays the IP routing table and the successful ping requests to the four remote
networks.
Example 2-12 show ip route and ping to R2
R1#show ip route
Codes: C - connected, R - RIP,
131.108.0.0/16 is variably subnetted, 9 subnets, 2 masks
R 131.108.9.0/24 [120/1] via 131.108.3.2, 00:00:00, Serial0/0
R 131.108.8.0/24 [120/1] via 131.108.3.2, 00:00:00, Serial0/0
R 131.108.7.0/24 [120/1] via 131.108.3.2, 00:00:00, Serial0/0
C 131.108.6.0/24 is directly connected, Loopback2
C 131.108.5.0/24 is directly connected, Loopback1
C 131.108.4.0/24 is directly connected, Loopback0
C 131.108.3.0/30 is directly connected, Serial0/0
R 131.108.2.0/24 [120/1] via 131.108.3.2, 00:00:01, Serial0/0
C 131.108.1.0/24 is directly connected, Ethernet0/0
R1#ping 131.108.2.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 131.108.2.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms
R1#ping 131.108.7.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 131.108.7.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms
R1#ping 131.108.8.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 131.108.8.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms
R1#ping 131.108.9.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 131.108.9.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms
R1#
Example 2-12 displays the four remote networks reachable by the Serial 0/0 and four successful
ping requests (five replies to each remote network) to those interfaces on R2.
Stop R2 from sending R1 any updates via the Frame cloud to demonstrate the passive-interface
command, passive-interface Serial0/0.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-84-320.jpg)
![Routing Protocols 65
Example 2-16 show ip route on R1 (Continued)
D 131.108.9.0/24 [90/10639872] via 131.108.3.2, 00:04:27, Serial0/0
D 131.108.8.0/24 [90/10639872] via 131.108.3.2, 00:04:27, Serial0/0
D 131.108.7.0/24 [90/10639872] via 131.108.3.2, 00:04:27, Serial0/0
C 131.108.6.0/24 is directly connected, Loopback2
C 131.108.5.0/24 is directly connected, Loopback1
C 131.108.4.0/24 is directly connected, Loopback0
C 131.108.3.0/30 is directly connected, Serial0/0
D 131.108.2.0/24 [90/10537472] via 131.108.3.2, 00:04:28, Serial0/0
C 131.108.1.0/24 is directly connected, Ethernet0/0
Example 2-16 displays four remote EIGRP entries (designated by D in the routing table) via the
Serial interface Serial0/0. EIGRP has discovered these networks as the preferred path because
the WAN bandwidth is 256 kbps as opposed to 128 kbps via Serial 0/1. To view the alternate
paths, use the show ip eigrp topology IOS command to display backup paths.
Example 2-17 displays the output of the show ip eigrp topology command on R1.
Example 2-17 show ip eigrp topology on R1
R1#show ip eigrp topology
IP-EIGRP Topology Table for AS(100)/ID(131.108.6.1)
Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,
r - reply Status, s - sia Status
P 131.108.10.0/30, 1 successors, FD is 2169856
via Connected, Serial0/1
via 131.108.3.2 (11023872/1761792), Serial0/0
P 131.108.9.0/24, 1 successors, FD is 2297856
via 131.108.3.2 (10639872/128256), Serial0/0
via 131.108.10.2 (20640000/128256), Serial0/1
P 131.108.8.0/24, 1 successors, FD is 2297856
via 131.108.3.2 (10639872/128256), Serial0/0
via 131.108.10.2 (20640000/128256), Serial0/1
P 131.108.7.0/24, 1 successors, FD is 2297856
via 131.108.3.2 (10639872/128256), Serial0/0
via 131.108.10.2 (20640000/128256), Serial0/1
P 131.108.6.0/24, 1 successors, FD is 128256
via Connected, Loopback2
P 131.108.5.0/24, 1 successors, FD is 128256
via Connected, Loopback1
P 131.108.4.0/24, 1 successors, FD is 128256
via Connected, Loopback0
P 131.108.3.0/30, 1 successors, FD is 2169856
via Connected, Serial0/0
via 131.108.10.2 (21024000/1761792), Serial0/1
P 131.108.2.0/24, 1 successors, FD is 2195456
via 131.108.3.2 (10537472/281600), Serial0/0
via 131.108.10.2 (20537600/281600), Serial0/1
P 131.108.1.0/24, 1 successors, FD is 281600
via Connected, Ethernet0/0](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-88-320.jpg)
![Routing Protocols 75
Example 2-19 R2’s OSPF Configurations (Continued)
network 131.108.10.0 0.0.0.255 area 1
network 131.108.11.0 0.0.0.255 area 1
network 131.108.12.0 0.0.0.255 area 1
network 131.108.13.0 0.0.0.255 area 1
network 131.108.14.0 0.0.0.255 area 1
network 131.108.15.0 0.0.0.255 area 1
network 131.108.255.0 0.0.0.3 area 0
network 131.108.255.4 0.0.0.3 area 0
end
Example 2-20 displays the IP OSPF routing table on R1.
Example 2-20 show ip route ospf on R1
R1#show ip route ospf
131.108.0.0/16 is variably subnetted, 17 subnets, 2 masks
O 131.108.15.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1
[110/391] via 131.108.255.2, 00:00:41, Serial0/0
O 131.108.14.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1
[110/391] via 131.108.255.2, 00:00:41, Serial0/0
O 131.108.13.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1
[110/391] via 131.108.255.2, 00:00:41, Serial0/0
O 131.108.12.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1
[110/391] via 131.108.255.2, 00:00:41, Serial0/0
O 131.108.11.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1
[110/391] via 131.108.255.2, 00:00:41, Serial0/0
O 131.108.10.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1
[110/391] via 131.108.255.2, 00:00:41, Serial0/0
O 131.108.9.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1
[110/391] via 131.108.255.2, 00:00:42, Serial0/0
O IA 131.108.8.0/24 [110/400] via 131.108.255.6, 00:00:42, Serial0/1
[110/400] via 131.108.255.2, 00:00:42, Serial0/0
R1’s routing table has the remote OSPF networks labeled as O IA because the network
131.108.8.0/24 is part of an area not directly attached to R1. Also, R1 is automatically load
balancing across the two paths because the cost metric is the same (391). The administrative
distance is 110 (the default).
NOTE The election of the designated router in networks such as Frame Relay is important, and you
must ensure the hub or core network router is the elected DR so that the hub router disseminates
information to all spoke routers. To ensure the hub is the DR, you can disable the DR election
process on edge routers with the IOS command, ip ospf priority 0.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-98-320.jpg)
![76 Chapter 2: General Networking Topics
Border Gateway Protocol
Border Gateway Protocol (BGP) is an exterior routing protocol used widely in the Internet. It
is commonly referred to as BGP4 (version 4).
BGP4 is defined in RFC 1771. BGP allows you to create an IP network free of routing loops
between different autonomous systems.
An autonomous system (AS) is a set of routers under the same administrative control.
BGP is called a path vector protocol because it carries a sequence of AS numbers that indicates
the path taken to a remote network. This information is stored so that routing loops can be avoided.
BGP uses TCP as its Layer 4 protocol (TCP port 179). No other routing protocol in use today
relies on TCP. This allows BGP to make sure that updates are sent reliably, leaving the routing
protocol to concentrate on gathering information about remote networks and ensuring a loop-
free topology.
Routers configured for BGP are typically called BGP speakers, and any two BGP routers that
form a BGP TCP session are called BGP peers or BGP neighbors.
BGP peers initially exchange full BGP routing tables. After the exchange, only BGP updates
are sent between peers, ensuring that only useful data is sent unless a change occurs.
Four message are types used in BGP4 to ensure that peers are active and updates are sent:
• Open Messages—Used when establishing BGP peers.
• Keepalives—These messages are sent periodically to ensure connections are still active
or established.
• Update messages—Any changes that occur, such as a loss of network availability, result
in an update message.
• Notification—Only used to notify BGP peers of any receiving errors.
Key BGP characteristics include the following:
• BGP is a path vector protocol.
• BGP uses TCP as the transport layer protocol.
• Full routing table is exchanged only during initial BGP session.
• Updates are sent over TCP port 179.
• BGP sessions are maintained by keepalive messages.
• Any network changes result in update messages.
• BGP has its own BGP table. Any network entry must reside in the BGP table first.
• BGP has a complex array of metrics, such as next-hop address and origin, which are called
attributes.
• BGP supports VLSM and summarization (sometimes called Classless Interdomain
Routing [CIDR]).](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-99-320.jpg)
![84 Chapter 2: General Networking Topics
Table 2-16 displays some common multicast addresses and their uses.
Table 2-16 Class D Multicast Address Examples
Multicast Address Use
224.0.0.1 All hosts on subnets
224.0.0.2 All multicast routers
224.0.0.5 All OSPF-enabled routers
224.0.0.6 All OSPF DR routers
224.0.0.9 RIPv2-enabled routers
224.0.0.10 All EIGRP-enabled routers
TIP The Class D addresses used in multicast traffic range from 224.0.0.0 to 239.255.255.255.
Asynchronous Communications and Access Devices
An asynchronous (async) communication is a digital signal that is transmitted without precise
clocking. The RS-232 session between a router and PC through the console connection is an
example of async communications. Such signals generally have different frequencies and phase
relationships. Asynchronous transmissions usually encapsulate individual characters in control
bits (called start and stop bits) that designate the beginning and the end of each character.
For example, the auxiliary port on Cisco routers can be used to connect a modem and allow out
of band (not via the network) management.
The Cisco AS5300 is an example of a device that supports both synchronous and async com-
munication, such as voice, digital, and modem-based traffic (via a Public Switch Telephone
Network [PSTN]).
The AS5300, or universal Access Server (AS), is a versatile data communications platform that
provides the functions of an access server, router, and digital modem in a single modular
chassis. The access server is intended for ISPs, telecommunications carriers, and other service
providers that offer managed Internet connections. The AS5300 provides both digital (for
example, ISDN) and analog access (dialup users using PSTN) to users on a network.
Figure 2-20 displays a typical scenario where clients, such as Internet dialup users with ISDN
and analog phone lines (PSTN), can connect to the Internet using PPP.
Clients are supplied one number to call, and the AS5300 makes intelligent decisions based on
the incoming call type, whether it be digital (ISDN) or analog (PSTN).](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-107-320.jpg)
![86 Chapter 2: General Networking Topics
Example 2-21 SGBP Configuration Example
Hostname AS1
!
username CCIE password CCIE
sgbp group CCIE
sgbp member AS2 1.1.1.2
sgbp member AS3 1.1.1.3
sgbp member AS4 1.1.1.4
The following list explains the IOS commands used in Example 2-21.
• username CCIE password CCIE—Defines the username and password used for
authenticating SGBP members. If the password is wrong, an error such as the following
is presented on the console:
%SGBP-1-AUTHFAILED: Member [chars] failed authentication
• sgbp group CCIE—Defines a named stack group and makes this router a member of that
stack group. Use the sgbp group command in global configuration mode. To remove the
definition, use the no form of this command.
• sgbp member ip-address—Specifies the host name and IP address of a router or access
server that is a peer member of a stack group. Use the sgbp member command in global
configuration mode.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-109-320.jpg)
![110 Chapter 3: Application Protocols
Foundation Topics
Domain Name System
This section covers Domain Name System (DNS) and sample configurations used on Cisco IOS
routers.
DNS’s primary use is to manage Internet names across the World Wide Web. For users or clients
to use names instead of 32-bit IP addresses, the TCP/IP model designers developed DNS to
translate names into IP addresses.
DNS uses TCP and UDP port number 53.
In a large IP environment, network users need an easier way to connect to hosts without having
to remember 32-bit IP addresses—that’s where DNS comes into play. DNS provides a service
that allows users to use a host’s name in place of an IP Address to connect to hosts. When DNS
services are running, the host’s name is used to request its IP address from a DNS server. The
DNS server is a host running the DNS service, and it is configured to do the translation for the
user transparently. In other words, the user never sees the DNS request and host-to-IP address
translation. The client simply connects to a host name, and the DNS server does the translation.
For example, the website www.cisco.com is translated to the IP address 198.133.129.25.
DNS is a distributed database where organizations can use a predefined name or extension to
all their devices. Nations can use extensions to define hosts residing in their country. For
example, the extension for Australia is defined as .au. To reach the Cisco website in Australia,
a user would type www.cisco.com.au in a web browser.
A regulatory body called the Internet Registration Authority manages domain names.
Similar to DNS, Cisco routers can be configured to locally look up names so network
administrator can simply type a name rather than an IP address. Local names can also be
configured for devices.
To illustrate a local DNS lookup on a Cisco IOS router, look at the following Cisco router
command that provides a host lookup. (Note: a router will not provide DNS server responses to
client devices such as PCs or UNIX hosts.)
The following IOS command defines a local name to IP address:
ip host name [tcp-port-number] ip address1 [ip address2...ip address8]
You can assign more than one IP address to any given name.
Example 3-1 displays three hosts and their corresponding IP addresses.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-133-320.jpg)
![112 Chapter 3: Application Protocols
NOTE By default, Cisco routers search for a DNS server. To disable this feature, use the IOS command
no ip domain-lookup. This stops the router from querying a DNS server whenever a name
translation is required. This command is a definite time saver for the CCIE Security Lab exam.
To enable a Cisco IOS router to perform DNS lookup to a remote DNS server, the following
steps are required:
Step 1 For local DNS entries, you must specify any local host mapping with the
following IOS command (note that the tcp-port-number is used for
connections on a different TCP port number other than the default, 23):
ip host name [tcp-port-number] ip address1 [ip address2...ip address8]
Step 2 Specify the domain name or a domain list (Cisco routers can be configured
with multiple domain names) with the following IOS commands:
— ip domain-name name defines a default domain name that the Cisco
IOS Software uses to complete unqualified host names.
— ip domain-list name defines a list of default domain names to complete
unqualified host names.
Step 3 Specify the DNS server or servers with the following IOS command:
ip name-server server-address1 [server-address2...server-address6]
Devices such as PCs can also be configured for DNS servers and domain names. Example 3-4
configures a router named R1 with the domain name cisco.com. The domain name servers are
131.108.255.1 and 131.108.255.2.
Example 3-4 DNS Configuration
R1(config)#ip domain-name cisco.com
R1(config)#ip name-server 131.108.255.1
R1(config)#ip name-server 131.108.255.2
When a network administrator types a name (not a valid IOS command, of course), the Cisco
router attempts to translate the name into an IP address, first from the DNS server with the IP
address 131.108.255.1, and then from the DNS server 131.108.255.2.
Example 3-5 displays a successful DNS query and translation to the host named ccie (another
Cisco router) from the DNS server 131.108.255.1.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-135-320.jpg)
![114 Chapter 3: Application Protocols
Figure 3-1 displays the available options when configuring the TFTP application software.
Figure 3-1 Cisco TFTP Application Software Options
Includes logging of all
TFTP transfers
Defines from where files
are to be downloaded
The TFTP directory in Figure 3-1 is defined as c:tftpboot. On the host TFTP server (in this
case a Windows 2000 PC), the IOS images reside in the tftpboot directory at c:tftpboot. This
download directory option is a configurable option, and you can select any valid directory on
the host TFTP server.
The file is located in the tftpboot directory. In this example, the IOS image is named
c2600-js-mz.121-5.T10.bin.
To copy an IOS image from a TFTP server, the IOS command is copy tftp flash. Example 3-6
displays a TFTP request for the file c2600-js-mz.121-5.T10.bin from a TFTP server with an IP
address of 150.100.1.253.
Example 3-6 TFTP File Transfer
R1#copy tftp flash
Address or name of remote host []? 150.100.1.253
Source filename []? c2600-js-mz.121-5.T10.bin
Destination filename [c2600-js-mz.121-5.T10.bin]? c2600-js-mz.121-5.T10.bin
Erase flash: before copying? [confirm]Y
Erasing the flash filesystem will remove all files! Continue? [confirm]Y
Erasing device... eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee
eeeeee ...erased
Erase of flash: complete
Loading c2600-js-mz.121-5.T10.bin from 150.100.1.253 (via Ethernet0/0):
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-137-320.jpg)
![File Transfer Protocol 115
Example 3-6 TFTP File Transfer (Continued)
[OK - 11432808/22864896 bytes]
Verifying checksum... OK (0xBC59)
11432808 bytes copied in 106.126 secs (107856 bytes/sec)
R1#
The file (c2600-js-mz.121-5.T10.bin) is successfully copied and placed on the flash system on
Router R1. The only two mechanisms for security permitted with TFTP are the filename and
directory. TFTP has no mechanism for checking username and password. On a UNIX server
where the TFTP server daemon is installed, the file to be copied must have the appropriate
access rights. In UNIX, the Touch command is used to allow a TFTP request. For a Windows-
based platform, the software must be configured to permit file creation on the Windows-based
file system.
FTP, on the other hand, is a connection-based protocol, where username and password combi-
nations are used to authorize file transfers.
File Transfer Protocol
File Transfer Protocol (FTP), an application layer protocol of the TCP/IP protocol suite of
applications, allows users to transfer files from one host to another. Two ports are required for
FTP—one port is used to open the connection (port 21), and the other port is used to transfer
data (20). FTP runs over TCP and is a connection-oriented protocol. To provide security, FTP
allows usernames and passwords to be exchanged before any data can be transferred, adding
some form of security authentication mechanism to ensure that only valid users access FTP
servers.
The advantages of FTP are the ability to list a remote FTP server’s full list of directories and
ensure that only valid users are connected. The file transfer progress can be displayed to the FTP
client, as well. Many FTP applications are available, and the range of options is endless. For
example, on the CCIE Security lab exam, the application Reflection 2000 can be used for Telnet
and FTP. For more details on this application, visit www.wrq.com/products/reflection/.
NOTE FTP connection issues are typically communicated by end users (FTP clients) as poor network
performance when the problem might actually be a result of filtering the FTP data on port 20.
For example, when a client successfully logs into an FTP server remotely but fails to list the
remote FTP server’s directory or to transfer files, this can indicate a problem with the FTP data
port (via TCP port 20) or an access list problem on the remote network.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-138-320.jpg)
![120 Chapter 3: Application Protocols
Figure 3-5 HTTP Web Page on a Cisco Router
HTTP options; simply
click to expand IOS
command set.
Help Options
NOTE The command to disable HTTP server on a Cisco router is no ip http server. To set
username/password pairs, use the following IOS command:
username username privilege [0-15] password password
You can also define the HTTP port number with the following command:
ip http [0-65535]
The default is 80.
Secure Socket Layer
Secure Socket Layer (SSL) is an encryption technology for web host devices used to provide
secure transactions. For example, a secure transaction is required when clients enter their credit
card numbers for e-commerce via their browser. When the end user enters a web address via an
Internet browser, such as Internet Explorer, instead of entering HTTP: //web address in the
address window, the end user enters HTTPS://web address.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-143-320.jpg)
![Simple Network Management Protocol 121
Secure Hypertext Transfer Protocol secure site, or HTTPS, transports HTTP-based traffic over
an SSL connection and provides a stronger authentication mechanism than HTTP.
HTTPS runs over TCP port 443. SSL is defined in RFC 2246.
The SSL Handshake Protocol was first developed by Netscape Communications Corporation to
provide security and privacy over the World Wide Web. The SSL protocol supports server and
client authentication. The SSL protocol is application-independent, allowing protocols like
HTTP, FTP, and Telnet to be layered on top of it transparently. In other words, it is a session
layer-based protocol. Cisco has developed a number of content-based switches to accelerate
this communication, such as the Cisco SCA 11000 Series Secure Content Accelerator. The
Cisco SCA 11000 Series Secure Content Accelerator is an appliance-based solution that
increases the number of secure connections supported by a website by offloading the processor-
intensive tasks related to securing traffic with SSL. After an SSL session is established, no
further authentication is required. Chapter 5, “Security Protocols,” broadens this discussion
on public security by discussing topics such as private and public keys, and how keys are
exchanged through the Certificate Authority (CA) to ensure that SSL is secure.
Simple Network Management Protocol
Application layer protocol, Simple Network Management Protocol (SNMP), is used to manage
IP devices. SNMP is part of the TCP/IP application layer suite. SNMP allows network admin-
istrators the ability to view and change network parameters and monitor connections locally and
remotely. Managing network performance over a period of time is one of the major functions
that SNMP provides.
There are three version of SNMP:
• SNMP Version 1 (SNMPv1)
• SNMP Version 2 (SNMPv2)
• SNMP Version 3 (SNMPv3)
Both SNMPv1 and SNMPv2 use a community-based form of security. The community string
allows access to the SNMP agent and can also be defined by an IP address access control list
and password.
To set up the community access strings to permit access to the Simple Network Management
Protocol (SNMP) on a Cisco IOS router, use the snmp-server community global configuration
command:
snmp-server community string [view view-name] [ro | rw] [number]](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-144-320.jpg)
![124 Chapter 3: Application Protocols
Management Information Base (MIB), a database of network management information, is used
and maintained by a management protocol such as SNMP. The value of an MIB object can be
changed or retrieved using SNMP commands, usually through a GUI network management
system. Cisco supports a number of defined and proprietary MIB commands.
If the snmp-server community command is not used during the SNMP configuration session,
it will automatically be added to the configuration after the snmp-server host command is
used. In this case, the default password (string) for the snmp-server community is taken from
the snmp-server host command. You must always set the community string manually;
otherwise, your router could be left vulnerable to SNMP get commands.
Example 3-7 configures a Cisco IOS router for SNMP support.
Example 3-7 Sample SNMP Configuration
snmp-server community public RO
snmp-server enable traps config
snmp-server host 131.108.255.254 isdn
The IOS command snmp-server community public RO enables SNMP on a Cisco router. This
command is also used to restrict access via SNMP. The community string is defined as public
and acts as a password protection mechanism against unauthorized users. The community string
is sent in every SNMP packet, so an incorrect community string results in no authorized access
to the SNMP agent. The read-only attribute means that no configuration changes will be
permitted via an SNMP.
The IOS command snmp-server enable traps config advises the NMS of any configura-
tion changes. The IOS command snmp-server host 131.108.255.254 isdn alerts the host
131.108.254.254 of any ISDN traps. ISDN traps can include link flapping or high link usage,
for example. (See Table 3-2 for a comprehensive list of traps.)
To specify the recipient of an SNMP notification operation, use the snmp-server host global
configuration command. To remove the specified host, use the no form of this command.
snmp-server host host-addr [traps | informs] [version {1 | 2c | 3
[auth | noauth | priv]}] community-string
[udp-port port] [notification-type]
Table 3-3 expands the snmp-server host IOS command and presents the full range of options,
including MD5 authentication.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-147-320.jpg)
![Simple Network Management Protocol 125
Table 3-3 snmp-server host Command
Syntax Description Meaning
host-addr Name or Internet address of the host (the targeted recipient).
traps (Optional) Sends trap messages to this host. This is the default.
informs (Optional) Sends Inform messages to this host.
version (Optional) Version of the SNMP used to send the traps. Version 3 is the most
secure model because it allows packet encryption with the priv keyword. If
you use the version keyword, one of the following must be specified:
1—SNMPv1. This option is not available with informs.
2c—SNMPv2C.
3—SNMPv3.
The following three optional keywords can follow the 3 keyword:
auth—(Optional) Enables Message Digest 5 (MD5) and Secure Hash
Algorithm (SHA) packet authentication.
noauth—(Default) The noAuthNoPriv security level. This is the default if the
[auth | noauth | priv] keyword choice is not specified.
priv—(Optional) Enables Data Encryption Standard (DES) packet
encryption (also called privacy).
community-string Password-like community string sent with the notification operation.
Although you can set this string using the snmp-server host command by
itself, it is recommended that you define this string using the snmp-server
community command prior to using the snmp-server host command.
udp-port port (Optional) UDP port of the host to use. The default is 162.
notification-type (Optional) Type of notification to be sent to the host. If no type is specified,
all notifications are sent. The notification type can be one or more of the
following keywords:
bgp—Sends Border Gateway Protocol (BGP) state change notifications.
calltracker—Sends Call Tracker call-start/call-end notifications.
config—Sends configuration notifications.
dspu—Sends downstream physical unit (DSPU) notifications.
entity—Sends Entity MIB modification notifications.
envmon—Sends Cisco enterprise-specific environmental monitor
notifications when an environmental threshold is exceeded.
frame-relay—Sends Frame Relay notifications.
hsrp—Sends Hot Standby Routing Protocol (HSRP) notifications.
continues](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-148-320.jpg)
![Network Time Protocol 129
Figure 3-7 displays a simple two-router network where Router R1 will be configured to supply
a clock source to the Router R2. In this example, you will configure authentication and ensure
that the NTP peer between the two routers is secure.
Figure 3-7 NTP Sample Configuration
My clock is set to
August 9, 2002,
time 10:47:48 a.m.
131.108.3.0/30
Ethernet0/0 Frame Relay Ethernet0/0
NTP NTP
172.108.1.1/24 Server Client 172.108.2.1/24
Send Receive
R1 NTP NTP R2
Serial0/0.1 Serial0/0.2
I have NTP atomic
clock source; my stratum
value is 2.
The following steps are required when enabling NTP on a Cisco router:
1 Define the time zone with the following command:
clock timezone zone hours [minutes]
2 Configure the master NTP router (this router will supply a clock to other routers) with the
following command:
ntp master [stratum value]
The stratum value is 1 to 15, with 1 representing the best clock source.
3 To configure a remote NTP peer to a Cisco router with a better stratum value, use the
following IOS command:
ntp peer ip-address [version number] [key keyid] [source interface] [prefer]
Table 3-4 displays the required parameters for the ntp peer command.
4 To define NTP to authenticate the NTP session, use the following IOS commands:
ntp trusted-key key-number
The key-number is the authentication key to be trusted.
ntp authentication-key number md5 value](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-152-320.jpg)
![134 Chapter 3: Application Protocols
Foundation Summary
The “Foundation Summary” is a condensed collection of material for a convenient review of
this chapter’s key concepts. If you are already comfortable with the topics in this chapter and
decided to skip most of the “Foundation Topics” material, the “Foundation Summary” will help
you recall a few details. If you just read the “Foundation Topics” section, this review should
help further solidify some key facts. If you are doing your final preparation before the exam,
the “Foundation Summary” offers a convenient and quick final review.
Table 3-5 DNS Concepts
Concept Description
Well-known port numbers UDP Port 53, TCP Port 53
ip host name [tcp-port-number] Configured locally to assign a host name with up to 8 IP
ip address1 [ip address2...ip address8] addresses
no ip domain-lookup Disables the IP DNS-based host name-to-address translation
ip domain-name name Defines a default domain name that the Cisco IOS Software
uses to complete unqualified host names
ip domain-list name Defines a list of default domain names to complete
unqualified host names
ip name-server ip address Specifies the address of one or more name servers to use for
name and address resolution; up to six name servers
permitted
Table 3-6 TFTP Concepts
Concept Description
Well-known port numbers UDP Port 69 (UDP is typically the only supported protocol for TFTP
produced by vendors) and TCP Port 69
copy tftp flash Cisco IOS command to copy images from a TFTP server
Security Only filename and directory name are methods used to secure transfers
Table 3-7 Secure Shell (SSH) Concepts
Concept Description
Well-known port number TCP port 443.
HTTPS HTTP traffic runs over a secure connection.
Service/client SSH uses a client server model where clients request secure connections
authentication to a host device, such as with a credit card transaction over the World
Wide Web.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-157-320.jpg)
![Foundation Summary 135
Table 3-8 SNMP Concepts
Concept Description
Well-known port numbers UDP 161 (SNMP servers) and UDP 162 (SNMP clients).
SNMP managed devices An SNMP managed device is a network node that contains an SNMP
agent and resides on a managed network. Managed devices collect and
store management information and make this information available to
Network Management System using SNMP.
SNMP agent SNMP Agent is a network management software module that resides in a
managed device. An agent has local knowledge of management
information and translates that information into a form compatible with
SNMP.
Table 3-9 SMTP Concepts
Concept Description
Well-known port numbers TCP 25 and UDP 25
HELO command Used in communications between host and client
Table 3-10 NTP Concepts
Concept Description
Well-known port numbers TCP 123 and UDP 123.
ntp master 1-15 Defines stratum value between 1 and 15.
clock set hh:mm:ss day month year Manually sets clock on a Cisco router.
ntp peer ip-address [version number] [key Defines NTP peers.
keyid] [source interface] [prefer]
ntp authenticate Enables authentication.
ntp authentication-key number md5 value Defines NTP authentication key and password.
ntp trusted-key key-number Defines NTP to authenticate NTP session; key-number
is the authentication key to be trusted.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-158-320.jpg)
![Scenario 3-1: Configuring DNS, TFTP, NTP, and SNMP 141
1 What happens when a network administrator types the host name Router1 at the router
prompt? (Select the best two answers.)
a. DNS queries are disabled; nothing will be translated.
b. The name Router1 is mapped to the IP address 131.108.1.1.
c. The administrator could also type CCIE to reach the same IP address (131.108.1.1).
d. Because DNS is disabled with the command no ip domain-lookup, the router
assumes this is an invalid IOS command and returns the error “% Unknown com-
mand or computer name, or unable to find computer address.”
e. Local DNSs are case-sensitive so you can only type Router1 to map to 131.108.1.1.
2 The following commands are entered on the router named R1. What are the TFTP server
address and TFTP filename stored on the router on board flash?
R1#copy tftp flash
Address or name of remote host []? 150.100.1.253
Source filename []? c2600-jo3s56i-mz.121-5.T10.bin
Destination filename [c2600-jo3s56i-mz.121-5.T10.bin]? c2600-c1
3 R1 supplies an NTP clock source to a remote router. What is the NTP’s peer IP address,
and what is the MD5 password used to ensure that NTP sessions are authenticated?
4 What is the SNMP read-write access community string for the following configuration?
snmp-server community public RO
snmp-server community publiC RW](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-164-320.jpg)
![142 Chapter 3: Application Protocols
Scenario Answers
Scenario 3-1 Solutions
1 Answers: b and c. The host name Router1 (not case-sensitive) is mapped to
131.108.1.1 with the command ip host Router1 131.108.1.1. Also, the IOS command
CCIE is mapped to the same name with the IOS command ip host CCIE 131.108.1.1.
If you look at the IP address assigned to the Ethernet 0/0, it’s the local IP address.
Therefore, if a user types Router1 or CCIE, they will be return to the same router.
The following sample display demonstrates this fact:
R1#router1
Translating "router1"
Trying Router1 (131.108.1.1)... Open
User Access Verification
Password:
R1>quit
! quit commands exit Telnet session and you return
! to the first Telnet connection on R1
[Connection to router1 closed by foreign host]
R1#ccie
Translating "ccie"
Trying CCIE (131.108.1.1)... Open
User Access Verification
Password:
R1>
Both the DNS names, CCIE and Router1, are translated to the same IP address,
131.108.1.1.
2 Answer: The TFTP server address is 150.100.1.253 and the filename requested is
c2600-jo3s56i-mz.121-5.T10.bin. However, the last command entered is the destina-
tion filename, which defines the names stored locally on the system flash. In this case,
the network administrator types the filename c2600-c1.
3 Answer: R1 is configured statically to peer to the remote NTP IP address, 131.108.2.1
(ntp peer 131.108.2.1 key 1). The MD5 password is configured but, unfortunately, the
configuration will not display the MD5 passwords (encrypted), so it cannot be
derived.
4 Answer: The read-only (RO) community string is named public, and the read-write
(RW) community string is set to publiC. Community strings are case-sensitive.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-165-320.jpg)
![152 Chapter 4: Cisco IOS Specifics and Security
NOTE On a high-performance router, such as Cisco 4500 series and 7500 series routers, you can make
the Flash system look like a file system and store many versions of IOS. The IOS command to
partition the System Flash is partition flash number-of-partition size-of-each-partition.
Example 4-1 show flash Command
R1>show flash
System flash directory:
File Length Name/status
1 9558976 c2500-ajs40-l.12-17.bin
[9559040 bytes used, 7218176 available, 16777216 total]
16384K bytes of processor board System flash
Example 4-1 shows that the IOS image, c2500-ajs40-l.12-17.bin, is currently stored on the
router’s on-board System Flash.
The Cisco 7500 series router provides the option of installing additional PCMCIA Flash
memory. If this additional memory is installed, the dir slot0: IOS command displays the IOS
image stored in slot0.
NOTE The IOS image’s name conveys a lot of information, including the platform and feature sets.
For more information, go to www.cisco.com and search for “software naming convention.”
Central Processing Unit
The central processing unit (CPU) is the heart of a router, and every Cisco router has a CPU. A
CPU manages all the router’s processes, such as IP routing, and new routing entries, such as
remote IP networks learned through a dynamic routing protocol.
To view a CPU’s status, use the show process IOS command.
Example 4-2 shows a sample display taken from a Cisco IOS router.
Example 4-2 (Truncated) show process Command
R1>show process
CPU utilization for five seconds: 9%/7%; one minute: 9%;
five minutes: 10%
PID QTy PC Runtime (ms) Invoked uSecs Stacks TTY Proc
1 Csp 318F396 24456 1043 234 732/1000 0 Load Meter
2 M* 0 28 28 1000 3268/4000 0 EXEC
3 Lst 317D1FC 1304 175 5257 1724/2000 0 Check heap
...](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-175-320.jpg)
![Cisco Hardware 153
The show process command displays the router utilization within the past five seconds, the past
one minute, as well as the average over the last five minutes. Details about specific processes
follow the CPU utilization statistics.
Read-Only Memory
Read-only memory (ROM) stores a scaled-down version of a router’s IOS in the event that the
Flash system becomes corrupted or no current IOS image is stored in Flash. ROM also contains
the bootstrap program (sometimes referred to as the rxboot image in Cisco documentation) and
a device’s power up diagnostics. You can perform only a software upgrade (that is, perform a
software image upgrade on the ROM) by replacing ROM chips because the ROM is not
programmable.
The bootstrap program enables you to isolate or rule out hardware issues. For example, you
might have a faulty Flash card and, subsequently, the router cannot boot the IOS image. The
power diagnostics program tests all the hardware interfaces on the router. ROM mode contains
a limited number of IOS commands, which enables the administrator or the Technical Assis-
tance Center (TAC) to help troubleshoot and ascertain any hardware or configuration issues on
a Cisco router. Cisco TAC is available 24 hours a day, seven days a week. You must pay Cisco
for this service and have a valid contract number to open any cases.
Unfortunately, not all Cisco routers have the same ROM code, so the commands might vary but
the principle remains the same. You can always issue the ? command in ROM mode to identify
the available commands used to troubleshoot a Cisco IOS-based router. Newer Cisco hardware
models now contain a new boot program stored in Boot Flash rather than in the ROM. The
program is a little more user-friendly. Menu-driven options are available to change the
configuration register, for example.
Example 4-3 provides all the available options on a Cisco 4000 router when the ? command is
used in ROM mode.
Example 4-3 ? Command When in ROM Mode
> ?
? Types this display
$ Toggle cache state
B [filename] [TFTP Server IP address | TFTP Server Name]
Load and excutute system image from ROM or from TFTP server
C [address] Continue [optional address]
D /S M L V Deposit value V of size S into location L with
modifier M
E /S M L Examine location L with size S with modifier M
G [address] Begin execution
H Help for commands
I Initialize
K Displays Stack trace
L [filename] [TFTP Server IP address | TFTP Server Name]
continues](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-176-320.jpg)
![Cisco Hardware 157
To view the current LAN or WAN interface, issue the show interface command. The show
interface command displays all LAN and WAN interfaces. To display information regarding
console or auxiliary ports, use the show line command. Figure 4-2 summarizes the available
IOS commands that administrators can use to view a router’s current configuration.
Figure 4-2 Interface IOS Commands
show flash show startup-config
dir slot0. show config
show running-config
write terminal
Random-Access Memory (RAM)
Flash Read-Only Nonvolatile RAM
Memory (ROM) (NVRAM)
LAN, WAN,
Router Interfaces
Console, AUX Port
show interfaces
Now that you have reviewed Cisco routers’ hardware basics, it’s time to review how routers
operate. In addition to router operation, this chapter covers how administrators can manage
Cisco routers by saving and loading files to and from a TFTP server.
NOTE Cisco routers can operate in a number of modes. Cisco defines them as follows:
• ROM boot mode—When the router is in boot mode and loaded with a subset of the IOS
image, only a limited number of commands are available.
• Configuration mode—Where you can make configuration changes. An example prompt
is Router1(config)#.
• Interface configuration mode—Where you make configuration changes to interfaces
such as the Ethernet or Serial connections. Example prompt is Router1(config-if)#.
• Initial configuration mode—When a router first boots up out of the box with no initial
configuration, you are prompted for basic system configuration details, such as name and
IP address assignment. The prompt looks like this:
Would you like to answer the initial configuration dialog? [yes/no]](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-180-320.jpg)
![158 Chapter 4: Cisco IOS Specifics and Security
• User EXEC mode—Basic IOS commands are permitted from the command-line
interface (CLI). An example prompt is R1>.
• Privileged EXEC mode (also referred to as enabled mode)—Advance IOS commands
are permitted when the enable password or secret password is entered from the CLI. An
example prompt is R1#.
Saving and Loading Files
The configuration file can reside on the router’s NVRAM, RAM, or on a TFTP server. When a
router boots with the default configuration register (0x2102), the configuration file is copied
from NVRAM to RAM.
Network administrators typically save the configuration files to a TFTP server as a backup, in
case of a router failure.
To save a configuration file from RAM to NVRAM (after configuration changes are made), the
IOS command is copy running-config startup-config. The write terminal command will also
copy the running configuration to startup configuration. The write command is a legacy com-
mand from earlier releases of IOS still valid in today’s versions of IOS software.
Example 4-5 displays a successful configuration change on Ethernet 0/0, followed by a network
administrator in PRIV EXEC (privilege EXEC mode) mode saving the new configuration file
to NVRAM.
Example 4-5 Saving IOS Configurations Files
R1#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#interface ethernet 0/0
R1(config-if)#ip address 131.108.1.1 255.255.255.0
R1(config-if)#exit
R1#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
R1#
Table 4-3 summarizes the configuration file manipulation that can be performed on Cisco IOS
routers.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-181-320.jpg)
![160 Chapter 4: Cisco IOS Specifics and Security
Example 4-6 displays a list of truncated show commands available from the CLI on a Cisco
router in PRIV EXEC mode.
Example 4-6 show Commands
R1#show ?
access-expression List access expression
access-lists List access lists
accounting Accounting data for active sessions
adjacency Adjacent nodes
aliases Display alias commands
arp ARP table
async Information on terminal lines used as router
interfaces
backup Backup status
bgp BGP information
bridge Bridge Forwarding/Filtering Database [verbose]
buffers Buffer pool statistics
caller Display information about dialup connections
cef Cisco Express Forwarding
class-map Show QoS Class Map
clock Display the system clock
configuration Contents of Non-Volatile memory
connection Show Connection
context Show context information
controllers Interface controller status
cops COPS information
crypto Encryption module
debugging State of each debugging option
derived-config Derived operating configuration
dhcp Dynamic Host Configuration Protocol status
diag Show diagnostic information for port
adapters/modules
dial-peer Dial Plan Mapping Table for, e.g. VoIP Peers
dialer Dialer parameters and statistics
dialplan Voice telephony dial plan
diffserv Differentiated services
dlsw Data Link Switching information
dnsix Shows Dnsix/DMDP information
docsis Show DOCSIS
drip DRiP DB
dspu Display DSPU information
dxi atm-dxi information
entry Queued terminal entries
environment Environmental monitor statistics
exception exception informations
file Show filesystem information
flash: display information about flash: file system
frame-relay Frame-Relay information
fras FRAS Information
fras-host FRAS Host Information
gateway Show status of gateway
history Display the session command history](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-183-320.jpg)
![162 Chapter 4: Cisco IOS Specifics and Security
Example 4-6 show Commands (Continued)
users Display information about terminal lines
version System hardware and software status
vlans Virtual LANs Information
vtemplate Virtual Template interface information
whoami Info on current tty line
This section briefly covers the highlighted commands in Example 4-6.
Example 4-7 displays sample output from the most widely used IOS command, show ip route.
Example 4-7 show ip route Command
R1#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
131.108.0.0/16 is variably subnetted, 3 subnets, 2 masks
C 131.108.255.0/30 is directly connected, Serial0/0
O 131.108.2.0/24 [110/400] via 131.108.255.2, 00:00:03, Serial0/0
C 131.108.1.0/24 is directly connected, Ethernet0/0
R1#show ip route ?
Hostname or A.B.C.D Network to display information about or hostname
bgp Border Gateway Protocol (BGP)
connected Connected
egp Exterior Gateway Protocol (EGP)
eigrp Enhanced Interior Gateway Routing Protocol (EIGRP)
igrp Interior Gateway Routing Protocol (IGRP)
isis ISO IS-IS
list IP Access list
mobile Mobile routes
odr On Demand stub Routes
ospf Open Shortest Path First (OSPF)
profile IP routing table profile
rip Routing Information Protocol (RIP)
static Static routes
summary Summary of all routes
supernets-only Show supernet entries only
vrf Display routes from a VPN Routing/Forwarding instance
| Output modifiers
<cr>
R1#show ip route ospf
131.108.0.0/16 is variably subnetted, 3 subnets, 2 masks
O 131.108.2.0/24 [110/400] via 131.108.255.2, 00:00:30, Serial0/0
R1#](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-185-320.jpg)
![176 Chapter 4: Cisco IOS Specifics and Security
NOTE These are the generic steps for password recovery on a Cisco router. Some commands and
steps might be slightly different depending on the hardware platform. Refer to the Password
Recovery Procedures Index (www.cisco.com/warp/public/474/) for more information on each
platform.
To review, look at an example. Assume you are directly connected to Router R1 and you do not
know the enable password. You power cycle the router and press the Control Break key (the Esc
key) to enter boot mode.
Example 4-18 shows the dialog displayed by the router after a break is issued.
Example 4-18 Password Recovery Dialog on a Cisco Router
System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
Copyright (c) 1986-1995 by cisco Systems
Abort at 0x10EA882 (PC)
!control break issued followed by ? to view help options
>>?
------------>control break issued followed by ? to view help options
$ Toggle cache state
B [filename] [TFTP Server IP address | TFTP Server Name]
Load and EXECute system image from ROM
or from TFTP server
C [address] Continue EXECution [optional address]
D /S M L V Deposit value V of size S into location L with
modifier M
E /S M L Examine location L with size S with modifier M
G [address] Begin EXECution
H Help for commands
I Initialize
K Stack trace
L [filename] [TFTP Server IP address | TFTP Server Name]
Load system image from ROM or from TFTP server,
but do not begin EXECution
O Show configuration register option settings
P Set the break point
S Single step next instruction
T function Test device (? for help)
As you can see in Example 4-18, the ? symbol can display all the available options. To view the
current configuration register, issue the e/s 2000002 command, which displays the value of the
configuration register. Example 4-19 displays the current configuration register.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-199-320.jpg)
![178 Chapter 4: Cisco IOS Specifics and Security
Example 4-21 Dialog After Reload (Continued)
--- System Configuration Dialog ---
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Would you like to enter the initial configuration dialog? [yes]:No
Press RETURN to get started!
......
Router>ena !(no password required or entered)
Router#
Notice that the router reverts to the default configuration. Enter the enable command to enter
privilege EXEC mode. In this example, you will not be prompted for the enable password
because there isn’t one; by default, no enable password is configured when a Cisco IOS router
boots from the default configuration (no passwords are configured in this default state).
You can view the startup config by using the show startup-config command (or show config
in IOS versions predating version 10.3), as shown in Example 4-22.
Example 4-22 show startup-config Command
Router#show startup-config
Using 1968 out of 32762 bytes
! Last configuration change at 16:35:50 UTC Tue May 18 2002
! NVRAM config last updated at 16:35:51 UTC Tue May 18 2002
version 2.2
service password-encryption
hostname R1
! Note there is no secret password either
enable password 7 05080F1C2243
...
As you can see in Example 4-22, the enable password is encrypted. In instances where the
password is not encrypted, you could view the password using the show startup-config
command. When a password is encrypted, you must copy the startup configuration to the
running configuration and change the password manually by using the following IOS
command:
copy startup-config running-config
At this point, you are still in privileged mode, so you can now enter global configuration mode
to change the password back to its original setting (cisco, in this instance).
Example 4-23 displays the password change in global configuration mode set to the new
password of cisco.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-201-320.jpg)
![Basic Security on Cisco Routers 179
Example 4-23 Changing a Password and Setting the Configuration Registry Commands
hostname#copy startup-config running-config
Destination filename [running-config]?
2818 bytes copied in 1.475 secs (2818 bytes/sec)
R1#config terminal
R1(config)#enable password cisco
R1(config)#config-register 0x2102
R1(config)#exit
R1#reload
You complete password recovery by changing the configuration register back to the default
value (0x2102).
NOTE If a secret password is also configured, you must use the enable secret password IOS command
because the secret password overrides the enable password. Example 4-23 includes no secret
password, so you can use the enable password command.
When the Cisco IOS router reloads, it will load the new configuration file with the password set
to cisco.
Basic Security on Cisco Routers
You can access a Cisco router in a number of ways. You can physically access a router through
the console port, or you can access a router remotely through a modem via the auxiliary port.
You can also access a router through a network or virtual terminal ports (VTY lines), which
allow remote Telnet access.
If you do not have physical access to a router—either through a console port or an auxiliary port
via dialup—you can access a router through the software interface, called the virtual terminal
(also referred to as a VTY port). When you telnet to a router, you might be required to enter the
VTY password set by the network administrator. For example, on Router R1, the administrator
types R2’s remote address and tries to telnet to one of the VTY lines.
Example 4-24 provides the session dialog when a user telnets to the router with the IP address
131.108.1.2.
Example 4-24 Using a VTY Port to Establish a Telnet Connection
R1#Telnet 131.108.1.2
Trying 131.108.1.2 ... Open
User Access Verification
Password: xxxxx
R2>](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-202-320.jpg)
![184 Chapter 4: Cisco IOS Specifics and Security
Standard IP access lists filter on the source address only. The Cisco IOS syntax is as follows:
access-list access-list-number {deny | permit} [source-address]
[source-wildcard]
Table 4-6 describes the purpose of each field.
Table 4-6 Standard IP access-list Command Syntax Description
Command Field Description
access-list-number A number from 1 through 99 that defines a standard access list number.
Versions of IOS 12.0 or later also have standard access lists ranging
from 1300-1999.
deny IP packet is denied if a match is found.
permit IP packet is permitted if it matches the criteria, as defined by the
administrator.
source-address Source IP address or network. Any source address can be applied by
using the keyword any.
source-wildcard (optional) Wildcard mask that is to be applied to the source address. This is an
inverse mask, which is further explained with a few examples later in
this section. The default is 0.0.0.0, which specifies an exact match.
After creating the access list as described in Table 4-6, you must apply the access list to the
required interface using the following command:
ip access-group {access-list-number | name} {in | out}
Table 4-7 describes the purpose of each field.
Table 4-7 ip access-group Command Syntax Description
Command Field Description
access-list-number A number in the range from 1 through 99 and 1300 through 1999 that defines a
standard access list number.
name If you are using named access lists, that name will be referenced here.
in Keyword that designates the access list as an inbound packet filter.
out Keyword that designates the access list as an outbound packet filter. This is the
default action.
The wildcard mask previously mentioned in the access-list command matches the source
address. When the wildcard mask is set to binary 0, the corresponding bit field must match; if
it is set to binary 1, the router does not care to match any bit or it is an insignificant bit. For
example, the mask 0.0.255.255 means that the first two octets must match, but the last two
octets do not need to match—hence, the commonly used phrases care bits (0s) and don’t care
bits (1s).](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-207-320.jpg)
![188 Chapter 4: Cisco IOS Specifics and Security
For Internet Control Message Protocol (ICMP), use the syntax shown in Example 4-35.
Example 4-35 Access List Syntax for ICMP Traffic
access-list access-list-number [dynamic dynamic-name
[timeout minutes]] {deny | permit} icmp source source-wildcard
destination destination-wildcard [icmp-type [icmp-code]
[icmp-message] [precedence precedence] [tos tos] [log]
For Internet Group Management Protocol (IGMP), use the syntax shown in Example 4-36.
Example 4-36 Access List Syntax for IGMP Traffic
access-list access-list-number [dynamic dynamic-name
[timeout minutes]] {deny | permit} igmp source source-wildcard
destination destination-wildcard [igmp-type]
[precedence precedence] [tos tos] [log]
For TCP, use the syntax shown in Example 4-37.
Example 4-37 Access List Syntax for TCP Traffic
access-list access-list-number [dynamic dynamic-name
[timeout minutes]] {deny | permit} tcp source source-wildcard
[operator port [port]] destination destination-wildcard
[operator port [port]] [established] [precedence precedence]
[tos tos] [log]
For User Datagram Protocol (UDP), use the syntax shown in Example 4-38.
Example 4-38 Access List Syntax for UDP Traffic
access-list access-list-number [dynamic dynamic-name
[timeout minutes]] {deny | permit} udp source source-wildcard
[operator port [port]] destination destination-wildcard
[operator port [port]] [precedence precedence] [tos tos] [log]
As you can see, extended access lists have a range of options to suit any requirement. The most
often used extended access list options are as follows:
• access-list-number—Provides a number ranging from 100 through 199 that defines an
extended access list. Also numbers ranging from 2000 through 2699.
• deny—Denies access if the conditions are matched.
• permit—Permits access if the conditions are matched.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-211-320.jpg)
![Q&A 193
Q&A
The Q & A questions are designed to help you assess your readiness for the topics covered on
the CCIE Security written exam and those topics presented in this chapter. This format helps
you assess your retention of the material. A strong understanding of the answers to these ques-
tions will help you on the CCIE Security written exam. You can also look over the questions at
the beginning of the chapter again for additional review. Use the CD-ROM provided with this
book to take simulated exams, which draw from a database of over 300 multiple-choice ques-
tions—all different from those presented in the book.
Select the best answer. Answers to these questions can be found in Appendix A, “Answers to
Quiz Questions.”
1 Where is the running configuration stored on a Cisco router?
2 What IOS command displays the startup configuration?
3 What IOS command provides the following output?
System flash directory:
File Length Name/status
1 9558976 c2500-ajs40-l.12-17.bin
[9559040 bytes used, 7218176 available, 16777216 total]
16384K bytes of processor board System flash
4 What configuration register will enable a Cisco router to ignore the startup configuration?](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-216-320.jpg)
![214 Chapter 5: Security Protocols
Transactions between the client (end user) and the RADIUS server are authenticated through a
shared secret. The username is sent as clear text. RADIUS supports both Password Authentica-
tion Protocol (PAP) and Challenge Handshake Authentication Protocol (CHAP). PAP and
CHAP are security protocols that allow users to gain access to remote devices with PPP. A
RADIUS server will never send the user’s password over the network in any circumstance.
If the username/password pairing is entered incorrectly, the RADIUS server will send an
ACCESS_REJECT response. The end user must re-enter the pairings or the connection will
be rejected.
RADIUS supports a number of predefined attributes that can be exchanged between client
and server, such as the client’s IP address. RADIUS attributes carry specific details about
authentication.
RFC 2138 defines a number of attributes. The following bulleted list provides details from the
most common attributes:
• Attribute type 1—Username (defines usernames, such as numeric, simple ASCII
characters, or a Simple Mail Transfer Protocol [SMTP] address)
• Attribute type 2—User Password (defines the password, which is encrypted using
Message Digest 5 [MD5])
• Attribute type 3—CHAP Password (used only in access-request packets)
• Attribute type 4—NAS IP address (defines the NAS’s IP address; used only in access-
request packets)
• Attribute type 5—NAS Port (this is not the User Datagram Protocol (UDP) port number;
it indicates the NAS’s physical port number, ranging from 0 to 65,535)
• Attribute type 6—Service-Type (Type of service requested or type of service to be
provided). Not supported by Cisco IOS.
• Attribute type 7—Protocol (defines required framing; for example, PPP is defined when
this attribute is set to 1 and Serial Line Internet Protocol [SLIP] is set to 2)
• Attribute type 8—IP address (defines the IP address to be used by the remote user)
• Attribute type 9—IP subnet mask (defines the subnet mask to be used by the remote user)
• Attribute type 10—Routing
• Attribute type 13—Compression
• Attribute type 19—Callback ID
• Attribute type 26—Vendor-specific. Cisco (vendor-ID 9) uses one defined option: vendor
type 1 named cisco-avpair; this attribute transmits TACACS+ A/V pairs
• Attribute type 61—NAS port type
Table 5-2 summarizes RADIUS protocol’s main features](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-237-320.jpg)
![220 Chapter 5: Security Protocols
TACACS+ accounting provides an audit record of what commands were completed. The NAS
sends a record of any commands, and the TACACS+ server sends a response acknowledging
the accounting record.
Table 5-3 summarizes the main features of TACACS+.
Table 5-3 Summary of TACACS+ Protocol
Feature Feature
TCP Packets sent between client and server are TCP. Typically, the user can wait
for a username/password prompt.
TCP destination port Port 49.
Attributes Packet types are defined in TACACS+ frame format as follows:
Authentication 0x01
Authorization 0x02
Accounting 0x03
Seq_no The sequence number of the current packet flow for the current session. The
Seq_no starts with 1, and each subsequent packet will increment by one. The
client sends only odd numbers. TACACS+ server sends only even numbers.
Encryption method Entire packet is encrypted. Data is encrypted using MD5 and a secret key
that matches both on the NAS (for example, a Cisco IOS router) and the
TACACS+ server.
Multiprotocol support Support protocols, such as AppleTalk, NetBIOS, or IPX, along with IP.
Now, examine the TACACS+ configuration tasks required when enabling TACACS+ on a Cisco
IOS router.
TACACS+ Configuration Task List
To configure your router to support TACACS+, you must perform the following tasks:
Step 1 Use the aaa new-model global configuration command to enable AAA, which
must be configured if you plan to use TACACS+. For more information about
using the aaa new-model command, refer to the link, www.cisco.com/univercd/
cc/td/doc/product/software/ios121/121cgcr/secur_c/scprt1/index.htm.
Step 2 Use the tacacs-server host command to specify the IP address of one or
more TACACS+ daemons. The command is as follows:
tacacs-server host hostname [single-connection] [port integer] [timeout
integer] [key string]](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-243-320.jpg)
![228 Chapter 5: Security Protocols
Table 5-6 Kerberos Terminology (Continued)
Term Definition
Kerberos server A daemon running on a network host. Users and network services register
their identities with the Kerberos server. Network services query the
Kerberos server to authenticate to other network services. Also known as
the Master Kerberos server.
Key Distribution Center A Kerberos server and database program running on a network host.
(KDC)
Principal Also known as a Kerberos identity, this is who you are or what a service is
according to the Kerberos server.
Service credential A credential for a network service. When issued from the KDC, this
credential is encrypted with the password shared by the network service and
the KDC, and with the user’s TGT.
SRVTAB A password that a network service shares with the KDC. The network
service authenticates an encrypted service credential using the SRVTAB
(also known as a KEYTAB) to decrypt it.
Ticket Granting Ticket A credential that the KDC issues to authenticated users. When users receive
(TGT) a TGT, they can authenticate to network services within the Kerberos realm
represented by the KDC.
Kerberos Configuration Task List
To configure Kerberos support on a Cisco router, complete the following tasks:
Step 1 Define the default realm for the router:
kerberos local-realm kerberos-realm
Step 2 Specify to the router which KDC to use in a given Kerberos realm and,
optionally, the port number that the KDC is monitoring. (The default port
number is 88.)
kerberos server kerberos-realm {hostname | ip-address} [port-number]
Step 3 Map a host name or DNS domain to a Kerberos realm (optional):
kerberos realm {dns-domain | host} kerberos-realm
NOTE The kerberos local-realm, kerberos realm, and kerberos server commands are equivalent to
the UNIX krb.conf file.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-251-320.jpg)
![Virtual Private Dial-Up Networks (VPDN) 229
Example 5-12 displays a sample Kerberos configuration.
Example 5-12 Kerberos Configuration
kerberos local-realm CISCO.COM
kerberos server CISCO.COM 3.3.3.3
kerberos realm.cisco.com CISCO.COM
RADIUS and TACACS+ are far more common than Kerberos in today’s networks. Microsoft
2000, for example, uses Kerberos for internal authentication in Active Directory.
NOTE For a complete guide to Kerberos, a defined and open standard, please visit the following:
http://web.mit.edu/is/help/kerberos/
For UNIX experts, some of the most common UNIX executable commands when configuring
and enabling Kerberos are as follows:
• Kdb5_util—Allows the UNIX administrator to create the Kerberos database
• Kadmin—Allows the administrator to administer the Kerberos database
• Krb5kdc/kadmin—Starts the KDC daemon on the server
Cisco routers support encryption and Kerberos is used.
Another way for users to open a secure Telnet session is to use Encrypted Kerberized Telnet,
which authenticates users by their Kerberos credentials before a Telnet session is established.
The IOS command is connect host [port] /encrypt Kerberos and the exec prompt.
Virtual Private Dial-Up Networks (VPDN)
A VPDN is a network that extends remote access dialup clients to a private network. VPDN
tunnels use either Layer 2 forwarding (L2F) or Layer 2 Tunnel Protocol (L2TP).
Cisco introduced L2F in RFC 2341. It is also used to forward PPP sessions for Multichassis
Multilink PPP.
L2TP, introduced in RFC 2661, combines the best of the Cisco L2F protocol and Microsoft
Point-to-Point Tunneling Protocol (PPTP). Moreover, L2F supports only dial-in VPDN, while
L2TP supports both dial-in and dial-out VPDN.
Both protocols use UDP port 1701 to build a tunnel through an IP network to forward link-layer
frames.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-252-320.jpg)
![Internet Key Exchange (IKE) 253
authentication method, rsa-encr, which specifies RSA encrypted as the
authentication method, or pre-share, which specifies pre-shared keys as
the authentication method.
— Group {1|2}—The default is 768-bit Diffie-Hellman. To specify the
Diffie-Hellman group identifier within an Internet Key Exchange
policy, options are 1, which specifies the 768-bit Diffie-Hellman group,
or 2, which specifies the 1024-bit Diffie-Hellman group.
— Lifetime (IKE policy)—The default is 86,400 seconds (once a day). To
specify the lifetime of an Internet Key Exchange security association
(SA), use the Lifetime Internet Security Association Key Management
Protocol policy configuration command. If two IPSec peers share
different lifetime values, the chosen value is the shortest lifetime.
Step 3 Set the ISAKMP identity (can be IP address or host name based).
crypto isakmp identity {address | hostname}
Step 4 Define transform sets.
A transform set represents a combination of security protocols and algo-
rithms. During the IPSec security association negotiation, the peers agree
to use a particular transform set for protecting a particular data flow.
To define a transform set, use the following commands starting in global
configuration mode:
crypto ipsec transform-set
transform-set-name transform1 [transform2 [transform3]]
This command puts you into the crypto transform configuration mode. Then
define the mode associated with the transform set.
Router(cfg-crypto-tran)# mode [tunnel | transport]
Step 5 Define crypto maps. Crypto maps tie the IPSec policies and SAs together.
crypto map name seq method [dynamic dynamic-map-name]
NOTE Crypto map entries created for IPSec pull together the various parts used to set up IPSec SAs,
including the following:
• Which traffic should be protected by IPSec (per a crypto access list)
• The granularity of the flow to be protected by a set of SAs
• Where IPSec-protected traffic should be sent (who the remote IPSec peer is)
• The local address to be used for the IPSec traffic](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-276-320.jpg)
![258 Chapter 5: Security Protocols
Example 5-20 displays the fact that the crypto map named “MAP1” is peered to a remote router,
131.108.255.2, and the access-list 100 defines what traffic will be encrypted across the tunnel.
IPSec is a large field, and to define every possible scenario would require a book in itself. What
is presented here in this guide is a conceptual overview of IPSec and a common configuration
example.
For more extensive details, visit www.cisco.com/univercd/cc/td/doc/product/software/
ios122/122cgcr/fsecur_c/index.htm.
For the written exam, expect to see scenarios of the variant presented in Figure 5-20 and
questions on terminology and the main characteristics of IPSec.
NOTE IPSec can also be supported over the Cisco software tunnel interface. Typically, the tunnel (IP
tunnel; GRE, for example) can be configured to carry non-IP traffic by defining a crypto map
to the tunnel interface and a crypto control list.
Table 5-9 defines some key configuration show and debug IPSec commands available on Cisco
IOS routers.
Table 5-9 IOS IPSec Configuration, Show, and Debug Commands
Command Description
crypto map map-name seq-num ipsec-isakmp Creates a crypto map entry.
[dynamic dynamic-map-name] [discover]
crypto ipsec transform-set transform-set-name Defines a transform set, an acceptable combination
transform1 [transform2 [transform3]] of security protocols and algorithms.
match address [access-list-id | name] This command is required for all static crypto map
entries.
crypto dynamic-map dynamic-map-name Use dynamic crypto maps to create policy
dynamic-seq-num templates that can be used when processing
negotiation requests for new SAs from a remote IP
Security peer, even if you do not know all the
crypto map parameters.
crypto ca authenticate name This command is required when you initially
configure CA support at your router.
crypto ca identity name Use this command to declare a CA.
crypto isakmp enable Globally enables Internet Key Exchange (IKE) at
your peer router.
Show crypto engine connection active View phase II SA and traffic sent.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-281-320.jpg)
![Scenario 5-1: Configuring Cisco Routers for IPSec 273
1 The following debug output is seen on R1 after the network administrator pings remote
network 131.108.100.1 from Router R2’s console port.
Why will the IPSec tunnel not negotiate properly?
R2#debug crypto engine
Crypto Engine debugging is on
R2#ping
Protocol [ip]:
Target IP address: 131.108.100.1
Repeat count [5]:
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]: y
Source address or interface: 131.108.200.1
Type of service [0]:
Set DF bit in IP header? [no]:
Validate reply data? [no]:
Data pattern [0xABCD]:
Loose, Strict, Record, Timestamp, Verbose[none]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 131.108.100.1, timeout is 2 seconds:
22:58:55: CryptoEngine0: generate alg parameter
22:58:55: CRYPTO_ENGINE: Dh phase 1 status: 0
22:58:55: CRYPTO_ENGINE: Dh phase 1 status: 0
22:58:55: CryptoEngine0: generate alg parameter
22:58:55: CryptoEngine0: create ISAKMP SKEYID for conn id 1
22:58:55: CryptoEngine0: generate hmac context for conn id 1.
22:58:55: %CRYPTO-4-IKMP_BAD_MESSAGE: IKE message from 131.108.255.1 failed it
s sanity check or is malformed....
Success rate is 0 percent (0/5)
R2#
2 What subnets will be encrypted between Routers R1 and R2?
3 What IOS command produced the following display and from which router?
Crypto Map "anyname1" 1 ipsec-isakmp
Peer = 131.108.255.2
Extended IP access list 100
access-list 100 permit ip 131.108.100.0 0.0.0.255 131.108.200.0 0.0.0.255
Current peer: 131.108.255.2
Security association lifetime: 4608000 kilobytes/180 seconds
PFS (Y/N): N
Transform sets={ anyname, }
Interfaces using crypto map anyname1:
Serial0/0
4 Will Host A be able to communicate with Host B or Host C? The following displays are
the IP routing tables on R1 and R2. (Assume the gateway configurations on the PCs are
correct.)
R1’s IP routing table:
R1>show ip route
Codes: C - connected, , O - OSPF,
131.108.0.0/16 is variably subnetted, 4 subnets, 2 masks
C 131.108.255.0/30 is directly connected, Serial0/0
O 131.108.200.0/24 [110/400] via 131.108.255.2, 00:52:00, Serial0/0
C 131.108.101.0/24 is directly connected, Ethernet0/1
C 131.108.100.0/24 is directly connected, Ethernet0/0](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-296-320.jpg)
![274 Chapter 5: Security Protocols
R2’s IP routing table:
R2>show ip route
Codes: C - connected, , O - OSPF
131.108.0.0/16 is variably subnetted, 4 subnets, 2 masks
C 131.108.255.0/30 is directly connected, Serial0/0
C 131.108.200.0/24 is directly connected, Ethernet0/0
O 131.108.101.0/24 [110/58] via 131.108.255.1, 00:52:09, Serial0/0
131.108.100.0/24 [110/58] via 131.108.255.1, 00:52:09, Serial0/0
5 To allow the IP subnet 131.108.101.0/24 attached to R1 Ethernet 0/1 interface to be
encrypted over the IPSec tunnel and to communicate with the remote PC IP address
131.108.200.5, what configuration changes are required on which router?](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-297-320.jpg)
![Scenario 5-1 Solutions 275
Scenario Answers
Scenario 5-1 Solutions
1 The following debug output advises the network administrator of the problem:
22:58:55: %CRYPTO-4-IKMP_BAD_MESSAGE: IKE message from 131.108.255.1 failed it
s sanity check or is malformed....
During the IKE negotiation, the router reports a message that identifies the fault as the
share password. R2 is configured with the password, CCIe (should match R1’s pre-shared
password set to CCIE). See example 5-21, and code line 7.
Changing the IKE password to CCIE with the IOS command, crypto isakmp key CCIE
address 131.108.255.1, the following debug output confirms the IPSec connections by
pinging from R2 Ethernet 0/0 IP address to R1 Ethernet 0/0 IP address:
R2#ping
Protocol [ip]:
Target IP address: 131.108.100.1
Repeat count [5]:
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]: y
Source address or interface: 131.108.200.1
Type of service [0]:
Set DF bit in IP header? [no]:
Validate reply data? [no]:
Data pattern [0xABCD]:
Loose, Strict, Record, Timestamp, Verbose[none]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 131.108.100.1, timeout is 2 seconds:
23:12:21: CryptoEngine0: generate alg parameter
23:12:21: CRYPTO_ENGINE: Dh phase 1 status: 0
23:12:21: CRYPTO_ENGINE: Dh phase 1 status: 0
23:12:21: CryptoEngine0: generate alg parameter
23:12:21: CryptoEngine0: create ISAKMP SKEYID for conn id 1
23:12:21: CryptoEngine0: generate hmac context for conn id 1
23:12:21: CryptoEngine0: generate hmac context for conn id 1
23:12:21: CryptoEngine0: generate hmac context for conn id 1
23:12:21: CryptoEngine0: clear dh number for conn id 1
23:12:22: CryptoEngine0: generate hmac context for conn id 1
23:12:22: validate proposal 0
23:12:22: validate proposal request 0
23:12:22: CryptoEngine0: generate hmac context for conn id 1.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 12/13/16 ms
R2#
The first Ping packet fails because the IPSec tunnel has not yet been created. Then, the
IPSec tunnel is successfully brought up between R1 and R2.
2 Access-list 100 on both routers defines the IP subnets that need to be encrypted between
R1 and R2. Packets flowing between subnets 131.108.100.0/24 and 131.108.200.0/24 will
be encrypted.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-298-320.jpg)
![UNIX 285
Table 6-1 DOS Versus UNIX Commands (Continued)
DOS/Windows NT Command UNIX Command Purpose
ping ip-address ping ip-address Pings a local or remote host.
tracert traceroute Windows sends ICMP requests
with varying time to live (TTL)
values. UNIX sends UDP
probes, varies the TTL values,
and watches for any ICMP
messages returned.
NOTE The Windows DOS-based attrib command is a widely used command that modifies file
attributes. In a Windows environment, the options include the following:
C: >help attrib
Displays or changes file attributes.
ATTRIB [+R | -R] [+A | -A ] [+S | -S] [+H | -H] [[drive:] [path] filename]
[/S [/D]]
+ Sets an attribute.
- Clears an attribute.
R Read-only file attribute.
A Archive file attribute.
S System file attribute.
H Hidden file attribute.
/S Processes matching files in the current folder
and all subfolders.
/D Processes folders as well
The attrib command allows files to be read only, archived, made a system file, or hidden.
In UNIX, you use the man command for command syntax help:
Simonunixhost% man
Usage: man [-M path] [-T macro-package] [ section ] name ...
or: man -k keyword ...
or: man -f file ...
UNIX Command Structure
UNIX servers and hosts are managed using files. To manage the files, you need to be aware of
the UNIX command structure.
A UNIX command contains three basic parts:
• Command
• Flags
• Arguments
Figure 6-1 displays the parts of a UNIX command.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-308-320.jpg)
![296 Chapter 6: Operating Systems and Cisco Security Applications
NBTSTAT [ [-a RemoteName] [-A IP address] [-c] [-n]
[-r] [-R] [-RR] [-s] [-S] [interval] ]
-a (adapter status) Lists the remote machine's name table given its name
-A (Adapter status) Lists the remote machine's name table given its
IP address.
-c (cache) Lists NBT's cache of remote [machine] names and their
IP addresses
-n (names) Lists local NetBIOS names.
-r (resolved) Lists names resolved by broadcast and via WINS
-R (Reload) Purges and reloads the remote cache name table
-S (Sessions) Lists sessions table with the destination IP addresses
-s (sessions) Lists sessions table converting destination IP
addresses to computer NETBIOS names.
-RR (ReleaseRefresh) Sends Name Release packets to WINs and then starts
Refresh
RemoteName Remote host machine name.
IP address Dotted decimal representation of the IP address.
interval Redisplays selected statistics, pausing interval seconds
between each display. Press Ctrl+C to stop redisplaying
statistics.
• ping—Provides a means to test and verify remote locations. An example ping to
www.cisco.com follows:
C:>ping www.cisco.com
Pinging www.cisco.com [198.133.219.25] with 32 bytes of data:
Reply from 198.133.219.25: bytes=32 time=182ms TTL=248
Reply from 198.133.219.25: bytes=32 time=180ms TTL=248
Reply from 198.133.219.25: bytes=32 time=180ms TTL=248
Reply from 198.133.219.25: bytes=32 time=181ms TTL=248
Ping statistics for 198.133.219.25:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 180ms, Maximum = 182ms, Average = 180ms
C:>
• tracert—Provides a method to list next hop addresses for remote networks. The following
is a sample Windows output when tracert routing to the URL www.smh.com.au:
C:>tracert www.smh.com.au
Tracing route to smh.com.au [203.26.51.42]
over a maximum of 30 hops:
1 <1 ms <1 ms <1 ms c6k-bbn1-vlan105.cisco.com [64.105.208.2]
2 <1 ms <1 ms <1 ms c6k-bbn1-msfc-v161.cisco.com [10.66.2.2]
3 <1 ms <1 ms <1 ms sydneycisco-wall-1-f0-1.cisco.com [10.166.128.15]
4 41 ms 236 ms <1 ms telstra-gw.cisco.com [103.141.98.141]
5 1 ms 1 ms <1 ms FastEthernet6-1-0.chw12.Sydney.telstra.net
[149.130.85.3]
6 1 ms 1 ms 1 ms FastEthernet1-0-0.ken4.Sydney.telstra.net
[203.50.19.14]
• route—Provides a method to define static routing entries (Windows NT supports RIP and
2000 supports OSPF). The following example adds a static route for the network
150.100.100.0/24 via the next hop address 131.108.1.1:
c:>route add 150.100.100.0 mask 255.255.255.0 131.108.1.1](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-319-320.jpg)
![Network Address Translation and Port Address Translation 327
For a more specific illustration, configure NAT on Router R1. In Figure 7-2, the NAT pool name
is going to be CCIE. (You can use any name you want.) Assume that the InterNIC has assigned
you the Class C address of 210.1.1.0/2424.
Your Internet service provider (ISP) has also supplied you the unique address 131.108.1.1/30
to use on your serial connection.
Example 7-3 provides a sample NAT configuration for this setup.
Example 7-3 Sample NAT Configuration on R1
hostname R1
ip nat pool CCIE 210.1.1.1 210.1.1.254 netmask 255.255.255.0
ip nat inside source 1 pool CCIE
interface ethernet0
ip address 10.99.34.1 255.255.255.0
ip nat inside
interface serial 0
ip address 131.108.1.1 255.255.255.252
ip address 210.1.1.1 255.255.255.0 secondary
ip nat outside
access-list 1 permit 10.99.34.0 0.0.0.255
It is assumed that you have an IP routing protocol to advertise the IP networks shown in the
sample, which are 131.108.1.0/30 and 210.1.1.0/24, to the remote ISP router through R1’s
Serial 0 interface.
The configuration shown in Example 7-3 translates the inside addresses 10.99.34.0/24 into
globally unique addresses ranging from 210.1.1.1/24 to 210.1.1.254.
Monitoring NAT Operations with show Commands
To monitor the operation of NAT, you can use the following commands:
show ip nat translation [verbose]
show ip nat statistics
The show ip nat translation command displays the current active transactions. The show ip
nat statistics command displays NAT statistics, such as how many translations are currently
taking place.
There are four different versions of NAT translations:
• Static NAT—Maps an unregistered IP address to a registered IP address on a one-to-one
basis. This is particularly useful when a device needs to be accessible from outside the
network to an internal unregistered address.
• Dynamic NAT—Maps an unregistered IP address to a registered IP address from a group
of registered IP addresses.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-350-320.jpg)
![Cisco Private Internet Exchange (PIX) 333
Table 7-3 describes the PIX command nameif as documented on the Cisco
documentation CD.
Table 7-3 nameif Command and Required Fields
Syntax Description
hardware_id The hardware name for the network interface that specifies the interface’s slot
location on the PIX Firewall motherboard. Interface boards are numbered from the
leftmost slot nearest the power supply as slot 0. The internal network interface
must be in slot 1. The lowest security_level external interface board is in slot 0,
and the next lowest security_level external interface board is in slot 2.
Possible choices are Ethernet for Ethernet or Token-ring for Token Ring.
The internal interface is ethernet1. These names can be abbreviated with any
leading characters in the name; for example, ether1, e2, token0, or t0.
if_name A name for the internal or external network interface of up to 48 characters in
length. This name can be uppercase or lowercase. By default, the PIX Firewall
names the inside interface inside, the outside interface outside, and any perimeter
interface intfn, where n is 2 through 5.
security_level Either 0 for the outside network or 100 for the inside network. Perimeter interfaces
can use any number between 1 and 99. By default, the PIX Firewall sets the
security level for the inside interface to security100, and the outside interface to
security0. The first perimeter interface is initially set to security10, the second
to security15, the third to security20, and the fourth perimeter interface to
security25 (a total of 6 interfaces are permitted, with a total of 4 perimeter
interfaces permitted).
Step 3 Identify the hardware interfaces, speed, and duplex type installed with the
following interface command:
interface hardware_id [hardware_speed] [shutdown]
In Figure 7-5, the following commands are configured:
interface ethernet0 10full
interface ethernet1 10full
Table 7-4 defines and describes the options for the interface command, as
documented on the Cisco documentation CD.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-356-320.jpg)
![334 Chapter 7: Security Technologies
Table 7-4 interface Command Options
Option Description
hardware_id Identifies the network interface type. Possible values are ethernet0, ethernet1 to
ethernetn, gb-ethernetn, fddi0 or fddi1, token-ring0, and token-ring1 to token-
ringn, depending on how many network interfaces are in the firewall.
hardware_speed Network interface speed (optional). Do not specify a hardware_speed for a Fiber
Distributed Data Interface (FDDI) interface.
Possible Ethernet values are as follows:
10baset—Set for 10 Mbps Ethernet half-duplex communication.
10full—Set for 10 Mbps Ethernet full-duplex communication.
100basetx—Set for 100 Mbps Ethernet half-duplex communication.
100full—Set for 100 Mbps Ethernet full-duplex communication.
1000sxfull—Set for 1000 Mbps Gigabit Ethernet full-duplex operation.
1000basesx—Set for 1000 Mbps Gigabit Ethernet half-duplex operation.
1000auto—Set for 1000 Mbps Gigabit Ethernet to auto-negotiate full or half
duplex.
Aui—Set 10 for Mbps Ethernet half-duplex communication with an AUI cable
interface.
Auto—Set Ethernet speed automatically. The auto keyword can be used only with
the Intel 10/100 automatic speed sensing network interface card, which shipped
with the PIX Firewall units manufactured after November 1996.
Bnc—Set for 10 Mbps Ethernet half-duplex communication with a BNC cable
interface.
Possible Token Ring values are as follows:
4mbps—4 Mbps data transfer speed. You can specify this as 4.
16mbps—(Default) 16 Mbps data transfer speed. You can specify this as 16.
shutdown Disables an interface.
Step 4 Define the inside and outside IP addresses.
The ip address if_name ip_address [netmask] command lets you assign an
IP address to each interface.
Use the show ip command to view which addresses are assigned to the
network interfaces.
In Figure 7-5, the IP address assignment is defined as follows:
ip address inside 201.201.201.1 255.255.255.0
ip address outside 131.108.1.1 255.255.255.0](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-357-320.jpg)
![Cisco Private Internet Exchange (PIX) 335
Table 7-5 defines the options and meaning of the interface command.
Table 7-5 interface Command
Option Description
if_name The internal or external interface name designated by the nameif command
ip_address PIX Firewall unit’s network interface IP address
netmask Network mask of ip_address
Step 5 Define the NAT with the nat command.
The nat command lets you enable or disable address translation for one or
more internal addresses. Address translation means that when a host starts an
outbound connection, the IP addresses in the internal network are translated
into global addresses. NAT lets your network have any IP addressing scheme,
and the firewall protects these addresses from visibility on the external
network.
The command syntax is as follows:
nat [(if_name)] nat_id local_ip [netmask [max_conns [em_limit]]] [norandomseq]
In Figure 7-5, the following pool is assigned to the PIX:
nat (inside) 1 0.0.0.0 0.0.0.0
This command enables all inside hosts to access the Internet.
Table 7-6 defines the options of the nat command, as documented on the
Cisco documentation CD.
Table 7-6 nat Command Options
Option Description
if_name Any internal network interface name.
nat_id The nat_id is an arbitrary positive number between 0 and 2 billion.
Specify 0 with IP addresses and netmasks to identify internal networks that desire
only outbound identity address translation. Use 0 with the access-list option to
specify traffic that should be exempt from NAT. The access list should already be
defined, otherwise PIX gives an error message.
access-list Associate an access-list command statement to the nat 0 command.
local_ip Internal network IP address to be translated. You can use 0.0.0.0 to allow all hosts
to start outbound connections. The 0.0.0.0 local_ip can be abbreviated as 0.
netmask Network mask for local_ip. You can use 0.0.0.0 to allow all outbound connections
to translate using IP addresses from the global pool.
continues](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-358-320.jpg)
![336 Chapter 7: Security Technologies
Table 7-6 nat Command Options (Continued)
Option Description
max_conns The maximum TCP connections permitted from the interface you specify.
em_limit The embryonic connection limit. The default is 0, which means unlimited
connections. Set it lower for slower systems and higher for faster systems.
Norandomseq Do not randomize the TCP packet’s sequence number. Only use this option if
another inline firewall is also randomizing sequence numbers and the result is
scrambling the data. Use of this option opens a security hole in the PIX Firewall.
Step 6 Define the global pool.
The global command defines a pool of global addresses. The global
addresses in the pool provide an IP address for each outbound connection,
and for those inbound connections resulting from outbound connections.
If the nat command is used, you must also use the global command.
Basically, when an outbound IP packet is sent from the inside network, the
PIX will extract the source address and compare that address to the list of
current NAT translations. If there is no entry, a new entry is created. If a NAT
translation entry already exists, the packet is forwarded.
The PIX syntax for the global command is defined as follows:
global [if_name] nat_id global_ip [-global_ip] [netmask global_mask]
In Figure 7-5, the pool of address is defined as follows:
global (outside) 1 192.192.1.2-192.192.1.30 netmask 255.255.255.224
The pool of addresses is typically assigned to you by the InterNIC or your ISP.
Table 7-7 defines the options of the global command, as documented on the
Cisco documentation CD.
Table 7-7 global Command Options
Option Description
if_name The external network where you use these global addresses.
nat_id A positive number shared with the nat command that groups the nat and global
command statements together. The valid ID numbers can be any positive number
up to 2,147,483,647.
global_ip One or more global IP addresses that the PIX Firewall shares among its
connections.
If the external network is connected to the Internet, each global IP address must be
registered with the Network Information Center (NIC). You can specify a range of
IP addresses by separating the addresses with a dash (-).](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-359-320.jpg)
![Cisco Private Internet Exchange (PIX) 337
Table 7-7 global Command Options (Continued)
Option Description
global_ip You can create a PAT global command statement by specifying a single IP
(Continued) address. You can have one PAT global command statement per interface. A PAT
can support up to 65,535 xlate objects.
netmask Reserved word that prefaces the network global_mask variable.
global_mask The network mask for global_ip. If subnetting is in effect, use the subnet mask;
for example, 255.255.255.128. If you specify an address range that overlaps
subnets, global will not use the broadcast or network addresses in the pool of
global addresses. For example, if you use 255.255.255.224 and an address range
of 209.165.201.1 to 209.165.201.30, the 209.165.201.31 broadcast address and
the 209.165.201.0 network address will not be included in the pool of global
addresses.
Step 7 Finally, define how to route IP data with the route command.
Use the route command to enter a default or static route for an interface. The
PIX syntax is as follows:
route if_name ip_address netmask gateway_ip [metric]
Configuring Static Routing on a PIX Firewall
Figure 7-5 defines all routes via the perimeter router as follows:
route outside 0.0.0.0 0.0.0.0 131.108.1.2
Table 7-8 defines the options of the route command, as documented on the Cisco
documentation CD.
Table 7-8 route Command Options
Option Description
if_name The internal or external network interface name.
ip_address The internal or external network IP address. Use 0.0.0.0 to specify a default route.
You can abbreviate the 0.0.0.0 IP address as 0.
netmask Specify a network mask to apply to ip_address. Use 0.0.0.0 to specify a default
route. The 0.0.0.0 netmask can be abbreviated as 0.
gateway_ip Specify the gateway router’s IP address (the next hop-address for this route).
metric Specify the number of hops to gateway_ip. In Figure 7-5, this is 1.
Example 7-4 displays the full working configuration of the PIX in Figure 7-5. The highlighted
portions of this display are configuration commands we have entered, and the nonhighlighted
portions are default configurations. One of the advantages of the PIX Firewall, like the Catalysts](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-360-320.jpg)
![Cisco Private Internet Exchange (PIX) 339
Example 7-4 PIX Full Working Configuration (Continued)
no snmp-server contact
snmp-server community public
no snmp-server enable traps
telnet timeout 5
terminal width 80
: end
Miscellaneous PIX Firewall Commands Three other important commands that are
commonly used in PIX configurations are the static, conduit, and alias commands.
The static command creates a permanent mapping (Cisco documentation names or calls this a
translation slot or xlate) between a local IP address and a global IP address. Use the static and
conduit commands when you are accessing an interface of a higher security level from an
interface of a lower security level; for example, when accessing the inside from the outside
interface.
The command syntax is as follows:
static [(internal_if_name, external_if_name)] global_ip local_ip [netmask network_mask]
[max_conns [em_limit]] [norandomseq]
Table 7-9 defines the options of the route command, as documented on the Cisco
documentation CD.
Table 7-9 route Command Options
Option Description
internal_if_name The internal network interface name. The higher-security-level interface you are
accessing.
external_if_name The external network interface name. The lower-security-level interface you are
accessing.
global_ip A global IP address. This address cannot be a PAT IP address. The IP address on
the lower-security-level interface you are accessing.
local_ip The local IP address from the inside network. The IP address on the higher-
security-level interface you are accessing.
netmask Reserve word required before specifying the network mask.
network_mask The network mask pertains to both global_ip and local_ip. For host addresses,
always use 255.255.255.255. For network addresses, use the appropriate class
mask or subnet mask; for example, for Class A networks, use 255.0.0.0. An
example subnet mask is 255.255.255.224.
continues](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-362-320.jpg)
![340 Chapter 7: Security Technologies
Table 7-9 route Command Options (Continued)
Option Description
max_conns The maximum number of connections permitted through the static connection at
the same time.
em_limit The embryonic connection limit. An embryonic connection is one that has started
but not yet completed. Set this limit to prevent attack by a flood of embryonic
connections. The default is 0, which means unlimited connections.
norandomseq Do not randomize the TCP/IP packet’s sequence number. Use only this option if
another inline firewall is also randomizing sequence numbers and the result is
scrambling the data. Use of this option opens a security hole in the PIX Firewall.
An example of the command is as follows:
static (inside,outside) 192.192.1.33 201.201.201.10
The static command should be used in conjunction with either conduit or access-list.
A conduit command statement creates an exception to the PIX Firewall Adaptive Security
mechanism by permitting connections from one firewall network interface to access hosts on
another.
The clear conduit command removes all conduit command statements from your
configuration.
The command syntax is defined as follows:
conduit {permit | deny} protocol global_ip global_mask [operator port [port]]
foreign_ip foreign_mask [operator port [port]]
Table 7-10 displays the options and command syntax for the conduit command, as documented
on the Cisco documentation CD.
Table 7-10 conduit Command Options
Option Description
permit Permits access if the conditions are matched.
deny Denies access if the conditions are matched.
protocol Specifies the transport protocol for the connection. Possible literal values are
icmp, tcp, udp, or an integer in the range 0 through 255, representing an IP
protocol number. Use ip to specify all transport protocols.
global_ip A global IP address previously defined by a global or static command. You can use
any if the global_ip and global_mask are 0.0.0.0 0.0.0.0. The any option applies
the permit or deny parameters to the global addresses.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-363-320.jpg)
![342 Chapter 7: Security Technologies
Advanced Cisco PIX Commands
Table 7-11 summarizes some of the other useful features on a Cisco PIX Firewall, as
documented on the Cisco Documentation CD.
Table 7-11 PIX Firewall Advanced Features
Command Description
ca Configure the PIX Firewall to interoperate with a
Certification Authority (CA).
clear xlate Clears the contents of the translation slots.
show xlate Displays NAT translations. The show xlate command
displays the contents of only the translation slots.
crypto dynamic-map Create, view, or delete a dynamic crypto map entry.
failover [active] Use the failover command without an argument after you
connect the optional failover cable between your primary
firewall and a secondary firewall.
fixup protocol The fixup protocol commands let you view, change, enable,
or disable the use of a service or protocol through the PIX
Firewall.
kill Terminate a Telnet session. Telnet sessions to the PIX must
be enabled.
telnet ip_address [netmask] [if_name] Specify the internal host for PIX Firewall console access
via Telnet from inside hosts only.
Cisco PIX Firewall Software Features
A list of the current features of the Cisco PIX Firewall product follows:
• State-of-the-art Adaptive Security Algorithm (ASA) and stateful inspection firewalling.
• Cut-through proxy authenticates and authorizes connections, while enhancing
performance.
• Easy-to-use web-based interface for managing PIX Firewalls remotely; the web-based
interface is not a suggested practice by Cisco for medium to large networks.
• Support for up to 10 Ethernet interfaces ranging from 10-BaseT, 10/100 Fast Ethernet to
Gigabit Ethernet.
• Stateful firewall failover capability with synchronized connection information and
product configurations.
• True Network Address Translation (NAT), as specified in RFC 1631.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-365-320.jpg)
![Foundation Summary 353
Table 7-14 Cisco PIX Model Numbers
PIX 501
PIX 506/506E
PIX 515/515E
PIX 520 (in current CCIE lab)
PIX 525
PIX 535
Table 7-15 PIX Configuration Steps
Step Description
1 Name the inside/outside interfaces and security levels.
2 Identify the hardware interfaces and speed/duplex.
3 Define the IP address for inside and outside interfaces.
4 Define NAT/PAT.
5 Define the global pool.
6 Define the IP route path.
7 Define static/conduits or static/access lists (for outside networks to access inside hosts or
networks).
Table 7-16 PIX Command Options
Option Description
ca Configures the PIX Firewall to interoperate with a Certification Authority
(CA).
clear xlate Clears the contents of the translation slots.
show xlate Displays NAT translations. The show xlate command displays the contents of
only the translation slots.
crypto dynamic-map Create, view, or delete a dynamic crypto map entry with this command.
failover [active] Use the failover command without an argument after you connect the
optional failover cable between your primary firewall and a secondary
firewall.
fixup protocol The fixup protocol commands let you view, change, enable, or disable the
use of a service or protocol through the PIX Firewall.
kill Terminate a Telnet session. Telnet sessions to the PIX must be enabled and
are sent as clear text.
telnet ip_address Specify the internal host for PIX Firewall console access through Telnet.
[netmask] [if_name]](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-376-320.jpg)
![378 Chapter 8: Network Security Policies, Vulnerabilities, and Protection
The service category is quite useful. Essentially, enabling it means your syslog entries will be
numbered to ensure that they are not tampered with. R1 is configured for TACACS via the
remote host 131.108.1.1.
Example 8-7 configures R1 for AAA.
Example 8-7 AAA Configuration
username cisco pass ciSc0
aaa new-model
aaa authentication login default group tacacs+ local-case
aaa authentication enable default group tacacs+ enable
aaa authorization commands 15 default group tacacs+ local
aaa accounting exec default stop-only group tacacs+
aaa accounting commands 15 default stop-only group tacacs+
aaa accounting network default stop-only group tacacs+
tacacs-server host 131.108.1.1
tacacs-server key myguitarrocksthisworld
Example 8-7 configures R1 for AAA authentication in the event TACACS+ fails to use local
authentication with a case-sensitive password to keep hackers guessing.
By default, Cisco IOS permits a number of default services. Example 8-8 disables some
common services.
Example 8-8 Disable Services on by Default
no ip http server
no ip finger
no service pad
no ip source-route
no ip bootp server
Example 8-8 disables R1 for an HTTP server. The finger command service allows remote users
to view the output (equivalent to the show users [wide] command). When ip finger is config-
ured, the router responds to a telnet a.b.c.d finger command from a remote host by immediately
displaying the output of the show users command and then closing the connection. You should
turn this service off. The service pad enables all packets to be assembled or disassembled
(PAD) between PAD devices and access servers. The command no ip source-route causes the
system to discard any IP datagram containing a source-route option. When you disable the
BOOTP server, access to the BOOTP ports causes the Cisco IOS Software to send an “ICMP
port unreachable” message to the sender and discard the original incoming packet.
Example 8-9 enables TCP intercept.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-401-320.jpg)
![Chapter 2 “Do I Know This Already?” Quiz Answers 497
26 What best describes the ARP process?
a. DNS resolution
b. Mapping an IP address to a MAC address
c. Mapping a next-hop address to outbound interface on a Cisco router
d. Both a and b
Answer: b
ARP maps an IP address to a MAC address.
27 If two Cisco routers are configured for HSRP and one router has a default priority of 100
and the other 99, which router assumes the role of active router?
a. The default priority cannot be 100.
b. The router with a higher priority.
c. The router with the lowest priority.
d. Neither router because Cisco routers do not support HSRP; only clients do.
Answer: b
The highest priority assumes the role of active router.
28 A Cisco router has the following route table:
R1#show ip route
131.108.0.0/16 is variably subnetted, 17 subnets, 2 masks
C 131.108.255.0/24 is directly connected, Serial0/0
C 131.108.250.0/24 is directly connected, Serial0/1
O 131.108.254.0/24 [110/391] via 131.108.255.6, 03:33:03, Serial0/1
[110/391] via 131.108.255.2, 03:33:03, Serial0/0
R 131.108.254.0/24 [120/1] via 131.108.255.6, 03:33:03, Serial0/1
[120/1] via 131.108.255.2, 03:33:03, Serial0/
What is the preferred path to 131.108.254.0/24? (Choose the best two answers.)
a. Via Serial 0/0
b. Via Serial 0/1
c. None
d. To null0
Answers: a and b
OSPF is chosen because of the lower administrative distance of 110 compared to
RIP’s 120. Also notice OSPF load balancing between Serial0/0 and Serial0/1. (The
written examination always advises you how many answers to select. Practice on the
CD provided.)](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-422-320.jpg)
![Chapter 3 “Do I Know This Already?” Quiz Answers 509
4 What does the following Global IOS configuration line accomplish?
ip host SimonisaCCIE 131.108.1.1 131.108.1.2
a. Defines the router name as SimonisaCCIE
b. Defines a local host name, SimonisaCCIE, mapped to IP addresses 131.108.1.1 and
131.108.1.2
c. Configures the IOS router for remote routing entries 131.108.1.1 and 131.108.1.2
d. Not a valid IOS command
e. Configures the local routers with the IP address 131.108.1.1 and 131.108.1.2 on
boot up
Answer: b
The ip host name ip address1 [ipaddress2 ipaddress3 ipaddress4 ipaddress5 ipaddress6
ipaddress7 ipaddress8] command configures a local address lookup for the name
SimonisaCCIE. Up to 8 addresses can be used. The router will try 131.108.1.1 first
and, if no response is made by the remote host, the second address, 131.108.1.2, will
be attempted from the command-line interface (CLI).
5 TFTP uses what predefined UDP port number?
a. 21
b. 22
c. 23
d. 53
e. 69
Answer: e
TFTP uses UDP port number 69.
6 What IOS command will copy an IOS image from the current system flash to a TFTP
server?
a. copy tftp image:
b. copy flash tftp
c. copy tftp flash
d. copy tftp tftp
Answer: b
To copy an IOS image from the routers to system flash, the correct IOS command is
copy flash tftp.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-434-320.jpg)
![Chapter 3 Q & A Answers 515
22 To restrict SNMP managers from the source network 131.108.1.0/30, what IOS command
is required?
a.
ip http enable 131.108.1.1 131.108.1.2
b.
snmp community 131.108.1.1 131.108.1.2
c.
snmp-server community SimonisCool ro 4
access-list 4 permit 131.108.1.0 0.0.0.252
d.
snmp-server community SimonisCool ro 4
e.
snmp-server community SimonisCool ro 1
access-list 11 permit 131.108.1.0 0.0.0.252
Answer: c
The SNMP server community name must be defined with the following command:
snmp-server community string ro access-list-number
The access list number definition must follow (in this case, number 4). The access list
range is between 1 and 99 only.
Chapter 3 Q & A Answers
1 According to RFC 1700, what is the well-known TCP/UDP port used by DNS?
Answer: RFC 1700 defines the well-known ports for the whole TCP/IP protocol
suite. For DNS, the well-known port for TCP/UDP is number 53.
2 What does the IOS command no ip domain-lookup accomplish?
Answer: This IOS command disables DNS queries for network administrators
connected to a Cisco console or vty line.
3 What is the correct IOS syntax to specify local host mapping on a Cisco router?
Answer: Local host mappings to IP addresses are accomplished using the following
IOS command:
ip host name [tcp-port-number] ip address1 [ip address2...ip address8]
Up to eight IP addresses can be assigned to one name.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-440-320.jpg)
![518 Appendix A: Answers to Quiz Questions
19 What IOS command can be implemented to restrict SNMP access to certain networks by
applying access lists? Can you apply standard, extended, or both?
Answer: The IOS command is as follows:
snmp-server community string [view view-name] [ro | rw] [number]
You can only apply a standard access-list list with the above command.
number refers to a standard access list, ranging from 1 to 99 only, that defines
the remote hosts or subnets that are permitted SNMP access. The correct SNMP
community string must also be correctly configured on the SNMP manger and
agent to allow SNMP communication.
20 Does TFTP have a mechanism for username and password authentication?
Answer: TFTP is a connectionless protocol (UDP) that has no method to authenticate
username or password. The TFTP packet format has no field enabling the username
or password to be exchanged between two TCP/IP hosts. TFTP security (configurable
on UNIX and Windows platforms) on the TFTP server is accomplished by allowing
a predefined file on the server to be copied to the host TFTP server.
21 Can you use your Internet browser to configure a Cisco router? If so, how?
Answer: To view the router’s home page, use a Web browser pointed to http://a.b.c.d,
where a.b.c.d is the IP address of your router or access server. If a name has been set,
use http://router-name, and use the DNS server to resolve the IP address.
To enable HTTP on a Cisco router, use the IOS command ip http in global
configuration mode.
22 A network administrator defines a Cisco router to allow HTTP requests but forgets to add
the authentication commands. What is the default username and password pairing that
allows HTTP requests on the default TCP port 80? Can you predefine another TCP port
for HTTP access other than port 80?
Answer: By default Cisco IOS routers configured for HTTP access use the router’s
local host name as the username and the enable or secret password as the password.
The IOS command ip http [0-65535] allows the network administrator to define a
new port number other than 80, which is the default setting.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-443-320.jpg)
![Chapter 4 “Do I Know This Already?” Quiz Answers 519
Chapter 4 “Do I Know This Already?” Quiz Answers
1 What IOS command will display the System Flash?
a. show flash
b. show system flash
c. show memory
d. show process flash
Answer: a
The show flash IOS command displays the System Flash:
R1#show flash
System flash directory:
File Length Name/status
1 11600424 c2600-ik8o3s-mz.122-2.T.bin
[11600488 bytes used, 5176728 available, 16777216 total]
16384K bytes of processor board System flash (Read/Write)
R1#
2 The network administrator has forgotten the enable password and all passwords are
encrypted. What should the network administrator do to recover the password without
losing the current configuration?
a. Call the TAC and ask for a special back door password.
b. Call the TAC and raise a case to supply the engineering password.
c. Reboot the router, press the break key during the reload, and enter ROM mode and
change the configuration register.
d. Reboot the router, press the break key during the reload, enter ROM mode and
change the configuration register, and when the router reloads, remove the old config-
uration.
Answer: c
The TAC will not supply any passwords. The steps required include issuing the break
key and modifying the configuration register, but the aim is to not lose the initial
configuration, so answer d is incorrect.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-444-320.jpg)
![522 Appendix A: Answers to Quiz Questions
9 Where is the startup configuration stored on a Cisco router?
a. In the cam table
b. NVRAM
c. RAM
d. Flash
e. slot0:
Answer: b
The startup configuration is usually stored in the NVRAM. You can store the file on
a TFTP server, as well.
10 Which of the following statements is true?
a. The enable secret command overrides the enable password command.
b. The enable command overrides the enable secret password command.
c. Enable passwords cannot be used when the secret password is used.
d. Both a and c are true.
Answer: a
The enable secret command overrides the enable password command when
configured concurrently.
11 A Cisco router has the following configuration:
line vty 0 4
login
What will happen when you Telnet to the router?
a. You will be prompted for the login password.
b. You will enter EXEC mode immediately.
c. You cannot access the router without the password set.
d. More configuration required.
Answer: c
Without the password configured, you cannot enter EXEC mode. The router will
advise the Telnet user that the password is not set and disconnect the session, as
follows:
R1#131.108.1.1
Trying 131.108.1.1 ... Open
Password required, but none set
[Connection to 131.108.1.1 closed by foreign host]](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-447-320.jpg)
![Chapter 4 Q & A Answers 525
Chapter 4 Q & A Answers
1 Where is the running configuration stored on a Cisco router?
Answer: The configuration is stored in the Random Access Memory (RAM). For
all newer Cisco hardware platforms, the memory location where the running
configuration is stored is called the Dynamic Random-Access Memory (DRAM).
2 What IOS command displays the startup configuration?
Answer: The IOS command show startup-config or show config will display the
configuration stored in NVRAM.
3 What IOS command provides the following output?
System flash directory:
File Length Name/status
1 9558976 c2500-ajs40-l.12-17.bin
[9559040 bytes used, 7218176 available, 16777216 total]
16384K bytes of processor board System flash
Answer: The IOS command to display the System Flash is show flash.
4 What configuration register will enable a Cisco router to ignore the startup configuration?
Answer: 0x2142 will set the IOS to ignore the configuration stored in NVRAM;
typically, this configuration register is used for password recovery.
5 To copy the startup configuration to the running configuration, what IOS command or
commands are used?
Answer: copy startup-config running-config.
6 What is the range for standard and extended IP access lists on Cisco IOS routers?
Answer: Standard IP access lists range from 1-99 and 1300-1999. Extended access
lists range from 100-199 and 2000-2699.
7 What command display the IP access lists configured on a Cisco router?
Answer: show ip access-lists will display all configured IP access lists. The show
access-lists IOS command displays all configured access lists, not just IP access lists.
8 How do you disable all debug commands currently enabled on a Cisco router, assuming
you are not sure what debug commands are enabled?
Answer: undebug all (or u all in shorthand). You can also use the [no] debug <specific
debug-enabled commands> for each specific debug that has been enabled. To quickly
disable all debug commands, undebug all is typically used.](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-450-320.jpg)
![540 Appendix A: Answers to Quiz Questions
• Attribute type 7—Protocol (defines what framing is required; for example, PPP
is defined when this attribute is set to 1, SLIP is 2)
• Attribute type 8—IP address (defines the IP address to be used by the
remote user)
• Attribute type 9—IP subnet mask (defines the subnet mask to be used by the
remote user)
• Attribute type 10—Routing
• Attribute type 13—Compression
• Attribute type 19—Callback number
• Attribute type 20—Callback ID
• Attribute type 26—Vendor-specific (Cisco [vendor-ID 9] uses one defined
option, vendor type 1, named cisco-avpair)
7 What protocols does RADIUS use when sending messages between the server and client?
Answer: RADIUS transports through UDP destination port number 1812.
8 What predefined destination UDP port number is RADIUS accounting information sent to?
Answer: UDP port 1646
9 What does the following command accomplish on a Cisco IOS router?
aaa authentication ppp user-radius if-needed group radius
Answer: The aaa authentication ppp user-radius if-needed group radius command
configures the Cisco IOS software to use RADIUS authentication for lines using PPP
with CHAP or PAP, if the user has not already been authorized. If the EXEC facility
has authenticated the user, RADIUS authentication is not performed. User-radius is
the name of the method list that defines RADIUS as the if-needed authentication
method.
10 What is the RADIUS server IP address and key for the following configuration?
radius-server host 3.3.3.3
radius-server key GuitarsrocKthisplaneT
Answer: The radius-server host command defines the RADIUS server host’s IP
address. The IP address is 3.3.3.3.
The radius-server key command defines the shared secret text string between the
NAS and the RADIUS server host. The key is case-sensitive like all passwords on
Cisco IOS devices, so the key is defined as GuitarsrocKthisplaneT.
11 TACACS+ is transported over what TCP destination port number?
Answer: TCP port 49](https://image.slidesharecdn.com/cciesecurity-100720081137-phpapp01/85/Ccie-security-465-320.jpg)
Ccie security
- 2. CCIE Self-Study CCIE Security Exam Certification Guide Henry Benjamin Cisco Press Cisco Press 201 West 103rd Street Indianapolis, IN 46290 USA
- 3. ii CCIE Self-Study CCIE Security Exam Certification Guide Henry Benjamin Copyright © 2003 Cisco Systems, Inc. Published by: Cisco Press 201 West 103rd Street Indianapolis, IN 46290 USA All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or by any information storage and retrieval system, without written permission from the publisher, except for the inclusion of brief quotations in a review. Printed in the United States of America 1 2 3 4 5 6 7 8 9 0 First Printing April 2003 Library of Congress Cataloging-in-Publication Number: 2002104850 ISBN: 1-58720-065-1 Warning and Disclaimer This book is designed to provide information about the CCIE Security written exam. Every effort has been made to make this book as complete and as accurate as possible, but no warranty or fitness is implied. The information is provided on an “as is” basis. The authors, Cisco Press, and Cisco Systems, Inc., shall have neither liability nor responsibility to any person or entity with respect to any loss or damages arising from the information contained in this book or from the use of the discs or programs that may accompany it. The opinions expressed in this book belong to the author and are not necessarily those of Cisco Systems, Inc. Trademark Acknowledgments All terms mentioned in this book that are known to be trademarks or service marks have been appropriately capitalized. Cisco Press or Cisco Systems, Inc. cannot attest to the accuracy of this information. Use of a term in this book should not be regarded as affecting the validity of any trademark or service mark. Feedback Information At Cisco Press, our goal is to create in-depth technical books of the highest quality and value. Each book is crafted with care and precision, undergoing rigorous development that involves the unique expertise of members from the professional technical community. Readers’ feedback is a natural continuation of this process. If you have any comments regarding how we could improve the quality of this book, or otherwise alter it to better suit your needs, you can contact us through e-mail at feedback@ciscopress.com. Please make sure to include the book title and ISBN in your message. We greatly appreciate your assistance.
- 4. iii Publisher John Wait Editor-in-Chief John Kane Executive Editor Brett Bartow Cisco Representative Anthony Wolfenden Cisco Press Program Manager Sonia Torres Chavez Cisco Marketing Communications Manager Tom Geitner Cisco Marketing Program Manager Edie Quiroz Managing Editor Patrick Kanouse Development Editor Andrew Cupp Project Editor San Dee Phillips Copy Editor Marcia Ellett Technical Editors Gert De Laet, Anand Deveriya, Charles Resch, Gert Schauwers Team Coordinator Tammi Ross Book Designer Gina Rexrode Cover Designer Louisa Adair Compositor Octal Publishing, Inc. Indexer Brad Herriman Corporate Headquarters European Headquarters Americas Headquarters Asia Pacific Headquarters Cisco Systems, Inc. Cisco Systems Europe Cisco Systems, Inc. Cisco Systems Australia, 170 West Tasman Drive 11 Rue Camille Desmoulins 170 West Tasman Drive Pty., Ltd San Jose, CA 95134-1706 92782 Issy-les-Moulineaux San Jose, CA 95134-1706 Level 17, 99 Walker Street USA Cedex 9 USA North Sydney http://www.cisco.com France http://www.cisco.com NSW 2059 Australia Tel: 408 526-4000 http://www-europe.cisco.com Tel: 408 526-7660 http://www.cisco.com 800 553-NETS (6387) Tel: 33 1 58 04 60 00 Fax: 408 527-0883 Tel: +61 2 8448 7100 Fax: 408 526-4100 Fax: 33 1 58 04 61 00 Fax: +61 2 9957 4350 Cisco Systems has more than 200 offices in the following countries. Addresses, phone numbers, and fax numbers are listed on the Cisco Web site at www.cisco.com/go/offices Argentina • Australia • Austria • Belgium • Brazil • Bulgaria • Canada • Chile • China • Colombia • Costa Rica • Croatia • Czech Republic • Denmark • Dubai, UAE • Finland • France • Germany • Greece • Hong Kong Hungary • India • Indonesia • Ireland • Israel • Italy • Japan • Korea • Luxembourg • Malaysia • Mexico The Netherlands • New Zealand • Norway • Peru • Philippines • Poland • Portugal • Puerto Rico • Romania Russia • Saudi Arabia • Scotland • Singapore • Slovakia • Slovenia • South Africa • Spain • Sweden Switzerland • Taiwan • Thailand • Turkey • Ukraine • United Kingdom • United States • Venezuela • Vietnam Zimbabwe Copyright © 2000, Cisco Systems, Inc. All rights reserved. Access Registrar, AccessPath, Are You Ready, ATM Director, Browse with Me, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, CiscoLink, the Cisco NetWorks logo, the Cisco Powered Network logo, Cisco Systems Networking Academy, Fast Step, FireRunner, Follow Me Browsing, FormShare, GigaStack, IGX, Intelligence in the Optical Core, Internet Quotient, IP/VC, iQ Breakthrough, iQ Expertise, iQ FastTrack, iQuick Study, iQ Readiness Scorecard, The iQ Logo, Kernel Proxy, MGX, Natural Network Viewer, Network Registrar, the Networkers logo, Packet, PIX, Point and Click Internetworking, Policy Builder, RateMUX, ReyMaster, ReyView, ScriptShare, Secure Script, Shop with Me, SlideCast, SMARTnet, SVX, TrafficDirector, TransPath, VlanDirector, Voice LAN, Wavelength Router, Workgroup Director, and Workgroup Stack are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, Empowering the Internet Generation, are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, Cisco, the Cisco Certified Internetwork Expert Logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Collision Free, Enterprise/Solver, EtherChannel, EtherSwitch, FastHub, FastLink, FastPAD, IOS, IP/TV, IPX, LightStream, LightSwitch, MICA, NetRanger, Post-Routing, Pre-Routing, Registrar, StrataView Plus, Stratm, SwitchProbe, TeleRouter, are registered trademarks of Cisco Systems, Inc. or its affiliates in the U.S. and certain other countries. All other brands, names, or trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0010R)
- 5. iv About the Author Henry Benjamin, CCIE No.4695, holds three CCIE certifications, having attained Routing and Switching in May 1999, ISP Dial in June 2001, and Communications and Services in May 2002. He has more than 10 years experience with Cisco net- works, including planning, designing, and implementing large IP networks running IGRP, EIGRP, BGP, and OSPF. Recently, Henry has worked for a large IT organi- zation based in Sydney, Australia as a key Network Designer, designing and implementing networks all over Australia and Asia. In the past two years, Henry has been a key member of the CCIE global team based in Sydney, Australia. As a senior and core member of the team, his tasks include writing new laboratory examinations and questions for the coveted CCIE R/S, CCIE Security, and CCIE C/S tracks, as well as the CCIE written Recertifica- tion Examinations. Henry has authored two other titles, “CCNP Practical Studies: Routing” (Cisco Press) and “CCIE R&S Exam Cram.” Henry holds a Bachelor of Aeronautical Engineering degree from Sydney University (1991). About the Contributing Author Gert De Laet, CCIE No. 2657, has both CCIE Security and Routing and Switching certifications. He has more than nine years of experience in internetworking. Gert currently works for the CCIE team at Cisco in Brussels, Belgium, as CCIE Proctor/Content Engineer and Program Manager for EMEA. He also holds an Engineering degree in Electronics. Gert helped write Chapter 9 of this book and acted as a lead technical reviewer for the entire book. About the Technical Reviewers Anand Deveriya, CCIE No.10401, in Security and MCSE, has five years of LAN/WAN and network security experience with Cisco products. Currently, he is the Network Manager at Summerville Senior Living, where he designed and deployed their nationwide Frame Relay-based WAN network with VoIP. Additionally, he monitors the LAN/WAN security, penetration testing, and OS hardening. Prior to that, he was a network engineer with NEC, where he deployed scalable, secure, and redundant network backbone for dotcom and campus environments using Cisco rout- ers, switches, PIX, and VPN products. Charles Resch, CCIE No. 6582, currently works at Nuclio as a Senior Network Engineer, where he installs and config- ures management equipment to monitor customer networks. Among his projects are e-commerce sites with dual Cisco PIX Firewalls, Cisco Content Switch (CSS) load balancers, Intel and SonicWall SSL off-loaders, Cisco switches (HSRP-VLANs), and Cisco Secure Intrusion Detection Systems (CSIDS). Among other jobs, he has worked as a Senior Instructor at Information Technology Institute—Northwestern Business College, and as a Senior Internet Engineer at Globalcom Inc. He has extensive experience with Cisco hardware, Cisco IOS Software, numerous routed and routing protocols, and operating systems. Gert Schauwers, CCIE No. 6924, has CCIE certifications in Security, Routing and Switching, and Communications and Services. He has more than four years of experience in internetworking. He is currently working for the CCIE team at Cisco in Brussels, Belgium, as CCIE Content Engineer. He has an Engineering degree in Electronics.
- 6. v Dedication This book is solely dedicated to two wonderful individuals whom I’ve had the pleasure of meeting on two occasions in my life. Without their inspiration and love for all humanity, I would not be here writing this book. I dedicate this book to His Excellency Monsignor, Claudio Gatti, and Marisa Rossi. I thank God for you. “I am the Mother of the Eucharist. Know Jesus’ word. Love Jesus, the Eucharist.” —Our Lady, Mary, Mother of the Eucharist Questo libro è dedicato esclusivamente a due persone meravigliose che ho avuto il piacere di conoscere e incontrare in due occasioni nella mia vita. Senza la loro ispirazione e il loro amore per tutta l’umanità io non sarei qui a scrivere questo libro. Dedico questo libro a Sua Eccellenza Mons. Claudio Gatti e a Marisa Rossi. “Io sono la madre dell’Eucaristia. Conoscete Gesù parola. Amate Gesù Eucaristia.” —Madonna, Maria, Madre dell’Eucaristia
- 7. vi Acknowledgments I would like to thank the folks at Cisco Press for helping me and introducing me to this challenging project. Brett Bartow, you are an amazing individual. Thank you for your wonderful insight and complete trust in me. Andrew Cupp, or Drew, as you are known to many of us, no bones about it, you are one of a kind; your editing and technical ability really astounded me, and without you, this book would not be the quality product it is now. No book on the market is as good as this one, thanks mate. Thank you for completing all the chapters with your wonderful touches. This book is better because of your input. The team at Cisco Press is an amazing family of hard-working people. It has been a true pleasure to be invited to write this book. Any inspired authors should only ever consider one publisher, Cisco Press. Thanks also to Tammi Ross, Tracy Hughes, and Ginny Bess for all your help. Thank you San Dee Phillips and Patrick Kanouse for your wonderful, final touches that made this book what readers see today. The technical editors, Gert De Laet, Gert Schauwers, Anand Deveriya, and Charles Resch, provided valuable technical expertise and all have shown that they, too, can one day pursue a writing career, as I am sure they will in the near future. Gert De Laet, thank you, especially, for helping me write the security sections of Chapter 9. It was a real pleasure and honor to have you contribute to this book. Gert Schauwers, thank you for all the encouragement you gave me over the last twelve months. Loved that game of golf in San Jose. Gert D. and Gert S., thank you for your true friendship. To finish, I would also like to thank my wife, Sharon, and my one and only son, Simon (the spiderboy). I was always grateful to them both for understanding and knowing when I needed time to complete this project. I treasure my time with my family and my growing little boy who makes me proud to be his Dad. Simon, I love you to the sun, and keep going around forever and ever and watch out for the new Spider Boy movie. I also thank my Dad and Mum for bringing me up with such great examples, and my wife’s parents (Nana and Mate, plus Princess) for their encouragement over the last six months. Uncle Albert, keep making those beautiful donuts and thank you for your encouragement. Thank you to my beautiful sister, Melanie, for her wonderful love throughout my life. This year you become a registered nurse and passed your exams with distinctions. What a wonderful sister you are. I am so proud of you, Mel. Thanks Mello Yello. Massimo Piccinini, my physicist friend in the most beautiful City of the World, Roma, thank you for the friendship and love over the past five years; you are a truly amazing friend (amico). I want to thank my wonderful aunties who gave me wonderful encouragement over all the years they have known me. Thank you, Aunty Lyda and Alice.
- 8. vii Contents at a Glance Foreword xv Introduction xvi Chapter 1 Using This Book to Prepare for the CCIE Security Written Exam 3 Chapter 2 General Networking Topics 11 Chapter 3 Application Protocols 103 Chapter 4 Cisco IOS Specifics and Security 145 Chapter 5 Security Protocols 199 Chapter 6 Operating Systems and Cisco Security Applications 279 Chapter 7 Security Technologies 315 Chapter 8 Network Security Policies, Vulnerabilities, and Protection 361 Chapter 9 CCIE Security Self-Study Lab 391 Appendix A Answers to Quiz Questions 489 Appendix B Study Tips for CCIE Security Examinations 569 Appendix C Sample CCIE Routing and Switching Lab 583 Index 599
- 9. viii Table of Contents Foreword xvi Introduction xvii Conclusion xxi Chapter 1 Using This Book to Prepare for the CCIE Security Written Exam 3 CCIE Security Certification 4 CCIE Security Written Exam Blueprint 4 How to Prepare for the CCIE Security Written Exam Using This Book 7 Chapter 2 General Networking Topics 11 “Do I Know This Already?” Quiz 12 Foundation Topics 21 Networking Basics—The OSI Reference Model 21 Layer 1: The Physical Layer 21 Layer 2: The Data Link Layer 22 Layer 3: The Network Layer 23 Layer 4: The Transport Layer 24 Layer 5: The Session Layer 24 Layer 6: The Presentation Layer 24 Layer 7: The Application Layer 25 TCP/IP and OSI Model Comparison 25 Example of Peer-to-Peer Communication 25 Ethernet Overview 27 Switching and Bridging 28 Bridge Port States 31 FastEther Channel 31 Internet Protocol 33 Variable-Length Subnet Masks 38 Classless Interdomain Routing 39 Transmission Control Protocol 40 TCP Mechanisms 41
- 10. ix TCP Services 45 Address Resolution Protocol (ARP) 45 Reverse ARP 46 Dynamic Host Configuration Protocol 46 Hot Standby Router Protocol 47 Internet Control Message Protocol 52 Telnet 53 File Transfer Protocol and Trivial File Transfer Protocol 53 Routing Protocols 53 Routing Information Protocol 57 EIGRP 62 OSPF 66 Border Gateway Protocol 76 ISDN 79 Basic Rate and Primary Rate Interfaces 80 ISDN Framing and Frame Format 80 ISDN Layer 2 Protocols 80 Cisco IOS ISDN Commands 82 IP Multicast 83 Asynchronous Communications and Access Devices 84 Foundation Summary 87 Requirements for FastEther Channel 89 Q&A 93 Scenario 99 Scenario 2-1: Routing IP on Cisco Routers 99 Scenario Answers 101 Scenario 2-1 Answers: Routing IP on Cisco Routers 101 Chapter 3 Application Protocols 103 “Do I Know This Already?” Quiz 103 Foundation Topics 110 Domain Name System 110 Trivial File Transfer Protocol 113
- 11. x File Transfer Protocol 115 Active FTP 116 Passive FTP 117 Hypertext Transfer Protocol 118 Secure Socket Layer 120 Simple Network Management Protocol 121 SNMP Notifications 122 SNMP Examples 126 Simple Mail Transfer Protocol 127 Network Time Protocol 128 Secure Shell 132 Foundation Summary 134 Q&A 136 Scenario 140 Scenario 3-1: Configuring DNS, TFTP, NTP, and SNMP 140 Scenario Answers 142 Scenario 3-1 Solutions 142 Chapter 4 Cisco IOS Specifics and Security 145 “Do I Know This Already?” Quiz 145 Foundation Topics 150 Cisco Hardware 150 Random-Access Memory (RAM) 151 Nonvolatile RAM (NVRAM) 151 System Flash 151 Central Processing Unit 152 Read-Only Memory 153 Configuration Registers 154 Cisco Interfaces 156 Saving and Loading Files 158 show and debug Commands 159 Router CLI 159 show Commands 159 Debugging Cisco Routers 168
- 12. xi Password Recovery 174 Basic Security on Cisco Routers 179 IP Access Lists 182 Access Lists on Cisco Routers 182 Extended Access Lists 187 Foundation Summary 191 Q&A 193 Scenario 195 Scenario 4-1: Configuring Cisco Routers for Passwords and Access Lists 195 Scenario Answers 197 Chapter 5 Security Protocols 199 “Do I Know This Already?” Quiz 199 Foundation Topics 208 Authentication, Authorization, and Accounting (AAA) 208 Authentication 210 Authorization 210 Accounting 211 Remote Authentication Dial-In User Service (RADIUS) 212 RADIUS Configuration Task List 215 Terminal Access Controller Access Control System Plus (TACACS+) 218 TACACS+ Configuration Task List 220 TACACS+ Versus RADIUS 224 Kerberos 225 Kerberos Configuration Task List 228 Virtual Private Dial-Up Networks (VPDN) 229 VPDN Configuration Task List 232 Encryption Technology Overview 235 Data Encryption Standard (DES) and Triple Data Encryption Standard (3DES) 237 Digital Signature Standard (DSS) 238 Message Digest 5 (MD5) and Secure Hash Algorithm (SHA) 239 Diffie-Hellman 240 IP Security IPSec 242
- 13. xii Internet Key Exchange (IKE) 246 IKE Phase I Messages Types 1-6 247 IKE Phase II Message Types 1-3 248 Cisco IOS IPSec Configuration 252 Certificate Enrollment Protocol (CEP) 259 Foundation Summary 260 Q&A 265 Scenario 271 Scenario 5-1: Configuring Cisco Routers for IPSec 271 Scenario Answers 275 Scenario 5-1 Solutions 275 Chapter 6 Operating Systems and Cisco Security Applications 279 “Do I Know This Already?” Quiz 279 Foundation Topics 284 UNIX 284 UNIX Command Structure 285 UNIX Permissions 288 UNIX File Systems 289 Microsoft NT Systems 290 Browsing and Windows Names Resolution 291 Scaling Issues in Windows NT 292 Login and Permissions 293 Windows NT Users and Groups 294 Windows NT Domain Trust 294 Common Windows DOS Commands 295 Cisco Secure for Windows and UNIX 297 Cisco Secure Policy Manager 299 Cisco Secure Intrusion Detection System and Cisco Secure Scanner 299 NetRanger (Cisco Secure Intrusion Detection System) 300 NetSonar (Cisco Secure Scanner) 302 Cisco Security Wheel 304 Foundation Summary 305
- 14. xiii Q&A 308 Scenarios 311 Scenario 6-1: NT File Permissions 311 Scenario 6-2: UNIX File Permissions 311 Scenario Answers 312 Scenario 6-1 Solution 312 Scenario 6-2 Solution 312 Chapter 7 Security Technologies 315 “Do I Know This Already?” Quiz 315 Foundation Topics 320 Advanced Security Concepts 320 Network Address Translation and Port Address Translation 324 NAT Operation on Cisco Routers 326 Cisco Private Internet Exchange (PIX) 328 Configuring a PIX 332 Cisco PIX Firewall Software Features 342 Cisco IOS Firewall Security Feature Set 344 CBAC Configuration Task List 346 Public Key Infrastructure 348 Virtual Private Networks 349 Foundation Summary 352 Q&A 355 Scenario 358 Scenario 7-1: Configuring a Cisco PIX for NAT 358 Scenario Answer 359 Scenario 7-1 Solution 359
- 15. xiv Chapter 8 Network Security Policies, Vulnerabilities, and Protection 361 “Do I Know This Already?” Quiz 361 Foundation Topics 365 Network Security Policies 365 Standards Bodies and Incident Response Teams 366 Incident Response Teams 367 Internet Newsgroups 368 Vulnerabilities, Attacks, and Common Exploits 369 Intrusion Detection System 372 Protecting Cisco IOS from Intrusion 375 Foundation Summary 381 Q&A 384 Scenario 387 Scenario 8-1: Defining IOS Commands to View DoS Attacks in Real Time 387 Scenario Answer 388 Scenario 8-1 Solution 388 Chapter 9 CCIE Security Self-Study Lab 391 How to Use This Chapter 391 Goal of This Lab 391 CCIE Security Self-Study Lab Part I Goals 392 CCIE Security Self-Study Lab Part II Goals 393 General Lab Guidelines and Setup 393 Communications Server 396 CCIE Security Self-Study Lab Part I: Basic Network Connectivity (4 Hours) 397 Basic Frame Relay Setup 397 Physical Connectivity 403 Catalyst Ethernet Switch Setup I 403 Catalyst Ethernet Switch Setup II 408 IP Host Lookup and Disable DNS 414 PIX Configuration 414 IGP Routing 419 Basic ISDN Configuration 432
- 16. xv DHCP Configuration 438 BGP Routing Configuration 439 CCIE Security Self-Study Lab Part II: Advanced Security Design (4 Hours) 442 IP Access List 442 Prevent Denial-of-Service Attacks 444 Time-Based Access List 446 Dynamic Access List/Lock and Key Feature 448 IOS Firewall Configuration on R5 450 IPSec Configuration 452 Advanced PIX Configuration 458 ACS Configuration 461 Final Configurations 470 Conclusion 486 Appendix A Answers to Quiz Questions 489 Appendix B Study Tips for CCIE Security Examinations 569 Appendix C Sample CCIE Routing and Switching Lab 583 Index 599
- 17. xvi Foreword The CCIE program is designed to help individuals, companies, industries, and countries succeed in the net- worked world by distinguishing the top echelon of internetworking experts. In particular, the CCIE Security Certification is designed to identify network security experts. The first step along the CCIE Security path is for individuals to take a challenging written exam designed to assess their knowledge across a range of technologies. If their scores indicate expert-level knowledge, candidates then proceed to a performance-based CCIE Security Certification Lab Exam. Why Security Certifications? Security is one of the fastest-growing areas in the industry. The expansive development of the Internet, the increase in e-business, and the escalating threat to both public- and private-sector networks have made security and the protection of information a primary concern for all types of organizations. An ever-increasing demand exists for the experts with the knowledge and skills to do it. Therefore, trained network security personnel will be required in the years to come. Why CCIE Security? CCIE Security distinguishes the top level of network security experts. The CCIE Security Certification enables individuals to optimize career growth, opportunity, and compensation by distinguishing themselves as being part of the network security experts of the world. The CCIE Security Certification enables companies to minimize their risk by identifying the highest caliber of security personnel with the training and skills necessary to protect their critical information assets. This book will be a valuable asset to potential CCIE Security candidates. I am positive individuals will gain extensive security network knowledge during their preparation for the CCIE Security written exam using this book. The book’s main focus is providing an in-depth description of the various security features and an understanding of, and ability to navigate, the subtleties, intricacies, and potential pitfalls inherent to net- working security. This book and accompanying CD-ROM contain many tools to strongly supplement your preparation for CCIE Security certification. Good Luck! Gert De Laet Product Manager CCIE Security Cisco Systems, Inc.
- 18. xvii Introduction The Cisco Certified Internet Expert Security Certification is an increasingly popular internetworking certifi- cation and one of the most popular security certifications in the world. Although CCIE certification builds on the foundation you might have established from the Cisco Certified Network Associate (CCNA) and Cisco Certified Network Professional (CCNP) certifications, there is no prerequisite to attempt to gain CCIE certi- fication. However, attaining CCNA and CCNP certifications will help you understand Cisco subjects and testing strategies. This book is designed to help you prepare for the CCIE Security written exam (Exam #350-018). It will also help prepare you for the CCIE Security Recertification exam (Exam #350-009). Cisco released the Security CCIE track in 2001, and its popularity has grown to such an extent that Cisco is investing more heavily in this track than any other current CCIE track. To achieve CCIE Security certification, you must pass a written exam and a one-day lab exam. To qualify for the CCIE Security lab examination, you must first successfully pass the written exam. Both examinations are difficult, and this book is primarily aimed at helping you prepare for the written exam. Chapter 9 includes a CCIE Security self-study lab that helps you with comprehensive preparation for the written exam and gives you an idea of the challenges you will face in the lab exam. Cisco makes achieving CCIE Security certification intentionally difficult. No one book can prepare you for the exam. You should have extensive practical experience and consult many resources. This will give you a comprehensive look at all of the topics covered on the CCIE Security written exam (see Chapter 1). Use this book and the CD-ROM to confidently assess your level of preparedness for all of the topics covered on the exam. The CCIE Security written examination is a two-hour, multiple-choice examination with a surprising amount of Cisco IOS Software configurations and scenario type questions. Some questions require only one answer while other questions require two or more. The CCIE Security written exam is the first step you must take to attain CCIE Security certification. This book provides you with the technical and practical knowledge to prepare for the CCIE Security written exam and enables you to obtain the skills required to fully appreciate what needs to be achieved on your journey towards one of the most sought-after certifications today. Passing the written examination means that you have mastered the networking concepts and fundamental security topics necessary to build a complex, secure, and routable IP network using Cisco routers. This is a great skill and demonstrates to any employer that you are ready for any challenges that might be asked of you. NOTE The CCIE Security written exam is a computer-based exam with multiple-choice questions. The exam can be taken at any VUE testing site (www.VUE.com/cisco) or Prometric testing center (1-800-829-NETS, www.2test.com). The exam is 2 hours long and has 100 questions. Check with VUE or Prometric for the exact length of the exam. The exam is constantly under review, so be sure to check the latest updates from Cisco: www.cisco.com/en/US/learning/le3/le2/le23/le476/learning_certification_type_home.html
- 19. xviii NOTE For more information on how to use this book and preparing for the CCIE Security exam, refer to Chapter 1, “Using This Book to Prepare for the CCIE Security Written Exam,” and Appendix B, “Study Tips for CCIE Security Examinations.” Goals of This Book This book’s primary goal is to ensure that a CCIE Security candidate has all the technical skills and knowl- edge required to pass the written examination. Most Cisco certifications require practical skills and the only way to provide you with those skills is to demonstrate them in a working environment using common Cisco- defined techniques. This book provides you with comprehensive coverage of CCIE Security exam topics, with minimal coverage of nonexam foundation topics. Ultimately, the goal of this book is to get you from where you are today to the point that you can confidently pass the CCIE Security written exam. Therefore, all this book’s features, which are outlined later in this introduction, are geared toward helping you discover the IP routing challenges and security scenarios that are on the exam, helping you discover where you have a knowledge deficiency in these topics, and what you need to know to master those topics. The accompanying CD is an invaluable tool that simulates the real exam and has a pool of over 300 questions. The CD can be used in study mode, which allows you to focus on certain topics and includes links to the electronic version of this book, or exam mode, which allows you to take a timed simulated exam. Organization of this Book Each chapter starts by testing your current knowledge with a “Do I Know this already” quiz. This quiz is aimed at helping you decide whether you need to cover the entire chapter, whether you need to read only parts of the chapter, or if you can skip the chapter. See Chapter 1 and the introduction to each “Do I Know this already” quiz for more details. Each chapter then contains a Foundation Topics section with extensive coverage of the CCIE Security exam topics covered in that chapter. A Foundation Summary section that provides more condensed coverage of the topics and is ideal for review and study follows this. Each chapter ends with Q & A and Scenarios sections to help you assess how well you mastered the topics covered in the chapter. Chapter 1, “Using This Book to Prepare for the CCIE Security Written Exam” Chapter 1 covers details about the CCIE Security exam topics and how to use this book. The CCIE Security written exam blueprint is discussed in this chapter.
- 20. xix Chapter 2, “General Networking Topics” Chapter 2 covers general networking technologies, including an overview of the OSI model, switching con- cepts, and routing protocols. The TCP/IP model is presented and explained with common applications used in today’s IP networks. Routing protocols and sample configurations are presented to ensure that you have a good understanding of how Cisco IOS routes IP datagrams. Concluding this chapter is a discussion of some of today’s most widely used WAN protocols, including PPP, ISDN, and Frame Relay. Keep in mind that the CCIE Security exam covers routing and switching topics as well as security topics. See the exam topics listed in Chapter 1 for more details. Chapter 3, “Application Protocols” Chapter 3 covers the principles of Domain Name System and TFTP file transfers. The most widely used applications such as FTP and HTTP are covered along with some of the more secure methods used to down- load information from the World Wide Web, such as Secure Shell and the Secure Socket Layer protocol. A challenging scenario is included to ensure that you have the IOS skill set to configure DNS, TFTP, NTP, and SNMP. Chapter 4, “Cisco IOS Specifics and Security” Chapter 4 covers the more advanced topics available to Cisco IOS routers. It covers in detail the hardware components of a Cisco router and how to manage Cisco routers. Common Cisco device operation commands are described and examples show how to manage Cisco IOS in today’s large IP networks. Cisco password recovery techniques and basic password security are detailed to ensure you have a solid grasp of Cisco device operation. Coverage of standard and extended access lists and examples conclude this chapter. Chapter 5, “Security Protocols” Chapter 5 focuses on security protocols developed and supported by Cisco Systems and refined in RFCs, namely TACACS+, RADIUS, and Kerberos. Following sample configurations, the chapter covers encryp- tion technologies and their use in today’s vulnerable IP networks. Chapter 6, “Operating Systems and Cisco Security Applications” Chapter 6 covers today’s most widely used operating systems: Windows and UNIX. The applications that run over these platforms are covered in more detail. Cisco Secure and Cisco Policy Manger are discussed. Chapter 7, “Security Technologies” Chapter 7 describes the basic security methods and evolution of the new secure networks, including packet filtering and proxies. The IP address depletion rates with IPv4 have led to NAT/PAT becoming increasingly popular; this chapter covers these topics along with sample IOS configurations. The Cisco PIX is Cisco’s trademark security device, and this chapter teaches you the architecture and configuration of these unique security devices. The IOS feature set and VPNs are covered to conclude this chapter.
- 21. xx Chapter 8, “Network Security Policies, Vulnerabilities, and Protection” Chapter 8 reviews today’s most common Cisco security policies and mechanisms available to the Internet community to combat cyber attacks. The standard security body, CERT/CC, is covered along with descrip- tions of Cisco IOS-based security methods used to ensure that all attacks are reported and acted upon. Cisco Security applications, such as Intrusion Detection System, are covered to lay the fundamental foundations you need to master the topics covered on the CCIE Security written examination. Chapter 9, “CCIE Security Self-Study Lab” Chapter 9 is designed to assist you in your final preparation for CCIE Security exam. Developed by one former (Sydney CCIE lab) and current CCIE proctor (Brussels CCIE lab) from the CCIE team, this chapter contains a sample CCIE security lab with full working solutions to ensure that you are fully prepared for the final hurdle, the CCIE laboratory examination. This lab is intended to challenge your practical application of the knowledge covered in the book, and it should give you a good sense of the areas you need to concentrate your study to prepare for the lab exam. Appendix A, “Answers to Quiz Questions” Appendix A provides the answers to the “Do I Know this Already” and Q & A quiz questions in each chapter. Explanations are included where appropriate. Appendix B, “Study Tips for CCIE Security Examinations” Appendix B describes some of the study tips and preparations steps you should consider before embarking on the long road to CCIE Security certification. Appendix C, “Sample CCIE Routing and Switching Lab” Appendix C is a bonus appendix designed to assist you in your final preparation for the CCIE Routing and Switching lab exam, and help you appreciate the level of difficulty found in any CCIE laboratory examination. CD-ROM The CD-ROM provides you with a sample testing engine that simulates the real examination with over 300 questions that will ensure that you have all the necessary knowledge to pass the first step in your journey. The robust test engine allows you to concentrate your study on particular topics, take full, timed exams, and refer to an electronic version of the text that explains each topic. Take the CD-ROM test and review all the answers so that you are fully prepared for the CCIE Security written exanimation. Also on the CD-ROM are URL links and sample configurations used throughout the book. As a bonus, my first book, CCIE Exam Cram, is also included for those of you studying for the Routing and Switching examination, or who need to brush up on the Routing and Switching portions of the CCIE Security exams. Please enjoy this free bonus.
- 22. xxi Command Syntax Conventions Command syntax in this book conforms to the following conventions: • Commands, keywords, and actual values for arguments are bold. • Arguments (which need to be supplied with an actual value) are in italics. • Optional keywords and arguments are in brackets []. • A choice of mandatory keywords and arguments is in braces {}. Note that these conventions are for syntax only. Conclusion Having many Cisco certifications myself, the joy and success I have achieved has significantly changed my life and that of my family. There are always challenges facing network engineers and, no doubt, becoming a certified Cisco professional meeting those challenges will drive you into acquiring skills you thought you never knew you could master. I sincerely hope you enjoy your time spent with this book; it took over six months and long nights to com- plete to ensure you have the perfect companion through your journey to becoming CCIE certified. When you succeed in attaining your certification, feel free to e-mail me at hbenjamin@optusnet.com.au so I, too, can enjoy your success.
- 24. xxiii
- 26. CHAPTER 1 Using This Book to Prepare for the CCIE Security Written Exam Cisco Systems offers many different varieties and levels of career certifications, including the three current CCIE certification tracks. This book helps prepare you for the written exam (#350-018) for the CCIE Security certification. The CCIE program has existed for almost 10 years. The relative complexity of the CCIE examinations prompted Cisco to introduce associate and professional levels of certification to provide candidates a way to progress through the various levels of certification. Though many of these lower levels of certification have prerequisites to go along with the written exams, CCIE certification does not have any prerequisites. To become a CCIE, you need to pass two exams: a written exam and a one-day lab exam. NOTE For details on Cisco career certifications, visit www.cisco.com/en/US/learning/le3/ learning_career_certifications_and_learning_paths_home.html. By introducing these lower-level certifications, Cisco has maintained the complexity of the CCIE examinations. Passing any CCIE examination by reading only one book is still difficult. Being adequately prepared requires plenty of on-the-job experience and intense study. This book helps you prepare for the CCIE Security written exam by making you aware of the material you will be tested on, by helping you identify where you have knowledge gaps, and by providing you with practice and study tools, such as the sample exam on the CD-ROM. NOTE Although this book’s primary goal is to help you prepare for the CCIE Security written exam, you will find some supplemental material that can help you begin to prepare for the CCIE Security Lab exam, too. For example, Chapter 9, “CCIE Security Self-Study Lab,” includes a sample CCIE Security Lab written by qualified CCIE proctors. The remainder of this chapter covers how you can use this book to prepare for the CCIE Security written exam. The next section covers some basic information about the exam, including a listing of the exam topics.
- 27. 4 Chapter 1: Using This Book to Prepare for the CCIE Security Written Exam CCIE Security Certification At this stage, you have decided to pursue CCIE Security certification, which requires you to pass a two-hour, 100-question, written qualification exam (#350-018) and a one-day lab. NOTE In addition to the CCIE Security certification, there are CCIE certifications for Routing and Switching and for Communications and Services. For information on these other CCIE certifications, see www.cisco.com/en/US/learning/le3/le2/le23/learning_certification_ level_home.html. After you successfully complete the written examination, you can take the one-day lab. You must wait at least one month after passing the written test before sitting for the lab exam. The written test is designed to be difficult so that potential CCIE candidates are fully prepared and aware of the difficulty level of the lab. The Cisco CCIE certification website at www.cisco.com/en/US/learning/le3/le2/le23/ learning_certification_level_home.html contains further details about all the CCIE certification paths and exams, and information on possible new tracks when Cisco decides to release them to the public. CCIE Security Written Exam Blueprint This section includes the entire CCIE Security written exam blueprint (exam objectives) from the Cisco website and indicates the corresponding chapters in this book that cover those objectives. Table 1-1 lists the CCIE Security written exam blueprint and where you can find the material covered in this book. As you can see, the blueprint places the objectives into eight categories. Table 1-1 CCIE Security Written Exam Blueprint (Exam Objectives) Chapter Topic Covering the Number Objective Objective Security Protocols 1 Remote Authentication Dial-In User Service (RADIUS) Chapter 5 2 Terminal Access Controller Access Control System Plus (TACACS+) Chapter 5 3 Kerberos Chapter 5
- 28. CCIE Security Written Exam Blueprint 5 Table 1-1 CCIE Security Written Exam Blueprint (Exam Objectives) (Continued) Chapter Topic Covering the Number Objective Objective 4 Virtual Private Dialup Networks (VPDN/Virtual Profiles) Chapter 5 5 Data Encryption Standard (DES) Chapter 5 6 Triple DES (DES3) Chapter 5 7 IP Secure (IPSec) Chapter 5 8 Internet Key Exchange (IKE) Chapter 5 9 Certificate Enrollment Protocol (CEP) Chapter 5 10 Point-to-Point Tunneling Protocol (PPTP) Chapter 5 11 Layer 2 Tunneling Protocol (L2TP) Chapter 5 Operating Systems 12 UNIX Chapter 6 13 Windows (NT/95/98/2000) Chapter 6 Application Protocols 14 Domain Name System (DNS) Chapter 3 15 Trivial File Transfer Protocol (TFTP) Chapter 3 16 File Transfer Protocol (FTP) Chapter 3 17 Hypertext Transfer Protocol (HTTP) Chapter 3 18 Secure Socket Layer (SSL) Chapter 3 19 Simple Mail Transfer Protocol (SMTP) Chapter 3 20 Network Time Protocol (NTP) Chapter 3 21 Secure Shell (SSH) Chapter 3 22 Lightweight Directory Access Protocol (LDAP) Chapter 3 23 Active Directory Chapter 3 General Networking 24 Networking Basics Chapter 2 25 TCP/IP Chapter 2 26 Switching and Bridging (including: VLANs, Spanning Tree, etc.) Chapter 2 27 Routed Protocols Chapter 2 28 Routing Protocols (including: RIP, EIGRP, OSPF, BGP) Chapter 2 continues
- 29. 6 Chapter 1: Using This Book to Prepare for the CCIE Security Written Exam Table 1-1 CCIE Security Written Exam Blueprint (Exam Objectives) (Continued) Chapter Topic Covering the Number Objective Objective General Networking (Continued) 29 Point-to-Point Protocol (PPP) Chapter 2 30 IP Multicast Chapter 2 31 Integrated Services Digital Network (ISDN) Chapter 2 32 Async Chapter 2 33 Access Devices (for example, Cisco AS 5300 series) Chapter 2 Security Technologies 34 Concepts Chapter 7 35 Packet filtering Chapter 7 36 Proxies Chapter 7 37 Port Address Translation (PAT) Chapter 7 38 Network Address Translation (NAT) Chapter 7 39 Firewalls Chapter 7 40 Active Audit Chapter 7 41 Content filters Chapter 7 42 Public Key Infrastructure (PKI) Chapter 7 43 Authentication Technologies Chapter 7 44 Virtual private networks (VPN) Chapter 7 Cisco Security Applications 45 Cisco Secure UNIX Chapter 6 46 Cisco Secure NT Chapter 6 47 Cisco Secure PIX Firewall Chapter 7 48 Cisco Secure Policy Manager (formerly Cisco Security Manager) Chapter 6 49 Cisco Secure Intrusion Detection System (formerly NetRanger) Chapter 6 50 Cisco Secure Scanner (formerly NetSonar) Chapter 6 51 IOS Firewall Feature Set Chapter 7 Security General 52 Policies Chapter 8 53 Standards bodies Chapter 8
- 30. How to Prepare for the CCIE Security Written Exam Using This Book 7 Table 1-1 CCIE Security Written Exam Blueprint (Exam Objectives) (Continued) Chapter Topic Covering the Number Objective Objective 54 Incident response teams Chapter 8 55 Vulnerability Discussions Chapter 8 56 Attacks and common exploits Chapter 8 57 Intrusion detection Chapter 8 Cisco General 58 IOS specifics Chapter 4 How to Prepare for the CCIE Security Written Exam Using This Book This book provides several tools designed to prepare you for the CCIE Security written exam. Each chapter helps you evaluate your comprehension of the exam objectives from the blueprint (see Table 1-1). In addition, this book includes a CD-ROM with a bank of over 300 sample exam questions you can use to take practice exams. The CD-ROM contains a good mixture of easy and difficult questions to mimic the content and questions asked in the real examination. NOTE For more information about the CCIE Security exams and for general tips on how to prepare for the exams beyond just using this book, see Appendix B, “Study Tips for CCIE Security Examinations.” The chapters open by identifying the exam objectives covered in that chapter. You can begin by taking the “Do I Know This Already?” Quiz to immediately evaluate how familiar you are with a subject. Then, use the quiz instructions in each chapter to decide how much you need to study the subject. If you need to learn a lot, start with the “Foundation Topics” section, which goes into detail about the objectives covered in that chapter. If your quiz results demonstrate that you already have a strong grasp of the subject, you can skip to the “Foundation Summary,” “Q & A,” and “Scenarios” sections at the end of the chapter. Each of these elements includes detailed instructions on how to best use it to prepare for the exam. This book covers all the objectives in the CCIE Security written exam blueprint, but no one book can teach you everything you need to know for a CCIE exam. Although you can use this book to identify and fill in knowledge gaps, you might encounter areas where you feel less
- 31. 8 Chapter 1: Using This Book to Prepare for the CCIE Security Written Exam prepared than others. Consider supplementing your learning in these areas with practical experience, specific books on the subject, or on CCO (Cisco Connection Online). In addition to the chapters in this book, the accompanying CD-ROM provides tools that can help you prepare for the exam. The CD-ROM includes over 300 sample questions that you can explore in a few modes. You can work through the questions in study mode. Study mode allows you to link to an electronic version of the book when you want more information on the partic- ular topic covered in the question. In study mode, you can choose the topics and number of questions you want to work through. Practice exam mode allows you to take a simulated exam with a time limit and randomly selected questions. At the end of the exam, you receive a score and a categorical breakdown of your performance. Use these results to identify areas of strengths and weaknesses, so you can use this book and other resources to fill in any knowledge gaps. Using this book is one of the best steps you can take toward achieving the most sought after certification in the IT industry. You need to rely on your extensive experience to pass the exam, but this book can make your preparation focused and efficient. Do not give up, and keep studying until you become certified. When you do pass, please e-mail me at hbenjamin@optushome.com.au so that I can hear of your achievement.
- 33. Exam Topics in This Chapter 24 Networking Basics 25 TCP/IP 26 Switching and Bridging (Including VLANs, Spanning Tree, and more) 27 Routed Protocols 28 Routing Protocols (Including RIP, EIGRP, OSPF, and BGP) 29 Point-to-Point Protocol (PPP) 30 IP Multicast 31 Integrated Services Digital Network (ISDN) 32 Async 33 Access Devices (For Example, Cisco AS 5300 Series)
- 34. CHAPTER 2 General Networking Topics This chapter covers general networking concepts listed in the CCIE Security blueprint for the written exam. The CCIE blueprint lists some example topics that define general networking, including switching, TCP/IP, routed and routing protocols, PPP, ISDN, and asynchronous communications. The CCIE Security written exam contains approximately 50 percent security questions and approximately 50 percent general networking questions. This chapter prepares you for the general networking questions. Although the CCIE Security written exam blueprint lists some specific networking topics, it does not, for example, mention Frame Relay, which might appear on the exam. This chapter covers many of the listed and a few of the unlisted general networking topics. Although these topics are not extensively defined in the blueprint, the CCIE Security written exam might include topics taken from the CCIE Routing and Switching written exam blueprint. This chapter endeavors to cover all bases and provide quality test examples to ensure that you are well prepared to tackle the general networking questions you encounter in the examination. This chapter covers the following topics: • Networking basics—The OSI model, concepts, and functions. Topics include the seven layers of the OSI model and common examples (TCP/IP). • Switching and bridging—The process today’s networks use to switch packets and traditional bridging methods. Virtual LANs, spanning tree, and Ethernet Channel are discussed. • Routing IP—The most widely used routed protocol in today’s Internet, IP, and the routing protocols available on Cisco routers, such as RIP, EIGRP, OSPF, and BGP. IOS commands and configuration examples demonstrate the power of routing IP on Cisco routers. • PPP, ISDN, Frame Relay, IP Multicast, and Async—Two of the most widely used dialup protocols are PPP and ISDN. Frame Relay is covered briefly to ensure that you have a good understanding of the common terminology used in today’s networks. IP multicast and async protocols are also covered.
- 35. 12 Chapter 2: General Networking Topics “Do I Know This Already?” Quiz This assessment quiz will help you determine how to spend your limited study time. If you can answer most or all these questions, you might want to skim the “Foundation Topics” section and return to it later as necessary. Review the “Foundation Summary” section and answer the questions at the end of the chapter to ensure that you have a strong grasp of the material covered. If you already intend to read the entire chapter, you do not necessarily need to answer these questions now. If you find these assessment questions difficult, read through the entire “Foun- dation Topics” section and review it until you feel comfortable with your ability to answer all these and the “Q & A” questions at the end of the chapter. Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.” 1 Which layer of the OSI model is responsible for converting frames into bits and bits into frames? a. Physical b. Network c. Transport d. LLC sublayer e. Data Link 2 Routing occurs at what layer of the OSI model? a. Physical b. Network c. Transport d. LLC sublayer e. Data link 3 Bridging occurs at what layer of the OSI model? a. Physical b. Network c. Transport d. Data link 4 Which of the following is not part of the OSI model? a. Network layer b. Physical layer c. Operational layer d. Application layer
- 36. “Do I Know This Already?” Quiz 13 5 IP operates at what layer of the OSI model? a. Layer 1 b. Layer 2 c. Layer 3 d. Layer 4 e. Layer 5 f. Layer 6 g. Layer 7 6 On which layer of the OSI model is data commonly referred to as segments? a. Layer 4 b. Layer 3 c. Layer 2 d. Layer 1 7 On which layer of the OSI model is data commonly referred to as packets? a. Layer 1 b. Layer 2 c. Layer 4 d. Layer 3 8 Which layer of the OSI model transmits raw bits? a. Layer 1 b. Layer 2 c. Layer 3 d. Layer 4 9 Which of the following protocols is not routable? a. IP b. IPX c. NetBEUI d. NetBIOS
- 37. 14 Chapter 2: General Networking Topics 10 Which of the following is not a required step to enable FastEther Channel (FEC)? a. Ensure that all ports share the same speed at 10 Mbps. b. Ensure that all ports share the same parameter such as speed. c. Ensure that all ports operate at 100 Mbps. d. Only eight ports can be bundled into a logical link or trunk. 11 How is FastEther Channel best defined? a. A bundle of 10-Mbps ports on a switch b. Another name for half duplex 100 Mbps c. Not available on Cisco Catalyst switches d. The ability to bundle 100 Mbps ports into a logical link e. Only supported with Gigabit ports 12 On what OSI layer does bridging occur? a. Layer 1 b. Layer 2 c. Layer 3 d. Both Layer 1 and 2 13 In spanning tree, what is a BPDU? a. A break protocol data unit b. A routable frame c. A bridge protocol data unit d. A frame sent out by end stations 14 An incoming frame on a Layer 2 switch is received on port 10/1 on a Catalyst 5000. If the destination address is known through port 10/2, what happens? a. The frame is discarded. b. The frame is sent via port 10/2. c. The frame is broadcast to all ports on the switch. d. The frame is sent back via 10/1. e. None of the above.
- 38. “Do I Know This Already?” Quiz 15 15 Which of the following are the four possible states of spanning tree? a. Listening, learning, blocking, broadcasting b. Listening, learning, blocking, connecting c. Discovering, learning, blocking, connecting d. Listening, learning, blocking, forwarding 16 How many bits make up an IP address? a. 64 bits b. 48 bits c. 32 bits d. 24 bits e. 8 bits 17 Identify the broadcast address for the subnet 131.108.1.0/24. a. 131.108.1.1 b. 131.108.1.254 c. 131.108.1.255 d. 131.108.1.2 e. More data required 18 Convert the following address to binary: 131.1.1.1/24 a. 10000011.1.1.1 b. 10000011.00000010.1.1 c. 10000011.1.1.01010101 d. 10000011.1.1.11111111
- 39. 16 Chapter 2: General Networking Topics 19 How many subnets are possible in VLSM if the Class C address 131.108.255.0 is used with the subnet mask 255.255.255.252 in the fourth octet field? a. None b. 100 c. 255 d. 254 e. 253 f. 252 g. 64 h. 62 20 How many hosts are available when a /26 subnet mask is used? a. 254 b. 62 c. 64 d. 126 21 How many hosts are available in a Class C or /24 network? a. 255 b. 254 c. 253 d. 0 e. More data required 22 You require an IP network to support at most 62 hosts. What subnet mask will accomplish this requirement? a. 255.255.255.255 b. 255.255.255.252 c. 255.255.255.224 d. 255.255.255.192 e. 255.255.255.240
- 40. “Do I Know This Already?” Quiz 17 23 Which of the following are multicast addresses? (Choose all that apply.) a. 224.0.0.5 b. 224.0.0.6 c. 221.0.0.5 d. 192.1.1.1 e. 131.108.1.1 24 Which of the following routing protocols does not support VLSM? a. RIPv1 b. RIPv2 c. OSPF d. EIGRP e. BGP 25 What is the source TCP port number when a Telnet session is created by a PC to a Cisco router? a. 23 b. Not a known variable c. 21 d. 20 e. 69 26 What best describes the ARP process? a. DNS resolution b. Mapping an IP address to a MAC address c. Mapping a next-hop address to outbound interface on a Cisco router d. Both a and b 27 If two Cisco routers are configured for HSRP and one router has a default priority of 100 and the other 99, which router assumes the role of active router? a. The default priority cannot be 100. b. The router with a higher priority. c. The router with the lowest priority. d. Neither router because Cisco routers do not support HSRP; only clients do.
- 41. 18 Chapter 2: General Networking Topics 28 A Cisco router has the following route table: R1#show ip route 131.108.0.0/16 is variably subnetted, 17 subnets, 2 masks C 131.108.255.0/24 is directly connected, Serial0/0 C 131.108.250.0/24 is directly connected, Serial0/1 O 131.108.254.0/24 [110/391] via 131.108.255.6, 03:33:03, Serial0/1 [110/391] via 131.108.255.2, 03:33:03, Serial0/0 R 131.108.254.0/24 [120/1] via 131.108.255.6, 03:33:03, Serial0/1 [120/1] via 131.108.255.2, 03:33:03, Serial0/ What is the preferred path to 131.108.254.0/24? (Choose the best two answers.) a. Via Serial 0/0 b. Via Serial 0/1 c. None d. To null0 29 IP RIP runs over what TCP port number? a. 23 b. 21 c. 69 d. 520 e. None of the above 30 IP RIP runs over what UDP port number? a. 23 b. 21 c. 69 d. 520 31 An OSPF virtual link should . a. Never be used b. Allow nonpartitioned areas access to the backbone c. Allow partitioned areas access to the backbone d. Not be used in OSPF, but in ISDN
- 42. “Do I Know This Already?” Quiz 19 32 What is the BGP version most widely used today? a. 1 b. 2 c. 3 d. 4 e. 5 f. 6 33 What is the destination port number used in a Telnet session? a. 23 b. 69 c. 21 d. 161 34 In what fields does the IP checksum calculate the checksum value? a. Data only b. Header and data c. Header only d. Not used in an IP packet 35 The TCP header checksum ensures integrity of what data in the TCP segment? a. The data only. b. The header only. c. The data and header. d. There are no TCP header checksums; IP covers the calculation. 36 ISDN BRI channels are made up of what? a. 1 × 64 kbps channel and one D channel at 64 kbps b. 2 × 64 kbps channels and one D channel at 64 kbps c. 2 × 64 kbps channels and one D channel at 16 kbps d. 32 × 64 kbps channels and one D channel at 16 kbps
- 43. 20 Chapter 2: General Networking Topics 37 What services can ISDN carry? a. Data only b. Data and voice only c. Voice and video d. Data, voice, and video 38 Place the following steps in the correct order for PPP callback, as specified in RFC 1570. 1. A PC user (client) connects to the Cisco access server. 2. The Cisco IOS Software validates callback rules for this user/line and disconnects the caller for callback. 3. PPP authentication is performed. 4. Callback process is negotiated in the PPP link control protocol (LCP) phase. 5. The Cisco Access Server dials the client. a. 1, 2, 3, 4, 5 b. 1, 3, 2, 5, 4 c. 1, 4, 5, 3, 2 d. 5, 4, 3, 2, 1 39 What hardware port is typically designed to connect a Cisco router for modem access? a. The console port b. The vty lines c. The auxiliary port d. The power switch e. The Ethernet interface 40 The AS5300 series router can support which of the following incoming connections? a. Voice b. Dialup users via PSTN c. ISDN d. All the above
- 44. Networking Basics—The OSI Reference Model 21 Foundation Topics Networking Basics—The OSI Reference Model This section covers the Open Systems Interconnection (OSI) seven layer model theory and common examples. CCIE candidates must fully understand and appreciate the model because almost every routed protocol in use today is based on the architecture of the seven layer model. The OSI model was developed by a standards body called the International Organization for Standardization (ISO) to provide software developers a standard architecture to develop proto- cols (such as IP). For example, the OSI model allows a PC to communicate with a UNIX device. NOTE ISO developed the OSI model in 1984. Layers 1 and 2 are implemented in hardware and Layers 3 through 7 are typically implemented in software. Table 2-1 displays the seven layers of the OSI model. Table 2-1 The OSI Seven Layer Model Layer Name Layer Number Application Layer 7 Presentation Layer 6 Session Layer 5 Transport Layer 4 Network Layer 3 Data Link Layer 2 Physical Layer 1 The following sections cover each layer and provide protocol examples for each. Layer 1: The Physical Layer The physical layer consists of standards that describe bit ordering, bit transmission rates, connector types, and electrical and other specifications. Information at Layer 1 is transmitted in
- 45. 22 Chapter 2: General Networking Topics binary (1s and 0s). For example, the letter A is transmitted as 00001010. Examples of physical layer standards include the following: • RS-232 • V.24 • V.35 • RJ-45 • RJ-12 Layer 2: The Data Link Layer The data link layer focuses on getting data reliably across any particular kind of link. Flow control and error notifications are also functions of the data link layer. The data link layer applies to all access methods, whether they are LAN or WAN methods. Information being processed at this layer is commonly known as frames. The IEEE further complicated matters by subdividing the data link layer into to sublayers: the Logical Link Control (LLC) sublayer and the MAC sublayer. Figure 2-1 displays the IEEE definition compared to the ISO definition. Figure 2-1 IEEE Sublayers Versus ISO Definitions Upper Layers IEEE 802 Definition ISO Standard Logical Link Control, LLC Data Link Layer MAC Sublayer Physical Medium (Layer 1) The LLC sublayer manages and ensures communication between end devices, and the Mac sublayer manages protocol access to the physical layer.
- 46. Networking Basics—The OSI Reference Model 23 Examples of data link frame types include the following: • ISDN • SDLC • HDLC • PPP • Frame Relay • Ethernet Version II • Spanning tree protocol • NetBEUI Layer 3: The Network Layer The network layer determines the best path to a destination. Device addressing, packet fragmentation, and routing all occur at the network layer. Information being processed at this layer is commonly known as packets. Examples of network layer protocols include the following: • Internet Protocol (IP) • Open Shortest Path First (OSPF) • Cisco’s EIGRP routing protocol Routing protocols (OSPF, EIGRP, and BGP, for example) provide the information required to determine the topology of the internetwork and the best path to a remote destination. A routed protocol is one that is transported by a routing protocol (such as RIP). For example, IP is a routed protocol that can be advertised by a number of routing algorithms, such as RIP, OSPF, and BGP. NOTE Connection-oriented and connectionless protocols are commonly used terms to describe Layer 3 and 4 (lower layers of the OSI model) protocols, such as IP or TCP. A connection-oriented protocol, such as TCP, ensures delivery of all information, whereas a connectionless protocol, such as IP, only packages the data and sends it without guaranteeing delivery. Connection-oriented protocols exchange control information (also called Handshake) before transmitting data. A telephone call can be considered a connection-oriented service because the call is established before conversation can take place, much the same way that TCP sets up a data connection before data is sent. FTP is another example of a connection-oriented protocol. IP is an example of connectionless service.
- 47. 24 Chapter 2: General Networking Topics Layer 4: The Transport Layer The transport layer is responsible for segmenting upper-layer applications and establishing end- to-end connections between devices. Other transport layer functions include providing data reliability and error-free delivery mechanisms. Information being processed at this layer is commonly known as segments. Examples of transport layer protocols include the following: • Transmission Control Protocol (TCP) • Real-time transport protocol (RTP) • User Datagram Protocol (UDP) Layer 5: The Session Layer The session layer performs several major functions, including managing sessions between devices and establishing and maintaining sessions. Examples of session layer protocols include the following: • Database SQL • NetBIOS Name Queries • H.323 (Supports video as well; it is the packet switch voice standard) • Real Time Control Protocol Layer 6: The Presentation Layer The presentation layer handles data formats and code formatting. The layer’s functions are normally transparent to the end user because this layer takes care of code formats and presents them to the application layer (Layer 7), where the end user can examine the data. Examples of presentation layer protocols include the following: • GIF • JPEG • ASCII • MPEG • TIFF • MIDI • HTML
- 48. Networking Basics—The OSI Reference Model 25 Layer 7: The Application Layer The application layer is closest to the end user, which means that the application will be accessed by the end user. This layer’s major function is to provide services to end users. Examples of application layer services include the following: • File Transfer Protocol (FTP) • Telnet • Ping • Trace route • SMTP • Mail clients TCP/IP and OSI Model Comparison TCP/IP is the most widely used networking protocol and is often compared to the industry- defined OSI model. Figure 2-2 displays the TCP/IP model in relation to the OSI model and where the protocol suite of TCP/IP lines up with the ISO standard. This comparison is provided to demonstrate that TCP/IP does not exactly conform to the OSI model. For example, the TCP/IP model has no Layer 5 or 6. Figure 2-2 OSI and TCP/IP Models OSI Model TCP/IP Model Application Presentation Applications such as Telnet, FTP. and ping Session Transport TCP UDP Network IP Data Link Network Interface Physical Example of Peer-to-Peer Communication Each layer of the OSI or TCP model has its own functions and interacts with the layer above and below it. Furthermore, the communication between each layer’s end devices also establishes
- 49. 26 Chapter 2: General Networking Topics peer-to-peer communication; this means that each layer of the OSI model communicates with the corresponding peer. Consider the normal communication that occurs between two IP hosts over a wide-area network (WAN) running Frame Relay, as displayed in Figure 2-3. Figure 2-3 Peer-to-Peer Communication Example Data Received by Application Host A Host B Application Data (Layer 7) Application Data (Layer 7) Data Peer-to-Peer Communication Data Layer 4 Peer-to-peer Layer 4 TCP (TCP) communication (TCP) TCP Data Data header header Layer 3 Layer 3 IP TCP IP TCP Data Data header header header header Layer 2 Layer 2 802.3 IP TCP 802.3 IP TCP Data CRC Data CRC header header header header header header 0101011000.......... 0101011000.......... (Binary Transmission) (Binary Transmission) Router A Frame Router B Relay Frame IP TCP Data CRC Relay Header Header The data from one (Host A) is encapsulated inside a TCP header and passed down to Layer 3 (the IP layer) for address configuration, where an IP header is also added. Information included here is the source IP address and destination address. Layer 3 (the network layer) passes the data to the local router acting as the gateway via the Ethernet connection in raw binary. Router A strips the 802.3 header and encapsulates the IP, TCP, and data in a Frame Relay packet for delivery over the WAN. A CRC is added here to ensure the packet is not corrupted over
- 50. Ethernet Overview 27 the WAN. Frame Relay is connectionless so, if an error occurs, it’s up the to upper layers to retransmit; Frame Relay will not retransmit the packet. Similarly, HDLC (Layer 2 protocol) is connectionless and depends on upper layers to resubmit damaged data packets. PPP (connection-oriented), on the other hand, resubmits packets damaged in transmission over the WAN. Router B receives the Layer 2 frames and strips the Frame Relay header/CRC and encapsulates the IP, TCP, and data frame back into an 802.2 header (with its own CRC; Ethernet checks only for errors and cannot repair them; once more, upper layers, such as TCP, ensure data delivery) for binary transmission across the Ethernet to Host B. The data is passed up the layers through IP, TCP, and finally to the application, where the application layer reads and acts upon the data. The good news for security candidates is that Token Ring and legacy technologies are not covered in the written exam, so this chapter concentrates only on Ethernet switching. Before covering switching, the next section summarizes the evolution of Ethernet so that you are aware of the standards that have developed since Xerox first introduced Ethernet. Ethernet Overview Ethernet networks are based on a development made by Xerox, Digital, and Intel. The two versions of Ethernet are commonly referred to as Ethernet I and Ethernet II (or version 2). Ethernet uses Carrier Sense Multiple Access Collision Detection (CSMA/CD) to transmit frames on the wire. In an Ethernet environment, all hosts can transmit as long as no other devices are transmitting. CSMA/CD is used to detect and warn other devices of any collisions, and colliding stations will use a back off algorithm and wait a random amount of time before trying again. Colliding devices send a jam signal to advise all stations that a collision has occurred. When a jam signal is sent (a jam signal is detected by all devices because the voltage is that of the combined colliding devices), all stations also stop transmitting. A device will attempt to transmit up to 16 times before a user is notified of the collisions; typically, an application error will inform the user that data could not be delivered. Microsoft’s famous words are “Network is busy.” NOTE The only time CSMA/CD is not used is in full-duplex connection because collisions are not possible when one pair of UTP is used to transmit and receive data. In other words, devices connected in full-duplex mode can send and receive data at the same time without the possibility of collision. Table 2-2 lists some of the common Ethernet media specifications and the characteristics of each.
- 51. 28 Chapter 2: General Networking Topics Table 2-2 Ethernet Media Formats Media Type Characteristics 10Base5 Maximum length: 500 m Maximum stations: 1024 Speed is 10 Mbps Minimum distance between devices is 2.5 m 10Base2 Maximum length: 185 m, using RG58 cable types and T connectors on all end stations Minimum distance between devices is 0.5 m Maximum devices per 185-m segment is 30 stations Speed is 10 Mbps 10BaseT Based on UTP cabling Up to 100 m, better category cables longer One device per cable. Typically, only one device per segment with hubs or switches connecting all devices together Speed is 10 Mbps Physical topology star, logical topology bus 100BaseT Same characteristics as 10BaseT but operates faster, at 100 Mbps Can be fibre, as well (100BaseFx); defined in IEEE 802.3U Physical topology star, logical topology bus 1000 GE Gigabit Ethernet operating at 1000 Mbps Can run over fibre or UTP; frame formats and CSMA/CD identical to Ethernet standards Physical topology star, logical topology bus * The word BASE refers to Baseband signaling, which uses a single channel, as opposed to broadband, which uses multiple frequency channels. Switching and Bridging This sections covers Layer 2 devices that are used to bridge or switch frames using common techniques to improve network utilization, such as VLANs. The terms switch and bridge are used to mean the same technology. Switching, or bridging, is defined as a process of taking an incoming frame from one interface and delivering it through another interface. Source stations are discovered and placed in a switch address table (called content-addressable memory [CAM] table in Cisco terms). Routers
- 52. Ethernet Overview 29 use Layer 3 switching to route a packet, and Layer 2 switches use Layer 2 switching to forward frames. Switches build CAM tables when activity is noted on switch ports. Example 2-1 displays a sample CAM table on a Cisco Catalyst 5000 switch. Example 2-1 CAM Table or Bridge Table CAT5513 (enable) show cam ? Usage: show cam [count] <dynamic|static|permanent|system> [vlan] show cam <dynamic|static|permanent|system> <mod_num/port_num> show cam <mac_addr> [vlan] show cam agingtime show cam mlsrp <ip_addr> [vlan] CAT5513 (enable) show cam dynamic * = Static Entry. + = Permanent Entry. # = System Entry. R = Router Entry. X = P ort Security Entry VLAN Dest MAC/Route Des Destination Ports or VCs / [Protocol Type] ---- ------------------ ---------------------------------------------------- 36 00-10-7b-54-37-c6 8/13 [ALL] 35 00-09-43-3b-ac-20 8/5 [ALL] 101 00-01-02-00-4a-ff 1/1 [ALL] 1 00-01-02-00-4a-ff 1/1 [ALL] 102 00-03-e3-5e-ac-81 1/1 [ALL] 101 00-00-0c-92-0c-af 1/1 [ALL] 102 00-03-e3-53-7f-81 1/1 [ALL] 102 00-03-e3-5e-ae-c1 1/1 [ALL] 37 00-03-e3-63-55-80 8/9 [ALL] 102 00-03-e3-5e-a9-01 1/1 [ALL] Example 2-1 displays a CAM table on a Catalyst switch with the CatOS command show cam dynamic. You can use other CatOS commands to view specific ports (show cam dynamic 8/13 would show only devices discovered on port 8/13). Example 2-1 displays that the MAC address 01-10-7b-54-37-c6 is located via the port 8/13. A Cisco switch populates the CAM tables as new devices send frames, so a switch bases all bridging decisions on source MAC address. When a device first sends a frame to a connected port on a switch, the switch adds the incoming source address to the CAM table. Any broadcasts received because the switch has no CAM entry are sent out all ports except the port the frame was received on. The switch then adds the source MAC address on the source port. Frames that are received as broadcasts are sent out all ports active in spanning tree.
- 53. 30 Chapter 2: General Networking Topics NOTE Transparent bridges can operate in two traditional modes. Cut through switching occurs when, after the destination MAC address is received, the switch immediately forwards the frame to the outgoing port. If a switch in cut through mode encounters a large number of frames with CRCs, the switch will drop down to store and forward mode. This technique is known as adaptive cut-through. Store and forward switching occurs when the entire frame is received before forwarding the frame. The CRC is checked to ensure that frames containing errors or CRCs are not forwarded. Cut-through switching is faster but the switch could potentially forward frames with errors because the CRC is not checked. The default mode is typically store and forward on Cisco switches. Routers can also be configured to bridge packets. The most common form of switch is adaptive cut-through. Spanning tree is a Layer 2 protocol used to ensure a loop-free topology. A layer 2 loop is devastating to a network, as a frame will circulate the entire broadcast domain until all the switches eventually run out of memory because of the intensive broadcast storm that occurs. Broadcasts must be forwarded to all ports except the source port. NOTE A broadcast domain is defined as a group of all devices that receive broadcast frames originating from any device within the group. Broadcast domains are typically bound by routers because routers do not forward broadcast frames. Switches, on the other hand, must forward all broad- casts out all ports except the port the frame was received from. Spanning tree is used when there are multiple LAN segments or virtual LANs (VLANs). A VLAN is a defined group of devices on one or more LANs that are configured (using manage- ment software, such as Catalyst switch code or CatOS) to communicate as if they were attached to the same wire when, in fact, they are located on a number of different LAN segments. VLANs are based on logical instead of physical connections and must be connected to a Layer 3 device, such as a router, to allow communication between all segments. To create a VLAN on a Catalyst switch, the CatOS command is set vlan vlan id. The vlan id is a number between 2 and 1005. By default, Cisco switches have vlan 1 already configured and cannot be removed for manage- ment purposes because protocols such as CDP and spanning tree will be active. You can disable CDP and spanning tree (not recommended in large switches networks). Spanning tree is on by default on all Catalyst switches, and before data can be received or sent on any given port, Spanning tree protocol (STP) will go through a root bridge election phase. A root bridge election takes into account the bridge priority (value between 0 and 65535, default is 32768, and lower is better). If that value is equal in a segment with multiple bridges, the lowest MAC address associated with the bridge is elected as the root bridge.
- 54. Ethernet Overview 31 NOTE Bridges communicate using frames called Bridge Protocol Data Units (BPDUs). BPDUs are sent out all ports not in a blocking state. A root bridge has all ports in a forwarding state. To ensure a loop-free topology, nonroot bridges block any paths to the root that are not required. BPDUs use the destination MAC address 01-08-C2-00-00-00 in Ethernet environments. Bridge Port States Every bridge and associated port is in one of the following spanning tree states: • Disabled—The port is not participating in spanning tree and is not active. • Listening—The port has received data from the interface and will listen for frames. In this state, the bridge receives only data and does not forward any frames to the interface or to other ports. • Learning—In this state, the bridge still discards incoming frames. The source address associated with the port is added to the CAM table. BPDUs are sent and received. • Forwarding—The port is fully operational; frames are sent and received. • Blocking—The port has been through the learning and listening states, and because this particular port is a dual path to the root bridge, the port is blocked to maintain a loop-free topology. There are occasions when you do not want spanning tree to go through the steps mentioned above (listening, learning, and forward/blocking, which can take up to 45 seconds) but to immediately enter a forwarding state. For example, a PC with a fast processor connected to a switch does not need to test for any BPDUs (PCs do not run spanning tree), and the port on the Ethernet switch should enter a forwarding state to allow the PC immediate connectivity. This feature is known as portfast on Cisco switches. To enable portfast, use the Catalyst command set spantree <spantree number> portfast <interface> enable. NOTE Concurrent Routing and Bridging/Integrated Routing and Bridging, Routing Information Fields, Source Route Bridging, and Source Route Translation Bridging are not covered in the CCIE Security written exam, and they are not part of the blueprint. FastEther Channel FastEther Channel (FEC) is a Cisco method that bundles 100 Mbps FAST ETHERNET ports into a logical link. Because any redundant paths between two switches mean some ports will be in a blocking state and bandwidth will be reduced, Cisco developed FEC to maximize bandwidth use.
- 55. 32 Chapter 2: General Networking Topics Figure 2-4 displays a switched network with two 100-Mbps connections between them. Be- cause of STP, the link will be in a blocking state after the election of a root bridge, Switch A, in this case. Switch B will block one of the paths to ensure only one path (Switch A) to the root bridge. To purchase and enable a Fast Ethernet port is expensive, and to have it sitting in an idle position means wasted resources, so Cisco developed a method where Fast Ethernet ports could be bundled together and used concurrently (in other words, cheating spanning tree into believ- ing that the two ports are one to send data from Switch A to Switch B with two 100-Mbps links instead of one). Figure 2-4 Spanning Tree Loop Avoidance Switch A Switch B Set spantree priority 0 Default priority 32768 1/1 Forwarding Forwarding 1/1 1/2 Forwarding Blocking 1/2 I am the root One port will block on bridge so I forward Switch B to avoid loop on all ports. to root bridge. To enable FastEther Channel, the following steps are required: Step 1 All ports that are part of FEC must be set to the same speed. Step 2 All ports must belong to the same VLAN. Step 3 Duplex must be the same, half or full, not a mixture. Step 4 Bundle up to eight ports together. Step 5 To set FastEther channel on a switch, the CatOS syntax is set port channel. Step 6 To set FastEther Channel on a router, the IOS syntax is channel-group under the Fast Ethernet interface. Step 7 You are allowed up to four FEC groups per switch. This could change with future Catalyst releases.
- 56. Internet Protocol 33 NOTE A group of bundled ports running FEC is commonly known as a trunk. In switching terms, a trunk is a physical and logical connection between two switches. Inter-Switch Link (ISL) is a Cisco proprietary protocol that maintains VLAN information as traffic flows between switches and routers. ISL allows members of one VLAN to be located on any given switch. 802.1Q is an IEEE standard for trunking. You can use IEEE 802.1q in a multivendor environment. Figure 2-5 displays the logical link when FEC is enabled between Switch A and Switch B. Figure 2-5 FEC: Logical Link or Trunk-Enabled Set port channel 1/1 on Set port channel 1/1 on Set port channel 1/2 on Set port channel 1/2 on 1/1 Forwarding Forwarding 1/1 1/2 Forwarding Forwarding 1/2 Ports are bundled together; Both ports forwarding effective bandwidth now up now when FEC to 400 Mbps at full duplex is configured. instead of 200 Mbps. Internet Protocol Internet Protocol (IP) is a widely used networking term that describes a network layer protocol that logically defines a distinct host or end system, such as a PC or router, with an IP address. An IP address is configured on end systems to allow communication between hosts over wide geographic locations. An IP address is 32 bits in length, with the network mask or subnet mask (also 32 bits in length) defining the host and subnet portion. Figure 2-6 displays the IP packet header frame format in detail.
- 57. 34 Chapter 2: General Networking Topics Figure 2-6 IP Frame Format 32 bits Version IML Type of Service Total Length Identification Flags Fragment Offset Time-To-Live Protocol Header Checksum Source Address (32 bits) Destination Address (32 bits) Options (+ Padding) Data (Variable) The following describes the IP packet fields illustrated in Figure 2-6: • Version—Indicates the version of IP currently used. IPv4 is the most widely used version. IPv6 is also available. This version is not tested in the CCIE Security written exam yet, but will most likely be included in the future. • IP Header Length (IHL)—Indicates the datagram header length in 32-bit words. • Type-of-Service (ToS)—Specifies how an upper-layer protocol wants current datagrams to be handled and assigns datagrams various levels of importance. The ToS field (8 bits) defines the first 3 bits for precedence, of which there are eight possible values: — 000—Routine delivery — 001—Priority — 010—Immediate — 011—Flash — 100—Flash override
- 58. Internet Protocol 35 — 101—Critic — 110—Internetwork control — 111—Network control Typically, IP packets are set with the value 000. The remaining 5 bits in the ToS are defined as follows: — Bit 3—D bit defines normal or low delay. — Bit 4—T bit defines normal or low throughput. — Bit 5—R bit defines normal or low reliability. — Bits 6 and 7—Not in current use. • Total Length—Specifies the entire packet’s length in bytes, including the data and header. The mathematically defined limit is calculated as 65,535 bytes (216–1). • Identification—Contains an integer that identifies the current datagram. This field helps piece together datagram fragments (16 bits in length). • Flags—Consists of a 3-bit field of which the two low-order (least-significant) bits control fragmentation. The low-order bit specifies whether the packet can be fragmented. The middle bit specifies whether the packet is the last fragment in a series of fragmented packets. The third, or high-order, bit is not used. • Fragment Offset—Indicates the position of the fragment’s data relative to the beginning of the data in the original datagram, which allows the destination IP process to properly reconstruct the original datagram. • Time-to-Live—Maintains a counter that gradually decrements to 0, at which point the datagram is discarded. This keeps packets from looping endlessly. Cisco’s implementa- tion of the Cisco IOS Trace command works on TTL. • Protocol—Indicates which upper-layer protocol receives incoming packets after IP pro- cessing is complete. For TCP, this value is 6; for GRE, it is 47; for ICMP, it is 1; and for OSPF, the value is 89; these are common uses in today’s networks. • Header Checksum—Helps ensure IP header integrity only and not the data field. • Source Address—Specifies the sending node (32 bits). • Destination Address—Specifies the receiving node (32 bits). • Options—Allows IP to support various options, such as security. The Option field varies in length. Some options are Security, Loose Source Routing, Strict Source Routing, Record Route, and Timestamp. • Data—Contains upper-layer information.
- 59. 36 Chapter 2: General Networking Topics NOTE A subnet is a network that is segmented by network administrators, allowing a hierarchical routing topology. Subnetting allows great use of IP address space using binary bits from the subnet mask. Examples of subnets appear later in this chapter. Routing allows communication between these subnets. The host address is a logical, unique address that resides on a subnet. The Internet Engineering Task Force (IETF) standards body, which is a task force consisting of over 80 working groups responsible for developing Internet standards, has defined five address classes and the appropriate address ranges. Table 2-3 displays the five ranges. Table 2-3 Class A, B, C, D, and E Ranges Class of Address Starting Bit Pattern Range Default Subnet Mask Class A 0xxxxxxx 1-126, 127* 255.0.0.0 Class B 10xxxxxx 128-191 255.255.0.0 Class C 110xxxxx 192-223 255.255.255.0 Class D 1110xxxx 224-239 255.255.255.240 Class E 1111xxxx 240-255 Reserved * 127.0.0.0 is reserved for loopback purposes. Other reserved addresses for private use as defined by RFC 1918 are as follows: 10.0.0.0-10.255.255.255 172.16.0.0-172.31.255.255 192.168.0.0-192.168.255.255 Soon after these ranges were defined and the Internet’s popularity extended beyond the Depart- ment of Defense in the United States, it became clear that to ensure that a larger community could connect to the World Wide Web, there had to be a way to extend IP address space using subnetting. Subnetting allows an administrator to extend the boundary for any given subnet. To understand an IP address and subnet portion, to determine how many hosts are available on a particular subnet, to learn how to best utilize an IP address space, consider the following example. Suppose you are given the IP address 131.108.1.56 and the subnet mask is 255.255.255.0. This example will help you determine the subnet, how many hosts can reside on this subnet, and the broadcast address. You can deduce the subnet for any IP address by performing a logical AND operation for the IP address along with the subnet mask.
- 60. Internet Protocol 37 NOTE A logical AND operation follows two basic rules. One is that positive and positive equal positive, and the second is that negative and either positive or negative equal negative. In binary (positive is 1 and negative is 0), 0 AND 0 is 0, 0 AND 1 is 0, 1 AND 1 is 1, and 1 AND 0 is 0. Figure 2-7 displays the logical AND operation used to determine the subnet address. Figure 2-7 Logical AND Operation IP Address (131.108.1.56) 1 0 0 0 0 0 1 1 .1 1 0 0 1 1 0 0 .0 0 0 0 0 0 0 1 . 0 0 1 1 1 0 0 0 IP Subnet Mask (255.255.255.0) 1 1 1 1 1 1 1 1 .1 1 1 1 1 1 1 1 .1 1 1 1 1 1 1 1 . 0 0 0 0 0 0 0 0 Logical AND 1 0 0 0 0 0 1 1 .1 1 0 0 1 1 0 0 .0 0 0 0 0 0 0 1 . 0 0 0 0 0 0 0 0 In Decimal 131 108 1 0 The result of the logical AND operation reveals that the subnet address is 131.108.1.0. The subnet address is reserved and cannot be assigned to end devices. To determine the number of hosts available in any given subnet, simply apply the formula 2n–2, where n is the number of borrowed bits. This is best explained with examples. To determine the number of borrowed bits, you must examine the subnet mask in binary. For a default Class C network mask of 255.255.255.0, the last 8 bits represent the borrowed bits. For a Class C network, the number of hosts that can reside are 28–2 = 256–2 = 254 hosts. You subtract 2 host addresses because host devices are not permitted to use the subnet address or the broadcast address. In IP, a broadcast address consists of all binary 1s. So, for this example, the broadcast address for the subnet 131.108.1.0 is 131.108.1.255 (255 in binary is 11111111). Consider another example. Given the host address 171.224.10.67 and the subnet mask of 255.255.255.224, this example shows you how to determine the subnet and the number of hosts that can reside on this network. To determine the subnet, perform a logical AND. Figure 2-8 displays the operation. Figure 2-8 LOGICAL AND Operation IP Address (171.224.10.67) 10101011. 11100000. 00001010. 01000011 IP Subnet Mask (255.255.255.224) 1 1 1 1 1 1 1 1 . 1 1 1 1 1 1 1 1 . 1 1 1 1 1 1 1 1 . 1 1 1 0 0 0 0 0 Logical AND 10101011. 11100000. 00001010. 01000000 In Decimal 171 224 10 64 The subnet is 171.224.10.64. The number of hosts that can reside on this network with a subnet mask of 255.255.255.224 (or 11100000, 5 borrow bits) is 25–2 = 32–2 = 30 hosts. You can apply this simple example to any Class A, B, or C address, and applying a subnet mask that is not the
- 61. 38 Chapter 2: General Networking Topics default or classful kind allows network administrators to extend IP address space and allow a larger number of devices to connect to the IP network. Table 2-4 displays some common network subnets and the number of hosts available on those subnets. Table 2-4 Common Subnets in Today’s Networks Decimal Subnets Hosts 252 (1111 1100) 64 subnets 2 hosts* 248 (1111 1000) 32 subnets 6 hosts 240 (1111 0000) 16 subnets 14 hosts 224 (1110 0000) 8 subnets 30 hosts 192 (1100 0000) 4 subnets 62 hosts 128 (1000 0000) 2 subnets 126 hosts *Used commonly for point to point -ad WAN circuits when no more than two hosts reside. Variable-Length Subnet Masks A variable-length subnet mask (VLSM) is designed to allow greater use of IP address space by borrowing bits from the subnet mask and allocating them to host devices. To allow a greater number of devices to connect to the Internet and intranets, the standards body of various routing protocols designed an IP routing algorithm to cater to IP networks with a different subnet mask than the default used in classful networks. NOTE Routing algorithms that support VLSM are as follows: • RIP Version 2 • OSPF • IS-IS • EIGRP • BGP4 Additionally, Cisco IOS allows the use of any 0 subnets (for example, subnet 131.108.0.0/24) with the global IOS command, ip subnet-zero. This can be very useful for networks running out of IP address space.
- 62. Classless Interdomain Routing 39 To effectively use any IP address space, use the least number of subnet bits and least number of host bits. You could use a Class C mask or a mask that allows for 254 hosts. For a WAN link that will never use more than two hosts, this is a vast amount of wasted space. Applying different masks to cater to the exact requirement means that IP address space is not wasted unnecessarily. Apply the formula to determine the best subnet to use to cater to two hosts on any given subnet and class of address. Remember that you must subtract two host addresses for the subnet address and broadcast address. Applying the formula, you get 2n–2 = 2, or 2n = 4, or n = 2 borrowed bits. You need to borrow only 2 bits from the subnet mask to allow for 2 host addresses. The subnet mask is 30 bits in length, or 255.255.255.252 in binary. This is represented as 11111111.11111111.11111111.111111100. The last 2 bits (00) are available for host addresses. The subnet is 00, the first host address is 01, the second is 10, and the broadcast address is 11. TIP Loopback interfaces configured on Cisco routers are typically configured with a host address using a 32-bit subnet mask. This allows, for example, a Class C network with 255 hosts among 255 different routers and conserves valuable IP address space. Classless Interdomain Routing Classless interdomain routing (CIDR) is a technique supported by BGP4 and based on route aggregation. CIDR allows routers to group routes together to reduce the quantity of routing information carried by the core routers. With CIDR, several IP networks appear to networks outside the group as a single, larger entity. With CIDR, IP addresses and their subnet masks are written as four octets, separated by periods, and followed by a forward slash and a two-digit number that represents the subnet mask. CIDR representation can be either a forward slash with a one-digit number or a forward slash with a two-digit number (for example, 131.108.1/24 or 131.0.0.0/8). In the past few years, the expansion of the Internet has been phenomenal. Currently, the Internet uses more than 100,000 routes. From 1994 through 1996, the routing table increased from approximately 20,000 entries to more than 42,000. Currently, there are over 80,000 IP routing entries. How can network administrators reduce the large routing table size? Each routing entry requires memory and a table lookup by the router each time a packet is required to reach a des- tination. Reducing memory requirements and the time it takes to send a packet to the destination provides faster response times for packets to travel around the Internet. CIDR helps to reduce the number of routing table entries and memory requirements. CIDR helps conserve resources because it removes the limitation of using the default mask (which wastes IP address space) and leaves the addressing up to the IP designer. Routers use CIDR to group networks together to reduce routing table size and memory requirements. CIDR is
- 63. 40 Chapter 2: General Networking Topics typically represented with the network number/bits used in the mask, such as 131.108.1.0/24, or the equivalent of 131.108.1.0 255.255.255.0. BGP and classless routing protocols use CIDR to reduce routing table entries, allowing faster lookup and less memory requirement on Cisco routers, for example. Classful and Classless Routing Protocols Routing protocols can also be classed or described as classful and classless. Classful addressing, namely Classes A, B, and C (Class D is reserved for multicasts and Class E is reserved for future use), defines a set number of binary bits for the subnet portion. For example, a Class A network ranges from 1 to 127 and uses a subnet mask of 255.0.0.0. A Class B network uses the mask 255.255.0.0, and a Class C uses 255.255.255.0. Classful routing protocols apply the same rules. If a router is configured with a Class A address of 10.1.1.0, the default mask of 255.0.0.0 is applied, and so forth. This routing method does not scale well, so to design networks to better utilize address space, you have classless routing, which enables the network designer to apply different masks to Class A, B, and C networks to better utilize address space. For example, you can use a Class B network, such as 131.108.0.0, and apply a Class C mask (255.255.255.0 or /24 mask). Classful routing protocol examples include RIP and IGRP. Examples of classless routing protocols are OSPF, IS-IS, EIGRP, and BGP. With classless routing, the ability to apply summarization techniques allows for a reduction in routing table size. Over 100,000 IP routing table entries exist on the Internet. Reducing the IP route table size allows for faster delivery of IP packets and lower memory requirements. BGP is commonly referred to as a path vector protocol. To accomplish CIDR, you must allocate subnets at the common bit boundary, ensuring that your networks are continuous. For example, allocating 131.108.0.0/22 in one location and 131.108.1.0/24 to another will result is a discontinuous allocation and will not allocate CIDR to work properly. Transmission Control Protocol Transmission Control Protocol (TCP) is the most widely used protocol today, and all Cisco certification exams will test your understanding of TCP/IP. This section covers TCP and how this connection-oriented protocol ensures efficient delivery of data across an IP network. The TCP/IP model actually does not fully conform to the OSI model because IP was developed by the Department of Defense in the 1980s. IP provides each host device with a 32-bit host address that is used to route across the IP network. TCP is a Layer 4 protocol that ensures data is delivered across any IP cloud by using mecha- nisms such as connection startup, flow control, slow start (a congestion avoidance scheme in TCP in which a host can increase the window size upon arrival of an acknowledgment), and acknowledgments. UDP is the connectionless protocol for applications such as a TFTP transfer.
- 64. Transmission Control Protocol 41 TCP Mechanisms Figure 2-9 displays the TCP header format. Figure 2-9 TCP Header Format Source Port Destination Port Sequence Number Acknowledgment Number Data Offset Reserved Flags Window Checksum Urgent Pointer Options (+ Padding) Data (Variable) The following descriptions summarize the TCP packet fields illustrated in Figure 2-9: • Source Port and Destination Port—Identifies points at which upper-layer source and destination processes receive TCP services (16 bits in length). Common destination ports include 23 for Telnet, 21 for FTP, and 20 for FTP data. • Sequence Number—Usually specifies the number assigned to the first byte of data in the current message. In the connection-establishment phase, this field can also identify an initial sequence number to be used in an upcoming transmission. • Acknowledgment Number—Contains the sequence number of the next byte of data that the sender of the packet expects to receive. • Data Offset—Indicates the number of 32-bit words in the TCP header. • Reserved—Remains reserved for future use. • Flags—Carries a variety of control information, including the SYN and ACK bits used for connection establishment, and the FIN bit used for connection termination.
- 65. 42 Chapter 2: General Networking Topics • Window—Specifies the size of the sender’s receive window (that is, the buffer space available for incoming data). • Checksum—Indicates whether the header was damaged in transit. • Urgent Pointer—Points to the first urgent data byte in the packet. • Options—Specifies various TCP options. • Data—Contains upper-layer information. A number of mechanisms are used by TCP to ensure the reliable delivery of data, including the following: • Flags • Acknowledgments • Sequences numbering • Checksum • Windowing NOTE The Flags field is critical in a TCP segment. The field’s various options include the following: • URG (U) (Urgent)—Informs the other station that urgent data is being carried. The receiver will decide what to do with the data. • ACK (A) (Acknowledge)—Indicates that the packet is an acknowledgment of received data, and the acknowledgment number is valid. • PSH (P) (Push)—Informs the end station to send data to the application layer immediately. • RST (R) (Reset)—Resets an existing connection. • SYN (S) (Synchronize)—Initiates a connection, commonly known as established. • FIN (F) (Finished)—Indicates that the sender is finished sending data and terminates the session. To best describe how TCP is set up and established, consider a Telnet request from a PC to a Cisco router and follow the flags, acknowledgments, sequence, and windowing options. Figure 2-10 displays a typical Telnet session between a PC and a Cisco router. The PC initializes a Telnet request using destination port 23 and an initial sequence number.
- 66. Transmission Control Protocol 43 Figure 2-10 Telnet (TCP) Packet Flow Ethernet Segment PC Router Step 1 PC requests Telnet session. Connection Flags U A P R S F Request (SYN) 0 0 0 0 0 0 Destination Port is 23 or Telnet. Initial sequence is 14810532. Ack set to 0. Step 2 Connection Router responds with its Reply (ACK and SYN) own sequence number, and acknowledges the segment by increasing the PC sequence number by one. Flags U A P R S F 0 1 0 0 0 0 Source port is 23. Ack is 14810533. Step 3 PC acknowledges Its own sequence is Flags U A P R S F Router (ACK) 3646346918. 0 1 0 0 0 0 Sequence is 14810533. Ack set to 364639619. Step 4 Data Flow PC tears down Step 5 session (FIN) Flags U A P R S F 0 1 1 0 0 0 (ACK) Step 6 Router acknowledges request. (FIN) Step 7 Router also tears down connection. Flags U A P R S F Step 8 (ACK) 0 1 1 0 0 1 PC acknowledges request. Note: It takes 3 or 4 TCP segments to open a Telnet session and 4 TCP segments to close it.
- 67. 44 Chapter 2: General Networking Topics The following steps are then taken by TCP: Step 1 A user on the PC initiates a Telnet session to the router. The PC sends a request with the SYN bit sent to 1. The destination port number is 23 (Telnet). The PC will also place an initial sequence number (in this case, random number 14810532) in the segment. Step 2 The router responds with its own sequence number (such as, 3646349618) and acknowledges (ACK) the segment sent by the PC. The ACK will be the next expected sequence number generated by the PC; in this example, the ACK is numbered 14810533. Step 3 The PC sends a segment that acknowledges (ACK) the router’s reply. The first three steps are commonly known as the TCP three-way handshake. It is possible for four packets to start a session if a parameter needs to be negotiated. Step 4 Data is transferred. The window size can be adjusted according to the PC or the router. The windows size, for example, might be four packets before an acknowledgment is required. The sender waits for an acknowledgment before sending the next four segments. The window size can change during a data transfer; this is commonly known as the sliding window. If, for example, a lot of bandwidth is available, the sender might resize the window to eight segments. Or the sender might resize the window to two segments during periods of high congestion. The ACK (acknowledge) sent by the receiver is the next expected segment. This indicates that all previous segments have been received and reassembled. If any segment is lost during this phase, TCP can renegotiate the time waited before receiving the ACK and resend any lost segments. Step 5 After the PC completes the data transfer, the Telnet session is closed by sending a TCP segment with the FIN flag set to 1. Step 6 The router acknowledges (ACK) the request. Step 7 At this stage, the session is still open and the router could send data (this is known as TCP half close), but the router has no data to send and usually sends a segment with the FIN bit set to 1. Step 8 The PC acknowledges the router’s FIN request, and the Telnet session is closed. At any stage, the session can be terminated if either host sends a reset (RST flags in the TCP header); in this case, the session must be reestablished from scratch.
- 68. TCP Services 45 NOTE You need to know the TCP process and how packets are sequenced and acknowledged. TCP acknowledgments specify the next expected segment from a sender. A TCP session requires three or four segments to start (known as three-way handshake) and four segments to shut down. TCP Services This section covers common TCP services or applications used in today’s large IP networks: • Address Resolution Protocol (ARP) • Reverse Address Resolution Protocol (RARP) • Dynamic Host Configuration Protocol (DHCP) • Hot Standby Router Protocol (HSRP) • Internet Control Message Protocol (ICMP) • Telnet • File Transfer Protocol (FTP) • Trivial File Transfer Protocol (TFTP) Address Resolution Protocol (ARP) ARP determines a host’s MAC address when the IP address is known. For example, to ping one device from another, the Layer 2 MAC fields require a destination MAC address. Because this is the first such request, a broadcast packet is sent across the wire to discover the remote host’s MAC address. Figure 2-11 displays a scenario where PC1 wants to ping Host PC2. Figure 2-11 ARP Request IP address 1.1.1.3 MAC address 3333.3333.3333 Router A PC1 PC2 IP address 1.1.1.1 IP address 1.1.1.2 MAC address 1111.1111.1111 MAC address 2222.2222.2222
- 69. 46 Chapter 2: General Networking Topics When PC1 sends a ping request to PC2 using the known IP address 1.1.1.2 (Layer 3), a broadcast Layer 2 frame is sent to the destination address FF-FF-FF-FF-FF-FF, and ARP (the ARP frame contains the source MAC address and the source IP address) is sent to all devices requesting the Layer 2 MAC address of the device configured with the IP address 1.1.1.2 (by sending a Layer 2 broadcast frame). PC2 responds to the ARP request with its source MAC address, 2222.2222.2222. PC1 now has PC2’s MAC address and sends a packet to the destination address, 2222.2222.2222, and Layer 3 destination address, 1.1.1.2. NOTE A less common ARP term used in ARP terminology is a gratuitous ARP. A gratuitous ARP is an ARP request with its own IP address as the target address. It refreshes a device’s ARP table entries and also looks up duplicate IP addresses. Routers are devices that can send a gratuitous ARP. To view the IP ARP table on a Cisco router, the command is show ip arp. The IP ARP table from Figure 2-11 is displayed in Example 2-2. Example 2-2 show ip arp Command on Router A RouterA#show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 1.1.1.3 - 3333.3333.3333 ARPA Ethernet0 Internet 1.1.1.1 170 1111.1111.1111 ARPA Ethernet0 Internet 1.1.1.2 94 2222.2222.2222 ARPA Ethernet0 NOTE If you’ve ever wondered why the first ping request on a Cisco router fails, it’s because an ARP request is sent first when an entry is not present in the ARP table. Subsequent pings will have 100 percent success. Reverse ARP Reverse ARP (RARP) is when a device boots up without an IP address and requests an IP address. Reverse ARP is typically not used in today’s networks, and is replaced by DHCP. Dynamic Host Configuration Protocol Dynamic Host Configuration Protocol (DHCP) is defined in RFC 1531 (latest RFC 2131) and provides a comprehensive method of allocating IP addresses, subnet mask, gateway address, DNS server, WINS servers, and many more parameters for IP devices.
- 70. TCP Services 47 DHCP clients send messages to the server on UDP 67, and servers send messages to the client on UDP 68. Cisco routers can also be configured for DHCP. Example 2-3 configures a Cisco IOS router to allocate the entire range 131.108.1.0/24, with a gateway address 131.108.1.1, subnet mask 255.255.255.0, DNS servers 141.108.1.1 and 141.108.1.2, domain name cisco.com, and WINS (for Windows 2000 clients) server addresses 64.104.1.1 and 141.108.2.1. The lease should last forever, so the final command is lease infinite. Example 2-3 DHCP Configuration on Cisco IOS Router R1#sh running-config | begin dhcp ip dhcp excluded-address 131.108.1.1 Interface Ethernet 0 ip address 131.108.1.1 255.255.255.0 ! ip dhcp pool DHCPpool network 131.108.1.0 255.255.255.0 dns-server 141.108.1.1 141.108.1.2 domain-name cisco.com default-router 148.16.36.6 148.16.36.3 netbios-name-server 64.104.1.1 141.108.2.1 lease infinite To view the DHCP leases, use the IOS command show ip dhcp server. Example 2-4 displays the output taken from a router configured for DHCP. Example 2-4 show ip dhcp server Sample Display R1#show ip dhcp server DHCP server: ANY (255.255.255.255) Leases: 200 Offers: 200 Requests: 400 Acks: 330 Naks: 230 Declines: 0 Releases: 0 Bad: 0 Example 2-4 shows that 200 devices are currently allocated IP addresses, and over 400 requests were made. Hot Standby Router Protocol HSRP allows networks with more than one gateway to provide redundancy in case of interface or router failure on any given router. HSRP allows router redundancy in a network. It is a Cisco proprietary solution from before the IETF defined Virtual Router Redundancy Protocol (VRRP). To illustrate HSRP, Figure 2-12 displays a six-router network with clients on segments on Ethernet networks, Sydney and San Jose.
- 71. 48 Chapter 2: General Networking Topics NOTE Cisco exams typically test Cisco proprietary protocols more heavily than industry standard protocols, such as VRRP. To my knowledge, VRRP is not listed (or tested) as an objective on the Cisco website. Figure 2-12 HSRP Example Router A # Router C # interface Ethernet 0 interface Ethernet 0 ip address 131.108.1.1 255.225.255.0 ip address 131.108.1.2 255.225.255.0 standby priority 110 preempt standby priority 110 preempt standby authentication cisco standby authentication cisco standby ip 131.108.2.100 standby ip 131.108.1.100 standby track Serial0 standby track Serial0 Network E0 E0 Network Sydney 131.108.2.2/24 131.108.1.2/24 San Jose Serial 0 Serial 0 Router A Router B Router C Standby IP add 131.108.2.100 Standby IP add 131.108.1.100 PC2 PC1 IP Address IP Address 131.108.2.1/24 Router F Router E Router D 131.108.1.1/24 Gateway Address Gateway Address 131.108.2.100/24 Serial 0 Serial 0 131.108.1.100/24 E0 E0 131.108.2.2/24 131.108.1.2/24 Router F # Router D # interface Ethernet 0 interface Ethernet 0 ip address 131.108.2.2 255.225.255.0 ip address 131.108.1.3 255.225.255.0 standby authentication cisco standby authentication cisco standby ip 131.108.2.100 standby ip 131.108.2.100 !default not shown !default not shown standby priority 100 standby priority 100 PCs are typically configured with only one gateway address. (Windows 2000/XP clients can take more than one but this still leaves a problem in that all devices must be configured for multiple gateways; the most scalable solution is to configure a single gateway on all devices and allow an intelligent network to provide redundancy where only a few devices require configu- ration.) Assume that PC1 is configured with a gateway address of 131.108.1.100. Two routers
- 72. TCP Services 49 on the Ethernet share the segment labeled San Jose network. To take advantage of the two rout- ers, HSRP will allow only Routers C and D to bid for a virtual IP address, and if any one router (Router C or D, in this example) fails, the operational router assumes the HSRP gateway address. Host devices typically have only a brief 100 to –200-millisecond interruption when a network failure occurs. To illustrate how HSRP provides default gateway support, refer to Figure 2-12. In Figure 2-12, you can see a network with two local routers configured with an Ethernet interface address of 131.108.1.2/24 for Router C and 131.108.1.3/24 for Router D. Notice that both routers share a common Ethernet network. Assume that PC1 has been configured with a default gateway point- ing to Router C. If Router C goes down or the Ethernet interface becomes faulty, all the devices must be manually reconfigured to use the second default gateway (Router D, 131.108.1.3/24). HSRP enables the network administrator to elect one of the two routers to act as the default gateway. If the elected router goes down, the second router assumes the IP default gateway. The IOS command standby track interface-of-wan under the Ethernet interface allows the router to monitor the WAN link. If the WAN link continuously fails past a threshold, the HSRP default router will decrease its priority to allow a more reliable WAN connection to provide a gateway. For example, in Figure 2-12, if the link between Routers C and B fails past a threshold, Router D can be configured to assume the HSRP address to provide a faster connection to the IP back- bone network. The steps to enable HSRP are as follows: Step 1 Enable HSRP (required). Step 2 Configure HSRP group attributes (optional). Step 3 Change the HSRP MAC refresh interval (optional). Table 2-5 illustrates the various required and optional commands to enable HSRP. Table 2-5 HSRP Commands IOS Command Purpose standby [group-number] timers [msec] These required commands configure the time hellotime [msec] holdtime between hello packets and the hold time before other routers declare the active router to be down. standby [group-number] priority priority Sets the Hot Standby priority used in choosing the [preempt [delay [minimum | sync] delay]] active router. The priority value range is from 1 to or 255, where 1 denotes the lowest priority and 255 denotes the highest priority. Specifies that if the local standby [group-number] [priority priority] router has priority over the current active router, the preempt [delay [minimum | sync] delay] local router should attempt to take its place as the active router. Configures a preemption delay, after which the Hot Standby router preempts and becomes the active router. These commands are optional. continues
- 73. 50 Chapter 2: General Networking Topics Table 2-5 HSRP Commands (Continued) IOS Command Purpose standby [group-number] track type number This optional command configures the interface to [interface-priority] track other interfaces so that if one of the other interfaces goes down, the device’s Hot Standby priority is lowered. standby [group-number] authentication Selects an authentication string to be carried in all string HSRP messages. Optional authenticator field allows only authenticated routers to offer HSRP. standby use-bia [scope interface] Configures HSRP to use the burned-in address of an interface as its virtual MAC address instead of the preassigned MAC address (on Ethernet and FDDI), or the functional address (on Token Ring). Now configure Routers C and D in Figure 2-12 for HSRP, and ensure that Router C is the pri- mary gateway address and that the PC is configured with a gateway address of 131.108.1.100. Router C is configured with a higher priority (standby priority 110 preempt than the default standby preempt) 100 to ensure Router C becomes the default gateway for the hosts on the San Jose network; authentication is also enabled between the two gateway routers. Example 2-5 displays the sample IOS configuration for Router C. Example 2-5 HSRP Configuration on Router C interface Ethernet0 ip address 131.108.1.2 255.255.255.0 standby priority 110 preempt standby authentication cisco standby ip 131.108.1.100 standby track Serial0 Example 2-5 displays Router C configured with a virtual IP address of 131.108.1.100 and preempt, which allows Router C to assume the role if a failure occurs. The track command ensures that Serial0, or the WAN link to Router B, is monitored to make sure a flapping link does not cause bandwidth delays for users, such as PC1. For every tracked interface failure, the priority is reduced by 10 by default. The Cisco IOS default priority is set to 100. In this configuration, two failures must occur for Router D to assume the HSRP address (110–10–10=90<100). Example 2-6 displays the sample IOS configuration for Router D. Configure Router D with an HSRP priority of 105 so that any one (1 not 2) failure on Router C will mean that Router D priority is higher than Router C. (Router C is set to 105; one failure and then it is set to 105–10=95<100.)
- 74. TCP Services 51 Example 2-6 HSRP Configuration on Router D interface Ethernet0 ip address 131.108.1.3 255.255.255.0 standby authentication cisco standby ip 131.108.1.100 To view the status of HSRP, the IOS command is show standby. Example 2-7 displays the sample output when the IOS command show standby is entered in Router C. Example 2-7 show standby on Router C Router-C#show standby Ethernet - Group 0 Local state is Active, priority 105, may preempt Active 105 Hellotime 3 holdtime 10 Next hello sent in 00:00:01.967 Hot standby IP address is 131.108.1.100 configured Active router is local Standby router is unknown expired Standby virtual mac address is 0000.0c07.ac00 2 state changes, last state change 00:03:59 Tracking interface states for 1 interface, 0 up: up Serial0 Router C is currently the configured gateway and is tracking Serial 0 for failures; every WAN failure decrements the priority value by 10. If a single failure occurs, the priority on Router C will drop to 95 (105–10=95), and Router D will immediately remain the default gateway until the interface on Router C has fully recovered. After the priority on Router C increments back to 105, Router C assumes the gateway function because preempt is enabled, as displayed in Example 2-54. Example 2-8 displays the output of the show standby command on Router D. Example 2-8 show standby on Router D Router-D#show standby Ethernet - Group 0 Local state is Standby, priority 100, Standby Hellotime 3 holdtime 10 Next hello sent in 00:00:01.967 Hot standby IP address is 131.108.1.100 configured Active router is local Standby router is unknown expired Standby virtual mac address is 0000.0c07.ac00 2 state changes, last state change 00:03:59
- 75. 52 Chapter 2: General Networking Topics Internet Control Message Protocol Internet Control Message Protocol (ICMP) is a network layer (Layer 3) Internet protocol that reports errors and provides other information relevant to IP packet processing. ICMP is fully documented in RFC 792. ICMP’s purpose is to report error and control messages. ICMP provides a number of useful services supported by the TCP/IP protocol, including ping requests and replies. Ping requests and replies enable an administrator to test connectivity with a remote device. Be aware that ICMP runs over IP, which means that there is no guarantee of delivery (because IP is a connectionless protocol). Example 2-9 provides a sample ping command in which an administrator wants to see if a remote device is reachable by sending the remote device a ping request from a Cisco router. By default, a Cisco router will send out a series of five ICMP requests whenever the ping command is issued. Example 2-9 displays a sample ping request to the remote IP address 131.108.1.1 on Router R2. Example 2-9 ping 131.108.1.1R2>ping 131.108.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 131.108.1.1, !!!!! Success rate is 100 percent (5/5), R2> The ping command has a number of reporting mechanisms that run over ICMP. The exclama- tion point (!) indicates a successful reply. The ping command can also advise you, using a special code character, that the end device is not reachable, as depicted in Table 2-6. Table 2-6 Possible Test Characters When Using the ping Command Code Description ! Each exclamation point indicates the receipt of a reply. . Each period indicates that the network server timed out while waiting for a reply. U Destination unreachable. N Network unreachable. P Protocol unreachable. Q Source quench. M Could not fragment. ? Unknown packet type.
- 76. Routing Protocols 53 NOTE Cisco IOS provides a detailed version of the ping tool, which you can evoke by typing ping in the enabled mode. This command is known as the extended ping command. Telnet Telnet is an application layer protocol and part of the TCP/IP protocol suite. The TCP destina- tion port number is 23 and commonly manages routers and switches, for example. Telnet is an insecure protocol, as data flows in plain text and the Telnet passwords can be sniffed. SSH is more secure for remote logins. File Transfer Protocol and Trivial File Transfer Protocol File Transfer Protocol (FTP) and Trivial File Transfer Protocol (TFTP) are application layer protocols (part of the TCP/IP protocol suite of applications). FTP is a connection-oriented protocol running over TCP. FTP uses two connections to maintain connectivity between two IP hosts; port 20 is used for server applications and port 21 for data transfer. TFTP runs over UDP port 69 and is a connectionless-based protocol. TFTP commonly uploads IOS and configurations to a TFTP server. TFTP is regarded as the simple version of FTP. TFTP does not require any username/password combination to transfer data, as opposed to FTP, where a username and password are required before data can be transferred. NOTE Domain Name Server (DNS) is another common application that uses both TCP and UDP port 53. Now that you fully appreciate the TCP/IP model, the next section covers routing protocols used to ensure TCP/IP data can be moved, or routed, from one location to another. Routing Protocols This section covers four main routing protocols: • RIP • EIGRP • OSPF • BGP Before discussing the characteristic of each protocol, this section covers how routers (Cisco routers, in particular) generally route IP packets.
- 77. 54 Chapter 2: General Networking Topics Routing is a process whereby a path to a destination host is selected by either a dynamic or static routing protocol. A routing protocol is an algorithm that routes data across the network. Each router makes routing decisions from host to destination based on specific metrics used by the operating routing protocol. For example, RIP uses hop count (commonly known as the network diameter) to decide what router interface the data is sent. A lower hop count is always preferred. OSPF, on the other hand, uses a cost metric; the lower the cost, the more preferred a path to the destination. Routing IP across a network of Cisco routers requires IP address allocation to interfaces and then a static or dynamic routing protocol to advertise these networks to local or remote routers. After these networks are advertised, IP data can flow across the network. Routing occurs at Layer 3 (the network layer) of the OSI model. By default, IP routing is enabled on Cisco routers. The command used to start or disable IP routing is [no] ip routing. By default, IP routing is enabled so you will not see this command by viewing the configuration. Consider a one-router network with two directly connected Ethernet interfaces as an introductory example. Figure 2-13 displays a two-port Ethernet router configured with two subnets. Figure 2-13 Connected Routes Directly Connected Networks 172.108.1.1/24 R1 172.108.2.1/24 E0 E1 PC 1 PC 2 R1# show ip route Codes C- connected, S- static, I- IGRP, R- RIP, M- mobile, B- BGP D- EIGRP, EX- EIGRP external, Q- QSPF, 1A- OSPF inter area N1- OSPF NSSA external type 1, N2- OSPF NSSA external type 2 E1- OSPF external type 1, E2- OSPF external type 2, E- EGP i- IS-IS, L1- IS-IS level-1, L2- IS-IS level-2.*-candidate default U- per-user static route, o- ODR - Gateway of last resort is not set - 172.108.0.0/24 is subnetted, 2 subnets C 172.108.1.0 is directly connected, Ethernet0 C 172.108.2.0 is directly connected, Ethernet1 R1# PC1 can communicate with PC2 as shown in Figure 2-13, because Cisco routers will route to directly connected interfaces.
- 78. Routing Protocols 55 The IOS command show ip route is used to view the IP routing table, and a number of symbols define how remote or local networks have been discovered. Table 2-7 defines the various symbols and their meanings. The Cisco Documentation CD defines the routing fields or codes as follows. Table 2-7 show ip route Defined* Field Description O Indicates protocol that derived the route. Possible values include the following: I—IGRP derived R—RIP derived O—OSPF derived C—Connected S—Static E—EGP derived B—BGP derived D—EIGRP EX—EIGRP external I—IS-IS derived Ia—IS-IS M—Mobile P—Periodic downloaded static route U—Per-user static route O—On-demand routing E2 Type of route. Possible values include the following: *—Indicates the last path used when a packet was forwarded. It pertains only to the nonfast-switched packets. However, it does not indicate what path will be used next when forwarding a nonfast-switched packet, except when the paths are equal cost. IA—OSPF interarea route E1—OSPF external type 1 route E2—OSPF external type 2 route L1—IS-IS Level 1 route L2—IS-IS Level 2 route N1—OSPF NSSA external type 1 route N2—OSPF NSSA external type 2 route continues
- 79. 56 Chapter 2: General Networking Topics Table 2-7 show ip route Defined* (Continued) Field Description 172.108.0.0/24 is subnetted, 2 subnets Indicates the address of the remote network. C 172.108.1.0 is directly connected, Ethernet0 C 172.108.2.0 is directly connected, Ethernet1 R1# [160/5] The first number in the brackets is the information source’s administrative distance; the second number is the metric for the route. via Specifies the address of the next router to the remote network. 0:01:00 Specifies the last time the route was updated in hours:minutes:seconds. Ethernet0 Specifies the interface through which the specified network can be reached. * Part of this table taken from http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fiprrp_r/ind_r/1rfindp2.htm#102251, all rights are reserved to Cisco. By default, Cisco IOS assigns each routing protocol an administrative distance (AD) that indicates the trustworthiness of a routing entry if there is more than one path to a remote network running two or more routing algorithms. You can configure the AD value from the default with the distance administrative-distance IOS command if you want to manually choose RIP over OSPF, for example. The value for administrative-distance can be 1 to 255. Table 2-8 displays the administrative distances enabled by default on Cisco routers. Table 2-8 Default Administrative Distances Route Source Default Distance Connected interface (or static route via a 0 connected interface) Static route 1 Enhanced IGRP summary route 5 External BGP 20 Internal enhanced IGRP 90 IGRP 100
- 80. Routing Protocols 57 Table 2-8 Default Administrative Distances (Continued) Route Source Default Distance OSPF 110 IS-IS 115 RIP 120 EGP 140 EIGRP external route 170 Internal BGP 200 Unknown 255 For example, Table 2-8 demonstrates that an EIGRP (AD 90) route is preferred over a network entry discovered by RIP (AD 120) because the AD is lower, or more trustworthy. NOTE The IP address source and destination in an IP datagram does not alter, but the Layer 2 MAC source and destination do, for example, when PC1 sends a packet to PC2 in Figure 2-13. The TCP/IP software on PC1 identifies that the remote destination (172.108.2.0/24) is not locally connected and sends the Layer 3 frame to the local gateway address, 171.108.1.1/24. For the Layer 2 frame to transverse the local Ethernet, the destination Layer 2 Mac address must be that of the local router or gateway. PC2 resides on a different subnet, so the destination MAC address will be that of Router R1 (E0 burnt in address), or the default gateway address of 172.108.1.1. Router R1 will then strip the Layer 2 header and install its own Layer 2 header when the packet enters the network where PC2 resides. The Layer 2 header contains the source address (Layer 2) of R1 E1 and destination address of PC2’s MAC address. The Layer 3 IP source and destination addresses do not change during the routing of the IP packet. The excep- tion to changes in Layer 3 addressing is when Network Address Translation (NAT) is used. Routing Information Protocol Routing Information Protocol (RIP) is one the oldest routing protocols in use today. RIP is a distance vector protocol. Table 2-9 defines the characteristics of a distance vector protocol.
- 81. 58 Chapter 2: General Networking Topics Table 2-9 Distance Vector Protocol Characteristics Characteristic Description Periodic updates Periodic updates are sent at a set interval; for IP RIP, this interval is 30 seconds. Broadcast updates Updates are sent to the broadcast address 255.255.255.255. Only devices running routing algorithms will listen to these updates. Full table updates When an update is sent, the entire routing table is sent. Triggered updates Also known as Flash updates, these are sent when a change occurs outside the update interval. Split horizon This method stops routing loop. Updates are not sent out an outgoing interface from which the source network was received. This saves bandwidth, as well. Count to infinity Maximum hop count. For RIP, it’s 15, and for IGRP, it’s 255. Algorithm Example: Bellman-Ford for RIP. Examples RIP and IGRP. RIP comes in two versions: RIPv1 (does not support VLSM) and RIPv2. Both versions of RIP automatically summarize at the network boundary (you can configure classful routing protocol, RIPv2, to support VLSM). The following list summarizes RIPv1 characteristics: • Distance vector protocol • Runs over UDP port 520 • Metric is hop count (maximum is 15; 16 is unreachable) • Periodic updates every 30 seconds • Up to 25 networks per RIP update • Implements Split horizon • Implements triggered updates • No support for VLSM or authentication • Administrative Distance is 120 NOTE Split horizon is a routing technique in which information about routes is prevented from exiting the router interface through which that information was received. Split horizon updates are useful in preventing routing loops. To enable split horizon, the IOS command is ip split- horizon. Split horizon on frame relay subinterfaces is enabled by default. Always use the IOS command show ip interface to determine if split horizon is enabled or displayed.
- 82. Routing Protocols 59 A triggered update is a method by which a routing protocol sends an instant message as soon as a network failure is detected. If a triggered update were not used, the only way the update would be sent would be via the normal update every 30 seconds, causing a delay in network convergence times. Split horizon is a favorite topic in CCIE lab exams. Poison Reverse updates explicitly indicate that a network is unreachable rather than implying a remote network is unreachable by not sending that network in an update. Poison Reverse updates are intended to defeat routing loops in large IP networks. Split horizon, Poison Reverse, and triggered updates are methods used by distance vector protocols to avoid routing loops. RIPv2 was developed to enable RIP to support VLSM, so it is a classless routing protocol that also supports authentication. RIPv2 uses the same hop count and metric. The following list summarizes RIPv2 characteristics: • Distance vector protocol • Runs over UDP port 520 • Metric is hop count (maximum is 15; 16 is unreachable) • Periodic updates every 30 seconds • Up to 25 networks per RIP update • Implements Split horizon • Implements triggered updates • Supports VLSM (subnet mask carried in updates) • Supports authentication • Administrative Distance is 120 • Updates sent to multicast address 224.0.0.9 • Can set up neighbors to reduce broadcast traffic (send unicast updates) To enable RIP on a Cisco router, the command required is router rip. Consider a two-router topology running VLSM and RIP. Figure 2-14 displays two routers, named R1 and R2, with a /30-bit network used across the WAN. Loopbacks are used to populate the IP routing tables. To start, enable RIP on both routers with the commands in Example 2-10. Version 2 must be enabled because you are implementing VLSM across the WAN links between R1 and R2.
- 83. 60 Chapter 2: General Networking Topics Figure 2-14 Practical Example of Routing RIP 131.108.3.0/30 Frame Relay 172.108.1.1/24 172.108.2.1/24 E0/0 S0/0 S0/0 E0/0 R1 .1 .2 R2 R1's Loopbacks R2's Loopbacks Loopback0 131.108.4.1/24 Loopback0 131.108.7.1/24 Loopback1 131.108.5.1/24 Loopback1 131.108.8.1/24 Loopback2 131.108.6.1/24 Loopback2 131.108.9.1/24 Example 2-10 displays the RIP configuration on R1. The same configuration commands are applied to R2. Example 2-10 IP RIP Configuration on R1 router rip version 2 network 131.108.0.0 View the RIP forward database with the command, show ip rip database. Example 2-11 displays the output when show ip rip database is executed on R1. Example 2-11 show ip rip database Command on R1 R1#show ip rip database 131.108.0.0/16 auto-summary 131.108.1.0/24 directly connected, Ethernet0/0 131.108.2.0/24 [1] via 131.108.3.2, 00:00:12, Serial0/0 131.108.3.0/30 directly connected, Serial0/0 131.108.4.0/24 directly connected, Loopback0 131.108.5.0/24 directly connected, Loopback1 131.108.6.0/24 directly connected, Loopback2 131.108.7.0/24 [1] via 131.108.3.2, 00:00:12, Serial0/0 131.108.8.0/24 [1] via 131.108.3.2, 00:00:12, Serial0/0 131.108.9.0/24 [1] via 131.108.3.2, 00:00:12, Serial0/0
- 84. Routing Protocols 61 Example 2-11 displays the directly connected routers and the four dynamically discovered routers via Serial0/0 to R2. To confirm that the entries are reachable, display the IP routing table on R1 and perform a few ping requests across the Frame Relay cloud. Example 2-12 displays the IP routing table and the successful ping requests to the four remote networks. Example 2-12 show ip route and ping to R2 R1#show ip route Codes: C - connected, R - RIP, 131.108.0.0/16 is variably subnetted, 9 subnets, 2 masks R 131.108.9.0/24 [120/1] via 131.108.3.2, 00:00:00, Serial0/0 R 131.108.8.0/24 [120/1] via 131.108.3.2, 00:00:00, Serial0/0 R 131.108.7.0/24 [120/1] via 131.108.3.2, 00:00:00, Serial0/0 C 131.108.6.0/24 is directly connected, Loopback2 C 131.108.5.0/24 is directly connected, Loopback1 C 131.108.4.0/24 is directly connected, Loopback0 C 131.108.3.0/30 is directly connected, Serial0/0 R 131.108.2.0/24 [120/1] via 131.108.3.2, 00:00:01, Serial0/0 C 131.108.1.0/24 is directly connected, Ethernet0/0 R1#ping 131.108.2.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 131.108.2.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms R1#ping 131.108.7.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 131.108.7.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms R1#ping 131.108.8.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 131.108.8.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms R1#ping 131.108.9.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 131.108.9.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/5/8 ms R1# Example 2-12 displays the four remote networks reachable by the Serial 0/0 and four successful ping requests (five replies to each remote network) to those interfaces on R2. Stop R2 from sending R1 any updates via the Frame cloud to demonstrate the passive-interface command, passive-interface Serial0/0.
- 85. 62 Chapter 2: General Networking Topics Example 2-13 displays the passive interface configuration on R2 serial0/0. Example 2-13 Passive Interface Configuration on R2 R2(config)#router rip R2(config-router)#passive-interface serial 0/0 R1’s routing table now contains no remote entries from R2, which will still receive updates because the command affects only outbound updates. Example 2-14 confirms the missing routing RIP entries in R1’s IP routing table. Example 2-14 show ip route on R1 R1#show ip route Codes: C - connected, 131.108.0.0/16 is variably subnetted, 5 subnets, 2 masks C 131.108.6.0/24 is directly connected, Loopback2 C 131.108.5.0/24 is directly connected, Loopback1 C 131.108.4.0/24 is directly connected, Loopback0 C 131.108.3.0/30 is directly connected, Serial0/0 C 131.108.1.0/24 is directly connected, Ethernet0/0 EIGRP EIGRP is a Cisco-developed routing protocol that uses the same metric defined by IGRP mul- tiplied by 256. The routing metric in EIGRP is based on bandwidth, delay, load, and reliability. The CCIE Security written exam does not test the candidates’ understanding of EIGRP too greatly, so this section includes only the relevant topics for the exam. EIGRP is a Cisco proprietary routing protocol that can be used to route a number of Layer 3 protocols, including IP, IPX, and AppleTalk. This section is concerned only with routing IP. To ensure EIGRP is as efficient as possible, the following features were built into EIGRP: • Rapid convergence—EIGRP uses the Diffusing Update Algorithm (DUAL) to achieve rapid convergence. A Cisco IOS router that runs EIGRP will ensure any redundant paths are stored and used in case of a network failure. • Reduced bandwidth usage—By default, EIGRP uses up to 50 percent of available bandwidth, and this option can be changed with the IOS command ip bandwidth-percent eigrp as-number percent. By default, EIGRP uses up to 50 percent of the bandwidth defined by the interface bandwidth command. The interface command, ip eigrp- bandwidth-percent <0-100%>, can be used to change this value (a good method to use for the CCIE lab). EIGRP is consider a hybrid routing protocol, meaning that EIGRP uses characteristics of both distance vector and link-state routing protocols to maintain routing tables.
- 86. Routing Protocols 63 EIGRP Terminology EIGRP has a number of terms that must be understood by a candidate for the CCIE Security written exam. Table 2-10 defines some of the common terminology used in EIGRP. Table 2-10 EIGRP Terms Term Meaning Neighbor A router in the same autonomous system (AS) running EIGRP. Neighbor table EIGRP maintains a table with all adjacent routers. To view the EIGRP neighbors, use the IOS command show ip eigrp neighbors. Topology table EIGRP maintains a topology table for all remote destinations discovered by neighboring routers. To view the topology table, the IOS command is show ip eigrp topology. Hello A packet used to monitor and maintain EIGRP neighbor relationships; they are multicast. Query A query packet that is sent to neighboring routers when a network path is lost; can be multicast or unicast. Reply A reply packet to a query packet; they are unicast. ACK Acknowledgment of an update packet, typically a hello packet with no data; they are unicast. Holdtime How long a router waits for a hello packet before tearing down a neighbor adjacency. Smooth Route Trip Time (SRTT) Time taken to send a packet reliably to an acknowledgment. SRTT is the average delta between the time a packet is sent and the arrival of the neighbor’s acknowledgment. Retransmission Timeout (RTO) RTO is the time a router waits for the arrival of the neighbor’s acknowledgment. Feasible distance Lowest metric to remote network. Feasibility condition (FC) A condition under which the sum of a neighbor’s cost to a destination and the cost to this neighbor is less than current successor’s cost. Feasible successor A neighboring router with a lower AD. Successor A neighboring router that meets the feasibility condition. Stuck in Active (SIA) An EIGRP router waiting for all acknowledgments from neighboring routers for all the queries sent. Active When a router is querying neighboring routers about a network path. Passive Normal route operation to a remote destination.
- 87. 64 Chapter 2: General Networking Topics EIGRP Configuration Example Configure a two-router EIGRP network with two Frame Relay links between two routers to demonstrate the redundancy mechanism with the EIGRP DUAL algorithm. Figure 2-15 displays a two-router topology using the same addressing as the RIP example in Figure 2-14. Figure 2-15 EIGRP Configuration Example Autonomous System 100 (AS100) Bandwidth 256 131.108.3.0/30 Frame Relay 172.108.1.1/24 S0/0 S0/0 172.108.2.1/24 .1 .2 E0/0 S0/1 S0/1 E0/0 R1 R2 .1 131.108.10.0/30 .2 Bandwidth Frame Relay 128 R1's Loopbacks R2's Loopbacks Loopback0 131.108.4.1/24 Loopback0 131.108.7.1/24 Loopback1 131.108.5.1/24 Loopback1 131.108.8.1/24 Loopback2 131.108.6.1/24 Loopback2 131.108.9.1/24 Routers R1 and R2 reside in AS 100, and to enable EIGRP on both routers, you need to start by configuring EIGRP. Example 2-15 displays the EIGRP configuration required on R1 and R2. Example 2-15 Enabling EIGRP in AS 100 router eigrp 100 network 131.108.0.0 The network command in Example 2-15 enables EIGRP to send and receive updates for interfaces configured with the Class B address, 131.108.0.0. EIGRP will automatically summarize. Example 2-16 displays the IP routing table on R1. Example 2-16 show ip route on R1 R1#show ip route Codes: C - connected, D - EIGRP, EX - EIGRP external, 131.108.0.0/16 is variably subnetted, 10 subnets, 2 masks C 131.108.10.0/30 is directly connected, Serial0/1
- 88. Routing Protocols 65 Example 2-16 show ip route on R1 (Continued) D 131.108.9.0/24 [90/10639872] via 131.108.3.2, 00:04:27, Serial0/0 D 131.108.8.0/24 [90/10639872] via 131.108.3.2, 00:04:27, Serial0/0 D 131.108.7.0/24 [90/10639872] via 131.108.3.2, 00:04:27, Serial0/0 C 131.108.6.0/24 is directly connected, Loopback2 C 131.108.5.0/24 is directly connected, Loopback1 C 131.108.4.0/24 is directly connected, Loopback0 C 131.108.3.0/30 is directly connected, Serial0/0 D 131.108.2.0/24 [90/10537472] via 131.108.3.2, 00:04:28, Serial0/0 C 131.108.1.0/24 is directly connected, Ethernet0/0 Example 2-16 displays four remote EIGRP entries (designated by D in the routing table) via the Serial interface Serial0/0. EIGRP has discovered these networks as the preferred path because the WAN bandwidth is 256 kbps as opposed to 128 kbps via Serial 0/1. To view the alternate paths, use the show ip eigrp topology IOS command to display backup paths. Example 2-17 displays the output of the show ip eigrp topology command on R1. Example 2-17 show ip eigrp topology on R1 R1#show ip eigrp topology IP-EIGRP Topology Table for AS(100)/ID(131.108.6.1) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 131.108.10.0/30, 1 successors, FD is 2169856 via Connected, Serial0/1 via 131.108.3.2 (11023872/1761792), Serial0/0 P 131.108.9.0/24, 1 successors, FD is 2297856 via 131.108.3.2 (10639872/128256), Serial0/0 via 131.108.10.2 (20640000/128256), Serial0/1 P 131.108.8.0/24, 1 successors, FD is 2297856 via 131.108.3.2 (10639872/128256), Serial0/0 via 131.108.10.2 (20640000/128256), Serial0/1 P 131.108.7.0/24, 1 successors, FD is 2297856 via 131.108.3.2 (10639872/128256), Serial0/0 via 131.108.10.2 (20640000/128256), Serial0/1 P 131.108.6.0/24, 1 successors, FD is 128256 via Connected, Loopback2 P 131.108.5.0/24, 1 successors, FD is 128256 via Connected, Loopback1 P 131.108.4.0/24, 1 successors, FD is 128256 via Connected, Loopback0 P 131.108.3.0/30, 1 successors, FD is 2169856 via Connected, Serial0/0 via 131.108.10.2 (21024000/1761792), Serial0/1 P 131.108.2.0/24, 1 successors, FD is 2195456 via 131.108.3.2 (10537472/281600), Serial0/0 via 131.108.10.2 (20537600/281600), Serial0/1 P 131.108.1.0/24, 1 successors, FD is 281600 via Connected, Ethernet0/0
- 89. 66 Chapter 2: General Networking Topics Example 2-17 shows that the remote network 131.108.2.0 is via two paths, and because the feasible distance is lower through Serial 0/0, that path is injected into the routing table. If, for some reason, the link with Serial 0/0 on R1 fails, the alternate path will be chosen and inserted into the routing table, increasing convergence times. When EIGRP loses a path to a remote network, it sends requests to neighboring routers for alternative ways to reach the failed network. The neighboring router that returns the most favorable routes is called the feasible successor; in Figure 2-15, that router is R2. NOTE The Cisco CD Documentation Codes State of this topology table entry are defined as follows: • P (Passive)—No EIGRP computations are being performed for this destination. • A (Active)—EIGRP computations are being performed for this destination. • U (Update)—Indicates that an update packet was sent to this destination. • Q (Query)—Indicates that a query packet was sent to this destination. • R (Reply)—Indicates that a reply packet was sent to this destination. • r (Reply status)—–A flag that is set after the software has sent a query and is waiting for a reply. *Cisco Connection online was the source for this material, www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fiprrp_r/1rfeigrp.htm#1 025659. OSPF OSPF is a link-state routing protocol. Link-state protocols use Dijkstra’s shortest path first (SPF) algorithm to populate the routing table. OSPF shares information with every router in the network. OSPF is a classless protocol and supports VLSM. Table 2-11 defines common OSPF terminology. OSPF in a Single Area When configuring any OSPF router, you must establish what area assignment the interface will be enabled for. OSPF has some basic rules when it comes to area assignment. OSPF must be configured with areas. The backbone area 0, or 0.0.0.0, must be configured if you use more than one area assignment. If your OSPF design has only one area, it can have any number.
- 90. Routing Protocols 67 Table 2-11 Common OSPF Terms Term Description Hello packet Exchanged by the routers for neighbor discovery and forming adjacency, neighbor keep-alive, and DR/BDR election. Link state Information is shared between directly connected routers. This information propagates unchanged throughout the network and is also used to create a shortest path first (SPF) tree. Area A group of routers and links that share the same Area ID. All OSPF routers require area assignments. All routers within an area have the same database. Link state flooding is limited to an area. Autonomous system (AS) A network under a common network administration domain running common routing protocols. Cost (OSPF Metric) The routing metric used by OSPF. Lower costs are always preferred. You can manually configure the cost of an interface with the ip ospf cost command. By default, the cost is calculated by using the formula, cost = 108/bandwidth. Router ID Each OSPF router requires a unique router ID, which is the highest IP address configured on a Cisco router or the highest-numbered loopback address. You can manually assign the router ID. Adjacency When two OSPF routers have exchanged information between each other and have the same topology table. Adjacency can have a number of states or exchange states: Init state—When Hello packets have been sent and are awaiting a reply to establish two-way communication. Establish bidirectional (two-way) communication—Accomplished by the discovery of the Hello protocol routers and the election of a DR. Exstart—Two neighbor routers form a master/slave relationship and agree upon a starting sequence that will be incremented to ensure that LSAs are acknowledged. Exchange state—Database Description (DD) packets continue to flow as the slave router acknowledges the master’s packets. OSPF is operational because the routers can send and receive LSAs between each other. DD packets contain information such as the router ID, area ID, checksum, if authentication is used, link-state type, and the advertising router. LSA packets also contain information such as router ID, and additionally include MTU sizes, DD sequence numbering, and any options. continues
- 91. 68 Chapter 2: General Networking Topics Table 2-11 Common OSPF Terms (Continued) Term Description Adjacency (Continued) Loading state—Link-state requests are sent to neighbors asking for recent advertisements that have been discovered in Exchange state but not received. Full state—Neighbor routers are fully adjacent because their link-state databases are fully synchronized within the area. Routing tables begin to be populated. Topology table Also called the link-state table, this table contains every link in the entire network. Designated Router (DR) This router ensures adjacencies between all neighbors on a multiaccess network (such as Ethernet). This ensures that not all routers need to maintain full adjacencies with each other. The DR is selected based on the priority. In a tie, the router with the highest router ID is selected. Backup DR A Backup Designated Router is designed to perform the same functions in case the DR fails. Link-state advertisement A packet that contains all relevant information regarding a router’s links (LSA) and the state of those links. Priority Sets the router’s priority so a DR or BDR can be correctly elected. Router links Describe the state and cost of the router’s interfaces to the area. Router links use LSA type 1. Summary links Originated by Area Border Routers, these links describe networks in the AS. Summary links use LSA type 3 and 4. Network links Originated by DRs. Network links use LSA type 2. External links Originated by autonomous system boundary routers; they advertise destinations external to the AS or the default route external to the AS. Area Border Router Router located on the border of one or more OSPF areas to connect those (ABR) areas to the backbone network. Autonomous system An ABR located between an OSPF autonomous system and a non-OSPF boundary router (ASBR) network. The configuration steps to enable OSPF in a single area are as follows: Step 1 Start OSPF with the command router ospf process ID. The process ID is locally significant to the router. Step 2 Enable the interfaces with the network command. For example, to place the Net- work 131.108.1.0 in area 1, the IOS command is network 131.108.1.0 area 1.
- 92. Routing Protocols 69 Step 3 Identify area assignments. Step 4 (Optional) Assign the router ID with the router-id router-id IOS command under the OSPF process. NOTE The following is a list of reasons OSPF (link-state) is considered a better routing protocol than RIPv1 (distance vector): • OSPF has no hop count limitation. (RIP has a limit of 15 hops only.) • OSPF understands VLSM and allows for summarization. • OSPF uses multicasts (not broadcasts) to send updates. • OSPF converges much faster than RIP because OSPF propagates changes immediately. OSPF is faster because it sends the link update and then calculates the local routing table. RIP calculates the local routing table and then sends an update. • OSPF allows for load balancing with up to six equal-cost paths. • OSPF has authentication available (RIPv2 does also, but RIPv1 does not). • OSPF allows tagging of external routes injected by other autonomous systems. • OSPF configuration, monitoring, and troubleshooting have a far greater IOS tool base than RIP. Multiple OSPF Areas An OSPF area is a logical grouping of routers and links by a network administrator. OSPF routers in any area share the same topological view (also known as the OSPF or database) of the network. OSPF is configured in multiple areas to reduce routing table sizes, which in return, reduces the topological database and CPU/memory requirements on a router. Routing tables become very large even with just 50 routers. Cisco recommends no more than 50 routers per area. The OSPF database is exchanged in full every 30 minutes, and if this database is too large, every time this occurs, the amount of bandwidth used over the network increases and can cause severe delays in sending user-based traffic because convergence times are increased. Areas allow OSPF designers to limit and confine changes. Additionally, a number of predefined areas types help reduce the demand on routers, as displayed in Table 2-12.
- 93. 70 Chapter 2: General Networking Topics Table 2-12 Additional Area Types Area Type Function Stubby area This area does not accept LSA types 4 and 5, which are summary links and external link advertisements, respectively. The only way to achieve a route to unknown destinations is a default route injected by the ABR. Totally stubby area This area blocks LSA types 3, 4, and 5. Only a single type 3 LSA advertising the default route is allowed. This solution is Cisco proprietary and is used to further reduce a topological database. Not-so-stubby area This area is used primarily for connections to an ISP. This area is designed to (NSSA) allow type 7 LSAs only. All advertised routes can be flooded through the NSSA but are blocked by the ABR. Basically, a type 7 LSA (if the P bit is set to one) is converted to a type 5 LSA and flooded through the rest of the network. If the P bit is set to 0, no translation will take place. Type 4 or 5 LSAs are not permitted. This advertisement will not be propagated to the rest of the network. NSSAs typically provide a default route. Table 2-13 defines the challenges across various media types, such as Frame Relay and broadcast media. Table 2-13 OSPF over Various Media Types Using Cisco IOS Software Method Description Point-to-point nonbroadcast Used typically for Frame Relay interfaces. Point-to-point This is the default mode for subinterfaces. Point-to-multipoint Used for multiple destinations. Nonbroadcast Nonbroadcast multiaccess (NBMA) mode. Broadcast Used in Ethernet and broadcast environments where the election of DR/BDR takes place. To define the DR, use the IOS command ip ospf priority priority-number. The priority-number is 1 to 255. The highest priority will be to elect the DR. Ethernet is an example of where OSPF will elect a DR to minimize the OSPF updates over a broadcast medium. Each multiaccess OSPF network that has at least two attached routers has a designated router elected by the OSPF Hello protocol. The DR enables a reduction in the number of adjacencies required on a multiaccess network, which reduces the amount of routing protocol traffic and the size of the topological database, especially when more than two routers are deployed on this network segment.
- 94. Routing Protocols 71 Virtual Links All OSPF areas must be connected to the backbone area (Area 0). Figure 2-16 demonstrates a topology where an area (Area 100) is not directly connected to the backbone. Figure 2-16 OSPF Area Assignment Virtual Link or New WAN circuit required Transit Area (200) Router A Router B Router C Router D Router F Router E Area 0 Area 200 Area 100 or Backbone To ensure that Area 100 is reachable by the backbone, a virtual link can be configured over the transit area (200), and IP connectivity will be maintained. Virtual links are typically used in a transition phase (for example, when one company buys another and both companies use OSPF). Another solution to the problem depicted in Figure 2-16 is to install a physical link between Router C or Router D and the backbone core network. OSPF Configuration Example Figure 2-17 demonstrates a two-router topology. Figure 2-17 displays three OSPF areas with Area 2 partitioned from the backbone, necessitating a virtual link.
- 95. 72 Chapter 2: General Networking Topics Figure 2-17 Typical Cisco IOS OSPF topology Virtual Link Required Transit Area Area 0 Area 1 Area 2 131.108.225.0/30 Frame Relay 131.108.1.1/24 S0/0 S0/0 172.108.2.1/24 .1 .2 PVC#1 PVC#2 E0/0 F/R E0/0 R1 S0/1 S0/1 R2 .5 .6 131.108.255.4/3 0 Frame Relay Point-to-point network 256 Kb for each PVC R1's Loopbacks in Area 0 R2's Loopbacks in Area 1 Loopback0 131.108.2.1/24 Loopback0 131.108.9.1/24 Loopback1 131.108.3.1/24 Loopback1 131.108.10.1/24 Loopback2 131.108.4.1/24 Loopback2 131.108.11.1/24 Loopback3 131.108.5.1/24 Loopback3 131.108.12.1/24 Loopback4 131.108.6.1/24 Loopback4 131.108.13.1/24 Loopback5 131.108.7.1/24 Loopback5 131.108.14.1/24 Loopback6 131.108.15.1/24 Example 2-18 displays the full working configuration of R1. Example 2-18 R1’s OSPF Configuration ! hostname R1 enable password cisco interface Loopback0 ip address 131.108.2.1 255.255.255.0 ip ospf network point-to-point ! interface Loopback1 ip address 131.108.3.1 255.255.255.0 ip ospf network point-to-point ! interface Loopback2 ip address 131.108.4.1 255.255.255.0 ip ospf network point-to-point
- 96. Routing Protocols 73 Example 2-18 R1’s OSPF Configuration (Continued) ! interface Loopback3 ip address 131.108.3.1 255.255.255.0 ip ospf network point-to-point ! interface Loopback4 ip address 131.108.6.1 255.255.255.0 ip ospf network point-to-point ! interface Loopback5 ip address 131.108.7.1 255.255.255.0 ip ospf network point-to-point ! interface Ethernet0/0 ip address 131.108.1.1 255.255.255.0 ! interface Serial0/0 bandwidth 256 ip address 131.108.255.1 255.255.255.252 encapsulation frame-relay ip ospf network point-to-point ! interface Serial0/1 bandwidth 256 ip address 131.108.255.5 255.255.255.252 encapsulation frame-relay ip ospf network point-to-point ! router ospf 1 router-id 131.108.7.1 area 1 virtual-link 131.108.15.1 network 131.108.0.0 0.0.7.255 area 0 network 131.108.255.0 0.0.0.3 area 0 network 131.108.255.4 0.0.0.3 area 0 ! end By default, loopback interfaces are stub hosts in OSPF and are advertised as 32-bit hosts. The IOS command ip ospf network point-to-point advertises the loopback networks as /24 networks (in this case, you use /24 subnet mask). The Frame Relay connection is configured as point-to-point to ensure that no manual OSPF neighbor configuration is required to form OSPF neighbors. The virtual link is configured across the transit area, 1, to R2 router ID of 131.108.14.1.
- 97. 74 Chapter 2: General Networking Topics Example 2-19 displays R2’s full working configuration. Example 2-19 R2’s OSPF Configurations hostname R2 enable password cisco interface Loopback0 ip address 131.108.9.1 255.255.255.0 ip ospf network point-to-point ! interface Loopback1 ip address 131.108.10.1 255.255.255.0 ip ospf network point-to-point ! interface Loopback2 ip address 131.108.11.1 255.255.255.0 ip ospf network point-to-point ! interface Loopback3 ip address 131.108.12.1 255.255.255.0 ip ospf network point-to-point ! interface Loopback4 ip address 131.108.13.1 255.255.255.0 ip ospf network point-to-point ! interface Loopback5 ip address 131.108.14.1 255.255.255.0 ip ospf network point-to-point ! interface Loopback6 ip address 131.108.15.1 255.255.255.0 ip ospf network point-to-point ! interface Ethernet0/0 ip address 131.108.8.1 255.255.255.0 half-duplex ! interface Serial0/0 ip address 131.108.255.2 255.255.255.252 encapsulation frame-relay ip ospf network point-to-point interface Serial0/1 ip address 131.108.255.6 255.255.255.252 encapsulation frame-relay ip ospf network point-to-point ! router ospf 1 router-id 131.108.15.1 area 1 virtual-link 131.108.7.1 network 131.108.8.0 0.0.0.255 area 2 network 131.108.9.0 0.0.0.255 area 1
- 98. Routing Protocols 75 Example 2-19 R2’s OSPF Configurations (Continued) network 131.108.10.0 0.0.0.255 area 1 network 131.108.11.0 0.0.0.255 area 1 network 131.108.12.0 0.0.0.255 area 1 network 131.108.13.0 0.0.0.255 area 1 network 131.108.14.0 0.0.0.255 area 1 network 131.108.15.0 0.0.0.255 area 1 network 131.108.255.0 0.0.0.3 area 0 network 131.108.255.4 0.0.0.3 area 0 end Example 2-20 displays the IP OSPF routing table on R1. Example 2-20 show ip route ospf on R1 R1#show ip route ospf 131.108.0.0/16 is variably subnetted, 17 subnets, 2 masks O 131.108.15.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1 [110/391] via 131.108.255.2, 00:00:41, Serial0/0 O 131.108.14.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1 [110/391] via 131.108.255.2, 00:00:41, Serial0/0 O 131.108.13.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1 [110/391] via 131.108.255.2, 00:00:41, Serial0/0 O 131.108.12.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1 [110/391] via 131.108.255.2, 00:00:41, Serial0/0 O 131.108.11.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1 [110/391] via 131.108.255.2, 00:00:41, Serial0/0 O 131.108.10.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1 [110/391] via 131.108.255.2, 00:00:41, Serial0/0 O 131.108.9.0/24 [110/391] via 131.108.255.6, 00:00:41, Serial0/1 [110/391] via 131.108.255.2, 00:00:42, Serial0/0 O IA 131.108.8.0/24 [110/400] via 131.108.255.6, 00:00:42, Serial0/1 [110/400] via 131.108.255.2, 00:00:42, Serial0/0 R1’s routing table has the remote OSPF networks labeled as O IA because the network 131.108.8.0/24 is part of an area not directly attached to R1. Also, R1 is automatically load balancing across the two paths because the cost metric is the same (391). The administrative distance is 110 (the default). NOTE The election of the designated router in networks such as Frame Relay is important, and you must ensure the hub or core network router is the elected DR so that the hub router disseminates information to all spoke routers. To ensure the hub is the DR, you can disable the DR election process on edge routers with the IOS command, ip ospf priority 0.
- 99. 76 Chapter 2: General Networking Topics Border Gateway Protocol Border Gateway Protocol (BGP) is an exterior routing protocol used widely in the Internet. It is commonly referred to as BGP4 (version 4). BGP4 is defined in RFC 1771. BGP allows you to create an IP network free of routing loops between different autonomous systems. An autonomous system (AS) is a set of routers under the same administrative control. BGP is called a path vector protocol because it carries a sequence of AS numbers that indicates the path taken to a remote network. This information is stored so that routing loops can be avoided. BGP uses TCP as its Layer 4 protocol (TCP port 179). No other routing protocol in use today relies on TCP. This allows BGP to make sure that updates are sent reliably, leaving the routing protocol to concentrate on gathering information about remote networks and ensuring a loop- free topology. Routers configured for BGP are typically called BGP speakers, and any two BGP routers that form a BGP TCP session are called BGP peers or BGP neighbors. BGP peers initially exchange full BGP routing tables. After the exchange, only BGP updates are sent between peers, ensuring that only useful data is sent unless a change occurs. Four message are types used in BGP4 to ensure that peers are active and updates are sent: • Open Messages—Used when establishing BGP peers. • Keepalives—These messages are sent periodically to ensure connections are still active or established. • Update messages—Any changes that occur, such as a loss of network availability, result in an update message. • Notification—Only used to notify BGP peers of any receiving errors. Key BGP characteristics include the following: • BGP is a path vector protocol. • BGP uses TCP as the transport layer protocol. • Full routing table is exchanged only during initial BGP session. • Updates are sent over TCP port 179. • BGP sessions are maintained by keepalive messages. • Any network changes result in update messages. • BGP has its own BGP table. Any network entry must reside in the BGP table first. • BGP has a complex array of metrics, such as next-hop address and origin, which are called attributes. • BGP supports VLSM and summarization (sometimes called Classless Interdomain Routing [CIDR]).
- 100. Routing Protocols 77 BGP4’s ability to guarantee routing delivery and the complexity of the routing decision process mean that BGP will be widely used in any large IP routing environment, such as the Internet. The Internet consists of over 100,000 BGP network entries, and BGP is the only routing protocol available today that can handle and manage such a large routing table. The Internet (80,000+ routes) could not be functional today if BGP were not the routing protocol in use. Before covering some simple examples, the next section describes BGP attributes. BGP Attributes BGP has a number of complex attributes that determine a path to a remote network. These attributes allow a greater flexibility and complex routing decision to ensure a path to a remote network is taken by the best path possible. The network designer can also manipulate these attributes. BGP, when supplied with multiple paths to a remote network, will always choose a single path to a specific destination. (Load balancing is possible with static routes.) BGP always propagates the best path to any peers. BGP attributes are carried in update packets. Table 2-14 describes the well-known and optional attributes used in BGP4. Table 2-14 Well-Known and Optional Attributes Attribute Description Origin This attribute is mandatory, defines the source of the path, and can be three different values: IGP—Originating from interior of the AS. EGP—Learned through an External Gateway Protocol. Incomplete—The BGP route was discovered using redistribution or static routers. AS_Path Describes the sequences of AS that the packet has traversed to the destination IP network. Next Hop Describes the next-hop address taken to a remote path, typically the eBGP peer. Local Preference Indicates the preferred path to exit the AS. A higher local preference is always preferred. Multi Exit Discriminator (MED) Informs BGP peers in other autonomous systems about which path to take into the AS when multiple autonomous systems are connected. A lower MED is always preferred. continues
- 101. 78 Chapter 2: General Networking Topics Table 2-14 Well-Known and Optional Attributes (Continued) Attribute Description Weight Cisco-defined, attribute-only attribute that is used in local router selection. Weight is not sent to other BGP peers, and higher weight value is always preferred. Weight is locally significant to the router and specifies a preferred path when more than one path exists. Cisco-only attribute. Atomic Aggregate Advises BGP routers that aggregation has taken place. Not used in router selection process. Aggregator The router ID responsible for aggregation; not used in the router selection process. Community Allows routes to be tagged and use a group of routes sharing the same characteristics. An ISP typically tags traffic from customers along with a route-map to modify the community attribute. Originator ID Prevents routing loops. This information is not used for router selection. Cluster-List Used in a route-reflectors environment. This information is not used for router selection. There are two types of BGP sessions: internal BGP (IBGP) and external BGP (EBGP). IBGP is a connection between two BGP speakers in the same AS. EBGP is a connection between two BGP speakers in different autonomous systems. IBGP peers also make sure that routing loops cannot occur by ensuring that any routes sent to another AS must be known via an interior routing protocol, such as OSPF, before sending that information. That is, the routers must be synchronized. The benefit of this added rule in IBGP TCP sessions is that information is not sent unless it is reachable, which reduces any unnec- essary traffic and saves bandwidth. Route reflectors in IBGP ensure that large internal BGP networks do not require a fully meshed topology. Route reflectors are not used in EBGP con- nection. A BGP route reflector disseminates routing information to all route-reflector clients, and ensures that BGP tables are sent and that a fully meshed IBGP need not be configured. The BGP routing decision is quite complex and takes several attributes into account. The attributes and process taken by a Cisco router running BGP4 are as follows: 1 If the next-hop address is reachable, consider it. 2 Prefer the route with the highest weight (Cisco IOS routers only). 3 If the weight is the same, prefer the largest local preference attribute. 4 If the local preference is the same, prefer the route originated by this local router (routes generated by network or redistribute commands).
- 102. ISDN 79 5 Then prefer the route with the shortest AS Path. 6 If this is equal, prefer the route with origin set to originated (via BGP); IGP is preferred to EGP and then incomplete. 7 If the origin codes are the same, prefer the route with the lowest MED. 8 If the MED is the same, prefer EBGP over IBGP. 9 Then prefer the path that is the closest. 10 Finally, if all else is equal, prefer the path with the lowest BGP router ID. Configuring BGP To start the BGP process on a Cisco router requires the following command: router bgp autonomous-system-number To define networks to be advertised, apply the following command: network network-number mask network-mask You must be aware that the network command is not used the same way you apply networks in OSPF or EIGRP. With BGP, the network command advertises networks that are originated from the router and should be advertised via BGP. For more Cisco IOS examples of BGP, please visit Chapter 9, “CCIE Security Self-Study Lab.” To identify peer routers, apply the following command: neighbor {ip-address | peer-group name} remote-as autonomous-system-number NOTE Route redistribution allows routing information discovered through one routing protocol to be distributed in the update messages of another routing protocol. Whenever redistribution is configured on Cisco routers, the routing metric must also be converted. For example, with redistribution from a RIP domain into OSPF, the RIP network inserted into OSPF requires an OSPF cost metric. ISDN Integrated Services Digital Network (ISDN) is a digital service that enables network users to send and receive data, voice, and video transmissions over a network. ISDN offers a variety of link speeds, ranging from 64 kbps to 2.048 Mbps. Many small- and medium-sized companies find that ISDN is a viable network solution.
- 103. 80 Chapter 2: General Networking Topics Basic Rate and Primary Rate Interfaces ISDN can be supplied by a carrier in two main forms: Basic Rate Interface (BRI) and Primary Rate Interface (PRI). An ISDN BRI consists of two 64-kbps services (B channels) and one 16-kbps signaling channel (D channel). An ISDN PRI consists of 23 B or 30 B channels, depending on the country. In North America and Japan, a PRI service consists of 23 B channels. In Europe and Australia, a PRI service consists of 30 B channels. A signaling channel (or D channel) is used in a PRI service and is a dedicated 64-kbps channel. The B channel sends data and the D channel primarily controls signaling. NOTE The effective throughput of a PRI service with 23 channels is 1.472 Mbps (23 × 64 kbps). With 30 B channels, the effective throughput is 1.920 Mbps (30 × 64 kbps). The International Telecommunications Union (ITU) defines the standards for ISDN. The specified standard is ITU-T Q.921. ISDN Framing and Frame Format The ISDN physical layer provides the ability to send outbound traffic and receive inbound traffic by transmitting binary bits over the physical media. The ISDN data link layer provides signaling, which ensures that data is sent and received correctly. The signaling protocol used in ISDN is called the Link Access Procedure on the D channel (LAPD). ISDN Layer 2 Protocols ISDN can use a number of Layer 2 encapsulation types. Point-to-Point Protocol (PPP) and high-level data link control (HDLC) are the only methods tested in the qualification exam. NOTE X.25 is not tested in the CCIE Security written exam. HDLC High-level data link control is a WAN protocol encapsulation method that allows point-to-point connections between two remote sites. Typically, HDLC is used in a leased-line setup. HDLC is a connectionless protocol that relies on upper layers to recover any frames that have encoun- tered errors across a WAN link. HDLC is the default encapsulation on Cisco serial interfaces. Cisco routers use HDLC encapsulation, which is proprietary. Cisco added an address field in the HDLC frame, which is not present in the HDLC standard. This field is used by Cisco devices to indicate the type of payload (protocol). Cisco routers use the address field in an
- 104. ISDN 81 HDLC frame to indicate a payload type, but other routers or manufacturers that implement the HDLC standard do not use the address field. HDLC cannot be used to connect a Cisco router with another vendor. Figure 2-18 displays the HDLC frame format, which shares a common format with the PPP frame format discussed in the next section. Figure 2-18 HDLC Frame Format Field Length in Bytes 1 2 1 2 Variable 1 1 Flag Address Control Protocol Data FCS Flag SAPI C/R EA TEI EA SAPI - Service Access Point Identifier C/R - Command/Response EA - Extended Address TEI - Terminal Endpoint Identifier (All 1s indicate a broadcast.) Point-to-Point Protocol (PPP) PPP was designed to transport user information between two WAN devices (also referred to as point-to-point links). PPP was designed as an improvement over Serial Line Internet Protocol (SLIP). When PPP encapsulation is configured on a Cisco WAN interface, the network administrator can carry protocols such as IP and IPX, as well as many others. Cisco routers support PPP over asynchronous lines, High-Speed Serial Interfaces (HSSIs), ISDN lines, and synchronous serial ports. PPP has the added function of allowing authentication to take place before any end user data is sent across the link. The following three phases occur in any PPP session: • Link establishment—Link Control Protocol (LCP) packets are sent to configure and test the link. • Authentication (optional)—After the link is established, authentication can ensure that link security is maintained. • Network layers—In this phase, Network Control Protocol (NCP) packets determine which protocols are used across the PPP link. An interesting aspect of PPP is that each protocol (IP, IPX, and so on) supported in this phase is documented in a separate RFC that discusses how it operates over PPP.
- 105. 82 Chapter 2: General Networking Topics Figure 2-19 displays the PPP frame format, which is similar to the HDLC frame format in Figure 2-18. Figure 2-19 PPP Frame Format Field Length in Bytes 1 1 1 1 Variable 2 or 4 Flag Address Control Protocol Data FCS 01111110 11111111 Address Identifies Frame not used. Payload Check Sequence Set to all 1s. LCP LPC is used to establish, configure, and test the link between two devices, such as Cisco routers. LCP provides the necessary negotiations between end devices to activate the link. After the link is activated, but while no data is yet flowing, the next phase(s) of the PPP session can take place—authentication (if configured) and the NCP. Authentication PPP supports authentication through Password Authentication Protocol (PAP) and Challenge Handshake Authentication Protocol (CHAP), with CHAP providing a more secure method of authentication. CHAP passwords are encrypted and safe from intruders because they are never actually transmitted on the wire. This technique, known as shared secrets, means that both devices know the secret (password), but they never talk about it directly. PAP passwords are sent in clear text; they are clearly visible on the wire. NCP PPP uses NCP packets to allow multiple network layer protocol types to transfer across WANs from point to point. IP Control Program (IPCP) allows IP connectivity, and IPXCP allows IPX connectivity. Cisco IOS ISDN Commands Cisco routers support ISDN. The commands most often used to enable data and voice communications over ISDN are listed in Table 2-15.
- 106. IP Multicast 83 Table 2-15 ISDN Commands IOS Command Description isdn caller phone-number The number called by the router. The phone-number is the remote router’s ISDN number. isdn calling-number calling-number The number of the device making the outgoing call; only one entry is allowed. isdn switch-type ISDN service provider switch type. NOTE Frame Relay is a Layer 2 protocol that provides connectionless delivery between devices. Frame Relay, although not listed in the official blueprint for the CCIE Security written exam, has a few terms you should be aware of for the exam: • Forward explicit congestion notification (FECN)—A bit set by a Frame Relay network to inform DTE receiving the frame that congestion was experienced in the path from source to destination. DTE receiving frames with the FECN bit set can request that higher-level protocols take flow-control action, as appropriate. • Backward explicit congestion notification (BECN)—A bit set by a Frame Relay net- work in frames traveling in the opposite direction of frames encountering a congested path. DTE receiving frames with the BECN bit set can request that higher-level protocols take flow-control action, as appropriate. The ISP or WAN switches typically set FECN/BECN. • Data-link connection identifier (DLCI)—A value that specifies a PVC or SVC in a Frame Relay network. DLCIs are locally significant. Globally significant DLCIs are used for LMI communication between Frame Relay switches. IP Multicast This section briefly covers the IP multicast areas of interest for the CCIE written test. The multicasting protocol was designed to reduce the high bandwidth requirements of technologies, such as video on demand, to a single stream of information to more than one device. Applications include electronic learning, company share meetings (video on demand), and software distribution. Multicasting can be defined as unicast (one to one), multicast (one to many), and broadcast (one to all). Multicasting transmits IP packets from a single source to multiple destinations. The network copies single packets, which are sent to a subset of network devices. In IPv4, the Class D addresses ranging from 224.0.0.0 to 239.255.255.255 are reserved for multicast. Routing protocols, for example, use multicasting to send hello packets and establish neighbor adjacencies.
- 107. 84 Chapter 2: General Networking Topics Table 2-16 displays some common multicast addresses and their uses. Table 2-16 Class D Multicast Address Examples Multicast Address Use 224.0.0.1 All hosts on subnets 224.0.0.2 All multicast routers 224.0.0.5 All OSPF-enabled routers 224.0.0.6 All OSPF DR routers 224.0.0.9 RIPv2-enabled routers 224.0.0.10 All EIGRP-enabled routers TIP The Class D addresses used in multicast traffic range from 224.0.0.0 to 239.255.255.255. Asynchronous Communications and Access Devices An asynchronous (async) communication is a digital signal that is transmitted without precise clocking. The RS-232 session between a router and PC through the console connection is an example of async communications. Such signals generally have different frequencies and phase relationships. Asynchronous transmissions usually encapsulate individual characters in control bits (called start and stop bits) that designate the beginning and the end of each character. For example, the auxiliary port on Cisco routers can be used to connect a modem and allow out of band (not via the network) management. The Cisco AS5300 is an example of a device that supports both synchronous and async com- munication, such as voice, digital, and modem-based traffic (via a Public Switch Telephone Network [PSTN]). The AS5300, or universal Access Server (AS), is a versatile data communications platform that provides the functions of an access server, router, and digital modem in a single modular chassis. The access server is intended for ISPs, telecommunications carriers, and other service providers that offer managed Internet connections. The AS5300 provides both digital (for example, ISDN) and analog access (dialup users using PSTN) to users on a network. Figure 2-20 displays a typical scenario where clients, such as Internet dialup users with ISDN and analog phone lines (PSTN), can connect to the Internet using PPP. Clients are supplied one number to call, and the AS5300 makes intelligent decisions based on the incoming call type, whether it be digital (ISDN) or analog (PSTN).
- 108. Asynchronous Communications and Access Devices 85 Figure 2-20 AS5300 Typical Design Scenario WWW AS1 1.1.1.1/24 AS2 1.1.1.2/24 AS3 1.1.1.3/24 AS4 1.1.1.4/24 AS5300 ASI SGBP configuration Hostname ASI ! ISDN/PSTN PSTN PSTN ISDN ISDN username CCIE password CCIE calls come in using sgbp group CCIE PPP encapsullation. sgbp member AS2 1.1.1.2 sgbp member AS3 1.1.1.3 sgbp member AS4 1.1.1.4 ISDN Call ISDN Call PSTN Call PSTN Call Users, such as clients with ISDN, call the dedicated number supplied by the ISP. The four AS5300s in Figure 2-20 can also share the load of incoming calls using Stack Group Bidding Protocol (SGBP), which is used when multiple PPP, or multilink PPP (MPPP), sessions are in use. When SGBP is configured on each Cisco AS5300, each access server sends a query to each stack group member. A stack group member is a router running the SGBP protocol. Each router participating in SGBP then bids for the right to terminate the call. The router with an existing PPP session, for example, will win the bid; this allows the best bandwidth allocation to the end client, as both PPP sessions are terminated on the same router. If the PPP call is the first session to be terminated on the AS5300, the AS5300 with the lowest CPU usage will have a higher probability of terminating the call. Example 2-21 displays a typical IOS configuration when SGBP is enabled on the four AS5300 routers in Figure 2-21.
- 109. 86 Chapter 2: General Networking Topics Example 2-21 SGBP Configuration Example Hostname AS1 ! username CCIE password CCIE sgbp group CCIE sgbp member AS2 1.1.1.2 sgbp member AS3 1.1.1.3 sgbp member AS4 1.1.1.4 The following list explains the IOS commands used in Example 2-21. • username CCIE password CCIE—Defines the username and password used for authenticating SGBP members. If the password is wrong, an error such as the following is presented on the console: %SGBP-1-AUTHFAILED: Member [chars] failed authentication • sgbp group CCIE—Defines a named stack group and makes this router a member of that stack group. Use the sgbp group command in global configuration mode. To remove the definition, use the no form of this command. • sgbp member ip-address—Specifies the host name and IP address of a router or access server that is a peer member of a stack group. Use the sgbp member command in global configuration mode.
- 110. Foundation Summary 87 Foundation Summary The “Foundation Summary” is a condensed collection of material for a convenient review of key concepts in this chapter. If you are already comfortable with the topics in this chapter and decided to skip most of the “Foundation Topics” material, the “Foundation Summary” will help you recall a few details. If you just read the “Foundation Topics” section, this review should help further solidify some key facts. If you are doing your final preparation before the exam, the “Foundation Summary” offers a convenient and quick final review. Table 2-17 OSI Model OSI Name and Layer Number Description Application layer (Layer 7) The application layer is closest to the end user, which means that the application is being accessed by the end user. This layer’s major function is to provide services to end users. Examples of application layer services include the following: File Transfer Protocol (FTP) Telnet Ping Trace route SMTP Mail clients Presentation layer (Layer 6) The Presentation layer handles data formats and code formatting. This layer’s functions are normally transparent to the end user because it takes care of code formats and presents them to the application layer (Layer 7), where the end user can examine the data. Examples of presentation layer protocols include the following: GIF JPEG ASCII MPEG TIFF MIDI HTML Session layer (Layer 5) The session layer performs several major functions, including managing sessions between devices and establishing and maintaining sessions. Examples of session layer protocols include the following: Database SQL NetBIOS Name Queries H.323 Real Time Control Protocol continues
- 111. 88 Chapter 2: General Networking Topics Table 2-17 OSI Model (Continued) OSI Name and Layer Number Description Transport layer (Layer 4) The transport layer is responsible for segmenting upper-layer applica- tions and establishing end-to-end connections between devices. Other transport layer functions include providing data reliability and error-free delivery mechanisms. Information being processed at this layer is com- monly known as segments. Examples of transport layer protocols include Transmission Control Protocol (TCP) and User Datagram Protocol (UDP). Network layer (Layer 3) The network layer determines the best path to a destination. Device addressing, packet fragmentation, and routing all occur at the network layer. Information being processed at this layer is commonly known as packets. Examples of network layer protocols include the following: Internet Protocol (IP) Open Shortest Path First (OSPF) Cisco’s EIGRP routing protocol Data Link layer (Layer 2) The data link layer focuses on getting data reliably across any particular kind of link. Flow control and error notifications are other data link layer functions. The data link layer applies to all access methods, whether they are LAN or WAN methods. Information being processed at this layer is commonly known as frames. Example include the following: ISDN SDLC HDLC PPP Frame Relay Spanning tree protocol NetBEUI Physical layer (Layer 1) The physical layer consists of standards that describe bit ordering, bit transmission rates, connector types, and electrical and other specifications. Information at Layer 1 is transmitted in binary (1s and 0s; for example, the letter A is transmitted as 00001010). Examples of physical layer standards include the following: RS-232 V.24 V.35 RJ-45 RJ-12 10BaseT 100BaseT 1000BaseT Gigabit Ethernet
- 112. Requirements for FastEther Channel 89 Table 2-18 Ethernet Media Formats Media Type Characteristics 10Base5 Maximum length 500 m. Maximum stations are 1024. Speed is 10 Mbps. Minimum distance between devices is 2.5 m. 10Base2 Maximum length 185 m, using RG58 cable types, T connectors on all end stations. Minimum distance between devices is 0.5 m. Maximum devices per 185 m segment is 30 stations. Speed is 10 Mbps. End points need termination. 10BaseT Based on UTP cabling. Up to 100 m (longer for better category cables). One device per cable. Typically only one device per segment with hubs or switches connecting all devices together. Speed is 10 Mbps. Physical topology is star, logical topology is liner. 100BaseT Same characteristics as 10baseT but operates faster, at 100 Mbps. Can be fibre, as well (100BaseFx). Defined in IEEE 802.3U. 1000 GE Gigabit Ethernet operating at 1000 Mbps. Can run over Fibre or UTP. Frame formats and CSMA/CD identical to Ethernet standards. Requirements for FastEther Channel • All ports part of FEC must be set to the same speed. • All ports must belong to the same VLAN. • Duplex must be the same (half or full), not a mixture. • Up to eight ports can be bundled together. • To set FastEther channel on a switch, the CatOS syntax is set port channel. • To set FastEther channel on a router, the IOS syntax is channel-group under the Fast Ethernet interface.
- 113. 90 Chapter 2: General Networking Topics Table 2-19 The States of Spanning Tree Bridge Port State Description Disabled The port is not participating in spanning tree and is not active. Listening The port has received data from the interface and will listen for frames. In this state, the bridge receives only data but does not forward any frames to the interface or to other ports. Learning In this state, the bridge still discards incoming frames. The source address associated with the port is added to the CAM table. BPDU are sent and received. Forwarding The port is fully operational; frames are sent and received. Blocking The port has been through the learning and listening states, and because this particular port is a dual path to the root bridge, the port is blocked to maintain a loop-free topology. Table 2-20 Class A, B, C, D, and E Ranges Class of Address Starting Bit Pattern Range Default Subnet Mask Class A 0xxxxxxx 1 to 126, 127* 255.0.0.0 Class B 10xxxxxx 128 to 191 255.255.0.0 Class C 110xxxxx 192 to 223 255.255.255.0 Class D (multicast) 1110xxxx 224 to 239 255.255.255.240 Class E 1111xxxx 240 to 255 Reserved * 127.0.0.0 is reserved for loopbacks. Other reserved addresses for private use as defined by RFC 1918 are as follows: 10.0.0.0-10.255.255.255 172.16.0.0-172.31.255.255 192.168.0.0-192.168.255.255 Table 2-21 Routing Protocol Classifications Routing Protocol Class IGRP Distance vector (classful) EIGRP Hybrid (classless) OSPF Link-state (classless) RIPv1 Distance vector (classful) RIPv2 Distance vector (classless) BGP Path vector (classless)
- 114. Requirements for FastEther Channel 91 Table 2-22 TCP Flags Summary Flag Description URG (U) Urgent—Informs the other station that urgent data is being carried. The receiver will decide what do with the data. ACK (A) Acknowledge—Indicates that the packet is an acknowledgment of received data, and the acknowledgment number is valid. PSH (P) Push—Informs the end station to send data to the application layer immediately. RST (R) Reset—Resets an existing connection. SYN (S) Synchronize—Initiates a connection, commonly known as established. FIN (F) Finished—Indicates that the sender is finished sending data and terminates the session. Table 2-23 TCP/IP Applications Application Description Address Resolution Protocol (ARP) ARP maps an IP address to a MAC address. Reverse Address Resolution Protocol (RARP) RARP determines a host’s IP address when the MAC address is known. Dynamic Host Configuration Protocol (DHCP) Dynamically provides IP addresses to TCP/IP hosts, subnet masks, and gateway addressing. Many other IP options can be assigned, as well. Hot Standby Router Protocol (HSRP) Redundancy gateway protocol, Cisco proprietary. Internet Control Message Protocol (ICMP) A network layer (Layer 3) Internet protocol that reports errors and provides other information relevant to IP packet processing. ICMP is fully documented in RFC 792. Telnet TCP/IP application layer protocol that enables remote management of TCP/IP hosts, such as routers or switches. File Transfer Protocol (FTP) TCP/IP application layer protocol that enables file transfer between TCP/IP hosts using a TCP, connection-orientated protocol. Trivial File Transfer Protocol (TFTP) TCP/IP application layer protocol that enables file transfers between TCP/IP hosts using a UDP, connectionless protocol.
- 115. 92 Chapter 2: General Networking Topics Table 2-24 Default Administrative Distances Route Source Default Distance Connected interface 0 Static route 1 Enhanced IGRP summary route 5 External BGP 20 Internal enhanced IGRP 90 IGRP 100 OSPF 110 IS-IS 115 RIP 120 EGP 140 EIGRP external route 170 Internal BGP 200 Unknown 255
- 116. Q&A 93 Q&A The Q & A questions are designed to help you assess your readiness for the topics covered on the CCIE Security written exam and those topics presented in this chapter. This format helps you assess your retention of the material. A strong understanding of the answers to these questions will help you on the CCIE Security written exam. You can also look over the questions at the beginning of the chapter again for further review. As an additional study aid, use the CD-ROM provided with this book to take simulated exams, which draw from a database of over 300 multiple-choice questions—all different from those presented in the book. Select the best answer. Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.” 1 What are the seven layers of the OSI model? 2 What layer of the OSI model is responsible for ensuring that IP packets are routed from one location to another? 3 What mechanism is used in Ethernet to guarantee packet delivery over the wire? 4 Name two physical characteristics of 10BaseT?
- 117. 94 Chapter 2: General Networking Topics 5 What Catalyst command displays the bridging or CAM table on a Cisco 5000 series switch? 6 What are the possible states of spanning tree? 7 FastEther Channel (FEC) allows what to occur between Cisco Catalyst switches? 8 What field in the IP packet guarantees data delivery? 9 Name some examples of connection-orientated protocols used in TCP/IP networks. 10 Given the address, 131.108.1.56/24, what are the subnet and broadcast addresses? How many hosts can reside on this network? 11 How many hosts can reside when the subnet mask applied to the network 131.108.1.0 is 255.255.255.128 (or 131.108.1.0/25)?
- 118. Q&A 95 12 Name five routing protocols that support VLSM. 13 What is the destination port number used in a Telnet session? 14 What TCP/IP services are common in today’s large IP networks? 15 What IOS command displays the IP ARP table on a Cisco IOS router? 16 Cisco routers use what mechanism to determine the routing selection policy for remote networks if more than one routing protocol is running? 17 What is the administrative distance for OSPF, RIP, and external EIGRP? 18 Name five characteristics of distance vector routing protocols and provide two examples of routing protocols classified as distance vector.
- 119. 96 Chapter 2: General Networking Topics 19 IP RIP runs over what protocol and port number when sending packets to neighboring routers? 20 How many networks can be contained in an IP RIP update? 21 Specify three main differences between RIPv1 and RIPv2? 22 What is an EIGRP Feasible Successor? 23 What is the metric used by OSPF? 24 If OSPF is configured for one area, what area assignment should be used? 25 What LSA types are not sent in a total stubby area?
- 120. Q&A 97 26 What IOS command disables an interface from participating in the election of an OSPF DR/BDR router? 27 On an Ethernet broadcast network, a DR suddenly reboots. When the router recovers and discovers neighboring OSPF routers, will it be the designated router once more? 28 What Layer 4 protocol does BGP use to guarantee routing updates, and what destination port number is used? 29 What are ISDN BRI and PRI? 30 What are the three phases that occur in any PPP session? 31 Define what BECN and FECN mean in a Frame Relay network?
- 121. 98 Chapter 2: General Networking Topics 32 Frame Relay DLCI values are used for what purpose? 33 What is the IP address range used in IP multicast networks? 34 What type of network environment typically uses an AS5300?
- 122. Scenario 2-1: Routing IP on Cisco Routers 99 Scenario Scenario 2-1: Routing IP on Cisco Routers Figure 2-21 displays a network with one Cisco router and two directly attached Ethernet interfaces. Use Figure 2-21 to answer the following questions. Figure 2-21 Scenario Diagram E0 IP address 1.1.1.100 E1 IP address 2.1.1.100 MAC address 3333.3333.3333 MAC address 4444.4444.4444 R1 Ethernet 0 Ethernet 1 PC1 PC2 IP address 1.1.1.1 IP address 2.1.1.1 MAC address 1111.1111.1111 MAC address 2222.2222.2222 1 In Figure 2-21, PC1 cannot communicate with PC2. What is the likely cause of the problem assuming that the router is configured correctly? a. Router R1 requires a routing protocol to route packets from Ethernet0 to Ethernet1. b. There is a problem with the IP address configuration on Router R1. c. The gateway address on PC1 is wrong. d. The gateway address on the router is wrong. 2 In Figure 2-21, what will be the ping response display when an exec user on Router R1 pings PC1’s IP address for the first time? Assume that all configurations are correct. a. !!!!! b. !!!!. c. ..... d. .!!!! e. .!!!!!
- 123. 100 Chapter 2: General Networking Topics 3 What IOS command was used to display the following output taken from Router R1? Protocol Address Age (min) Hardware Addr Type Interface Internet 1.1.1.100 - 333.3333.3333 ARPA Ethernet0 Internet 2.1.1.100 - 4444.4444.4444 ARPA Ethernet1 Internet 1.1.1.1 10 1111.1111.1111 ARPA Ethernet0 Internet 2.1.1.1 10 2222.2222.2222 ARPA Ethernet1 a. show ip arpa b. show ip arp c. show interface ethernet0 d. show interface ethernet1
- 124. Scenario 2-1 Answers: Routing IP on Cisco Routers 101 Scenario Answers Scenario 2-1 Answers: Routing IP on Cisco Routers 1 Answer: c. Cisco IOS routers will route between directly connected interfaces and, because PC1 cannot ping PC2 on another subnet, the PC1 gateway address must not be configured correctly. 2 Answer: d. The first request will fail because of the ARP broadcast. The subsequent pings (five in total: one for an ARP request and four successful replies) will reply successfully. 3 Answer: b. show ip arp displays the correct ARP address table for the devices in Figure 2-21.
- 125. Exam Topics in this Chapter 14 Domain Name System (DNS) 15 Trivial File Transfer Protocol (TFTP) 16 File Transfer Protocol (FTP) 17 Hypertext Transfer Protocol (HTTP) 18 Secure Socket Layer (SSL) 19 Simple Mail Transfer Protocol (SMTP) 20 Network Time Protocol (NTP) 21 Secure Shell (SSH) 22 Lightweight Directory Access Protocol (LDAP) 23 Active Directory
- 126. CHAPTER 3 Application Protocols This chapter covers some of today’s most widely used application protocols. This chapter covers the following topics: • Domain Name System (DNS)—Topics in this section include how DNS is configured on Cisco routers and what port numbers are used when delivered across an IP network. • Trivial File Transfer Protocol (TFTP)—This section covers TFTP’s common uses, particularly on Cisco IOS-enabled routers. The process used to copy files to and from TFTP server is described. • File Transfer Protocol (FTP)—This section covers FTP and the advanced mechanisms used in this connection-orientated protocol to ensure data delivery. • Other Application Topics—Included are Hypertext Transfer Protocol (HTTP), Secure Socket Layer (SSL), Simple Network Management Protocol (SNMP), Simple Mail Transfer Protocol (SMTP), Network Time Protocol (NTP), Secure Shell (SSH), Lightweight Directory Access Protocol, and Active Directory. These sections cover some of the common configurations and IOS commands on Cisco routers that enable these applications. NOTE SNMP, although not listed officially on the Cisco website, is a possible topic in the written examination. “Do I Know This Already?” Quiz The purpose of this assessment quiz is to help you determine how to spend your limited study time. If you can answer most or all these questions, you might want to skim the “Foundation Topics” section and return to it later as necessary. Review the “Foundation Summary” section and answer the questions at the end of the chapter to ensure that you have a strong grasp of the material covered. If you already intend to read the entire chapter, you do not necessarily need to answer these questions now. If you find these assessment questions difficult, read through the entire “Foundation Topics” section and review it until you feel comfortable with your ability to answer all these and the “Q & A” questions at the end of the chapter.
- 127. 104 Chapter 3: Application Protocols Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.” 1 RFC 1700 defines what well-known ports for DNS? a. TCP port 21 b. TCP port 23 c. UDP port 21 d. UDP port 53 e. TCP/UDP port 53 2 What supplies DNS security? a. A default username/password pairing b. A TFTP directory c. A filename d. A domain name e. None of the above 3 What IOS command will stop a Cisco router from querying a DNS server when an invalid IOS command is entered on the EXEC or PRIV prompt? a. no ip domain-lookup b. no ip dns-lookup c. no ip dns-queries d. no exec 4 What does the following Global IOS configuration line accomplish? ip host SimonisaCCIE 131.108.1.1 131.108.1.2 a. Defines the router name as SimonisaCCIE b. Defines a local host name, SimonisaCCIE, mapped to IP addresses 131.108.1.1 and 131.108.1.2 c. Configures the IOS router for remote routing entries 131.108.1.1 and 131.108.1.2 d. Not a valid IOS command e. Configures the local routers with the IP address 131.108.1.1 and 131.108.1.2 on boot up
- 128. “Do I Know This Already?” Quiz 105 5 TFTP uses what predefined UDP port number? a. 21 b. 22 c. 23 d. 53 e. 69 6 What IOS command will copy an IOS image from the current system flash to a TFTP server? a. copy tftp image: b. copy flash tftp c. copy tftp flash d. copy tftp tftp 7 Suppose a client calls and advises you that an FTP data transaction is not allowing him to view the host’s directory structure. What are the most likely causes of the problem? (Choose all that apply.) a. The client’s username/password is wrong. b. The client’s FTP data port is not connected. c. The host machine has denied him access because the password is wrong. d. A serious network outage requires that you reload the router closest to the client. e. An access list is stopping port 20 from detailing the directory list. 8 FTP runs over what Layer 4 protocol? a. IP b. TCP c. TFTP d. DNS e. UDP
- 129. 106 Chapter 3: Application Protocols 9 HTTPS traffic uses what TCP port number? a. 21 b. 443 c. 334 d. 333 e. 343 10 SNMP is restricted on Cisco routers by what IOS command? a. snmp-server enable b. snmp-server community string c. snmp-server ip-address d. snmp-server no access permitted 11 TFTP protocol uses which of the following? a. Username/password pairs to authorize transfers b. Uses TCP port 169 c. Uses UDP port 169 d. Can use UDP/TCP and port 69 e. None of the above 12 Which of the following statements is true regarding SSL? a. Every packet sent between host and client is authenticated. b. Encryption is used after a simple handshake is completed. c. SSL uses port 2246. d. SSL is not a predefined standard. e. SSL does not perform any data integrity checks. 13 What is the HELO SMTP command used for? a. To authenticate SMTP clients b. To identify SMTP clients c. This is an unknown standard d. The HELO command is used in SNMP (not SMTP)
- 130. “Do I Know This Already?” Quiz 107 14 POP3 clients can do what? a. Receive SNMP queries b. Send mail c. Send SNMP queries d. The POP3 protocol is a routing algorithm 15 NTP uses what well-known TCP port? a. 23 b. 551 c. 21 d. 20 e. 123 f. 321 16 Secure Shell (SSH) is used to do what? a. Disable spanning tree on Catalyst 5000 switches b. Protect the data link layer only from attacks c. Protect the TCP/IP host d. Allow TCP/IP access to all networks without any security e. SSH is used only in the data link layer 17 Which of the following protocols can be authenticated? (Select the best four answers.) a. Telnet b. HTTP c. HTTPS d. Spanning tree e. TFTP f. FTP
- 131. 108 Chapter 3: Application Protocols 18 What is the community string value when the following IOS commands are entered in global configuration mode? snmp-server community publiC RO snmp-server enable traps config snmp-server host 131.108.255.254 isdn a. ISDN b. Config c. publiC d. public e. Public f. More data required 19 Which of the following best describes an SNMP inform request? a. Requires no acknowledgment b. Requires an acknowledgment from the SNMP agent c. Requires an acknowledgment from the SNMP manager d. Only SNMP traps can be implemented on Cisco IOS routers 20 What UDP port number will SNMP traps be sent from? a. 21 b. 22 c. 161 d. 162 21 What TCP port number will an SNMP inform acknowledgment packet be sent to? a. 21 b. 22 c. 23 d. 161 e. 162 f. None of the above
- 132. “Do I Know This Already?” Quiz 109 22 To restrict SNMP managers from the source network 131.108.1.0/30, what IOS command is required? a. ip http enable 131.108.1.1 131.108.1.2 b. snmp community 131.108.1.1 131.108.1.2 c. snmp-server community SimonisCool ro 4 access-list 4 permit 131.108.1.0 0.0.0.252 d. snmp-server community SimonisCool ro 4 e. snmp-server community SimonisCool ro 1 access-list 11 permit 131.108.1.0 0.0.0.252
- 133. 110 Chapter 3: Application Protocols Foundation Topics Domain Name System This section covers Domain Name System (DNS) and sample configurations used on Cisco IOS routers. DNS’s primary use is to manage Internet names across the World Wide Web. For users or clients to use names instead of 32-bit IP addresses, the TCP/IP model designers developed DNS to translate names into IP addresses. DNS uses TCP and UDP port number 53. In a large IP environment, network users need an easier way to connect to hosts without having to remember 32-bit IP addresses—that’s where DNS comes into play. DNS provides a service that allows users to use a host’s name in place of an IP Address to connect to hosts. When DNS services are running, the host’s name is used to request its IP address from a DNS server. The DNS server is a host running the DNS service, and it is configured to do the translation for the user transparently. In other words, the user never sees the DNS request and host-to-IP address translation. The client simply connects to a host name, and the DNS server does the translation. For example, the website www.cisco.com is translated to the IP address 198.133.129.25. DNS is a distributed database where organizations can use a predefined name or extension to all their devices. Nations can use extensions to define hosts residing in their country. For example, the extension for Australia is defined as .au. To reach the Cisco website in Australia, a user would type www.cisco.com.au in a web browser. A regulatory body called the Internet Registration Authority manages domain names. Similar to DNS, Cisco routers can be configured to locally look up names so network administrator can simply type a name rather than an IP address. Local names can also be configured for devices. To illustrate a local DNS lookup on a Cisco IOS router, look at the following Cisco router command that provides a host lookup. (Note: a router will not provide DNS server responses to client devices such as PCs or UNIX hosts.) The following IOS command defines a local name to IP address: ip host name [tcp-port-number] ip address1 [ip address2...ip address8] You can assign more than one IP address to any given name. Example 3-1 displays three hosts and their corresponding IP addresses.
- 134. Domain Name System 111 Example 3-1 Local IP Host Configuration on a Cisco Router ip host Router1 131.108.1.1 ip host Router2 131.108.1.2 ip host Router3 131.108.1.3 The three hosts, named Router1, Router2, and Router3 in Example 3-1, are translated into IP addresses 131.108.1.1, 131.108.1.2, and 131.108.1.3. When a network administrator types in the host name, the router translates the name to an IP address. Example 3-2 displays a network administrator Telneting from router, R1, to the remote host, Router2. Example 3-2 Local DNS Translation R1#router2 Translating "router2" Trying Router2 (131.108.1.2)... Open 131.108.1.2 User Access Verification Password: ***** Router2> When the network administrator types the name router2 (DNS names are not case-sensitive) at the exec prompt, the Cisco IOS router does a local host lookup for the name router2 and translates the address to 131.108.1.2. What would happen if you typed a name that was not configured locally? Example 3-3 displays the sample output from a Cisco router when an unknown name (ccie, in this case) is typed at the exec prompt. Example 3-3 Name Translation for ccie R1#ccie Translating "ccie" Translating "ccie" % Unknown command or computer name, or unable to find computer address R1# From the privileged exec prompt on Router R1 in Example 3-3, R1 does a local DNS lookup, discovers there is no DNS translation, and provides the shaded error message. Scalability issues with local host configuration can become a nightmare with a large network. Thankfully, DNS servers can be placed around the network (typically in the core infrastructure) to ensure that only a few devices in the network require the full table of names and IP address translations. The World Wide Web has DNS servers that provide DNS mapping for websites.
- 135. 112 Chapter 3: Application Protocols NOTE By default, Cisco routers search for a DNS server. To disable this feature, use the IOS command no ip domain-lookup. This stops the router from querying a DNS server whenever a name translation is required. This command is a definite time saver for the CCIE Security Lab exam. To enable a Cisco IOS router to perform DNS lookup to a remote DNS server, the following steps are required: Step 1 For local DNS entries, you must specify any local host mapping with the following IOS command (note that the tcp-port-number is used for connections on a different TCP port number other than the default, 23): ip host name [tcp-port-number] ip address1 [ip address2...ip address8] Step 2 Specify the domain name or a domain list (Cisco routers can be configured with multiple domain names) with the following IOS commands: — ip domain-name name defines a default domain name that the Cisco IOS Software uses to complete unqualified host names. — ip domain-list name defines a list of default domain names to complete unqualified host names. Step 3 Specify the DNS server or servers with the following IOS command: ip name-server server-address1 [server-address2...server-address6] Devices such as PCs can also be configured for DNS servers and domain names. Example 3-4 configures a router named R1 with the domain name cisco.com. The domain name servers are 131.108.255.1 and 131.108.255.2. Example 3-4 DNS Configuration R1(config)#ip domain-name cisco.com R1(config)#ip name-server 131.108.255.1 R1(config)#ip name-server 131.108.255.2 When a network administrator types a name (not a valid IOS command, of course), the Cisco router attempts to translate the name into an IP address, first from the DNS server with the IP address 131.108.255.1, and then from the DNS server 131.108.255.2. Example 3-5 displays a successful DNS query and translation to the host named ccie (another Cisco router) from the DNS server 131.108.255.1.
- 136. Trivial File Transfer Protocol 113 Example 3-5 DNS Query from the Exec Prompt R1#ccie ! Administrator types ccie Translating "ccie" ! Query is sent to first configured DNS server Trying CCIE (131.108.255.1)... Open 131.108.255.1 User Access Verification Password: **** CCIE> NOTE In Example 3-5, a Telnet connection requires a password authentication phase (and for all Telnet-based connections, for that matter). You can disable the Telnet login password on Cisco routers with the command no login under the VTY line configuration, as follows: line vty 0 4 no login Trivial File Transfer Protocol Trivial File Transfer Protocol (TFTP) is a protocol that allows data files to be transferred from one device to another using the connectionless protocol, UDP. TFTP uses UDP port number 69. TFTP is typically used in environments where bandwidth is not a major concern and IP packets that are lost can be resent by the higher layers (typically the application layer). TFTP has little security. In fact, the only security available to TFTP transfer is defining the directory on the host TFTP device and the filenames that will be transferred. 1 TFTP has no method to authenticate username or password; the TFTP packet has no field enabling the exchange of username or password between two TCP/IP hosts. 2 TFTP directory security (configurable on UNIX and Windows platforms) on the TFTP server is accomplished by allowing a predefined file on the server access. This allows the remote hosts to TFTP the file from the remote TFTP client. For example, to copy a con- figuration file from a Cisco router to a UNIX or Windows host, the file must be predefined on the TFTP server with the appropriate access rights defined. Upgrading Cisco IOS images is a great example of when TFTP is useful; IOS images can be downloaded from a TFTP server to the Cisco router’s system flash. Cisco offers a free TFTP application protocol, available at the following URL: www.cisco.com/public/sw-center/sw-web.shtml Now, configure the Cisco application software, Cisco TFTP, to enable a Cisco router to download a version of IOS code.
- 137. 114 Chapter 3: Application Protocols Figure 3-1 displays the available options when configuring the TFTP application software. Figure 3-1 Cisco TFTP Application Software Options Includes logging of all TFTP transfers Defines from where files are to be downloaded The TFTP directory in Figure 3-1 is defined as c:tftpboot. On the host TFTP server (in this case a Windows 2000 PC), the IOS images reside in the tftpboot directory at c:tftpboot. This download directory option is a configurable option, and you can select any valid directory on the host TFTP server. The file is located in the tftpboot directory. In this example, the IOS image is named c2600-js-mz.121-5.T10.bin. To copy an IOS image from a TFTP server, the IOS command is copy tftp flash. Example 3-6 displays a TFTP request for the file c2600-js-mz.121-5.T10.bin from a TFTP server with an IP address of 150.100.1.253. Example 3-6 TFTP File Transfer R1#copy tftp flash Address or name of remote host []? 150.100.1.253 Source filename []? c2600-js-mz.121-5.T10.bin Destination filename [c2600-js-mz.121-5.T10.bin]? c2600-js-mz.121-5.T10.bin Erase flash: before copying? [confirm]Y Erasing the flash filesystem will remove all files! Continue? [confirm]Y Erasing device... eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee eeeeee ...erased Erase of flash: complete Loading c2600-js-mz.121-5.T10.bin from 150.100.1.253 (via Ethernet0/0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
- 138. File Transfer Protocol 115 Example 3-6 TFTP File Transfer (Continued) [OK - 11432808/22864896 bytes] Verifying checksum... OK (0xBC59) 11432808 bytes copied in 106.126 secs (107856 bytes/sec) R1# The file (c2600-js-mz.121-5.T10.bin) is successfully copied and placed on the flash system on Router R1. The only two mechanisms for security permitted with TFTP are the filename and directory. TFTP has no mechanism for checking username and password. On a UNIX server where the TFTP server daemon is installed, the file to be copied must have the appropriate access rights. In UNIX, the Touch command is used to allow a TFTP request. For a Windows- based platform, the software must be configured to permit file creation on the Windows-based file system. FTP, on the other hand, is a connection-based protocol, where username and password combi- nations are used to authorize file transfers. File Transfer Protocol File Transfer Protocol (FTP), an application layer protocol of the TCP/IP protocol suite of applications, allows users to transfer files from one host to another. Two ports are required for FTP—one port is used to open the connection (port 21), and the other port is used to transfer data (20). FTP runs over TCP and is a connection-oriented protocol. To provide security, FTP allows usernames and passwords to be exchanged before any data can be transferred, adding some form of security authentication mechanism to ensure that only valid users access FTP servers. The advantages of FTP are the ability to list a remote FTP server’s full list of directories and ensure that only valid users are connected. The file transfer progress can be displayed to the FTP client, as well. Many FTP applications are available, and the range of options is endless. For example, on the CCIE Security lab exam, the application Reflection 2000 can be used for Telnet and FTP. For more details on this application, visit www.wrq.com/products/reflection/. NOTE FTP connection issues are typically communicated by end users (FTP clients) as poor network performance when the problem might actually be a result of filtering the FTP data on port 20. For example, when a client successfully logs into an FTP server remotely but fails to list the remote FTP server’s directory or to transfer files, this can indicate a problem with the FTP data port (via TCP port 20) or an access list problem on the remote network.
- 139. 116 Chapter 3: Application Protocols FTP clients can be configured for two modes of operation: • Active mode • Passive mode Active FTP Active FTP is defined as one connection initiated by the client to the server for FTP control connection. Remember that FTP requires two port connections through TCP ports 20 (data) and 21 (control). The second connection is made for the FTP data connection (where data is transferred), which is initiated from the server back to the client. Active FTP is less secure than passive mode because the FTP server, which, in theory, could be any host, initiates the data channel. Figure 3-2 displays the active FTP mode of operation between an FTP client and FTP server. Figure 3-2 FTP Active Mode FTP FTP Server Client Active FTP FTP Port 20 Data 21 Command > 1023 > 1023 FTP Port Number Local TCP 1 Number Number 2 ok 3 Data Channel 4 ok
- 140. File Transfer Protocol 117 Figure 3-2 displays a typical FTP mode of operation between a client PC and FTP server in active mode. The following steps are completed before FTP data can be transferred: 1 The FTP client opens a control channel on TCP port number 21 to the FTP server. The source TCP port number on the FTP client is any number randomly generated above 1023. 2 The FTP server receives the request and sends an acknowledgment. FTP commands are exchanged between client and server. 3 When the FTP client requests a directory list or initiates a file transfer, the client sends a command (FTP port command). The FTP server then opens (initiates) a data connection on the FTP data port, TCP port 20. 4 The FTP client responds and data can be transferred. Passive FTP Passive FTP still requires a connection for the initial FTP control connection, which is initiated by the FTP client to the server. However, the second connection for the FTP data connection is also initiated from the client to the server (the reverse of active FTP). Figure 3-3 displays a typical FTP mode of operation between a client PC and FTP server in passive mode. Figure 3-3 FTP Passive Mode FTP FTP Server Client Passive FTP FTP Port 20 Data 21 Command > 1023 > 1023 FTP Port Number 1 Number PASV FTP Port > 1023 number 2 ok Data Channel 3 ok 4
- 141. 118 Chapter 3: Application Protocols The following steps are completed before data can be transferred: 1 The FTP client opens a control channel on TCP port 21 to the FTP server and requests passive mode with the FTP command pasv, or passive. The source TCP port number is any number randomly generated above 1023. 2 The FTP server receives the request and agrees to the connections using a randomly generated, local TCP port number greater than 1023. 3 The FTP client receives the information, selects a local TCP number randomly generated and greater than 1023, and opens a data channel to the FTP server (on TCP greater than 1023). 4 The FTP server receives the FTP client’s request and agrees to the connection. In passive FTP, the client initiates both the control connection and the data connection. In active mode, the FTP server initiates the FTP data channel. When using passive FTP, the probability of compromising data is less because the FTP client initiates both connections. Hypertext Transfer Protocol Hypertext Transfer Protocol (HTTP), used by web browsers and web servers, transfers files, such as text and graphic files. HTTP can also authenticate users with username and password verification between client and web servers. Cisco IOS routers can be configured from a browser client. By default, Cisco routers are disabled for HTTP server (HTTP is enabled by default on a few Cisco 1000 models, namely the Cisco 1003,1004, and 1005 model routers), and there have been issues with users entering certain hash pairs to gain access to configuration commands when HTTP has been enabled. Fortunately, the latest versions of Cisco IOS code have been strengthened, and users must now enter valid username and password pairings to gain access to the configuration options. HTTP authentication is not very secure, so Secure Socket Layer (SSL) was developed to allow a stronger method to authenticate HTTP users. NOTE For more details on the HTTP security vulnerability with Cisco IOS, please visit www.cisco.com/warp/public/707/ioshttpserver-pub.shtml To view the router’s home page, use a web browser pointed to http://a.b.c.d, where a.b.c.d is the IP address of your router or access server. If a name has been set via a DNS server, use http://router-name.
- 142. Hypertext Transfer Protocol 119 Figure 3-4 displays a sample HTTP request to a remote router with the IP address 10.66.32.5 displaying the request for a valid username and password. The default username is the Cisco router’s local host name, and the password is set to the enable or secret password. Figure 3-4 HTTP Authentication on a Cisco Router IP Address of Remote Router Username and password are entered here. After the user is authenticated, the user enters the remote IP address or DNS name. Varying forms of authentication for login can be set using the ip http authentication command. However, the default login method is entering the host name as the username and the enable or secret password as the password, as displayed in Figure 3-4. After the user is authenticated with the correct username and password pairing, the user is permitted HTTP access. Figure 3-5 displays the options available after authentication. After HTTP is authenticated, the available options are identical to the command-line interface (CLI) prompt. Depending on the configurable username and password pairing on the router, you will have certain privileged levels. For example, if you type the username as the local host name of the IOS router and the enable or secret password as completed in Figure 3-5, you will have privilege level 15, which is the same as the PRIV level on the CLI permitting all IOS commands. If the username/password pairing has a lower privileged level (via the ip http authentication command), the corresponding IOS command set will be available via HTTP. For example, a user with privilege level 5 will not have the option to reload the router.
- 143. 120 Chapter 3: Application Protocols Figure 3-5 HTTP Web Page on a Cisco Router HTTP options; simply click to expand IOS command set. Help Options NOTE The command to disable HTTP server on a Cisco router is no ip http server. To set username/password pairs, use the following IOS command: username username privilege [0-15] password password You can also define the HTTP port number with the following command: ip http [0-65535] The default is 80. Secure Socket Layer Secure Socket Layer (SSL) is an encryption technology for web host devices used to provide secure transactions. For example, a secure transaction is required when clients enter their credit card numbers for e-commerce via their browser. When the end user enters a web address via an Internet browser, such as Internet Explorer, instead of entering HTTP: //web address in the address window, the end user enters HTTPS://web address.
- 144. Simple Network Management Protocol 121 Secure Hypertext Transfer Protocol secure site, or HTTPS, transports HTTP-based traffic over an SSL connection and provides a stronger authentication mechanism than HTTP. HTTPS runs over TCP port 443. SSL is defined in RFC 2246. The SSL Handshake Protocol was first developed by Netscape Communications Corporation to provide security and privacy over the World Wide Web. The SSL protocol supports server and client authentication. The SSL protocol is application-independent, allowing protocols like HTTP, FTP, and Telnet to be layered on top of it transparently. In other words, it is a session layer-based protocol. Cisco has developed a number of content-based switches to accelerate this communication, such as the Cisco SCA 11000 Series Secure Content Accelerator. The Cisco SCA 11000 Series Secure Content Accelerator is an appliance-based solution that increases the number of secure connections supported by a website by offloading the processor- intensive tasks related to securing traffic with SSL. After an SSL session is established, no further authentication is required. Chapter 5, “Security Protocols,” broadens this discussion on public security by discussing topics such as private and public keys, and how keys are exchanged through the Certificate Authority (CA) to ensure that SSL is secure. Simple Network Management Protocol Application layer protocol, Simple Network Management Protocol (SNMP), is used to manage IP devices. SNMP is part of the TCP/IP application layer suite. SNMP allows network admin- istrators the ability to view and change network parameters and monitor connections locally and remotely. Managing network performance over a period of time is one of the major functions that SNMP provides. There are three version of SNMP: • SNMP Version 1 (SNMPv1) • SNMP Version 2 (SNMPv2) • SNMP Version 3 (SNMPv3) Both SNMPv1 and SNMPv2 use a community-based form of security. The community string allows access to the SNMP agent and can also be defined by an IP address access control list and password. To set up the community access strings to permit access to the Simple Network Management Protocol (SNMP) on a Cisco IOS router, use the snmp-server community global configuration command: snmp-server community string [view view-name] [ro | rw] [number]
- 145. 122 Chapter 3: Application Protocols Table 3-1 describes this syntax. Table 3-1 snmp-server community Command Syntax Description Syntax Description string Case-sensitive community string that acts like a password and permits access to the SNMP protocol. view view-name (Optional) Name of a previously defined view. The view defines the objects available to the community. ro (Optional) Specifies read-only access. Authorized management stations are able to retrieve only MIB objects. rw (Optional) Specifies read-write access. Authorized management stations are able to retrieve and modify MIB objects. number (Optional) Integer from 1 to 99 that specifies an access list of IP addresses that are allowed to use the community string to gain access to the SNMP agent. SNMP servers collect information from remote devices known as SNMP agents. SNMP packets are sent and received by devices on UDP ports 161 (SNMP servers) and 162 (SNMP agents). The Management Information Base (MIB) is a virtual information storage area for network management information consisting of collections of managed objects. Within the MIB are collections of related objects, defined in MIB modules. MIB modules are written in the SNMP MIB module language, as defined in STD 58, RFC 2578, RFC 2579, and RFC 2580. SNMP port 161 is used to query SNMP devices, and SNMP port 162 is used to send SNMP traps. SNMP runs over UDP and is secured by a well-known, case-sensitive community string. SNMP Notifications SNMP’s key feature is the ability to generate notifications from SNMP agents. Cisco routers can be configured to send SNMP traps or informed requests to a Network Management System (NMS) where a network administrator can view the data. Figure 3-6 displays the typical communication between an SNMP manager and the SNMP agent (for example, a Cisco-enabled SNMP router). Unsolicited notifications can be generated as traps or inform requests. Traps are messages alerting the SNMP manager to a condition on the network (sent by the SNMP agent). Inform requests (informs) are traps that include a request for confirmation of receipt from the SNMP manager. SNMP notifications can indicate improper user authentication, restarts, the closing of a connection, loss of connection to a neighbor router, or other significant events.
- 146. Simple Network Management Protocol 123 Figure 3-6 Communication Between SNMP Manager and SNMP Agent Trap (no acknowledge) or Inform Requests (acknowledgment sent) UDP 162 SNMP SNMP Manager Agent UDP 161 Inform acknowledgment sent The major difference between a trap and an inform packet is that an SNMP agent has no way of knowing if an SNMP trap was received by the SNMP manager. An inform request will be sent continually until an acknowledgment is received by the sending SNMP agent. Table 3-2 defines some of the common terminology used in SNMP. Table 3-2 SNMP Terminology Term Description Managed device A network node that contains an SNMP agent and resides on a managed network. Managed devices collect and store management information and make this information available to Network Management Systems using SNMP. Agent A network management software module that resides in a managed device. An agent has local knowledge of management information and translates that information into a form compatible with SNMP. Network Management Executes applications that monitor and control managed devices. System (NMS) NOTE Managed devices are monitored and controlled using three common SNMP commands: read, write, and trap. The read command is used by an NMS to monitor managed devices. The NMS examines different variables that are maintained by managed devices. The write command is used by an NMS to control managed devices. The NMS changes the values of variables stored within managed devices. The trap command is used by managed devices to asynchronously report events to the NMS. For example, Cisco IOS routers can be configured to report errors, such as emergencies alerts, to the NMS for urgent action, such as low memory resources or unauthorized access. When certain types of events occur, a managed device sends a trap to the NMS.
- 147. 124 Chapter 3: Application Protocols Management Information Base (MIB), a database of network management information, is used and maintained by a management protocol such as SNMP. The value of an MIB object can be changed or retrieved using SNMP commands, usually through a GUI network management system. Cisco supports a number of defined and proprietary MIB commands. If the snmp-server community command is not used during the SNMP configuration session, it will automatically be added to the configuration after the snmp-server host command is used. In this case, the default password (string) for the snmp-server community is taken from the snmp-server host command. You must always set the community string manually; otherwise, your router could be left vulnerable to SNMP get commands. Example 3-7 configures a Cisco IOS router for SNMP support. Example 3-7 Sample SNMP Configuration snmp-server community public RO snmp-server enable traps config snmp-server host 131.108.255.254 isdn The IOS command snmp-server community public RO enables SNMP on a Cisco router. This command is also used to restrict access via SNMP. The community string is defined as public and acts as a password protection mechanism against unauthorized users. The community string is sent in every SNMP packet, so an incorrect community string results in no authorized access to the SNMP agent. The read-only attribute means that no configuration changes will be permitted via an SNMP. The IOS command snmp-server enable traps config advises the NMS of any configura- tion changes. The IOS command snmp-server host 131.108.255.254 isdn alerts the host 131.108.254.254 of any ISDN traps. ISDN traps can include link flapping or high link usage, for example. (See Table 3-2 for a comprehensive list of traps.) To specify the recipient of an SNMP notification operation, use the snmp-server host global configuration command. To remove the specified host, use the no form of this command. snmp-server host host-addr [traps | informs] [version {1 | 2c | 3 [auth | noauth | priv]}] community-string [udp-port port] [notification-type] Table 3-3 expands the snmp-server host IOS command and presents the full range of options, including MD5 authentication.
- 148. Simple Network Management Protocol 125 Table 3-3 snmp-server host Command Syntax Description Meaning host-addr Name or Internet address of the host (the targeted recipient). traps (Optional) Sends trap messages to this host. This is the default. informs (Optional) Sends Inform messages to this host. version (Optional) Version of the SNMP used to send the traps. Version 3 is the most secure model because it allows packet encryption with the priv keyword. If you use the version keyword, one of the following must be specified: 1—SNMPv1. This option is not available with informs. 2c—SNMPv2C. 3—SNMPv3. The following three optional keywords can follow the 3 keyword: auth—(Optional) Enables Message Digest 5 (MD5) and Secure Hash Algorithm (SHA) packet authentication. noauth—(Default) The noAuthNoPriv security level. This is the default if the [auth | noauth | priv] keyword choice is not specified. priv—(Optional) Enables Data Encryption Standard (DES) packet encryption (also called privacy). community-string Password-like community string sent with the notification operation. Although you can set this string using the snmp-server host command by itself, it is recommended that you define this string using the snmp-server community command prior to using the snmp-server host command. udp-port port (Optional) UDP port of the host to use. The default is 162. notification-type (Optional) Type of notification to be sent to the host. If no type is specified, all notifications are sent. The notification type can be one or more of the following keywords: bgp—Sends Border Gateway Protocol (BGP) state change notifications. calltracker—Sends Call Tracker call-start/call-end notifications. config—Sends configuration notifications. dspu—Sends downstream physical unit (DSPU) notifications. entity—Sends Entity MIB modification notifications. envmon—Sends Cisco enterprise-specific environmental monitor notifications when an environmental threshold is exceeded. frame-relay—Sends Frame Relay notifications. hsrp—Sends Hot Standby Routing Protocol (HSRP) notifications. continues
- 149. 126 Chapter 3: Application Protocols Table 3-3 snmp-server host Command (Continued) Syntax Description Meaning notification-type isdn—Sends Integrated Services Digital Network (ISDN) notifications. (Continued) llc2—Sends Logical Link Control, type 2 (LLC2) notifications. repeater—Sends standard repeater (hub) notifications. rsrb—Sends remote source-route bridging (RSRB) notifications. rsvp—Sends Resource Reservation Protocol (RSVP) notifications. rtr—Sends SA Agent (RTR) notifications. sdlc—Sends Synchronous Data Link Control (SDLC) notifications. sdllc—Sends SDLLC notifications. snmp—Sends any enabled RFC 1157 SNMP linkUp, linkDown, authenticationFailure, warmStart, and coldStart notifications. stun—Sends serial tunnel (STUN) notifications. syslog—Sends error message notifications (Cisco Syslog MIB). Specify the level of messages to be sent with the logging history level command. tty—Sends Cisco enterprise-specific notifications when a Transmission Control Protocol (TCP) connection closes. voice—Sends SNMP poor quality of voice traps when used with the snmp enable peer-trap poor qov command. x25—Sends X.25 event notifications. * Table 3-3 is sourced from the Cisco Documentation website, www.cisco.com/univercd/cc/td/doc/product/ software/ios121/121cgcr/fun_r/frprt3/frd3001.htm#xtocid655917. SNMP is disabled by default on Cisco IOS routers. SNMP Examples The following example assigns the SimonisCool string to SNMP, allowing read-only access, and specifies that IP access list 4 can use the community string: R1(config)# snmp-server community SimonisCool ro 4 R1(confiog)# access-list 4 permit 131.108.1.0 0.0.0.255 The hosts on network 131.108.1.0/24 are permitted SNMP access if the read-only string is set to SimonisCool. This enables an added feature to ensure that devices that source SNMP information are from a trusted or internal network. The following example assigns the string SnR to SNMP, allowing read-write access to the objects in the restricted view (read only): R1(config)# snmp-server community SnR view restricted ro
- 150. Simple Mail Transfer Protocol 127 The following example disables all versions of SNMP: R1(config)# no snmp-server The following example enables the router to send all traps to the host, host.cisco.com, using the community string public: R1(config)# snmp-server enable traps R1(config)# snmp-server host host.cisco.com public In the following example, the BGP traps are enabled for all hosts, but only the ISDN traps are enabled to be sent to an actual host named simon: R1(config)# snmp-server enable traps bgp R1(config)# snmp-server host simon public isdn The following example enables the router to send all inform requests to the host test.cisco.com using the community string publiC: R1(config)# snmp-server enable traps R1(config)# snmp-server host test.cisco.com informs publiC Simple Mail Transfer Protocol The Simple Mail Transfer Protocol (SMTP) mechanism is used for providing e-mail services to IP devices over the Internet. SMTP is defined in RFC 821. Typically, two mail servers will talk SMTP to exchange mails. After the mails are exchanged, the users can read/retrieve their mail from the mail server. This can be done using any mail client, such as Pine, Eudore, Outlook, and so on, which use different protocols, such as Post office protocol or POP3, to connect to the server. SMTP uses well-known ports TCP port 25 and UDP port 25. A process or daemon running on a server will use SMTP to send mail to clients. A program called Sendmail is a common tool used for SMTP mail transfer. Recently, a new release of SMTP, called Enhanced SMTP (ESMTP), was developed. You are not required to know this protocol for the written exam. NOTE The client and SMTP server send various commands when communicating. The most common command is HELO check. The HELO Check command introduces the calling machine to the receive machine; the client will advertise the mail server its host name. There are numerous other commands. A great resource if you are interested in further details on the Sendmail application is the book “Sendmail,” by Bryan Costales and Eric Allman (O’Reilly and Associates, ISBN 1-56592-839-3). To test if a remote host’s SNMP mail is operational and active, you can use Telnet with the defined HELO command. A summary of other useful SMTP commands is presented for your reference in case you are questioned on these commands during the exam: HELLO (HELO)—Identifies the sender.
- 151. 128 Chapter 3: Application Protocols MAIL (MAIL)—Initiates a mail transaction in which the mail data is delivered to mailboxes. RECIPIENT (RCPT)—Identifies an individual recipient of the mail data; multiple use of the command is needed for multiple users. DATA (DATA)—The lines following the command are the mail data in ASCII character codes. SEND (SEND)—Initiates a mail transaction in which the mail data is delivered to one or more terminals. SEND OR MAIL (SOML)—Initiates a mail transaction in which the mail data is delivered to one or more terminals or mailboxes. SEND AND MAIL (SAML)—Initiates a mail transaction in which the mail data is delivered to one or more terminals and mailboxes. RESET (RSET)—The current mail transaction is to be aborted. Any stored sender, recipients, and mail data must be discarded, and all buffers and state tables cleared. The receiver must send an OK reply. VERIFY (VRFY)—This is to verify if a user exists; a fully specified mailbox and name are returned. NOOP (NOOP)—Specifies no action other than that the receiver sent an OK reply. QUIT (QUIT)—The receiver must send an OK reply and then close the transmission channel. Network Time Protocol Network Time Protocol (NTP) is used for accurate time keeping and can reference atomic clocks that are present on the Internet, for example. NTP is capable of synchronizing clocks within milliseconds and is a useful protocol when reporting error logs (for instance, from Cisco routers). For NTP, the defined ports are UDP port 123 and TCP 123. NTP can support a connection- orientated server (TCP guarantees delivery) or connectionless (UDP for non-critical applications). An NTP network usually gets its time from an authoritative time source, such as a radio clock or an atomic clock attached to a time server. NTP then distributes this time across the network. NTP is extremely efficient; no more than one packet per minute is necessary to synchronize two machines to within a millisecond of one another. NOTE NTP uses the concept of a stratum to describe how many NTP hops away a machine is from an authoritative time source. A stratum 1 time server has a radio or atomic clock directly attached; a stratum 2 time server receives its time via NTP from a stratum 1 time server, and so on. Cisco routers cannot support stratum 1 (in other words, you cannot connect a Cisco router to an atomic clock source) and need to derive an atomic clock source from the Internet. NTP can also authenticate sessions.
- 152. Network Time Protocol 129 Figure 3-7 displays a simple two-router network where Router R1 will be configured to supply a clock source to the Router R2. In this example, you will configure authentication and ensure that the NTP peer between the two routers is secure. Figure 3-7 NTP Sample Configuration My clock is set to August 9, 2002, time 10:47:48 a.m. 131.108.3.0/30 Ethernet0/0 Frame Relay Ethernet0/0 NTP NTP 172.108.1.1/24 Server Client 172.108.2.1/24 Send Receive R1 NTP NTP R2 Serial0/0.1 Serial0/0.2 I have NTP atomic clock source; my stratum value is 2. The following steps are required when enabling NTP on a Cisco router: 1 Define the time zone with the following command: clock timezone zone hours [minutes] 2 Configure the master NTP router (this router will supply a clock to other routers) with the following command: ntp master [stratum value] The stratum value is 1 to 15, with 1 representing the best clock source. 3 To configure a remote NTP peer to a Cisco router with a better stratum value, use the following IOS command: ntp peer ip-address [version number] [key keyid] [source interface] [prefer] Table 3-4 displays the required parameters for the ntp peer command. 4 To define NTP to authenticate the NTP session, use the following IOS commands: ntp trusted-key key-number The key-number is the authentication key to be trusted. ntp authentication-key number md5 value
- 153. 130 Chapter 3: Application Protocols Table 3-4 ntp peer Command Defined Syntax Description ip-address IP address of the peer providing, or being provided, the clock version (Optional) Defines the Network Time Protocol (NTP) version number number (Optional) NTP version number (1 to 3) key (Optional) Defines the authentication key keyid (Optional) Authentication key to use when sending packets to this peer source (Optional) Names the interface interface (Optional) Name of the interface from which to pick the IP source address prefer (Optional) Makes this peer the preferred peer to provide synchronization To ensure that R1 sends R2 a clock source via NTP, R1 must be configured to send NTP traffic over the Frame Relay cloud with the command ntp broadcast. To specify that a specific interface should send NTP broadcast packets, use the ntp broadcast interface configuration command. Similarly, R2 must receive NTP traffic and is considered an NTP client with the IOS command ntp broadcast client. R2’s Serial 0/0 interface is configured with the command ntp broadcast client. Example 3-8 configures Router R1 in Figure 3-7 to supply a clock source to Router R2. Example 3-8 NTP Configuration on R1 clock set 10:20:00 9 August 2002 clock timezone UTC 10 !Interface configuration interface serial0/0 ntp broadcast !Global configuration ntp authentication-key 1 md5 121A061E17 7 ntp authenticate ntp trusted-key 1 ntp master 2 ntp peer 131.108.2.1 key 1 Notice that the router is set to the correct time first with the IOS command clock set. The router is configured for the UTC time zone and 10 hours behind UTC time. The authentication key is set to 1. Example 3-9 configures R2 to get the clock from R1 using the same MD5 password (set to ccie) from Example 3-8.
- 154. Network Time Protocol 131 Example 3-9 NTP Configuration on R2 interface serial0/0 ntp broadcast client !Global configuration ntp authentication-key 1 md5 ccie ntp authenticate ntp trusted-key 1 ntp trusted-key ntp peer 131.108.1.1 key 1 Example 3-10 displays the two clocks on Routers R1 and R2 confirming that R1 is sending R2 the correct time via NTP. Example 3-10 show clock on R1 and R2 R1#show clock 10:47:48.508 UTC Fri Aug 9 2002 R2#show clock 10:47:48.508 UTC Fri Aug 9 2002 Example 3-11 confirms that NTP is authenticated (the remote stratum value is 2) by viewing the output of the IOS command show ntp associations detail. Example 3-11 show ntp associations detail Command on R2 R2# show ntp associations detail 131.108.1.1 configured, authenticated, selected, sane, valid, stratum 2 authenticated ref ID .LOCL., time C0FD8D45.0B1C72E0 (10:37:25.043 UTC Fri Aug 9 2002) our mode active, peer mode passive, our poll intvl 64, peer poll intvl 64 root delay 0.00 msec, root disp 0.03, reach 1, sync dist 15878.372 delay 6.67 msec, offset 297909193935.7106 msec, dispersion 15875.02 precision 2**16, version 3 org time C0FD8D45.BA55E231 (10:37:25.727 UTC Fri Aug 9 2002) rcv time AF3BD17B.CBA5DDF0 (10:04:11.795 UTC Mon Mar 1 1993) xmt time AF3BD17B.C9CB2BA2 (10:04:11.788 UTC Mon Mar 1 1993) filtdelay = 6.67 0.00 0.00 0.00 0.00 0.00 0.00 0.00 filtoffset = 2979091 0.00 0.00 0.00 0.00 0.00 0.00 0.00 filterror = 0.02 16000.0 16000.0 16000.0 16000.0 16000.0 16000.0 16000.0 131.108.255.1 dynamic, authenticated, our_master, sane, valid, stratum 2 our_master ref ID .LOCL., time C0FD8D05.0AE0774C (10:36:21.042 UTC Fri Aug 9 2002) our mode passive, peer mode active, our poll intvl 64, peer poll intvl 64 root delay 0.00 msec, root disp 0.03, reach 2, sync dist 1.007 delay 0.00 msec, offset 0.0000 msec, dispersion 16000.00 precision 2**16, version 3 org time C0FD8D43.0B54AAFA (10:37:23.044 UTC Fri Aug 9 2002) rcv time AF3BD179.1C9F231D (10:04:09.111 UTC Mon Mar 1 1993) xmt time AF3BD186.C9CB3361 (10:04:22.788 UTC Mon Mar 1 1993) filtdelay = 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 filtoffset = 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 filterror = 16000.0 16000.0 16000.0 16000.0 16000.0 16000.0 16000.0 16000.0
- 155. 132 Chapter 3: Application Protocols Example 3-11 displays that R2 is dynamically peered to R1 and is authenticated. Secure Shell Secure Shell (SSH) is a protocol that provides a secure connection to a router. Cisco IOS sup- ports version 1 of SSH, which enables clients to make a secure and encrypted connection to a Cisco router. Before SSH was implemented, the only form of security available when accessing devices such as routers was Telnet username/password authentication, which is clearly visible with a network sniffer. Telnet is insecure because a protocol analyzer can view the information in clear text form. Figure 3-8 displays a simple protocol analyzer viewing information between a source address, 10.66.32.5, and the destination address 192.168.1.13 after a Telnet session is initiated by the address (PC) 192.168.1.13/24. Figure 3-8 Sniffer Capture of a Telnet Connection Password will be viewable in Detailed IP these frames. Information Figure 3-8 displays a simple Telnet connection between a PC and a remote router. Figure 3-8 is a packet trace from a client PC Telnet connection to a Cisco IOS router with the IP address 10.32.66.5. The packet trace clearly captures the password prompt sent by the router. Therefore, the prompt is viewable in clear text. If you scrolled down the next few frames (frames numbered 98-103 in Figure 3-8), the password would be clearly visible. An intruder or hacker can piece together the password and gain unauthorized access. For security reasons, these frames are not shown, but it is clear that the Telnet application protocol is not a secure protocol; all data is sent as clear text (including the password exchanged).
- 156. Secure Shell 133 SSH is implemented with TCP port 22 and UDP port 22, and ensures that data is encrypted and untraceable by a network sniffer. SSH can be configured on both Cisco IOS routers and Catalysts switches. Figure 3-9 displays the SSH protocol layers. Figure 3-9 SSH Protocol Layers SSH Connection Layer SSH Authentication Layer SSH Transport Layer TCP UDP IP Network Interface NOTE Lightweight Directory Access Protocol (LDAP) is an Internet protocol that e-mail programs use to look up contact information from a server. For more details on LDAP, visit www.gracion.com/server/whatldap.html. Active Directory is a Windows-defined application that stores and manages network services, resources, and information about where computers and printers are located. Active Directory allows network administrators of 2000 servers the ability to allocate and control how network resources are accessed by clients’ PCs. For more information on Active Directory, visit www.microsoft.com. SSH sits on top of the TCP/IP layers, protecting the hosts from unknown devices. The SSH transport layer is responsible for securing the data using strong encryption authentication. There are currently two versions of SSH: SSHv1 and SSHv2. Cisco IOS only supports SSHv1. UNIX devices support SSH clients and Cisco routers can be configured to allow SSH between the UNIX device and Cisco router to ensure a secure Telnet connection. Currently, Cisco IOS 12.2 supports SSH and a number of hardware platforms, including the 2600 and 3600 series routers. For more detailed information on SSH and the Cisco IOS functional matrix, visit www.ssh.com/products/ssh/ and www.cisco.com/warp/public/707/ssh.shtml, respectively.
- 157. 134 Chapter 3: Application Protocols Foundation Summary The “Foundation Summary” is a condensed collection of material for a convenient review of this chapter’s key concepts. If you are already comfortable with the topics in this chapter and decided to skip most of the “Foundation Topics” material, the “Foundation Summary” will help you recall a few details. If you just read the “Foundation Topics” section, this review should help further solidify some key facts. If you are doing your final preparation before the exam, the “Foundation Summary” offers a convenient and quick final review. Table 3-5 DNS Concepts Concept Description Well-known port numbers UDP Port 53, TCP Port 53 ip host name [tcp-port-number] Configured locally to assign a host name with up to 8 IP ip address1 [ip address2...ip address8] addresses no ip domain-lookup Disables the IP DNS-based host name-to-address translation ip domain-name name Defines a default domain name that the Cisco IOS Software uses to complete unqualified host names ip domain-list name Defines a list of default domain names to complete unqualified host names ip name-server ip address Specifies the address of one or more name servers to use for name and address resolution; up to six name servers permitted Table 3-6 TFTP Concepts Concept Description Well-known port numbers UDP Port 69 (UDP is typically the only supported protocol for TFTP produced by vendors) and TCP Port 69 copy tftp flash Cisco IOS command to copy images from a TFTP server Security Only filename and directory name are methods used to secure transfers Table 3-7 Secure Shell (SSH) Concepts Concept Description Well-known port number TCP port 443. HTTPS HTTP traffic runs over a secure connection. Service/client SSH uses a client server model where clients request secure connections authentication to a host device, such as with a credit card transaction over the World Wide Web.
- 158. Foundation Summary 135 Table 3-8 SNMP Concepts Concept Description Well-known port numbers UDP 161 (SNMP servers) and UDP 162 (SNMP clients). SNMP managed devices An SNMP managed device is a network node that contains an SNMP agent and resides on a managed network. Managed devices collect and store management information and make this information available to Network Management System using SNMP. SNMP agent SNMP Agent is a network management software module that resides in a managed device. An agent has local knowledge of management information and translates that information into a form compatible with SNMP. Table 3-9 SMTP Concepts Concept Description Well-known port numbers TCP 25 and UDP 25 HELO command Used in communications between host and client Table 3-10 NTP Concepts Concept Description Well-known port numbers TCP 123 and UDP 123. ntp master 1-15 Defines stratum value between 1 and 15. clock set hh:mm:ss day month year Manually sets clock on a Cisco router. ntp peer ip-address [version number] [key Defines NTP peers. keyid] [source interface] [prefer] ntp authenticate Enables authentication. ntp authentication-key number md5 value Defines NTP authentication key and password. ntp trusted-key key-number Defines NTP to authenticate NTP session; key-number is the authentication key to be trusted.
- 159. 136 Chapter 3: Application Protocols Q&A The Q & A questions are designed to help you assess your readiness for the topics covered on the CCIE Security written exam and those topics presented in this chapter. This format should help you assess your retention of the material. A strong understanding of the answers to these questions will help you on the CCIE Security written exam. You can also look over the questions at the beginning of the chapter again for review. As an additional study aid, use the CD-ROM provided with this book to take simulated exams, which draw from a database of over 300 multiple-choice questions—all different from those presented in the book. Select the best answer. Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.” 1 According to RFC 1700, what is the well-known TCP/UDP port used by DNS? 2 What does the IOS command no ip domain-lookup accomplish? 3 What is the correct IOS syntax to specify local host mapping on a Cisco router? 4 TFTP uses what well-known, defined TCP/UDP port? 5 What is the correct IOS command to copy a file from a TFTP server to the system flash?
- 160. Q&A 137 6 Define the two modes of FTP. 7 FTP uses what TCP port numbers? 8 What well-known port do Secure Socket Layer (SSL) and Secure Shell (SSH) use? 9 Define SNMP and give an example. 10 What well-known UDP ports are used by SNMP? 11 What IOS command enables SNMP on a Cisco IOS router? 12 Which TCP/UDP port numbers are defined for use by Network Time Protocol or NTP?
- 161. 138 Chapter 3: Application Protocols 13 When defining a stratum value on a Cisco router, what is the range and what value is closest to an atomic clock? 14 Secure Shell (SSH) allows what to be accomplished when in use? 15 What is the difference between an SNMP inform request and an SNMP trap? 16 What does the SNMP MIB refer to? 17 What is the SNMP read-write community string for the following router configuration? snmp-server community simon ro snmp-server community Simon rw 18 Before you can TFTP a file from a Cisco router to a UNIX- or Windows-based system, what is the first step you must take after enabling the TFTP server daemon on both platforms?
- 162. Q&A 139 19 What IOS command can be implemented to restrict SNMP access to certain networks by applying access lists? Can you apply standard, extended, or both? 20 Does TFTP have a mechanism for username and password authentication? 21 Can you use your Internet browser to configure a Cisco router? If so, how? 22 A network administrator defines a Cisco router to allow HTTP requests but forgets to add the authentication commands. What is the default username and password pairing that allows HTTP requests on the default TCP port 80? Can you predefine another TCP port for HTTP access other than port 80?
- 163. 140 Chapter 3: Application Protocols Scenario Scenario 3-1: Configuring DNS, TFTP, NTP, and SNMP This scenario uses a configuration taken from a working Cisco IOS router and tests your skills with DNS, TFTP, NTP, and SNMP. Example 3-12 displays the configuration of a Cisco router named R1. Example 3-12 R1 Running Configuration version 12.1 hostname R1 clock timezone UTC 10 ! no ip domain-lookup ip domain-name cisco.com ip host CCIE 131.108.1.1 ip host Router3 131.108.1.3 ip host Router2 131.108.1.2 ip host Router1 131.108.1.1 ip name-server 131.108.255.1 ip name-server 131.108.255.2 interface Ethernet0/0 ip address 131.108.1.1 255.255.255.0 ! interface Serial0/0 ip address 131.108.255.1 255.255.255.252 ntp broadcast ! no ip http server snmp-server community public RO snmp-server community publiC RW snmp-server host 131.108.255.254 isdn line con 0 ! ntp authentication-key 1 md5 121A061E17 7 ntp authenticate ntp trusted-key 1 ntp master 1 ntp peer 131.108.2.1 key 1 end
- 164. Scenario 3-1: Configuring DNS, TFTP, NTP, and SNMP 141 1 What happens when a network administrator types the host name Router1 at the router prompt? (Select the best two answers.) a. DNS queries are disabled; nothing will be translated. b. The name Router1 is mapped to the IP address 131.108.1.1. c. The administrator could also type CCIE to reach the same IP address (131.108.1.1). d. Because DNS is disabled with the command no ip domain-lookup, the router assumes this is an invalid IOS command and returns the error “% Unknown com- mand or computer name, or unable to find computer address.” e. Local DNSs are case-sensitive so you can only type Router1 to map to 131.108.1.1. 2 The following commands are entered on the router named R1. What are the TFTP server address and TFTP filename stored on the router on board flash? R1#copy tftp flash Address or name of remote host []? 150.100.1.253 Source filename []? c2600-jo3s56i-mz.121-5.T10.bin Destination filename [c2600-jo3s56i-mz.121-5.T10.bin]? c2600-c1 3 R1 supplies an NTP clock source to a remote router. What is the NTP’s peer IP address, and what is the MD5 password used to ensure that NTP sessions are authenticated? 4 What is the SNMP read-write access community string for the following configuration? snmp-server community public RO snmp-server community publiC RW
- 165. 142 Chapter 3: Application Protocols Scenario Answers Scenario 3-1 Solutions 1 Answers: b and c. The host name Router1 (not case-sensitive) is mapped to 131.108.1.1 with the command ip host Router1 131.108.1.1. Also, the IOS command CCIE is mapped to the same name with the IOS command ip host CCIE 131.108.1.1. If you look at the IP address assigned to the Ethernet 0/0, it’s the local IP address. Therefore, if a user types Router1 or CCIE, they will be return to the same router. The following sample display demonstrates this fact: R1#router1 Translating "router1" Trying Router1 (131.108.1.1)... Open User Access Verification Password: R1>quit ! quit commands exit Telnet session and you return ! to the first Telnet connection on R1 [Connection to router1 closed by foreign host] R1#ccie Translating "ccie" Trying CCIE (131.108.1.1)... Open User Access Verification Password: R1> Both the DNS names, CCIE and Router1, are translated to the same IP address, 131.108.1.1. 2 Answer: The TFTP server address is 150.100.1.253 and the filename requested is c2600-jo3s56i-mz.121-5.T10.bin. However, the last command entered is the destina- tion filename, which defines the names stored locally on the system flash. In this case, the network administrator types the filename c2600-c1. 3 Answer: R1 is configured statically to peer to the remote NTP IP address, 131.108.2.1 (ntp peer 131.108.2.1 key 1). The MD5 password is configured but, unfortunately, the configuration will not display the MD5 passwords (encrypted), so it cannot be derived. 4 Answer: The read-only (RO) community string is named public, and the read-write (RW) community string is set to publiC. Community strings are case-sensitive.
- 167. Exam Topics in this Chapter 58 IOS Specifics
- 168. CHAPTER 4 Cisco IOS Specifics and Security This chapter covers the CCIE IOS Specifics blueprint. Unfortunately, the blueprint does not detail the exact requirements, and IOS in general could mean the entire range of topics. We cover topics that are actually possible topics in the written exam and common to the Routing and Switching blueprint. This chapter covers the following topics: • Cisco Hardware—This section covers the hardware components on a Cisco router, namely the System Flash, nonvolatile RAM (NVRAM), and how files are saved to and from a TFTP server. • show and debug Commands—This section covers the most common show and debug commands used on Cisco routers to manage an IP network. • Password Recovery—This section covers how password recovery is completed on Cisco IOS routers. • Basic Security on Cisco Routers—This section reviews some commands used to ensure that Cisco routers are secured with basic passwords. • IP Access Lists— This section covers both standard and extended IP access lists and their formats. “Do I Know This Already?” Quiz This assessment quiz’s purpose is to help you determine how to spend your limited study time. If you can answer most or all these questions, you might want to skim the “Foundation Topics” section and return to it later, as necessary. Review the “Foundation Summary” section and answer the questions at the end of the chapter to ensure that you have a strong grasp of the material covered. If you already intend to read the entire chapter, you do not necessarily need to answer these questions now. If you find these assessment questions difficult, you should read through the entire “Foundation Topics” section and review it until you feel comfortable with your ability to answer all these and the Q & A questions at the end of the chapter.
- 169. 146 Chapter 4: Cisco IOS Specifics and Security Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.” 1 What IOS command will display the System Flash? a. show flash b. show system flash c. show memory d. show process flash 2 The network administrator has forgotten the enable password and all passwords are encrypted. What should the network administrator do to recover the password without losing the current configuration? a. Call the TAC and ask for a special back door password. b. Call the TAC and raise a case to supply the engineering password. c. Reboot the router, press the break key during the reload, and enter ROM mode and change the configuration register. d. Reboot the router, press the break key during the reload, enter ROM mode and change the configuration register, and when the router reloads, remove the old configuration. 3 What is the enable password for the following router? enable password Simon a. More data required b. Simon c. simon or Simon d. You cannot set the password to a name; it must also contain digits. 4 If the configuration register is set to 0x2101, where is the IOS image booted from? a. slot0: b. slot1: c. Flash d. ROM e. TFTP server
- 170. “Do I Know This Already?” Quiz 147 5 What IOS command will copy the running configuration to a TFTP server? (Select the best two answers.) a. copy running-config to tftp b. write network c. copy running-config tftp d. write erase 6 What debug command allows an administrator to debug only packets from the network 131.108.0.0/16? a. debug ip packet b. terminal monitor c. debug ip packet 1 d. access-list 1 permit 131.108.0.0 e. debug ip packet 1 f. access-list 1 permit 131.108.0.0 0.0.255.255 g. debug ip packet 1 h. access-list 1 permit 131.108.0.0 255.255.0.0 7 After entering debug ip packet, no messages appear on your Telnet session. What is the likely cause? a. OSPF routing is required. b. The console port does not support debug output. c. The terminal monitor command is required. d. IP packets are not supported with the debug command. 8 To change the configuration register to 0x2141, what is the correct IOS command? a. copy running-config register b. configuration 0x2141 c. config 0x2141 register d. config-register 0x2142 e. config-register 0x2141
- 171. 148 Chapter 4: Cisco IOS Specifics and Security 9 Where is the startup configuration stored on a Cisco router? a. In the cam table b. NVRAM c. RAM d. Flash e. slot0: 10 Which of the following statements is true? a. The enable secret command overrides the enable password command. b. The enable command overrides the enable secret password command. c. Enable passwords cannot be used when the secret password is used. d. Both a and c are true. 11 A Cisco router has the following configuration: line vty 0 4 login What will happen when you Telnet to the router? a. You will be prompted for the login password. b. You will enter EXEC mode immediately. c. You cannot access the router without the password set. d. More configuration required. 12 A Cisco router has the following configuration: line vty 0 4 no login password cIscO When a Telnet user tries to establish a remote Telnet session to this router, what will happen? a. You will be prompted for the login password cIscO. b. You will enter EXEC mode immediately. c. You cannot access the router without the password set. d. More configuration required. e. You will be prompted for the login password; password case does not matter.
- 172. “Do I Know This Already?” Quiz 149 13 A Cisco router has the following configuration: line vty 0 1 no login password cisco line vty 2 4 login password ciSco When a third Telnet session is established to a remote router with the preceding configuration, what will happen? a. You will be prompted for the login password, which is set to cisco. b. You will be prompted for the login password, which is set to ciSco. c. You will enter EXEC mode immediately. d. You cannot access the router without the password set. e. More configuration required. 14 Which of the following access lists will deny any IP packets sourced from network 131.108.1.0/24 and destined for network 131.108.2.0/24 and permit all other IP-based traffic? a. access-list 1 deny 131.108.1.0 b. access-list 1 deny 131.108.1.0 0.0.0.255 c. access-list 100 permit/deny ip 131.108.1.0 0.0.0.255 131.108.2.0 0.0.0.255 d. access-list 100 deny ip 131.108.1.0 0.0.0.255 131.108.2.0 0.0.0.255 e. access-list 100 permit ip any any 15 An administrator notices a router’s CPU utilization has jumped from 2 percent to 100 percent, and that a CCIE engineer was debugging. What IOS command can the network administrator enter to stop all debugging output to the console and vty lines without affecting users on the connected router? a. no logging console debugging b. undebug all c. line vty 0 4 d. no terminal monitor e. reload the router
- 173. 150 Chapter 4: Cisco IOS Specifics and Security Foundation Topics Cisco Hardware Cisco routers consist of many hardware components. The main components of a Cisco router include the following: • RAM • NVRAM • Flash • CPU • ROM • Configuration registers • Interfaces Figure 4-1 illustrates the hardware components on Cisco routers. Figure 4-1 Components of a Cisco Router Random-Access Memory (RAM) Flash Read-Only Nonvolatile RAM Memory (ROM) (NVRAM) LAN, WAN, Router Interfaces Console, AUX Port Each hardware component is vital for Cisco routers to operate properly. To help you prepare for the CCIE Security written exam, the next few sections present the main concepts you need to know about Cisco hardware components.
- 174. Cisco Hardware 151 Random-Access Memory (RAM) Routers use random-access memory (RAM) to store the current configuration file and other important data collected by the router. This data includes the IP routing table and buffer information. Buffers temporarily store packets before they are processed. All IOS processes, such as routing algorithms (OSPF or BGP, for example), also run in RAM. RAM information is lost if the router power cycles (when a router loses and regains power) or is restarted by an administrator. To view a router’s current configuration, use the show running- config IOS command. Before IOS version 10.3, administrators used the write terminal command to show a router’s configuration. The write terminal command is still valid in today’s IOS releases. Cisco IOS is hardware-specific, and the image loaded on various router platforms varies from platform to platform. For example, the image on a Cisco 4500 will not run on a Cisco 3600. Also, IOS images contain certain features, such as IPX or DES encryption. For example, you can load only IOS software that supports IP or IP plus DES encryption and so forth. Please visit the following Cisco website for more details on Cisco IOS images and platform requirements: www.cisco.com/warp/customer/130/choosing_ios.shtml. Nonvolatile RAM (NVRAM) Nonvolatile RAM (NVRAM) stores a copy of the router’s configuration file. The NVRAM storage area is retained by the router in the event of a power cycle. When the router powers up from a power cycle or a reboot (reload command), the IOS copies the stored configuration file from the NVRAM to RAM. To view the configuration file stored in NVRAM, issue the show startup-config command. In earlier versions of IOS (before version 10.3), the show config command was used to view the configuration file stored in NVRAM. In IOS versions 11.0+, both the show config and show startup-config commands will work. System Flash The System Flash is an erasable and programmable memory used to store the router’s IOS image. Although Flash memory is always limited in size, it can contain multiple versions of IOS. Therefore, you can delete, retrieve, and store new versions of IOS in the Flash memory system. To view the Flash on a Cisco router, use the show flash IOS command. Example 4-1 displays the Flash filename on a router named R1.
- 175. 152 Chapter 4: Cisco IOS Specifics and Security NOTE On a high-performance router, such as Cisco 4500 series and 7500 series routers, you can make the Flash system look like a file system and store many versions of IOS. The IOS command to partition the System Flash is partition flash number-of-partition size-of-each-partition. Example 4-1 show flash Command R1>show flash System flash directory: File Length Name/status 1 9558976 c2500-ajs40-l.12-17.bin [9559040 bytes used, 7218176 available, 16777216 total] 16384K bytes of processor board System flash Example 4-1 shows that the IOS image, c2500-ajs40-l.12-17.bin, is currently stored on the router’s on-board System Flash. The Cisco 7500 series router provides the option of installing additional PCMCIA Flash memory. If this additional memory is installed, the dir slot0: IOS command displays the IOS image stored in slot0. NOTE The IOS image’s name conveys a lot of information, including the platform and feature sets. For more information, go to www.cisco.com and search for “software naming convention.” Central Processing Unit The central processing unit (CPU) is the heart of a router, and every Cisco router has a CPU. A CPU manages all the router’s processes, such as IP routing, and new routing entries, such as remote IP networks learned through a dynamic routing protocol. To view a CPU’s status, use the show process IOS command. Example 4-2 shows a sample display taken from a Cisco IOS router. Example 4-2 (Truncated) show process Command R1>show process CPU utilization for five seconds: 9%/7%; one minute: 9%; five minutes: 10% PID QTy PC Runtime (ms) Invoked uSecs Stacks TTY Proc 1 Csp 318F396 24456 1043 234 732/1000 0 Load Meter 2 M* 0 28 28 1000 3268/4000 0 EXEC 3 Lst 317D1FC 1304 175 5257 1724/2000 0 Check heap ...
- 176. Cisco Hardware 153 The show process command displays the router utilization within the past five seconds, the past one minute, as well as the average over the last five minutes. Details about specific processes follow the CPU utilization statistics. Read-Only Memory Read-only memory (ROM) stores a scaled-down version of a router’s IOS in the event that the Flash system becomes corrupted or no current IOS image is stored in Flash. ROM also contains the bootstrap program (sometimes referred to as the rxboot image in Cisco documentation) and a device’s power up diagnostics. You can perform only a software upgrade (that is, perform a software image upgrade on the ROM) by replacing ROM chips because the ROM is not programmable. The bootstrap program enables you to isolate or rule out hardware issues. For example, you might have a faulty Flash card and, subsequently, the router cannot boot the IOS image. The power diagnostics program tests all the hardware interfaces on the router. ROM mode contains a limited number of IOS commands, which enables the administrator or the Technical Assis- tance Center (TAC) to help troubleshoot and ascertain any hardware or configuration issues on a Cisco router. Cisco TAC is available 24 hours a day, seven days a week. You must pay Cisco for this service and have a valid contract number to open any cases. Unfortunately, not all Cisco routers have the same ROM code, so the commands might vary but the principle remains the same. You can always issue the ? command in ROM mode to identify the available commands used to troubleshoot a Cisco IOS-based router. Newer Cisco hardware models now contain a new boot program stored in Boot Flash rather than in the ROM. The program is a little more user-friendly. Menu-driven options are available to change the configuration register, for example. Example 4-3 provides all the available options on a Cisco 4000 router when the ? command is used in ROM mode. Example 4-3 ? Command When in ROM Mode > ? ? Types this display $ Toggle cache state B [filename] [TFTP Server IP address | TFTP Server Name] Load and excutute system image from ROM or from TFTP server C [address] Continue [optional address] D /S M L V Deposit value V of size S into location L with modifier M E /S M L Examine location L with size S with modifier M G [address] Begin execution H Help for commands I Initialize K Displays Stack trace L [filename] [TFTP Server IP address | TFTP Server Name] continues
- 177. 154 Chapter 4: Cisco IOS Specifics and Security Example 4-3 ? Command When in ROM Mode (Continued) Load system image from ROM or from TFTP server, but do not begin execution O Show software configuration register option settings P Set break point S Single step next instruction T function Test device (? for help) The options in Example 4-3 include the ability to initialize a router with the i command after you have finished ROM mode. ROM mode enables you to recover lost passwords by altering the configuration registers (covered later in this chapter). Configuration Registers The configuration register is a 16-bit number that defines how a router operates on a power cycle. These options include if the IOS will be loaded from Flash or ROM. Configuration registers advise the CPU to load the configuration file from the NVRAM or to ignore the configuration file stored in memory, for example. The default configuration register is displayed as 0x2102. Table 4-1 displays the binary conversion from 0x2102. Table 4-1 0x2102 Binary Conversion Bit Number Value 15 0 14 0 13 1 12 0 11 0 10 0 9 0 8 1 7 0 6 0 5 0 4 0 3 0 2 0 1 1 0 0
- 178. Cisco Hardware 155 The bits are numbered from right to left. In the preceding example, the value is displayed as 0x2102 (0010.0001.0000.0010). The function of the configuration register bits is determined by their position, as follows: • Bits 0 through 3—Determines the boot option whether the router loads the IOS from the Flash (binary value is 010) or from ROM (binary value is 000). • Bit 4—Reserved. • Bit 5—Reserved. • Bit 6—Tells the router to load the configuration from NVRAM if set to 1 and to ignore the NVRAM if set to 0. • Bit 7— Referred to as the OEM (OEM = original equipment manufacturer) bit in Cisco documentation and is not used. • Bit 8—Specifies whether to enter ROM mode without power cycling the router. If bit 8 is set to 1 and the break key is issued while the router is up and running normally, the router will go into ROM mode. This is a dangerous scenario because if this occurs, your router immediately stops functioning. • Bit 9—Reserved. • Bit 10—Specifies the broadcast address to use, where 1 equals the use of all 0s for broadcast at boot (in conjunction with bit 14). Bit 10 interacts with bit 14. • Bits 11 and 12—Set the console port’s baud rate. For example, if bits 11 and 12 are set to 00, the baud rate is 9600 bps. A baud rate of 4800 bps can be set when these bits are set to 01. 10 sets the baud rate to 2400 bps, and 11 sets the baud rate to 1200 bps. • Bit 13—Tells the router to boot from ROM if the Flash cannot boot from a network, such as a TFTP server. If bit 13 is set to 0 and no IOS is found, the router will hang. If bit 13 is set to 1 and no IOS is found, the router boots from ROM. • Bit 14—Interacts with Bit 10 to define broadcast address. • Bit 15—Specifies to enable diagnostics display on startup and ignore the NVRAM. To view the current configuration register, use the show version IOS command. Example 4-4 displays the configuration register of a router, R1. Example 4-4 (Truncated) show version Command R1>show version Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-AJS40-L), Version 11.2(17) , RELEASE SOFTWARE (fc1) Copyright (c) 1986-1999 by Cisco Systems, Inc. Compiled Tue 05-Jan-99 13:27 by ashah Image text-base: 0x030481E0, data-base: 0x00001000 ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE continues
- 179. 156 Chapter 4: Cisco IOS Specifics and Security Example 4-4 (Truncated) show version Command (Continued) BOOTFLASH: 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a), RELEASE SOFTWARE R1 uptime is 6 days, 1 hour, 36 minutes System restarted by reload System image file is "flash:c2500-ajs40-l.112-17.bin", .. ..booted via flash cisco 2520 (68030) processor (revision E) with 8192K/2048K byte Processor board ID 02956210, with hardware revision 00000002 Bridging software. SuperLAT software copyright 1990 by Meridian Technology Corp. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. TN3270 Emulation software. Basic Rate ISDN software, Version 1.0. 1 Ethernet/IEEE 802.3 interface(s) 2 Serial network interface(s) 2 Low-speed serial(sync/async) network interface(s) 1 ISDN Basic Rate interface(s) 32K bytes of non-volatile configuration memory. 16384K bytes of processor board System flash (Read ONLY) Configuration register is 0x2102 The output from Example 4-4 displays the configuration register as 0x2102. The show version command also displays other useful router information, such as the router’s uptime, the IOS image in use, and the hardware configuration. To change the configuration register, use the global configuration command, configure-register register-value. When a configuration register is changed, use the show version command to ensure that the register has been changed to the new value. Table 4-2 displays common configuration register values you can use in day-to-day troubleshooting of Cisco IOS routers. Table 4-2 Common Registers and Descriptions Register Value Description 0x2100 Boots the router using the system bootstrap found in ROM. 0x2102 Boots the router using Flash and NVRAM. This is the default setting. 0x2142 Boots the router using Flash and ignores NVRAM. This value is used to recover passwords or modify configuration parameters. Cisco Interfaces Interfaces provide connections to a network. Interfaces include LANs, WANs, and management ports (that is, console and auxiliary ports).
- 180. Cisco Hardware 157 To view the current LAN or WAN interface, issue the show interface command. The show interface command displays all LAN and WAN interfaces. To display information regarding console or auxiliary ports, use the show line command. Figure 4-2 summarizes the available IOS commands that administrators can use to view a router’s current configuration. Figure 4-2 Interface IOS Commands show flash show startup-config dir slot0. show config show running-config write terminal Random-Access Memory (RAM) Flash Read-Only Nonvolatile RAM Memory (ROM) (NVRAM) LAN, WAN, Router Interfaces Console, AUX Port show interfaces Now that you have reviewed Cisco routers’ hardware basics, it’s time to review how routers operate. In addition to router operation, this chapter covers how administrators can manage Cisco routers by saving and loading files to and from a TFTP server. NOTE Cisco routers can operate in a number of modes. Cisco defines them as follows: • ROM boot mode—When the router is in boot mode and loaded with a subset of the IOS image, only a limited number of commands are available. • Configuration mode—Where you can make configuration changes. An example prompt is Router1(config)#. • Interface configuration mode—Where you make configuration changes to interfaces such as the Ethernet or Serial connections. Example prompt is Router1(config-if)#. • Initial configuration mode—When a router first boots up out of the box with no initial configuration, you are prompted for basic system configuration details, such as name and IP address assignment. The prompt looks like this: Would you like to answer the initial configuration dialog? [yes/no]
- 181. 158 Chapter 4: Cisco IOS Specifics and Security • User EXEC mode—Basic IOS commands are permitted from the command-line interface (CLI). An example prompt is R1>. • Privileged EXEC mode (also referred to as enabled mode)—Advance IOS commands are permitted when the enable password or secret password is entered from the CLI. An example prompt is R1#. Saving and Loading Files The configuration file can reside on the router’s NVRAM, RAM, or on a TFTP server. When a router boots with the default configuration register (0x2102), the configuration file is copied from NVRAM to RAM. Network administrators typically save the configuration files to a TFTP server as a backup, in case of a router failure. To save a configuration file from RAM to NVRAM (after configuration changes are made), the IOS command is copy running-config startup-config. The write terminal command will also copy the running configuration to startup configuration. The write command is a legacy com- mand from earlier releases of IOS still valid in today’s versions of IOS software. Example 4-5 displays a successful configuration change on Ethernet 0/0, followed by a network administrator in PRIV EXEC (privilege EXEC mode) mode saving the new configuration file to NVRAM. Example 4-5 Saving IOS Configurations Files R1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. R1(config)#interface ethernet 0/0 R1(config-if)#ip address 131.108.1.1 255.255.255.0 R1(config-if)#exit R1#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] R1# Table 4-3 summarizes the configuration file manipulation that can be performed on Cisco IOS routers.
- 182. show and debug Commands 159 Table 4-3 Cisco IOS File Manipulations IOS Command Meaning copy running-config startup-config Copies the configuration file from RAM to NVRAM. write memory Copies the running configuration to NVRAM. (Superseded by the new command, copy running-config startup-config.) copy startup-config running-config Copies the configuration file from NVRAM to RAM. write terminal Displays the current configuration file in RAM. (Superseded by the new command, show running-config.) show config Displays the current configuration file in NVRAM. (Superseded by the new command, show startup-config.) copy running-config tftp Copies the configuration file stored in RAM to a TFTP server. Can also be copied to an FTP or RCP server. copy tftp running-config Copies a configuration file from a TFTP server to the running configuration. show and debug Commands Cisco IOS CLI has an enormous amount of show and debug commands available to the privileged EXEC user. This section covers the show and debug commands most often used to manage Cisco IOS devices. Router CLI Cisco IOS routers allow network administrators access to a wide range of show and debug commands. The show command displays various information about the router’s state of play, such as the Ethernet collisions on a particular interface or a router’s configuration file. Only a subset of show commands is available when in User EXEC mode. The full range is available when in privilege EXEC mode (PRIV EXEC mode). The debug command is a more advanced IOS command that allows the administrator to view the router’s analyses of packets or buffering mechanisms and is used only to troubleshoot a device or complete network. The debug command is very CPU-intensive. show Commands The best method to appreciate the use of show commands is to display sample output from a Cisco IOS router.
- 183. 160 Chapter 4: Cisco IOS Specifics and Security Example 4-6 displays a list of truncated show commands available from the CLI on a Cisco router in PRIV EXEC mode. Example 4-6 show Commands R1#show ? access-expression List access expression access-lists List access lists accounting Accounting data for active sessions adjacency Adjacent nodes aliases Display alias commands arp ARP table async Information on terminal lines used as router interfaces backup Backup status bgp BGP information bridge Bridge Forwarding/Filtering Database [verbose] buffers Buffer pool statistics caller Display information about dialup connections cef Cisco Express Forwarding class-map Show QoS Class Map clock Display the system clock configuration Contents of Non-Volatile memory connection Show Connection context Show context information controllers Interface controller status cops COPS information crypto Encryption module debugging State of each debugging option derived-config Derived operating configuration dhcp Dynamic Host Configuration Protocol status diag Show diagnostic information for port adapters/modules dial-peer Dial Plan Mapping Table for, e.g. VoIP Peers dialer Dialer parameters and statistics dialplan Voice telephony dial plan diffserv Differentiated services dlsw Data Link Switching information dnsix Shows Dnsix/DMDP information docsis Show DOCSIS drip DRiP DB dspu Display DSPU information dxi atm-dxi information entry Queued terminal entries environment Environmental monitor statistics exception exception informations file Show filesystem information flash: display information about flash: file system frame-relay Frame-Relay information fras FRAS Information fras-host FRAS Host Information gateway Show status of gateway history Display the session command history
- 184. show and debug Commands 161 Example 4-6 show Commands (Continued) hosts IP domain-name, lookup style, nameservers, and host table html HTML helper commands idb List of Hardware Interface Descriptor Blocks interfaces Interface status and configuration ip IP information (show ip route follows) ipv6 IPv6 information key Key information line TTY line information llc2 IBM LLC2 circuit information lnm IBM LAN manager local-ack Local Acknowledgement virtual circuits location Display the system location logging Show the contents of logging buffers memory Memory statistics mgcp Display Media Gateway Control Protocol information microcode show configured microcode for downloadable hardware modemcap Show Modem Capabilities database mpoa MPOA show commands ncia Native Client Interface Architecture netbios-cache NetBIOS name cache contents ntp Network time protocol num-exp Number Expansion (Speed Dial) information parser Display parser information pas Port Adaptor Information pci PCI Information policy-map Show QoS Policy Map ppp PPP parameters and statistics printers Show LPD printer information privilege Show current privilege level processes Active process statistics protocols Active network routing protocols registry Function registry information reload Scheduled reload information rmon rmon statistics route-map route-map information running-config Current operating configuration sessions Information about Telnet connections sgbp SGBP group information snmp snmp statistics spanning-tree Spanning tree topology srcp Display SRCP Protocol information ssh Status of SSH server connections ssl Show SSL command stacks Process stack utilization standby Hot standby protocol information startup-config Contents of startup configuration tcp Status of TCP connections tech-support Show system information for Tech-Support terminal Display terminal configuration parameters traffic-shape traffic rate shaping configuration continues
- 185. 162 Chapter 4: Cisco IOS Specifics and Security Example 4-6 show Commands (Continued) users Display information about terminal lines version System hardware and software status vlans Virtual LANs Information vtemplate Virtual Template interface information whoami Info on current tty line This section briefly covers the highlighted commands in Example 4-6. Example 4-7 displays sample output from the most widely used IOS command, show ip route. Example 4-7 show ip route Command R1#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 131.108.0.0/16 is variably subnetted, 3 subnets, 2 masks C 131.108.255.0/30 is directly connected, Serial0/0 O 131.108.2.0/24 [110/400] via 131.108.255.2, 00:00:03, Serial0/0 C 131.108.1.0/24 is directly connected, Ethernet0/0 R1#show ip route ? Hostname or A.B.C.D Network to display information about or hostname bgp Border Gateway Protocol (BGP) connected Connected egp Exterior Gateway Protocol (EGP) eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) igrp Interior Gateway Routing Protocol (IGRP) isis ISO IS-IS list IP Access list mobile Mobile routes odr On Demand stub Routes ospf Open Shortest Path First (OSPF) profile IP routing table profile rip Routing Information Protocol (RIP) static Static routes summary Summary of all routes supernets-only Show supernet entries only vrf Display routes from a VPN Routing/Forwarding instance | Output modifiers <cr> R1#show ip route ospf 131.108.0.0/16 is variably subnetted, 3 subnets, 2 masks O 131.108.2.0/24 [110/400] via 131.108.255.2, 00:00:30, Serial0/0 R1#
- 186. show and debug Commands 163 Example 4-7 displays three IP routing entries. The more specific command, show ip route ospf, only displays remote OSPF entries. Every IOS command can be used with the ? character to display more options. In this case, the network administer used it to identify the ospf option and then typed show ip route ospf to view only remote OSPF entries. Example 4-8 displays the output from the show ip access-lists IOS command. Example 4-8 show ip access-lists R1#show ip access-lists ? <1-199> Access list number <1300-2699> Access list number (expanded range) WORD Access list name | Output modifiers <cr> R1#show ip access-lists Standard IP access list 1 permit 131.108.0.0, wildcard bits 0.0.255.255 Extended IP access list 100 permit tcp any host 131.108.1.1 eq telnet Example 4-8 enables the network administrator to quickly verify any defined access lists. Example 4-8 includes two access lists numbered 1 and 100. Use the show debugging command to display any debug commands in use. This verifies if any debugging is currently enabled. Example 4-9 displays the sample output when debug ip routing is enabled. Example 4-9 show debugging Command R1#show debugging show IP routing: IP routing debugging is on R1#undebug all All possible debugging has been turned off Currently, the router in Example 4-9 is enabled for debugging IP routing. To turn off the debugging, apply the undebug all command, as shown in Example 4-9. This command ensures all debug options are disabled. You can specify the exact debug option you want to disable with the no options; for example, to disable the IP packet option, the IOS command is no debug ip packet. To display the hardware interfaces on the router, use the show interfaces command to explore the physical and statistical state.
- 187. 164 Chapter 4: Cisco IOS Specifics and Security Example 4-10 displays the show interfaces command on a router named R1. Example 4-10 show interfaces R1#show interfaces Ethernet0/0 is up, line protocol is up --physical status Hardware is AmdP2, address is 0002.b9ad.5ae0 (bia 0002.b9ad.5ae0) Internet address is 131.108.1.1/24 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:01, output hang never Last clearing of "show interface" counters 00:00:05 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 1 packets input, 366 bytes, 0 no buffer Received 1 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with dribble condition detected 3 packets output, 202 bytes, 0 underruns(0/0/0) 0 output errors, 0 collisions, 0 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Serial0/0 is up, line protocol is up Hardware is PowerQUICC Serial Internet address is 131.108.255.1/30 MTU 1500 bytes, BW 256 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY, loopback not set Keepalive set (10 sec) LMI enq sent 0, LMI stat recvd 0, LMI upd recvd 0, DTE LMI up LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0 LMI DLCI 0 LMI type is ANSI Annex D frame relay DTE Broadcast queue 0/64, broadcasts sent/dropped 1/0, interface broadcasts 1 Last input 00:00:02, output 00:00:00, output hang never Last clearing of "show interface" counters 00:00:07 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 192 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 2 packets input, 86 bytes, 0 no buffer
- 188. show and debug Commands 165 Example 4-10 show interfaces (Continued) Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 2 packets output, 86 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up Ethernet0/1 is administratively down, line protocol is down Hardware is AmdP2, address is 0002.b9ad.5ae1 (bia 0002.b9ad.5ae1) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters 00:00:10 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with dribble condition detected 0 packets output, 0 bytes, 0 underruns(0/0/0) 0 output errors, 0 collisions, 0 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Example 4-10 displays a router with two Ethernet interfaces and one serial interface. Interface Ethernet 0/0 is enabled and is currently running packets over the wire, while Ethernet 0/1 is not enabled. Interface Serial 0/0 is configured for Frame Relay and the physical layer (Layer 1) details are displayed. Other possible physical states are as follows: Ethernet0/1 is up, line protocol is up—The Ethernet Interface is active, sending and receiving Ethernet frames. Ethernet0/1 is up, line protocol is down—The Ethernet Interface is cabled but no keepalives are received, and no Ethernet frames are sent or received (possible cable fault). Ethernet0/1 is administratively down, line protocol is down—Ethernet Interface is not enabled administratively; typically an interface not configured as yet. Ethernet 0/1 is down, line protocol is up—A physical condition is not possible, for example.
- 189. 166 Chapter 4: Cisco IOS Specifics and Security To display the system log (syslog), use the show logging command. Example 4-11 displays a sample output taken from a router name R1. Example 4-11 show logging Command R1#show logging Syslog logging: enabled (0 messages dropped, 0 messages rate-limited, 0 flushes, 0 overruns) Console logging: level debugging, 27 messages logged Monitor logging: level debugging, 0 messages logged Buffer logging: level debugging, 1 messages logged Logging Exception size (4096 bytes) Trap logging: level debugging, 31 message lines logged debugging Log Buffer (60000 bytes): 2d20h: %SYS-5-CONFIG_I: Configured from console by console 2d20h: %CLEAR-5-COUNTERS: Clear counter on all interfaces by console Example 4-11 shows that 27 message have been logged and the logging level is debugging, which entails the following log message types: • Emergencies—System is unusable (severity = 0) • Alerts—Immediate action needed (severity = 1) • Critical—Critical conditions (severity = 2) • Errors—Error conditions (severity = 3) • Warnings—Warning conditions (severity = 4) • Notifications—Normal but significant conditions (severity = 5) • Informational—Informational messages (severity = 6) • Debugging—Debugging messages (severity = 7) Two messages have also been displayed on the terminal: the first message is a configuration change, and the second appears when a PRIV EXEC user cleared the counters on all the interfaces. The show route-map command displays any policy route maps configured. Policy route maps override routing decisions on Cisco routers. Route maps basically allow an administrator to access the route manipulation. The show version command displays the system’s hardware configuration, the software version, the names and sources of configuration files, and the boot images. Issue the show version EXEC command to accomplish this. Example 4-12 displays a sample output.
- 190. show and debug Commands 167 Example 4-12 show version Command on R1 R1#show version Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-IK8O3S-M), Version 12.2(2)T, RELEASE SOFTWARE (f c1) TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Sat 02-Jun-01 15:47 by ccai Image text-base: 0x80008088, data-base: 0x813455F8 ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1) ROM: C2600 Software (C2600-IK8O3S-M), Version 12.2(2)T, RELEASE SOFTWARE (fc1) C2600-IK8O3S-M), 12.2(2)T R1 uptime is 2 days, 20 hours, 15 minutes System returned to ROM by reload at 14:57:18 UTC Mon Mar 1 1993 System restarted at 10:00:02 UTC Mon Mar 1 1993 System image file is "flash:c2600-ik8o3s-mz.122-2.T.bin" cisco 2611 (MPC860) processor (revision 0x203) with 61440K/4096K bytes of memory Processor board ID JAD043000VK (1947766474) M860 processor: part number 0, mask 49 Bridging software. X.25 software, Version 3.0.0. 2 Ethernet/IEEE 802.3 interface(s) 32K bytes of non-volatile configuration memory. 16384K bytes of processor board System flash (Read/Write) Configuration register is 0x2102 Example 4-12 displays a number of key hardware data about the router. For example, the IOS software version is 12.2T, the router’s uptime is 2 days, 20 hours, 15 minutes, and the memory installed on the router is 64 MB. There is 16 MB of System Flash, and the current configuration register is 0x2102. NOTE The alias command creates a custom shortcut to IOS commands so the EXEC user does not have to type the complete IOS command. For example, show ip route is already defined in IOS with the shortcut sh ip ro (not an alias command but rather a shortcut command). You can define your own alias with the global IOS command: alias EXEC alias-name IOS-command View the predefined aliases with the following command: Router#show aliases EXEC mode aliases: h help lo logout p ping r resume s show u undebug un undebug w where
- 191. 168 Chapter 4: Cisco IOS Specifics and Security For example, you could make the command ospf display only OSPF routes by issuing the following command: alias EXEC ospf show ip route ospf Debugging Cisco Routers The debug command is one of the best set of tools you will encounter on Cisco routers. The debug command is available only from privilege mode. Cisco IOS router’s debugging includes hardware and software to aid in troubleshooting internal problems and problems with other hosts on the network. The debug privileged EXEC mode commands start the console display of several classes of network events. For debug output to display on a console port, you must ensure that debugging to the console has not been disabled or sent to the logging buffer with the logging console debug command. If you enable any debug commands through a console and no debug output is displayed, it might be because logging has been disabled. Check the running configuration for the line no logging debugging console, and remove this line (by typing logging debugging console) to enable debug messages to be viewed by the console port. Remember to turn off console logging when you are done troubleshooting the problem. The router will continue to send to the console even if nobody is there, tying up valuable CPU resources. On virtual lines (VTY lines), you must enable the terminal monitor command to view the debug output. You use VTY lines when you telnet to a remote Cisco router. NOTE Refer to the Cisco IOS Debug Command Reference at the following URL for the most updated debug command information: www.cisco.com/univercd/cc/td/doc/product/software/ios122/122sup/122debug/index.htm. When debugging data, you must also be aware of the switching method used by the router (for example, fast or process switches) because the CPU will use the same method when sending debug output to the console or vty line. The ip route-cache IOS command with no additional keywords enables fast switching. When debug ip packet flow is enabled, make sure you disable fast switching so you can view packet-by-packet flow through the router. Search the Cisco website for the keywords “Process” and “fast switching” for more details on switching methods. The following URL provides quality information on switching methods available on Cisco 7200 routers: www.cisco.com/en/US/customer/products/sw/iosswrel/ps1831/products_configuration_ guide_chapter09186a00800ca6c7.html#xtocid6.
- 192. show and debug Commands 169 Table 4-4 displays the debug commands and the system debug message feature. Table 4-4 debug Command Summary IOS Command Purpose show debugging Displays the state of each debugging option debug ? Displays a list and brief description of all the debug command options debug command Begins message logging for the specified debug command no debug command (or undebug all) Turns message logging off for the specified debug command or turns off all debug messages with the undebug all command Example 4-13 displays the list of debug command options covered in this section. Example 4-13 debug Command Options R1#debug ? all Enable all debugging ip IP information list Set interface or/and access list for the next debug command R1#debug ip ? audit IDS audit events auth-proxy Authentication proxy debug bgp BGP information cache IP cache operations cef IP CEF operations cgmp CGMP protocol activity dhcp Dynamic Host Configuration Protocol drp Director response protocol dvmrp DVMRP protocol activity egp EGP information eigrp IP-EIGRP information error IP error debugging flow IP Flow switching operations ftp FTP dialogue html HTML connections http HTTP connections icmp ICMP transactions igmp IGMP protocol activity igrp IGRP information inspect Stateful inspection events interface IP interface configuration changes mbgp MBGP information mcache IP multicast cache operations mhbeat IP multicast heartbeat monitoring mobile IP Mobility continues
- 193. 170 Chapter 4: Cisco IOS Specifics and Security Example 4-13 debug Command Options (Continued) mpacket IP multicast packet debugging mrm IP Multicast Routing Monitor mrouting IP multicast routing table activity msdp Multicast Source Discovery Protocol (MSDP) mtag IP multicast tagswitching activity nat NAT events nbar StILE - traffic classification Engine ospf OSPF information packet General IP debugging and IPSO security transactions peer IP peer address activity pim PIM protocol activity policy Policy routing postoffice PostOffice audit events rgmp RGMP protocol activity rip RIP protocol transactions routing Routing table events rsvp RSVP protocol activity rtp RTP information scp Secure Copy sd Session Directory (SD) security IP security options socket Socket event ssh Incoming ssh connections tcp TCP information tempacl IP temporary ACL trigger-authentication Trigger authentication udp UDP based transactions urd URL RenDezvous (URD) wccp WCCP information This section covers the debug commands highlighted in Example 4-13. CAUTION The CPU system on Cisco routers gives the highest priority to debugging output. For this reason, debugging commands should be turned on only for troubleshooting specific problems or during troubleshooting sessions with technical support personnel. Excessive debugging output can render the system inoperable. Try to use the most specific debug command possible to reduce the load on the CPU. For example, the debug all command will surely disable a router. You should use only the debug all command in a lab environment. Typically, the console port is used for debugging major faults because the CPU places debugging messages to the console port as the highest priority. Sometimes, debugging messages can overwhelm a network administrator’s ability to monitor the router, and the IOS command, logging synchronous, can limit the messages to the console.
- 194. show and debug Commands 171 When synchronous logging of unsolicited messages and debug output is turned on (the line console is configured with the logging synchronous IOS command), unsolicited Cisco IOS Software output is displayed on the console or printed after solicited Cisco IOS Software output is displayed or printed. Unsolicited messages and debug output is displayed on the console after the prompt for user input is returned. This keeps unsolicited messages and debug output from being interspersed with solicited software output and prompts. After the unsolicited messages are displayed, the console displays the user prompt again. The IOS commands logging trap can be used to limit the logging of error messages sent to syslog servers to only those messages at the specified level (levels range from 0 to 7). The lowest level is 7 (debugging messages, greatest level of messages, as level 7 encompasses all levels possible from 0 to 7), and the highest level is 0, or emergencies (system is unusable). The debug all command turns on all possible debug options available to a Cisco router. This will crash any router in a busy IP network, so we strongly recommended that you never apply this command in a working network environment. Example 4-14 displays the options when enabling IP packets through a Cisco router. Example 4-14 debug ip packet ? R1#debug ip packet ? <1-199> Access list <1300-2699> Access list (expanded range) detail Print more debugging detail <cr> You can define an access list so that only packets that satisfy the access list are sent through to the console or vty line. Figure 4-3 displays a typical example where Simon, a user on one Ethernet (Ethernet 0/0), is advising you that packets from users on Ethernet 0/1 (Melanie’s PC) are not reaching each other. To view the routing packet flow through Router R1, you can debug the IP packets and use a standard access list or an extended one (access lists are covered later in this chapter). To view the IP packet flow and ensure that you view only packets from Melanie’s PC to Simon’s PC, you can define an extended access list matching the source address, 131.108.2.100 (Melanie’s PC), to the destination address, 131.108.1.100 (Simon’s PC).
- 195. 172 Chapter 4: Cisco IOS Specifics and Security Figure 4-3 IP Data Flow from One Segment to Another Users Report No Packet Flow Application Layer Errors Application Layer Errors 131.108.1.100/24 131.108.2.100/24 R1 E0/0 E0/1 User Simon User Melanie interface Ethernet0/0 ip address 131.108.1.1 255.255.255.0 interface Ethernet0/1 ip address 131.108.2.1 255.255.255.0 Example 4-15 displays the debug command configuration on Router R1. Example 4-15 Enabling debug ip packet with Access-list 100 R1#config terminal Enter configuration commands, one per line. End with CNTL/Z. R1(config)#access-list 100 permit ip host 131.108.2.100 host 131.108.1.100 R1#debug ip packet ? <1-199> Access list <1300-2699> Access list (expanded range) detail Print more debugging detail <cr> R1#debug ip packet 100 ? detail Print more debugging detail <cr> R1#debug ip packet 100 detail IP packet debugging is on (detailed) for access list 100 Applying the exact debug command for only traffic generated from one device to another ensures that the router is not using too many CPU cycles to generate the debug output to the console. When a ping request is sent from Melanie’s PC to Simon’s PC, debug output displays a successful ping request. Example 4-16 displays the sample debug output matching access-list 100 when 5 ping packets are sent.
- 196. show and debug Commands 173 NOTE When debugging with a specific IP access list, be sure to stop all debugging options with the undebug all IOS command before removing IP access lists; Cisco IOS routers are prone to failure if the access list is removed before the debugging options are disabled. For example, no debug output will be captured and sent to the console if no access list is defined but referenced by a debug command (for example, debug ip packet 100, when access-list 100 is not defined). Also, remember that the default, deny not specifically permitted, is the default behavior for Cisco IOS access lists. Make sure you permit only traffic for which you are interested in viewing debug messages like the example shown in Figure 4-3. Example 4-16 Ping Request R1#ping 131.108.1.100 2d22h: IP: s=131.108.2.100 (local), d=131.108.1.100 (Ethernet0/0), len 100, sending 2d22h: ICMP type=8, code=0 2d22h: IP: s=131.108.2.100 (Ethernet0/0), d=131.108.1.100 (Ethernet0/0), len 100, rcvd 3 2d22h: ICMP type=8, code=0 2d22h: IP: s=131.108.2.100 (local), d=131.108.1.100 (Ethernet0/0), len 100, sending 2d22h: ICMP type=8, code=0 2d22h: IP: s=131.108.2.100 (Ethernet0/0), d=131.108.1.100 (Ethernet0/0), len 100, rcvd 3 2d22h: ICMP type=8, code=0 2d22h: IP: s=131.108.2.100 (local), d=131.108.1.100 (Ethernet0/0), len 100, sending 2d22h: ICMP type=8, code=0 2d22h: IP: s=131.108.2.100 (Ethernet0/0), d=131.108.1.100 (Ethernet0/0), len 100, rcvd 3 2d22h: ICMP type=8, code=0 2d22h: IP: s=131.108.2.100 (local), d=131.108.1.100 (Ethernet0/0), len 100, sending 2d22h: ICMP type=8, code=0 2d22h: IP: s=131.108.2.100 (Ethernet0/0), d=131.108.1.100 (Ethernet0/0), len 100, rcvd 3 2d22h: ICMP type=8, code=0 2d22h: IP: s=131.108.2.1 (local), d=131.108.1.1 (Ethernet0/0), len 100, sending 2d22h: ICMP type=8, code=0 2d22h: IP: s=131.108.2.100 (Ethernet0/0), d=131.108.1.100 (Ethernet0/0), len 100, rcvd 3 2d22h: ICMP type=8, code=0
- 197. 174 Chapter 4: Cisco IOS Specifics and Security The debug output demonstrates that five packets were successfully routed from Ethernet 0/1 to Ethernet 0/0. Therefore, the network fault reported by the users points to an application error rather than a network error. Table 4-5 displays the meaning of the codes in Example 4-16. Table 4-5 debug ip packet 100 detail Explanation Field Meaning IP: Indicates an IP packet s=131.108.2.100 Indicates the packet’s source address (Melanie’s PC) d=131.108.1.100 Indicates the packet’s destination address (Simon’s PC) ICMP type 8 code 0 Ping request Len 100 The length of the IP packet (100 bytes) NOTE The detail option allows for further detail in the debug output. Using the route cache is often called fast switching. The route cache allows outgoing packets to be load-balanced on a per-destination basis, rather than on a per-packet basis. NOTE The output modifier | (pipe) is a great time saver. For example, the command, show running- config | begin router ospf 100, shows only the running configuration starting from the router ospf 100 part instead of the entire output. Password Recovery Sometimes, the Cisco-enable or secret password is unknown and you must use password recovery to attain or change the enable/secret password. Password recovery allows the network administrator to recover a lost or unknown password on a Cisco router. For password recovery, an administrator must have physical access to the router through the console or auxiliary port. When an EXEC user enters an incorrect enable password, the user receives an error message similar to the message shown in Example 4-17; the password entered is Cisco which is displayed as *****.
- 198. Password Recovery 175 Example 4-17 Incorrect Password Error Message R1>enable Password: ****** Password: ***** Password: ***** % Bad passwords R1> When a user receives a % Bad passwords message, the user can neither access the advanced command set (in this case, enable mode), nor make any configuration changes. Fortunately, Cisco provides the following 10-step method to recover a lost password without losing configuration files: Step 1 Power cycle the router. Step 2 Issue a Control Break or the Break key command on the application (for Windows 2000, it is Control-Pause) to enter into boot ROM mode. The Control Break key sequence must be entered within 60 seconds of the router restarting after a power cycle. Step 3 After you are in ROM mode, change the configuration register value to ignore the startup configuration file that is stored in NVRAM. Use the o/r 0x2142 command. Step 4 Allow the router to reboot by entering the i command. Step 5 After the router has finished booting up without its startup configuration, look at the show startup-config command output. If the password is encrypted, move to Step 6, which requires you to enter the enable mode (type enable and you will not be required to enter any password) and copy the startup configuration to the running configuration with the copy startup-config running-config command. Then, change the password. If the password is not encrypted and the enable secret command is not used, simply document the plain text password and go to Step 8. Step 6 Copy the startup configuration to RAM. Step 7 Enable all active interfaces. Step 8 Change the configuration register to 0x2102 (default). Step 9 Reload the router. Step 10 Check the new password.
- 199. 176 Chapter 4: Cisco IOS Specifics and Security NOTE These are the generic steps for password recovery on a Cisco router. Some commands and steps might be slightly different depending on the hardware platform. Refer to the Password Recovery Procedures Index (www.cisco.com/warp/public/474/) for more information on each platform. To review, look at an example. Assume you are directly connected to Router R1 and you do not know the enable password. You power cycle the router and press the Control Break key (the Esc key) to enter boot mode. Example 4-18 shows the dialog displayed by the router after a break is issued. Example 4-18 Password Recovery Dialog on a Cisco Router System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE Copyright (c) 1986-1995 by cisco Systems Abort at 0x10EA882 (PC) !control break issued followed by ? to view help options >>? ------------>control break issued followed by ? to view help options $ Toggle cache state B [filename] [TFTP Server IP address | TFTP Server Name] Load and EXECute system image from ROM or from TFTP server C [address] Continue EXECution [optional address] D /S M L V Deposit value V of size S into location L with modifier M E /S M L Examine location L with size S with modifier M G [address] Begin EXECution H Help for commands I Initialize K Stack trace L [filename] [TFTP Server IP address | TFTP Server Name] Load system image from ROM or from TFTP server, but do not begin EXECution O Show configuration register option settings P Set the break point S Single step next instruction T function Test device (? for help) As you can see in Example 4-18, the ? symbol can display all the available options. To view the current configuration register, issue the e/s 2000002 command, which displays the value of the configuration register. Example 4-19 displays the current configuration register.
- 200. Password Recovery 177 Example 4-19 e/s 200002 Command in Boot Rom Mode >e/s 2000002 ! This command will display the current configuration register 2000002: 2102 ! Type q to quit > The default value for the configuration register on Cisco IOS routers is 2102. For illustrative purposes, change the register to 0x2142, which tells the IOS to ignore the configuration in NVRAM. The command to change the configuration register in Boot ROM mode is 0/r 0x2142 followed by the initialize (i) command, which will reload the router. Example 4-20 displays the configuration change and initializing of the router from boot ROM mode. Example 4-20 Changing the Configuration Register to 0x2142 >0/r 0x2142 >i The i command reboots the router and ignores your startup configuration because the configu- ration register has been set to 0x2142. The aim here is to change the password without losing your original configuration. Example 4-21 shows a truncated display by the Cisco IOS after the router is reloaded. Example 4-21 Dialog After Reload System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE Copyright (c) 1986-1995 by Cisco Systems 2500 processor with 6144 Kbytes of main memory F3: 9407656+151288+514640 at 0x3000060 Restricted Rights Legend Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-AJS40-L), Version 11.2(17) Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Tue 05-Jan-99 13:27 by ashah Image text-base: 0x030481E0, data-base: 0x00001000 Basic Rate ISDN software, Version 1.0. 1 Ethernet/IEEE 802.3 interface(s) 2 Serial network interface(s) 2 Low-speed serial(sync/async) network interface(s) 1 ISDN Basic Rate interface(s) 32K bytes of non-volatile configuration memory. 16384K bytes of processor board System flash (Read ONLY) continues
- 201. 178 Chapter 4: Cisco IOS Specifics and Security Example 4-21 Dialog After Reload (Continued) --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Would you like to enter the initial configuration dialog? [yes]:No Press RETURN to get started! ...... Router>ena !(no password required or entered) Router# Notice that the router reverts to the default configuration. Enter the enable command to enter privilege EXEC mode. In this example, you will not be prompted for the enable password because there isn’t one; by default, no enable password is configured when a Cisco IOS router boots from the default configuration (no passwords are configured in this default state). You can view the startup config by using the show startup-config command (or show config in IOS versions predating version 10.3), as shown in Example 4-22. Example 4-22 show startup-config Command Router#show startup-config Using 1968 out of 32762 bytes ! Last configuration change at 16:35:50 UTC Tue May 18 2002 ! NVRAM config last updated at 16:35:51 UTC Tue May 18 2002 version 2.2 service password-encryption hostname R1 ! Note there is no secret password either enable password 7 05080F1C2243 ... As you can see in Example 4-22, the enable password is encrypted. In instances where the password is not encrypted, you could view the password using the show startup-config command. When a password is encrypted, you must copy the startup configuration to the running configuration and change the password manually by using the following IOS command: copy startup-config running-config At this point, you are still in privileged mode, so you can now enter global configuration mode to change the password back to its original setting (cisco, in this instance). Example 4-23 displays the password change in global configuration mode set to the new password of cisco.
- 202. Basic Security on Cisco Routers 179 Example 4-23 Changing a Password and Setting the Configuration Registry Commands hostname#copy startup-config running-config Destination filename [running-config]? 2818 bytes copied in 1.475 secs (2818 bytes/sec) R1#config terminal R1(config)#enable password cisco R1(config)#config-register 0x2102 R1(config)#exit R1#reload You complete password recovery by changing the configuration register back to the default value (0x2102). NOTE If a secret password is also configured, you must use the enable secret password IOS command because the secret password overrides the enable password. Example 4-23 includes no secret password, so you can use the enable password command. When the Cisco IOS router reloads, it will load the new configuration file with the password set to cisco. Basic Security on Cisco Routers You can access a Cisco router in a number of ways. You can physically access a router through the console port, or you can access a router remotely through a modem via the auxiliary port. You can also access a router through a network or virtual terminal ports (VTY lines), which allow remote Telnet access. If you do not have physical access to a router—either through a console port or an auxiliary port via dialup—you can access a router through the software interface, called the virtual terminal (also referred to as a VTY port). When you telnet to a router, you might be required to enter the VTY password set by the network administrator. For example, on Router R1, the administrator types R2’s remote address and tries to telnet to one of the VTY lines. Example 4-24 provides the session dialog when a user telnets to the router with the IP address 131.108.1.2. Example 4-24 Using a VTY Port to Establish a Telnet Connection R1#Telnet 131.108.1.2 Trying 131.108.1.2 ... Open User Access Verification Password: xxxxx R2>
- 203. 180 Chapter 4: Cisco IOS Specifics and Security Cisco routers can have passwords set on all operation modes, including the console port, privilege mode, and virtual terminal access. To set a console password to prevent unauthorized console access to the router, issue the commands shown in Example 4-25. NOTE All passwords are case-sensitive. Example 4-25 Setting a Console Password R1(config)#line con 0 R1(config-line)#password cisco !You can also set a password on the auxiliary port R1(config)#line aux 0 R1(config-line)#password cisco To set the privilege mode password, you have two options: the enable and secret password. To set these passwords, use the respective commands listed in Example 4-26. Example 4-26 Setting Enable and Secret Password R1(config)#enable password cisco R1(config)#enable secret ccie The command to set an enable password is enable password password. You can also set a more secure password, called a secret password, which is encrypted when viewing the configuration with the enable secret password command. The secret password IOS command overrides the enable password. Cisco IOS does not permit you to configure the same password if you apply both commands. In Example 4-26, the secret password will always be used. Now, issue the show running-config command to display the configuration after entering the enable and secret passwords in Example 4-26. Example 4-27 displays the output from the show running-config IOS command after entering enable and secret passwords. Example 4-27 show running-config Command on R1 R1#show running-config Building configuration Current configuration: ! version 12.2
- 204. Basic Security on Cisco Routers 181 Example 4-27 show running-config Command on R1 (Continued) ! hostname R1 ! enable secret 5 $1$Aiy2$GGSCYdG57PdRiNg/.D.XI. enable password cisco Example 4-27 shows that the secret password is encrypted (using Cisco’s proprietary algo- rithm), while the enable password is readable. This setup enables you to hide secret passwords when the configuration is viewed. If you want, you can also encrypt the enable password by issuing the service password-encryption command, as displayed in Example 4-28. Cisco uses the MD5 algorithm to hash the secret password. You cannot reverse engineer the hashed pass- word (for example, $1$Aiy2$GGSCYdG57PdRiNg/.D.XI.). Example 4-28 service password-encryption Command R1(config)#service password-encryption service The service password-encryption command encrypts all passwords issued to the router using the MD5 encryption algorithm. Example 4-29 shows an example of how these passwords appear when the configuration is viewed after all passwords have been encrypted. Example 4-29 displays the show running-config command output after encrypting all passwords. Example 4-29 show running-config Command on R1 After Encrypting All Passwords R1#show running-config Building configuration... Current configuration: ! service password-encryption version 11.2 hostname R1 ! enable secret 5 $1$Aiy2$GGSCYdG57PdRiNg/.D.XI. enable password 7 0822455D0A16 NOTE Note the digits, 5 and 7, before the encrypted passwords. The number 5 signifies that MD5 Hash algorithm is used for encryption, whereas the number 7 signifies a weaker algorithm. You are not expected to know this for the written exam, but it is valuable knowledge for troubleshooting complex networks. In fact, a great network engineer is measured by his well-defined trouble- shooting techniques, and not by how many CCIE lab exams he has passed.
- 205. 182 Chapter 4: Cisco IOS Specifics and Security Notice in Example 4-29 that both the secret and enable passwords are encrypted. If you enable the service password-encryption command in global configuration mode, all passwords will be encrypted and will not be viewable when displaying the configuration on the Cisco router. The final Cisco password you can set is the virtual terminal password. This password verifies remote Telnet sessions to a router. Example 4-30 displays the commands necessary to set the virtual terminal password on a Cisco router. Example 4-30 password Command to Set a Virtual Terminal Password to ccie R4(config)#line vty 0 4 R4(config-line)#password ccie If you issue the no login command below the virtual terminal command (line vty 0 4), remote Telnet users will not be asked to supply a password and will automatically enter EXEC mode. Example 4-31 displays the Telnet session dialogue when the no login command is entered. Example 4-31 Dialogue Display When No Login Is Enabled R1#telnet 1.1.1.1 Trying 1.1.1.1 ... Open R2> Keep in mind that the preceding setup is not a secure access method for a router network. IP Access Lists Standard and extended access lists filter IP traffic. An access list is basically a set of permit or deny statements. Standard access lists control IP traffic based on the source address only. Extended access lists can filter on source and destination addresses. Extended access lists can also filter on specific protocols and port numbers. This section covers how a Cisco router handles access lists. Access Lists on Cisco Routers By default, a Cisco router permits all IP and TCP traffic unless an access list is defined and applied to the appropriate interface. Figure 4-4 illustrates the steps taken if an access list is configured on a Cisco router.
- 206. IP Access Lists 183 Figure 4-4 Access List Decision Taken by a Cisco Router Bit Bucket Drop Packet No Incoming IP Packet Access Yes Is Yes list packet Process configured? permitted? IP Packet No Process IP Packet If an incoming IP packet is received on a router and no access list is defined, the packet is forwarded to the IP routing software. If an access list is defined and applied, the packet is checked against the access list, and the appropriate permit or deny action is taken. The default action taken by any access list is to permit any explicitly defined statements and explicitly deny everything else. You will not see the explicitly deny statement when you issue the show ip access-lists because that is the default behavior. NOTE If the keyword out or in is not applied by the administrator when defining an IP filter on an interface, the default action is to apply the filter on the outbound traffic. Standard IP access lists range from 1 through 99 and 1300 through 1999. Extended IP access lists range from 100 through 199 and 2000 through 2699.
- 207. 184 Chapter 4: Cisco IOS Specifics and Security Standard IP access lists filter on the source address only. The Cisco IOS syntax is as follows: access-list access-list-number {deny | permit} [source-address] [source-wildcard] Table 4-6 describes the purpose of each field. Table 4-6 Standard IP access-list Command Syntax Description Command Field Description access-list-number A number from 1 through 99 that defines a standard access list number. Versions of IOS 12.0 or later also have standard access lists ranging from 1300-1999. deny IP packet is denied if a match is found. permit IP packet is permitted if it matches the criteria, as defined by the administrator. source-address Source IP address or network. Any source address can be applied by using the keyword any. source-wildcard (optional) Wildcard mask that is to be applied to the source address. This is an inverse mask, which is further explained with a few examples later in this section. The default is 0.0.0.0, which specifies an exact match. After creating the access list as described in Table 4-6, you must apply the access list to the required interface using the following command: ip access-group {access-list-number | name} {in | out} Table 4-7 describes the purpose of each field. Table 4-7 ip access-group Command Syntax Description Command Field Description access-list-number A number in the range from 1 through 99 and 1300 through 1999 that defines a standard access list number. name If you are using named access lists, that name will be referenced here. in Keyword that designates the access list as an inbound packet filter. out Keyword that designates the access list as an outbound packet filter. This is the default action. The wildcard mask previously mentioned in the access-list command matches the source address. When the wildcard mask is set to binary 0, the corresponding bit field must match; if it is set to binary 1, the router does not care to match any bit or it is an insignificant bit. For example, the mask 0.0.255.255 means that the first two octets must match, but the last two octets do not need to match—hence, the commonly used phrases care bits (0s) and don’t care bits (1s).
- 208. IP Access Lists 185 For further clarification, look at some examples of using access lists. Suppose you have found a faulty NIC card with the address 141.108.1.99/24. You have been asked to stop packets from being sent out Serial 0 on your router but to permit everyone else. In this situation, you need to deny the host address 141.108.1.99 and permit all other host devices. Example 4-32 displays the access list that fulfills this requirement. Example 4-32 Access List Configuration access-list 1 deny 141.108.1.99 0.0.0.0 access-list 1 permit 141.108.1.0 0.0.0.255 Next, you would apply the access list to filter outbound (the keyword out is supplied) IP packets on the Serial 0 interface. Example 4-33 applies the access list number 1 to the Serial interface (outbound packets). You can be a little wiser and filter the incoming packets on the Ethernet interface. This ensures that the packet is immediately dropped before it is processed by the CPU for delivery over the serial interface. Both examples are displayed in Example 4-33. Example 4-33 Applying the Access-list Interface Ethernet0 ip access-group 1 in interface Serial 0 ip access-group 1 out Now look at a more complex example of using a standard access list. Suppose you have 16 networks ranging from 141.108.1.0 to 141.108.16.0, as shown in Figure 4-5. You have assigned even subnets (2, 4, 6, 8, 10, 12, 14, and 16) to the Accounting department and odd subnets (1, 3, 5, 7, 9, 11, 13, and 15) to the Sales department. You do not want the Sales department to access the Internet, as shown in Figure 4-5. To solve this issue, you configure a standard access list. Figure 4-5 displays a simple requirement to block all odd networks from accessing the Internet. You could configure the router to deny all the odd networks, but that would require many configuration lines. NOTE Access lists are CPU-process-intensive because the router has to go through every entry in the access list for each packet until a match is made. If you want to determine the actual effect an access list has on your router, compare the CPU processes before and after activating an access list. Remember to check on a regular basis to see the big picture.
- 209. 186 Chapter 4: Cisco IOS Specifics and Security Figure 4-5 Standard Access List Example Sales Department Ethernet 141.108.1.0 segment 141.108.3.0 141.108.5.0 Block Odd 141.108.7.0 Access to Networks 141.108.9.0 Internet 141.108.11.0 141.108.13.0 141.108.15.0 Serial0/0 Internet 141.108.2.0 141.108.4.0 141.108.6.0 Even 141.108.8.0 Networks 141.108.10.0 141.108.12.0 141.108.14.0 141.108.16.0 Accounting Department access-list permit 141.108.2.0 0.0.254.255 Instead, permit only even networks (2, 4, 6, 8, 10, 12, 14, and 16) with one IOS configuration line. To accomplish this, convert all networks to binary to see if there is any pattern that you can use in the wildcard mask. Table 4-8 displays numbers 1 through 16 in both decimal and binary format. Table 4-8 Example Calculation of Numbers in Binary Decimal Binary 1 00000001 2 00000010 0 3 00000011 4 00000100 0 5 00000101 6 00000110 0 7 00000111 8 00001000 0
- 210. IP Access Lists 187 Table 4-8 Example Calculation of Numbers in Binary (Continued) Decimal Binary 9 00001001 10 00001010 0 11 00001011 12 00001100 0 13 00001101 14 00001110 0 15 00001111 16 00010000 0 Notice that odd networks always end in the binary value of 1, and even networks end with 0. Therefore, you can apply your access lists to match on the even network and implicitly deny everything else. Even numbers will always end in binary 0. You do not care about the first seven bits, but you must have the last bit set to 0. The wildcard mask that applies this condition is 111111110 (1 is don’t care and 0 is must match; the first 7 bits are set to 1, and the last bit is set to 0). This converts to a decimal value of 254. The following access list will permit only even networks: access-list 1 permit 141.108.2.0 0.0.254.255 The preceding access list will match networks 2, 4, 6, 8, 10, 12, 14, and 16 in the third octet. The default action is to deny everything else, so only even networks will be allowed, and odd networks are blocked by default. Next, you would apply the access list to the outbound interface. Example 4-34 describes the full configuration. Example 4-34 Applying the Access List Hostname R1 interface Serial0/0 ip access-group 1 out access-list 1 permit 141.108.2.0 0.0.254.255 Extended Access Lists Extended access lists range from 100 through 199 and 2000 through 2699. Alternatively, you can use a named access list with IOS release 12.0 or later. As mentioned earlier in this chapter, extended access lists can be applied to both source and destination addresses, as well as filter protocol types and port numbers. Look at some examples of extended access lists that allow you to filter several different types of traffic.
- 211. 188 Chapter 4: Cisco IOS Specifics and Security For Internet Control Message Protocol (ICMP), use the syntax shown in Example 4-35. Example 4-35 Access List Syntax for ICMP Traffic access-list access-list-number [dynamic dynamic-name [timeout minutes]] {deny | permit} icmp source source-wildcard destination destination-wildcard [icmp-type [icmp-code] [icmp-message] [precedence precedence] [tos tos] [log] For Internet Group Management Protocol (IGMP), use the syntax shown in Example 4-36. Example 4-36 Access List Syntax for IGMP Traffic access-list access-list-number [dynamic dynamic-name [timeout minutes]] {deny | permit} igmp source source-wildcard destination destination-wildcard [igmp-type] [precedence precedence] [tos tos] [log] For TCP, use the syntax shown in Example 4-37. Example 4-37 Access List Syntax for TCP Traffic access-list access-list-number [dynamic dynamic-name [timeout minutes]] {deny | permit} tcp source source-wildcard [operator port [port]] destination destination-wildcard [operator port [port]] [established] [precedence precedence] [tos tos] [log] For User Datagram Protocol (UDP), use the syntax shown in Example 4-38. Example 4-38 Access List Syntax for UDP Traffic access-list access-list-number [dynamic dynamic-name [timeout minutes]] {deny | permit} udp source source-wildcard [operator port [port]] destination destination-wildcard [operator port [port]] [precedence precedence] [tos tos] [log] As you can see, extended access lists have a range of options to suit any requirement. The most often used extended access list options are as follows: • access-list-number—Provides a number ranging from 100 through 199 that defines an extended access list. Also numbers ranging from 2000 through 2699. • deny—Denies access if the conditions are matched. • permit—Permits access if the conditions are matched.
- 212. IP Access Lists 189 • protocol—Specifies the protocol you are filtering. Some common options include eigrp, gre, icmp, igmp, igrp, ip, ospf, tcp, and udp. • source—Specifies the source address. • source-wildcard—Specifies the wildcard mask. • destination—Identifies the destination network. • destination-wildcard—Identifies the destination mask. You are expected to demonstrate your understanding of standard and extended access lists. You are not expected to memorize the available options in an extended access list. The options are provided in this chapter for your reference only. When constructing access lists, the built-in help feature (?) is extremely useful. Here are a few more complex examples of access lists. Example 4-39 permits Domain Naming System (DNS) packets, ICMP echo and echo replies, OSPF, and BGP packets. (BGP runs over TCP using port 179.) Example 4-39 Extended Access List Example access-list 100 permit tcp any any eq smtp ! Permits Simple Mail Transfer Protocols access-list 100 permit udp any any eq domain ! Permits DNS queries access-list 100 permit icmp any any echo ! Permits ICMP ping requests access-list 100 permit icmp any any echo-reply ! Permits ICMP replies access 100 permit ospf any any ! Permits OSPF packets access 100 permit tcp any any eq bgp ! Permits BGP to any device In Example 4-39, the access list numbered 100 is not concerned with specific host addresses or networks, but rather ranges of networks. The any keyword is shorthand for 0.0.0.0 255.255.255.255, which means that the device’s address is irrelevant. This address can be entered in shorthand as any. If any IP packet arrives to the router and does not match the specified criteria, the packet is dropped. The Cisco CD documentation provides additional quality examples of access lists. You should take some time to study Cisco’s examples available on the CD and at www.cisco.com under the technical documents link. Access lists are difficult to manage because you cannot explicitly delete a specific line; you must first remove the entire access list and re-enter the new access list with the correct order for numbered access lists. For a large access list that might contain over 1000 lines of code, any variations are completed on a TFTP server and copied to the startup configuration. I have
- 213. 190 Chapter 4: Cisco IOS Specifics and Security worked with some access lists that were 2500 lines in length and took over 5 minutes to load on Cisco routers. On the other hand, named access-lists lists allow you to determine where in the access list the new line will be placed. For more detail on named access-list, please visit, www.cisco.com/en/US/customer/products/sw/iosswrel/ps1831/products_configuration_guide _chapter09186a00800d9817.html. It might be a likely scenario for the CCIE security lab exam so please ensure you are fully comfortable with named and numbered access lists for the laboratory exam.
- 214. Foundation Summary 191 Foundation Summary The “Foundation Summary” is a condensed collection of material for a convenient review of key concepts in this chapter. If you are already comfortable with the topics in this chapter and decided to skip most of the “Foundation Topics” material, the “Foundation Summary” will help you recall a few details. If you just read the “Foundation Topics” section, this review should help further solidify some key facts. If you are doing your final preparation before the exam, the “Foundation Summary” offers a convenient and quick final review. Table 4-9 Cisco Device Commands and Information Command Description show flash Displays the content of the System Flash Standard IP access list range 1-99, 1300-1999 Extended access list range 100-199, 2000-2699 copy running-config startup-config IOS command to save running configuration from RAM to NVRAM copy startup-config running-config IOS command to save running configuration from NVRAM to RAM 0x2102 0x2102 is the standard default configuration register, which is IOS syntax: a 16-bit number defining how the router loads config-register value To ignore the startup configuration, use 0x2142 show version Displays detailed information about IOS and hardware configuration on a Cisco router Table 4-10 Advanced Cisco Device Operation IOS Command Description show debugging Displays the current debug commands processed by the CPU debug ? Displays a list of available debug options undebug all Turns off all possible debugging commands debug ip packet access-list Allows debugging of specific network address without burdening the router with every IP packet processed by the CPU
- 215. 192 Chapter 4: Cisco IOS Specifics and Security Table 4-11 Password Recovery Steps Step Description 1 Power cycle the router. 2 Issue a control break or the break key command on the application to enter into boot ROM mode. The control break key sequence must be entered within 60 seconds of the router restarting after a power cycle. 3 Once you are in ROM mode, change the configuration register value to ignore the startup configuration file that is stored in NVRAM. Use the o/r 0x2142 command. 4 Allow the router to reboot by entering the i command. 5 After the router has finished booting up without its startup configuration, look at the show startup-config command output. If the password is encrypted, move to Step 6, which requires you to enter the enable mode (type enable and you will not be required to enter any password) and copy the startup configuration to the running configuration with the copy startup-config running-config command. Then, change the password. If the password is not encrypted and the secret password is not used, you can simply read the password. Skip Steps 6 and 7 and go to Step 8. 6 Copy the startup configuration to RAM. 7 Enable all active interfaces. 8 Change the configuration register to 0x2102 (default). 9 Reload router. 10 Check the new password. Table 4-12 Basic Password Security IOS Command Description enable password password Defines the enable password (case-sensitive) to allow EXEC user to Privilege mode where configuration changes can be made. Typically not encrypted, and it is viewable when the configuration is displayed. enable secret password Sets the secret password to enable EXEC user to Privilege mode where configuration changes can be made. Overrides an enable password and is encrypted by default. service password-encryption Encrypts all passwords on Cisco routers.
- 216. Q&A 193 Q&A The Q & A questions are designed to help you assess your readiness for the topics covered on the CCIE Security written exam and those topics presented in this chapter. This format helps you assess your retention of the material. A strong understanding of the answers to these ques- tions will help you on the CCIE Security written exam. You can also look over the questions at the beginning of the chapter again for additional review. Use the CD-ROM provided with this book to take simulated exams, which draw from a database of over 300 multiple-choice ques- tions—all different from those presented in the book. Select the best answer. Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.” 1 Where is the running configuration stored on a Cisco router? 2 What IOS command displays the startup configuration? 3 What IOS command provides the following output? System flash directory: File Length Name/status 1 9558976 c2500-ajs40-l.12-17.bin [9559040 bytes used, 7218176 available, 16777216 total] 16384K bytes of processor board System flash 4 What configuration register will enable a Cisco router to ignore the startup configuration?
- 217. 194 Chapter 4: Cisco IOS Specifics and Security 5 To copy the startup configuration to the running configuration, what IOS command or commands are used? 6 What is the range for standard and extended IP access lists on Cisco IOS routers? 7 What command display the IP access lists configured on a Cisco router? 8 How do you disable all debug commands currently enabled on a Cisco router, assuming you are not sure what debug commands are enabled? 9 What must you be very careful of when enabling any form of debugging on a Cisco router? 10 What are the required steps when performing password recovery on a Cisco router? 11 What is the enable password for the following configuration? enable password CiscO
- 218. Scenario 4-1: Configuring Cisco Routers for Passwords and Access Lists 195 Scenario Scenario 4-1: Configuring Cisco Routers for Passwords and Access Lists Figure 4-6 displays a simple one-router network with two Ethernet LAN interfaces connecting users on subnet 131.108.1.0/24 to the server IP network, 131.108.2.0/24. Figure 4-6 Scenario Physical Topology 131.108.1.100/24 R1 131.108.1.1/24 131.108.2.1/24 Ethernet0/0 Ethernet0/1 131.108.2.100/24 131.108.1.101/24 Example 4-40 displays the working configuration file on R1 numbered from line 1 to 25. Example 4-40 R1’s Full Configuration 1. version 12.2 2. no service password-encryption 3. hostname R1 4. no logging console debugging 5. enable secret 5 $1$TBUV$od27CrEfa4UVICBtwvqol/ 6. enable password ciscO 7.interface Ethernet0/0 8. ip address 131.108.1.1 255.255.255.0 9.interface Ethernet0/1 10. ip address 131.108.2.1 255.255.255.0 11.no ip http server 12.access-list 1 permit 131.108.0.0 0.0.255.255 13.access-list 100 permit tcp any host 131.108.1.1 eq telnet 14.access-list 100 permit ip host 131.108.2.100 host 131.108.1.1 15.alias EXEC test show ip route ospf 16.alias EXEC eth0 show interface ethernet0/0 17.alias EXEC eth1 show interface ethernet0/1 continues
- 219. 196 Chapter 4: Cisco IOS Specifics and Security Example 4-40 R1’s Full Configuration (Continued) 18.line con 0 19.EXEC-timeout 0 0 20.login 21.line aux 0 22.line vty 0 4 23.EXEC-timeout 0 0 24.no login 25.end 1 The network administrator enables the debug ip packet command on Router R1, but no output is seen when connected to the console. IP traffic is following correctly from Ethernet0/0 to Ethernet0/1. What is the likely problem? What IOS configuration change is required to rectify the fault? 2 There are a number of configured aliases. What alias will display the Ethernet interface statistics for the Ethernet interface labeled Ethernet0/1? 3 When the following command is entered at the privilege EXEC prompt, what will the output be? R1#eth0 4 What is the password of Router 1 that enables a network administrator to make configuration changes? 5 What debug command can be used to debug IP packets’ source from the address 131.108.2.100 to the PC with the IP address of 131.108.1.100. 6 A user telnets to Router R1 and runs the debug command, debug ip packet. IP data travels from the PC to the server but no output is displayed on the router. What is the likely problem? R2#R1 Trying 131.108.255.1 ... Open R1>debug ip packet ^ % Invalid input detected at '^' marker. R1> 7 What is the configuration register of the router in Figure 4-6? 8 What is the VTY password required for Telnet clients logging into R1? 9 What does access list 1 accomplish in line 12? 10 What Global IOS command would encrypt all passwords configured on R1 in Figure 4-6?
- 220. Scenario Answers 197 Scenario Answers 1 Line 4 in Example 4-39 has disabled the debug output from being visible. To enable debug messages to be sent to the console port, the command logging console debugging must be configured in global configuration mode. Alternatively, telneting to the router and enabling the terminal monitor command via the VTY line enables the network administrator to view the debug output. 2 Line 17 displays the alias, eth1, which is the command show interface ethernet0/1. 3 Line 16 defines an alias, eth0, which will be used as a shortcut to the show interface ethernet0/0 command. This IOS command displays the statistics of interface Ethernet0/0. 4 Line 6 (enable password ciscO) defines the enable password as ciscO. However, because a secret password exists on line 5, that is the password required to enter enable mode, and because the secret password is encrypted, you cannot decipher the password. 5 Access list 100 defines an Access-list with the source address 131.108.2.100 to the destination IP address 131.108.1.100. You can apply the debug command, debug ip packet 100, with the optional keyword detail to view IP packets sent from the server to the IP address 131.108.1.100. 6 The Telnet user must be in privilege EXEC mode and must enable the terminal monitor command to ensure debug output is sent to the VTY line. 7 The configuration in Example 4-38 does not include a configuration register, so the default register (0x2102) is enabled. 8 Line 24 configures the router for no VTY login, so there is no password; any Telnet users will be directed to the router at the EXEC prompt level. 9 Access list 1 is not defined on any interface and can be used when debug ip packet is turned on. Because it is a standard access list, it can be used to debug packets’ source from network 131.108.0.0 to 131.108.255.255. 10 The Global IOS command, service password-encryption, encrypts all passwords, including the enable and VTY password, if any.
- 221. Exam Topics in This Chapter 1 Remote Authentication Dial-In User Service (RADIUS) 2 Terminal Access Controller Access Control System Plus (TACACS+) 3 Kerberos 4 Virtual Private Dial-up Networks (VPDN/Virtual Profiles) 5 Data Encryption Standard (DES) 6 Triple DES (DES3) 7 IP Secure (IPSec) 8 Internet Key Exchange (IKE) 9 Certificate Enrollment Protocol (CEP) 10 Point-to-Point Tunneling Protocol (PPTP) 11 Layer 2 Tunneling Protocol (L2TP)
- 222. CHAPTER 5 Security Protocols This chapter covers some of today’s most widely used technologies that give network administrators the ability to ensure sensitive data is secure from unauthorized sources. Standards such as IP security (IPSec) and encryption standards are covered, as are all the fundamental foundation topics you need to master the topics covered in the security written exam. This chapter covers the following topics: • Security protocols—This section covers the security protocols authentication, authorization, and accounting (AAA), RADIUS, Terminal Access Controller Access Control System Authentication Plus (TACACS+) protocol, and Kerberos. • Virtual private dial-up networks—This section covers VPDNs and their use in dialup IP networks. • Date encryption—This section covers encrypting IP using standard encryption, such as Triple Data Encryption Standard (DES) and IPSec. The mechanism used to authenticate encryption tunnels is also covered. • Certificate Enrollment Protocol—This section briefly covers the Cisco-defined certificate management protocol, CEP, and how a device communicates with a certificate authority. “Do I Know This Already?” Quiz This assessment quiz’s purpose is to help you determine how to spend your limited study time. If you can answer most or all these questions, you might want to skim the “Foundation Topics” section and return to it later, as necessary. Review the “Foundation Summary” section and answer the questions at the end of the chapter to ensure that you have a strong grasp of the material covered. If you already intend to read the entire chapter, you do not necessarily need to answer these questions now. If you find these assessment questions difficult, read through the entire “Foundation Topics” section and review it until you feel comfortable with your ability to answer all these and the Q & A questions at the end of the chapter.
- 223. 200 Chapter 5: Security Protocols Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.” 1 What are the three components of AAA? (Choose the three best answers.) a. Accounting b. Authorization c. Adapting d. Authentication 2 What IOS command must be issued to start AAA on a Cisco router? a. aaa old-model b. aaa model c. aaa new model d. aaa new-model e. aaa new_model 3 What algorithm initiates and encrypts a session between two routers’ exchange keys between two encryption devices? a. Routing algorithm b. Diffie-Hellman algorithm c. The switching engine d. The stac compression algorithm 4 Can you configure RADIUS and TACACS+ concurrently on a Cisco IOS router? a. No. b. Yes, provided you have the same lists names applied to the same interfaces. c. Yes, provided you have the different lists names applied to the same interfaces. d. Yes, provided you have the different lists names applied to different interfaces. 5 How do you enable a RADIUS server to debug messages for Cisco Secure on a UNIX server? a. Terminal monitor. b. Edit the configuration file on the router. c. Edit the syslog.conf and csu.cfg files. d. Not possible, as UNIX does not run IOS.
- 224. “Do I Know This Already?” Quiz 201 6 What RADIUS attribute is used by vendors and not predefined by RFC 2138? a. 1 b. 2 c. 3 d. 4 e. 13 f. 26 g. 333 h. 33 7 RADIUS can support which of the following protocols? a. PPP b. OSPF c. AppleTalk d. IPX e. NLSP 8 When a RADIUS server identifies the wrong password entered by the remote users, what packet type is sent? a. Accept-user b. Reject-users c. Reject-deny d. Reject-accept e. Reject-Error f. Access-reject 9 Identify the false statement about RADIUS. a. RADIUS is a defined standard in RFC 2138/2139. b. RADIUS runs over TCP port 1812. c. RADIUS runs over UDP port 1812. d. RADIUS accounting information runs over port 1646.
- 225. 202 Chapter 5: Security Protocols 10 What is the RADIUS key for the following configuration? If this configuration is not valid, why isn’t it? aaa authentication login use-radius group radius local aaa authentication ppp user-radius if-needed group radius aaa authorization exec default group radius aaa authorization network default group radius radius-server 3.3.3.3 radius-server key IlovemyMum a. IlovemyMum b. Ilovemymum c. This configuration will not work because the command aaa new-model is missing. d. 3.3.3.3 11 What is the RADIUS key for the following configuration? Aaa new-model aaa authentication login use-radius group radius local aaa authentication ppp user-radius if-needed group radius aaa authorization exec default group radius aaa authorization network default group radius radius-server 3.3.3.3 radius-server key IlovemyMum a. IlovemyMum b. Ilovemymum c. This configuration will not work. d. 3.3.3.3 12 What versions of TACACS does Cisco IOS support? (Select the best three answers.) a. TACACS+ b. TACACS c. Extended TACACS d. Extended TACACS+ 13 TACACS+ is transported over which TCP port number? a. 520 b. 23 c. 21 d. 20 e. 49
- 226. “Do I Know This Already?” Quiz 203 14 What is the predefined TACACS+ server key for the following configuration? radius-server host 3.3.3.3 radius-server key CCIEsrock a. 3.3.3.3 b. Not enough data c. CCIESROCK d. CCIEsRock e. CCIEsrock 15 What does the following command accomplish? tacacs_server host 3.3.3.3 a. Defines the remote TACACS+ server as 3.3.3.3 b. Defines the remote RADIUS server as 3.3.3.3 c. Not a valid IOS command d. 3.3.3.3 e. Host unknown; no DNS details for 3.3.3.3 provided 16 Which of the following protocols does TACACS+ support? a. PPP b. AppleTalk c. NetBIOS d. All the above 17 Kerberos is defined at what layer of the OSI model? a. Layer 1 b. Layer 2 c. Layer 3 d. Layer 4 e. Layer 5 f. Layer 6 g. Layer 7
- 227. 204 Chapter 5: Security Protocols 18 What definition best describes a key distribution center when Kerberos is applied to a network? a. A general term that refers to authentication tickets b. An authorization level label for Kerberos principals c. Applications and services that have been modified to support the Kerberos credential infrastructure d. A domain consisting of users, hosts, and network services that are registered to a Kerberos server e. A Kerberos server and database program running on a network host 19 What definition best describes a Kerberos credential? a. A general term that refers to authentication tickets b. An authorization level label for Kerberos principals c. Applications and services that have been modified to support the Kerberos credential infrastructure d. A domain consisting of users, hosts, and network services that are registered to a Kerberos server e. A Kerberos server and database program running on a network host 20 What definition best describes Kerberized? a. A general term that refers to authentication tickets b. An authorization level label for Kerberos principals c. Applications and services that have been modified to support the Kerberos credential infrastructure d. A domain consisting of users, hosts, and network services that are registered to a Kerberos server e. A Kerberos server and database program running on a network host 21 What definition best describes a Kerberos realm? a. A general term that refers to authentication tickets b. An authorization level label for the Kerberos principals c. Applications and services that have been modified to support the Kerberos credential infrastructure d. A domain consisting of users, hosts, and network services that are registered to a Kerberos server e. A Kerberos server and database program running on a network host
- 228. “Do I Know This Already?” Quiz 205 22 What IOS command enables VPDN in the global configuration mode? a. vpdn-enable b. vpdn enable c. vpdn enable in interface mode d. Both a and c are correct 23 What is the number of bits used with a standard DES encryption key? a. 56 bits b. 32 bits; same as IP address c. 128 bits d. 256 bits e. 65,535 bits f. 168 bits 24 What is the number of bits used with a 3DES encryption key? a. 56 bits b. 32 bits; same as IP address c. 128 bits d. 256 bits e. 65,535 bits f. 168 bits 25 In IPSec, what encapsulation protocol encrypts only the data and not the IP header? a. ESP b. AH c. MD5 d. HASH e. Both a and b are correct. 26 In IPSec, what encapsulation protocol encrypts the entire IP packet? a. ESH b. AH c. MD5 d. HASH e. Both a and b are correct.
- 229. 206 Chapter 5: Security Protocols 27 Which of the following is AH’s destination IP port? a. 23 b. 21 c. 50 d. 51 e. 500 f. 444 28 Which of the following is ESP’s destination IP port? a. 23 b. 21 c. 50 d. 51 e. 500 f. 444 29 Which of the following is not part of IKE phase I negotiations? a. Authenticating IPSec peers b. Exchanges keys c. Establishes IKE security d. Negotiates SA parameters 30 Which of the following is not part of IKE phase II? a. Negotiates IPSec SA parameters b. Periodically updates IPSec SAs c. Rarely updates SAs (at most, once a day) d. Established IPSec security parameters 31 Which is the faster mode in IPSEC? a. Main mode b. Fast mode c. Aggressive mode d. Quick mode
- 230. “Do I Know This Already?” Quiz 207 32 Certificate Enrollment Process (CEP) runs over what TCP port number? (Choose the best two answers.) a. Same as HTTP b. Port 80 c. Port 50 d. Port 51 e. Port 333 f. Port 444
- 231. 208 Chapter 5: Security Protocols Foundation Topics Authentication, Authorization, and Accounting (AAA) Authentication, authorization, and accounting, (pronounced triple A) provides security to Cisco IOS routers and network devices beyond the simple user authentication available on IOS devices. AAA provides a method to identify which users are logged into a router and each user’s authority level. AAA also provides the capability to monitor user activity and provide accounting information. In today’s IP networks, access to network data is available in a variety of methods, including the following: • PSTN Dialup modems • ISDN dialup • Access through the Internet through virtual private networks (VPNs) The AAA model is defined as follows: • Authentication—Who are you? • Authorization—What resources are you permitted to use? • Accounting—What resources were accessed, what time, by whom were they used, and what commands were issued? The three phases ensure that legitimate users are permitted access. A remote user must be authenticated before being permitted access to network resources. Authentication allows the user to submit a username and password and permit challenges and responses. After the user is authenticated, authorization defines what services or resources in the network are permitted access. The operations permitted here can include IOS privileged exec commands. For example, a user might type commands but be permitted to type only certain show and debug commands, which are being authorized. Accounting allows the network administrator to log and view what was actually performed (for example, if a Cisco router was reloaded or the configuration was changed). Accounting ensures that an audit will allow network administrators the ability to view what was performed and at what time it was performed. Accounting keeps track of auditing and reporting network resource usage information. This typically includes the username, the start and stop time of login, and the commands typed by the user.
- 232. Authentication, Authorization, and Accounting (AAA) 209 NOTE To start AAA on a Cisco router, issue the following IOS command: aaa new-model On a PIX Firewall, the command syntax is as follows: aaa-server Figure 5-1 displays a typical secure network scenario. Figure 5-1 Secure Network Access The users could be dialup users running Async (in this case PSTN) or using ISDN with Point- to-Point Protocol (PPP). The Network Access Server (NAS) ensures that only authenticated users have access to the secure network; it maintains resources and accounting information. Authorization tells which resources, or host devices, are authorized to be accessed (such as FTP servers). The NAS implements the AAA protocols and also collects data regarding what network resources were accessed. The NAS can also ensure that devices in the secured network require authentication. For example, the users in Figure 5-1 who are accessing Router R1 will require a valid username/password pairing to enter any IOS commands.
- 233. 210 Chapter 5: Security Protocols The following sections further define what authentication, authorization, and accounting are by discussing a common Cisco IOS router example. Authentication Authentication allows administrators to identify who can connect to a router by including the user’s username and password. Normally, when a user connects to a router remotely by Telnet, the user must supply only a password and the administrator has no way of knowing the user’s username. You can, however, configure local usernames and passwords on a Cisco IOS router, but this does not scale well and it is not very secure. Configuring a small set of routers with indi- vidual usernames and passwords (IOS syntax username username password password) is fine, but doing so for large networks would be a difficult exercise to manage. Centrally locating the usernames and passwords is a better solution because only a few devices need to be updated and maintained. Also, users are not logged, and their configuration changes are not monitored without further configuration changes made on each individual router. Example 5-1 displays a sample code snippet of a remote user accessing an AAA-configured Cisco router by Telnet. Example 5-1 Username/Password Pair Entry Sydney>telnet San-Fran Trying san-fran (10.99.1.1)... Open User Access Verification Username: benjamin Username Password: xxxxxxxx Password San-Fran> As you can see in Example 5-1, the user must enter a valid username and password to gain access to the router. Typically, a database containing the valid usernames resides locally on the router or on a remote security server. Authorization Authorization comes into play after authentication. Authorization allows administrators to control the level of access users have after they successfully gain access to the router. Cisco IOS allows certain access levels (called privilege levels) that control which IOS commands the user can issue. For example, a user with a privilege level of 0 cannot issue any IOS commands. A user with a privilege level of 15 can perform all valid IOS commands. The local database or remote security server can grant the required privilege levels. Remote security servers, such as RADIUS and TACACS+, authorize users for specific rights by associating attribute-value (AV) pairs, which define those rights with the appropriate user. AAA authorization assembles a set of attributes that describes what the user is authorized to perform.
- 234. Authentication, Authorization, and Accounting (AAA) 211 These attributes are compared with the information contained in a database for a given user, and the result is returned to AAA to determine the user’s actual permissions and restrictions. You can display the user’s privilege level on a Cisco router with the show privilege command. Example 5-2 displays the privilege level when the enable password has already been entered. Example 5-2 show privilege Command R1#show privilege Current privilege level is 15 The higher the privilege, the more capabilities a user has with the IOS command set. Accounting Accounting occurs after authentication and authorization have been completed. Accounting allows administrators to collect information about users. Specifically, administrators can track which user logged into which router, which IOS commands a user issued, and how many bytes were transferred during a user’s session. For example, accounting enables administrators to monitor which routers have had their configurations changed. Accounting information can be collected by a router or by a remote security server. To display local account information on a Cisco router collecting accounting information, issue the show accounting IOS command. Example 5-3 displays sample output when the command is issued on Router R1. Example 5-3 show accounting Command R1#show accounting Active Accounted actions on Interface Serial0:1, User jdoe Priv 1 Task ID 15 Network Accounting record, 00:00:18 Elapsed 15, record task_id=15 timezone=PDT service=ppp mlp-links-max=4 mlp-links-current=4 protocol=ip addr=119.0.0.2 mlp-sess-id=1 Overall Accounting Traffic Starts Stops Updates Active Drops Exec 0 0 0 0 0 Network 8 4 0 4 0 Connect 0 0 0 0 0 Command 0 0 0 0 0 Rsrc-mgmt 1 0 0 1 0 System 0 0 0 0 0 User creates:21, frees:9, Acctinfo mallocs:15, frees:6 Users freed with accounting unaccounted for:0 Queue length:0 Table 5-1 describes the fields contained in Example 5-3.
- 235. 212 Chapter 5: Security Protocols Table 5-1 show accounting Fields Field Description User The user’s ID Priv The user’s privilege level (0-15) Task ID Each accounting session’s unique identifier Accounting Record Type of accounting session Elapsed Length of time (hh:mm:ss) for this session type Rather than maintain a separate database with usernames, passwords, and privilege levels, you can use external security servers to run external security protocols—namely RADIUS, TACACS+, and Kerberos. These security server protocols stop unauthorized access to your network. The following sections review these three security protocols. Security Server Protocols In many circumstances, AAA uses security protocols to administer its security functions. If your router or access server is acting as a NAS, AAA is the means through which you establish communication between your network access server and your RADIUS, TACACS+, or Kerberos security server. Remote Authentication Dial-In User Service (RADIUS) RADIUS is a client/server-based system that secures a Cisco network against intruders. Imple- mented in IOS, RADIUS sends authentication requests to a RADIUS server. Radius was created by Livingston Enterprises and is now defined in RFC 2138/2139. A RADIUS server is a device that has the RADIUS daemon or application installed. RADIUS must be used with AAA to enable the authentication, authorization, and accounting of remote users when using Cisco IOS routers. When a RADUIS server authenticates a user, the following events occur: 1 The user is prompted for and enters a username and password. 2 The username and encrypted password are sent over the network to the RADIUS server.
- 236. Remote Authentication Dial-In User Service (RADIUS) 213 3 The user receives one of the following responses from the RADIUS server: ACCEPT—The user is authenticated. ACCEPT-REJECT—The user is not authenticated and is prompted to re-enter the username and password, or access is denied. The RADIUS server sends this response when the user enters an invalid username/password pairing. CHALLENGE—A challenge is issued by the RADIUS server. The challenge collects additional data from the user. CHANGE PASSWORD—The RADIUS server issues a request asking the user to select a new password. An ACCEPT or REJECT response can contain additional information for services that the user can access, including Telnet, rlogin, or local-area transport (LAT) connections, and PPP, Serial Line Internet Protocol (SLIP), or EXEC services. RADIUS is commonly used when PPP is used. Figure 5-2 displays a typical PPP connection request to a RADIUS server. Figure 5-2 RADIUS Sequence Example Network Access Server — • User initiates connection with a packet type labeled Radius Server ACCESS-REQUEST-username/password prompt is sent by Radius Server. • User enters username/password (username in cleartext password is encrypted). • RADIUS server accepts or rejects request with packet PPP type ACCESS-ACCEPT/REJECT. Request UDP port 1812 • Optional Challenge response. is used. Username: Simon User is prompted with Username/Password. Password: Uy_%#! The RADIUS server accepts or rejects a username and password pair. In some instances, a user might be asked to enter more information (this is called a challenge response). For example, if a user’s password has expired, a RADUIS server will prompt the user for a new password.
- 237. 214 Chapter 5: Security Protocols Transactions between the client (end user) and the RADIUS server are authenticated through a shared secret. The username is sent as clear text. RADIUS supports both Password Authentica- tion Protocol (PAP) and Challenge Handshake Authentication Protocol (CHAP). PAP and CHAP are security protocols that allow users to gain access to remote devices with PPP. A RADIUS server will never send the user’s password over the network in any circumstance. If the username/password pairing is entered incorrectly, the RADIUS server will send an ACCESS_REJECT response. The end user must re-enter the pairings or the connection will be rejected. RADIUS supports a number of predefined attributes that can be exchanged between client and server, such as the client’s IP address. RADIUS attributes carry specific details about authentication. RFC 2138 defines a number of attributes. The following bulleted list provides details from the most common attributes: • Attribute type 1—Username (defines usernames, such as numeric, simple ASCII characters, or a Simple Mail Transfer Protocol [SMTP] address) • Attribute type 2—User Password (defines the password, which is encrypted using Message Digest 5 [MD5]) • Attribute type 3—CHAP Password (used only in access-request packets) • Attribute type 4—NAS IP address (defines the NAS’s IP address; used only in access- request packets) • Attribute type 5—NAS Port (this is not the User Datagram Protocol (UDP) port number; it indicates the NAS’s physical port number, ranging from 0 to 65,535) • Attribute type 6—Service-Type (Type of service requested or type of service to be provided). Not supported by Cisco IOS. • Attribute type 7—Protocol (defines required framing; for example, PPP is defined when this attribute is set to 1 and Serial Line Internet Protocol [SLIP] is set to 2) • Attribute type 8—IP address (defines the IP address to be used by the remote user) • Attribute type 9—IP subnet mask (defines the subnet mask to be used by the remote user) • Attribute type 10—Routing • Attribute type 13—Compression • Attribute type 19—Callback ID • Attribute type 26—Vendor-specific. Cisco (vendor-ID 9) uses one defined option: vendor type 1 named cisco-avpair; this attribute transmits TACACS+ A/V pairs • Attribute type 61—NAS port type Table 5-2 summarizes RADIUS protocol’s main features
- 238. Remote Authentication Dial-In User Service (RADIUS) 215 Table 5-2 Summary of Radius Protocol Features Attribute Features UDP Packets sent between client and server are UDP primarily because TCP’s overhead does not allow for significant advantages. Typically, the user can wait for a username/password prompt. UDP destination 1812, port 1646 used for accounting. RADIUS is an industry standard defined in PORT RFC 2138. Attributes Attributes are used to exchange information between the NAS and client. Model Client/server-based model where packets are exchanged in a unidirectional manner. Encryption Password is encrypted using MD5; the username is not. RADIUS encrypts only the method password in the access-request packet, from the client to the server. The remainder of the packet is transmitted in clear text. A third party can capture other information, such as username, authorized services, and accounting. Multiprotocol Does not support protocols such as AppleTalk, NetBIOS, or IPX. IP is the only support protocol supported. Now, examine the RADIUS configuration tasks required on a Cisco router. RADIUS Configuration Task List A RADIUS server is usually software that runs on a variety of platforms, including Microsoft NT servers or a UNIX host. RADIUS can authenticate router users and vendors, and even validate IP routes. To configure RADIUS on your Cisco router or access server, perform the following tasks: Step 1 Enable AAA with the aaa new-model global configuration command. AAA must be configured if you plan to use RADIUS. Step 2 Use the aaa authentication global configuration command to define method lists for RADIUS authentication. Step 3 Use line and interface commands to enable the defined method lists to be used. Step 4 Define the RADIUS server and secret key with the following IOS commands: radius-server ip address radius-server key secret key NOTE There are two optional RADIUS commands: Use the aaa authorization global command to authorize specific user functions. Use the aaa accounting command to enable accounting for RADIUS connections.
- 239. 216 Chapter 5: Security Protocols Examples are the best method to show the enormous IOS command set that is available for use when configuring RADIUS support with AAA. Example 5-4 configures a Cisco IOS router with AAA and RADIUS support. Example 5-4 AAA and RADIUS aaa new-model aaa authentication login use-radius group radius local aaa authentication ppp user-radius if-needed group radius aaa authorization exec default group radius aaa authorization network default group radius radius-server 3.3.3.3 radius-server key IlovetheMotheroftheEucharist The command lines in this RADIUS authentication and authorization configuration are defined as follows: • The aaa authentication login use-radius group radius local command configures the router to use RADIUS for authentication at the login prompt. If RADIUS returns an error, the user is authenticated using the local database. In this example, use-radius is the name of the method list, which specifies RADIUS and then local authentication. If the RADIUS server returns the REJECT response, the user is denied access and the router will not check its local database. • The aaa authentication ppp user-radius if-needed group radius command configures the Cisco IOS Software to use RADIUS authentication for lines using PPP with CHAP or PAP, if the user is not already authorized. If the EXEC facility has authenticated the user, RADIUS authentication is not performed. In this example, user-radius is the name of the method list defining RADIUS as the if-needed authentication method. • The aaa authorization exec default group radius command sets the RADIUS information used for EXEC authorization, autocommands, and access lists. • The aaa authorization network default group radius command sets RADIUS for network authorization, address assignment, and access lists. • The radius-server commands define the NAS. • The radius-server key commands define the shared secret text string between the network access server and the RADIUS server host. Example 5-5 displays an example in which AAA is enabled on a Cisco IOS router. Example 5-5 AAA and RADIUS Example Hostname R1 username simon password SimonisisAgreatdrummeR aaa new-model aaa authentication ppp dialins group radius local
- 240. Remote Authentication Dial-In User Service (RADIUS) 217 Example 5-5 AAA and RADIUS Example (Continued) aaa authorization network default group radius local aaa accounting network default start-stop group radius aaa authentication login simon local aaa authorization exec default local radius-server host 3.3.3.3 radius-server key CCIEsrock The Example 5-5 line configurations are defined as follows: • The radius-server host command defines the RADIUS server host’s IP address. • The radius-server key command defines the shared secret text string between the network access server and the RADIUS server host. • The aaa authentication ppp dialins group radius local command defines the authen- tication method list, dialins, which specifies that RADIUS authentication and then (if the RADIUS server does not respond) local authentication will be used on serial lines using PPP. • The aaa authorization network default group radius local command assigns an address and other network parameters to the RADIUS user. • The aaa accounting network default start-stop group radius command tracks PPP usage. This command is used for all network services. Can be PPP, but also SLIP or ARAP. • The aaa authentication login simon local command defines method list, simon, for local authentication. • The aaa authentication login simon command applies the simon method list for login authentication. NOTE A method list simply defines the authentication methods to be used, in sequence, to authenticate a user. Method lists enable you to designate one or more security protocols to be used for authentication, ensuring a backup system for authentication in case the initial method fails. Cisco IOS Software uses the first method listed to authenticate users; if that method does not respond, the Cisco IOS Software selects the next authentication method listed. This process continues until there is successful communication with a listed authentication method or the authentication method list is exhausted, in which case authentication fails. TIP Cisco’s website provides a long list of configuration examples. To view more detailed configurations, visit the following web address and follow the link to Security: www.cisco.com/kobayashi/technotes/serv_tips.shtml
- 241. 218 Chapter 5: Security Protocols Terminal Access Controller Access Control System Plus (TACACS+) Cisco IOS supports three versions of TACACS—TACACS, extended TACACS, and TACACS+. All three methods authenticate users and deny access to users who do not have a valid username/password pairing. Cisco has also developed Cisco Secure Access Control Server (CSACS), a flexible family of security servers that supports both RADIUS and TACACS+. You can even run debugging com- mands on the Cisco Secure ACS software. In UNIX, you can modify files, such as syslog.conf and csu.cfg, to change the output to your screen. For more details on how to debug on a UNIX server, see www.cisco.com/warp/public/480/cssample2x.html#debug. TACACS+ has the following features: • TCP packets (port 49) ensure that data is sent reliably across the IP network. • Supports AAA architectures and, in fact, separates each of the three mechanisms (authentication, authorization, and accounting). • The data between the user and server is encrypted. • Supports both PAP/CHAP and multiprotocols, such as IPX and X.25. • Access lists can be defined on a user basis. Figure 5-3 displays a typical TACACS+ connection request (Authentication). Figure 5-3 TACACS+ Authentication Example Sequence TACACS+ Server RESPONSE RESPONSE Authorization START RECORD Network Access Authentication Process Server • User initiates PPP connection to the NAS. • NAS sends START packet to the TACACS+ server. User initiates PPP request • TACACS+ server responds with GETUSER packets PPP that contains the prompt username/password. • The NAS sends the displays to the remote USER. • USER responds with username/password pair. • The TACACS+ server checks username/password and sends back a pass or fail packet to the NAS. • Connection is then set up or rejected. Username: Simon User is prompted with • Followed by Authorization. Password: Uy_%#! Username/Password. • Followed by Accounting.
- 242. Terminal Access Controller Access Control System Plus (TACACS+) 219 When a TACACS+ server authenticates a remote user, the following events occur: 1 When the connection is established, the NAS contacts the TACACS+ daemon to obtain a username prompt, which is then displayed to the user. The user enters a username and the NAS and contacts the TACACS+ daemon to obtain a password prompt. The NAS displays the password prompt to the user, the user enters a password, and the password is sent to the TACACS+ daemon. 2 The NAS eventually receives one of the following responses from the TACACS+ daemon: • ACCEPT—The user is authenticated and service can begin. If the NAS is configured to require authorization, authorization will begin at this time. • REJECT—The user has failed to authenticate. The user can be denied further access or will be prompted to retry the login sequence, depending on the TACACS+ daemon. • ERROR—An error occurred at some time during authentication. This can be either at the daemon or in the network connection between the daemon and the NAS. If an ERROR response is received, the NAS typically tries to use an alternative method for authenticating the user. • CONTINUE—The user is prompted for additional authentication information. 3 A PAP login is similar to an ASCII login, except that the username and password arrive at the NAS in a PAP protocol packet instead of being typed in by the user, so the user is not prompted. PPP CHAP logins are also similar, in principle. 4 Following authentication, the user is required to undergo an additional authorization phase, if authorization has been enabled on the NAS. Users must first successfully complete TACACS+ authentication before proceeding to TACACS+ authorization. 5 If TACACS+ authorization is required, the TACACS+ daemon is again contacted and it returns an ACCEPT or REJECT authorization response. If an ACCEPT response is returned, the response will contain data in the form of attributes used to direct the EXEC or NETWORK session for that user, determining services that the user can access. Services include the following: • Telnet, rlogin, Point-to-Point Protocol (PPP), Serial Line Internet Protocol (SLIP), or EXEC services • Connection parameters, including the host or client IP address, access list, and user timeouts The TACACS+ authorization process is defined as the packet flow between the NAS and the TACACS+ server. The packets exchanged between the NAS and server contain attribute pairs (AV pairs). The NAS sends Start packets and the TACACS+ server responds with Response packets. The server can permit, deny, or modify commands requested by the end user. The data (that contains the full list of all username/password pairs) is stored on a local file defining what commands are permitted by the end user, for example.
- 243. 220 Chapter 5: Security Protocols TACACS+ accounting provides an audit record of what commands were completed. The NAS sends a record of any commands, and the TACACS+ server sends a response acknowledging the accounting record. Table 5-3 summarizes the main features of TACACS+. Table 5-3 Summary of TACACS+ Protocol Feature Feature TCP Packets sent between client and server are TCP. Typically, the user can wait for a username/password prompt. TCP destination port Port 49. Attributes Packet types are defined in TACACS+ frame format as follows: Authentication 0x01 Authorization 0x02 Accounting 0x03 Seq_no The sequence number of the current packet flow for the current session. The Seq_no starts with 1, and each subsequent packet will increment by one. The client sends only odd numbers. TACACS+ server sends only even numbers. Encryption method Entire packet is encrypted. Data is encrypted using MD5 and a secret key that matches both on the NAS (for example, a Cisco IOS router) and the TACACS+ server. Multiprotocol support Support protocols, such as AppleTalk, NetBIOS, or IPX, along with IP. Now, examine the TACACS+ configuration tasks required when enabling TACACS+ on a Cisco IOS router. TACACS+ Configuration Task List To configure your router to support TACACS+, you must perform the following tasks: Step 1 Use the aaa new-model global configuration command to enable AAA, which must be configured if you plan to use TACACS+. For more information about using the aaa new-model command, refer to the link, www.cisco.com/univercd/ cc/td/doc/product/software/ios121/121cgcr/secur_c/scprt1/index.htm. Step 2 Use the tacacs-server host command to specify the IP address of one or more TACACS+ daemons. The command is as follows: tacacs-server host hostname [single-connection] [port integer] [timeout integer] [key string]
- 244. Terminal Access Controller Access Control System Plus (TACACS+) 221 Step 3 Use the tacacs-server key command to specify an encryption key to encrypt all exchanges between the network access server and the TACACS+ daemon. This same key must also be configured on the TACACS+ daemon. The actual command is as follows: tacacs-server key key The key should match the one used on the TACACS+ daemon. Step 4 Use the aaa authentication global configuration command to define method lists that use TACACS+ for authentication. Step 5 Use line and interface commands to apply the defined method lists to various interfaces. Step 6 To enable authorization, use the aaa authorization global command to configure authorization for the NAS. Unlike authentication, which can be configured per line or per interface, authorization is configured globally for the entire NAS. Step 7 To enable accounting for TACACS+ connections, use the aaa accounting command. Optional commands include the following: — Configuring AAA server groups (Optional) — Configuring AAA server group selection based on DNIS (Optional) — Specifying TACACS+ authentication (Required) — Specifying TACACS+ authorization (Optional) — Specifying TACACS+ accounting (Optional) Example 5-6 displays a sample configuration of a Cisco router with TACACS+ authentication for PPP. Example 5-6 TACACS+ Authentication for PPP Example aaa new-model aaa authentication ppp CCIE group tacacs+ local tacacs-server host 10.1.2.3 tacacs-server key cciesarecool interface serial 0 ppp authentication chap pap CCIE The configuration lines in Example 5-6 are defined as follows: • The aaa new-model command enables the AAA security services. • The aaa authentication command defines a method list, CCIE, to be used on serial inter- faces running PPP. The keyword group tacacs+ means that authentication is done through TACACS+. If TACACS+ returns an ERROR during authentication, the keyword local indi- cates that authentication will be attempted using the local database on the NAS. Note that the local database is not used if a REJECT response is received from the security server.
- 245. 222 Chapter 5: Security Protocols • The tacacs-server host command identifies the TACACS+ daemon as having an IP address of 10.1.2.3. The tacacs-server key command defines the shared encryption key as cciesarecool. • The interface command selects the line, and the ppp authentication command applies the test method list to this line. Example 5-7 shows how to configure TACACS+ as the security protocol for PPP authentication using the default method list; it also shows how to configure network authorization through TACACS+. Example 5-7 Authorization and TACACS+ Example aaa new-model aaa authentication ppp default if-needed group tacacs+ local aaa authorization network default group tacacs+ tacacs-server host 3.3.3.3 tacacs-server key simoniscool interface serial 0 ppp authentication default The lines in the preceding sample configuration are defined as follows: • The aaa new-model command enables the AAA security services. • The aaa authentication command defines a method list, default, to be used on serial interfaces running PPP. The keyword default means that PPP authentication is applied by default to all interfaces. The if-needed keyword means that if the user has already authenticated by going through the ASCII login procedure, PPP authentication is not necessary and can be skipped. If authentication is needed, the keyword group tacacs+ means that authentication is done through TACACS+. If TACACS+ returns an ERROR during authentication, the keyword local indicates that authentication will be attempted using the local database on the NAS. • The aaa authorization command configures network authorization via TACACS+. • The tacacs-server host command identifies the TACACS+ daemon as having an IP address of 3.3.3.3. • The tacacs-server key command defines the shared encryption key as simoniscool. • The interface command selects the line, and the ppp authentication command applies the default method list to this line. Example 5-8 displays a sample configuration where accounting is also enabled.
- 246. Terminal Access Controller Access Control System Plus (TACACS+) 223 Example 5-8 Accounting Example aaa new-model aaa authentication ppp default if-needed group tacacs+ local aaa accounting network default stop-only group tacacs+ tacacs-server host 3.3.3.3 tacacs-server key andrewiscool interface serial 0 ppp authentication default The lines in the Example 5-8 configuration are defined as follows: • The aaa new-model command enables the AAA security services. • The aaa authentication command defines a method list, default, to be used on serial interfaces running PPP. The keyword default means that PPP authentication is applied by default to all interfaces. The if-needed keyword means that if the user has already authenticated through the ASCII login procedure, PPP authentication is not necessary. If authentication is needed, the keyword group tacacs+ means that authentication is done through TACACS+. If TACACS+ returns an ERROR during authentication, the keyword local indicates that authentication will be attempted using the local database on the NAS. • The aaa accounting command configures network accounting through TACACS+. In this example, accounting records stop-only, meaning that the session that just terminated will be sent to the TACACS+ daemon whenever a network connection terminates. • The interface command selects the line, and the ppp authentication command applies the default method list to this line. NOTE You can define a group of TACACS+ servers by defining the servers with the IOS command, tacacs-server <ip address of server>. For example, to define six servers you would use the IOS configuration: tacacs-server host 1.1.1.1 tacacs-server host 2.2.2.2 tacacs-server host 3.3.3.3 tacacs-server host 4.4.4.4 tacacs-server host 5.5.5.5 tacacs-server host 6.6.6.6 tacacs-server key ccie If the first server does not respond within a timeout period (default 5 seconds), the next server is queried, and so forth. Typically, the console port is not configured for authorization.
- 247. 224 Chapter 5: Security Protocols TACACS+ Versus RADIUS Table 5-4 compares the main differences between TACACS+ and RADIUS. Table 5-4 TACACS+/RADIUS Comparison RADIUS TACACS+ Packet delivery UDP TCP Packet encryption RADIUS encrypts only the password TACACS+ encrypts the entire body in the access-request packet from the of the packet but leaves a standard client to the server. TACACS+ header. AAA support RADIUS combines authentication TACACS+ uses the AAA architec- and authorization. ture, separating authentication, authorization, and accounting. Multiprotocol support None. TACACS+ supports other protocols, such as AppleTalk, NetBIOS, and IPX. Router management RADIUS does not allow users to TACACS+ allows network control which commands can be administrators control over which executed on a router. commands can be executed on a router. NOTE You can configure both RADIUS and TACACS+ concurrently on a Cisco router provided that you have defined different list names and applied the list to different interfaces. NOTE You can download and install a trial copy of Cisco Secure ACS for Windows NT/2000 or UNIX. This comes with a built–in RADIUS and TACACS+ server. You also need a Cisco router with IOS 12.X with one working Ethernet port. This will reinforce your understanding of the AAA concept. For more information, visit the Cisco Secure Software center at www.cisco.com. The AAA configuration options are numerous, and those presented in this guide are only a small subset of a larger set you can view online at Cisco’s website. Visit the following URL for more quality examples of how AAA, along with RADIUS or TACACS, can be implemented on Cisco IOS routers: www.cisco.com/cgi-bin/Support/browse/index.pl?i=Technologies&f=1408 The IOS debug command set for RADIUS and TACACS is extensive. Presented here are some common RADIUS and TACACS debug outputs found in real networks.
- 248. Kerberos 225 Example 5-9 displays a sample output from the debug aaa authentication command for a RADIUS login attempt that failed. The information indicates that TACACS is the authentication method used. Example 5-9 debug aaa authentication R1# debug aaa authentication 14:02:55: AAA/AUTHEN (164826761): Method=RADIUS 14:02:55: AAA/AUTHEN (164826761): status = GETPASS 14:03:01: AAA/AUTHEN/CONT (164826761): continue_login 14:03:01: AAA/AUTHEN (164826761): status = GETPASS 14:03:04: AAA/AUTHEN (164826761): status = FAIL Example 5-10 displays a sample output from the debug radius command that shows a successful login attempt, as indicated by an Access-Accept message: Example 5-10 debug radius Failure R1# debug radius 13:59:02: Radius: IPC Send 0.0.0.0:1645, Access-Request, id 0xB, len 56 13:59:02: Attribute 4 6 AC150E5A 13:59:02: Attribute 5 6 0000000A 13:59:02: Attribute 1 6 62696C6C 13:59:02: Attribute 2 18 0531FEA3 13:59:04: Radius: Received from 131.108.1.1:1645, Access-Accept, id 0xB, len 26 Access-Accept 13:59:04: Attribute 6 6 00000001 Example 5-11 displays a sample output from the debug radius command that shows an unsuccessful login attempt, as indicated by an Access-Reject message. Example 5-11 debug radius Command R1# debug radius 13:57:56: Radius: IPC Send 0.0.0.0:1645, Access-Request, id 0xA, len 57 13:57:56: Attribute 4 6 AC150E5A 13:57:56: Attribute 5 6 0000000A 13:57:56: Attribute 1 7 62696C6C 13:57:56: Attribute 2 18 49C28F6C 13:57:59: Radius: Received from 171.69.1.152:1645, Access-Reject, id 0xA, len 20 Access-Reject Kerberos Kerberos is a trusted third-party authentication application layer service (Layer 7 of the OSI model). Kerberos is a secret-key network authentication protocol developed at the Massachusetts Institute of Technology (MIT) that uses the Data Encryption Standard (DES) cryptographic
- 249. 226 Chapter 5: Security Protocols algorithm for encryption and authentication. In the Kerberos protocol, this trusted third party is called the key distribution center (KDC). Figure 5-4 displays the Kerberos authentication process when a remote client initiates a remote Telnet session. (Kerberos supports Telnet, rlogin, rsh, and rcp.) Figure 5-4 Authentication Service with Kerberos Key Distribution Center (KDC) 3. R1 4. Authentication Process 2. • User initiates Telnet session to Router R1. Network • The NAS builds a Service credential request Access and sends it to the KDC. Server • KDC decrypts the request and builds service credential, sends to user Simon. IP Network • User Simon decrypts. 6. 5. • R1 decrypts credential. • User Simon exchanges data with Router R1. 1. User: Simon Kerberos’s primary use is to verify that users and the network services they employ are really who and what they claim to be. To accomplish this, a trusted Kerberos server issues tickets to users. These tickets, which have a limited lifespan, are stored in a user’s credential cache and can be used in place of the standard username/password authentication mechanism. The Kerberos credential scheme embodies a concept called single logon. This process requires authenticating a user once, and then allows secure authentication (without encrypting another password) wherever that user’s credential is accepted. Timestamps (large numbers representing the current date and time) have been added to the original Kerberos model to aid in the detection of replay attacks. Replay attacks basically reply to data flow with an unauthorized source attempting to gain access to a host. During the packet flow exchange, critical parameters exchanged are the client’s name, the IP address, and the
- 250. Kerberos 227 current workstation time. System time must be accurate to ensure replay attacks are avoided or, at the very least, detected, and the Kerberos session terminated. NOTE Starting with Cisco IOS Release 11.2, Cisco IOS Software includes Kerberos 5 support, which allows organizations already deploying Kerberos 5 to use the same Kerberos authentication database on their routers that they already use on their other network hosts (such as UNIX servers and PCs). Table 5-5 summarizes the key concepts of Kerberos. Table 5-5 Features of the Kerberos Protocol Feature Description Packet delivery A number of ports are defined: TCP/UDP ports 88, 543, 749, and TCP ports 754, 2105, and 4444. Packet encryption Supports username/password encryption. Telnet support Telnet sessions can be encrypted. Table 5-6 defines common Kerberos terminology. Table 5-6 Kerberos Terminology Term Definition Credential A general term that refers to authentication tickets, such as ticket granting tickets (TGTs) and service credentials. Kerberos credentials verify the identity of a user or service. If a network service decides to trust the Kerberos server that issued a ticket, it can be used in place of retyping in a username and password. Credentials have a default lifespan of eight hours. Instance An authorization level label for Kerberos principals. Most Kerberos princi- pals are of the form user@REALM (for example, smith@EXAMPLE.COM). Note that the Kerberos realm name must be in uppercase characters. Kerberized Applications and services that have been modified to support the Kerberos credential infrastructure. Kerberos realm A domain consisting of users, hosts, and network services that are regis- tered to a Kerberos server. The Kerberos server is trusted to verify a user’s or network service’s identity to another user or network service. Kerberos realms must always be in uppercase characters. TCP fragmentation must also be defined on the key distribution center (KDC) server. The Kerberos realm is also used to map a DNS domain to a Kerberos realm. continues
- 251. 228 Chapter 5: Security Protocols Table 5-6 Kerberos Terminology (Continued) Term Definition Kerberos server A daemon running on a network host. Users and network services register their identities with the Kerberos server. Network services query the Kerberos server to authenticate to other network services. Also known as the Master Kerberos server. Key Distribution Center A Kerberos server and database program running on a network host. (KDC) Principal Also known as a Kerberos identity, this is who you are or what a service is according to the Kerberos server. Service credential A credential for a network service. When issued from the KDC, this credential is encrypted with the password shared by the network service and the KDC, and with the user’s TGT. SRVTAB A password that a network service shares with the KDC. The network service authenticates an encrypted service credential using the SRVTAB (also known as a KEYTAB) to decrypt it. Ticket Granting Ticket A credential that the KDC issues to authenticated users. When users receive (TGT) a TGT, they can authenticate to network services within the Kerberos realm represented by the KDC. Kerberos Configuration Task List To configure Kerberos support on a Cisco router, complete the following tasks: Step 1 Define the default realm for the router: kerberos local-realm kerberos-realm Step 2 Specify to the router which KDC to use in a given Kerberos realm and, optionally, the port number that the KDC is monitoring. (The default port number is 88.) kerberos server kerberos-realm {hostname | ip-address} [port-number] Step 3 Map a host name or DNS domain to a Kerberos realm (optional): kerberos realm {dns-domain | host} kerberos-realm NOTE The kerberos local-realm, kerberos realm, and kerberos server commands are equivalent to the UNIX krb.conf file.
- 252. Virtual Private Dial-Up Networks (VPDN) 229 Example 5-12 displays a sample Kerberos configuration. Example 5-12 Kerberos Configuration kerberos local-realm CISCO.COM kerberos server CISCO.COM 3.3.3.3 kerberos realm.cisco.com CISCO.COM RADIUS and TACACS+ are far more common than Kerberos in today’s networks. Microsoft 2000, for example, uses Kerberos for internal authentication in Active Directory. NOTE For a complete guide to Kerberos, a defined and open standard, please visit the following: http://web.mit.edu/is/help/kerberos/ For UNIX experts, some of the most common UNIX executable commands when configuring and enabling Kerberos are as follows: • Kdb5_util—Allows the UNIX administrator to create the Kerberos database • Kadmin—Allows the administrator to administer the Kerberos database • Krb5kdc/kadmin—Starts the KDC daemon on the server Cisco routers support encryption and Kerberos is used. Another way for users to open a secure Telnet session is to use Encrypted Kerberized Telnet, which authenticates users by their Kerberos credentials before a Telnet session is established. The IOS command is connect host [port] /encrypt Kerberos and the exec prompt. Virtual Private Dial-Up Networks (VPDN) A VPDN is a network that extends remote access dialup clients to a private network. VPDN tunnels use either Layer 2 forwarding (L2F) or Layer 2 Tunnel Protocol (L2TP). Cisco introduced L2F in RFC 2341. It is also used to forward PPP sessions for Multichassis Multilink PPP. L2TP, introduced in RFC 2661, combines the best of the Cisco L2F protocol and Microsoft Point-to-Point Tunneling Protocol (PPTP). Moreover, L2F supports only dial-in VPDN, while L2TP supports both dial-in and dial-out VPDN. Both protocols use UDP port 1701 to build a tunnel through an IP network to forward link-layer frames.
- 253. 230 Chapter 5: Security Protocols For L2F, the setup for tunneling a PPP session consists of two steps: Step 1 Establish a tunnel between the NAS and the home gateway (HWY). The HWY is a Cisco router or access server (for example, an AS5300) that terminates VPDN tunnels and PPP sessions. This phase takes place only when no active tunnel exists between both devices. Step 2 Establish a session between the NAS and the home gateway. For L2TP, the setup for tunneling a PPP session consists of two steps: Step 1 Establish a tunnel between the L2TP access concentrator (LAC) and the L2TP network server (LNS). The LAC acts as one side of the L2TP tunnel endpoint and has a peer to the LNS. This phase takes place only when no active tunnel exists between both devices. Step 2 Establish a session between the LAC and the LNS. Figure 5-5 displays the tunnel termination points between a remote point of presence (POP) (typically an ISP router) and the home gateway router. Figure 5-5 L2F or L2TP Tunnel Termination Home Gateway Home Router Network L2F or L2TP Tunnel Remote Local POP POP ISP (IP) Network Remote Users The remote POP accepts frames encapsulated in L2F or L2TP and forwarded over the tunnel.
- 254. Virtual Private Dial-Up Networks (VPDN) 231 The LAC and LNS are hardware devices, such as Cisco’s AS 5300 series router platform. The LAC’s function is to sit between the LNS and the remote system and forward packets to and from each device. The LNS logically terminates the PPP connection. VPDNs are implemented so that users connected through ISPs in any part of the world can take advantage of the connection to the ISP and tunnel the company’s remote access traffic through the ISP network. VPDNs include the following benefits: • Access to the corporate network from a remote location. • Offload remote access services to the ISP, which already has the infrastructure place. • End system transparency because the remote user does not require any hardware or software to use VPDN. Cisco IOS routers performs all the requirements. • Allows for accounting, which is sent from the home gateway router. Figure 5-6 displays a typical VPDN scenario where a PC or router dials the NAS/LAC to request a VPDN connection to the private network. Figure 5-6 VPDN Network Scenario PC VPDN Tunnel VPDN Tunnel L2TP or L2P PSTN Telco IP Cloud Cloud NAS/LAC HGW/LNS ISDN Internal Network PC or router PPP Request NAS/LAC sends PPP request. TACACS+ Server or RADIUS Server To implement the VPDN configuration, you need the following: • A Cisco router or access server for client access (NAS/LAC) and a Cisco router for network access (HGW/LNS) with IP connectivity between them. • Host names of the routers or local names to use on the VPDN groups.
- 255. 232 Chapter 5: Security Protocols • A tunneling protocol, either the L2TP or L2F Protocol. L2TP is an industry standard, and L2F is a Cisco-proprietary protocol. • A password for the routers to authenticate the tunnel. • A tunneling criteria, either domain name or Dialed Number Identification Service (DNIS). • Username and password for the user (client dialing in). • IP addresses and keys for your TACACS+ servers. A VPDN connection between a remote user (router or through PSTN) and the corporate LAN is accomplished in the following steps: Step 1 The remote user initiates a PPP connection to the ISP using the analog telephone system or ISDN. Step 2 The ISP’s NAS accepts the connection. Step 3 The ISP NAS authenticates the end user with CHAP or PAP. The username determines whether the user is a VPDN client. If the user is not a VPDN client, the client accesses the Internet or other contacted service. Step 4 The tunnel endpoints—the NAS and the home gateway—authenticate each other before any sessions are attempted within a tunnel. Step 5 If no L2F tunnel exists between the NAS and the remote users’ home gateway, a tunnel is created. Then, an unused slot within the tunnel is allocated. Step 6 The home gateway accepts or rejects the connection. Initial setup can include authentication information required to allow the home gateway to authenti- cate the user. Step 7 The home gateway sets up a virtual interface. Link-level frames can now pass through this virtual interface through the L2F tunnel. VPDN Configuration Task List To configure VPDNs on the home gateway router, complete the following steps: Step 1 Create a virtual template interface, and enter the interface configuration mode: interface virtual-template number Step 2 Identify the virtual template interface type and number on the LAN: ip unnumbered interface number Step 3 Enable PPP encapsulation on the virtual template interface: encapsulation ppp
- 256. Virtual Private Dial-Up Networks (VPDN) 233 Step 4 Enable PPP authentication on the virtual template interface: ppp authentication {chap | ppp} Step 5 Enable the global configuration command to allow virtual private networking on the NAS and home gateway routers: vpdn enable Step 6 Specify the remote host (the NAS), the local name (the home gateway) to use for authenticating, and the virtual template to use: Home gateway router: vpdn incoming nas-name hgw-name virtual-template number NAS configuration: vpdn outgoing domain-name NAS-nameip ip ip-address NOTE You can also enable the NAS to authenticate users via TACACS+ or RADIUS using AAA commands. A typical configuration file on a UNIX server has a configuration similar to the following configuration: LAC Radius Configuration - Sample Sanjose.cisco.com Password = "cisco" Service-Type = Outbound-User, cisco-avpair = "vpdn:tunnel-id=DEFGH", cisco-avpair = "vpdn:tunnel-type=l2tp", cisco-avpair = "vpdn:ip-addresses=10.31.1.9", cisco-avpair = "vpdn:l2tp-tunnel-password=ABCDE" The configuration on the LAC defines the specific av-pairs, namely the tunnel-id, tunnel-type, ip-address, and l2tp password. Example 5-13 displays a typical NAS/LAC configuration using TACACS+. Example 5-13 Sample NAS/LAC Configuration hostname NAS-LAC ! aaa new-model aaa authentication login default local aaa authentication login CONSOLE none aaa authentication ppp default if-needed group tacacs+ aaa authorization network default group tacacs+ enable password cciesarecool ! username Melanie password 0 verysecretpassword continues
- 257. 234 Chapter 5: Security Protocols Example 5-13 Sample NAS/LAC Configuration (Continued) ! vpdn enable ! interface Ethernet0 ip address 131.108.1.1 255.255.255.0 interface Dialer1 Description USER dials in and is assigned this interface ip unnumbered Ethernet0 encapsulation ppp dialer-group 1 peer default ip address pool IPaddressPool ppp authentication chap ! ip local pool IPaddressPool 10.10.10.1 10.10.10.254 ! tacacs-server host 3.3.3.3 tacacs-server key extremelysecrtetpassword dialer-list 1 protocol ip permit line con 0 login authentication CONSOLE transport input none line 1 96 autoselect during-login autoselect ppp modem Dialin line aux 0 line vty 0 4 Example 5-13 displays the ISP router that typically supplies the tunnel-id to the HGW and IP address to the dial users. Example 5-14 displays a typical configuration the home gateway router. Example 5-14 Sample HGY/LNS Configuration hostname HGY-LNS ! aaa new-model aaa authentication login default local aaa authentication login CONSOLE none aaa authentication ppp default if-needed group tacacs+ aaa authorization network default group tacacs+ enable password cciesarecool vpdn enable ! vpdn-group DEFAULTcanbeanyname ! Default L2TP VPDN group accept-dialin protocol any virtual-template 1
- 258. Encryption Technology Overview 235 Example 5-14 Sample HGY/LNS Configuration (Continued) local name LNS lcp renegotiation always l2tp tunnel password 0 secretpwd interface Virtual-Template1 ip unnumbered FastEthernet0/0 peer default ip address pool IPaddressPool ppp authentication chap ip local pool IPaddressPool 11.11.11.1 11.11.11.254 ! tacacs-server host 3.3.3.3 tacacs-server key easypwd ! end NOTE You are not expected to demonstrate your IOS syntax knowledge for VPDN. They are presented here for completeness, along with the two sample configuration files. For more quality examples, please visit www.cisco.com/warp/public/471/#vpdn. Encryption Technology Overview When prominent Internet sites, such as www.cnn.com, are exposed to security threats, the news reaches all parts of the globe. Ensuring that data across any IP network is secure and not prone to vulnerable threats is one of today’s most challenging topics in the IP storage arena (so much so that Cisco released an entirely new CCIE certification track). Major problems for network administrators include the following: • Packet snooping (eavesdropping)—When intruders capture and decode traffic obtaining usernames, passwords, and sensitive data, such as salary increases for the year • Theft of data—When intruders use sniffers, for example, to capture data over the network and steal that information for later use • Impersonation—When an intruder assumes the role of a legitimate device but, in fact, is not legitimate The solution to these and numerous other problems is to provide encryption technology to the IP community and allow network administrators the ability to ensure that data is not vulnerable to any form of attack or intrusion. This ensures that data is confidential, authenticated, and has not lost any integrity during the routing of packets through an IP network. Encryption is defined as the process by which plain data is converted into ciphered data (a system in which plain text is arbitrarily substituted according to a predefined algorithm) so that only the intended recipient(s) can observe the data. Encryption ensures data privacy, integrity, and authentication.
- 259. 236 Chapter 5: Security Protocols Figure 5-7 displays the basic methodology behind data encryptions. Figure 5-7 Encryption Methodologies 1. 3. Data, for Encrypted data example 123... is decrypted 2. using the key. 4. Data is encrypted using mathematical formulae to scramble data. Clear text data, 123... Data is encrypted and only readable if decrypted by the correct key. Figure 5-7 demonstrates the basic principles of data encryption, including the following: Step 1 User data is forwarded over the network. Step 2 Data (clear text) is modified according to a key. The key is a sequence of digits that decrypts and encrypts messages. Typically, each device has three keys: — A private key used to sign messages that is kept secret and never shared — A public key that is shared (used by others to verify a signature) — A shared secret key that is used to encrypt data using a symmetric encryption algorithm, such as DES Step 3 A mathematical formula is applied to scramble the data. In Figure 5-7, the mathematical formula is applied during Step 2. Step 4 The data flows throughout the network and can be decrypted only if the correct key is applied. Encryption can take place at the application layer, the network layer, or the data link layer. Be aware of the following encryption technologies for the written exam: • Data Encryption Standard (DES) • Triple DES (DES3) • IP Secure (IPSec)
- 260. Encryption Technology Overview 237 Cisco IOS routers support the following industry standards to accomplish network layer encryption: • DES/3DES • Digital signature standard (DSS) • Diffie-Hellman exchange • MD5 • IPSec Data Encryption Standard (DES) and Triple Data Encryption Standard (3DES) DES is one of the most widely used encryption methods. DES turns clear text data into cipher text with an encryption algorithm. The receiving station will decrypt the data from cipher text into clear text. The encryption key is a shared secret key used to encrypt and decrypt messages. Figure 5-8 demonstrates DES encryption. Figure 5-8 DES Encryption Methodologies Data is encrypted using Encrypted Data mathematical formulae to scramble data with the $%^$%&@& shared private key. $%^$%&@& Data is encrypted using mathematical formulae to scramble data with the shared private key. Data 123... Clear Text data is received. Data 123... Figure 5-8 demonstrates the PC’s clear text generation. The data is sent to the Cisco IOS router where it is encrypted with a shared key, sent over the IP network in unreadable format until the receiving router decrypts the message and forwards in clear text form.
- 261. 238 Chapter 5: Security Protocols DES is a block cipher algorithm, which means that DES performs operations on fixed-length data streams. DES uses a 56-bit key to encrypt 64-bit datagrams. DES is a published, U.S. Government-approved encryption algorithm. 3DES is the DES algorithm that performs three times sequentially. Three keys are used to encrypted data, resulting in a 168-bit encryption key. 3DES is an improved encryption algorithm standard and is summarized as follows: • The sending device encrypts the data with the first 56-bit key. • The sending device decrypts the data with the second key, also 56 bits in length. • The sending device encrypts for a final time with another 56-bit key. • The receiving device decrypts the data with the first key. • The receiving device then encrypts the data with the second key. • Finally, the receiving devices decrypt the data with the third key. A typical hacker uses a Pentium III computer workstation and takes approximately 22 hours to break a DES key. In 3DES’s case, the documented key-breaking times are approximately 10 billion years when one million PC III computers are used. Encryption ensures that information theft is difficult. Encryption can be used to enable secure connections over the LAN, WAN, and World Wide Web. The end goal of DES/3DES is to ensure that data is confidential by keeping data secure and hidden. The data must have integrity to ensure that it has not been modified in any form, and be authenticated by ensuring that the source or destination is indeed the proper host device. The following section describes one method of making sure that data has not been tampered with— Digital Signature Standard (DSS). Digital Signature Standard (DSS) Hashing data is one method used to ensure that data has not been tampered with. Hashing involves taking a variable length of data and producing a fixed output. A HASH is defined as a one-way mathematical summary of a message (data) such that the hash value cannot be easily reconstructed into the original message. DSS is a mechanism that protects data from an undetected change while traversing the network. DSS verifies the identity of the person sending the data just as you verify your signature to a bank manager. For example, consider routing updates sent from one router to another as clear text; they are clearly visible to network sniffers or probes. Hashing and DSS can ensure that the routing updates are unreadable, except to the protected sources.
- 262. Encryption Technology Overview 239 Figure 5-9 displays the DSS signature generation that ensures data is protected from an unsecured device. Cisco IOS Router R1 is configured to send all routing updates using a hash function. Figure 5-9 DSS Signature Generation Router R1 Finally R1 sends DSS and routing updates to neighboring router, R2. Router R1 hashes the DSS Routing Update routing updates. Hashing R1 encrypts hash using + adds the private key. private key and creates a DSS signature. = signature Router R2 Neighboring router receives IP routing updates. Routing updates are prone to network sniffers. By hashing the routing updates, as shown in Figure 5-9, the routing networks exchanged between Cisco IOS routers can be protected from unsecured devices. The steps to ensure that network routing updates (in Figure 5-9) are secure follow: Step 1 Router R1 hashes the routing update. (Cisco IOS routers can use MD5). Step 2 R1 encrypts the hashed routing update using its own private key. Step 3 R1 appends the routing update with the DSS. Step 4 The DSS is verified by neighboring router, R2. Step 5 R2 decrypts the DSS using R1’s own public key and obtains the hash that was originally generated by R1. Step 6 R2 compares the hash received from R1 with the hash it just generated. If they are the same, the routing update is assured legitimate and was not modified by any network intruder. Message Digest 5 (MD5) and Secure Hash Algorithm (SHA) Several hashing algorithms are available. The two discussed here are MD5 and SHA (sometimes called SHA-1).
- 263. 240 Chapter 5: Security Protocols Message hashing is an encryption technique that ensures a message or data has not be tampered with or modified. MD5 Message hashing is supported on Cisco IOS routers. A variable-length message is taken, the MD5 algorithm is performed (for example, the enable secret passwords command), and a final fixed-length hashed output message is produced. MD5 is defined in RFC 1321. Figure 5-10 displays the MD5 message operation. Figure 5-10 MD5 Operation Clear Text message of variable length "Hello, it’s me" MD5 hash algorithm MD5 applied here. Unreadable message is now hashed, fixed length. 4w5645968234t43ty34t5n 45y654y67365346316464n Figure 5-10 displays the simple clear text message, “Hello, it’s me,” which can be of any variable length. This message is sent to the MD5 process, where the clear text message is hashed and a fixed-length, unreadable message is produced. The data can include routing updates or username/password pairings, for example. MD5 produces a 128-bit hash output. Secure Hash Algorithm (SHA) is the newer, more secure version of MD5, and Hash-based Message Authentication (HMAC) provides further security with the inclusion of a key exchange. SHA produces a 160-bit hash output, making it even more difficult to decipher. SHA follows the same principles as MD5 and is considered more CPU-intensive. For more details on Cisco IOS encryption capabilities, please visit the following website: www.cisco.com/en/US/tech/tk583/tk209/tech_protocol_family_home.html Diffie-Hellman The Diffie-Hellman protocol allows two parties to establish a shared secret over insecure channels, such as the Internet. This protocol allows a secure shared key interchange over the public network, such as the World Wide Web, before any secure session and data transfer is initiated. The Diffie-Hellman ensures that by exchanging just the public portions of the key, both devices can generate a session and ensure data is encrypted and decrypted by valid sources only. Only public keys (clear text) are exchanged over the public network. Using each device’s
- 264. Encryption Technology Overview 241 public key and running the key through the Diffie-Hellmann algorithm generates a common session key. Only public keys will ever be exchanged. Figure 5-11 displays the Diffie-Hellman exchange between Cisco routers, R1 and R2. Figure 5-11 Diffie-Hellman Key Exchange R1 Private Key and 1 R1 Private Key and Public Key 1. Public keys are exchanged Public Key in clear text. 2. Random Integer 2 2. Random Integer generated. generated. 3 + prime number "A" + prime number "B" 3.Each router uses the random integer to generate a private key. 4 4. R1 and R2 then combine with the known prime number A and B to generate a public key. Shared Secret The Diffie-Hellman key exchange takes place over a public domain. With the private key secret, it is very difficult for an outside intruder to generate the same key, and the private key is never exchanged over the public domain, making the process very secure. The shared prime numbers (mathematically, this means any positive integer greater than 1 and divisible without a remainder only by 1 and itself) have a special relationship that makes agreeing on a shared secret possible. An analogy would be to have two milkshake blenders making a chocolate milkshake, but with one blender supplied with apples and the other with oranges. The Diffie-Hellman algorithm is the secret ingredient that, when mixed in with both blenders, produces the chocolate milkshake. Remember, it really is a superb algorithm. NOTE RSA is another public key cryptographic algorithm (named after its inventors, Rivest, Shamir, and Adleman) with a variable key length. RSA’s main weakness is that it is significantly slow to compute compared to popular secret-key algorithms, such as DES or 3DES. Cisco’s IKE implementation uses a Diffie-Hellman exchange to get the secret keys. This exchange can be authenticated with RSA (or pre-shared keys). With the Diffie-Hellman exchange, the DES key never crosses the network, which is not the case with the RSA encryption and signing tech- niques. RSA is not public domain like DES/3DES, and to apply RSA, you must be licensed from RSA Data Security. An RSA signature is defined as the host (for example PC or routers) public and private key, which is bound with a digital certificate.
- 265. 242 Chapter 5: Security Protocols IP Security IPSec IPSec provides security services at the IP layer by enabling a system to select required security protocols, determine the algorithm(s) to use for the service(s), and put in place any cryptographic keys required to provide the requested services. RFC 2401 for IP IPSec is a defined encryption standard that encrypts the upper layers of the OSI model by adding a new predefined set of headers. A number of RFCs defined IPSec. IPSec is a mandatory requirement for IP version 6. (IPV6 is not covered in the examination.) IPSec ensures that the network layer of the OSI model is secured. In TCP/IP’s case, this would be the IP network layer. IPSec can be configured in two protection modes, which are commonly referred to as Security Association (SA). These modes provide security to a given IP connection. The modes are as follows: • Transport mode—Protects payload of the original IP datagram; typically used for end- to-end sessions • Tunnel mode—Protects the entire IP datagram by encapsulating the entire IP datagram in a new IP datagram SA is required for inbound and outbound connection. In other words, IPSec is unidirectional. IKE, discussed in this chapter, allows for bidirectional SAs. Figure 5-12 displays the extension to the current IP packet frame format for both transport and tunnel modes. Figure 5-12 IPSec Protection Modes Original IP Datagram IP Header IP Data (Not Encrypted) Transport IPSec IP Header Data (Encrypted) Mode Header New IP Header Encrypted Tunnel New IP IPSec Original Data Mode Header Header Header IP Header IP Data (Not Encrypted) Original IP Datagram
- 266. Encryption Technology Overview 243 The encapsulation security payload (labeled IPSec header in Figure 5-12) can be of two forms: • Encapsulation Security Payload (ESP) • Authentication Header (AH) Each of these is discussed in the following sections. Encapsulation Security Payload (ESP) The ESP security service is defined in RFC 2406. ESP provides a service to the IP data (pay- load), including upper-layer protocols such as TCP. The destination IP port number is 50. The ESP header is located between the user data and original IP header, as displayed in Figure 5-13. Figure 5-13 displays the ESP header. Figure 5-13 ESP Header IP HDR ESP IP Data Authenticated Encrypted ESP does not encrypt the original IP header, and encrypts only the IP data by placing a header in between the original IP header and data. ESP provides data confidentiality, data integrity, and data origin authentication. ESP also prevents replay attacks. Replay attacks can include intruders capturing a valid packet and replaying it over the network in an attempt to get a packet conversation between an illegal and legal host. ESP does not protect the IP header and cannot ESP detect any alternations during packet delivery. Figure 5-14 displays the frame formats when ESP is applied. The Security Parameters Index (SPI) is an arbitrary 32-bit value that, in combination with the destination IP address and security protocol (ESP), uniquely identifies the Security Association for this datagram. The sequence number, an unsigned 32-bit field, contains a monotonically increasing counter value. It is mandatory and is always present, even if the receiver does not elect to enable the antireplay service for a specific SA. Pad or padding is used when the frame needs to meet the minimum frame size formats. The pad length defines the length of padding used. Padding is used for a number of reasons. For example, padding can ensure that the minimum frame size is set so that packets are not discarded because they are too small. Padding is typically all binary ones (1111. . .) or zeros (0000. . .). The sequence number ensures that no intruder or intruders can replay data transactions by using any form of attack mechanisms.
- 267. 244 Chapter 5: Security Protocols Figure 5-14 ESP Frame Format IP Header (Port 50) Security Parameter Index (SPI) Sequence Number Payload Data (variable) PAD (0-255 bytes) Authenticated PAD Length Next Header Encrypted IP Data Authentication Data The Next Header is an 8-bit field that identifies the type of data contained in the Payload Data field. The IP data field contains the data to be sent. The Authentication Data field is a variable- length field containing an Integrity Check Value (ICV) computed over the ESP packet minus the Authentication Data. Authentication Header (AH) AH is described in RFC 2402. The IP protocol destination port is 51. Figure 5-15 highlights the fields in the IP datagram that are encrypted and authenticated. Note that not all fields, such as the Time to Live fields, are encrypted. NOTE AH provides data origin authentication and optional replay-detection services. AH doesn’t provide data confidentiality (or encryption). Authentication is done by applying one-way hash to create a message digest of the packet. Replay detection can be implemented using the sequence number in the IP packet header.
- 268. Encryption Technology Overview 245 Figure 5-15 AH Header Fields protected by AH Unprotected (variable) Fields Ver Le ToS Total Length ID Flags, Fragment TTL Protocol Header Checksum Source IP Address AH Header Destination IP Address IP Header (Port 51) AH Header Next Payload Header Length Reserved TCP/UDP Header Encrypted Security Parameter Index (SPI) Payload Sequence Number Authentication Data Following is a description of an AH packet: • Next Header, an 8-bit field, identifies the type of the next payload after the Authentication Header. • The Payload Length field is an 8-bit field specifying AH’s length in 32-bit words (4-byte units), minus 2. • The Reserved field is a 16-bit field reserved for future use. It MUST be set to 0. • The SPI is an arbitrary 32-bit value that, in combination with the destination IP address and security protocol (AH), uniquely identifies the Security Association for this datagram. AH can operate in transport or tunnel mode; however, contrary to ESP, AH also protects fields in the outer IP Header (in transport mode, this is the original IP header; in tunnel mode, this is the newly added IP header), which are normally considered nonvariable. AH ensures that if the original IP header has been altered, the packet is rejected.
- 269. 246 Chapter 5: Security Protocols Before you take a look at how IPSec is enabled on Cisco routers, you need to understand how keys are exchanged between secure devices to ensure that data is not comprised. IPSec ensures that once an IPSec tunnel is created, that the keys are modified so intruders cannot replicate the keys and create IPSec tunnels to insecure locations. A recent study showed that a network of computer hackers was able to decipher a DES-encrypted message in just a day. In IPSec, this function is provided by Internet Key Exchange (IKE). IKE is discussed in the next section. Internet Key Exchange (IKE) In IPSec, a SA between any two devices will contain all relevant information such, as the cryptographic algorithm in use. A cryptographic algorithm is the science of cryptography. This field of science includes the exact details of encryption algorithms, digital signatures, and key agreement algorithms. A simple two-router network requires four SAs, two for each router. (IPSec requires two SAs on each router for two-way communication.) Clearly, for a large network, this would not scale. IKE offers a scalable solution to configuration, and key exchange management. IKE was designed to negotiate and provide authenticated keys in a secure manner. IKE has two phases. In phase I, the cryptographic operation involves the exchange of a master secret where no security is currently in place. IKE phase I is primarily concerned with estab- lishing the protection suite for IKE messages. Phase I operations are required infrequently and can be configured in two modes of operation—aggressive and main mode. Aggressive mode eliminates several steps during IKE authentication negotiation phase I between two or more IPSec peers. Aggressive mode is faster than main mode but not as secure. Aggressive mode is a three-way packet exchange, while main mode is a six-way packet exchange. IKE can be configured in aggressive mode or main mode (not both). Aggressive mode is a less intensive process that requires only three messages to establish a tunnel rather than six in main mode. Aggressive mode is typically used in dialup environments. NOTE Cisco devices use main mode but can respond to peers using aggressive mode.
- 270. Internet Key Exchange (IKE) 247 IKE Phase I Messages Types 1-6 IKE phase I completes the following tasks: • Negotiates IKE policy (message types 1 and 2). Information exchanges in these message types include IP addresses. Proposals, such as Diffie-Hellman group number and encryption algorithm, are also exchanged here. All messages are carried in UDP packets with a destination UDP port number of 500. The UDP payload comprises a header, an SA payload, and one or more proposals. Message type 1 offers many proposals, and message type 2 contains a single proposal. • Performs authenticated Diffie-Hellman exchange (message types 3 and 4). Messages type 3 and 4 carry out the Diffie-Hellman (DH) exchange. Messages type 3 and 4 contain the key exchange payload, which is the DH public value and a random number. Messages type 3 and 4 also contain the remote peer’s public key hash and the hashing algorithm. A common session key created on both ends, and the remaining IKE messages exchanged from here are encrypted. If perfect forward secrecy (PFS) is enabled, another DH exchange will be completed. • Protects IKE peers’ identities—identities are encrypted. Message types 5 and 6 are the last stage before traffic is sent over the IPSec tunnel. Message type 5 allows the responder to authenticate the initiating device. Message type 6 allows the initiator to authenticate the responder. These message types are not sent as clear text. Messages type 5 and 6 will now be encrypted using the agreed upon encryption methods established in message types 1 and 2. After IKE phase I is completed, each peer or router has authenticated itself to the remote peer, and both have agreed on the characteristics of all the SA parameters. Figure 5-16 summarizes the key components of IKE phase I and some of the possible permutations available on Cisco IOS routers. The first message exchanged offers the remote router a choice of IPSec parameters, such as encryption algorithm, 3DES, MD5, and DH group number, for example. The first message’s aim is to negotiate all SA policies and generate the shared secret. In the second message (type 2), the responding device indicates which of the IPSec parameters it wants to use in the tunnel between the two devices, including the information required to generate the shared secret and provide authentication details. The final message (type 3; until now no encryption is enabled), which might or might not be encrypted, authenticates the initiator. After IKE phase I is complete, IKE phase II is initiated. As discussed in the following section, IKE phase II negotiation has three message types.
- 271. 248 Chapter 5: Security Protocols Figure 5-16 IKE Phase I Summary IKE Phase 1 Summary Examples include: This peer wants DES, MD5, DES, MD5, RSA Encryption, DH2 or Pre-shared keys, DH2 DES, MD5, Pre-shared Keys, DH2 IPSec Tunnel Initiator Remote peer IKE Phase 1 IKE SA Parameters IKE SA Parameters DES DES MD5 MD5 Pre-share Pre-share DH2 DH2 Lifetime Lifetime • Negotiates IKE policy • Performs authenticated Diffie-Hellman exchange • Provides protection of identities of IKE peers • Finally data can be transferred IKE Phase II Message Types 1-3 IKE phase II negotiates the SA and the keys that will be used to protect the user data. IKE phase II messages occur more frequently and typically every few minutes, where IKE phase I messages might occur once a day. IP datagrams that exchange IKE messages use UDP (connectionless) destination port 500. Phase II negotiations occur in a mode called Oakley quick mode and have three different message exchanges. Quick mode can be the following: • Without key exchange—No PFS enabled. • With Key exchange—When PFS is enabled, the DH algorithm is run once more to generate the shared secret. Message type I allows the initiator to authenticate itself and selects a random (nonce) number and proposes a security association to the remote peer. Additionally, a public key is provided (can be different than a key exchanged in IKE phase I). IKE phase II message type II allows the responding peer to generate the hash. Message type 2 allows the responder to authenticate itself, and selects a random number and accepts the SA offered by the initiating IPSec peer. IKE Message type III acknowledges information sent from quick mode message 2 so that the phase II tunnel can be established.
- 272. Internet Key Exchange (IKE) 249 NOTE Perfect forward secrecy can be requested as part of the IKE security association. PFS ensures that a given IPSec SA key was not derived from any other secret (like some other keys). In other words, if someone were to break a key or get the key used between two peers, PFS ensures that the attacker would not be able to derive any other key. If PFS was not enabled, someone could hypothetically break the IKE SA secret key, copy all the IPSec protected data, and use knowledge of the IKE SA secret to compromise the IPSec Sa’s setup by this IKE SA. With PFS, breaking IKE would not give an attacker immediate access to IPSec. The attacker would have to break each IPSec SA individually. Changing the secret key being used for encryption after some period of time (or after a specified number of bytes have been encrypted) is a good idea. Changing keys makes it more difficult for an attacker to derive the key or the new created key. Now that all the required data has been exchanged, the initiating IPSec router, or peer, sends a final phase I message with the hash of the two random numbers generated and the message ID. Figure 5-17 summarizes the key components of IKE phase II. Figure 5-17 IKE Phase II Summary IKE Phase 2 Summary IPSec Tunnel IPSec SA IKE Phase 2 IPSec SA Peer Peer 3DES 3DES SHA SHA ESP ESP Lifetime Lifetime • Negotiates IPSec SA parameters protected by an existing IKE SA (during IKE phase 1) • Establishes IPSec security associations, SA • Periodically renegotiates IPSec SAs to ensure security • Optionally performs an additional Diffie-Hellman exchange if PFS enabled Figure 5-18 displays a typical IKE phase I/II completion. IKE negotiates policy to protect the communication authenticated key exchange and SAs for IPSec.
- 273. 250 Chapter 5: Security Protocols Figure 5-18 IKE Phase I/II Steps Phase I/II • Establish ISAKMP SA • Negotiate ISAKMP SA policies such as encryption (MD5, 3DES, DSS) • Exchange information needed to generate shared key • Perform Diffie-Hellman calculation (shared secret) • Generate the keys (pre-shared, DSS public keys) • Communication can now begin by testing decryption IKE Protocol IKE Peers IKE Peers Transform, Transform, Host A key material key material Host B IPSec Protocols ESP or AH IPSec Tunnel Table 5-7 summarizes the key components of IKE phase I and II. Table 5-7 IKE Phase I/II Phase Components IKE phase I Authenticates IPSec peers, negotiates matching policy to protect IKE exchange, exchanges keys via Diffie-Hellman, and establishes the IKE SA. IKE phase II Negotiates IPSec SA parameters by using an existing IKE SA. Establishes IPSec security parameters. Periodically renegotiates IPSec SAs to ensure security and that no intruders have discovered sensitive data. Can also perform optional additional Diffie-Hellman exchange. IKE requires that all information exchanges be encrypted and authenticated. In addition, IKE is designed to prevent the following attacks: • Denial of Service—When messages are constructed with unique cookies that can be used to identify and reject invalid messages. • Man in the middle—Prevents the intruder from modifying messages and reflecting them back to the source or replaying old messages. NOTE Access lists determine what traffic to encrypt. For example, you can specify that certain networks are to be encrypted and other networks are not. The permit statement encrypts data, and the deny statement (implicit) in an ACL does not send traffic encrypted. An ACL applied to IPSec configuration parameters does not stop IP routing on a Cisco IOS router.
- 274. Internet Key Exchange (IKE) 251 Table 5-8 summarizes the key terms and concepts used in IPSec terminology. Table 5-8 Summary IPSec Terms and Concepts Attribute Meaning IKE The IKE protocol provides utility services for IPSec, such as authentication of peers, negotiation of IPSec SAs, and encryption algorithms. IKE operates over the assigned UDP port 500. SA Security associations are connections between IPSec peers. Each IPSec peer maintains an SA database containing parameters, such as peer address, security protocol, and security parameter index (SPI). DES Data Encryption Standard. DES encrypts and decrypts data. Not considered a strong algorithm and replaced by 3DES. DES only supports a 56-bit key. 3DES supports 3×56, or a 168-bit key. 3DES A variant of DES and much stronger encryption method that uses a 168-bit key. MD5 Message Digest version 5 is a hash algorithm that takes an input message (of variable length) and produces a fixed-length output message. IKE uses MD5 for authentication purposes. SHA-1 Secure Hash Algorithm that signs and authenticates data. It is stronger than MD5 but more CPU-intensive and, therefore, slower. RSA signatures RSA is a public-key encryption system used for authentication. Users are assigned both private and public keys. The private key is not available to the public and decrypts messages created with the public key. CA Certification authority is an entity that provides digital certificates and binds data items within a certificate. Figure 5-19 displays the flow chart before any data can be transferred between two IPSec peers. Figure 5-19 IPSec flow R1 Interesting Traffic Received R1 1. IKE 2. IPSec Tunnel 3. Data Flow
- 275. 252 Chapter 5: Security Protocols In Figure 5-19, interesting traffic (or traffic from an end user, for example) triggers the IKE phases I/II followed by the establishment of the IPSec tunnel. After the IPSec tunnel is estab- lished, the data can be transferred. After the data is transferred, the IPSec tunnel is closed. You can tunnel any form of data across the IPSec tunnel, such as IP, Novel IPX, or AppleTalk. Cisco IOS IPSec Configuration To enable IPSec between Cisco IOS routers, the following steps are required: Step 1 Enable ISAKMP with the IOS command crypto isakmp enable. This step globally enables or disables ISAKMP at your peer router. ISAKMP is enabled by default (optionally, define what interesting traffic will be encrypted using defined access lists). Step 2 Define an ISAKMP policy, a set of parameters used during ISAKMP negotiation: crypto isakmp policy priority You will enter config-isakmp command mode. Options available include the following: Router(config-isakmp)#? authentication {rsa-sig | rsa-encr | pre-share} default encryption {des} exit group hash {md5 | sha} lifetime seconds no This command invokes the Internet Security Association Key Management Protocol policy configuration (config-isakmp) command mode. While in the ISAKMP policy configuration command mode, the following commands are available to specify the parameters in the policy: — Encryption (IKE policy)—The default is 56-bit DES-CBC. To specify the encryption algorithm within an Internet Key Exchange policy, options are des or 3des. — Hash (IKE policy)—The default is SHA-1. To specify the hash algorithm within an Internet Key Exchange policy, options are sha, which specifies SHA-1 (HMAC variant) as the hash algorithm, or md5, which specifies MD5 (HMAC variant) as the hash algorithm. — Authentication (IKE policy)—The default is RSA signatures. To specify the authentication method within an Internet Key Exchange policy, options are rsa-sig, which specifies RSA signatures as the
- 276. Internet Key Exchange (IKE) 253 authentication method, rsa-encr, which specifies RSA encrypted as the authentication method, or pre-share, which specifies pre-shared keys as the authentication method. — Group {1|2}—The default is 768-bit Diffie-Hellman. To specify the Diffie-Hellman group identifier within an Internet Key Exchange policy, options are 1, which specifies the 768-bit Diffie-Hellman group, or 2, which specifies the 1024-bit Diffie-Hellman group. — Lifetime (IKE policy)—The default is 86,400 seconds (once a day). To specify the lifetime of an Internet Key Exchange security association (SA), use the Lifetime Internet Security Association Key Management Protocol policy configuration command. If two IPSec peers share different lifetime values, the chosen value is the shortest lifetime. Step 3 Set the ISAKMP identity (can be IP address or host name based). crypto isakmp identity {address | hostname} Step 4 Define transform sets. A transform set represents a combination of security protocols and algo- rithms. During the IPSec security association negotiation, the peers agree to use a particular transform set for protecting a particular data flow. To define a transform set, use the following commands starting in global configuration mode: crypto ipsec transform-set transform-set-name transform1 [transform2 [transform3]] This command puts you into the crypto transform configuration mode. Then define the mode associated with the transform set. Router(cfg-crypto-tran)# mode [tunnel | transport] Step 5 Define crypto maps. Crypto maps tie the IPSec policies and SAs together. crypto map name seq method [dynamic dynamic-map-name] NOTE Crypto map entries created for IPSec pull together the various parts used to set up IPSec SAs, including the following: • Which traffic should be protected by IPSec (per a crypto access list) • The granularity of the flow to be protected by a set of SAs • Where IPSec-protected traffic should be sent (who the remote IPSec peer is) • The local address to be used for the IPSec traffic
- 277. 254 Chapter 5: Security Protocols • What IPSec security should be applied to this traffic • Whether SAs are manually established or are established through IKE • Other parameters that might be necessary to define an IPSec SA A dynamic crypto map entry is essentially a crypto map entry without all the parameters configured. It acts as a policy template where the missing parameters are later dynamically configured (as the result of an IPSec negotiation) to match a remote peer’s requirements. This allows remote peers to exchange IPSec traffic with the router even if the router does not have a crypto map entry specifically configured to meet all the remote peer’s requirements. Dynamic crypto maps are typically used to ensure security between a dialup IPSec client and Cisco IOS router, for example. The following typical configuration scenario illustrates the IPSec configuration tasks with a two-router network. Figure 5-20 displays two routers configured with the networks 131.108.100.0/24 and 131.108.200.0/24, respectively. Suppose the Frame relay cloud is an unsecured network and you want to enable IPSec between the two routers, R1 and R2. The network administrator has decided to define the following ISAKMP parameters: • MD5 • Authentication will be pre-share • The shared key phrase is CCIE • IPSec mode is transport mode Figure 5-20 Typical IPSec Topology Between Two Remote Routers IKE Protocol IKE Peers IKE Peers Host A Host B 131.108.255.0/24 IPSec Tunnel 131.108.100.0/24 131.108.200.0/24 access-list 100 permit ip Mirrored ACLs access-list 100 permit ip 131.108.100.0 0.0.0.255 131.108.200.0 0.0.0.255 131.108.200.0 0.0.0.255 131.108.100.0 0.0.0.255
- 278. Internet Key Exchange (IKE) 255 To start, configure IKE on Router R1. Example 5-15 displays the IKE configuration on R1. Remember that IKE policies define a set of parameters to be used during IKE negotiation. Example 5-15 R1 IKE Configuration crypto isakmp policy 1 hash md5 authentication pre-share crypto isakmp key CCIE address 131.108.255.2 R1 is configured to use the MD5 algorithm, and the authentication method is defined as pre- shared. The pre-share key value (password) is CCIE, and the remote IPSec peer’s address is 131.108.255.2 (R2 Serial Link to R1 in Figure 5-20). Pre-shared Keys Versus Manual Keys The example shown here is an example of pre-shared keys whereby IKE is used to negotiate all SA parameters. You can also define IPSec not to use IKE, and this is referred to as manual IPSec or manual keys. Cisco strongly recommends that you use IKE or pre-shared keys because it is very difficult to ensure that all SA parameters are matching between remote peers. The Diffie- Hellman algorithm is a more secure method when generating secret keys between peers. Manual keys are prone to intruders and unauthorized sources that gain entry to Cisco configu- ration files. Another major disadvantage of manual keys is that the IOS crypto map command used to establish SAs does not expire. Following the IKE configuration, you can configure IPSec parameters. Example 5-16 enables the IPSec configuration parameters. Example 5-16 IPSec Configuration crypto ipsec transform-set anyname esp-des esp-sha-hmac mode transport ! crypto map anyname1 1 ipsec-isakmp set peer 131.108.255.2 set security-association lifetime seconds 180 set transform-set anyname match address 100 ! access-list 100 permit ip 131.108.100.0 0.0.0.255 131.108.200.0 0.0.0.255 The transform set command defines an acceptable combination of security protocols and algorithms. This example applies ESP-DES (ESP with the 56-bit DES encryption algorithm) and ESP with the SHA (HMAC variant) authentication algorithm. The next-hop peer address is
- 279. 256 Chapter 5: Security Protocols defined and access-list 100 defines what traffic will be encrypted. In Figure 5-20, only IP traffic sourced from 131.108.100.0 destined for 131.108.200.0/24 is sent across the IPSec tunnel. Example 5-17 displays the configuration on R2. Example 5-17 R2 IKE and IPSec Configuration ! IKE configuration crypto isakmp policy 1 hash md5 authentication pre-share crypto isakmp key CCIE address 131.108.255.1 ! crypto ipsec transform-set anyname esp-des esp-sha-hmac mode transport !IPSec configuration crypto map anyname1 1 ipsec-isakmp set peer 131.108.255.1 set security-association lifetime seconds 180 set transform-set anyname match address 100 !Access list defines traffic to be encrypted access-list 100 permit ip 131.108.200.0 0.0.0.255 131.108.100.0 0.0.0.255 Notice that the routers have mirrored access lists. This ensures that when encrypted data is received from a source, such as R1, the corresponding IPSec peer router, R2, enables encryption in the reverse direction. For example, when traffic from the network 131.108.100.0/24 residing on Router R1 is sent across destined for R2’s Ethernet network, the IP subnet 131.108.200.0/24, R2 must have a corresponding ACL permitting traffic from the locally-connected Ethernet segment, 131.108.200.0/24, to the remote network, the IP subnet on R1, 131.108.100.0/24. This is referred to as mirrored access lists. Example 5-17 configures R2 to peer to R1 and only encrypt traffic sourced from 131.108.200.0/24 destined for R1’s Ethernet network, 131.108.100.0/24. The crypto predefined map name is anyname1. Finally, you must apply a previously defined crypto map (in our example the name defined is anyname1) in Example 5-16. The defined crypto map name is anyname1, so apply that config- uration to the interface. The IOS command that applies the crypto map to an interface is as follows: crypto map anyname1 Example 5-18 assigns the serial links on R1 and R2 the crypto map name anyname1.
- 280. Internet Key Exchange (IKE) 257 Example 5-18 assigns the crypto map to interface Serial 0/0 on R1/R2. Example 5-18 Serial Links and crypto map on R1/R2 Hostname R1 ! interface Serial0/0 ip address 131.108.255.1 255.255.255.252 crypto map anyname1 ! Hostname R2 ! interface Serial0/0 ip address 131.108.255.2 255.255.255.252 crypto map anyname1 To display the status of all crypto engine active connections, use the IOS command show crypto engine connections active. Example 5-19 displays the current active crypto engines on R1. Example 5-19 show crypto engine connections active on R1 R1#show crypto engine connections active ID Interface IP-Address State Algorithm Encrypt Decrypt 1 Serial0/0 131.108.255.1 set HMAC_MD5+DES_56_CB 5 5 R1 has an IPSec peer connection to R2, through the Serial0/0 interface (131.108.255.1). The algorithm in use is defined and displayed, as well. To view the crypto map configuration from the privilege prompt, use the IOS command show crypto map. Example 5-20 displays the configuration present on R1. Example 5-20 show crypto map on R1 R1#show crypto map Crypto Map "anyname1" 1 ipsec-isakmp anyname1 Peer = 131.108.255.2 Extended IP access list 100 access-list 100 permit ip 131.108.100.0 0.0.0.255 131.108.200.0 0.0.0.255 Current peer: 131.108.255.2 Security association lifetime: 4608000 kilobytes/180 seconds PFS (Y/N): N Transform sets={ anyname, } Interfaces using crypto map anyname1: Serial0/0
- 281. 258 Chapter 5: Security Protocols Example 5-20 displays the fact that the crypto map named “MAP1” is peered to a remote router, 131.108.255.2, and the access-list 100 defines what traffic will be encrypted across the tunnel. IPSec is a large field, and to define every possible scenario would require a book in itself. What is presented here in this guide is a conceptual overview of IPSec and a common configuration example. For more extensive details, visit www.cisco.com/univercd/cc/td/doc/product/software/ ios122/122cgcr/fsecur_c/index.htm. For the written exam, expect to see scenarios of the variant presented in Figure 5-20 and questions on terminology and the main characteristics of IPSec. NOTE IPSec can also be supported over the Cisco software tunnel interface. Typically, the tunnel (IP tunnel; GRE, for example) can be configured to carry non-IP traffic by defining a crypto map to the tunnel interface and a crypto control list. Table 5-9 defines some key configuration show and debug IPSec commands available on Cisco IOS routers. Table 5-9 IOS IPSec Configuration, Show, and Debug Commands Command Description crypto map map-name seq-num ipsec-isakmp Creates a crypto map entry. [dynamic dynamic-map-name] [discover] crypto ipsec transform-set transform-set-name Defines a transform set, an acceptable combination transform1 [transform2 [transform3]] of security protocols and algorithms. match address [access-list-id | name] This command is required for all static crypto map entries. crypto dynamic-map dynamic-map-name Use dynamic crypto maps to create policy dynamic-seq-num templates that can be used when processing negotiation requests for new SAs from a remote IP Security peer, even if you do not know all the crypto map parameters. crypto ca authenticate name This command is required when you initially configure CA support at your router. crypto ca identity name Use this command to declare a CA. crypto isakmp enable Globally enables Internet Key Exchange (IKE) at your peer router. Show crypto engine connection active View phase II SA and traffic sent.
- 282. Certificate Enrollment Protocol (CEP) 259 Table 5-9 IOS IPSec Configuration, Show, and Debug Commands (Continued) Command Description authentication {rsa-sig | rsa-encr | pre-share} Specifies the authentication method within an IKE policy. show crypto ipsec sa Use this command to view the settings used by current SAs to declare a CA. show crypto map This command views the crypto map configuration. show crypto isakmp sa This command views all current IKE SAs at a peer. debug crypto engine Use this command to display debug messages about crypto engines, which perform encryption and decryption. debug crypto ipsec Use this command to display IPSec events. debug crypto pki messages This command displays debug messages for the details of the interaction (message dump) between the CA and the router. NOTE A number of PC-based applications are available to the public that allow application layer encryptions. An excellent e-mail encryption application is a product called Pretty Good Privacy (PGP). Designed and freely available on the Internet (www.pgp.com/), PGP allows users to authenticate files and e-mail text, allowing only the intended recipient the ability to decrypt the message. Users who send and receive encrypted data exchange keys. With encrypted data, the remote user’s key is used to encrypt clear text data or files. This ensures that the data is authenticated and not forged. Microsoft Outlook 2000 supports PGP and allows the client to encrypt and decrypt data using the pre-shared private keys. Certificate Enrollment Protocol (CEP) CEP is a protocol jointly developed by Cisco and Verisign, Inc. CEP is an early implementation of Certificate Request Syntax (CRS), a proposed standard to the IETF. CEP specifies how a device communicates with the CA, how to retrieve the CA’s public key, and how to enroll a device with the CA. CEP uses Public Key Cryptography Standards (PKCS). CEP uses HTTP as a transport mechanism and uses the same TCP port (80) used by HTTP. To declare the CA that a Cisco IOS router should use, use the crypto ca identity <name> command in global configuration mode. The CA might require a particular name, such as the domain name.
- 283. 260 Chapter 5: Security Protocols Foundation Summary The “Foundation Summary” is a condensed collection of material for a convenient review of key concepts in this chapter. If you are already comfortable with the topics in this chapter and decided to skip most of the “Foundation Topics” material, the “Foundation Summary” will help you recall a few details. If you just read the “Foundation Topics” section, this review should help further solidify some key facts. If you are doing your final preparation before the exam, the “Foundation Summary” offers a convenient and quick final review. Table 5-10 AAA Terminology Attribute Meaning Authentication Who are you? A remote user must be authenticated before being permitted access to network resources. Authentication allows users to submit their usernames and passwords, and permit challenges and responses. Username/Password pairs are a common form of authentication. Authorization What resources are you permitted? Once the user is authenticated, authorization defines what services in the network are permitted access. The operations permitted here can include IOS privileged exec commands. Accounting What resources were accessed, what times were they accessed, by whom were they accessed, and what commands were issued to access them? Accounting allows the network administrator to log and view what was actually performed. For example, if a Cisco router was reloaded or the configuration was changed. Accounting ensures that an audit will allow network administrators the ability to view what was performed and at what time. Table 5-11 RADIUS Summary Feature Meaning UDP Packets sent between clients and servers are UDP primarily because TCP’s overhead does not allow for significant advantages. Typically, the user can wait for a username/password prompt. UDP 1812, port 1646 used for accounting. RADIUS is an industry standard defined in destination port RFC 2138. Attributes Attributes are used to exchange information between the NAS and client. Model Client/server-based model where packets are exchanged in a unidirectional manner. Encryption Password is encrypted using MD5; the username is not. RADIUS encrypts only the method password in the access-request packet from the client to the server. The remainder of the packet is in clear text. A third party could capture other information, such as username, authorized services, and accounting. Multiprotocol Does not support protocols such as AppleTalk, NetBIOS, or IPX. IP is the only support protocol supported.
- 284. Foundation Summary 261 Table 5-12 TACACS+ Summary Feature Meaning TCP Packets sent between client and server are TCP. Typically, the user can wait for a username/password prompt. TCP destination port Port 49. Attributes Packet types are defined in TACACS+ frame format as: Authentication 0x01 Authorization 0x02 Accounting 0x03 Seq_no The sequence number of the current packet flow for the current session. The Seq_no starts with 1 and each subsequent packet will increment by one. The client only sends odd numbers. TACACS+ servers only send even numbers. Encryption method The entire packet is encrypted. Data is encrypted using MD5 and a secret key that matches both on the NAS (for example, a Cisco IOS router) and the TACACS+ server. Multiprotocol support Supports protocols such as AppleTalk, NetBIOS, or IPX. IP-supported only. Table 5-13 RADIUS Versus TACACS+ RADIUS TACACS+ Packet delivery UDP TCP Packet encryption RADIUS encrypts only the password TACACS+ encrypts the entire body in the access-request packet from the of the packet, but leaves a standard client to the server. TACACS+ header. AAA support RADIUS combines authentication TACACS+ uses the AAA and authorization. architecture, separating authentication, authorization, and accounting. Multiprotocol support None. Supports other protocols, such as AppleTalk, NetBIOS, and IPX. Router management RADIUS does not allow users to TACACS+ allows network control which commands can be administrators control over which executed on a router. commands can be executed on a router.
- 285. 262 Chapter 5: Security Protocols Table 5-14 Summary of Kerberos Protocol Attribute Meaning Packet delivery A number of ports are defined: TCP/UDP ports 88, 543, and 749 TCP ports 754, 2105, and 4444 Packet encryption Supports username/password encryption. Telnet sessions are encrypted, for example. AAA support RADIUS combines authentication and authorization. Server support Typically runs on a UNIX-based host system. Router management RADIUS does not allow users to control which commands can be executed on a router. Following is a summary of the VPDN process when users are authenticated: Step 1 The remote user initiates a PPP connection to the ISP using the analog telephone system or ISDN. Step 2 The ISP NAS accepts the connection. Step 3 The ISP NAS authenticates the end user with CHAP or PAP. The username determines whether the user is a VPDN client. If the user is not a VPDN client, the client accesses the Internet or other contacted service. Step 4 The tunnel endpoints—the NAS and the home gateway—authenticate each other before any sessions are attempted within a tunnel. Step 5 If no L2F tunnel exists between the NAS and the remote user’s home gateway, a tunnel is created. Once the tunnel exists, an unused slot within the tunnel is allocated. Step 6 The home gateway accepts or rejects the connection. Initial setup can include authentication information required to allow the home gateway to authenticate the user. Step 7 The home gateway sets up a virtual interface. Link-level frames can now pass through this virtual interface through the L2F tunnel.
- 286. Foundation Summary 263 Table 5-15 Encryption Methods Encryption Description DES DES is a block cipher algorithm, which means that DES performs operations on fixed-length data streams. DES uses a 56-bit key to encrypt 64-bit datagrams. DES is a published, U.S. Government-approved encryption algorithm. 3DES 3DES is a variant of DES, which iterates (encrypt with one 56-bit key, decrypts with another 56-bit key, and then, finally, encrypts with another 56-bit key) three times with three separate keys. Three keys are used to encrypted data resulting in a 168-bit encryption key. Table 5-16 IKE Phase I/II Phase Components IKE phase I Authenticates IPSec peers Negotiates matching policy to protect IKE exchange Exchanges keys using Diffie-Hellman Establishes IKE security association IKE phase II Negotiates IPSec SA parameters by using an existing IKE SA Establishes IPSec security parameters Periodically renegotiates IPSec SAs to ensure security and that no intruders have discovered sensitive data Can also perform optional additional Diffie-Hellman exchange Table 5-17 IPSec Terminology Attribute Meaning IKE IKE is a protocol that provides utility services for IPSec, such as authentication of peers, negotiation of IPSec SAs, and encryption algorithms. SA A security association is a connection between IPSec peers. MD5 Message Digest version 5, is a hash algorithm that takes an input message (of variable length) and produces a fixed-length output message. IKE uses MD5 for authentication purposes. SHA-1 Secure Hash Algorithm that signs and authenticates data. RSA signatures RSA is a public-key encryption system used for authentication. Users are assigned both private and public keys. The private key is not available to the public and is used to decryption messages created with the public key. continues
- 287. 264 Chapter 5: Security Protocols Table 5-17 IPSec Terminology (Continued) Attribute Meaning CA A certification authority is an entity that provides digital certificates and binds data items within a certificate. AH Authentication header used to authenticated data. AH provides data origin authentication and optional replay-detection services. ESP ESP does not encrypt the original IP header, and only encrypts the IP data by placing a header in between the original IP header and data. ESP provides data confidentiality, data integrity, and data origin authentication DH Diffie-Hellman algorithm. This algorithm is used to initiate and secure the session between two hosts, such as routers. DSS Digital Signature Standard is a mechanism that protects data from an undetected change while traversing the network. DSS verifies the identity of the person sending the data just as when you verify your signature to a bank manager.
- 288. Q&A 265 Q&A The Q & A questions help you assess your readiness for the topics covered on the CCIE Security written exam and those topics presented in this chapter. This format is intended to help you assess your retention of the material. A strong understanding of the answers to these questions will help you on the CCIE Security written exam. You can also look over the questions at the beginning of the chapter again for further review. As an additional study aid, use the CD-ROM provided with this book to take simulated exams, which draw from a database of over 300 multiple-choice questions—all different from those presented in the book. Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.” 1 Define the AAA model and a typical application on a Cisco IOS router. 2 Can you allow a remote user authorization before the user is authenticated with AAA? 3 What IOS command is required when enabling AAA for the first time? 4 What is the privilege level of the following user? Assume AAA is not configured. R2> R2>show priv Current privilege level is 1
- 289. 266 Chapter 5: Security Protocols 5 Define four possible RADIUS responses when authenticating the user through a RADIUS server. 6 What are RADIUS attributes? Supply five common examples. 7 What protocols does RADIUS use when sending messages between the server and client? 8 What predefined destination UDP port number is RADIUS accounting information sent to? 9 What does the following command accomplish on a Cisco IOS router? aaa authentication ppp user-radius if-needed group radius 10 What is the RADIUS server IP address and key for the following configuration? radius-server host 3.3.3.3 radius-server key GuitarsrocKthisplaneT
- 290. Q&A 267 11 TACACS+ is transported over what TCP destination port number? 12 What information is encrypted between a Cisco router and a TACACS+ server? 13 What are the four possible packet types from a TACACS+ server when a user attempts to authenticate a Telnet session to a Cisco router configured for AAA, for example? 14 What is the significance of the sequence number in the TACACS+ frame format? 15 What does the following IOS command accomplish? aaa authentication ppp default if-needed group tacacs+ local 16 What IOS command defines the remote TACACS+ server?
- 291. 268 Chapter 5: Security Protocols 17 What are the major difference between TACACS+ and RADIUS? 18 Kerberos is a third-party authentication protocol operating at what layer of the OSI model? 19 What delivery methods and destination ports does Kerberos support? 20 What does the Kerberos realm define? 21 Applications that have been modified to support Kerberos credential infrastructures are known as what? 22 Define the two steps required in an L2F connection terminating a PPP connection?
- 292. Q&A 269 23 Define the two steps for setting up L2TP for tunneling a PPP connection. 24 What are the steps taken for a VPDN connection between a remote user and a remote LAN? 25 What are the three most common threats from intruders that network administrators face? 26 What does the Digital Signature standard provides 27 What is hash in encryption terminology? 28 Name the two modes of operation in IPSec and their characteristics. 29 What does IKE accomplish?
- 293. 270 Chapter 5: Security Protocols 30 Certificate Enrollment Protocol is transported over what TCP port?
- 294. Scenario 5-1: Configuring Cisco Routers for IPSec 271 Scenario Scenario 5-1: Configuring Cisco Routers for IPSec Figure 5-21 displays a simple two-router topology where traffic from network 131.108.100.0/24 is encrypted when it is sent to the remote network 131.108.200.0/24. Figure 5-21 Scenario Topology Host C 131.108.101.5/24 Ethernet 0/1 Host A 131.108.101.0/24 Host B 131.108.255.0/24 Ethernet 0/0 Ethernet 0/0 131.108.100.1/24 131.108.200.1/24 131.108.100.5/24 IPSec Tunnel 131.108.200.5/24 Example 5-21 displays the working configuration of R1 numbered from 1 to 31. Example 5-21 R1’s Full Configuration 1. version 12.2 2.hostname R1 3.enable password cisco 4.crypto isakmp policy 1 5. hash md5 6. authentication pre-share 7. crypto isakmp key CCIE address 131.108.255.2 8. crypto ipsec transform-set anyname esp-des esp-sha-hmac 9. mode transport 10.crypto map anyname1 1 ipsec-isakmp 11. set peer 131.108.255.2 12. set security-association lifetime seconds 180 13. set transform-set anyname 14. match address 100 15. interface Ethernet0/0 16. ip address 131.108.100.1 255.255.255.0 17. interface Serial0/0 18. ip address 131.108.255.1 255.255.255.252 19. encapsulation frame-relay continues
- 295. 272 Chapter 5: Security Protocols Example 5-21 R1’s Full Configuration (Continued) 20. ip split-horizon 21. ip ospf network point-to-point 22. frame-relay map ip 131.108.255.2 102 broadcast 23. frame-relay interface-dlci 102 24. frame-relay lmi-type ansi 25. crypto map anyname1 26. interface Ethernet0/1 27. ip address 131.108.101.1 255.255.255.0 28. router ospf 1 29. network 131.108.0.0 0.0.255.255 area 0 30. access-list 100 permit ip 131.108.100.0 0.0.0.255 131.108.200.0 0.0.0.255 31. end Example 5-22 displays the working configuration of R2 numbered from 1 through 29. Example 5-22 R2’s Full Configuration 1. Version 12.2 2. hostname R2 3. enable password cisco 4. crypto isakmp policy 1 5. hash md5 6. authentication pre-share 7. crypto isakmp key CCIe address 131.108.255.1 8.crypto ipsec transform-set anyname esp-des esp-sha-hmac 9. mode transport 10. crypto map anyname1 1 ipsec-isakmp 11. set peer 131.108.255.1 12. set security-association lifetime seconds 180 13. set transform-set anyname 14. match address 100 15.interface Ethernet0/0 16.ip address 131.108.200.1 255.255.255.0 17. interface Serial0/0 18. ip address 131.108.255.2 255.255.255.252 19. encapsulation frame-relay 20. ip split-horizon 21. ip ospf network point-to-point 22. frame-relay map ip 131.108.255.1 201 broadcast 23. frame-relay interface-dlci 201 24. frame-relay lmi-type ansi 25. crypto map anyname1 26. router ospf 1 27. network 131.108.0.0 0.0.255.255 area 0 28. access-list 100 permit ip 131.108.200.0 0.0.0.255 131.108.100.0 0.0.0.255 29. end
- 296. Scenario 5-1: Configuring Cisco Routers for IPSec 273 1 The following debug output is seen on R1 after the network administrator pings remote network 131.108.100.1 from Router R2’s console port. Why will the IPSec tunnel not negotiate properly? R2#debug crypto engine Crypto Engine debugging is on R2#ping Protocol [ip]: Target IP address: 131.108.100.1 Repeat count [5]: Datagram size [100]: Timeout in seconds [2]: Extended commands [n]: y Source address or interface: 131.108.200.1 Type of service [0]: Set DF bit in IP header? [no]: Validate reply data? [no]: Data pattern [0xABCD]: Loose, Strict, Record, Timestamp, Verbose[none]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 131.108.100.1, timeout is 2 seconds: 22:58:55: CryptoEngine0: generate alg parameter 22:58:55: CRYPTO_ENGINE: Dh phase 1 status: 0 22:58:55: CRYPTO_ENGINE: Dh phase 1 status: 0 22:58:55: CryptoEngine0: generate alg parameter 22:58:55: CryptoEngine0: create ISAKMP SKEYID for conn id 1 22:58:55: CryptoEngine0: generate hmac context for conn id 1. 22:58:55: %CRYPTO-4-IKMP_BAD_MESSAGE: IKE message from 131.108.255.1 failed it s sanity check or is malformed.... Success rate is 0 percent (0/5) R2# 2 What subnets will be encrypted between Routers R1 and R2? 3 What IOS command produced the following display and from which router? Crypto Map "anyname1" 1 ipsec-isakmp Peer = 131.108.255.2 Extended IP access list 100 access-list 100 permit ip 131.108.100.0 0.0.0.255 131.108.200.0 0.0.0.255 Current peer: 131.108.255.2 Security association lifetime: 4608000 kilobytes/180 seconds PFS (Y/N): N Transform sets={ anyname, } Interfaces using crypto map anyname1: Serial0/0 4 Will Host A be able to communicate with Host B or Host C? The following displays are the IP routing tables on R1 and R2. (Assume the gateway configurations on the PCs are correct.) R1’s IP routing table: R1>show ip route Codes: C - connected, , O - OSPF, 131.108.0.0/16 is variably subnetted, 4 subnets, 2 masks C 131.108.255.0/30 is directly connected, Serial0/0 O 131.108.200.0/24 [110/400] via 131.108.255.2, 00:52:00, Serial0/0 C 131.108.101.0/24 is directly connected, Ethernet0/1 C 131.108.100.0/24 is directly connected, Ethernet0/0
- 297. 274 Chapter 5: Security Protocols R2’s IP routing table: R2>show ip route Codes: C - connected, , O - OSPF 131.108.0.0/16 is variably subnetted, 4 subnets, 2 masks C 131.108.255.0/30 is directly connected, Serial0/0 C 131.108.200.0/24 is directly connected, Ethernet0/0 O 131.108.101.0/24 [110/58] via 131.108.255.1, 00:52:09, Serial0/0 131.108.100.0/24 [110/58] via 131.108.255.1, 00:52:09, Serial0/0 5 To allow the IP subnet 131.108.101.0/24 attached to R1 Ethernet 0/1 interface to be encrypted over the IPSec tunnel and to communicate with the remote PC IP address 131.108.200.5, what configuration changes are required on which router?
- 298. Scenario 5-1 Solutions 275 Scenario Answers Scenario 5-1 Solutions 1 The following debug output advises the network administrator of the problem: 22:58:55: %CRYPTO-4-IKMP_BAD_MESSAGE: IKE message from 131.108.255.1 failed it s sanity check or is malformed.... During the IKE negotiation, the router reports a message that identifies the fault as the share password. R2 is configured with the password, CCIe (should match R1’s pre-shared password set to CCIE). See example 5-21, and code line 7. Changing the IKE password to CCIE with the IOS command, crypto isakmp key CCIE address 131.108.255.1, the following debug output confirms the IPSec connections by pinging from R2 Ethernet 0/0 IP address to R1 Ethernet 0/0 IP address: R2#ping Protocol [ip]: Target IP address: 131.108.100.1 Repeat count [5]: Datagram size [100]: Timeout in seconds [2]: Extended commands [n]: y Source address or interface: 131.108.200.1 Type of service [0]: Set DF bit in IP header? [no]: Validate reply data? [no]: Data pattern [0xABCD]: Loose, Strict, Record, Timestamp, Verbose[none]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 131.108.100.1, timeout is 2 seconds: 23:12:21: CryptoEngine0: generate alg parameter 23:12:21: CRYPTO_ENGINE: Dh phase 1 status: 0 23:12:21: CRYPTO_ENGINE: Dh phase 1 status: 0 23:12:21: CryptoEngine0: generate alg parameter 23:12:21: CryptoEngine0: create ISAKMP SKEYID for conn id 1 23:12:21: CryptoEngine0: generate hmac context for conn id 1 23:12:21: CryptoEngine0: generate hmac context for conn id 1 23:12:21: CryptoEngine0: generate hmac context for conn id 1 23:12:21: CryptoEngine0: clear dh number for conn id 1 23:12:22: CryptoEngine0: generate hmac context for conn id 1 23:12:22: validate proposal 0 23:12:22: validate proposal request 0 23:12:22: CryptoEngine0: generate hmac context for conn id 1.!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 12/13/16 ms R2# The first Ping packet fails because the IPSec tunnel has not yet been created. Then, the IPSec tunnel is successfully brought up between R1 and R2. 2 Access-list 100 on both routers defines the IP subnets that need to be encrypted between R1 and R2. Packets flowing between subnets 131.108.100.0/24 and 131.108.200.0/24 will be encrypted.
- 299. 276 Chapter 5: Security Protocols R1’s ACL is as follows: access-list 100 permit ip 131.108.100.0 0.0.0.255 131.108.200.0 0.0.0.255 R2’s ACL is as follows: access-list 100 permit ip 131.108.200.0 0.0.0.255 131.108.100.0 0.0.0.255 131.108.100.0 3 The show crypto map IOS command displays the remote peer address and the transform set. The previous displays are taken from R1 because the remote peer address is displayed as 131.108.255.2 (R2’s serial 0/0 IP address). 4 Yes, because IPSec has nothing to do with routing IP data, IPSec will encrypt only data as configured. R1 has a remote entry to the network residing on R2 and R2 has a remote entry to the network residing on R1. Here is a sample ping request from R2 to R1 and Host A and Host C: R2>ping 131.108.100.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 131.108.100.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms R2>ping 131.108.101.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 131.108.101.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms R2> R2>ping 131.108.100.5 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 131.108.100.5, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms R2> R2>ping 131.108.101.5 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 131.108.105.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms 5 Because the source network is located on R1, Access-list 100 on R1 needs to be modified, remembering that, by default, an implicit deny is defined on ACL 100. Network 131.108.101.0/24 is only permitted to encrypt traffic to the static ip address 131.108.200.5, hence the ACL line required on R1 becomes the following: access-list 100 permit ip 131.108.100.0 0.0.0.255 131.108.200.0 0.0.0.255 access-list 100 permit ip 131.108.101.0 0.0.0.255 131.108.200.5 0.0.0.0 or: access-list 100 permit ip 131.108.100.0 0.0.0.255 131.108.200.0 0.0.0.255 access-list 100 permit ip 131.108.101.0 0.0.0.255 host 131.108.200.5 On R2 the access-list becomes: access-list 100 permit ip 131.108.200.0 0.0.0.255 131.108.101.0 0.0.0.255 access-list 100 permit ip 131.108.200.0 0.0.0.255 131.108.100.0 0.0.0.255 IP routing is already configured and working. IPSec will ensure only that IP data is encrypted.
- 301. Exam Topics in This Chapter 12 UNIX 13 Windows (NT/95/98/2000) 45 Cisco Secure UNIX 46 Cisco Secure NT 48 Cisco Secure Policy Manager (formerly Cisco Security Manager) 49 Cisco Secure Intrusion Detection System (formerly NetRanger) 50 Cisco Secure Scanner (formerly NetSonar)
- 302. CHAPTER 6 Operating Systems and Cisco Security Applications This chapter reviews two of today’s most common end user applications, UNIX and Windows NT systems. Cisco security applications are also covered. This chapter covers the following topics: • UNIX—The UNIX operating system and some of the most widely used operating commands. The section looks at the files that are manipulated in UNIX to monitor and maintain usernames and passwords. • Microsoft NT Systems—Windows NT 4.0 and some of the concepts used to manage users and domains. • Cisco Secure for Windows and UNIX—Cisco Secure Access Control Server (ACS), the Cisco security application that is available on Windows and UNIX platforms. • NetSonar and NetRanger—Cisco supported applications, NetSonar (Cisco Secure Scanner) and NetRanger (Cisco Secure Intrusion Detection System), to ensure that networks are secured and tested for vulnerabilities. “Do I Know This Already?” Quiz The purpose of this assessment quiz is to help you determine how to spend your limited study time. If you can answer most or all these questions, you might want to skim the “Foundation Topics” section and return to it later, as necessary. Review the “Foundation Summary” section and answer the questions at the end of the chapter to make sure that you have a strong grasp of the material covered. If you intend to read the entire chapter, you do not necessarily need to answer these questions now. If you find these assessment questions difficult, you should read through the entire “Foundation Topics” section and review it until you feel comfortable with your ability to answer all these and the “Q & A” questions at the end of the chapter. Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.”
- 303. 280 Chapter 6: Operating Systems and Cisco Security Applications 1 What UNIX command implements a trace route to the remote network www.guitar.com? a. trace www.guitar.com if DNS is enabled with the IOS command dns server ip-address. b. traceroute www.guitar.com c. trace guitar.com d. UNIX does not support the traceroute command. 2 What UNIX command copies a file? a. copy b. cpy c. cp d. pc 3 A Cisco router network manager wants to copy the configuration in RAM to a UNIX server. What needs to be accomplished before this can occur? a. Issue copy run tftp. b. Modify the .rhosts file. c. Modify the rcmd.allow file. d. Erase the .rhosts.allow file. e. Enable TFTP on the UNIX server. 4 Which of the following is not a UNIX file flag parameter? a. Execute b. Write c. Read d. Read/Write e. Authenticate 5 Which of the following is not a UNIX file type? a. Normal b. Directories c. Special d. Link e. Medium
- 304. “Do I Know This Already?” Quiz 281 6 NetBIOS over TCP/IP operates at what layer of the OSI model? a. 1 b. 2 c. 3 d. 4 e. 5 f. 6 g. 7 7 In Windows NT, what is a domain that is trusted by all remote domains called? a. Local b. Remote c. Single d. Global e. Master f. Slave 8 In Windows NT, what is a domain that is trusted automatically called? a. Local b. Remote c. Single d. Global e. Master f. Slave 9 Which of the following is not an NTFS permission type? a. R b. W c. D d. P e. O f. M
- 305. 282 Chapter 6: Operating Systems and Cisco Security Applications 10 In Windows NT, when in a DOS command window, what command displays the local IP ARP entries? a. arp b. rarp c. rarp –b d. arp –n e. arp –a 11 What devices can the Cisco Secure Policy Manager remotely manage? (Select the best three answers.) a. Routers b. Switches c. NMS workstations d. PIX Firewalls 12 NetRanger LAN interface supports all but which one of the following? a. Ethernet b. Fast Ethernet c. Token Ring d. Serial WAN interfaces e. FDDI 13 Which of the following is not a component of the security wheel? a. Develop b. Secure c. Monitor d. Manage e. Increase 14 Which of the following is false in regards to NetRanger? a. NetRanger examines the IP header. b. NetRanger examines the TCP header. c. NetRanger examines the entire IP frame. d. NetRanger monitors TCP or UDP port scans.
- 306. “Do I Know This Already?” Quiz 283 15 How many phases are completed with NetSonar? a. 1 b. 2 c. 3 d. 4 e. 5 f. 6
- 307. 284 Chapter 6: Operating Systems and Cisco Security Applications Foundation Topics UNIX The UNIX operating system was developed in 1969 at Bell Laboratories. UNIX has continued to develop since its inception. AT&T, for example, released UNIX 4.0. UNIX was designed to be a multiuser system (more than one user can connect to the host at one time), and it is used usually for multiuser systems and networks. Because most engineers are more familiar with DOS (and Windows NT) than UNIX, this section presents some analogies to demonstrate the UNIX command structure. The operating system DOS used in the early days is similar to UNIX in terms of architecture. For example, the command syntax to list the directories in DOS is dir, and in UNIX, it is ls. Table 6-1 displays some of the common commands between UNIX and DOS. Table 6-1 DOS Versus UNIX Commands DOS/Windows NT Command UNIX Command Purpose attrib +h/-h All files starting with a dot (for Either hides (+h) or uncovers (- example .hosts) are hidden h) files from directory lists when automatically. The UNIX the command dir is used. The command mv renames a file. attrib command also displays For example, mv hosts .hosts the file attributes. In UNIX, the . hides the file named hosts. (dot) automatically hides files. cd dirname cd dirname Moves the user to a specific directory. chkdsk Df Checks the disk for logical problems; only admin users can perform this command in UNIX. UNIX commands are case-sensitive. copy/xcopy dirname/filename cp dirname/filename Allows you to copy files. del/erase filename rm filename Erases files from the disk. dir ls Lists the files in the current directory. help command name man command name Displays information about the specified command. rename oldfilename newfilename mv oldfilename newfilename Renames a file. In UNIX, it can also be used to move the file to a different directory.
- 308. UNIX 285 Table 6-1 DOS Versus UNIX Commands (Continued) DOS/Windows NT Command UNIX Command Purpose ping ip-address ping ip-address Pings a local or remote host. tracert traceroute Windows sends ICMP requests with varying time to live (TTL) values. UNIX sends UDP probes, varies the TTL values, and watches for any ICMP messages returned. NOTE The Windows DOS-based attrib command is a widely used command that modifies file attributes. In a Windows environment, the options include the following: C: >help attrib Displays or changes file attributes. ATTRIB [+R | -R] [+A | -A ] [+S | -S] [+H | -H] [[drive:] [path] filename] [/S [/D]] + Sets an attribute. - Clears an attribute. R Read-only file attribute. A Archive file attribute. S System file attribute. H Hidden file attribute. /S Processes matching files in the current folder and all subfolders. /D Processes folders as well The attrib command allows files to be read only, archived, made a system file, or hidden. In UNIX, you use the man command for command syntax help: Simonunixhost% man Usage: man [-M path] [-T macro-package] [ section ] name ... or: man -k keyword ... or: man -f file ... UNIX Command Structure UNIX servers and hosts are managed using files. To manage the files, you need to be aware of the UNIX command structure. A UNIX command contains three basic parts: • Command • Flags • Arguments Figure 6-1 displays the parts of a UNIX command.
- 309. 286 Chapter 6: Operating Systems and Cisco Security Applications Figure 6-1 Three Parts of a UNIX Command Flags cp -i -r oldfile newfile Command Arguments Figure 6-1 displays the copy request command (cp). Notice that most UNIX commands are abbreviations of English words. For example, the copy command is defined by cp. The first part of any UNIX command tells the device to run a specific program or process, such as the copy function. The second part identifies any flags, which directly follow the UNIX process commands; dashes (-) identify flags. The flags in Figure 6-1 are defined as the -i flag, telling the UNIX host to confirm before it overwrites any files in this process, and the -r flag, telling the UNIX host to copy any files in subdirectories if you are copying directories. Finally, the last part is the argument, which, in most cases, is the name of a file or directory. In Figure 6-1, for example, the old filename and the new filename must be specified. Table 6-2 displays some common UNIX commands and their meanings. Table 6-2 Common UNIX Commands Command Description Example cp -i/-r oldfile newfile Makes a copy of a file. You must cp -i simon.doc henry.doc specify the name of the file to be copied and the name of the new file to be created. The -i flag tells the computer to ask before it overwrites any files in this process. The -r flag copies any files in subdirectories if you are copying directories. rm -i/-r filename Erases the specified file. rm -i cisco The -i flag asks you for confirmation before a file is deleted. The -r flag erases directories/ subdirectories and all the files they might contain.
- 310. UNIX 287 Table 6-2 Common UNIX Commands (Continued) Command Description Example rmdir -p directoryname Erases directories. rmdir –ptomII The -p flag allows you to erase a directory and all its contents. Without this flag, the directory must be empty before you erase it. mv -i filename1 filename2 Renames a file. mv 2002ccie 10000ccie The -i flag asks for confirmation before overwriting a file if you attempt to use a filename that is already taken. Without the flag, the original file with the same name is automatically erased. mv -i filename Moves a file to another directory. The mv index.html index1.html directoryname/filename flag serves the same purpose as in the other mv command. man command Displays a description and usage man ls instructions for a specified command. This command is similar to help in a Windows environment. grep -i Allows you to search for a string in grep -i myword *.txt files. The flag –i tells the UNIX server Searches for the keyword to ignore upper- or lowercase. myword in all files that end in .txt. netstat -s Displays a description and usage netstat -s instructions for a specified command. The netstat -s displays statistics for network interfaces and protocols, such as TCP. ifconfig -a Displays the current interfaces that are ifconfig –a configured. Displays the IP address and subnet mask. NOTE All UNIX commands are in lowercase and are case-sensitive. For a free tutorial on UNIX, visit www.ee.surrey.ac.uk/Teaching/Unix/.
- 311. 288 Chapter 6: Operating Systems and Cisco Security Applications UNIX Permissions UNIX allows certain users access to files and commands by setting permissions to ensure that only legitimate users are permitted access to files and directories. To view information about each file, use the -l flag with the UNIX command ls (for example, ls –l). The command ls –s lists the current UNIX permissions. To display both the file permis- sions and file information, combine the flags –s and –l with the command ls (for example, ls –sl or ls –ls). Figure 6-2 displays a sample output for the command ls -ls for a UNIX host named Simon. Figure 6-2 also displays a sample output of the command ls -sl and explains the meaning of this output. Figure 6-2 ls -sl Command Output Permissions Key: r—Read permission. Allows the file to be looked at but not modified. w—Write permission. Allows the file to be modified. x—Search/execute permission. Used for programs or directories. Allows a program to be run or a directory entered and modified. Also can be s. User/Owner Permissions Permissions that have been set for other, which refers to anybody outside of the owner and group -rw-r--r-- 1 echernof2186 Aug 6 20:00 index1.html Permissions for a group of Users - Indicates a file d Indicates a directory l Indicates a link Example Displayed from a UNIX Host Named Simon Simon% ls -sl total 2 0 drwxr-xr-x 2 hbenjami sys 96 Sep 8 1999 Mail 2 -rw------- 1 hbenjami mail 3 Sep 11 17:32 dead.letter
- 312. UNIX 289 When a new file is created in UNIX, the default is to define read and write access to the owner. To set new or modify permissions, use the command chmod flag filename. The chmod flag is always three numbers. The first number affects the owner permissions (U), the second number affects the group permissions (g), and the third number affects the other (o) permissions. Each number can be a number between 0 and 7; Table 6-3 displays the possible values for each flag. Table 6-3 chmod Flag Definitions Number Value 0 No permissions 1 Execute only 2 Write only 3 Write and execute 4 Read only 5 Read and execute 6 Read and write 7 Read, write, and execute NOTE The network administrator is typically given the root password allowing configuration changes, program execution, and file management. For example, to connect a new hard drive, the installation engineer requires the root password. The administrator types in the root password first. After entering the root password, the administrator types the UNIX command mount to attach or detach a file system, also known as the super user. UNIX File Systems UNIX can consist of four main files types: • Normal files—Contain user data • Directories—Containers that hold files • Special files—Input and output devices, such as a disk drive, printer, or CD-ROM • Links—Pointers to another file UNIX stores files and important information in directories. The following are some common examples (might vary according to the UNIX version): • /bin/—Executable system utilities, such as sh, cp, and rm. • /etc/—System configuration files and databases.
- 313. 290 Chapter 6: Operating Systems and Cisco Security Applications • /lib/—Operating system and programming libraries. • /tmp/—System scratch files (all users can write here). • /lost+found/—Where the file system checker puts detached files. • /usr/bin/—Additional user commands. • /usr/include/—Standard system header files. • /usr/lib/—More programming and system call libraries. • /usr/local/—Typically a place where local utilities go. • /usr/man—The manual pages are kept here. NOTE Certain system files created by UNIX store important details about the operational characteristics, such as the password lists for all users. The file named shadow in the /etc directory is a read only, protected file referenced by the program login. The file named passwd contains the passwords for all users. The file named wtmp contains an account of all users that logged into the UNIX host. The file named lastlog contains details of when a user logged out of a UNIX host. The file .rhosts contains information permitting remote devices, such as routers, the capability to TFTP or Remote Copy Protocol (RCP) files to a UNIX host. Microsoft NT Systems This section briefly covers Windows NT 4.0. Cisco Systems requires you to have no more than a conceptual overview on Windows NT systems, so the detail in the next section is only provided to give you the required foundations to pass the CCIE Security written exam. Windows NT allows clients and servers to be grouped into domains or workgroups. A domain is typically a large group of devices under a common administration. A workgroup usually describes a smaller group of Windows devices or any logical collection of computers. A domain is managed by a primary domain controller (PDC), which is a Windows-based server that stores and controls security and user account information for an entire domain. Each domain must have at least one PDC. A backup domain controller (BDC) maintains a copy of the database in the event the PDC is unavailable. NetBEUI was first developed by IBM in the mid 1980s to provide an interface for applications that were currently using Network Basic Input/Output System (NetBIOS).
- 314. Microsoft NT Systems 291 Before routing became popular, NetBEUI was developed as a Layer 2 protocol that allowed devices, such as PCs, to communicate over a broadcast medium, such as Ethernet. NetBEUI was also designed for earlier versions of Windows (Windows 3.1 and MS-DOS-based clients). NetBEUI is not routable and must be bridged when networks are not locally reachable. NetBEUI is still used today. NetBIOS is a session layer protocol that allows communication between PCs in domains or workgroups. NetBIOS provides the following functions: • Authentication • Connection management • Error control • File sharing • Flow control • Full-duplex transmissions • Name resolution • Print sharing • Session management NOTE NetBIOS over IPX is called NWLink, and NetBIOS over TCP/IP is called NetBT. Next, you learn how Windows devices can find network resources by browsing and using Windows name resolution. Browsing and Windows Names Resolution Network Neighborhood, Windows NT’s browsing service, provides end users with a list of all devices available in their network. Before a user’s PC can browse the network or Network Neighborhood, the Windows-based PC must register its name periodically by sending a broadcast to the master browser. The master browser contains a list of all devices available on the network. This service, called browsing, is supported by three methods—NetBEUI, NWLink, and NetBT. In addition to accessing the Network Neighborhood services, Windows devices require name resolution so that network names can be translated to protocol addresses, either IP or IPX.
- 315. 292 Chapter 6: Operating Systems and Cisco Security Applications Networking administrators have four options for name resolution, which are similar to the Domain Name System (DNS) provided by TCP/IP. These four name resolution options for Windows NT network administrators are as follows: • Broadcasts—This method enables end stations to broadcast their names to a designated master browser (typically a Windows NT server). The master browser collects the names of available devices and maintains a list. The list is then sent to all devices that request it. This allows communication between servers and clients. • LMhosts file—This simple method enables local PCs to maintain a static list of all Windows computers available in the network. The file typically contains the name and protocol addresses of all servers available in the domain. For large networks, the file might become too large and unusable, so a service called Windows Internet Naming Services (WINS) was developed (as described in the next entry). • Windows Internet Naming Services (WINS)—This was developed so Windows network administrators could avoid dealing with a large amount of broadcasts or statically defined lists. WINS allows client PCs to dynamically register and request name resolution by a specific server running the WINS services. Instead of sending broadcasts, the client sends unicasts. WINS typically runs on a Windows NT server and has an IP address. Clients are statically or dynamically configured to use the server’s IP address. • Dynamic Host Configuration Protocol (DHCP)—In large networks (which contain thousands of PCs), a static IP address configuration can cause scalability issues because all devices in the network would require file modification. DHCP was developed to dynamically allocate IP addresses and many other parameters, such as subnet masks, gateways, and WINS server addresses. When you use DHCP, a Windows client sends out a broadcast for an IP address, and the DHCP server (a Windows NT server or compatible device) provides all the necessary TCP/IP information. The client then registers its names with the WINS server so browsing can take place. Cisco IOS routers can relay DHCP clients’ requests (because Cisco IOS routers drop broadcast packets by default) with the ip helper-address remote dhcp servers ip address command. NOTE DHCP is an IP address assignment and management solution rather than a name resolution. The DHCP server pushes the WINS/DNS/Gateway addresses to the client making it easier for the client to resolve names. Scaling Issues in Windows NT In larger Windows NT environments, you can have many domains. Windows NT allows information sharing between domains with the use of trusted domains. A trusted domain grants or denies access to clients without having to manage each user individually. Each domain can exchange information and form a trust relationship. Based on these trust relationships, end
- 316. Microsoft NT Systems 293 users from each domain can be allowed or denied access. Creating trust relationships allows secure data to flow between different domains and ensures adequate security for data files and application files in any Windows-based network. Windows NT supports several domain models, including the following: • Single domain—Used in small networks. • Global domain—Automatically trusts every domain. • Master domain—Trusted by all remote domains but does not trust the remote domains. • Multiple master domains—Used in large networks where the master domain is trusted by other master domains, which in turn trust smaller domains. Login and Permissions NT users must log in to the domain. Pressing Control-Alt-Delete together displays the login utility. After a valid username and password pair are entered, the verification process starts by comparing the username/password pair with the data stored in the Security Accounts Manager (SAM), which is stored on the NT server in the form of a database. This database also contains a list of privileges for each user. For example, the database might contain the following permissions: • User_1 is permitted access to group Cisco_Icon. • User_2 is permitted access to group APAC. • Directory d:data has read and write access to both groups Cisco_Icon and APAC. • The Word documents stored in d:dataword are owned by group APAC only. • The Excel documents stored in d:dataexcel are owned by group APAC, and read access is granted to all other users. When a user or client attempts to access objects shared by other users in the domain, permissions are used to authorize or deny services. The Windows NT file system is called New Technology File System (NTFS). NTFS is a naming file system that allows extra security. Earlier versions of Windows, such as 95, did not support NTFS and do not support file permissions. The following are six NTFS permissions: • R—Read only. The data or object can only be viewed. • W—Write access. The data can be changed. • X—Execute. The data can be executed. (For example, a directory can be viewed or a program can be executed.)
- 317. 294 Chapter 6: Operating Systems and Cisco Security Applications • D—Delete. The data can be deleted. • P—Change Permissions. The data access permissions can be altered. • O—Take Ownership. The ownership can be altered. The NTFS permissions can also be combined for certain files and directories. For example, RX (read/execute) allows a client to view and execute the data. NOTE Computers running DOS/Windows 3.X, 95, 98, or ME/Windows NT with FAT partition do not provide any file permissions. They can provide only share-level permission. (Remote users can be permitted or denied access.) File permissions for local users can be implemented only in an NTFS file system. Windows NT Users and Groups The following is an explanation of the groups: • Global Groups—A global group contains only individual user accounts (no groups) from the domain in which it is created. It can be added to a local group. After created, a global group can be assigned permissions and rights, either in its own domain or in any trusting domain. Global groups are available only on Windows NT Server domains. Domain Admins and Domain Users are two built-in groups. • Local Groups—Local groups are created on a Windows NT Server or Workstation computer and are available only on that computer. A local group can contain user accounts or global groups from one or more domains. They cannot contain other local groups. Backup Operator and Guests are examples of built-in local groups. The permissions for a user of multiple groups will be additive of all permissions except for NO PERMISSION, which overrides all other permissions. Windows NT Domain Trust Setting up trust among multiple NT domains allows the users of one domain to use resources from another domain. The trusting domain trusts the trusted domain to manage users, groups, and resources. The trusting domain contains the resources that validated users need to access. Trust relationships aren’t transitive. In other words, if the A domain trusts B, and B trusts C, A doesn’t necessarily trust C. A domain’s administrator must explicitly grant a trust to another domain to establish a trust relationship. Trust is one way; if A trusts B, B does not necessarily trust A.
- 318. Common Windows DOS Commands 295 Common Windows DOS Commands The following are some of the most widely used DOS operating commands in Windows environments along with sample displays: • ipconfig—Displays IP address and subnet mask: C:>ipconfig Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : cisco.com IP Address. . . . . . . . . . . . : 150.100.1.253 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 150.100.1.240 • ipconfig /all—Displays more detailed information about TCP/IP configurations, such as DNS and domain names: C:>ipconfig /all Windows 2000 IP Configuration Host Name . . . . . . . . . . . . : c03298157693425 Primary DNS Suffix . . . . . . . : cisco.com Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : cisco.com Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . cisco.com : Description . . . . . . . . . . . : 3Com 10/100 Mini PCI Ethernet Adaptr Physical Address. . . . . . . . . : 00-00-86-48-7B-35 DHCP Enabled. . . . . . . . . . No . : IP Address. . . . . . . . . . . . : 150.100.1.253 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 150.100.1.240 DNS Servers . . . . . . . . . . . : 64.104.200.116 171.68.10.70 Primary WINS Server . . . . . . . : 64.104.193.200 • arp –a—Displays ARP entries on the local machine: C:>arp -a Interface: 150.100.1.253 on Interface 0x1000003 Internet Address Physical Address Type 150.100.1.240 00-60-09-c4-34-17 dynamic 150.100.1.254 00-b0-64-46-a8-40 dynamic • hostname—Displays the local host name: C:>hostname c03298157693425 • nbtstat—Displays the NetBIOS over TCP/IP statistics. A number of options are displayed: C:>nbtstat Displays protocol statistics and current TCP/IP connections using NBT (NetBIOS over TCP/IP).
- 319. 296 Chapter 6: Operating Systems and Cisco Security Applications NBTSTAT [ [-a RemoteName] [-A IP address] [-c] [-n] [-r] [-R] [-RR] [-s] [-S] [interval] ] -a (adapter status) Lists the remote machine's name table given its name -A (Adapter status) Lists the remote machine's name table given its IP address. -c (cache) Lists NBT's cache of remote [machine] names and their IP addresses -n (names) Lists local NetBIOS names. -r (resolved) Lists names resolved by broadcast and via WINS -R (Reload) Purges and reloads the remote cache name table -S (Sessions) Lists sessions table with the destination IP addresses -s (sessions) Lists sessions table converting destination IP addresses to computer NETBIOS names. -RR (ReleaseRefresh) Sends Name Release packets to WINs and then starts Refresh RemoteName Remote host machine name. IP address Dotted decimal representation of the IP address. interval Redisplays selected statistics, pausing interval seconds between each display. Press Ctrl+C to stop redisplaying statistics. • ping—Provides a means to test and verify remote locations. An example ping to www.cisco.com follows: C:>ping www.cisco.com Pinging www.cisco.com [198.133.219.25] with 32 bytes of data: Reply from 198.133.219.25: bytes=32 time=182ms TTL=248 Reply from 198.133.219.25: bytes=32 time=180ms TTL=248 Reply from 198.133.219.25: bytes=32 time=180ms TTL=248 Reply from 198.133.219.25: bytes=32 time=181ms TTL=248 Ping statistics for 198.133.219.25: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 180ms, Maximum = 182ms, Average = 180ms C:> • tracert—Provides a method to list next hop addresses for remote networks. The following is a sample Windows output when tracert routing to the URL www.smh.com.au: C:>tracert www.smh.com.au Tracing route to smh.com.au [203.26.51.42] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms c6k-bbn1-vlan105.cisco.com [64.105.208.2] 2 <1 ms <1 ms <1 ms c6k-bbn1-msfc-v161.cisco.com [10.66.2.2] 3 <1 ms <1 ms <1 ms sydneycisco-wall-1-f0-1.cisco.com [10.166.128.15] 4 41 ms 236 ms <1 ms telstra-gw.cisco.com [103.141.98.141] 5 1 ms 1 ms <1 ms FastEthernet6-1-0.chw12.Sydney.telstra.net [149.130.85.3] 6 1 ms 1 ms 1 ms FastEthernet1-0-0.ken4.Sydney.telstra.net [203.50.19.14] • route—Provides a method to define static routing entries (Windows NT supports RIP and 2000 supports OSPF). The following example adds a static route for the network 150.100.100.0/24 via the next hop address 131.108.1.1: c:>route add 150.100.100.0 mask 255.255.255.0 131.108.1.1
- 320. Cisco Secure for Windows and UNIX 297 • nslookup—Provides a DNS query for any host names. The following displays the use of nslookup for the host name www.cisco.com: C:>nslookup www.cisco.com Server: dns-sydney.cisco.com Address: 64.104.200.248 Name: www.cisco.com Address: 198.133.219.25 Cisco Secure for Windows and UNIX Cisco Systems has developed a number of scalable security software products to help protect and ensure a secured network in relation to Cisco products. Cisco Secure Access Control Server (ACS), commonly referred to as Cisco Secure, provides additional network security when managing IP networks designed with Cisco devices. Cisco Secure can run on Windows NT/2000 and UNIX platforms. Three versions of Cisco Secure are listed here: • Cisco Secure ACS for NT—This powerful ACS application for NT servers runs both TACACS+ and RADIUS. It can use NT username/password database or Cisco Secure ACS database. • Cisco Secure ACS for UNIX—This powerful ACS application for UNIX includes support for TACACS+ and RADIUS. It supports SQL applications such as Oracle and Sybase. • Cisco Secure Global Roaming Server—This performs TACACS+ and RADIUS proxy functions. It is a standalone server for large ISP networks. NOTE Cisco also has a UNIX-based freeware TACACS+ server available for download. NOTE Cisco Secure topics are tested in the CCIE Security lab exam (particularly Cisco Secure for Windows 2000 server). The written exam does not require you to have a detailed understanding of this application. The main features of Cisco Secure ACS include the following: • Supports centralization of AAA access for all users, including routers and firewalls • Can manage Telnet access to routers and switches
- 321. 298 Chapter 6: Operating Systems and Cisco Security Applications • Can support an unlimited number of network access servers • Supports many different Cisco platforms, including PIX access servers and routers Figure 6-3 displays a typical centralized Cisco Secure ACS performing functions such as user authentication, authorization, and accounting. Figure 6-3 Cisco Secure Example ISDN/PSTN PIX Ethernet Switch Ethernet Switch TACACS+/ TACACS+/ RADIUS RADIUS Cisco Secure NT/UNIX Figure 6-3 displays a typical application where ISDN/PSTN users are authenticated by RADIUS or TACACS+ via the Cisco Secure ACS server. In addition to simultaneous support for RADIUS/TACACS+, Cisco Secure also supports the following AAA features: • TACACS+ support for the following: — Access lists — Privilege level support — Time restrictions where access to network is controlled during the day and night
- 322. Cisco Secure Intrusion Detection System and Cisco Secure Scanner 299 • RADIUS support for the following: — Cisco RADIUS AV pairs — IETF support (RADIUS is a defined standard) • Others include the following: — Support for virtual private networking — The ability to disable accounts after a set number of failed attempts Further description of the Cisco ACS application and screenshots are shown in the sample CCIE Security lab in Chapter 9, “CCIE Security Self-Study Lab.” Cisco Secure Policy Manager Cisco Secure Policy Manager (CSPM) provides a scalable and comprehensive security management system for Cisco Secure PIX Firewalls and Cisco Secure Integrated Systems. Cisco Secure Policy Manager, formerly known as the Cisco Security Manager, is a policy-based security management system for Cisco security technologies and network devices. Policy-based management allows a network administrator to define a set of high-level rules that control the deployment of and access to services, such as FTP and HTTP. CSPM enables the management of remote Cisco Secure PIX and IOS Firewalls. CSPM allows you to configure and edit configurations remotely. CSPM only runs over Microsoft Windows operating systems. NOTE Cisco PIX Firewalls running version 6.2 and above have a built-in, Java-based PIX Device Manager (PDM). PDM allows browser-based management and configuration of PIX Firewalls. Cisco Secure Intrusion Detection System and Cisco Secure Scanner This section covers network security tools that are useful for managing network security. Cisco Secure Intrusion Detection System (IDS), formerly known as NetRanger, and Cisco Secure Scanner, formerly known as NetSonar, are two security applications that allow network monitoring. NOTE The CCIE Security written exam still refers to the terms NetRanger and NetSonar, so this guide refers to NetRanger and NetSonar as well.
- 323. 300 Chapter 6: Operating Systems and Cisco Security Applications NetRanger (Cisco Secure Intrusion Detection System) NetRanger is an enterprise intrusion detection system designed to detect, report, and, in the event of unauthorized access, terminate data sessions between users and host devices. NetRanger is an application designed to detect unauthorized access. Users are not aware that NetRanger is watching data across the network; it is transparent to all systems. NetRanger has two components: • NetRanger Sensor—High-speed device that analyzes the contents of data being trans- ported across a network and determines whether that traffic is authorized or unauthorized. Unauthorized traffic includes ping requests from intruders. Traffic detected from unauth- orized sources is sent directly to the NetRanger Director, and the intruder is removed from the network (optional setting to remove host). • NetRanger Director—Provides real-time response to intruders in the network by blocking access to the network and terminating any active data sessions. The Director collects the real-time information from the Sensor. Figure 6-4 displays the typical network placement of NetRanger products. NetRanger Sensors can be located anywhere in the network. They are typically located close to hosts or entry points to a network, such as dial-in users or Internet connections. Alarms are logged on the Sensor and Director. The alarms are displayed or viewed on the Director. Optional configuration settings include killing an active TCP session or reconfiguring access lists (termed shunning). The sensor can detect the intruder’s IP address and destination ports, and buffer up to 256 characters entered by the illegal devices. NetRanger supports Ethernet (10/100), Token Ring, and FDDI LAN interfaces. NetRanger Sensors can modify predefined access lists on Cisco IOS routers and change the definitions of permitted networks in response to an attack. NetRanger Sensors cannot modify the IP routing table nor reload or shutdown interfaces. When illegal activity is discovered, an alarm is sent directly to configured directors, including multiple directors. The software used on the sensors can be loaded from a central director, allowing easier software upgrades. The GUI interface on the Director also allows network monitoring from one central location, ensuring that one central group within an organization can be directly responsible for monitoring and acting on alarms. GUI interfaces and colored alarms indicate possible vulnerabilities.
- 324. Cisco Secure Intrusion Detection System and Cisco Secure Scanner 301 Figure 6-4 Typical NetRanger Design Sensor Sensor ISDN/PSTN Alarms Alarms Director Director PIX TACACS+/ TACACS+/ RADIUS RADIUS Cisco Secure NT/UNIX The following platforms support NetRanger Sensor applications: • IBM PC Pentium II or higher with the following specifications: — 32 MB RAM — At least 2 GB hard drive — Ethernet, Token Ring, or FDDI — Windows-based software • Ultra Sparc Based UNIX station with the following specifications: — 167 MHz Clone or higher — 64 MB RAM — 2 GB hard drive — Ethernet or FDDI — Solaris version 2.6 or higher software; and HP OpenView installed prior to loading NetRanger software
- 325. 302 Chapter 6: Operating Systems and Cisco Security Applications NetRanger Director can send out an alarm when certain configuration changes are made on Cisco routers, can send e-mail messages when particular alarm levels are reached, and can ensure a TCP attack is thwarted by sending TCP reset segments to unauthorized sources. When a NetRanger Sensor communicates with the Director, if the network is down, up to 255 alternate route paths can be attempted. Packets can be buffered and sent when the network is restored and communications occur (there are no keepalive communications; rather, one device sends and the other waits and listens) to ensure that alarms are sent. The following platforms support NetRanger Director applications: • HP UNIX, Ultra UNIX workstations (not PC-based) • Software: Solaris 2.6, HP UNIX • 128 MB RAM, CD-ROM drive, 4 GB of hard disk space • Example machines include Sun Ultra 170 and HP 725 NOTE NetRanger examines only the IP or TCP header and not actual data. Intruders usually use an attack based on large ICMP traffic, typically fragmented, to discover the behavior of routers in a network. When a router that is set for a particular MTU size receives a fragmented packet, it sends all fragments to the destination, assuming that the end device can reassemble the packet. Intruders typically also use context-based attacks by scanning TCP or UDP ports in use. For more details on how Cisco IOS supports NetRanger, visit www.cisco.com/univercd/cc/td/doc/product/iaabu/csids/csids3/index.htm NetSonar (Cisco Secure Scanner) NetSonar is a Cisco Systems-developed product, now named Cisco Secure Scanner. NetSonar is a software tool designed to investigate vulnerable systems within a network and report the vulnerabilities to the network administrator. NetSonar scans the network to uncover systems that might be vulnerable to security threats by performing a number of predefined steps: • Network mapping—NetSonar compiles an electronic inventory of all host devices on the network. • Security assessment—NetSonar identifies potential security holes by probing and confirming vulnerabilities in the network.
- 326. Cisco Secure Intrusion Detection System and Cisco Secure Scanner 303 • Reports—NetSonar communicates results to the administrator detailing the assessment, such as detailing what operating systems are in use, what the host addresses are, and the associated vulnerabilities. • Network security database—This database lists the critical problems and organizes them by operating system, system services, and device types. Figure 6-5 displays the process completed by NetSonar. Figure 6-5 NetSonar Phase Functions Ping Sweep Network Discovery Phase I/II Port Sweep Potential Problems Rules Analysis Phase III Confirmed Vulnerabilities Vulnerabilities Phase IV Charts Report Data Presentation Phase V/VI Figure 6-5 displays the six phases completed by NetSonar: Phase I—NetSonar sends out ICMP echo requests (pings) to query hosts. Phase II—All live hosts are collected and stored on particular port numbers. Phase III—NetSonar identifies the hardware devices that might be vulnerable, such as routers, switches, firewalls, printers, desktops, and hosts that responded to ping requests. Operating systems and network services are documented and labeled as potential vulnerabilities. Phase IV—Vulnerabilities are confirmed. This phase is intrusive. Phase V—The data is charted for presentation. The data can also be charted graphically as line or 3D bar graphs. Phase VI—The data is reported in a number of different formats, including a summary report, a short and detailed report, or a full technical report.
- 327. 304 Chapter 6: Operating Systems and Cisco Security Applications NetSonar software has the following hardware requirements: • Intel Pentium I or higher • 64 MB RAM • 2 GB hard drive • TCP/IP software or Sun Sparc Solaris with version 2.5 and higher Any HTTP browser can be used to manage the NetSonar server, which can be located anywhere in the IP network. Cisco Systems details more security products at the following URLs: www.cisco.com/en/US/netsol/ns110/ns129/net_solution_home.html www.cisco.com/univercd/cc/td/doc/product/vpn/ciscosec/index.htm Cisco Security Wheel Cisco defines a Security Wheel concept that outlines the critical steps to ensuring that data and networks are secured correctly. The Security Wheel revolves around a strong, well-defined corporate policy. The Security Wheel consists of the following: • Secure—After defining a strong corporate policy, you should secure your network by deploying the products necessary in the appropriate places to achieve your corporate security goals. • Monitor and respond—Continuously monitor using NetRanger tools at strategic points in the network to discover new vulnerabilities. • Test—On a regular and formal basis, test all network components. • Manage and improve—Analyze all the reports and metrics supplied by NetSonar and continue to cycle through the Security Wheel by going through all these steps continuously. Figure 6-6 displays the Cisco Security Wheel graphically. Figure 6-6 Cisco Security Wheel 1) SECURE 4) MANAGE CORPORATE 2) MONITOR and SECURITY and IMPROVE POLICY RESPOND 3) TEST
- 328. Foundation Summary 305 Foundation Summary The Foundation Summary is a condensed collection of material for a convenient review of key concepts in this chapter. If you are already comfortable with the topics in this chapter and decided to skip most of the “Foundation Topics” material, the “Foundation Summary” section can help you recall a few details. If you just read the “Foundation Topics” section, this review should help further solidify some key facts. If you are doing your final preparation before the exam, the “Foundation Summary” section offers a convenient way to do a quick final review. Table 6-4 summarizes important UNIX commands. Table 6-4 UNIX Commands Command Description cp -i/-r oldfile newfile Makes a copy of a file. You must specify the name of the file to be copied and the name of the new file to be created. The -i flag tells the computer to ask before it overwrites any files in this process. The -r flag copies any files in subdirectories if you are copying directories. rm -i/-r filename Erases the specified file. The -i flag asks you for confirmation before a file is deleted. The -r flag erases directories or subdirectories and all the files they contain. rmdir -p directoryname Erases directories. The -p flag allows you to erase a directory and all its contents. Without this flag, the directory must be empty before you can erase it. mv -i filename1 filename2 Renames a file. The -i flag asks for confirmation before overwriting a file if you attempt to use a filename that is already taken. Without the flag, the original file with the same name will be automatically erased. mv -i filename directoryname/ Moves a file to another directory. The flag serves the same filename purpose as in the other mv command. man command Displays a description and usage instructions for a specified command. This command is similar to help in a Windows environment. continues
- 329. 306 Chapter 6: Operating Systems and Cisco Security Applications Table 6-4 UNIX Commands (Continued) Command Description grep -i Allows you to search for a string in files. The flag –i tells the UNIX server to ignore upper- or lowercase. netstat -s Displays a description and usage instructions for a specified command. The netstat -s displays statistics for network interfaces and protocols, such as TCP. ifconfig -a Displays the current interfaces that are configured (displays the IP address and subnet mask). Table 6-5 summarizes the main Windows DOS commands. Table 6-5 DOS Commands Command Meaning ping Provides a means to test and verify remote locations. nslookup Provides a DNS query for any host names. route Provides a method to define static routing entries (Windows NT supports RIP and 2000 supports OSPF). tracert Provides a method to list next hop addresses for remote networks. Table 6-6 Summarizes NetRanger’s two components. Table 6-6 NetRanger Components Component Meaning NetRanger Sensor High-speed device that analyzes the contents of data being transported across a network and determines whether that traffic is authorized or unauthorized. Unauthorized traffic includes ping requests from intruders. NetRanger Director Provides real-time response to intruders in the network by blocking access to the network and terminating any active data sessions. The director collects the real-time information from the sensor. Table 6-7 defines the NetSonar Phase functions. Table 6-7 NetSonar Phase Functions Phase Number Function I Sends ICMP echo requests (ping) to query hosts. II Collects and stores all live hosts on particular port numbers. III Identifies the hardware devices that might be vulnerable, such as routers, switches, firewalls, printers, desktops, and hosts that responded to ping requests.
- 330. Foundation Summary 307 Table 6-7 NetSonar Phase Functions (Continued) Phase Number Function IV Confirms vulnerabilities. This phase is intrusive. V Charts data for presentation. The data can also be charted graphically as line or three-dimensional bar graphs. VI Reports data in a number of different formats, including a summary report, a short and detailed report, or a full technical report. Table 6-8 displays the Cisco Security Wheel model and functions. Table 6-8 Cisco Security Wheel Cisco Security Wheel Meaning Secure After defining a strong corporate policy, you should secure your network by deploying the products necessary in the appropriate places to achieve your corporate security goals. Monitor and respond Continuously monitor using NetRanger tools at strategic points in the network to discover new vulnerabilities. Test On a regular and formal basis, test all network components. Manage and improve Analyze all the reports and metrics supplied by NetSonar and cycle through the Security Wheel by going through all these steps continuously.
- 331. 308 Chapter 6: Operating Systems and Cisco Security Applications Q&A The Q & A questions are designed to help you assess your readiness for the topics covered on the CCIE Security written exam and those topics presented in this chapter. This format is intended to help you assess your retention of the material. A strong understanding of the answers to these questions can help you on the CCIE Security written exam. You can also look over the questions at the beginning of the chapter again for additional review. As an additional study aid, use the CD-ROM provided with this book to take simulated exams, which draw from a database of over 300 multiple-choice questions—all different from those presented in the book. Select the best answer. Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.” 1 What UNIX command displays the files in the current directory? 2 What UNIX command changes a directory from etc/ to bin/? 3 What does the following UNIX command accomplish? cp -i simon.doc henry.doc 4 To define a permission for a UNIX file, what command line interface is required?
- 332. Q&A 309 5 The chmod UNIX command can define what levels of access or permissions on a UNIX host? 6 In a Windows NT environment, what is a domain, primary domain controller, and backup domain controller? 7 What functions does the protocol NetBIOS provide in a Window NT environment? 8 What is the function of the lmhosts file on a Windows platform device? 9 Name and define the six NTFS permission types. 10 In Windows NT 4.0, what DOS command displays any local ARP entries?
- 333. 310 Chapter 6: Operating Systems and Cisco Security Applications 11 Define the terms NetRanger Sensor and Director and their uses? 12 What LAN interfaces can be supported on a NetRanger Sensor? 13 What are the six phases completed by Cisco NetSonar? 14 What is the meaning of the term Security Wheel?
- 334. Scenario 6-2: UNIX File Permissions 311 Scenarios Scenario 6-1: NT File Permissions A group of users in a Windows NT environment are members of the domain CISCO_CCIE. You are supplied the following details regarding file permissions: • PC1 and PC2 are authenticated in domain CISCO. • The CISCO domain is trusted by the CISCO_CCIE domain. • The directory d:data has a file named ccielab35.doc and has access for users in the CISCO domain set to read only access. • A user named hbenjamin in the CISCO domain owns the Word document ccielab3.doc. With these details, can PC1 open and read the file named ccielab35.doc? Scenario 6-2: UNIX File Permissions A newly created program file is on a UNIX server in the etc/bin named simon.exe directory. The root user creates the file simon.exe after compiling some UNIX C-based code. The root user password is set to guitar. How can you allow all users who are authenticated and authorized to view the etc/bin directory access to the file named simon.exe?
- 335. 312 Chapter 6: Operating Systems and Cisco Security Applications Scenario Answers Scenario 6-1 Solution The CISCO domain is part of the large domain CISCO_CCIE. Because the directory d:data is set to read only, users from the CISCO domain are permitted to open the document in read-only mode. User hbenjamin is permitted to open and write to the document because Windows NT sets the privilege for the owner as read/write by default. Scenario 6-2 Solution If the users know the root password, they can enter the root mode by typing root and then the password guitar. This allows the user access. If the root password is not known, the file permissions can be modified with the command chmod 777 simon.exe, and because users can already view the directory etc/bin, access to the file named simon.exe is now permitted.
- 337. Exam Topics in This Chapter 34 Concepts 35 Packet Filtering 36 Proxies 37 Port Address Translation (PAT) 38 Network Address Translation (NAT) 39 Firewalls 40 Active Audit 41 Content Filters 42 Public Key Infrastructure (PKI) 43 Authentication Technologies 44 Virtual Private Networks (VPN) 47 Cisco Secure PIX Firewall 51 IOS Firewall Feature Set
- 338. CHAPTER 7 Security Technologies This chapter covers some of today’s most widely used technologies that enable Network administrators to ensure that sensitive data is secured from unauthorized sources. Cisco’s support for security is also covered, as are all the fundamental foundation topics you will need to master the security CCIE written exam. This chapter covers the following topics: • Advanced security concepts—This section covers some the of the advanced security policies in demilitarized zones (DMZs). • Packet filtering, proxies, NAT, and PAT—This section covers some packet filtering, proxies, and how to hide addresses using Network Address Translation (NAT) and Port Address Translation (PAT). • Cisco Firewall routers and IOS feature set—This section covers the Cisco PIX Firewall and the IOS Firewall feature set available on Cisco routers. • Public Key infrastructure (PKI)—This section covers the Public Key infrastructure (PKI), followed by a description of VPN networks and a typical design example. “Do I Know This Already?” Quiz The purpose of this assessment quiz is to help you determine how to spend your limited study time. If you can answer most or all these questions, you might want to skim the “Foundation Topics” section and return to it later, as necessary. Review the “Foundation Summary” section and answer the questions at the end of the chapter to ensure that you have a strong grasp of the material covered. If you already intend to read the entire chapter, you do not necessarily need to answer these questions now. If you find these assessment questions difficult, read through the entire “Foundation Topics” section and review it until you feel comfortable with your ability to answer all these and the Q & A questions at the end of the chapter.
- 339. 316 Chapter 7: Security Technologies Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.” 1 DMZ stands for what? a. Demilitarized zone b. Demitted zone c. Domain main zone d. Domain name 2 When defining an extended access list, what TCP port numbers can you use? a. Only predefined Cisco keywords b. 0 to –65,000 c. 0 to –65,535 d. 1 to 65,534 e. None of the above 3 When defining an extended access list, what UDP port numbers can you use? a. Only predefined Cisco keywords b. 0 to 65000 c. 0 to 65535 d. 1 to 65534 e. None of the above 4 Which of the following is not a TCP service? a. who b. whois c. finger d. ftp e. pop3 5 Which of the following is not a UDP service? a. BGP b. echo c. domain d. discard e. rip f. snmp
- 340. “Do I Know This Already?” Quiz 317 6 For how many translations does PAT allow you to use one IP address? a. 32,000 b. 64,000 c. 96,000 d. 128,000 e. 256,000 7 PAT translates all private addresses based on what? a. Source port b. Destination port c. Both source and destination d. None 8 NAT is which of the following? a. Network Architectural Language b. National anthem of Latvia c. Network translation d. Network Address Translation 9 NAT is defined in which RFC? a. 1700 b. 1701 c. 2002 d. 1631 e. 1613 10 The following defines which NAT terminology: “A legitimate registered IP address as assigned by the InterNIC?” a. Inside local address b. Outside global address c. Inside global address d. Outside local address
- 341. 318 Chapter 7: Security Technologies 11 What IOS command defines a pool of addresses that will be translated to a registered IP address? a. ip nat inside b. ip nat outside c. ip nat pool d. ip nat inside pool e. ip nat outside pool 12 PIX stands for what? a. Protocol interchange b. Cisco Private Internet c. Private Internet Exchange d. Public Internet Exchange 13 To define how a PIX will route IP data, what is the correct syntax for a PIX 520? a. ip route b. route c. ip route enable d. default-network 14 What is the alias command’s function on a PIX Firewall? a. To define a local host name b. To define the DNS server c. Used in NAT environments where one IP address is translated into another d. Only applicable to Cisco IOS 15 CBAC stands for what? a. CBAC is not a valid term b. Cisco Business architectural centre c. Context-based Access Control d. Context-based Accelerated controller e. Content-based arch. Centre
- 342. “Do I Know This Already?” Quiz 319 16 What is IKE used to accomplish? a. NAT translations b. Ensures that data is not sourced by the right sources c. Ensures that data is not sourced by the wrong sources d. No use e. Both a and c 17 To create a simple VPN tunnel (unencrypted) between two sites, what must you do on a Cisco router? a. Create a GRE tunnel b. Create a routing map c. Nothing, use a PIX d. Create an IPSec tunnel
- 343. 320 Chapter 7: Security Technologies Foundation Topics Advanced Security Concepts A wealth of security concepts have been covered and now some of the techniques used in areas of your network will be covered that are vulnerable to attacks, in particular, the Demilitarized Zone (DMZ). The DMZ is defined as an isolated part of the network that is easily accessible to hosts outside of the network, such as the Internet. Figure 7-1 displays a typical network design where a DMZ is defined with a number of bastion hosts (first line of defense or hosts that can be scarified in case of a network attack or attacks). Figure 7-1 DMZ Design Perimeter or Bastion Hosts – Edge Router FTP Server, HTTP Server, Proxy Servers Internet DMZ Firewalls Private Network Figure 7-1 displays a typical perimeter network where the DMZ is separated by a firewall. Firewalls are network devices such as Private Internet Exchange (PIX), which are discussed later in this chapter. Firewalls are designed to protect the internal (or private) parts of a network from the public domain.
- 344. Advanced Security Concepts 321 The aim of all firewalls is to accomplish the following: • Serve as a traffic point—The traffic from inside and outside the network must pass through the traffic point. • Authorize traffic—Permits only authorized traffic. • Designed to be immune from penetration—Firewalls are designed to be immune from attacks. Firewalls are still often devices that are attacked by outside hosts. • Invisibility—Ensures that the private network is invisible to the outside world. As shown in Figure 7-1, the perimeter router sits between the DMZ and the public domain. Typically, a high performance router or routers will be located here, performing a number of duties including the following: • Ensuring that access to the Internet Protocol (IP) is restricted using access lists • Restricting Transmission Control Protocol (TCP) services • Preventing attacks on firewall systems • Preventing Denial of Service (DoS) attacks on bastion hosts and the private network • Permitting only authorized traffic to the bastion hosts • Logging all network events to external or internal systems • Performing Address translation (NAT/PAT) • Running static or dynamic routing protocols; Cisco PIX is limited to RIP and static routing. NOTE Proxy servers are designed to shield internal devices from outside intruders by replacing the internal hosts’ IP addresses with its own IP address. Most new vendors now allow routers to act as proxy servers. Proxy servers have scalability and speed issues, as all packets must be examined and IP headers modified for packet delivery. Firewalls and perimeter routers have the additional function of packet filtering. A packet filter is a device that inspects all incoming and outgoing packets based on IP source address, desti- nation IP address, and protocol type, such as TCP or UDP. Based on configurable options, the filter decides whether to reject or allow traffic to pass through the device. Table 7-1 summarizes the main functions of a perimeter and firewall router.
- 345. 322 Chapter 7: Security Technologies Table 7-1 Perimeter/Firewall Router Functions Protection Service Method Sniffer or snooping capabilities Control eavesdropping with the TCP/IP service and network layer encryption (IPSec). Control unauthorized access Use authentication, authorization, accounting (AAA), and Cisco Secure. Also, access-list filtering and PIX Firewall. Controlling session replay Control what TCP/IP sessions are authorized. Block SNMP, IP source routing, and finger services to outside hosts. Controlling inbound Filter internal address as the source from the outside world. connections Filter all private addresses. Filter Bootp, Trivial File Transfer Protocol (TFTP), and trace route commands. Allow TCP connections established from the inside network. Permit inbound traffic to DMZ only. Controlling outbound Allow only valid IP addresses to the outside world and filter connections remaining illegal addresses. Packet filtering Use predefined access lists that control the transmission of packets from any given interface, controlling Virtual Terminal lines, VTY, and access, and ensuring that routing updates are authenticated. Cisco IOS routers can filter TCP or UDP protocol types. Example 7-1 displays the number of TCP services you can filter on a Cisco IOS router using extended access lists. Example 7-1 TCP Services Filtered on Cisco IOS Routers R1(config)#access-list 100 permit tcp any any eq ? <0-65535> Port number bgp Border Gateway Protocol (179) chargen Character generator (19) cmd Remote commands (rcmd, 514) daytime Daytime (13) discard Discard (9) domain Domain Name Service (53) echo Echo (7) exec Exec (rsh, 512) finger Finger (79) ftp File Transfer Protocol (21) ftp-data FTP data connections (used infrequently, 20) gopher Gopher (70) hostname NIC hostname server (101) ident Ident Protocol (113) irc Internet Relay Chat (194) klogin Kerberos login (543) kshell Kerberos shell (544)
- 346. Advanced Security Concepts 323 Example 7-1 TCP Services Filtered on Cisco IOS Routers (Continued) login Login (rlogin, 513) lpd Printer service (515) nntp Network News Transport Protocol (119) pim-auto-rp PIM Auto-RP (496) pop2 Post Office Protocol v2 (109) pop3 Post Office Protocol v3 (110) smtp Simple Mail Transport Protocol (25) sunrpc Sun Remote Procedure Call (111) syslog Syslog (514) tacacs TAC Access Control System (49) talk Talk (517) telnet Telnet (23) time Time (37) uucp Unix-to-Unix Copy Program (540) whois Nicname (43) www World Wide Web (HTTP, 80) Example 7-2 displays the extended access list when filtering services based on the UDP protocol suite of services. Example 7-2 UDP Services Filtered on Cisco IOS Routers R1(config)#access-list 101 permit udp any any eq ? <0-65535> Port number biff Biff (mail notification, comsat, 512) bootpc Bootstrap Protocol (BOOTP) client (68) bootps Bootstrap Protocol (BOOTP) server (67) discard Discard (9) dnsix DNSIX security protocol auditing (195) domain Domain Name Service (DNS, 53) echo Echo (7) isakmp Internet Security Association and Key Management Protocol (500) mobile-ip Mobile IP registration (434) nameserver IEN116 name service (obsolete, 42) netbios-dgm NetBios datagram service (138) netbios-ns NetBios name service (137) netbios-ss NetBios session service (139) ntp Network Time Protocol (123) pim-auto-rp PIM Auto-RP (496) rip Routing Information Protocol (router, in.routed, 520) snmp Simple Network Management Protocol (161) snmptrap SNMP Traps (162) sunrpc Sun Remote Procedure Call (111) syslog System Logger (514) tacacs TAC Access Control System (49) talk Talk (517) tftp Trivial File Transfer Protocol (69) time Time (37) who Who service (rwho, 513) xdmcp X Display Manager Control Protocol (177)
- 347. 324 Chapter 7: Security Technologies Examples 7-1 and 7-2 clearly allow a network administrator flexibility when designing perimeter security based on particular port numbers, as defined in RFC 1700. Network Address Translation and Port Address Translation NAT is a router function, which allows it to translate the addresses of hosts behind a firewall. This also helps to overcome IP address shortage. It also provides security by hiding the entire network and their real IP addresses. NAT is typically used for internal IP networks that have unregistered (not globally unique) IP addresses. NAT translates these unregistered addresses into legal addresses on the outside (public) network. PAT provides additional address expansion but is less flexible than NAT. With PAT, one IP address can be used for up to 64,000 hosts by mapping several IP port numbers to one IP address. PAT is secure because the inside hosts’ source IP addresses are hidden from the outside world. The perimeter router typically provides the NAT or PAT function. NAT is defined in RFC 1631, www.ietf.org/rfc/rfc1631.txt. Cisco devices started supporting NAT in IOS versions 11.2 and higher. NAT basically provides the capability to retain your network’s original IP addressing scheme while translating that scheme into a valid Internet IP address to ensure that intruders never view your private address. NOTE IOS 12.0 and higher support full NAT functionality in all images. Version 11.2 and higher need “PLUS” image for a NAT feature set. NAT changes the Layer 3 address when the packet is sent out to the Internet. This is a function no other protocol will do (that is, alter the Layer 3 source address). For your review to fully prepare you for the exam, Table 7-2 explains some of the terminology used in a NAT environment. Table 7-2 NAT Terminology Term Meaning Inside local address An IP address that is assigned to a host on the internal network; that is, the logi- cal address that is not being advertised to the Internet. A local administrator gen- erally assigns this address. This address is NOT a legitimate Internet address. Inside global address A legitimate registered IP address, as assigned by the InterNIC. Outside local The IP address of a network’s outside host that is being translated as it appears address to the inside network. Outside global The IP address assigned to a host on the outside of the network that is being address translated by the host’s owner.
- 348. Network Address Translation and Port Address Translation 325 Figure 7-2 displays a typical scenario where a private address space is deployed that requires Internet access. The Class A 10.0.0.0/8 is not routable in the Internet. Figure 7-2 Typical NAT Scenario Inside or Private Network Outside Network 131.108.1.1/24 10.99.34.0/24 Internet E0 S0 NAT Table InterNic Assigned Address Inside Address Outside Address 210.1.1.0/24 10.99.34.1 192.108.1.1 10.99.34.2 192.108.1.2 ... so on ... and so on The users in Figure 7-2 are configured with the inside local addresses ranging from 10.99.34.1/24 to 10.99.34.254/24. To allow Internet access, NAT (PAT could also be configured if only one IP address was allocated by InterNIC) is configured on Router R1 to permit the inside local addresses access to the Internet. Advantages of using NAT include the following: • You can hide the Class A address space 10.99.34.0/24 To view the NAT translation table on the Cisco router, apply the exec command show ip nat translations on the CLI interface. • It gives you the capability to connect a nonroutable network to the Internet. • You can use unregistered address space and NAT to the Internet. • You can use both NAT/PAT on the same router. • You can have 64,000 inside hosts per allocated IP address. The InterNic is an Internet authority assigned the task of allocating IP address space to the public. In Figure 7-2, assume that the InterNIC assigned the address space 210.1.1.1/24 for use.
- 349. 326 Chapter 7: Security Technologies NOTE Disadvantages of NAT/PAT include the following: • CPU processing power. • Layer 3 header and source address changes. • Voice over IP is not supported yet. • Some Multimedia-intensive applications do not support NAT, especially when the data stream inbound is different from the outbound path (for example, in multicast environments). NAT Operation on Cisco Routers When a packet leaves the inside network, NAT translates the inside address to a unique InterNIC address for use on the outside network, as shown in Figure 7-2. The R1 router in Figure 7-2 will be configured for an address translation and will maintain a NAT table. When an IP packet returns from the outside network, the NAT router will then perform an address translation from the valid InterNIC address to the original local inside address. Dynamic NAT Configuration Task List Look at the steps required to configure Dynamic NAT on a Cisco router. Dynamic NAT maps any unregistered IP addresses to a registered IP address from a group of registered IP addresses. The basic configuration tasks are as follows: 1 Determine the network addresses to be translated. 2 Configure the inside network with the following IOS command: ip nat inside 3 Configure the outside network with the following IOS command: ip nat outside 4 Define a pool of addresses to be translated with the following IOS command: ip nat pool <pool-name> <start ip address> <end ip address> <mask> 5 Define the addresses that are allowed to access the Internet with the following IOS command: ip nat inside source list <access list number> pool <pool name>
- 350. Network Address Translation and Port Address Translation 327 For a more specific illustration, configure NAT on Router R1. In Figure 7-2, the NAT pool name is going to be CCIE. (You can use any name you want.) Assume that the InterNIC has assigned you the Class C address of 210.1.1.0/2424. Your Internet service provider (ISP) has also supplied you the unique address 131.108.1.1/30 to use on your serial connection. Example 7-3 provides a sample NAT configuration for this setup. Example 7-3 Sample NAT Configuration on R1 hostname R1 ip nat pool CCIE 210.1.1.1 210.1.1.254 netmask 255.255.255.0 ip nat inside source 1 pool CCIE interface ethernet0 ip address 10.99.34.1 255.255.255.0 ip nat inside interface serial 0 ip address 131.108.1.1 255.255.255.252 ip address 210.1.1.1 255.255.255.0 secondary ip nat outside access-list 1 permit 10.99.34.0 0.0.0.255 It is assumed that you have an IP routing protocol to advertise the IP networks shown in the sample, which are 131.108.1.0/30 and 210.1.1.0/24, to the remote ISP router through R1’s Serial 0 interface. The configuration shown in Example 7-3 translates the inside addresses 10.99.34.0/24 into globally unique addresses ranging from 210.1.1.1/24 to 210.1.1.254. Monitoring NAT Operations with show Commands To monitor the operation of NAT, you can use the following commands: show ip nat translation [verbose] show ip nat statistics The show ip nat translation command displays the current active transactions. The show ip nat statistics command displays NAT statistics, such as how many translations are currently taking place. There are four different versions of NAT translations: • Static NAT—Maps an unregistered IP address to a registered IP address on a one-to-one basis. This is particularly useful when a device needs to be accessible from outside the network to an internal unregistered address. • Dynamic NAT—Maps an unregistered IP address to a registered IP address from a group of registered IP addresses.
- 351. 328 Chapter 7: Security Technologies • Overloading—A form of dynamic NAT that maps multiple, unregistered IP addresses to a single registered IP address by using different ports. • Overlapping—When the IP addresses used on your internal network are registered IP addresses in use on another network, the router must maintain a lookup table of these addresses so that it can intercept them and replace them with registered unique IP addresses. For more quality examples on NAT, visit the following URL: • www.cisco.com/warp/customer/556/index.shtml • www.cisco.com/warp/customer/707/overload_private.shtml demonstrates when you can NAT over an IPSec tunnel. The following URLs give examples of when you can use NAT over an IPSec tunnel: www.cisco.com/warp/public/556/index.shtml www.cisco.com/warp/public/707/overload_private.shtml NOTE TCP load distribution is typically used in large IP networks that have server farms. You might want to distribute the network load across many servers but advise users to use only one IP address to target. TCP load distribution ensures that all servers are equally loaded. Cisco Private Internet Exchange (PIX) Cisco Private Internet Exchange (PIX) and Cisco IOS feature sets are designed to further enhance a network’s security. The Private Internet Exchange (PIX) Firewall prevents unautho- rized connections between two or more networks. The latest versions of Cisco code for the PIX Firewall also perform many advanced security features, such as AAA services, access lists, VPN Configuration (IPSec), FTP logging, and Cisco IOS-like interface commands. In addition, the PIX Firewall can support multiple outside or perimeter networks in the DMZs. NOTE When reading Cisco documentation about PIX Firewalls, realize that inside networks and outside networks both refer to networks to which the PIX is connected. For example, inside networks are protected by the PIX, but outside networks are considered the “bad guys.” Consider them as trusted and untrusted, respectively. A PIX Firewall permits a connection-based security policy. For example, you might allow Telnet sessions from inside your network to be initiated from within your network but not allow them to be initiated into your network from outside your network.
- 352. Cisco Private Internet Exchange (PIX) 329 The PIX Firewall’s popularity stems from the fact that it is solely dedicated to security. A router is still required to connect to WANs, such as the Internet. Some companies use PIX Firewalls for internal use only where they might have sensitive networks, such as a payroll or human resources department. Figure 7-3 shows a typical network scenario where a PIX Firewall is implemented between an inside network and an outside network. Figure 7-3 PIX Location Cisco IOS Feature Set Enabled Router Internet Outbound No Direct Connections PIX Inbound OK Firewall Connections Router Internet Attached Router Inside Outside Perimeter Protected Servers Server 1 Protected Clients Internet Accessible Server 2 Server BASTION Hosts Although optional, it is recommended that you install the Cisco IOS Firewall software on the router directly connected to the Internet. The Cisco IOS Firewall feature is discussed later in this chapter. Each connection through a PIX Firewall requires memory. You can support up to 32,768 connections with 16 MB of RAM installed on a PIX; 32 MB of memory can support up to 65,536 connections and support up to 260,000 connections with 128 MB.
- 353. 330 Chapter 7: Security Technologies NOTE Demilitarized zones (DMZs) usually exist as part of a network that the Internet community or general public can access, such as a Web, FTP, or SMTP servers. For example, FTP servers allow external users access to public files, such as Cisco IOS Software, which are available online at ftp.cisco.com. Your remaining servers are protected by the firewall. The PIX Firewall logic is engineered around the Adaptive Security Algorithm (ASA). Every inbound packet is checked against the ASA and against connection state information in mem- ory. This stateful approach to security is regarded in the industry as being far more secure than a stateless packet-screening approach. Examples of the stateful approach to security include the following: • No packets can traverse the PIX Firewall without a connection and state. • Outbound connections or states are allowed, except those specifically denied by access control lists. An outbound connection is one where the originator, or client, is on a higher security interface than the receiver, or server. The highest security interface is always the inside interface (value 100), and the lowest is the outside interface (value 0). Any perimeter interfaces can have security levels between the inside and outside values (for example, 50). • Inbound connections or states are denied, except those specifically allowed. An inbound connection or state is one where the originator, or client, is on a lower security interface/ network than the receiver, or server. You can apply multiple exceptions to a single xlate (translation). This lets you permit access from an arbitrary machine, network, or any host on the Internet to the host defined by the xlate. • All Internet Control Message Protocol (ICMP) packets are denied unless specifically permitted. • All attempts to circumvent the previous rules are dropped and a message is sent to syslog. When an outbound packet arrives at a PIX Firewall higher-security-level interface (security levels can be viewed with the show nameif command; by default, the outside interface has a security level set to 100, or untrusted, and the inside interface is set to 0, or trusted), the PIX Firewall checks to see if the packet is valid based on the ASA, and whether or not previous packets have come from that host. If not, the packet is for a new connection, and the PIX Fire- wall creates a translation slot in its state table for the connection. The information that the PIX Firewall stores in the translation slot includes the inside IP address and a globally unique IP address assigned by NAT, PAT, or Identity (which uses the inside address as the outside address). The PIX Firewall then changes the packet’s source IP address to the globally unique address, modifies the checksum and other fields as required, and forwards the packet to the lower-security- level interface. When an inbound packet arrives at an external interface such as the outside interface, it must first pass the PIX Firewall Adaptive Security criteria. If the packet passes the security tests, the PIX Firewall removes the destination IP address, and the internal IP address is inserted in its place. The packet is forwarded to the protected interface.
- 354. Cisco Private Internet Exchange (PIX) 331 NOTE The PIX Firewall supports NAT, which provides a globally unique address for each inside host, and PAT, which shares a single globally unique address for up to 64 K, simultaneously accessing inside hosts. The following is a list of current models that Cisco supports: • PIX 501 • PIX 506/506E • PIX 515/515E • PIX 520 • PIX 525 • PIX 535 For a full feature list of the PIX, visit the following: www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_v51/config/intro.htm#xtocid0 Figure 7-4 displays the PIX 520, which is used in the current CCIE Security lab exam. PIX Firewall devices are based on the Intel Pentium process, which is basically a PC with Cisco- installed PIX software. Figure 7-4 Cisco PIX 520 Rear View Power Switch Standard 1.44 MB Floppy Drive Front View Interfaces are located here. Examples: Inside/outside perimeter/DMZ
- 355. 332 Chapter 7: Security Technologies Configuring a PIX Take a look at configuring the PIX software and the six basic commands used to configure a PIX Firewall. Figure 7-5 Typical PIX Logical Setup Internet Perimeter Router E0 131.108.1.2/24 DMZ PIX Interfaces E0 Outside (Security Level 0) E0 131.108.1.1/24 PIX Firewall E1 PIX Interfaces E1 Inside (Security Level 100) 201.201.201.1 255.255.255.0 Figure 7-5 displays a typical DMZ and perimeter network between the inside (protected) and outside (public) networks. PIX Firewall Configuration Task List The following steps show you how the PIX software is configured for the scenario in Figure 7-5: Step 1 Name the inside and outside interfaces. Step 2 Name interfaces and assign the security levels. (Configuration mode): nameif hardware_id if_name security_level The nameif command lets you assign a name to an interface. You can use this command to assign interface names if you have more than two network interface circuit boards in your PIX Firewall. The first two interfaces have the default names inside and outside. The inside interface has default security level 100, and the outside interface has default security level 0.
- 356. Cisco Private Internet Exchange (PIX) 333 Table 7-3 describes the PIX command nameif as documented on the Cisco documentation CD. Table 7-3 nameif Command and Required Fields Syntax Description hardware_id The hardware name for the network interface that specifies the interface’s slot location on the PIX Firewall motherboard. Interface boards are numbered from the leftmost slot nearest the power supply as slot 0. The internal network interface must be in slot 1. The lowest security_level external interface board is in slot 0, and the next lowest security_level external interface board is in slot 2. Possible choices are Ethernet for Ethernet or Token-ring for Token Ring. The internal interface is ethernet1. These names can be abbreviated with any leading characters in the name; for example, ether1, e2, token0, or t0. if_name A name for the internal or external network interface of up to 48 characters in length. This name can be uppercase or lowercase. By default, the PIX Firewall names the inside interface inside, the outside interface outside, and any perimeter interface intfn, where n is 2 through 5. security_level Either 0 for the outside network or 100 for the inside network. Perimeter interfaces can use any number between 1 and 99. By default, the PIX Firewall sets the security level for the inside interface to security100, and the outside interface to security0. The first perimeter interface is initially set to security10, the second to security15, the third to security20, and the fourth perimeter interface to security25 (a total of 6 interfaces are permitted, with a total of 4 perimeter interfaces permitted). Step 3 Identify the hardware interfaces, speed, and duplex type installed with the following interface command: interface hardware_id [hardware_speed] [shutdown] In Figure 7-5, the following commands are configured: interface ethernet0 10full interface ethernet1 10full Table 7-4 defines and describes the options for the interface command, as documented on the Cisco documentation CD.
- 357. 334 Chapter 7: Security Technologies Table 7-4 interface Command Options Option Description hardware_id Identifies the network interface type. Possible values are ethernet0, ethernet1 to ethernetn, gb-ethernetn, fddi0 or fddi1, token-ring0, and token-ring1 to token- ringn, depending on how many network interfaces are in the firewall. hardware_speed Network interface speed (optional). Do not specify a hardware_speed for a Fiber Distributed Data Interface (FDDI) interface. Possible Ethernet values are as follows: 10baset—Set for 10 Mbps Ethernet half-duplex communication. 10full—Set for 10 Mbps Ethernet full-duplex communication. 100basetx—Set for 100 Mbps Ethernet half-duplex communication. 100full—Set for 100 Mbps Ethernet full-duplex communication. 1000sxfull—Set for 1000 Mbps Gigabit Ethernet full-duplex operation. 1000basesx—Set for 1000 Mbps Gigabit Ethernet half-duplex operation. 1000auto—Set for 1000 Mbps Gigabit Ethernet to auto-negotiate full or half duplex. Aui—Set 10 for Mbps Ethernet half-duplex communication with an AUI cable interface. Auto—Set Ethernet speed automatically. The auto keyword can be used only with the Intel 10/100 automatic speed sensing network interface card, which shipped with the PIX Firewall units manufactured after November 1996. Bnc—Set for 10 Mbps Ethernet half-duplex communication with a BNC cable interface. Possible Token Ring values are as follows: 4mbps—4 Mbps data transfer speed. You can specify this as 4. 16mbps—(Default) 16 Mbps data transfer speed. You can specify this as 16. shutdown Disables an interface. Step 4 Define the inside and outside IP addresses. The ip address if_name ip_address [netmask] command lets you assign an IP address to each interface. Use the show ip command to view which addresses are assigned to the network interfaces. In Figure 7-5, the IP address assignment is defined as follows: ip address inside 201.201.201.1 255.255.255.0 ip address outside 131.108.1.1 255.255.255.0
- 358. Cisco Private Internet Exchange (PIX) 335 Table 7-5 defines the options and meaning of the interface command. Table 7-5 interface Command Option Description if_name The internal or external interface name designated by the nameif command ip_address PIX Firewall unit’s network interface IP address netmask Network mask of ip_address Step 5 Define the NAT with the nat command. The nat command lets you enable or disable address translation for one or more internal addresses. Address translation means that when a host starts an outbound connection, the IP addresses in the internal network are translated into global addresses. NAT lets your network have any IP addressing scheme, and the firewall protects these addresses from visibility on the external network. The command syntax is as follows: nat [(if_name)] nat_id local_ip [netmask [max_conns [em_limit]]] [norandomseq] In Figure 7-5, the following pool is assigned to the PIX: nat (inside) 1 0.0.0.0 0.0.0.0 This command enables all inside hosts to access the Internet. Table 7-6 defines the options of the nat command, as documented on the Cisco documentation CD. Table 7-6 nat Command Options Option Description if_name Any internal network interface name. nat_id The nat_id is an arbitrary positive number between 0 and 2 billion. Specify 0 with IP addresses and netmasks to identify internal networks that desire only outbound identity address translation. Use 0 with the access-list option to specify traffic that should be exempt from NAT. The access list should already be defined, otherwise PIX gives an error message. access-list Associate an access-list command statement to the nat 0 command. local_ip Internal network IP address to be translated. You can use 0.0.0.0 to allow all hosts to start outbound connections. The 0.0.0.0 local_ip can be abbreviated as 0. netmask Network mask for local_ip. You can use 0.0.0.0 to allow all outbound connections to translate using IP addresses from the global pool. continues
- 359. 336 Chapter 7: Security Technologies Table 7-6 nat Command Options (Continued) Option Description max_conns The maximum TCP connections permitted from the interface you specify. em_limit The embryonic connection limit. The default is 0, which means unlimited connections. Set it lower for slower systems and higher for faster systems. Norandomseq Do not randomize the TCP packet’s sequence number. Only use this option if another inline firewall is also randomizing sequence numbers and the result is scrambling the data. Use of this option opens a security hole in the PIX Firewall. Step 6 Define the global pool. The global command defines a pool of global addresses. The global addresses in the pool provide an IP address for each outbound connection, and for those inbound connections resulting from outbound connections. If the nat command is used, you must also use the global command. Basically, when an outbound IP packet is sent from the inside network, the PIX will extract the source address and compare that address to the list of current NAT translations. If there is no entry, a new entry is created. If a NAT translation entry already exists, the packet is forwarded. The PIX syntax for the global command is defined as follows: global [if_name] nat_id global_ip [-global_ip] [netmask global_mask] In Figure 7-5, the pool of address is defined as follows: global (outside) 1 192.192.1.2-192.192.1.30 netmask 255.255.255.224 The pool of addresses is typically assigned to you by the InterNIC or your ISP. Table 7-7 defines the options of the global command, as documented on the Cisco documentation CD. Table 7-7 global Command Options Option Description if_name The external network where you use these global addresses. nat_id A positive number shared with the nat command that groups the nat and global command statements together. The valid ID numbers can be any positive number up to 2,147,483,647. global_ip One or more global IP addresses that the PIX Firewall shares among its connections. If the external network is connected to the Internet, each global IP address must be registered with the Network Information Center (NIC). You can specify a range of IP addresses by separating the addresses with a dash (-).
- 360. Cisco Private Internet Exchange (PIX) 337 Table 7-7 global Command Options (Continued) Option Description global_ip You can create a PAT global command statement by specifying a single IP (Continued) address. You can have one PAT global command statement per interface. A PAT can support up to 65,535 xlate objects. netmask Reserved word that prefaces the network global_mask variable. global_mask The network mask for global_ip. If subnetting is in effect, use the subnet mask; for example, 255.255.255.128. If you specify an address range that overlaps subnets, global will not use the broadcast or network addresses in the pool of global addresses. For example, if you use 255.255.255.224 and an address range of 209.165.201.1 to 209.165.201.30, the 209.165.201.31 broadcast address and the 209.165.201.0 network address will not be included in the pool of global addresses. Step 7 Finally, define how to route IP data with the route command. Use the route command to enter a default or static route for an interface. The PIX syntax is as follows: route if_name ip_address netmask gateway_ip [metric] Configuring Static Routing on a PIX Firewall Figure 7-5 defines all routes via the perimeter router as follows: route outside 0.0.0.0 0.0.0.0 131.108.1.2 Table 7-8 defines the options of the route command, as documented on the Cisco documentation CD. Table 7-8 route Command Options Option Description if_name The internal or external network interface name. ip_address The internal or external network IP address. Use 0.0.0.0 to specify a default route. You can abbreviate the 0.0.0.0 IP address as 0. netmask Specify a network mask to apply to ip_address. Use 0.0.0.0 to specify a default route. The 0.0.0.0 netmask can be abbreviated as 0. gateway_ip Specify the gateway router’s IP address (the next hop-address for this route). metric Specify the number of hops to gateway_ip. In Figure 7-5, this is 1. Example 7-4 displays the full working configuration of the PIX in Figure 7-5. The highlighted portions of this display are configuration commands we have entered, and the nonhighlighted portions are default configurations. One of the advantages of the PIX Firewall, like the Catalysts
- 361. 338 Chapter 7: Security Technologies Ethernet switch, is that you can view the full working and default configuration, unlike Cisco IOS routers where the default configuration is not displayed. Example 7-4 PIX Full Working Configuration pix# write terminal nameif ethernet0 outside security0 nameif ethernet1 inside security100 hostname pixfirewall fixup protocol ftp 21 fixup protocol http 80 fixup protocol smtp 25 fixup protocol h323 1720 fixup protocol rsh 514 fixup protocol sqlnet 1521 names name 1.1.1.1 abcd name 1.1.1.2 a123456789 name 1.1.1.3 a123456789123456 pager lines 24 logging timestamp no logging standby logging console debugging no logging monitor logging buffered debugging no logging trap logging facility 20 logging queue 512 interface ethernet0 10full interface ethernet1 10full mtu outside 1500 mtu inside 1500 ip address inside 201.201.201.1 255.255.255.0 ip address outside 131.108.1.1 255.255.255.0 no failover failover timeout 0:00:00 failover ip address outside 0.0.0.0 failover ip address inside 0.0.0.0 arp timeout 14400 global (outside) 1 192.192.1.2-192.192.1.30 netmask 255.255.255.0 nat (inside) 1 0.0.0.0 0.0.0.0 no rip outside passive no rip outside default no rip inside passive no rip inside default route outside 0.0.0.0 0.0.0.0 131.108.1.2 1 timeout xlate 3:00:00 conn 1:00:00 half-closed 0:10:00 udp 0:02:00 timeout rpc 0:10:00 h323 0:05:00 timeout uauth 0:00:00 absolute no snmp-server location
- 362. Cisco Private Internet Exchange (PIX) 339 Example 7-4 PIX Full Working Configuration (Continued) no snmp-server contact snmp-server community public no snmp-server enable traps telnet timeout 5 terminal width 80 : end Miscellaneous PIX Firewall Commands Three other important commands that are commonly used in PIX configurations are the static, conduit, and alias commands. The static command creates a permanent mapping (Cisco documentation names or calls this a translation slot or xlate) between a local IP address and a global IP address. Use the static and conduit commands when you are accessing an interface of a higher security level from an interface of a lower security level; for example, when accessing the inside from the outside interface. The command syntax is as follows: static [(internal_if_name, external_if_name)] global_ip local_ip [netmask network_mask] [max_conns [em_limit]] [norandomseq] Table 7-9 defines the options of the route command, as documented on the Cisco documentation CD. Table 7-9 route Command Options Option Description internal_if_name The internal network interface name. The higher-security-level interface you are accessing. external_if_name The external network interface name. The lower-security-level interface you are accessing. global_ip A global IP address. This address cannot be a PAT IP address. The IP address on the lower-security-level interface you are accessing. local_ip The local IP address from the inside network. The IP address on the higher- security-level interface you are accessing. netmask Reserve word required before specifying the network mask. network_mask The network mask pertains to both global_ip and local_ip. For host addresses, always use 255.255.255.255. For network addresses, use the appropriate class mask or subnet mask; for example, for Class A networks, use 255.0.0.0. An example subnet mask is 255.255.255.224. continues
- 363. 340 Chapter 7: Security Technologies Table 7-9 route Command Options (Continued) Option Description max_conns The maximum number of connections permitted through the static connection at the same time. em_limit The embryonic connection limit. An embryonic connection is one that has started but not yet completed. Set this limit to prevent attack by a flood of embryonic connections. The default is 0, which means unlimited connections. norandomseq Do not randomize the TCP/IP packet’s sequence number. Use only this option if another inline firewall is also randomizing sequence numbers and the result is scrambling the data. Use of this option opens a security hole in the PIX Firewall. An example of the command is as follows: static (inside,outside) 192.192.1.33 201.201.201.10 The static command should be used in conjunction with either conduit or access-list. A conduit command statement creates an exception to the PIX Firewall Adaptive Security mechanism by permitting connections from one firewall network interface to access hosts on another. The clear conduit command removes all conduit command statements from your configuration. The command syntax is defined as follows: conduit {permit | deny} protocol global_ip global_mask [operator port [port]] foreign_ip foreign_mask [operator port [port]] Table 7-10 displays the options and command syntax for the conduit command, as documented on the Cisco documentation CD. Table 7-10 conduit Command Options Option Description permit Permits access if the conditions are matched. deny Denies access if the conditions are matched. protocol Specifies the transport protocol for the connection. Possible literal values are icmp, tcp, udp, or an integer in the range 0 through 255, representing an IP protocol number. Use ip to specify all transport protocols. global_ip A global IP address previously defined by a global or static command. You can use any if the global_ip and global_mask are 0.0.0.0 0.0.0.0. The any option applies the permit or deny parameters to the global addresses.
- 364. Cisco Private Internet Exchange (PIX) 341 Table 7-10 conduit Command Options (Continued) Option Description global_mask Network mask of global_ip. The global_mask is a 32-bit, four-part dotted decimal, such as 255.255.255.255. Use 0s in a part to indicate bit positions to be ignored. Use subnetting, if required. If you use 0 for global_ip, use 0 for the global_mask; otherwise, enter the global_mask appropriate to global_ip. foreign_ip An external IP address (host or network) that can access the global_ip. You can specify 0.0.0.0 or 0 for any host. If both the foreign_ip and foreign_mask are 0.0.0.0 0.0.0.0, you can use the shorthand any option. foreign_mask Network mask of foreign_ip. The foreign_mask is a 32-bit, four-part dotted decimal, such as 255.255.255.255. Use 0s in a part to indicate bit positions to be ignored. Use subnetting, if required. operator A comparison operand that lets you specify a port or a port range. Use without an operator and port to indicate all ports. For example, conduit permit tcp any any. By default, all ports are denied until explicitly permitted. port Service(s) you permit to be used while accessing global_ip or foreign_ip. Specify services by the port that handles them, such as smtp for port 25, www for port 80, and so on. You can specify ports by either a literal name or a number in the range of 0 to 65535. You can specify all ports by not specifying a port value (for example: conduit deny tcp any any). icmp_type The type of ICMP message. The alias command translates one address into another. The alias command is used when nonregistered addresses have been used in a private network and access is required to the registered address space in the Internet. Consider the following example: the inside network contains the IP subnet address 64.236.16.0/24. Assume this belongs to the website on www.cnn.com. When inside clients try to access www.cnn.com, the packets do not go to the firewall because the client thinks 64.236.16.0/24 is on the local inside network. To correct this, a net alias is created as follows with the alias command: alias (inside) 64.236.16.0 131.108.2.0 255.255.255.0 When the inside network client 64.236.16.0 connects to www.cnn.com, the DNS response from an external DNS server to the internal client’s query would be altered by the PIX Firewall to be 131.108.1.1-254/24.
- 365. 342 Chapter 7: Security Technologies Advanced Cisco PIX Commands Table 7-11 summarizes some of the other useful features on a Cisco PIX Firewall, as documented on the Cisco Documentation CD. Table 7-11 PIX Firewall Advanced Features Command Description ca Configure the PIX Firewall to interoperate with a Certification Authority (CA). clear xlate Clears the contents of the translation slots. show xlate Displays NAT translations. The show xlate command displays the contents of only the translation slots. crypto dynamic-map Create, view, or delete a dynamic crypto map entry. failover [active] Use the failover command without an argument after you connect the optional failover cable between your primary firewall and a secondary firewall. fixup protocol The fixup protocol commands let you view, change, enable, or disable the use of a service or protocol through the PIX Firewall. kill Terminate a Telnet session. Telnet sessions to the PIX must be enabled. telnet ip_address [netmask] [if_name] Specify the internal host for PIX Firewall console access via Telnet from inside hosts only. Cisco PIX Firewall Software Features A list of the current features of the Cisco PIX Firewall product follows: • State-of-the-art Adaptive Security Algorithm (ASA) and stateful inspection firewalling. • Cut-through proxy authenticates and authorizes connections, while enhancing performance. • Easy-to-use web-based interface for managing PIX Firewalls remotely; the web-based interface is not a suggested practice by Cisco for medium to large networks. • Support for up to 10 Ethernet interfaces ranging from 10-BaseT, 10/100 Fast Ethernet to Gigabit Ethernet. • Stateful firewall failover capability with synchronized connection information and product configurations. • True Network Address Translation (NAT), as specified in RFC 1631.
- 366. Cisco Private Internet Exchange (PIX) 343 • Port Address Translation (PAT) further expands a company’s address pool—one IP address supports 64,000 hosts. • Support for IPsec and L2TP/PPTP-based VPNs. • Support for high-performance URL filtering via integration with Websense-based URL filtering solutions. • Mail Guard removes the need for an external mail relay server in perimeter network. • Support for broad range of authentication methods via TACACS+, RADIUS, and Cisco Access Control Server (ACS) integration. • Domain Name System (DNS) Guard transparently protects outbound name and address lookups. • Flood Guard and Fragmentation Guard protect against denial-of-service attacks. • Support for advanced Voice over IP (VoIP) standards. • Java blocking eliminates potentially dangerous Java applets (not compressed or archived), extending authentication, authorization, and accounting capabilities. • Net Aliasing transparently merges overlapping networks with the same IP address space. • Capability to customize protocol port numbers. • Integration with Cisco Intrusion Detection Systems for shunning connections of known malicious IP addresses. • Enhanced customization of syslog messages. • Simple Network Management Protocol (SNMP) and syslog for remote management. • Reliable syslogging using either TCP or UDP. • Extended transparent application support (both with and without NAT enabled) includes the following: — Sun remote procedure call (RPC) — Microsoft Networking client and server communication (NetBIOS over IP) using NAT — Multimedia, including RealNetworks’ RealAudio, Xing Technologies’ Streamworks, White Pines’ CuSeeMe, Vocal Tec’s Internet Phone, VDOnet’s VDOLive, Microsoft’s NetShow, VXtreme Web Theatre 2; and Intel’s Internet Video Phone and Microsoft’s NetMeeting (based on H.323 standards) — Oracle SQL*Net client and server communication Cisco will also publish loopholes found in PIX software, such as the PIX mail guard feature, which was designed to limit SMTP messages but can be exploited by intruders. You can find the Cisco publications at www.cisco.com/warp/public/707/PIXfirewallSMTPfilter-pub.shtml.
- 367. 344 Chapter 7: Security Technologies NOTE When troubleshooting why certain applications, such as SMTP mail or L2TP (TCP 1071) tunnels are not working, a good starting point is always to look at which TCP or UDP ports are filtered by the PIX because, by default, you must configure any TCP/UDP ports you will permit through the PIX with the conduit or static translations commands. Cisco Secure PIX Firewalls, published by Cisco Press (ISBN 1-58705-035-8 by David W. Chapman Jr., Andy Fox), is an excellent resource if you want to learn more about the PIX Firewall. Cisco IOS Firewall Security Feature Set Cisco systems software has developed a version of IOS with security-specific features integrated in current IOS software. It is available only on some Cisco IOS devices. NOTE The need to provide firewall functionally in existing router models led Cisco down a path of enabling IOS to be security aware. Not many folks think of Cisco as a software company but, in fact, they sell more software than hardware. The Cisco IOS features set consists of the following: • Context-based Access Control (CBAC) provides internal users secure, per-application- based access control for all traffic across perimeters, such as between private enterprise networks and the Internet. • Java blocking protects against unidentified, malicious Java applets. • Denial-of-service detection and prevention defends and protects router resources from common attacks, checking packet headers and dropping suspicious packets. • Audit trail details transactions, recording time stamp, source host, destination host, ports, duration, and the total number of bytes transmitted. • Real-time alerts log alerts in case of denial-of-service attacks or other preconfigured conditions. You can use the Cisco IOS Firewall feature set to configure your Cisco IOS router as follows: • An Internet firewall or part of an Internet firewall • A firewall between groups in your internal network • A firewall providing secure connections to or from branch offices • A firewall between your company’s network and your company’s partners’ networks
- 368. Cisco IOS Firewall Security Feature Set 345 For example, when a user authenticates from the Cisco IOS Firewall proxy, authentication is completed by HTTP and access lists are downloaded from AAA server to authorized or rejected connections. The IOS Firewall feature set has many different applications for today’s IP networks. CBAC provides secure, per-application access control across the network. CBAC is designed to enhance security for TCP and UDP applications, and supports protocols such as H.323, RealAudio, and SQL-based applications, to name a few. CBAC can filter TCP/UDP packets based on application layer, transport, and network layer protocol information. Traffic is inspected for sessions that originate on any given interface and also inspect traffic flowing through a firewall. CBAC can inspect FTP, TFTP, or SMTP traffic, but does not inspect ICMP packet flows. CBAC can even manually open and close openings in the firewall to test security in a network. The following list provides samples of protocols supported by CBAC: • Telnet • SNMP • TFTP • SMTP • Finger • Java Blocking • Oracle SQL • RealAudio • H.323 The other major benefits of the Cisco IOS feature set include the following: • Integrated solutions and no need for a PIX Firewall for investments already made in Cisco IOS routers. • No new hardware is required (just a software upgrade). • Allows for full IP routing capabilities. • Cisco customers are already aware of IOS command structure. • Low cost. Cisco IOS Security feature-enabled routers should always maintain the same secure polices described in Chapter 8, “Network Security Policies, Vulnerabilities, and Protection,” such as password encryption and disabling nonessential service, such as Hypertext Transfer Protocol (HTTP) or Dynamic Host Configuration Protocol (DHCP).
- 369. 346 Chapter 7: Security Technologies CBAC Configuration Task List Configuring CBAC requires the following tasks: • Picking an interface: internal or external • Configuring IP access lists at the interface • Configuring global timeouts and thresholds • Defining an inspection rule • Applying the inspection rule to an interface • Configuring logging and audit trail • Other guidelines for configuring a firewall • Verifying CBAC (Optional) Example 7-5 shows a router named R1 with two Ethernet interfaces, one defined as the inside interface (Ethernet0) and one as the outside interface (Ethernet1). For this example, CBAC is being configured to inspect RTSP and H.323 protocol traffic inbound from the protected network on a router with two Ethernet interfaces. Interface Ethernet0 is the protected network, and interface Ethernet1 is the unprotected network. The security policy for the protected site uses access control lists (ACLs) to inspect TCP/UDP protocol traffic. Inbound access for specific protocol traffic is provided through dynamic access lists, which are generated according to CBAC inspection rules. ACL 199 permits TCP and UDP traffic from any source or destination, while denying specific ICMP protocol traffic and permitting ICMP trace route and unreachable messages. The final deny statement is not required but is included for explicitness—the final entry in any ACL is an implicit denial of all IP protocol traffic. Example 7-5 defines the Access-list 199 on Router R1, which has two Ethernet interfaces: Ethernet0 and ethernet1. Example 7-5 Access-list Definition R1(config)# access-list 199 permit tcp any any eq telnet R1(config)# access-list 199 deny udp any any eq syslog R1(config)# access-list 199 deny any any echo-reply R1(config)# access-list 199 deny any any echo R1(config)# access-list 199 deny any any time-exceeded R1(config)# access-list 199 deny any any packet-too-big R1(config)# access-list 199 permit any any traceroute R1(config)# access-list 199 permit any any unreachable R1(config)# access-list 199 permit deny ip any any ACL 199 is applied inbound at interface Ethernet 1 to block all access from the unprotected network to the protected network. Example 7-6 configures the inbound ACL on R1.
- 370. Cisco IOS Firewall Security Feature Set 347 Example 7-6 R1 ACL Inbound Configuration R1(config)#interface ethernet1 R1(config-if)# ip access-group 199 in An inspection rule is created for “users” that covers two protocols: RTSP and H.323. Example 7-7 configures R1 to inspect RTSP and H.323 traffic. Example 7-7 Inspected Traffic R1(config)# ip inspect name users rtsp R1(config)# ip inspect name users h323 The inspection rule is applied inbound at interface Ethernet1 to inspect traffic from users on the protected network. When CBAC detects multimedia traffic from the protected network, CBAC creates dynamic entries in Access-list 199 to allow return traffic for multimedia sessions. Example 7-8 configures the R1 unprotected network to inspect traffic on interface ethernet1. Example 7-8 Inspects Traffic on R1 Protected Interface R1(config)# interface Ethernet1 R1(config-if)# ip inspect users in You can view the CBAC logs by three methods: • Debugging output (refer to the Cisco Documentation CD for full details) • Syslog messages (show logging) • Console messages (system messages) After you complete the inspection of traffic, you can turn off CBAC with the global IOS command no ip inspect. The Cisco Systems IOS feature set also supports AAA, TACACS+, and Kerberos authentication protocols. NOTE Active audit and content filters are used with NetRanger and NetSonar products to allow administrators to decipher or reply to networks when an intruder has accessed the network. CBAC is just another useful tool in IOS that allows a quick audit of an IP network.
- 371. 348 Chapter 7: Security Technologies Public Key Infrastructure In the new digital environment, a Public Key Infrastructure (PKI) ensures that sensitive electronic communications are private and protected from tampering. It provides assurances of the identities of the participants in those transactions, and prevents them from later denying participation in the transaction. PKI provides the following assurances: • Protects privacy by ensuring the data is not read but can’t stop someone from intercepting it (If you can’t read something, what’s the use of that data?) • Assures the integrity of electronic communications by ensuring that they are not altered during transmission • Verifies the identity of the parties involved in an electronic transmission • Ensures that no party involved in an electronic transaction can deny involvement in the transaction Before you send data over the public Internet, you want to make sure that the data, no matter how sensitive, won’t be read by the wrong source. PKI enables data to be sent encrypted by use of a public key, cryptography, and digital signatures. Public key cryptography ensures the confidentiality of sensitive information or messages using a mathematical algorithm, or key, to scramble (encrypt) data, and a related mathematical key to unscramble (decrypt) it. In public key cryptography, authorized users receive special encryption software and a pair of keys, one an accessible public key, and the other a private key, which the user must keep secret. A digital signature (DSS) is an electronic identifier comparable to a traditional, paper-based signature—it is unique and verifiable, and only the signer can initiate it. Before any communication can take place, both parties involved in the data communication must obtain a Certificate of Authority from a Certification Authority (CA), a trusted third party responsible for issuing digital certificates and managing them throughout their lifetime. Consider the following example: a user named Simon wants to communicate with a user named Sharon. Simon already has his digital certificate but Sharon has yet to obtain one. Sharon must identify herself to the CA to obtain a certificate. This is analogous to a passport when you travel the world. When Sharon obtains her digital certificate, it contains a copy of her public key, the certificate’s expiration date, and the CA’s digital signature. Each of these details is public. Sharon also receives a private key, which is not shared with anyone. Now that both parties have a DSS, they can communicate and encrypt data using their public key, but they can decrypt only the data using their respective private keys. Pretty Good Privacy (application layer tool) is an excellent example of this type of communication. I suggest you install the software (free dem- onstration version) and try PKI for yourself. You can find the free software at www.pgp.com.
- 372. Virtual Private Networks 349 Virtual Private Networks A virtual private network (VPN) enables IP traffic to travel securely over a public TCP/IP network by encrypting all traffic from one network to another. A VPN uses “tunneling” to encrypt all information at the IP level. VPN is very loosely defined as a network in which a customer or end user connects to one or more sites through a public infrastructure, such as the Internet or World Wide Web. We have already discussed dialup VPNs or Virtual Private Dialup Network (VPDN) in Chapter 5, “Security Protocols.” VPNs are typically set up permanently between two or more sites. Figure 7-6 displays a typical VPN design. Figure 7-6 VPN Model Private Address Beta Remote Site VPN Tunnels Public Address Space 131.108.1.0/30 Alpha Remote Site Central Site Private Address Internet or Current Service Remote Provider Infrastructure Site Figure 7-6 displays a typical hub (central site) to spoke (remote site) model, where all existing public infrastructure transports data. IP generic routing encapsulation (GRE) tunnels can be set up between the hub and spoke routers, and any protocol can run over the IP tunnel. Consider an example where the router, Alpha, needs to communicate with the remote site, Router Beta. At no time should the private address space be advertised to any public domain. Assuming that IP routing is enabled and configured, we can configure an IP GRE tunnel between Alpha and Beta.
- 373. 350 Chapter 7: Security Technologies Assume that you have a client who wants to create a VPN across your network. The client’s main network is attached via Alpha over the Internet IP cloud. The client has a group of employees in their own IP space on the Ethernet interface. The client has a classless inter- domain routing (CIDR) block of 192.1.64.0/20 for the network attached to the Alpha router, and the CIDR block 141.108.32.0/20 to the network attached to the Beta router. The network 131.108.1.0/30 is assigned between the routers and is pingable. Example 7-9 configures Alpha with a GRE tunnel pointing to the remote IP address 131.108.1.2/30 (Beta’s Serial IP address) and uses 131.108.1.5 for the loopback interface. Example 7-9 Alpha GRE Tunnel hostname Alpha ! interface Loopback0 ip address 131.108.1.1 255.255.255.255 ! IP GRE tunnel configuration follows interface Tunnel0 ip address 192.1.64.1 255.255.255.0 tunnel source Loopback0 tunnel destination 131.108.1.2 ! interface Ethernet0/0 ip address 192.1.65.1 255.255.248.0 ! interface Serial0 Description Link to Beta via Internet Cloud ip address 131.108.1.1 255.255.255.252 ! router ospf 1 network 192.1.64.0.0 0.0.240.255 area 0 End Example 7-10 configures Beta with a GRE tunnel pointing to the remote IP address 131.108.1.1/30 and 131.108.1.6/32 for loopback use. Example 7-10 Beta GRE Tunnel hostname Beta ! interface Loopback0 ip address 131.108.1.2 255.255.255.255 ! IP GRE tunnel configuration follows interface Tunnel0 ip address 192.1.64.2 255.255.255.0 tunnel source Loopback0 tunnel destination 131.108.1.1 ! interface Ethernet0/0
- 374. Virtual Private Networks 351 Example 7-10 Beta GRE Tunnel (Continued) ip address 141.108.32.1 255.255.240.0 ! router ospf 1 network 141.108.0.0 0.0.255.255 area 0 interface Serial0 Description Link to Alapha via Internet Cloud ip address 131.108.1.2 255.255.255.252 ! End The IP GRE tunnel is now configured between the routers Alpha and Beta. While using public address space for the source and destination of the VPN tunnel, the reserved CIDR block 192.1.64.0/20 will not be advertised or routable over the public domain. The private traffic can now flow between both hub site and remote site securely. You can also transport other non-IP protocols over the VPN tunnel, such as Internetwork Packet Exchange (IPX) or AppleTalk. IP GRE tunnels support only IPX or AppleTalk.
- 375. 352 Chapter 7: Security Technologies Foundation Summary The “Foundation Summary” is a condensed collection of material for a convenient review of this chapter’s key concepts. If you are already comfortable with the topics in this chapter and decided to skip most of the “Foundation Topics” material, the “Foundation Summary” will help you recall a few details. If you just read the “Foundation Topics” section, this review should help further solidify some key facts. If you are doing your final preparation before the exam, the “Foundation Summary” offers a convenient way to do a quick final review. Table 7-12 Perimeter or Firewall Router Functions To Protect Method Sniffer or snooping capabilities Control eavesdropping with TCP/IP service and network layer encryption (IPSec). Control unauthorized access Use AAA and Cisco Secure. Also, access-list filtering and PIX Firewall. Controlling session replay Control what TCP/IP sessions are authorized. Block SNMP, IP source routing, and finger services to outside hosts. Controlling inbound Filter the internal address as the source from the outside world. connections Filter all private addresses. Filter Bootp, TFTP, and trace route commands. Allow TCP connections established from the inside network. Permit inbound traffic to DMZs only. Controlling outbound Allow only valid IP addresses to the outside world; filter remaining connections illegal addresses. Packet filtering Use predefined access lists that control the transmission of packets from any given interface, control VTY access, and ensure routing updates are authenticated. Table 7-13 NAT Configuration Steps Step Description 1 Determine the network addresses to be translated. 2 Configure the inside network with the IOS ip nat inside command. 3 Configure the outside network with the IOS ip nat outside command. 4 Define a pool of addresses to be translated with the following IOS command: ip nat pool pool-name start ip address end ip address mask 5 Define the addresses allowed to access the Internet with the following IOS command: ip nat inside source list access list number pool pool name
- 376. Foundation Summary 353 Table 7-14 Cisco PIX Model Numbers PIX 501 PIX 506/506E PIX 515/515E PIX 520 (in current CCIE lab) PIX 525 PIX 535 Table 7-15 PIX Configuration Steps Step Description 1 Name the inside/outside interfaces and security levels. 2 Identify the hardware interfaces and speed/duplex. 3 Define the IP address for inside and outside interfaces. 4 Define NAT/PAT. 5 Define the global pool. 6 Define the IP route path. 7 Define static/conduits or static/access lists (for outside networks to access inside hosts or networks). Table 7-16 PIX Command Options Option Description ca Configures the PIX Firewall to interoperate with a Certification Authority (CA). clear xlate Clears the contents of the translation slots. show xlate Displays NAT translations. The show xlate command displays the contents of only the translation slots. crypto dynamic-map Create, view, or delete a dynamic crypto map entry with this command. failover [active] Use the failover command without an argument after you connect the optional failover cable between your primary firewall and a secondary firewall. fixup protocol The fixup protocol commands let you view, change, enable, or disable the use of a service or protocol through the PIX Firewall. kill Terminate a Telnet session. Telnet sessions to the PIX must be enabled and are sent as clear text. telnet ip_address Specify the internal host for PIX Firewall console access through Telnet. [netmask] [if_name]
- 377. 354 Chapter 7: Security Technologies Table 7-17 Cisco IOS Feature Set Feature Function CBAC Provides internal users secure, per-application-based access control for all traffic across perimeters, such as between private enterprise networks and the Internet. CBAC supports the following: Telnet SMNPSNMP-GDL TFTP SMTP Finger Java Blocking Oracle SQL RealAudio H.323 Java blocking Java blocking protects against unidentified, malicious Java applets. Denial-of-service detection Defends and protects router resources against common attacks, and prevention checking packet headers and dropping suspicious packets. Audit trail Details transactions, recording time stamp, source host, destination host, ports, duration, and total number of bytes transmitted. Real-time alerts Log alerts in case of denial-of-service attacks or other preconfigured conditions (intrusion detection). Firewall An Internet firewall or part of an Internet firewall.
- 378. Q&A 355 Q&A The Q & A questions are designed to help you assess your readiness for the topics covered on the CCIE Security written examination and those topics presented in this chapter. This format helps you assess your retention of the material. A strong understanding of the answers to these questions will help you on the CCIE Security written exam. You can also look over the questions at the beginning of the chapter again for review. As an additional study aid, use the CD-ROM provided with this book to take simulated exams, which draw from a database of over 300 multiple-choice questions—all different from those presented in the book. Select the best answer. Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.” 1 What does the term DMZ refer to? 2 What is the perimeter router’s function in a DMZ? 3 What two main transport layer protocols do extended access lists filter traffic through? 4 Which of the following is not a TCP service? a. Ident b. ftp c. pop3 d. pop2 e. echo
- 379. 356 Chapter 7: Security Technologies 5 Name five UDP services that can be filtered with an extended access-list. 6 What RFC defines NAT? 7 In NAT, what is the inside local address used for? 8 What does the IOS command ip nat inside source list accomplish? 9 What are the four possible NAT translations on a Cisco IOS router? 10 How many connections can be translated with a PIX Firewall for the following RAM configurations: 16 MB, 32MB, or 128MB? 11 When the alias command is applied to a PIX, what does it accomplish?
- 380. Q&A 357 12 What security features does the Cisco IOS Firewall feature set allow a network administrator to accomplish? 13 What does CBAC stand for? 14 Name the eight possible steps to take when configuring CBAC. 15 What is a virtual private network?
- 381. 358 Chapter 7: Security Technologies Scenario Scenario 7-1: Configuring a Cisco PIX for NAT The following configuration is installed on a PIX 520. Users from the inside network 10.0.0.0/8 report to you that they cannot browse the Internet. What is the problem, and what command or commands will rectify the problem? pix# write terminal nameif ethernet0 outside security0 nameif ethernet1 inside security100 hostname pix fixup protocol ftp 21 fixup protocol http 80 fixup protocol smtp 25 fixup protocol h323 1720 fixup protocol rsh 514 fixup protocol sqlnet 1521 logging timestamp no logging standby logging console debugging no logging monitor logging buffered debugging no logging trap logging facility 20 logging queue 512 interface ethernet0 10full interface ethernet1 10full mtu outside 1500 mtu inside 1500 ip address inside 201.201.201.1 255.255.255. ip address outside 131.108.1.1 255.255.255.0 route inside 10.0.0.0 255.0.0.0 201.201.201.2 route outside 0.0.0.0 0.0.0.0 131.018.1.2 no failover failover timeout 0:00:00 failover ip address outside 0.0.0.0 failover ip address inside 0.0.0.0 arp timeout 14400 global (outside) 1 192.192.1.2-192.192.1.30 netmask 255.255.255.224 no rip outside passive no rip outside default no rip inside passive no rip inside default timeout xlate 3:00:00 conn 1:00:00 half-closed 0:10:00 udp 0:02:00 timeout rpc 0:10:00 h323 0:05:00 timeout uauth 0:00:00 absolute no snmp-server location no snmp-server contact snmp-server community public no snmp-server enable traps telnet timeout 5 terminal width 80 : end
- 382. Scenario 7-1 Solution 359 Scenario Answer Scenario 7-1 Solution Cisco PIX Firewalls need to NAT any nonregistered IP address space. In particular, the Class A 10.0.0.0/8 is not routable in the Internet, so you must use NAT to permit access, or you could re-address your entire network, which clearly is not an exercise you will do often. The following command will NAT all inside addresses: nat (inside) 1 0.0.0.0 0.0.0.0 Before you can access the Internet, you must also tell the PIX (remember the PIX is not as intelligent as a router; RIP can be configured by the network administrator), and you must route IP data with the command shown here: route outside 0.0.0.0 0.0.0.0 <default-gateway> This command installs a default route where IP datagrams will be sent, typically, the perimeter router or ISP router.
- 383. Exam Topics in This Chapter 52 Policies 53 Standards Bodies 54 Incident Response Teams 55 Vulnerability Discussions 56 Attacks and Common Exploits 57 Intrusion Detection
- 384. CHAPTER 8 Network Security Policies, Vulnerabilities, and Protection This chapter reviews today’s most common Cisco security policies and mechanisms available to the Internet community to combat cyber attacks. The standard security body, CERT/CC, is covered along with descriptions of Cisco IOS-based security methods that ensure that all attacks are reported and acted upon. Cisco Security applications, such as Intrusion Detection System, are covered to lay the foundations you need to master the topics in the CCIE Security written exam. This chapter covers the following topics: • Network security policies—Standard security policies that should be deployed in any IP network. • Standards bodies and incident response teams—Some of the standard bodies designed to help the Internet community tackle intrusion; the forums and e-mail aliases that can help a network security architect. • Vulnerabilities, Attacks, and Common Exploits—Some of the vulnerabilities and methods that exploit IP networks; some common attacks that exploit data and how that data is retrieved and modified. • Intrusion Detection System (IDS)—How IDS (Cisco IDS strategies, in particular) can be implemented to help deter intruders from gaining access to secure data. • Protecting Cisco IOS from Intrusion—Some of the standard configurations that every IOS-enabled router connected to the Internet should consider to avoid intruders gaining access to unauthorized material. “Do I Know This Already?” Quiz The purpose of this assessment quiz is to help you determine how to spend your limited study time. If you can answer most or all these questions, you might want to skim the “Foundation Topics” section and return to it later, as necessary. Review the “Foundation Summary” section and answer the questions at the end of the chapter to ensure that you have a strong grasp of the material covered. If you intend to read the entire chapter, you do not necessarily need to answer these questions now. If you find these assessment questions difficult, you should read through the entire “Foundation Topics” section and review it until you feel comfortable with your ability to answer all these and the “Q & A” questions at the end of the chapter.
- 385. 362 Chapter 8: Network Security Policies, Vulnerabilities, and Protection Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.” 1 A remote user tries logging into a remote network but fails after three additional tries and is disconnected. What useful information should the network administrator gather? (Select the best two answers.) a. Username b. Invalid password c. Invalid username d. Valid username 2 What is the first step that should be implemented in securing any network? a. Create a database of secure passwords. b. Create the IP address scheme. c. Run NetRanger or NetSonar. d. Define a security policy. e. Configure access lists on all routers. 3 What primary security method can be designed and deployed to secure and protect any IP network after an attack has been documented? a. Security policy b. IP policy c. Countermeasures d. Measurement e. Logging passwords 4 A security administrator notices that a log file stored on a local router has increased in size from 32 k to 64 k in a matter of seconds. What should the network administrator do? a. Increase the buffer to 64 k. b. Decrease the buffer to 16 k. c. Log the event as suspicious and notify the incident response team. d. Nothing, this is normal. e. Both a and b are correct.
- 386. “Do I Know This Already?” Quiz 363 5 What is the primary responsibility of CERT/CC? a. Define access lists for use on routers b. Set security standards c. Coordinate attacks on secure networks d. Maintain a security standard for networks e. Nothing to do with security 6 Who can use network scanners and probes? (Select the best two answers.) a. Intruders b. Security managers c. End users d. Cable service providers 7 What is a bastion host? a. Firewall device supported by Cisco only b. Network’s last line of defense c. Network’s first line of defense d. IP host device designed to route IP packets 8 A TCP SYN attack is what type of attack? a. ICMP b. DoS c. Telnet/Kerberos attack d. Ping attack only 9 When an intruder sends a large amount of ICMP echo (ping) traffic using IP broadcasts, this type of DoS attack is known as what? a. Bastion b. Land.C c. Man in the middle d. Smurf e. Ping of death
- 387. 364 Chapter 8: Network Security Policies, Vulnerabilities, and Protection 10 What kind of attack sends a large ICMP echo request packet with the intent of overflowing the input buffers of the destination machine and causing it to crash? a. Ping of death b. Smurf c. Land.C d. Man in the middle e. Birthday attack 11 In the context of intrusion detection, what is an exploit signature? a. DoS attack b. An attack that is recognized and detected on the network c. The same as a Smurf attack d. The same as a man in the middle attack 12 To stop spam e-mail from overwhelming an e-mail server, what step can you take? a. Ask the ISP for help. b. Nothing, because spam e-mail is too difficult to stop to be worth the effort. c. Install an intrusion detection system that has a signature for spam e-mail. d. Nothing, because the client software takes care of this. e. Change the IOS code. f. Configure the bastion host to stop spam e-mail.
- 388. Network Security Policies 365 Foundation Topics Network Security Policies IP networks are susceptible to unsecured intruders using a number of different methods. Through the campus, by dialup, and through the Internet, an intruder can view IP data and attack vulnerable network devices. IP networks must provide network security for the following reasons: • Inherent technology weaknesses—All network devices and operating systems have inherent vulnerabilities. • Configuration weaknesses—Common configuration mistakes can be exploited to open up weaknesses. • Network policy—The lack of a network policy can lead to vulnerabilities, such as password security. • Outside/inside intruders—Internal and external people always want to exploit network resources and retrieve sensitive data. Every IP network architecture should be based on a sound security policy designed to address all these weaknesses and threats. Every network should have a sound security policy before allowing remote access, for example. Network vulnerabilities must be constantly monitored, found, and addressed because they define points in the network that are potential security weak points (or loopholes) that can be exploited by intruders or hackers. Technologies, such as TCP/IP, which is an open and defined standard, allow intruders to devise programs to send IP packets looking for responses and act on them. Countermeasures can be designed and deployed to secure and protect a network. Intruders are typically individuals who have a broad skill set. Intruders can be skilled in coding programs in Java, UNIX, DOS, C, and C++. Their knowledge of TCP/IP can be exceptional, and they can be very experienced when using the Internet and searching for security loopholes. Sometimes, the biggest security threat comes from within an organization from disgruntled former employees, in particular, who would have access to usernames and passwords. An intruder’s motivation can be based on a number of reasons that make any network a possible target: • Cash profit • Revenge • Vandalism • Cyber terrorism • Challenge to gain prestige or notoriety • Curiosity, to gain experience, or to learn the tools of trade
- 389. 366 Chapter 8: Network Security Policies, Vulnerabilities, and Protection Countermeasures against vulnerabilities attacks ensure that a policy, procedure, or specific technology is implemented so that networks are not exploited. The ever-changing nature of attacks is another major challenge facing network administrators. Intruders today are well organized and trained, and Internet sites are easy targets and offer low risk to intruders. The tools used by intruders (see the section, “Vulnerabilities, Attacks, and Common Exploits,” in this chapter) are increasingly sophisticated, easy to use, and designed for large-scale attacks. Now that you are aware of some of the reasons a network must have a sound security policy and the reason intruders (hackers) want to exploit a poorly designed network, consider some of the standards bodies that are designed to help network administrators. Standards Bodies and Incident Response Teams A number of standards bodies today help a network administrator design a sound security policy. The two main entities that are helpful are the Computer Emergency Response Team Coordination Center (CERT/CC) and the various newsgroups that enable you to share valuable security information with other network administrators. The CERT/CC is a U.S. federally funded research and development center at Carnegie Mellon University in Pittsburgh, Pennsylvania. Following the infamous worm incident (a virus devel- oped to halt IP networks), which brought 10 percent of Internet systems to a halt in November 1988, the CERT/CC has helped to establish incident handling practices that have been adopted by more than 200 response teams around the world. CERT/CC works with the Internet community to facilitate responses to incidents involving the Internet and the hosts that are attacked. CERT/CC is designed to take proactive steps to ensure that future attacks and vulnerabilities are communicated to the entire Internet community. CERT/CC also conducts research aimed at improving the security of existing systems. CERT/CC also helped technology managers with Y2K compliance and various other well- known viruses, such as the Melissa virus. CERT/CC does not focus on the intruders themselves, or on the arrest of individuals responsible for causing havoc; rather, it ensures that vulnerabili- ties and loopholes are closed as soon as possible. CERT/CC does not maintain any security standards (these are left for RFCs); also, it does not provide any protocols to help network administrators. CERT/CC has a number of relationships with other organizations, such as law enforcement, Internet security experts, and the general public, so that any information gathered by the teams involved in stifling attacks is communicated. Examples of intruders actually overcoming network security include the famous Barclay Bank attack in July 2001, where the company’s home page was defaced. The New York Times website was altered in September 1998. In February 2000, Yahoo also came under attack. In response to attacks like these and the increased concern brought about by them, Cisco Systems decided to release a new CCIE Security certification.
- 390. Standards Bodies and Incident Response Teams 367 Cisco Systems also provides a website (for the Cisco Product Security Incident Response Team) where customers can report any security concerns regarding flaws in Cisco IOS products: www.cisco.com/warp/public/707/sec_incident_response.shtml You can also e-mail the Cisco Product Security Incident Response Team directly for emergency issues at securityalert@cisco.com, and for nonemergencies at psirt@cisco.com. NOTE Social engineering is a widely used term that refers to the act of tricking or coercing employees into providing information, such as usernames or mail user identifications and even passwords. First-level phone support personnel are individuals typically called by intruders pretending to work for the company to gain valuable information. In 1998, CERT/CC handled 4942 incidents involving intruders. In 2001, CERT/CC handled over 52,000 incidents resulting is 2437 incidents reports. If you have never heard of CERT/CC, now is the time to read more and ensure that you are alerted to vulnerabilities. For more details on CERT/CC, visit www.cert.org. CERT/CC claims that over 95 percent of intrusions can be stopped with countermeasures in place and monitoring tools. Incident Response Teams Incident response teams are too often set up only after an incident or intrusion occurs. However, sound security administration should already have teams set up to monitor and maintain network security. Incident responses teams do the following: • Verify the incident. • Determine the magnitude of the incident (hosts affected and how many). • Assess the damage (for example, determine if public servers have been modified). • Gather and protect the evidence. After this data has been collected, the incident response team determines whether there is enough trace data to track the intruders. The actual data you discover might be only a small part of the entire puzzle. For example, initially, you might have only a log file or notice that a log file size increased or decreased during the incident. The data should be sent to upper management, to the operations groups within an organization, to all affected sites, and to organizations such as CERT/CC or the press. Organizations like Cisco are typically not going to release a statement to the press detailing any attacks.
- 391. 368 Chapter 8: Network Security Policies, Vulnerabilities, and Protection After the information flows to all parts of an organization, the incident response team restores programs and data from the vendor-supplied media and backup device storage media. The data restored needs to be securely configured (such as routers; see the example in the section, “Protecting Cisco IOS from Intrusion” later in this chapter), including installing all relevant patches for all application-based programs. Finally, the incident response team prepares a report and provides that information to the law enforcement organization if prosecution is required. Internet Newsgroups Another important body for both network administrators and intruders themselves is Internet newsgroups. Newsgroups are mailing list type forums where individuals can share ideas and past incidents to keep current with the latest security concerns and protection policies. As a network administrator, you must be aware of both standards and what intruders are discussing. For example, CERT/CC recommends the following newsgroups: • alt.security—Lists computer security issues as well as other security issues, such as car locks and alarm systems • comp.risks—Moderated forum on the risks to the public in computers and related systems • comp.security.announce—Computer security announcements, including new CERT advisories, summaries, and vendor-initiated bulletins • comp.security.misc—A variety of issues related to computer and network security • comp.security.unix—Security information related to the UNIX operating system • comp.virus—Computer viruses and related topics NOTE The following sites also contain a great wealth of information. Although not security specific, they can help you identify the mechanism used to infiltrate technologies such as TCP/IP: • Internet Domain Survey (www.isc.org/ds/)—Includes Host Count History and pointers to other sources of Internet trend and growth information • Internet Engineering Task Force (IETF) (www.ietf.org/)—Offers technical papers, best practices, standards, and more • Internet Society (ISOC) (www.isoc.org/internet/)—Provides an overview of the Internet, including its history and how it works
- 392. Vulnerabilities, Attacks, and Common Exploits 369 Vulnerabilities, Attacks, and Common Exploits This section covers some of the vulnerabilities in TCP/IP and the tools used to exploit IP networks. TCP/IP is an open standard protocol, which means that both network administrators and intruders are aware of the TCP/IP architecture and vulnerabilities. NOTE There are a number of network vulnerabilities, such as password protection, lack of authentication mechanism, use of unprotected routing protocols, and firewall holes. This section concentrates on TCP/IP vulnerabilities. Network intruders can capture, manipulate, and replay data. Intruders typically try to cause as much damage to a network as possible by using the following methods: • Vandalizing—Accessing the web server and altering web pages. • Manipulating data—Altering the files on a network device. • Masquerading—Manipulating TCP/IP segments to pretend to be at a valid IP address. • Session replay—Capturing, altering, and replaying a sequence of packets to causes unauthorized access. This method identifies weaknesses in authentication. • Session hijacking—Defining himself with a valid IP address after a session has been established to the real IP address by spoofing IP packets and manipulating the sequence number in IP packets. • Rerouting—Routing packets from one source to an intruder source; altering routing updates to send IP packets to an incorrect destination, allowing the intruder to read and use the IP data inappropriately. The following are some of the attacking methods intruders use: • Probes and scans • Denial-of-Service (DoS) attacks (covered in more detail later) • Compromises • Malicious code (such as viruses) As described in Chapter 6, “Operating Systems and Cisco Security Applications,” network scanners and tools are available to both network administrators and intruders. These tools can be used and placed at strategic points in the network to gain access to sensitive data. NetSonar, for example, can be used to find network vulnerabilities and can, therefore, be used by intruders to do as much harm as it does network administrators good if you aren’t aware of these vulnerabilities.
- 393. 370 Chapter 8: Network Security Policies, Vulnerabilities, and Protection DoS attacks are the most common form of attack used by intruders and can take many forms. The intruder’s goal is to ultimately deny access to authorized users and tie up valuable system resources. Figure 8-1 displays several techniques deployed in DoS attacks. Figure 8-1 Forms of Denial of Service Attack Denial of Service (DoS) attacks include -TCP SYN flood attacks -WinNuke -Land.C -Ping of Death -Chargen Attacks Private Network -DNS Poisoning Host or Bastion Hosts R1 Vulnerable Cisco IOS Router Authorized Users Figure 8-1 displays a typical network scenario with a router connected to the Internet and all users have access to hosts in a public domain. A bastion host is a computer or host, such as a UNIX host, that plays a critical role in enforcing any organization’s network security policy. Bastion hosts are typically highly secured (including physically in secure computer rooms), as these hosts are vulnerable to attacks because they are exposed to untrusted or unknown networks and are the first line of defense. Bastion hosts often provide services to Internet users, such as Web services (WWW), and public access systems, such as FTP or SMTP mail. Because these computers are likely to be attacked, they are often referred to as sacrificial hosts.
- 394. Vulnerabilities, Attacks, and Common Exploits 371 The intruder in Figure 8-1 attacks the authorized users and hosts (or bastion host) behind a router by a number of methods, including the following: • Ping of death—Attack that sends an improperly large ICMP echo request packet with the intent of overflowing the input buffers of the destination machine and causing it to crash. The IP protocol header field is set to 1, the last fragment bit is set, and the data length is greater than 65,535, which is greater than the maximum allowable IP packet size. • TCP SYN Flood attacks—This form of DoS attack randomly opens up a number of TCP ports ensuring that network devices are using CPU cycles for bogus requests. By tying up valuable resources on the remote host, the CPU is tied up with bogus requests, and legitimate users experience poor network response or are denied access. This type of attack can make the host unusable. • E-mail attacks—This form of DoS attack sends a random number of e-mails to a host. E-mail attacks try to fill an inbox with bogus e-mails, ensuring that the end user cannot send mail while thousands (or an e-mail bomb) of e-mails are received. • CPU-intensive attacks—This DoS attack ties up systems’ resources by using programs such as TROJAN (a program designed to capture username/passwords from a network), or enabling viruses to disable remote systems. • Teardrop—Exploits an overlapping IP fragment implementation bug in various operating systems. The bug causes the TCP/IP fragmentation reassembly code to improperly handle overlapping IP fragments causing the host to hang or crash. • DNS poisoning—The attacker exploits the DNS server, causing the server to return a false IP address to a domain name query. • UDP Bomb—Sends illegal length field in the packet header, causing Kernel panic and crash. • Distributed Denial Of Service (DDoS)—These DoS attacks are run by multiple hosts. The attacker first compromises vulnerable hosts using various tools and techniques. Then, the actual DOS attack on a target is run from the pool of all the compromised hosts. • Chargen attacks—Establish a User Datagram Protocol (UDP) service by producing a high-character input. This can cause congestion on a network. • Attacks via dialup (out of band)—Applications such as Windows 95 have built-in vulnerabilities on data port 139 (known as WinNuke) if the intruders can ascertain the IP address. • Land.C attacks—A program designed to send TCP SYN packets (TCP SYN is used in the TCP connection phase) that specifies the target’s host address as both source and destination. This program can use TCP port 113 or 139 (source/destination), which can also cause a system to stop functioning.
- 395. 372 Chapter 8: Network Security Policies, Vulnerabilities, and Protection DoS attacks are designed to send traffic to host systems so that they cannot respond to legitimate traffic by overwhelming the end device through a number of incomplete and illegal connections or requests. DoS attacks send more traffic than is possible to process and can send excessive mail requests, excessive UDP packets, and excessive Internet Control Message Protocol (ICMP) pings with very large data packet sizes to render a remote host unusable. Many other known and unknown attacking methods and terms exist. Here are a few more you should be aware of for the written exam: • Spoof attack—The attacker creates IP packets with an address found (or spoofed) from a legitimate source. This attack is powerful in situations where a router is connects to the Internet with one or more internal addresses. The real solution to this form of attack is to track down the source device and stop the attack. • Smurf attack—Named after its exploit program and one of the most recent in the category of network-level attacks against hosts. In this attack, an intruder sends a large amount of ICMP echo (ping) traffic to IP broadcast addresses, which all have a victim’s spoofed source address. For more details, go to www.cert.org/advisories/CA-1998-01.html. Smurf attacks include a primary and secondary victim and are extremely potent damaging to any IP network. Smurf attacks result in a large number of broadcast ICMP networks, and if routers are configured to forward, broadcasts can result in a degraded network and poor performance between the primary and secondary device. A quick solution is to disable IP-directed broadcasts. • Man in the middle attack—Just as with packet sniffers and IP spoofing attacks, a brute- force password attack can provide access to accounts that can be used to modify critical network files and services. An example that compromises your network’s integrity is an attacker modifying your network’s routing tables. By doing so, the attacker ensures that all network packets are routed to him before they are transmitted to their final destination. In such a case, an attacker can monitor all network traffic, effectively becoming a man in the middle. • Birthday attack—Refers to a class of brute-force attacks. It gets its name from the surprising fact that the probability that two or more people in a group of 23 share the same birthday is greater than 50 percent; such a result is called a birthday paradox. Intrusion Detection System Intrusion detection systems (IDS) are designed to detect and thwart network attacks. Based on their location, they can be either of the following: • Network IDS—Examines or sniffs every packet flowing across the network and generates an alarm upon detection of a network attack signature. • Host IDS—Examines operating system information such as logs or system process, against a base line. When the system deviates from the normal values because of an attack, alarms are generated.
- 396. Intrusion Detection System 373 Chapter 6 defines some of the intrusion detection mechanisms you can use in an IP network, namely NetRanger. Cisco IDS delivers a comprehensive, pervasive security solution for combating unauthorized intrusions, malicious Internet worms, and bandwidth and e-Business application attacks. Recently, Cisco announced a number of new products to support IDS: • Cisco IDS Host Sensor 2.5—Bolsters enterprise security by delivering unparalleled levels of protection and customization to customers • Cisco IDS 4250 Appliance Sensor—Raises the performance bar for high-throughput gigabit protection in a performance-upgradable IDS chassis • Cisco IDS 4235 Appliance Sensor—Provides enterprise-class intrusion protection at new price/performance levels • Cisco IDS 3.1 Sensor Software—Delivers powerful web-based, embedded device management, graphical security analysis, and data mining capabilities NOTE In addition to the Cisco IDS 4200 series of IDS appliances, Cisco also has the following IDS sensors: • IOS with IDS feature set for routers • Catalyst 6500 IDS module for switch-based sensor • PIX Firewall with version 6.x with built-in IDS sensor • Cisco IDS Host sensor for Windows, Solaris OS, and web servers, such as IIS and Apache You are not expected to know these details for the written exam; they are presented here for completeness only. Each Cisco IDS sensor can be configured to support a number of different signatures. A Signature Engine is a component of the Cisco IDS sensor designed to support many signatures in a certain category. An engine is composed of a parser and an inspector. Each engine has a set of legal parameters that have allowable ranges or sets of values. Exploit signatures are an identifiable pattern of attack detected by your network device, such as a Cisco IDS Host sensor. Table 8-1 displays the signature lists and descriptions available with Cisco IDS version 3.1. IDS can be used, for example, to detect spam e-mail and still allow regular e-mail. Most ISPs do not detect or remove spam e-mail, so it is up to the security administrator to ensure that spam e-mail is not permitted or used as a DoS attack.
- 397. 374 Chapter 8: Network Security Policies, Vulnerabilities, and Protection Table 8-1 Cisco IDS Signature Engines* Signature Engine Description ATOMIC.ICMP Simple ICMP alarms based on the following parameters: type, code, sequence, and ID ATOMIC.IPOPTIONS Simple alarms based on the decoding of Layer 3 options ATOMIC.L3.IP Simple Layer 3 IP alarms ATOMIC.TCP Simple TCP packet alarms based on the following parameters: port, destination, and flags ATOMIC.UDP Simple UDP packet alarms based on the following parameters: port, direction, and data length FLOOD.HOST.ICMP ICMP floods directed at a single host FLOOD.HOST.UDP UDP floods directed at a single host FLOOD.NET Multiprotocol floods directed at a network segment FLOOD.TCPSYN Connections to multiple ports using TCP SYN SERVICE.DNS.TCP Domain Name Service (DNS) packet analyzer on TCP port 53 (includes compression handler) SERVICE.DNS.UDP UDP-based DNS signatures SERVICE.PORTMAP Remote Procedure Call (RPC) program number sent to port mapper SERVICE.RPC Simple RPC alarms based on the following parameters: program, procedure, and length STATE.HTTP Stateful HTTP protocol decode-based string search (includes anti-evasive URL deobfuscation) STRING.HTTP Specialized STRING.TCP alarms for Web traffic (includes anti-evasive URL deobfuscation) STRING.ICMP Generic ICMP-based string search engine STRING.TCP Generic TCP-based string search engine STRING.UDP Generic UDP-based string search engine SWEEP.HOST.ICMP A single host sweeping a range of nodes using ICMP SWEEP.HOST.TCP A single host sweeping a range of nodes using TCP SWEEP.PORT.TCP TCP connections to multiple destination ports between two nodes SWEEP.PORT.UDP UDP connections to multiple destination ports between two nodes SWEEP.RPC Connections to multiple ports with RPC requests between two nodes * The information in Table 8-1 is from Table 1 at the Cisco web page, www.cisco.com/en/US/partner/products/sw/ secursw/ps2113/prod_technical_reference09186a00800d9dd5.html#56785.
- 398. Protecting Cisco IOS from Intrusion 375 Protecting Cisco IOS from Intrusion Now that you have a snapshot of modern security concerns, this section looks at Cisco IOS and the configuration commands you can use to deny intruders the ability to harm valuable network resources that are typically connected behind a Cisco router. In particular, this section covers how you can stop DoS attacks. Figure 8-2 displays a typical network scenario. You see how to configure the router, separating the public and private networks so that the private network is not vulnerable. Figure 8-2 Typical Internet Connection on R1 Internet Connection WWW Host A Host B .1 131.108.255.0/24 .2 R1 R2 Performs Firewall Function Example 8-1 configures the Router R1 to enable the Nagle algorithm defined in RFC 896. Example 8-1 Enable Nagle service nagle service tcp-keepalives-in service tcp-keepalives-out Cisco Connection Online defines the NAGLE algorithm (www.cisco.com/univercd/cc/td/doc/ product/software/ios100/rpcg/36053.htm): The algorithm developed by John Nagle (RFC 896) helps alleviate the small-packet problem in TCP. In general, it works this way: The first character typed after connection establishment is sent in a single packet, but TCP holds any additional characters typed until the receiver acknowledges the previous packet. Then the second, larger packet is sent, and additional typed characters are saved until the acknowledgment comes back. The effect is to accumulate characters into larger chunks, and pace them out to the network at a rate matching the round-trip time of the given connection. This method is usually effective for all TCP-based traffic. However, do not use the service nagle command if you have X Remote users on X Window system sessions.
- 399. 376 Chapter 8: Network Security Policies, Vulnerabilities, and Protection Enabling this algorithm along with the service tcp keepalive command ensures that no TCP connections on any router get hung. NOTE To generate keepalive packets on idle incoming network connections (initiated by the remote host), use the service tcp-keepalives-in global configuration command. To generate keepalive packets on idle outgoing network connections (initiated by a user), use the service tcp-keepalives-out global configuration command. Example 8-2 configures R1 to disable (on by default) TCP/UDP small servers. Example 8-2 Disable TCP/UDP Small Servers no service udp-small-servers no service tcp-small-servers By default, the TCP servers for Echo, Discard, Chargen, and Daytime services are disabled. When the minor TCP/IP servers are disabled, access to the Echo, Discard, Chargen, and Daytime ports causes the Cisco IOS Software to send a TCP Reset packet to the sender and discard the original incoming packet. When the commands in Example 8-2 are entered, they do not display when you view the configuration because the default is to disable TCP/UDP servers. NOTE When a Cisco IOS router is configured to disable the UDP small servers’ access to Echo, Discard and Chargen ports enable the router to send ICMP port unreachable messages to the source device, and the incoming packet is discarded. It is up to the source station to act on the unreachable ICMP messages. In other words, if this is from an unauthorized host, you will be sending information to the same device. Example 8-3 configures R1 to encrypt all passwords configured on a Cisco router. Example 8-3 Encrypting All Passwords service password-encryption enable secret 5 $1$CNqo$C4bT4/zR.iJF0YEpqMhPF/ enable password 7 13061E010803
- 400. Protecting Cisco IOS from Intrusion 377 This ensures that if anyone (intruder or insider) views the configuration file, the passwords are hidden. Then, define the secret password, because it is hidden using a stronger authentication (md5) than the enable password. Example 8-4 configures R1 to disable DHCP, which is enabled by default. Example 8-4 Disable DHCP no service dhcp Cisco has enabled routers to act as DHCP servers to clients by default. This is not a necessary service to have running, so it should be disabled to stop any intruder from receiving a valid IP address. Example 8-5 enables the Router R1 to log any debug output and define each entry with a timestamp. Example 8-5 Logging Router System Changes and Events service timestamps debug service timestamps log logging buffered 64000 debugging logging rate-limit console 10 except errors no logging console logging trap debugging logging 1.1.1.1 logging 141.108.1.1 logging 5.5.5.5 Make sure the router’s clock is set to the correct time via NTP or manual entry with the clock set command. This allows you to look at the log after any incident has occurred. Also, because you are logging to a remote host or hosts and locally to the buffer, you can disable the debug output to the console port so that messages do not overwhelm the router. You are logging to three different remote hosts. You also buffer and output the log file for viewing at a time favorable to the network administrator. You can enable a Cisco IOS router to log messages with the command, logging on. The command logging buffered enables the router to store logged messages, such as configuration to a local file stored in NVRAM, for later viewing. To view a logging message buffered to memory, use the show logging command. Example 8-6 configures R1 with the service sequence. Example 8-6 Enable Sequence Numbering service sequence-numbers
- 401. 378 Chapter 8: Network Security Policies, Vulnerabilities, and Protection The service category is quite useful. Essentially, enabling it means your syslog entries will be numbered to ensure that they are not tampered with. R1 is configured for TACACS via the remote host 131.108.1.1. Example 8-7 configures R1 for AAA. Example 8-7 AAA Configuration username cisco pass ciSc0 aaa new-model aaa authentication login default group tacacs+ local-case aaa authentication enable default group tacacs+ enable aaa authorization commands 15 default group tacacs+ local aaa accounting exec default stop-only group tacacs+ aaa accounting commands 15 default stop-only group tacacs+ aaa accounting network default stop-only group tacacs+ tacacs-server host 131.108.1.1 tacacs-server key myguitarrocksthisworld Example 8-7 configures R1 for AAA authentication in the event TACACS+ fails to use local authentication with a case-sensitive password to keep hackers guessing. By default, Cisco IOS permits a number of default services. Example 8-8 disables some common services. Example 8-8 Disable Services on by Default no ip http server no ip finger no service pad no ip source-route no ip bootp server Example 8-8 disables R1 for an HTTP server. The finger command service allows remote users to view the output (equivalent to the show users [wide] command). When ip finger is config- ured, the router responds to a telnet a.b.c.d finger command from a remote host by immediately displaying the output of the show users command and then closing the connection. You should turn this service off. The service pad enables all packets to be assembled or disassembled (PAD) between PAD devices and access servers. The command no ip source-route causes the system to discard any IP datagram containing a source-route option. When you disable the BOOTP server, access to the BOOTP ports causes the Cisco IOS Software to send an “ICMP port unreachable” message to the sender and discard the original incoming packet. Example 8-9 enables TCP intercept.
- 402. Protecting Cisco IOS from Intrusion 379 Example 8-9 TCP Intercept ip tcp intercept list 100 ip tcp intercept connection-timeout 60 ip tcp intercept watch-timeout 10 ip tcp intercept one-minute low 1800 ip tcp intercept one-minute high 5000 access-list 100 permit ip any any TCP intercept helps prevent SYN-flooding attacks by intercepting and validating TCP connec- tion requests. In intercept mode, the TCP intercept software intercepts TCP synchronization (SYN) packets from clients to servers that match an extended access list. The router responds; if it is a valid connection, the devices are allowed to communicate. The low and high identifies when TCP intercept should deactivate or activate (TCP aggressive mode). In this case, the IOS command ip tcp intercept one-minute high 5000 defines the number of connection requests (5000) received in the minute before the IOS enters aggressive mode. The IOS command ip tcp intercept one-minute low 1800 defines the number of connection requests (1800) below which the software leaves aggressive mode. Example 8-10 configures R1 to dump the router’s memory contents in case of a router crash. Example 8-10 Allowing Core Dumps ip ftp username rooter ip ftp password $%&#*&^$$%&$ exception core-file secure-r01-core-dump exception protocol ftp exception dump 3.3.3.3 It is important to be able to look at why a router crashed, especially a router that provides a security wall to the outside world. Core dumps can be given to Cisco personnel who can decipher the main reason the router crashed. The IOS command exception core-file secure-r01-core-dump sets the filename generated when the router actually crashes. The IOS command exception protocol ftp defines the protocol used to send the memory dump. The IOS command exception dump 3.3.3.3 defines the remote host where the file will be copied; in this case, the file will be copied via FTP to remote host 3.3.3.3. Cisco Systems TAC engineers will use the memory dump to try and decipher why the router crashed. Example 8-11 shows R1 configured for some common parameters for packets sent to unknown destinations and networks that do not exist.
- 403. 380 Chapter 8: Network Security Policies, Vulnerabilities, and Protection Example 8-11 IP Unreachables and Routes to Null0 interface loopback0 ip address 3.3.3.3 255.255.255.255 no ip redirects no ip unreachables interface null0 no ip unreachables ip route 131.0.0.0 255.0.0.0 null0 The IOS command no ip redirects disables the Cisco router from sending ICMP redirect messages to a device’s source from the same interface. The IOS command no ip unreachables disables the router from sending ICMP unreachables for packets it is not configured for. The ip route command ensures that packets received for the network 131.0.0.0/8 are thrown away and not acted on. This can stop a routing loop and an intruder trying to spoof (pretending) to belong to network 131.0.0.0/8. Loopback interfaces are the source of log messages. Loopbacks are often used for routing protocols, as well, because a logical interface does not go down and is reliable. Assign an IP address that uniquely identifies this router. Then, configure and activate the null0 interface as a place to send unknown destination packets. This becomes the trap for packets; they can route in but they can’t route out in case an intruder is spoofing networks from valid IP networks. The configurations shown in Examples 8-1 through 8-11 are just some of the techniques you can use to ensure vulnerable routers are secure. Just imagine all the routers in the Internet that do not contain this level of security, and you will be aware of the challenges faced in the day- to-day running of the WWW and reasons why organizations like CERT/CC are an invaluable resource. For more details on security configurations visit www.cisco.com/warp/public/707/index.shtml.
- 404. Foundation Summary 381 Foundation Summary The Foundation Summary is a condensed collection of material for a convenient review of key concepts in this chapter. If you are already comfortable with the topics in this chapter and decided to skip most of the Foundation Topics material, the “Foundation Summary” section can help you recall a few details. If you just read the “Foundation Topics” section, this review should help further solidify some key facts. If you are doing your final preparation before the exam, the “Foundation Summary” section offers a convenient way to do a quick final review. Table 8-2 summarizes the key reasons that networks should be secured. Table 8-2 Security Policies Policy Reason Meaning Inherent technology All network devices and operating systems have inherent weaknesses vulnerabilities. Configuration weaknesses Common configurations mistakes can be exploited to open weaknesses. Network policy vulnerabilities The lack of network policies can lead to vulnerabilities such as password security. Outside/inside intruders There are always internal and external people wanting to exploit network resources and retrieve sensitive data. Table 8-3 summarizes the key motivation factors behind intruders attacking secure and unsecured networks. Table 8-3 Intruder/Hackers Motivations Intruder/Hackers Motivation Explanation Cash profit To make money from attacks, such as by transferring funds Revenge To get back at employers or individuals Vandalism To cause damage for personal satisfaction Cyber terrorism To gain an advantage or notoriety for an organization’s ideology For a challenge Peer pressure or challenges set by other hackers to gain notoriety Curiosity Learning the tools of trade, possibly to gain experience for bigger challenges
- 405. 382 Chapter 8: Network Security Policies, Vulnerabilities, and Protection Table 8-4 summarizes the actions taken by incident response teams. Table 8-4 Incident Response Team Actions Step Explanation 1 Verify the incident. Verify and gather details on the incident. 2 Determine the magnitude of the problem. Verify hosts and how they might have been affected. 3 Assess the damage. Determine what data has been manipulated. 4 Gather and protect the evidence. Restore the data and any software patches. Table 8-5 summarizes the methods used in common network attacks. Table 8-5 Network Attacks Attack Meaning Ping of death Attack that sends an improperly large ICMP echo request packet with the intent of overflowing the destination machine’s input buffers and causing it to crash. The IP protocol header field is set to 1, the last fragment bit is set, and the data length is greater than 65,535, greater than the maximum allowable IP packet size. TCP SYN Flood attacks This DoS attack randomly opens a number of TCP ports ensuring that network devices are using CPU cycles for bogus requests and denying other legitimate users access. Teardrop Exploits an overlapping IP fragment implementation bug in various operating systems. The bug causes the TCP/IP fragmentation re-assembly code to improperly handle overlapping IP fragments, causing the host to hang or crash. Land.C attacks A program designed to send TCP SYN packets (remember TCP SYN is used in the TCP connection phase) that specifies the target’s host address as both source and destination. This program can use TCP port 113 or 139 (source/destination), which can also cause a system to stop functioning. DNS poisoning The attacker exploits the DNS server, causing the server to return a false IP address to a domain name query. UDP Bomb Sends illegal length field in the packet header, causing Kernel panic and crash. E-mail attacks This DoS attack sends a random number of e-mails to a host. CPU-Intensive attacks This DoS attack ties up systems resources by using programs, such as TROJAN (a program designed to capture username or passwords from a network) or enables viruses to disable remote systems. Chargen attacks Establishes UDP services by producing a high character input. This can cause congestion on a network.
- 406. Foundation Summary 383 Table 8-5 Network Attacks (Continued) Attack Meaning Attacks via dialup (out of Applications, such as Windows 95, have built-in vulnerabilities on data band) port 139 (known as WinNuke), if the intruders can ascertain the IP address. Distributed Denial of A DDoS attack is a DoS attack run by multiple hosts. The attacker first Service compromises vulnerable hosts using various tools and techniques. Then, the actual DoS attack on a target is run from the pool of all these compromised hosts. Table 8-6 summarizes some of the critical IOS commands used to protect IOS-enabled routers. Table 8-6 Protecting Cisco IOS Routers IOS Command Meaning service nagle Enables the Nagle algorithm. no service udp-small-servers and By default, the TCP/UDP servers for Echo, Discard, Chargen, no service tcp-small-servers and Daytime services are disabled. service password-encryption Ensures that all passwords are encrypted and not viewable when viewing the IOS configuration file. service timestamps debug Enables the router to log any debug output and define each entry service timestamps log with a timestamp. service sequence-numbers Allows the syslog entries to be numbered to ensure that they are not tampered with.
- 407. 384 Chapter 8: Network Security Policies, Vulnerabilities, and Protection Q&A The Q & A questions are designed to help you assess your readiness for the topics covered on the CCIE Security written exam and those topics presented in this chapter. This format is intended to help you assess your retention of the material. A strong understanding of the answers to these questions can help you on the CCIE Security written exam. You can also look over the questions at the beginning of the chapter again for additional review. As an additional study aid, use the CD-ROM provided with this book to take simulated exams, which draw from a database of over 300 multiple-choice questions—all different from those presented in the book. Select the best answer. Answers to these questions can be found in Appendix A, “Answers to Quiz Questions.” 1 Define four reasons networks should be secured. 2 What is the function of the CERT/CC organization, and what are its primary objectives? 3 What are the primary steps completed by incident response teams? 4 Name common methods used by intruders to disrupt a secure network. 5 In security, what is session hijacking?
- 408. Q&A 385 6 In security terms, what is a man in the middle attack? 7 What is a Signature Engine? 8 What is social engineering? 9 Describe a ping of death attack. 10 What is a Land.C attack? 11 What does the following IOS code accomplish on a Cisco IOS router? no service udp-small-servers no service tcp-small-servers
- 409. 386 Chapter 8: Network Security Policies, Vulnerabilities, and Protection 12 What is the secret password for the following IOS configuration? enable secret %$@$%&^$@*$^*@$^* enable pass cisco 13 What is the purpose of the command service sequence-numbers?
- 410. Scenario 8-1: Defining IOS Commands to View DoS Attacks in Real Time 387 Scenario Scenario 8-1: Defining IOS Commands to View DoS Attacks in Real Time Figure 8-3 displays a typical two-router topology with an external connection to the Internet via R1. Figure 8-3 Two-Router Network Attacked by External Intruder Intruder Internet Connection Ethernet 0/1 131.108.100.5/24 131.108.101.1/24 131.108.200.5/24 Host A Host B .1 131.108.255.0/24 .2 R1 ICMP/TCP/UDP attack! R2 Administrator is not sure? Ethernet 0/0 Ethernet 0/0 131.108.100.1/24 131.108.200.1/24 In this scenario, a Cisco IOS router is subjected to ICMP, TCP, or UDP IP packets. The network administrator is not sure of what type but notices the log file that is buffered to the Router R2 has just increased from 1 MB to 2.5 MB in less than 5 seconds. What can be done to characterize the traffic and detect the type of denial-of-service attack?
- 411. 388 Chapter 8: Network Security Policies, Vulnerabilities, and Protection Scenario Answer Scenario 8-1 Solution The network administrator can quickly configure an extended access list permitting all ICMP, UDP, or TCP, as shown in Example 8-12, applying the access list to the inbound interface on R2, Serial 0/0. (The configuration is truncated to focus on the critical configuration.) Example 8-12 Access List Configuration on R2 Hostname R2 ! interface Serial0/0 ip address 131.108.255.2 255.255.255.252 ip access-group 100 in ! access-list 100 permit icmp any any log-input access-list 100 permit tcp any any log-input access-list 100 permit udp any any log-input ! End To determine the traffic type, access list 100 allows ICMP, UDP, and TCP inbound on Serial 0/0. Logging is also enabled with the keyword log-input. Assuming the DoS attack is taking place by viewing the access list 100 with the command show ip access-list 100, you can get an idea for which protocol type is being used. The displays in Example 8-13 are taken from R2 while the DoS attack is taking place. The command show ip access-list 100 is entered a few times on Router R2 to view the statistics and crucial bits of data that enable you to verify the source of the attack and the method, whether it is ICMP, TCP, or UDP. Logging has been enabled so the display in Example 8-13 describes what packet matches have been made and incremented each time a packet match is made on access list 100. Example 8-13 show ip access-list 100 on R2 (Repeated Five Times in Real Time) r2#show ip access-lists 100 Extended IP access list 100 permit icmp any any log-input (5000 matches) permit tcp any any log-input (100 matches) permit udp any any log-input (23 matches) r2#show ip access-lists 100 Extended IP access list 100 permit icmp any any log-input (25000 matches) permit tcp any any log-input (100 matches) permit udp any any log-input (24 matches) r2#show ip access-lists 100
- 412. Scenario 8-1 Solution 389 Example 8-13 show ip access-list 100 on R2 (Repeated Five Times in Real Time) (Continued) Extended IP access list 100 permit icmp any any log-input (35500 matches) permit tcp any any log-input (100 matches) permit udp any any log-input (25 matches) r2#show ip access-lists 100 Extended IP access list 100 permit icmp any any log-input (45500 matches) permit tcp any any log-input (100 matches) permit udp any any log-input (26 matches) r2#show ip access-lists 100 Extended IP access list 100 permit icmp any any log-input (67000 matches) permit tcp any any log-input (100 matches) permit udp any any log-input (26 matches) r2# Example 8-13 clearly shows that ICMP packets are increasing at an alarming rate. This indicates that an intruder could be attempting a Smurf attack (by sending a large number of ICMP requests). Now that you have identified the protocol type, you can take steps to stop ICMP packets from being sent to R2 by configuring the access list 100 on R1’s outbound interface to R2, as displayed in Example 8-14. Example 8-14 R1’s Access List 100 Configuration Hostname R1 ! interface Serial0/0 ip address 131.108.255.2 255.255.255.252 ip access-group 100 out ! access-list 100 deny icmp any any log-input access-list 100 permit tcp any any log-input access-list 100 permit udp any any log-input ! End You can also configure the Router R1 from the inbound Internet connection with the same access list denying ICMP inbound requests. This scenario is a simple one that clearly demonstrates the power of extended access lists and the simplest use of show commands that can be deployed in any medium or large IP network to quickly and safely identify and prevent some DoS attacks.
- 414. APPENDIX A Answers to Quiz Questions Chapter 2 “Do I Know This Already?” Quiz Answers 1 Which layer of the OSI model is responsible for converting frames into bits and bits into frames? a. Physical b. Network c. Transport d. LLC sublayer e. Data link Answer: e The data link layer performs bit conversion to pass to the MAC sublayer. 2 Routing occurs at what layer of the OSI model? a. Physical b. Network c. Transport d. LLC sublayer e. Data link Answer: b Routing is a Layer 3 (network layer) function. 3 Bridging occurs at what layer of the OSI model? a. Physical b. Network c. Transport d. Data link Answer: d The data link layer is where bridging is performed.
- 415. 490 Appendix A: Answers to Quiz Questions 4 Which of the following is not part of the OSI model? a. Network layer b. Physical layer c. Operational layer d. Application layer Answer: c The operational layer is not one of the seven OSI layers. The OSI model layers are physical, data link, network, transport, session, presentation, and application. 5 IP operates at what layer of the OSI model? a. Layer 1 b. Layer 2 c. Layer 3 d. Layer 4 e. Layer 5 f. Layer 6 g. Layer 7 Answer: c IP operates at the network layer (Layer 3) and provides a path to a destination. 6 On which layer of the OSI model is data commonly referred to as segments? a. Layer 4 b. Layer 3 c. Layer 2 d. Layer 1 Answer: a The data on Layer 4 is commonly referred to as segments.
- 416. Chapter 2 “Do I Know This Already?” Quiz Answers 491 7 On which layer of the OSI model is data commonly referred to as packets? a. Layer 1 b. Layer 2 c. Layer 4 d. Layer 3 Answer: d The data on Layer 3 is commonly referred to as packets. 8 Which layer of the OSI model transmits raw bits? a. Layer 1 b. Layer 2 c. Layer 3 d. Layer 4 Answer: a At Layer 1, the lowest layer of the OSI model, bits are transferred across the wire. 9 Which of the following protocols is not routable? a. IP b. IPX c. NetBEUI d. NetBIOS Answer: c NetBEUI is not a routed protocol and must be bridged. 10 Which of the following is not a required step to enable FastEther Channel (FEC)? a. Ensure that all ports share the same speed at 10 Mbps. b. Ensure that all ports share the same parameter such as speed. c. Ensure that all ports operate at 100 Mbps. d. Only eight ports can be bundled into a logical link or trunk. Answer: a FEC uses full-duplex Fast Ethernet (100 Mbps) links.
- 417. 492 Appendix A: Answers to Quiz Questions 11 How is FastEther Channel best defined? a. A bundle of 10-Mbps ports on a switch b. Another name for half duplex 100 Mbps c. Not available on Cisco Catalyst switches d. The ability to bundle 100 Mbps ports into a logical link e. Only supported with Gigabit ports Answer: d The FastEther Channel feature bundles 100 Mbps Fast Ethernet ports into a logical link between two devices, such as Catalyst switches. 12 On what OSI layer does bridging occur? a. Layer 1 b. Layer 2 c. Layer 3 d. Both Layer 1 and 2 Answer: b Bridging occurs at the data link layer (Layer 2) of the OSI model. 13 In spanning tree, what is a BPDU? a. A break protocol data unit b. A routable frame c. A bridge protocol data unit d. A frame sent out by end stations Answer: c BPDU is a bridge protocol data unit.
- 418. Chapter 2 “Do I Know This Already?” Quiz Answers 493 14 An incoming frame on a Layer 2 switch is received on port 10/1 on a Catalyst 5000. If the destination address is known through port 10/2, what happens? a. The frame is discarded. b. The frame is sent via port 10/2. c. The frame is broadcast to all ports on the switch. d. The frame is sent back via 10/1. e. None of the above. Answer: b The destination MAC address has already been discovered through port 10/2, so the frame will only be sent to the known port or slot 10, port 2. 15 Which of the following are the four possible states of spanning tree? a. Listening, learning, blocking, broadcasting b. Listening, learning, blocking, connecting c. Discovering, learning, blocking, connecting d. Listening, learning, blocking, forwarding Answer: d The four states of spanning tree are listening, learning, blocking, and forwarding. 16 How many bits make up an IP address? a. 64 bits b. 48 bits c. 32 bits d. 24 bits e. 8 bits Answer: c IP addresses for IPv4 are 32 bits in length.
- 419. 494 Appendix A: Answers to Quiz Questions 17 Identify the broadcast address for the subnet 131.108.1.0/24. a. 131.108.1.1 b. 131.108.1.254 c. 131.108.1.255 d. 131.108.1.2 e. More data required Answer: c 131.108.1.0/24 is a Class B address with a Class C mask, and the all (all binary 1s) broadcast address is 131.108.1.255 (11111111). 18 Convert the following address to binary: 131.1.1.1/24 a. 10000011.1.1.1 b. 10000011.00000010.1.1 c. 10000011.1.1.01010101 d. 10000011.1.1.11111111 Answer: a 131.108.1.1 in binary is 10000011.00000001.00000001.00000001 or 10000011.1.1.1 19 How many subnets are possible in VLSM if the Class C address 131.108.255.0 is used with the subnet mask 255.255.255.252 in the fourth octet field? a. None b. 100 c. 255 d. 254 e. 253 f. 252 g. 64 h. 62 Answer: h 26–2 = 64–2 = 62.
- 420. Chapter 2 “Do I Know This Already?” Quiz Answers 495 20 How many hosts are available when a /26 subnet mask is used? a. 254 b. 62 c. 64 d. 126 Answer: b 26–2 = 64–2 = 62. 21 How many hosts are available in a Class C or /24 network? a. 255 b. 254 c. 253 d. 0 e. More data required Answer: b A Class C or /24 network has 28–2 = 256–2 = 254 addresses available for host devices. 22 You require an IP network to support at most 62 hosts. What subnet mask will accomplish this requirement? a. 255.255.255.255 b. 255.255.255.252 c. 255.255.255.224 d. 255.255.255.192 e. 255.255.255.240 Answer: d 62 hosts require 62+2 = 64 addresses. This needs 6 bits borrowed from the subnet mask. In binary, that number is 11000000.
- 421. 496 Appendix A: Answers to Quiz Questions 23 Which of the following are multicast addresses? (Choose all that apply.) a. 224.0.0.5 b. 224.0.0.6 c. 221.0.0.5 d. 192.1.1.1 e. 131.108.1.1 Answer: a and b 224.0.0.5 and 224.0.0.6 are multicast addresses. 24 Which of the following routing protocols does not support VLSM? a. RIPv1 b. RIPv2 c. OSPF d. EIGRP e. BGP Answer: a RIP version I is classful and does not carry subnet masks in routing updates. 25 What is the source TCP port number when a Telnet session is created by a PC to a Cisco router? a. 23 b. Not a known variable c. 21 d. 20 e. 69 Answer: b The source TCP port is a random number; the destination port is 23.
- 422. Chapter 2 “Do I Know This Already?” Quiz Answers 497 26 What best describes the ARP process? a. DNS resolution b. Mapping an IP address to a MAC address c. Mapping a next-hop address to outbound interface on a Cisco router d. Both a and b Answer: b ARP maps an IP address to a MAC address. 27 If two Cisco routers are configured for HSRP and one router has a default priority of 100 and the other 99, which router assumes the role of active router? a. The default priority cannot be 100. b. The router with a higher priority. c. The router with the lowest priority. d. Neither router because Cisco routers do not support HSRP; only clients do. Answer: b The highest priority assumes the role of active router. 28 A Cisco router has the following route table: R1#show ip route 131.108.0.0/16 is variably subnetted, 17 subnets, 2 masks C 131.108.255.0/24 is directly connected, Serial0/0 C 131.108.250.0/24 is directly connected, Serial0/1 O 131.108.254.0/24 [110/391] via 131.108.255.6, 03:33:03, Serial0/1 [110/391] via 131.108.255.2, 03:33:03, Serial0/0 R 131.108.254.0/24 [120/1] via 131.108.255.6, 03:33:03, Serial0/1 [120/1] via 131.108.255.2, 03:33:03, Serial0/ What is the preferred path to 131.108.254.0/24? (Choose the best two answers.) a. Via Serial 0/0 b. Via Serial 0/1 c. None d. To null0 Answers: a and b OSPF is chosen because of the lower administrative distance of 110 compared to RIP’s 120. Also notice OSPF load balancing between Serial0/0 and Serial0/1. (The written examination always advises you how many answers to select. Practice on the CD provided.)
- 423. 498 Appendix A: Answers to Quiz Questions 29 IP RIP runs over what TCP port number? a. 23 b. 21 c. 69 d. 520 e. None of the above Answer: e IP RIP does not use TCP port numbers; it uses UDP. 30 IP RIP runs over what UDP port number? a. 23 b. 21 c. 69 d. 520 Answer: d UDP 520 31 An OSPF virtual link should . a. Never be used b. Allow nonpartitioned areas access to the backbone c. Allow partitioned areas access to the backbone d. Not be used in OSPF, but in ISDN Answer: c Virtual links allow access to areas not directly connected to the backbone or partitioned areas.
- 424. Chapter 2 “Do I Know This Already?” Quiz Answers 499 32 What is the BGP version most widely used today? a. 1 b. 2 c. 3 d. 4 e. 5 f. 6 Answer: d BGP4. 33 What is the destination port number used in a Telnet session? a. 23 b. 69 c. 21 d. 161 Answer: a Telnet, an application layer protocol, uses destination port 23. 34 In what fields does the IP checksum calculate the checksum value? a. Data only b. Header and data c. Header only d. Not used in an IP packet Answer: c The IP checksum calculation only covers the IP header. 35 The TCP header checksum ensures integrity of what data in the TCP segment? a. The data only. b. The header only. c. The data and header. d. There are no TCP header checksums; IP covers the calculation. Answer: c The TCP checksum calculation covers the TCP header and data.
- 425. 500 Appendix A: Answers to Quiz Questions 36 ISDN BRI channels are made up of what? a. 1 × 64 kbps channel and one D channel at 64 kbps b. 2 × 64 kbps channels and one D channel at 64 kbps c. 2 × 64 kbps channels and one D channel at 16 kbps d. 32 × 64 kbps channels and one D channel at 16 kbps Answer: c ISDN basic rate interface (BRI) is two 64-kbps data channels and one signaling channel (D Channel at 16 Kb). 37 What services can ISDN carry? a. Data only b. Data and voice only c. Voice and video d. Data, voice, and video Answer d. ISDN supports data, video, and voice. 38 Place the following steps in the correct order for PPP callback, as specified in RFC 1570. 1. A PC user (client) connects to the Cisco access server. 2. The Cisco IOS Software validates callback rules for this user/line and disconnects the caller for callback. 3. PPP authentication is performed. 4. Callback process is negotiated in the PPP link control protocol (LCP) phase. 5. The Cisco Access Server dials the client. a. 1, 2, 3, 4, 5 b. 1, 3, 2, 5, 4 c. 1, 4, 5, 3, 2 d. 5, 4, 3, 2, 1 Answer d. RFC 1570 dictates how PPP callback is to be followed. For more information, refer to www.cis.ohio-state.edu/cgi-bin/rfc/rfc1570.html.
- 426. Chapter 2 Q & A Answers 501 39 What hardware port is typically designed to connect a Cisco router for modem access? a. The console port b. The vty lines c. The auxiliary port d. The power switch e. The Ethernet interface Answer c. The auxiliary port on Cisco routers can be used for modem access. The console port can also be used but, typically, the Aux port is applied for remote access or dialup access for network failures. 40 The AS5300 series router can support which of the following incoming connections? a. Voice b. Dialup users via PSTN c. ISDN d. All the above Answer d. The AS5300 series router can support both digital (ISDN) and analogue connections, and also supports voice traffic. Chapter 2 Q & A Answers 1 What are the seven layers of the OSI model? Answer: The seven layers of the OSI model are as follows: • Application • Presentation • Session • Transport • Network • Data link • Physical
- 427. 502 Appendix A: Answers to Quiz Questions 2 What layer of the OSI model is responsible for ensuring that IP packets are routed from one location to another? Answer: The network layer is primarily responsible for routing IP packets from one destination to another. 3 What mechanism is used in Ethernet to guarantee packet delivery over the wire? Answer: Carrier Sense Multiple Access/Collision Detection (CSMA/CD) is the Ethernet mechanism used to ensure that when devices detect collisions, other devices on the segment are sent a jam signal. CSMA/CD ensures that when collisions occur, other devices (such as PCs or routers) back off (do not transmit) for a specified period of time. When a device receives a jam signal, it will wait a random amount of time to retransmit. This lowers the chance of another collision. All devices that detect a jam signal can transmit up to 16 times before sending an error message to the application layer. 4 Name two physical characteristics of 10BaseT? Answer: 10BaseT is an Ethernet physical layer standard that defines a maximum length of 100 m and a network speed of 10 Mbps. 5 What Catalyst command displays the bridging or CAM table on a Cisco 5000 series switch? Answer: show cam dynamic 6 What are the possible states of spanning tree? Answer: The possible states of spanning tree are as follows: • Disabled—The port is not participating in spanning tree and is not active. • Listening—The port has received data from the interface and will listen for frames. In this state, the bridge only receives data and does not forward any frames to the interface or to other ports. • Learning—In this state, the bridge still discards incoming frames. The source address associated with the port is added to the CAM table. BPDUs are sent and received. • Forwarding—The port is fully operational; frames are sent and received. • Blocking—The port has been through the learning and listening states and, because this particular port is a dual path to the root bridge, the port is blocked to maintain a loop-free topology. The order of spanning tree states is listening, then learning, and, finally, forwarding or blocking. Typically, each state takes around 15 seconds on Cisco Catalyst switches.
- 428. Chapter 2 Q & A Answers 503 7 FastEther Channel (FEC) allows what to occur between Cisco Catalyst switches? Answer: FEC is a Cisco method that bundles 100 MB/s fast Ethernet ports into a logical link between Cisco Catalysts switches, such as the Catalyst 5000 or 6000 series switches. Up to four ports can be bundled together to scale bandwidth up to 800 Mbps. 8 What field in the IP packet guarantees data delivery? Answer: The IP frame format has no settings that guarantee packet delivery, so IP is termed connectionless. The error check is only performed on the IP header fields, not the data in the packet. 9 Name some examples of connection-orientated protocols used in TCP/IP networks. Answer: Connection-orientated protocols include TCP, FTP, and Telnet. 10 Given the address, 131.108.1.56/24, what are the subnet and broadcast addresses? How many hosts can reside on this network? Answer: The subnet is 131.108.1.0 and the broadcast address is 131.108.1.255. The number of hosts is defined by the formula 28-2=256-2=254. 11 How many hosts can reside when the subnet mask applied to the network 131.108.1.0 is 255.255.255.128 (or 131.108.1.0/25)? Answer: The number of hosts is 27-2=128-2=126. 12 Name five routing protocols that support VLSM. Answer: Routing protocols that support VLSM include the following: • RIP Version II • OSPF • IS-IS • EIGRP • BGP4 13 What is the destination port number used in a Telnet session? Answer: The TCP port number is 23, and the source port is a random number generated by the host device.
- 429. 504 Appendix A: Answers to Quiz Questions 14 What TCP/IP services are common in today’s large IP networks? Answer: TCP/IP has a number of applications or services in use: • Address Resolution protocol (ARP) • Reverse Address Resolution protocol (RARP) • Dynamic Host Configuration Protocol (DHCP) • Hot Standby Router Protocol (HSRP) • Internet Control Message Protocol (ICMP) • Telnet • File transfer protocol (FTP) • Trivial File Transfer Protocol (TFTP) 15 What IOS command displays the IP ARP table on a Cisco IOS router? Answer: The IOS command is show ip arp. This command displays IP ARP entries only. IOS command, show arp, displays all ARP entries for all protocols in use. 16 Cisco routers use what mechanism to determine the routing selection policy for remote networks if more than one routing protocol is running? Answer: Cisco IOS routers use administrative distance, which defines a set number for every routing protocol in use. The lower the AD, the more trustworthy the network. For example, a static route (AD is 1) is preferred to an OSPF (AD is 110) discovered route. A static route pointing to a directly connected interface, for example, via ethernet0, has an AD set to 0, the same as a directly connected interface even though a static route is enabled. 17 What is the administrative distance for OSPF, RIP, and external EIGRP? Answer: The AD for RIP is 120, 110 for OSPF, and 170 for external EIGRP (internal EIGRP is 90).
- 430. Chapter 2 Q & A Answers 505 18 Name five characteristics of distance vector routing protocols and provide two examples of routing protocols classified as distance vector. Answer: Distance vector characteristics and example protocols are as follows: Periodic updates Periodic updates are sent at a set interval; for IP RIP, this interval is 30 seconds. Broadcast updates Updates are sent to the broadcast address 255.255.255.255. Only devices running routing algorithms will listen to these updates. Full table updates When an update is sent, the entire routing table is sent. Triggered updates Also known as Flash updates, triggered updates are sent when a change occurs outside the update interval. Split horizon This method stops routing loop. Updates are not sent out an outgoing interface from which the route was received. This also saves bandwidth. Maximum Hop Count For RIP, the limit is 15, and for IGRP it’s 255. limit Algorithm An example is Bellman-Ford for RIP. Examples RIP and IGRP. 19 IP RIP runs over what protocol and port number when sending packets to neighboring routers? Answer: UDP port number 520 20 How many networks can be contained in an IP RIP update? Answer: Up to 25 networks 21 Specify three main differences between RIPv1 and RIPv2? Answer: RIPv1 does not support VLSM, authentication, or multicast updates. RIPv2 supports VLSM, authentication, multicast updates, and unicast updates to remote routers. 22 What is an EIGRP Feasible Successor? Answer: An EIGRP Feasible Successor is a neighboring EIGRP Cisco router with a lower AD. 23 What is the metric used by OSPF? Answer: The metric used by OSPF is cost and is defined by the formula 108/ Bandwidth for a given interface. The cost to a remote path is the sum of all the costs that a packet will transverse to reach the remote network.
- 431. 506 Appendix A: Answers to Quiz Questions 24 If OSPF is configured for one area, what area assignment should be used? Answer: Good OSPF design defines area 0, or the backbone, as the core area, and area 0 should always be used. If the OSPF network resides in one area only, theoretically, any area assignment is possible. 25 What LSA types are not sent in a total stubby area? Answer: Totally stubby areas block LSA types 3, 4, and 5. Although similar to a stub area, a totally stubby area blocks LSAs of type 3, as well. This solution is Cisco proprietary and is used to further reduce a topological database. The only Link State Advertisement (LSA) type permitted is a specific type 3 LSA advertising a default router only. 26 What IOS command disables an interface from participating in the election of an OSPF DR/BDR router? Answer: To disable an interface on a Cisco router when electing a DR, the IOS command is ip ospf priority 0. The router with the highest priority (range is between 0 and 255) will be elected the DR. 27 On an Ethernet broadcast network, a DR suddenly reboots. When the router recovers and discovers neighboring OSPF routers, will it be the designated router once more? Answer: Once the router fails, the Backup DR (BDR) assumes the functions of the DR and another OSPF router (if it exists) is elected the BDR. After the failed router recovers, neighboring OSPF hello packets will advise that a DR/BDR already exists and there is no need to assume the functions of DR or BDR until another election process is initiated. 28 What Layer 4 protocol does BGP use to guarantee routing updates, and what destination port number is used? Answer: BGP4 uses TCP and the destination port number is 179. 29 What are ISDN BRI and PRI? Answer: ISDN can be supplied by a carrier in two main forms: Basic Rate Interface (BRI) and Primary Rate Interface (PRI). An ISDN BRI consists of two 64-kbps services (B channels) and one 16-kbps signaling channel (D channel). An ISDN PRI consists of 23 B or 30 B channels and a 64-kbps D channel, depending on the country. In North America and Japan, a PRI service consists of 23 B channels for a total bit rate of up to 1.544 Mbps. In Asia and Australia, a PRI delivers 30 B-channels and one 64-kbps D channel, delivering a total bit rate of 2.048 Mbps.
- 432. Chapter 2 Q & A Answers 507 30 What are the three phases that occur in any PPP session? Answer: The three phases that occur in any PPP session are • Link establishment—Link Control Program (LCP) packets are sent to configure and test the link. • Authentication (optional)—After the link is established, authentication can be used to ensure that link security is maintained. • Network layers—In this phase, NCP packets determine which protocols will be used across the PPP link. An interesting aspect of PPP is that each protocol (IP, IPX, and so on) supported in this phase is documented in a separate RFC that discusses how it operates over PPP. 31 Define what BECN and FECN mean in a Frame Relay network? Answer: Forward explicit congestion notification (FECN)—Bit set by a Frame Relay network device to inform DTE receiving the frame that congestion was experienced in the path from source to destination. DTE receiving frames with the FECN bit set can request that higher-level protocols take flow-control action, as appropriate. Backward explicit congestion notification (BECN)—Bit set by a Frame Relay network device in frames traveling in the opposite direction of frames encountering a congested path. DTE receiving frames with the BECN bit set can request that higher-level protocols take flow-control action, as appropriate. 32 Frame Relay DLCI values are used for what purpose? Answer: The data-link connection identifier (DLCI) value specifies a PVC or SVC in a Frame Relay network. DLCIs are locally significant. There are globally significant DLCIs used for LMI communication between Frame Relay switches. 33 What is the IP address range used in IP multicast networks? Answer: The range of networks is from 224.0.0.0 to 239.255.255.255. 34 What type of network environment typically uses an AS5300? Answer: The AS5300, or universal Access Server (AS), is a versatile data communi- cations platform that provides the functions of an access server, router, and digital modems in a single modular chassis. Internet Service Providers typically use AS5300 to allow clients to use ISDN or PSTN when accessing the Internet. The AS5300 also supports voice communication.
- 433. 508 Appendix A: Answers to Quiz Questions Chapter 3 “Do I Know This Already?” Quiz Answers 1 RFC 1700 defines what well-known ports for DNS? a. TCP port 21 b. TCP port 23 c. UDP port 21 d. UDP port 53 e. TCP/UDP port 53 Answer: e DNS is permitted by RFC 1700 to use both TCP/UDP port 53. Typically UDP is vendor-configured for UDP port 53. 2 What supplies DNS security? a. A default username/password pairing b. A TFTP directory c. A filename d. A domain name e. None of the above Answer: e DNS has no form of security, so any device can request name-to-IP address mappings. 3 What IOS command will stop a Cisco router from querying a DNS server when an invalid IOS command is entered on the EXEC or PRIV prompt? a. no ip domain-lookup b. no ip dns-lookup c. no ip dns-queries d. no exec Answer: a To disable DNS query lookup, the IOS command in global configuration mode is no ip domain-lookup.
- 434. Chapter 3 “Do I Know This Already?” Quiz Answers 509 4 What does the following Global IOS configuration line accomplish? ip host SimonisaCCIE 131.108.1.1 131.108.1.2 a. Defines the router name as SimonisaCCIE b. Defines a local host name, SimonisaCCIE, mapped to IP addresses 131.108.1.1 and 131.108.1.2 c. Configures the IOS router for remote routing entries 131.108.1.1 and 131.108.1.2 d. Not a valid IOS command e. Configures the local routers with the IP address 131.108.1.1 and 131.108.1.2 on boot up Answer: b The ip host name ip address1 [ipaddress2 ipaddress3 ipaddress4 ipaddress5 ipaddress6 ipaddress7 ipaddress8] command configures a local address lookup for the name SimonisaCCIE. Up to 8 addresses can be used. The router will try 131.108.1.1 first and, if no response is made by the remote host, the second address, 131.108.1.2, will be attempted from the command-line interface (CLI). 5 TFTP uses what predefined UDP port number? a. 21 b. 22 c. 23 d. 53 e. 69 Answer: e TFTP uses UDP port number 69. 6 What IOS command will copy an IOS image from the current system flash to a TFTP server? a. copy tftp image: b. copy flash tftp c. copy tftp flash d. copy tftp tftp Answer: b To copy an IOS image from the routers to system flash, the correct IOS command is copy flash tftp.
- 435. 510 Appendix A: Answers to Quiz Questions 7 Suppose a client calls and advises you that an FTP data transaction is not allowing him to view the host’s directory structure. What are the most likely causes of the problem? (Choose all that apply.) a. The client’s username/password is wrong. b. The client’s FTP data port is not connected. c. The host machine has denied him access because the password is wrong. d. A serious network outage requires that you reload the router closest to the client. e. An access list is stopping port 20 from detailing the directory list. Answers: b and e The FTP data port is used to view the directory and could be blocked because of an access list or a fault with the client’s software when establishing the FTP 20 connection. 8 FTP runs over what Layer 4 protocol? a. IP b. TCP c. TFTP d. DNS e. UDP Answer: b The FTP application is a connection-orientated protocol and is part of the TCP/IP protocol suite. FTP ensures data is delivered by running data with a TCP overhead. 9 HTTPS traffic uses what TCP port number? a. 21 b. 443 c. 334 d. 333 e. 343 Answer: b HTTPS runs over TCP port 443.
- 436. Chapter 3 “Do I Know This Already?” Quiz Answers 511 10 SNMP is restricted on Cisco routers by what IOS command? a. snmp-server enable b. snmp-server community string c. snmp-server ip-address d. snmp-server no access permitted Answer: b To restrict SNMP access, the correct IOS command is snmp-server community string. Without the correct string, NMS stations will not be able to access a router with SNMP queries. You can disable SNMP on a router and restrict SNMP access with the IOS command no snmp-server. 11 TFTP protocol uses which of the following? a. Username/password pairs to authorize transfers b. Uses TCP port 169 c. Uses UDP port 169 d. Can use UDP/TCP and port 69 e. None of the above Answer: d TFTP is defined in RFC 1700 and is permitted to use TCP/UDP port 69 only. 12 Which of the following statements is true regarding SSL? a. Every packet sent between host and client is authenticated. b. Encryption is used after a simple handshake is completed. c. SSL uses port 2246. d. SSL is not a predefined standard. e. SSL does not perform any data integrity checks. Answer: b After the hosts have negotiated with valid username/password pairs, SSL will start to encrypt all data. After the handshake, packets are not authenticated. SSL uses TCP port 443. RFC 2246 defines SSL.
- 437. 512 Appendix A: Answers to Quiz Questions 13 What is the HELO SMTP command used for? a. To authenticate SMTP clients b. To identify SMTP clients c. This is an unknown standard d. The HELO command is used in SNMP (not SMTP) Answer: b The HELO command identifies the client to the SMTP server. 14 POP3 clients can do what? a. Receive SNMP queries b. Send mail c. Send SNMP queries d. The POP3 protocol is a routing algorithm Answer: b POP3 clients send mail to POP3 servers. SMTP is not part of the POP3 standard. 15 NTP uses what well-known TCP port? a. 23 b. 551 c. 21 d. 20 e. 123 f. 321 Answer: e NTP uses UDP or TCP, and the port number is 123.
- 438. Chapter 3 “Do I Know This Already?” Quiz Answers 513 16 Secure Shell (SSH) is used to do what? a. Disable spanning tree on Catalyst 5000 switches b. Protect the data link layer only from attacks c. Protect the TCP/IP host d. Allow TCP/IP access to all networks without any security e. SSH is used only in the data link layer Answer: c SSH is used to protect TCP/IP hosts. 17 Which of the following protocols can be authenticated? (Select the best four answers.) a. Telnet b. HTTP c. HTTPS d. Spanning tree e. TFTP f. FTP Answers: a, b, c, and f 18 What is the community string value when the following IOS commands are entered in global configuration mode? snmp-server community publiC RO snmp-server enable traps config snmp-server host 131.108.255.254 isdn a. ISDN b. Config c. publiC d. public e. Public f. More data required Answer: c The community string is defined by the command snmp-server community community string, which, in this case, is set to publiC. The community string is case sensitive.
- 439. 514 Appendix A: Answers to Quiz Questions 19 Which of the following best describes an SNMP inform request? a. Requires no acknowledgment b. Requires an acknowledgment from the SNMP agent c. Requires an acknowledgment from the SNMP manager d. Only SNMP traps can be implemented on Cisco IOS routers Answer: c SNMP inform requests require an acknowledgment from the SNMP manager. SNMP hosts will continue sending the SNMP inform request until an acknowledgment is received. 20 What UDP port number will SNMP traps be sent from? a. 21 b. 22 c. 161 d. 162 Answer: d SNMP traps are sent by SNMP agents (such as routers) over UDP port 162. 21 What TCP port number will an SNMP inform acknowledgment packet be sent to? a. 21 b. 22 c. 23 d. 161 e. 162 f. None of the above Answer: d SNMP inform acknowledgments are sent over UDP (not TCP) port number 161.
- 440. Chapter 3 Q & A Answers 515 22 To restrict SNMP managers from the source network 131.108.1.0/30, what IOS command is required? a. ip http enable 131.108.1.1 131.108.1.2 b. snmp community 131.108.1.1 131.108.1.2 c. snmp-server community SimonisCool ro 4 access-list 4 permit 131.108.1.0 0.0.0.252 d. snmp-server community SimonisCool ro 4 e. snmp-server community SimonisCool ro 1 access-list 11 permit 131.108.1.0 0.0.0.252 Answer: c The SNMP server community name must be defined with the following command: snmp-server community string ro access-list-number The access list number definition must follow (in this case, number 4). The access list range is between 1 and 99 only. Chapter 3 Q & A Answers 1 According to RFC 1700, what is the well-known TCP/UDP port used by DNS? Answer: RFC 1700 defines the well-known ports for the whole TCP/IP protocol suite. For DNS, the well-known port for TCP/UDP is number 53. 2 What does the IOS command no ip domain-lookup accomplish? Answer: This IOS command disables DNS queries for network administrators connected to a Cisco console or vty line. 3 What is the correct IOS syntax to specify local host mapping on a Cisco router? Answer: Local host mappings to IP addresses are accomplished using the following IOS command: ip host name [tcp-port-number] ip address1 [ip address2...ip address8] Up to eight IP addresses can be assigned to one name.
- 441. 516 Appendix A: Answers to Quiz Questions 4 TFTP uses what well-known, defined TCP/UDP port? Answer: TFTP uses port number 69. 5 What is the correct IOS command to copy a file from a TFTP server to the system flash? Answer: The IOS command is copy tftp flash. To copy a file from the system flash to the TFTP server, the IOS command is copy flash tftp. 6 Define the two modes of FTP. Answer: FTP can be configured for the following two modes: • Active mode • Passive mode 7 FTP uses what TCP port numbers? Answer: FTP uses well-known port numbers 20 and 21. 8 What well-known port do Secure Socket Layer (SSL) and Secure Shell (SSH) use? Answer: SSL uses well-known port number 443. Secure Shell uses well-known TCP port 22. 9 Define SNMP and give an example. Answer: Simple Network Management Protocol (SNMP) is an application layer protocol that is used to manage IP devices. SNMP is part of the TCP/IP application layer suite. SNMP allows network administrators the ability to view and change network parameters and monitor connections locally and remotely. Cisco routers can be configured to send SNMP traps to network managing stations to alert administrators. For example, SNMP traps may indicate a router with low memory or high CPU usage. 10 What well-known UDP ports are used by SNMP? Answer: RFC 1700 defines the SNMP ports as 161 and 162. TCP can also be used, but vendors typically only implement SNMP with UDP. SNMP port 161 is used to query SNMP devices, and SNMP port 162 is used to send SNMP traps. SNMP runs over UDP and is secured by a well-known community string that is case sensitive. 11 What IOS command enables SNMP on a Cisco IOS router? Answer: The command syntax is snmp-server community string access-rights. The access-rights options are RO and RW. 12 Which TCP/UDP port numbers are defined for use by Network Time Protocol or NTP? Answer: NTP can use TCP and UDP port number 123.
- 442. Chapter 3 Q & A Answers 517 13 When defining a stratum value on a Cisco router, what is the range and what value is closest to an atomic clock? Answer: The stratum value ranges from 1 to 15. 1 represents an atomic clock, which is the most accurate clock available. The default stratum value on Cisco routers is 8. 14 Secure Shell (SSH) allows what to be accomplished when in use? Answer: Secure Shell (SSH) is a protocol that provides a secure connection to a router. Cisco IOS supports version 1 of SSH. SSH enables clients to make a secure and encrypted connection to a Cisco router. 15 What is the difference between an SNMP inform request and an SNMP trap? Answer: The major difference between a trap and an inform request is that an SNMP agent (when ending a trap) has no way of knowing if an SNMP trap was received by the SNMP manager. On the other hand, an SNMP inform request packet will be sent continually until the sending SNMP manager receives an SNMP acknowledgment. 16 What does the SNMP MIB refer to? Answer: The Management Information Base (MIB) is a virtual information storage area for network management information, which consists of collections of managed objects. MIB modules are written in the SNMP MIB module language, as defined in STD 58, RFC 2578, RFC 2579, and RFC 2580. 17 What is the SNMP read-write community string for the following router configuration? snmp-server community simon ro snmp-server community Simon rw Answer: The read-write community string is set to Simon (case sensitive). The read- only community attribute is set to simon. 18 Before you can TFTP a file from a Cisco router to a UNIX- or Windows-based system, what is the first step you must take after enabling the TFTP server daemon on both platforms? Answer: On a UNIX server where the TFTP server daemon is installed, the file to be copied must have the appropriate access rights. In UNIX, the Touch command allows a TFTP request. In other words, to copy a file from a Cisco IOS router to a UNIX host, the file must already exist on the host. For a Windows-based platform, the software must be configured to permit file creation on the Windows-based file system.
- 443. 518 Appendix A: Answers to Quiz Questions 19 What IOS command can be implemented to restrict SNMP access to certain networks by applying access lists? Can you apply standard, extended, or both? Answer: The IOS command is as follows: snmp-server community string [view view-name] [ro | rw] [number] You can only apply a standard access-list list with the above command. number refers to a standard access list, ranging from 1 to 99 only, that defines the remote hosts or subnets that are permitted SNMP access. The correct SNMP community string must also be correctly configured on the SNMP manger and agent to allow SNMP communication. 20 Does TFTP have a mechanism for username and password authentication? Answer: TFTP is a connectionless protocol (UDP) that has no method to authenticate username or password. The TFTP packet format has no field enabling the username or password to be exchanged between two TCP/IP hosts. TFTP security (configurable on UNIX and Windows platforms) on the TFTP server is accomplished by allowing a predefined file on the server to be copied to the host TFTP server. 21 Can you use your Internet browser to configure a Cisco router? If so, how? Answer: To view the router’s home page, use a Web browser pointed to http://a.b.c.d, where a.b.c.d is the IP address of your router or access server. If a name has been set, use http://router-name, and use the DNS server to resolve the IP address. To enable HTTP on a Cisco router, use the IOS command ip http in global configuration mode. 22 A network administrator defines a Cisco router to allow HTTP requests but forgets to add the authentication commands. What is the default username and password pairing that allows HTTP requests on the default TCP port 80? Can you predefine another TCP port for HTTP access other than port 80? Answer: By default Cisco IOS routers configured for HTTP access use the router’s local host name as the username and the enable or secret password as the password. The IOS command ip http [0-65535] allows the network administrator to define a new port number other than 80, which is the default setting.
- 444. Chapter 4 “Do I Know This Already?” Quiz Answers 519 Chapter 4 “Do I Know This Already?” Quiz Answers 1 What IOS command will display the System Flash? a. show flash b. show system flash c. show memory d. show process flash Answer: a The show flash IOS command displays the System Flash: R1#show flash System flash directory: File Length Name/status 1 11600424 c2600-ik8o3s-mz.122-2.T.bin [11600488 bytes used, 5176728 available, 16777216 total] 16384K bytes of processor board System flash (Read/Write) R1# 2 The network administrator has forgotten the enable password and all passwords are encrypted. What should the network administrator do to recover the password without losing the current configuration? a. Call the TAC and ask for a special back door password. b. Call the TAC and raise a case to supply the engineering password. c. Reboot the router, press the break key during the reload, and enter ROM mode and change the configuration register. d. Reboot the router, press the break key during the reload, enter ROM mode and change the configuration register, and when the router reloads, remove the old config- uration. Answer: c The TAC will not supply any passwords. The steps required include issuing the break key and modifying the configuration register, but the aim is to not lose the initial configuration, so answer d is incorrect.
- 445. 520 Appendix A: Answers to Quiz Questions 3 What is the enable password for the following router? enable password Simon a. More data required b. Simon c. simon or Simon d. You cannot set the password to a name; it must also contain digits. Answer: b The enable password is case-sensitive, so the password is Simon. 4 If the configuration register is set to 0x2101, where is the IOS image booted from? a. slot0: b. slot1: c. Flash d. ROM e. TFTP server Answer: d 0x2101 tells the router to load the IOS image from ROM. 5 What IOS command will copy the running configuration to a TFTP server? (Select the best two answers.) a. copy running-config to tftp b. write network c. copy running-config tftp d. write erase Answer: b and c Write network and copy running-config tftp will save the configuration stored in RAM to a TFTP server.
- 446. Chapter 4 “Do I Know This Already?” Quiz Answers 521 6 What debug command allows an administrator to debug only packets from the network 131.108.0.0/16? a. debug ip packet b. terminal monitor c. debug ip packet 1 access-list 1 permit 131.108.0.0 d. debug ip packet 1 access-list 1 permit 131.108.0.0 0.0.255.255 e. debug ip packet 1 access-list 1 permit 131.108.0.0 255.255.0.0 Answer: d To debug only packets from the source network 131.108.0.0/16, or networks ranging from 131.108.0.0 to 131.108.255.255, the correct access list is access-list 1 permit 131.108.0.0 0.0.255.255, followed by the debug ip packet 1 command in privilege EXEC mode. 7 After entering debug ip packet, no messages appear on your Telnet session. What is the likely cause? a. OSPF routing is required. b. The console port does not support debug output. c. The terminal monitor command is required. d. IP packets are not supported with the debug command. Answer: c Accessing a router via Telnet to enable debug messages to the terminal session requires the terminal monitor IOS command. 8 To change the configuration register to 0x2141, what is the correct IOS command? a. copy running-config register b. configuration 0x2141 c. config 0x2141 register d. config-register 0x2142 e. config-register 0x2141 Answer: e
- 447. 522 Appendix A: Answers to Quiz Questions 9 Where is the startup configuration stored on a Cisco router? a. In the cam table b. NVRAM c. RAM d. Flash e. slot0: Answer: b The startup configuration is usually stored in the NVRAM. You can store the file on a TFTP server, as well. 10 Which of the following statements is true? a. The enable secret command overrides the enable password command. b. The enable command overrides the enable secret password command. c. Enable passwords cannot be used when the secret password is used. d. Both a and c are true. Answer: a The enable secret command overrides the enable password command when configured concurrently. 11 A Cisco router has the following configuration: line vty 0 4 login What will happen when you Telnet to the router? a. You will be prompted for the login password. b. You will enter EXEC mode immediately. c. You cannot access the router without the password set. d. More configuration required. Answer: c Without the password configured, you cannot enter EXEC mode. The router will advise the Telnet user that the password is not set and disconnect the session, as follows: R1#131.108.1.1 Trying 131.108.1.1 ... Open Password required, but none set [Connection to 131.108.1.1 closed by foreign host]
- 448. Chapter 4 “Do I Know This Already?” Quiz Answers 523 12 A Cisco router has the following configuration: line vty 0 4 no login password cIscO When a Telnet user tries to establish a remote Telnet session to this router, what will happen? a. You will be prompted for the login password cIscO. b. You will enter EXEC mode immediately. c. You cannot access the router without the password set. d. More configuration required. e. You will be prompted for the login password; password case does not matter. Answer: b Because the no login command is configured, the VTY lines allow all Telnet sessions directly to the EXEC prompt even though a password is set. 13 A Cisco router has the following configuration: line vty 0 1 no login password cisco line vty 2 4 login password ciSco When a third Telnet session is established to a remote router with the preceding configuration, what will happen? a. You will be prompted for the login password, which is set to cisco. b. You will be prompted for the login password, which is set to ciSco. c. You will enter EXEC mode immediately. d. You cannot access the router without the password set. e. More configuration required. Answer: b The first two telnet sessions (line vty 0 1) will directly enter EXEC mode because of no login. The third (line vty 2 4) requires the password, ciSco.
- 449. 524 Appendix A: Answers to Quiz Questions 14 Which of the following access lists will deny any IP packets sourced from network 131.108.1.0/24 and destined for network 131.108.2.0/24 and permit all other IP-based traffic? a. access-list 1 deny 131.108.1.0 b. access-list 1 deny 131.108.1.0 0.0.0.255 c. access-list 100 permit/deny ip 131.108.1.0 0.0.0.255 131.108.2.0 0.0.0.255 d. access-list 100 deny ip 131.108.1.0 0.0.0.255 131.108.2.0 0.0.0.255 access-list 100 permit ip any any Answer: d The correct access list is an extended access list because both source and destination addresses must be configured. To permit all other traffic, you must add the line access-list permit ip any. Otherwise, all other IP-based traffic will be denied access by default. 15 An administrator notices a router’s CPU utilization has jumped from 2 percent to 100 percent, and that a CCIE engineer was debugging. What IOS command can the network administrator enter to stop all debugging output to the console and vty lines without affecting users on the connected router? a. no logging console debugging b. undebug all c. line vty 0 4 no terminal monitor d. reload the router Answer: b IOS command undebug all stops all configured debug commands. Reloading the router also stops debugs but will affect users because the router will be unavailable during the reboot. Entering no logging debugging does not stop the router from sending debug information nor processing the CPU-intensive requests to any connecting users via Telnet.
- 450. Chapter 4 Q & A Answers 525 Chapter 4 Q & A Answers 1 Where is the running configuration stored on a Cisco router? Answer: The configuration is stored in the Random Access Memory (RAM). For all newer Cisco hardware platforms, the memory location where the running configuration is stored is called the Dynamic Random-Access Memory (DRAM). 2 What IOS command displays the startup configuration? Answer: The IOS command show startup-config or show config will display the configuration stored in NVRAM. 3 What IOS command provides the following output? System flash directory: File Length Name/status 1 9558976 c2500-ajs40-l.12-17.bin [9559040 bytes used, 7218176 available, 16777216 total] 16384K bytes of processor board System flash Answer: The IOS command to display the System Flash is show flash. 4 What configuration register will enable a Cisco router to ignore the startup configuration? Answer: 0x2142 will set the IOS to ignore the configuration stored in NVRAM; typically, this configuration register is used for password recovery. 5 To copy the startup configuration to the running configuration, what IOS command or commands are used? Answer: copy startup-config running-config. 6 What is the range for standard and extended IP access lists on Cisco IOS routers? Answer: Standard IP access lists range from 1-99 and 1300-1999. Extended access lists range from 100-199 and 2000-2699. 7 What command display the IP access lists configured on a Cisco router? Answer: show ip access-lists will display all configured IP access lists. The show access-lists IOS command displays all configured access lists, not just IP access lists. 8 How do you disable all debug commands currently enabled on a Cisco router, assuming you are not sure what debug commands are enabled? Answer: undebug all (or u all in shorthand). You can also use the [no] debug <specific debug-enabled commands> for each specific debug that has been enabled. To quickly disable all debug commands, undebug all is typically used.
- 451. 526 Appendix A: Answers to Quiz Questions 9 What must you be very careful of when enabling any form of debugging on a Cisco router? Answer: You should make the debug command as specific as possible and ensure that you enable the output to the console (if disabled) and VTY lines with the IOS command, terminal monitor; this command is entered in privilege EXEC mode only. By default, Cisco IOS will send all debug output to the console port. The CPU system on Cisco routers gives the highest priority to debugging output. For this reason, debugging commands should be turned on only for troubleshooting specific problems or during troubleshooting sessions with technical support personnel. Excessive debugging output can render the router inoperable. Try to use the most specific debug command possible to reduce the load on the CPU. 10 What are the required steps when performing password recovery on a Cisco router? Answer: The password recovery steps are as follows: Step 1 Power cycle the router. Step 2 Issue a control break or the break key command on the application to enter into boot ROM mode. The control break key sequence must be entered within 60 seconds of the router restarting after a power cycle. Step 3 Once you are in ROM mode, change the config register value to ignore the startup configuration file that is stored in NVRAM. Use the o/r 0x2142 command. Step 4 Allow the router to reboot by entering the i command. Step 5 After the router has finished booting up without its startup configuration, look at the show startup-config command output. If the password is encrypted, move to Step 6, which requires you to enter the enable mode (type enable and you will not be required to enter any password) and copy the startup configuration to the running configuration with the copy startup-config running-config command. Then, change the password. If the password is not encrypted and the secret password is not used, you can simply read the password. Skip Steps 6 and 7 and go to Step 8. Step 6 Copy the startup configuration to RAM. Step 7 Enable all active interfaces. Step 8 Change the configuration register to 0x2102 (default). Step 9 Reload the router. Step 10 Check the new password.
- 452. Chapter 5 “Do I Know This Already?” Quiz Answers 527 11 What is the enable password for the following configuration? enable password CiscO Answer: Passwords are case-sensitive, so the password is CiscO. If the secret password was set, you would not be able to read the password in clear text because Cisco IOS hashes the password using the md5 encryption algorithm, as in the following example: enable secret 5 $1$Aiy2$GGSCYdG57PdRiNg/.D.XI. ➠ Password is not in clear text. You cannot reverse engineer the hashed password ($1$Aiy2$GGSCYdG57PdRiNg/ $1$Aiy2$GGSCYdG57PdRiNg/ .D.XI.). Hashing occurs when plain text data is encrypted into cipertext (unreadable .D.XI. data) by some form of encryption algorithm. Chapter 5 “Do I Know This Already?” Quiz Answers 1 What are the three components of AAA? (Choose the three best answers.) a. Accounting b. Authorization c. Adapting d. Authentication Answers: a, b, and d AAA is used for authentication, authorization, and accounting. Answer c is incorrect because adapting is not part of the security options available with AAA. 2 What IOS command must be issued to start AAA on a Cisco router? a. aaa old-model b. aaa model c. aaa new model d. aaa new-model e. aaa new_model Answer: d The aaa new-model command starts authentication, authorization and accounting (AAA). Answers a, b, and c are incorrect because they represent invalid IOS commands.
- 453. 528 Appendix A: Answers to Quiz Questions 3 What algorithm initiates and encrypts a session between two routers’ exchange keys between two encryption devices? a. Routing algorithm b. Diffie-Hellman algorithm c. The switching engine d. The stac compression algorithm Answer: b When using encryption between two routers, the Diffie-Hellman algorithm is used to exchange keys. This algorithm initiates the session between two routers and ensures that it is secure. Answer a is incorrect because the routing algorithm is used for routing, not for encryption. Answer c is incorrect because a switching engine is used to switch frames and has nothing to do with encryption. Answer d is incorrect because the stac compression algorithm is used by PPP; it compresses data on a PPP WAN link. 4 Can you configure RADIUS and TACACS+ concurrently on a Cisco IOS router? a. No. b. Yes, provided you have the same lists names applied to the same interfaces. c. Yes, provided you have the different lists names applied to the same interfaces. d. Yes, provided you have the different lists names applied to different interfaces. Answer: d List names and interfaces must be different. 5 How do you enable a RADIUS server to debug messages for Cisco Secure on a UNIX server? a. Terminal monitor b. Edit the configuration file on the router c. Edit the syslog.conf and csu.cfg files d. Not possible, as UNIX does not run IOS Answer: c You can enable debugging on a UNIX host running Cisco Secure by editing the syslog.confg and csu.cfg files.
- 454. Chapter 5 “Do I Know This Already?” Quiz Answers 529 6 What RADIUS attribute is used by vendors and not predefined by RFC 2138? a. 1 b. 2 c. 3 d. 4 e. 13 f. 26 g. 333 h. 33 Answer: f Attribute 26 is a vendor-specific attribute. Cisco uses vendor ID 9. 7 RADIUS can support which of the following protocols? a. PPP b. OSPF c. AppleTalk d. IPX e. NLSP Answer: a RADIUS supports PPP and none of the multiprotocols listed in options b, c, d, or e. 8 When a RADIUS server identifies the wrong password entered by the remote users, what packet type is sent? a. Accept-user b. Reject-users c. Reject-deny d. Reject-accept e. Reject-Error f. Access-reject Answer: f RADIUS sends an access-reject error if the password entered is invalid.
- 455. 530 Appendix A: Answers to Quiz Questions 9 Identify the false statement about RADIUS. a. RADIUS is a defined standard in RFC 2138/2139. b. RADIUS runs over TCP port 1812. c. RADIUS runs over UDP port 1812. d. RADIUS accounting information runs over port 1646. Answer: b RADIUS does not deploy TCP. 10 What is the RADIUS key for the following configuration? If this configuration is not valid, why isn’t it? aaa authentication login use-radius group radius local aaa authentication ppp user-radius if-needed group radius aaa authorization exec default group radius aaa authorization network default group radius radius-server 3.3.3.3 radius-server key IlovemyMum a. IlovemyMum b. Ilovemymum c. This configuration will not work because the command aaa new-model is missing. d. 3.3.3.3 Answer: c Because aaa new-model is not configured, this is not a valid configuration and no requests will be sent to the RADIUS server. 11 What is the RADIUS key for the following configuration? Aaa new-model aaa authentication login use-radius group radius local aaa authentication ppp user-radius if-needed group radius aaa authorization exec default group radius aaa authorization network default group radius radius-server 3.3.3.3 radius-server key IlovemyMum a. IlovemyMum b. Ilovemymum c. This configuration will not work d. 3.3.3.3 Answer: a The key is case-sensitive; the IOS command, radius-server key IlovemyMum, defines the key as IlovemyMum.
- 456. Chapter 5 “Do I Know This Already?” Quiz Answers 531 12 What versions of TACACS does Cisco IOS support? (Select the best three answers.) a. TACACS+ b. TACACS c. Extended TACACS d. Extended TACACS+ Answers: a, b, and c There is no Cisco Extended TACACS+ support. 13 TACACS+ is transported over which TCP port number? a. 520 b. 23 c. 21 d. 20 e. 49 Answer: e 14 What is the predefined TACACS+ server key for the following configuration? radius-server host 3.3.3.3 radius-server key CCIEsrock a. 3.3.3.3 b. Not enough data c. CCIESROCK d. CCIEsRock e. CCIEsrock Answer: e The key is case-sensitive and is defined by the IOS command, radius-server key CCIEsrock. CCIEsrock
- 457. 532 Appendix A: Answers to Quiz Questions 15 What does the following command accomplish? tacacs_server host 3.3.3.3 a. Defines the remote TACACS+ server as 3.3.3.3 b. Defines the remote RADIUS server as 3.3.3.3 c. Not a valid IOS command d. 3.3.3.3 e. Host unknown; no DNS details for 3.3.3.3 provided Answer: c The IOS command to define a remote TACACS+ server is tacacs-server host ip-address. 16 Which of the following protocols does TACACS+ support? a. PPP b. AppleTalk c. NetBIOS d. All the above Answer: d TACACS+ has multiprotocol support for PPP, AppleTalk, NetBIOS and IPX. 17 Kerberos is defined at what layer of the OSI model? a. Layer 1 b. Layer 2 c. Layer 3 d. Layer 4 e. Layer 5 f. Layer 6 g. Layer 7 Answer: g Kerberos is an application layer protocol defined at Layer 7 of the OSI model.
- 458. Chapter 5 “Do I Know This Already?” Quiz Answers 533 18 What definition best describes a key distribution center when Kerberos is applied to a network? a. A general term that refers to authentication tickets b. An authorization level label for Kerberos principals c. Applications and services that have been modified to support the Kerberos credential infrastructure d. A domain consisting of users, hosts, and network services that are registered to a Kerberos server e. A Kerberos server and database program running on a network host Answer: e The KDC is a server and database program running on a network host. 19 What definition best describes a Kerberos credential? a. A general term that refers to authentication tickets b. An authorization level label for Kerberos principals c. Applications and services that have been modified to support the Kerberos credential infrastructure d. A domain consisting of users, hosts, and network services that are registered to a Kerberos server e. A Kerberos server and database program running on a network host Answer: a A credential is a general term that refers to authentication tickets, such as ticket granting tickets (TGTs) and service credentials. Kerberos credentials verify the identity of a user or service. If a network service decides to trust the Kerberos server that issued a ticket, it can be used in place of retyping a username and password. Credentials have a default lifespan of eight hours.
- 459. 534 Appendix A: Answers to Quiz Questions 20 What definition best describes Kerberized? a. A general term that refers to authentication tickets b. An authorization level label for Kerberos principals c. Applications and services that have been modified to support the Kerberos credential infrastructure d. A domain consisting of users, hosts, and network services that are registered to a Kerberos server e. A Kerberos server and database program running on a network host Answer: c Kerberized refers to applications and services that have been modified to support the Kerberos credential infrastructure. 21 What definition best describes a Kerberos realm? a. A general term that refers to authentication tickets b. An authorization level label for the Kerberos principals c. Applications and services that have been modified to support the Kerberos credential infrastructure d. A domain consisting of users, hosts, and network services that are registered to a Kerberos server e. A Kerberos server and database program running on a network host Answer: d The Kerberos realm is also used to map a DNS domain to a Kerberos realm. 22 What IOS command enables VPDN in the global configuration mode? a. vpdn-enable b. vpdn enable c. vpdn enable in interface mode d. Both a and c are correct Answer: b To Enable VPDN in global configuration mode, the correct IOS command is vpdn enable.
- 460. Chapter 5 “Do I Know This Already?” Quiz Answers 535 23 What is the number of bits used with a standard DES encryption key? a. 56 bits b. 32 bits; same as IP address c. 128 bits d. 256 bits e. 65,535 bits f. 168 bits Answer: a DES applies a 56-bit key. The documented time taken to discover the 56-bit key is 7 hours on a Pentium III computer, so DES is not a common encryption algorithm used in today’s networks. 24 What is the number of bits used with a 3DES encryption key? a. 56 bits b. 32 bits; same as IP address c. 128 bits d. 256 bits e. 65,535 bits f. 168 bits Answer: f Triple DES (3DES) is today’s standard encryption with a 168-bit key. 25 In IPSec, what encapsulation protocol only encrypts the data and not the IP header? a. ESP b. AH c. MD5 d. HASH e. Both a and b are correct Answer: a ESP only encrypts the data, not the IP header.
- 461. 536 Appendix A: Answers to Quiz Questions 26 In IPSec, what encapsulation protocol encrypts the entire IP packet? a. ESH b. AH c. MD5 d. HASH e. Both a and b are correct Answer: b AH encrypts the entire IP packet. The time to live (TTL) is not encrypted because this value decreases by one (1) every time a router is traversed. 27 Which of the following is AH’s destination IP port? a. 23 b. 21 c. 50 d. 51 e. 500 f. 444 Answer: d The AH destination port number is 51. 28 Which of the following is ESP’s destination IP port? a. 23 b. 21 c. 50 d. 51 e. 500 f. 444 Answer: c The ESP destination IP port number is 50.
- 462. Chapter 5 “Do I Know This Already?” Quiz Answers 537 29 Which of the following is not part of IKE phase I negotiations? a. Authenticating IPSec peers b. Exchanges keys c. Establishes IKE security d. Negotiates SA parameters Answer: d IKE phase II negotiates SA parameters. 30 Which of the following is not part of IKE phase II? a. Negotiates IPSec SA parameters b. Periodically updates IPSec SAs c. Rarely updates SAs (at most, once a day) d. Established IPSec security parameters Answer: c IKE phase II updates SAs at periodically-defined intervals. 31 Which is the faster mode in IPSEC? a. Main mode b. Fast mode c. Aggressive mode d. Quick mode Answer: c Aggressive mode is faster than Main mode but is less secure. They can both occur in Phase I. Phase II only has Quick mode. Fast mode does not exist in the IPSec standard set of security protocols.
- 463. 538 Appendix A: Answers to Quiz Questions 32 Certificate Enrollment Process (CEP) runs over what TCP port number? (Choose the best two answers.) a. Same as HTTP b. Port 80 c. Port 50 d. Port 51 e. Port 333 f. Port 444 Answers: a and b CEP uses the same port as HTTP, port 80. Chapter 5 Q & A Answers 1 Define the AAA model and a typical application on a Cisco IOS router. Answer: Authentication, authorization, and accounting (pronounced triple A) provides security to Cisco IOS routers and network devices beyond the simple user authentication available on IOS devices. AAA provides a method to identify which users are logged into a router and each user’s authority level. AAA also provides the capability to monitor user activity and provide accounting information. Typically, AAA is used to authenticate and authorize Cisco IOS commands, and provides accounting information to the network administrator. 2 Can you allow a remote user authorization before the user is authenticated with AAA? Answer: Before authorization occurs, the remote user must be authenticated. Cisco IOS routers allow you to configure AAA authorization, but no access will be permitted until the remote user is authenticated. 3 What IOS command is required when enabling AAA for the first time? Answer: aaa new-model must be entered globally before additional IOS commands are entered.
- 464. Chapter 5 Q & A Answers 539 4 What is the privilege level of the following user? Assume AAA is not configured. R2> Answer: The privilege level ranges from 0 to 15 (the higher the level, the more commands are available). Because the user is not in PRIV exec mode, the default privilege level for an EXEC user is 1. Only basic show commands are available in priv level 1. R2>show priv Current privilege level is 1 5 Define four possible RADIUS responses when authenticating the user through a RADIUS server. Answer: The four possible responses are as follows: • ACCEPT—The user is authenticated. • REJECT—The user is not authenticated and is prompted to reenter the username and password, or access is denied. The RADIUS server sends this response when the user enters an invalid username/password pairing. • CHALLENGE—The RADIUS server issues a challenge. The challenge collects additional data from the user. • CHANGE PASSWORD—The RADIUS server issues a request asking the user to select a new password. 6 What are RADIUS attributes? Supply five common examples. Answer: RADIUS supports a number of predefined attributes that can be exchanged between client and server, such as the client’s IP address. RADIUS attributes carry specific details about authentication. RFC 2138 defines a number of RADIUS predefined attributes. The following bulleted lists provides details from the most common attributes: • Attribute type 1—Username (defined usernames can be numeric, simple ASCII characters, or an SMTP address) • Attribute type 2—Password (defines the password; passwords are encrypted using MD5) • Attribute type 3—CHAP Password (only used in access-request packets) • Attribute type 4—NAS IP address (defines the NAS server’s IP address; only used in access-request packets) • Attribute type 5—NAS port (not UDP port number); and indicates that the NAS’s physical port number ranges from 0 to 65535 • Attribute type 6—Service-type (type of service requested or type of service to be provided); for Cisco devices is Callback and is not supported
- 465. 540 Appendix A: Answers to Quiz Questions • Attribute type 7—Protocol (defines what framing is required; for example, PPP is defined when this attribute is set to 1, SLIP is 2) • Attribute type 8—IP address (defines the IP address to be used by the remote user) • Attribute type 9—IP subnet mask (defines the subnet mask to be used by the remote user) • Attribute type 10—Routing • Attribute type 13—Compression • Attribute type 19—Callback number • Attribute type 20—Callback ID • Attribute type 26—Vendor-specific (Cisco [vendor-ID 9] uses one defined option, vendor type 1, named cisco-avpair) 7 What protocols does RADIUS use when sending messages between the server and client? Answer: RADIUS transports through UDP destination port number 1812. 8 What predefined destination UDP port number is RADIUS accounting information sent to? Answer: UDP port 1646 9 What does the following command accomplish on a Cisco IOS router? aaa authentication ppp user-radius if-needed group radius Answer: The aaa authentication ppp user-radius if-needed group radius command configures the Cisco IOS software to use RADIUS authentication for lines using PPP with CHAP or PAP, if the user has not already been authorized. If the EXEC facility has authenticated the user, RADIUS authentication is not performed. User-radius is the name of the method list that defines RADIUS as the if-needed authentication method. 10 What is the RADIUS server IP address and key for the following configuration? radius-server host 3.3.3.3 radius-server key GuitarsrocKthisplaneT Answer: The radius-server host command defines the RADIUS server host’s IP address. The IP address is 3.3.3.3. The radius-server key command defines the shared secret text string between the NAS and the RADIUS server host. The key is case-sensitive like all passwords on Cisco IOS devices, so the key is defined as GuitarsrocKthisplaneT. 11 TACACS+ is transported over what TCP destination port number? Answer: TCP port 49
- 466. Chapter 5 Q & A Answers 541 12 What information is encrypted between a Cisco router and a TACACS+ server? Answer: All data communication between TACACS+ devices is encrypted, excluding the IP header. 13 What are the four possible packet types from a TACACS+ server when a user attempts to authenticate a Telnet session to a Cisco router configured for AAA, for example? Answer: The four packets types are as follows: • ACCEPT—The user is authenticated and service can begin. If the network access server is configured to require authorization, authorization will begin at this time. • REJECT—The user has failed to authenticate. The user can be denied further access or will be prompted to retry the login sequence, depending on the TACACS+ daemon. • ERROR—An error occurred at some time during authentication. This can be either at the daemon or in the network connection between the daemon and the NAS. If an ERROR response is received, the network access server typically tries to use an alternative method for authenticating the user. • CONTINUE—The user is prompted for additional authentication information. 14 What is the significance of the sequence number in the TACACS+ frame format? Answer: The sequence number is the number of the current packet flow for the current session. The sequence number starts with 1 and each subsequent packet will increment by one. The client only sends odd numbers. TACACS+ servers only send even numbers. 15 What does the following IOS command accomplish? aaa authentication ppp default if-needed group tacacs+ local Answer: The aaa authentication command defines a method list, “default,” to be used on serial interfaces running PPP. The keyword default means that PPP authentication is applied by default to all interfaces. The if-needed keyword means that if the user has already authenticated through the ASCII login procedure, PPP authentication is not necessary and can be skipped. If authentication is needed, the keyword group tacacs+ means that authentication will be done through TACACS+. If TACACS+ returns an ERROR during authentication, the keyword local indicates that authentication will be attempted using the local database on the NAS. 16 What IOS command defines the remote TACACS+ server? Answer: To define the TACACS+ server, the IOS command is tacacs-server host ip address.
- 467. 542 Appendix A: Answers to Quiz Questions 17 What are the major difference between TACACS+ and RADIUS? Answer: The following table lists the major differences between TACACS+ and RADIUS. RADIUS TACACS+ Packet delivery UDP TCP Packet encryption RADIUS encrypts only the TACACS+ encrypts the password in the access- entire body of the packet, request packet, from the but leaves a standard client to the server. TACACS+ header. AAA support RADIUS combines TACACS+ uses the AAA authentication and architecture, separating authorization. authentication, authorization, and accounting. Multiprotocol support None. TACACS+ supports other protocols, such as AppleTalk, NetBIOS, and IPX. Router management RADIUS does not allow TACACS+ allows network users to control which administrators control over commands can be executed which commands can be on a router. executed on a router. 18 Kerberos is a third-party authentication protocol operating at what layer of the OSI model? Answer: Kerberos is an application layer protocol, which operates at Layer 7 of the OSI model. 19 What delivery methods and destination ports does Kerberos support? Answer: Kerberos supports both TCP and UDP, including the following port numbers: • TCP/UDP ports 88, 543, and 749 • TCP ports 754, 2105, and 4444 20 What does the Kerberos realm define? Answer: A Kerberos realm defines a domain consisting of users, hosts, and network services that are registered to a Kerberos server. The Kerberos server is trusted to verify the identity of a user or network service to another user or network service. Kerberos realms must always be in uppercase characters.
- 468. Chapter 5 Q & A Answers 543 21 Applications that have been modified to support Kerberos credential infrastructures are known as what? Answer: Kerberized. 22 Define the two steps required in an L2F connection terminating a PPP connection? Answer: For L2F, the setup for tunneling a PPP session consists of two steps: Step 1 Establish a tunnel between the NAS and the Home Gateway (HWY). The HWY is a Cisco router or access server (for example, an AS5300) that terminates VPDN tunnels and PPP sessions. This phase takes place only when no active tunnel exists between both devices. Step 2 Establish a session between the NAS and the Home Gateway. 23 Define the two steps for setting up L2TP for tunneling a PPP connection. Answer: For L2FP, the setup for tunneling a PPP session consists of two steps: Step 1 Establish a tunnel between the LAC and the LNS. The LAC is an L2TP access concentrator that acts as one side of the L2TP tunnel endpoint and has a peer to the L2TP network server or LNS. This phase takes place only when no active tunnel exists between both devices. Step 2 Establish a session between the LAC and the LNS. 24 What are the steps taken for a VPDN connection between a remote user and a remote LAN? Answer: A VPDN connection between a remote user (router or via PSTN) and the remote LAN is accomplished in the following steps: Step 1 The remote user initiates a PPP connection to the ISP using the analog telephone system or ISDN. Step 2 The ISP network access server accepts the connection. Step 3 The ISP network access server authenticates the end user with CHAP or PAP. The username determine whether the user is a VPDN client. If the user is not a VPDN client, the client accesses the Internet or other contacted service. Step 4 The tunnel endpoints—the NAS and the home gateway—authenticate each other before any sessions are attempted within a tunnel. Step 5 If no L2F tunnel exists between the NAS and the remote users’ home gateway, a tunnel is created. Once the tunnel exists, an unused slot within the tunnel is allocated.
- 469. 544 Appendix A: Answers to Quiz Questions Step 6 The home gateway accepts or rejects the connection. Initial setup can include authentication information required to allow the home gateway to authenticate the user. Step 7 The home gateway sets up a virtual interface. Link-level frames can now pass through this virtual interface through the L2F or L2TP tunnel. 25 What are the three most common threats from intruders that network administrators face? Answer: The most common attacks are as follows: • Packet snooping (also known as eavesdropping)—When intruders capture and decode traffic obtaining usernames, passwords, and sensitive data, such as salary increases for the year. • Theft of data—When intruders use sniffers, for example, to capture data over the network and steal that information for later use. • Impersonation—When an intruder assumes the role of a legitimate device but, in fact, is not legitimate. 26 What does the Digital Signature standard provides Answer: DSS is a mechanism that protects data from an undetected change while traversing the network. DSS verifies the identity of the person sending the data just as you verify your license signature to the bank manager. 27 What is hash in encryption terminology? Answer: A hash is defined as the one-way mathematical summary of a message (data) such that the hash value cannot be easily reconstructed back into the original message. 28 Name the two modes of operation in IPSec and their characteristics. Answer: The two modes are transport and tunnel mode. • Transport mode—Protects payload of the original IP datagram; typically used for end-to-end sessions. • Tunnel Mode—Protects the entire IP datagram by encapsulating the entire datagram in a new IP datagram. 29 What does IKE accomplish? Answer: IKE negotiates and provides authenticated keys in a secure manner. IKE was developed by the company previously known as ISAKMP Oakley Key Resolution. 30 Certificate Enrollment Protocol is transported over what TCP port? Answer: CEP is transported over TCP port 80 (same as HTTP).
- 470. Chapter 6 “Do I Know This Already?” Quiz Answers 545 Chapter 6 “Do I Know This Already?” Quiz Answers 1 What UNIX command implements a trace route to the remote network www.guitar.com? a. trace www.guitar.com if DNS is enabled with the IOS command dns server ip-address. b. traceroute www.guitar.com c. trace guitar.com d. UNIX does not support the traceroute command. Answer: b 2 What UNIX command copies a file? a. copy b. cpy c. cp d. pc Answer: c 3 A Cisco router network manager wants to copy the configuration in RAM to a UNIX server. What needs to be accomplished before this can occur? a. Issue copy run tftp. b. Modify the .rhosts file. c. Modify the rcmd.allow file. d. Erase the .rhosts.allow file. e. Enable TFTP on the UNIX server. Answer: b 4 Which of the following is not a UNIX file flag parameter? a. Execute b. Write c. Read d. Read/Write e. Authenticate Answer: e
- 471. 546 Appendix A: Answers to Quiz Questions 5 Which of the following is not a UNIX file type? a. Normal b. Directories c. Special d. Link e. Medium Answer: e 6 NetBIOS over TCP/IP operates at what layer of the OSI model? a. 1 b. 2 c. 3 d. 4 e. 5 f. 6 g. 7 Answer: e 7 In Windows NT, what is a domain that is trusted by all remote domains called? a. Local b. Remote c. Single d. Global e. Master f. Slave Answer: e
- 472. Chapter 6 “Do I Know This Already?” Quiz Answers 547 8 In Windows NT, what is a domain that is trusted automatically called? a. Local b. Remote c. Single d. Global e. Master f. Slave Answer: d 9 Which of the following is not an NTFS permission type? a. R b. W c. D d. P e. O f. M Answer: f 10 In Windows NT, when in a DOS command window, what command displays the local IP ARP entries? a. arp b. rarp c. rarp –b d. arp –n e. arp –a Answer: e
- 473. 548 Appendix A: Answers to Quiz Questions 11 What devices can the Cisco Secure Policy Manager remotely manage? (Select the best three answers.) a. Routers b. Switches c. NMS workstations d. PIX Firewalls Answers: a, b, and d 12 NetRanger LAN interface supports all but which one of the following? a. Ethernet b. Fast Ethernet c. Token Ring d. Serial WAN interfaces e. FDDI Answer: d 13 Which of the following is not a component of the security wheel? a. Develop b. Secure c. Monitor d. Manage e. Increase Answer: e 14 Which of the following is false in regards to NetRanger? a. NetRanger examines the IP header. b. NetRanger examines the TCP header. c. NetRanger examines the entire IP frame. d. NetRanger monitors TCP or UDP port scans. Answer: c
- 474. Chapter 6 Q & A Answers 549 15 How many phases are completed with NetSonar? a. 1 b. 2 c. 3 d. 4 e. 5 f. 6 Answer: f Chapter 6 Q & A Answers 1 What UNIX command displays the files in the current directory? Answer: ls 2 What UNIX command changes a directory from etc/ to bin/? Answer: cd .. (takes you down one directory) cd etc (root directory to etc directory) 3 What does the following UNIX command accomplish? cp -i simon.doc henry.doc Answer: This command makes a copy of the files simon.doc and henry.doc. You must specify the name of the file to be copied and the name of the new file to be created. The -i flag tells the computer to ask before it overwrites any files in this process. The -r flag copies any files in subdirectories if you are copying directories. 4 To define a permission for a UNIX file, what command line interface is required? Answer: chmod flag filename 5 The chmod UNIX command can define what levels of access or permissions on a UNIX host? Answer: The chmod flag is always three numbers. The first number affects the owner permissions, the second number affects the group permissions, and the third number affects all other permissions. Each number can be a number between 0 and 7. See Table 6-3 for an explanation of these levels.
- 475. 550 Appendix A: Answers to Quiz Questions 6 In a Windows NT environment, what is a domain, primary domain controller, and backup domain controller? Answer: A domain is typically a large group of devices under a common administra- tion. A domain is managed by a primary domain controller (PDC), which is a Windows- based server that stores and controls security and user account information for an entire domain. Each domain must have at least one PDC. A backup domain controller (BDC) maintains a copy of the database in the event the PDC is unavailable. 7 What functions does the protocol NetBIOS provide in a Window NT environment? Answer: NetBIOS is a session layer protocol that is used to allow communication between PCs. NetBIOS provides the following functions: Authentication Connection management Error control File sharing Flow control Full-duplex transmissions Name resolution Print sharing Session management 8 What is the function of the lmhosts file on a Windows platform device? Answer: The lmhosts file enables local PCs to maintain a static list of all computers available in the network. The file typically contains the name and protocol addresses of all servers available in the domain. For large networks, the file might become too large and unusable, so a service called Windows Internet Naming Services (WINS) was developed to help network administrators who had to previously modify every Windows PC on the network via the lmhosts files. WINS allows NetBIOS Windows- based systems running TCP/IP to perform a name lookup for Windows resources, such as remote servers. An excellent white paper on WINS is available at www.lucent.com/livelink/09009403800049fc_White_paper.pdf.
- 476. Chapter 6 Q & A Answers 551 9 Name and define the six NTFS permission types. Answer: The six NTFS permissions are as follows: R—Read only. The data or object can only be viewed. W—Write access. The data can be changed. X—Execute. The data can be executed; for example, a directory can be viewed or program executed. D—Delete. The data can be deleted. P—Change permissions. The data access permissions can be altered. O—Take ownership. The ownership can be altered. 10 In Windows NT 4.0, what DOS command displays any local ARP entries? Answer: arp -a 11 Define the terms NetRanger Sensor and Director and their uses? Answer: NetRanger has two components: NetRanger Sensor—High speed device that analyzes the content of data being transported across a network and determines whether that traffic is authorized or unauthorized. Unauthorized traffic includes ping requests from intruders. Traffic that is detected from unauthorized sources is sent directly to the NetRanger Director, and the intruder is removed from the network (optional and set by network administrator). NetRanger Director—Provides real-time response to intruders in the network by blocking access to the network and terminating any active data sessions. 12 What LAN interfaces can be supported on a NetRanger Sensor? Answer: NetRanger supports Ethernet (10 or 100 MB), Token Ring, and FDDI LAN interfaces. 13 What are the six phases completed by Cisco NetSonar? Answer: The six phases completed by NetSonar are as follows: Phase I—NetSonar sends out ICMP echo requests (ping) to query hosts. Phase II—All live hosts are collected and stored on particular port numbers. Phase III—NetSonar identifies the hardware devices that might be vulnerable, such as routers, switches, firewalls, printers, desktops, and hosts that responded to ping requests. Operating systems and network services are documented and labeled as potential vulnerabilities.
- 477. 552 Appendix A: Answers to Quiz Questions Phase IV—Vulnerabilities are confirmed. This phase is intrusive. Phase V—The data is charted for presentation. The data can also be charted graphically as line or 3D bar graphs. Phase VI—The data is reported in a number of different formats, including a summary report, a short and detailed report, or a full technical report. 14 What is the meaning of the term Security Wheel? Answer: Cisco defines a Security Wheel concept that outlines the critical steps to ensuring that data and networks are secured correctly. The Security Wheel revolves around a strong, well-defined corporate policy. The Security Wheel consists of the following: Secure—After defining a strong corporate policy, you should secure your network by deploying the products necessary in the appropriate places to achieve your corporate security policy. Monitor and respond—Continuously monitor using NetRanger tools at strategic points in the network to discover new vulnerabilities. Test—On a regular and formal basis, test all network components. Manage and improve—Analyze all the reports and metrics supplied by NetSonar, and cycle through the Security Wheel by going through all these steps continuously. Chapter 7 “Do I Know This Already?” Quiz Answers 1 DMZ stands for what? a. Demilitarized zone b. Demitted zone c. Domain main zone d. Domain name Answer: a 2 When defining an extended access list, what TCP port numbers can you use? a. Only predefined Cisco keywords b. 0 to –65,000 c. 0 to –65,535 d. 1 to 65,534 e. None of the above Answer: c TCP port numbers from 0 to –65,535; devices such as PCs go from 1025 to 65535.
- 478. Chapter 7 “Do I Know This Already?” Quiz Answers 553 3 When defining an extended access list, what UDP port numbers can you use? a. Only predefined Cisco keywords b. 0 to 65000 c. 0 to 65535 d. 1 to 65534 e. None of the above Answer: c UDP port numbers from 0 to 65535. 4 Which of the following is not a TCP service? a. who b. whois c. finger d. ftp e. pop3 Answer: a who is a UDP service. 5 Which of the following is not a UDP service? a. BGP b. echo c. domain d. discard e. rip f. snmp Answer: a BGP runs over TCP port 179.
- 479. 554 Appendix A: Answers to Quiz Questions 6 For how many translations does PAT allow you to use one IP address? a. 32,000 b. 64,000 c. 96,000 d. 128,000 e. 256,000 Answer: b Port Address Translation (PAT) occurs when the local port number is modified, allowing more than one host the ability to share one public address, for example. The Port number in a TCP frame can be numbered from 0 to –65,535, so answer b is closet to the actual number of allowed translations. 7 PAT translates all private addresses based on what? a. Source port b. Destination port c. Both source and destination d. None Answer: c PAT is based on source port; the destination port is not altered. For example, a Telnet connection is based on the local port number (a random number generated by the device between 0 and –65,535) and the destination port number 23. 8 NAT is which of the following? a. Network Architectural Language b. National anthem of Latvia c. Network translation d. Network Address Translation Answer: d
- 480. Chapter 7 “Do I Know This Already?” Quiz Answers 555 9 NAT is defined in which RFC? a. 1700 b. 1701 c. 2002 d. 1631 e. 1613 Answer: d NAT is defined by Request for comment (RFC) number 1631. 10 The following defines which NAT terminology: “A legitimate registered IP address as assigned by the InterNIC?” a. Inside local address b. Outside global address c. Inside global address d. Outside local address Answer: c 11 What IOS command defines a pool of addresses that will be translated to a registered IP address? a. ip nat inside b. ip nat outside c. ip nat pool d. ip nat inside pool e. ip nat outside pool Answer: c 12 PIX stands for what? a. Protocol interchange b. Cisco Private Internet c. Private Internet Exchange d. Public Internet Exchange Answer: c
- 481. 556 Appendix A: Answers to Quiz Questions 13 To define how a PIX will route IP data, what is the correct syntax for a PIX 520? a. ip route b. route c. ip route enable d. default-network Answer: b A PIX can run RIP or be configured for static routing; a default route is typically required so that end-user data can be sent to the Internet, for example. 14 What is the alias command’s function on a PIX firewall? a. To define a local host name b. To define the DNS server c. Used in NAT environments where one IP address is translated into another. d. Only applicable to Cisco IOS Answer: c The PIX alias command is used for NAT configurations. The alias command translates one IP address into another address. For example, one private network might be using unregistered IP address space, and to allow users access to outside address space, the alias command is used. This command is applied differently on a Cisco IOS router. 15 CBAC stands for what? a. CBAC is not a valid term b. Cisco Business architectural centre c. Context-based Access Control d. Context-based Accelerated controller e. Content-based arch. Centre Answer: c
- 482. Chapter 7 Q & A Answers 557 16 What is IKE used to accomplish? a. NAT translations b. Ensures that data is not sourced by the right sources c. Ensures that data is not sourced by the wrong sources d. No use e. Both a and c Answer: c Internet Key Exchange (IKE) allows a network confidentially from unauthorized sources. 17 To create a simple VPN tunnel (unencrypted) between two sites, what must you do on a Cisco router? a. Create a GRE tunnel b. Create a routing map c. Nothing, use a PIX d. Create an IPSec tunnel Answer: a A simple VPN tunnel requires a generic routing encapsulation (GRE) tunnel between two Cisco routers. Chapter 7 Q & A Answers 1 What does the term DMZ refer to? Answer: The DMZ, or demilitarized zone, is defined as an isolated part of the network that is easily accessible to hosts on the outside (Internet, for example). 2 What is the perimeter router’s function in a DMZ? Answer: The perimeter router sits between the DMZ and the public domain. It is typically a high performance router or routers that perform a number of duties, including the following: • Access lists to ensure access to IP is restricted • Restrictions to TCP services • Restrictions on what applications can be run • Routing protocols (typically, BGP)
- 483. 558 Appendix A: Answers to Quiz Questions 3 What two main transport layer protocols do extended access lists filter traffic through? Answer: Extended access lists filter both TCP and UDP transport layer services. 4 Which of the following is not a TCP service? a. Ident b. ftp c. pop3 d. pop2 e. echo Answer: e Echo is part of the UDP protocol suite. Ident, ftp, and pop2/pop3 are TCP services. 5 Name five UDP services that can be filtered with an extended access-list. Answer: Cisco IOS can filter a number of UDP services, including the following: • biff—Biff (mail notification, comsat, 512) • bootpc—Bootstrap Protocol (BOOTP) client (68) • bootps—Bootstrap Protocol (BOOTP) server (67) • discard—Discard (9) • dnsix—DNSIX security protocol auditing (195) • domain—Domain Name Service (DNS, 53) • echo—Echo (7) • isakmp—Internet Security Association and Key Management Protocol (500) • mobile-ip—Mobile IP registration (434) • nameserver—IEN116 name service (obsolete, 42) • netbios-dgm—NetBIOS datagram service (138) • netbios-ns—NetBIOS name service (137) • netbios-ss—NetBIOS session service (139) • ntp—Network Time Protocol (123) • pim-auto-rp—PIM Auto-RP (496) • rip—Routing Information Protocol (router, in.routed, 520) • snmp—Simple Network Management Protocol (161) • snmptrap—SNMP traps (162) • sunrpc—Sun Remote Procedure Call (111)
- 484. Chapter 7 Q & A Answers 559 • syslog—System Logger (514) • tacacs—TAC Access Control System (49) • talk—Talk (517) • tftp—Trivial File Transfer Protocol (69) • time—Time (37) • who—Who service (rwho, 513) • xdmcp—X Display Manager Control Protocol (177) 6 What RFC defines NAT? Answer: Network Address Translation (NAT) is defined in RFC 1631. 7 In NAT, what is the inside local address used for? Answer: The inside local address refers to the IP address that is assigned to a host on the internal network, that is, the logical address that is not being advertised to the Internet. A local administrator generally assigns this address. This address is NOT a legitimate Internet address. 8 What does the IOS command ip nat inside source list accomplish? Answer: It defines the addresses that will be allowed to access the Internet. This command enables the network address translation of the inside source addresses. The “list” keyword helps define the access list to be used for determining the source addresses. 9 What are the four possible NAT translations on a Cisco IOS router? Answer: The four NAT translation versions are as follows: • Static NAT—Maps an unregistered IP address to a registered IP address on a one-to-one basis. • Dynamic NAT—Maps an unregistered IP address to a registered IP address from a group of registered IP addresses. • Overloading—A form of dynamic NAT that maps multiple unregistered IP addresses to a single registered IP address using different ports. Known also as Port Address Translation (PAT), single address NAT, or port-level multi- plexed NAT. • Overlapping—When the IP addresses used on your internal network are registered IP addresses in use on another network, the router must maintain a lookup table of these addresses so that it can intercept them and replace them with registered unique IP addresses.
- 485. 560 Appendix A: Answers to Quiz Questions 10 How many connections can be translated with a PIX firewall for the following RAM configurations: 16 MB, 32MB, or 128MB? Answer: You can support up to 260,000 connections with 128MB, 16MB can support up to 32,768 connections, and 32MB of memory can support up to 65,536 connections. 11 When the alias command is applied to a PIX, what does it accomplish? Answer: The alias command translates one address into another, and is used for translating unregistered IP addresses in a NAT environment. 12 What security features does the Cisco IOS Firewall feature set allow a network administrator to accomplish? Answer: The Cisco IOS features set consists of the following: • Context-based Access Control (CBAC) provides internal users secure, per- application-based access control for all traffic across perimeters, such as between private enterprise networks and the Internet. • Java blocking protects against unidentified, malicious Java applets. • Denial-of-service detection and prevention defends and protects router resources against common attacks, checking packet headers and dropping suspicious packets. • Audit trail details transactions, recording time stamp, source host, destination host, ports, duration, and total number of bytes transmitted. • Real-time alerts log alerts in case of denial-of-service attacks or other preconfigured conditions. 13 What does CBAC stand for? Answer: Context-based Access Control 14 Name the eight possible steps to take when configuring CBAC. Answer: To configure CBAC, the following tasks are required or optional: • Pick an internal or external interface. (Required) • Configure IP access lists at the interface. (Required) • Configure global timeouts and thresholds. (Required) • Define an inspection rule. (Required) • Apply the inspection rule to an interface. (Required) • Configure logging and audit trail. (Required) • Follow other guidelines for configuring a firewall. (Required) • Verify CBAC. (Optional)
- 486. Chapter 8 “Do I Know This Already?” Quiz Answers 561 15 What is a virtual private network? Answer: A virtual private network (VPN) enables IP traffic to travel securely over a public TCP/IP network by encrypting all traffic from one network to another. A VPN uses tunneling to encrypt all information at the IP level. Chapter 8 “Do I Know This Already?” Quiz Answers 1 A remote user tries logging into a remote network but fails after three additional tries and is disconnected. What useful information should the network administrator gather? (Select the best two answers.) a. Username b. Invalid password c. Invalid username d. Valid username Answer: b and c Network administrators need the invalid username (because it is not an allowable username) and the invalid password used to see if the intruder is using a text-based algorithm to generate passwords. 2 What is the first step that should be implemented in securing any network? a. Create a database of secure passwords. b. Create the IP address scheme. c. Run NetRanger or NetSonar. d. Define a security policy. e. Configure access lists on all routers. Answer: d The first step in securing any network must be to define the security policy.
- 487. 562 Appendix A: Answers to Quiz Questions 3 What primary security method can be designed and deployed to secure and protect any IP network after an attack has been documented? a. Security policy b. IP policy c. Countermeasures d. Measurement e. Logging passwords Answer: c Countermeasures should be in placed in every IP network. For example, back up sensitive data or application software and apply all the required patches. 4 A security administrator notices that a log file stored on a local router has increased in size from 32 k to 64 k in a matter of seconds. What should the network administrator do? a. Increase the buffer to 64 k. b. Decrease the buffer to 16 k. c. Log the event as suspicious and notify the incident response team. d. Nothing, this is normal. e. Both a and b are correct. Answer: c Any log file that increases (more data to view) or decreases (for example, cleared by the intruder to hide his actions) should be regarded as suspicious activity. 5 What is the primary responsibility of CERT/CC? a. Define access lists for use on routers b. Set security standards c. Coordinate attacks on secure networks d. Maintain a security standard for networks e. Nothing to do with security Answer: d CERT/CC’s primarily responsibility is to aid in the security of any public network; go to www.cert.org for more details.
- 488. Chapter 8 “Do I Know This Already?” Quiz Answers 563 6 Who can use network scanners and probes? (Select the best two answers.) a. Intruders b. Security managers c. End users d. Cable service providers Answer: a and b Network scanners are used by intruders just as network administrators use them. 7 What is a bastion host? a. Firewall device supported by Cisco only b. Network’s last line of defense c. Network’s first line of defense d. IP host device designed to route IP packets Answer: c Bastion hosts are typically the first line of defense. Sometimes, they are sacrificed because they are typically public domain servers and can be quickly restored using backup methods. 8 A TCP SYN attack is what type of attack? a. ICMP b. DoS c. Telnet/Kerberos attack d. Ping attack only Answer: b A TCP SYN attack is a form of denial-of-service attack.
- 489. 564 Appendix A: Answers to Quiz Questions 9 When an intruder sends a large amount of ICMP echo (ping) traffic using IP broadcasts, this type of DoS attack is known as what? a. Bastion b. Land.C c. Man in the middle d. Smurf e. Ping of death Answer: d A Smurf attack sends large ICMP or ping requests via a broadcast address, ensuring that all devices on the remote network respond and enabling the intruder to list the IP address that is connected to the network for further DOS-based attacks. 10 What kind of attack sends a large ICMP echo request packet with the intent of overflowing the input buffers of the destination machine and causing it to crash? a. Ping of death b. Smurf c. Land.C d. Man in the middle e. Birthday attack Answer: a A ping of death sends a large number of ICMP echo request packets causing the end device to overflow, and can cause a remote server to stop functioning for legitimate requests. 11 In the context of intrusion detection, what is an exploit signature? a. DoS attack b. An attack that is recognized and detected on the network c. The same as a Smurf attack d. The same as a man in the middle attack Answer: b An exploit signature is an attack that is readily detected.
- 490. Chapter 8 Q & A Answers 565 12 To stop spam e-mail from overwhelming an e-mail server, what step can you take? a. Ask the ISP for help. b. Nothing, because spam e-mail is too difficult to stop to be worth the effort. c. Install an intrusion detection system that has a signature for spam e-mail. d. Nothing, because the client software takes care of this. e. Change the IOS code. f. Configure the bastion host to stop spam e-mail. Answer: c Spam e-mail can be controlled with an IDS server. Chapter 8 Q & A Answers 1 Define four reasons networks should be secured. Answer: IP networks must provide a network security policy for the following reasons: Inherent technology weaknesses—All network devices and operating systems have inherent vulnerabilities. Configuration weaknesses—Common configuration mistakes can be exploited to open weaknesses. Security policy vulnerabilities—The lack of security policies can lead to vulnerabilities, such as password security. Outside/inside intruders—There are always internal and external people wanting to exploit network resources and retrieve sensitive data. 2 What is the function of the CERT/CC organization, and what are its primary objectives? Answer: The CERT Coordination Center (CERT/CC) is a center of Internet security expertise, located at the Software Engineering Institute, a U.S. federally funded research and development center operated by Carnegie Mellon University. CERT/CC provides information ranging from protecting your networks from potential problems, to reacting to current problems, to predicting and preparing for future problems. Work involves handling computer security incidents and vulnerabilities, publishing security alerts, researching long-term changes in networked systems, developing information, and even providing training to help you improve security. CERT/CC does not concern itself with the individual or where the intruder is physically located, but ideally tries to restore and prevent similar attacks in the future. CERT/CC is regarded as the industry leader in security concerns.
- 491. 566 Appendix A: Answers to Quiz Questions 3 What are the primary steps completed by incident response teams? Answer: Incident responses teams do the following: Verify the incident. Determine the magnitude of the incident (hosts affected and how many). Assess the damage (for example, if public servers have been modified). Gather and protect the evidence. 4 Name common methods used by intruders to disrupt a secure network. Answer: Intruders can use the following methods (and many more): Session hijacking—The intruder defines himself with a valid IP address after a session has been established to the real IP address by spoofing IP packets and manipulating the sequence number in an IP packet. Rerouting—Packets from one source are routed to an intruder source. Routing updates are altered to send IP packets to an incorrect destination, allowing the intruder to read and use the IP data inappropriately. Denial-of-service (DoS) attacks—A service attack that is used in an attempt to deny legitimate users access to a network they have full rights to. Probes and scans. Malicious code. 5 In security, what is session hijacking? Answer: Session hijacking is where the intruder defines himself with a valid IP address after a session has been established to the real IP address by spoofing IP packets and manipulating the sequence number in an IP packet. 6 In security terms, what is a man in the middle attack? Answer: Just as with packet sniffers and IP spoofing attacks, a brute-force password attack can provide access to accounts that can be used to modify critical network files and services. An example that compromises your network’s integrity is an attacker modifying your network’s routing tables. By doing so, the attacker ensures that all network packets are routed to him before they are transmitted to their final destination. In such a case, an attacker can monitor all network traffic, effectively becoming a man in the middle.
- 492. Chapter 8 Q & A Answers 567 7 What is a Signature Engine? Answer: A Signature Engine is a component designed to support many signatures in a certain category. An engine is composed of a parser and an inspector. Each engine has a set of legal parameters that have allowable ranges or sets of values. Exploit signatures are an identifiable pattern of attack. 8 What is social engineering? Answer: Social engineering is the act of tricking or coercing employees into providing information, such as usernames or mail user identifications and even passwords. First-level phone support personnel are typically called by intruders pretending to work for the company to gain valuable information. 9 Describe a ping of death attack. Answer: A ping of death occurs when a large number of ICMP echo request packets cause the end device to overflow. For example, a ping of death can cause a remote server to stop functioning for legitimate requests. 10 What is a Land.C attack? Answer: A Land.C attack is a program designed to send TCP SYN packets (TCP SYN is used in the TCP connection phase) that specify the target’s host address as both source and destination. This program can use TCP port 113 or 139 (source/ destination), which can also cause a system to stop functioning. 11 What does the following IOS code accomplish on a Cisco IOS router? no service udp-small-servers no service tcp-small-servers Answer: These commands disable the minor TCP/UDP servers. When the minor TCP/IP servers are disabled, access to the Echo, Discard, Chargen, and Daytime ports causes the Cisco IOS Software to send a TCP Reset packet to the sender and discard the original incoming packet. When these commands are entered in global configuration, they do not display when you view the configuration (show running- config or write terminal) because the default is to disable TCP/UDP small servers. Unlike Cisco Switches, Cisco IOS Software does not display default configuration. 12 What is the secret password for the following IOS configuration? enable secret %$@$%&^$@*$^*@$^* enable pass cisco Answer: Secret passwords are encrypted using the MD5 hashing algorithm, so you cannot decipher the secret password, which overrides the enable password. 13 What is the purpose of the command service sequence-numbers? Answer: Essentially, this command enables your syslog entries to be numbered and ensures that they are not tampered with by external sources.
- 494. APPENDIX B Study Tips for CCIE Security Examinations This appendix describes some study tips and options for you to consider while preparing for the CCIE Security written and lab examinations. CCIE is regarded as the most sought-after certification in the industry today; more and more vendors are devising their own certification programs and trying to catch up to the industry- leading Cisco Systems. Working in the CCIE program, I have seen many changes and challenges facing potential CCIEs every day for the past two years. As of August 22, 2002, there were approximately 9000 CCIEs, and the number is growing rapidly. Of the 9000 CCIEs, approximately 110 hold more than one CCIE certification. The majority of CCIEs are located in Europe and North America. Before you decide to take this step, you need to be aware of the challenges in front of you. You cannot hope to become a CCIE by simply buying a book or a series of books. Hands- on experience is required, and at least two years of internetworking experience is critical; and even then, you must fully prepare for the difficult examinations. The current three varieties of CCIE certification follow: • CCIE Routing and Switching (released 1993) • CCIE Security (released August 2001) • CCIE Communications and Services (released August 2001) This discussion concentrates on the CCIE Security certification. The CCIE Security examination is one examination you should consider tackling, especially in today’s climate of Internet firewall frailty and demand for security experts. NOTE For more information on the Security track, see the following: www.cisco.com/en/US/learning/le3/le2/le23/le476/learning_certification_ type_home.html Recently, four CCIE tracks were retired: ISP Dial, SNA, Design, and WAN Switching.
- 495. 570 Appendix B: Study Tips for CCIE Security Examinations Steps Required to Achieve CCIE Security Certification The CCIE Security certification requires a candidate to pass two exams: • A 2-hour, computer-based written exam (#350-018) consisting of 100 questions. The pass mark is approximately 70 percent, but varies according to statistics and could float between 65 and 75 percent. This book is designed to help prepare you for this written exam. • An 8-hour lab examination. The passing score is set at 80 percent. Historically, the lab examination was a full 2-day lab; that changed October 1, 2001. All CCIE lab exam versions are monitored closely and adapted where necessary to conform to the CCIE program standards, which are not publicly available. This book contains supplemental material intended to help you prepare for the lab exam, but that is not the focus of this book. The following URL provides a breakdown of CCIE numbers and geographic locations: www.cisco.com/en/US/learning/le3/le11/learning_ccie_population.html CCIE Security Written Exam The CCIE Security written exam uses the typical certification test format of asking multiple- choice questions with one or more correct answers per question. What makes some of the questions more difficult is that more than five answer choices are listed on some questions. This reduces the power of eliminating answers and choosing from those remaining. However, the number of required answers is given for each question. You might be required to give only one answer or select a couple of correct answers. Attempt to answer every question to give you the best chance of passing, even if you have to guess. After completing the test, you will be given a percentage for each section. The following are the sections you will be scored in: • Security Protocols • Operating Systems • Application Protocols • General Networking • Security Technologies • Cisco Security Applications • Security General • Cisco General
- 496. CCIE Security Written Exam 571 If you do not receive a passing score, compare your results with Table 1-1 to identify the areas you need to concentrate on for your next attempt. You will also be given the passing mark, your score, and your grade. The grade is either a pass or fail. The examination is similar to other Cisco certifications, albeit it is a little more difficult with many more in-depth questions. You can view some sample questions from the similarly formatted CCIE Routing and Switching written exam at the following location (there are currently no available security questions): www.cisco.com/warp/public/625/ccie/certifications/sample_routing.html The CCIE Security written exam requires test-taking skills that many of us learned in high school or college. This section is a refresher for many and important for all. The first thing to focus on is time management during the test. The CCIE exam allows 120 minutes to complete the test. You have 100 questions, so if you allow 1 minute per question and 20 minutes to review your answers, you will be doing well. Some questions require more time, so you can mark and skip them if you want and complete them later. Be sure before moving on to the next question that the application on the testing device permits a review of questions; Cisco can change this at any time. Remember that a wrong answer incurs no extra penalty, so answer all the questions. Another advantage of marking difficult questions and returning to them at the end is that the answer for a previously asked question will often appear in a later question. I have also found that at times when I can’t remember an answer that I should know, my memory is later refreshed by another question. Remember to just mark questions that you can’t answer and come back to them at the end. Read every question and all the possible answers carefully. The CCIE Security written exam has many questions that are designed to be tricky, so they require careful examination of the syntax. Many of the questions refer to exact commands required to implement a function on a router. It is important to know the different syntax and to recognize small differences in commands. This book has similarly formatted questions in each chapter and in the sample questions on the CD-ROM. Go through these questions, study areas of weakness, and go through the questions again to ensure your understanding of a subject. Make sure you read every answer before choosing one. One answer might sound great; however, another answer could be more correct than the first. The fact that on these exams one answer can be more or less correct than another is a concept you should keep in mind when taking any Cisco exam. In addition, saying questions out loud or writing them down on your scrap paper might help you understand the question easier than viewing it on a computer screen.
- 497. 572 Appendix B: Study Tips for CCIE Security Examinations NOTE Occasionally, Cisco announces a beta trial for the written exams, and if you book the test, you pay only a small fee compared to the standard fee of approximately U.S.$250. The following link has more information: www.cisco.com/en/US/learning/le3/le11/learning_beta_certifcation_exams_list.html Decoding Ambiguity Cisco exams have a reputation for including questions that can be difficult to interpret, confusing, or ambiguous. In my experience with numerous exams, consider this reputation to be completely justified. The Cisco exams are deliberately tough. The only way to beat Cisco at its own game is to be prepared. You’ll discover that many exam questions test your knowledge of things that are not directly related to the issue that a question raises. This means that the answers you must choose from—even incorrect ones—are just as much a part of the skill assessment as the question itself. If you don’t know something about most aspects of the CCIE Security written exam topics, you might not be able to eliminate obvious wrong answers. In other words, the more you know about Cisco IOS Software and securing Cisco internetworks, the easier it will be for you to tell a right answer from a wrong one. Questions often give away their answers, but you have to be Sherlock Holmes to see the clues. Often, subtle hints appear in the question text in such a way that they seem almost irrelevant to the situation. You must realize that each question is a test unto itself, and you must inspect and successfully navigate each question to pass the exam. Look for small clues, such as access list modifications, problem isolation specifics (such as which layers of the OSI model are not functioning correctly), and invalid Cisco IOS commands. Little things like these can point to the right answer if properly understood; if missed, they can leave you facing a blind guess. Another trick is to watch out for keywords, such as not or choose the best; these words will define the required answer. If you miss keywords, your answer will be correct in your mind but might not be the correct answer. Read questions out loud or write them down to ensure you identify keywords and fully understand what the question is asking. For questions requiring more than one answer, be sure to view how many answers are required and remove the obvious choices before making your selection. These questions are frequently ambiguous, and you need to be on your guard. Another common difficulty with certification exams is vocabulary. Be sure to brush up on the key internetworking terms presented in this guide. You may also want to read through the Terms and Acronyms on the following Cisco website: www.cisco.com/univercd/cc/td/doc/cisintwk/ita/index.htm The test questions appear in random order, and many elements or issues that receive mention in one question might also crop up in other questions. It’s not uncommon to find that an incorrect
- 498. CCIE Security Written Exam 573 answer to one question is the correct answer to another, or vice versa. Take the time to read every answer to each question, even if you recognize the correct answer to a question immediately. Because you’re taking a fixed-length test, you can revisit any question as many times as you like. If you’re uncertain of the answer to a question, check the box that’s provided to mark it for easy return later on. You should also mark questions you think might offer information that you can use to answer other questions. Candidates usually mark somewhere between 25 and 50 percent of the questions on exams. The testing software is designed to let you mark every question if you choose; use this framework to your advantage. Everything you want to see again should be marked; the testing software can help you return to marked questions quickly and easily. Be sure to check out the latest updates from Cisco because policies like these can change; see the following URL for more details: www.cisco.com/en/US/partner/learning/le3/learning_ccie_written_exam.html The best method to pass any Cisco written exam is to go through each question and answer the questions you are confident with in your first pass and mark the remaining questions. After you complete the 100 questions, review all your marked questions. On your second pass, survey the questions you marked more thoroughly as you begin to answer them systematically and consistently. Try to eliminate the choices that are way off base and make an educated guess with the remaining choices. Continue to mark and ignore the clueless questions, and on pass three, attack the totally clueless ones; by then, you might be able to make a more educated guess from clues in the context of other questions you already answered. If you have time, you can go back and check all your answers. Experience has shown me that your first reaction to a question is typically the best choice unless you see a glaring mistake. Preparing for the Written Exam The best way to prepare for the test—after you study—is to take practice exams until you feel comfortable with your results. This certification guide includes over 300 simulated test questions on the CD-ROM that allow you to take the sample examination (in study and exam simulation modes) as many times as you like until you are comfortable with the test format and your knowledge level. Try to identify subject areas where you are weak and use this book and other resources to study those areas more. Give yourself 120 minutes to take the practice exam, keep yourself on the honor system, and don’t look at text in the book or jump ahead to the answer key. When your time is up or you finish the questions, go back and review your correct and incorrect answers. You learn more by making mistakes in a simulation than from the real examination, which provides little feedback on incorrect answers. Study your incorrect answers very carefully. Practice the three-phase approach I mentioned earlier, or if you have your own strategy, practice this strategy a few times before attempting the real examination.
- 499. 574 Appendix B: Study Tips for CCIE Security Examinations I have attempted to estimate the number of questions that are taken from each subject area to give you an idea of where to focus the majority of your time. Each chapter contains a weighted number of questions to match those on the examination, and similarly, the CD-ROM simulation examinations are weighted, as well. For example, 50 percent of the CD-ROM questions are based on Routing and Switching topics, 50 percent are on Security topics, and so forth to mimic the questions on the real exam. The percentage of questions you get for any topic will vary. The passing score will also vary. If you concentrate on the questions and think clearly, you will not need to worry about the passing score. Typically, the passing range is from 65 to 75 percent depending on the scoring rate for that month. Cisco will not release the passing score. As far as I have discovered, the passing score is static for the Security examination at 70 percent, but don’t be surprised if this changes in the future. Knowing how to recognize correct answers is good, but understanding why incorrect answers are wrong can be equally valuable. I cannot stress how much getting hands-on experience with Cisco routers and switches will help you pass not only the written exam, but also the more difficult lab examination. A small test bed with two Cisco routers and a PC is the best way to learn and reinforce your theoretical knowledge. I strongly recommend it even for the written exam, which, in turn, aids your preparation for the lab examination. Cisco provides a Cisco Documentation CD with every shipment with a wealth of documenta- tion that you can implement on test equipment. The documentation CD is a great study tool. The documentation CD is not provided for the written exam but is provided for the laboratory exam. Understanding how a protocol works is only half of your goal; you need to appreciate how Cisco routers and switches operate when a certain protocol is activated with IOS. Talk to all your colleagues or friends that attempted the written exam and find out what they studied to help them. Of course, all who have taken the exam are bound by the nondisclosure agreement, so you cannot share specific details about exam content, but you can share study tips and habits. Taking the Written Exam On exam-day eve, you should relax and spend a maximum of one hour studying. Don’t sit up all night studying and worrying—if you want to do your best, you need to feel refreshed. Have a good meal, scan your study materials (such as the “Foundation Summary” sections in this book), and get a good night’s sleep. On the day of the exam, eat a well-balanced breakfast and briefly review your study notes. Make sure that you arrive at the testing center at least one hour before your scheduled time. Find a quiet corner to relax and mull over the main exam subjects. When you’re sitting in front of the testing computer, there’s nothing more you can do to increase your knowledge or preparation. Take a deep breath, stretch, and read the first question.
- 500. CCIE Security Written Exam 575 Don’t rush; you have plenty of time to complete each question. Both easy and difficult questions are intermixed throughout the test in random order. Don’t cheat yourself by spending too much time on a hard question early in the test, depriving yourself of the time you need to answer the questions at the end of the test. On a fixed-length test, you can read through the entire test and, before returning to marked questions for a second visit, figure out how much time you have per question. As you answer each question, remove its mark. Continue to review the remaining marked questions until you run out of time or you complete the test. After you complete the exam, your test will be scored immediately. A few moments after you finish, the computer will indicate whether you passed or failed. You Passed! Passing the CCIE Security exam means that you’re ready to take the lab examination. Within 48 to 72 hours, Cisco will be notified of your result. There is no need to fax your result, as was previously required. To set a lab exam date, visit tools.cisco.com/CCIE/Schedule_Lab/jsp/ login.jsp and select the location and examination date you prefer. (Hopefully, seats will be available.) The lab exam is popular, and you might need to wait a month or more for an opening. Some locations have a waiting list of six months or more. For example, the Sydney, Australia CCIE lab is generally not fully booked, and you might get a seat at a time of your choice; in Brussels, Belgium, you might need to wait six months. Make sure you agree to a testing date that you feel comfortable with, and leave yourself plenty of time to study for the rigorous lab exam. After passing the written test, you have one full year to pass the lab examination, so, if necessary, you can study for a few months before taking it. You Failed If you fail the CCIE Security written exam, don’t worry about the result. You can still take advantage of the situation. While the test is fresh in your mind, jot down problem areas on a notepad (the sooner you make notes for yourself the better). Try to remember questions you felt less comfortable with and study those areas before taking the exam again. The CCIE Security written exam is not an easy exam to pass. In fact, this examination ranks among the toughest networking examinations in today’s certification market. If you really want to be a CCIE, a first-attempt failure should not discourage you. A failed attempt should encourage you to invest in some serious study time so that you can pass on your next attempt. A number of candidates have noted that the second attempt is much easier than the first. Remember that the reason Cisco Systems makes the written examination hard is to ensure that you are fully prepared for the challenging lab examination. That’s it for pointers. Here are some frequently asked questions about the written examination followed by some bonus information on the lab examination.
- 501. 576 Appendix B: Study Tips for CCIE Security Examinations FAQs About the CCIE Security Written Exam This section answers some common questions about the written CCIE Security examination. These frequently asked questions should help dispel any confusion surrounding this exam. 1 How many questions are on the CCIE Security written examination? There are 100 questions. All questions are multiple choice. Some questions require a single answer, whereas other questions require more than one answer to earn a point. 2 What is a passing score? Cisco no longer publishes a set passing score for the written examination. Instead, Cisco supplies you with a pass or fail grade. The actual passing score (a percentage) is based on a statistical analysis system that checks the scores of all candidates over three months and adjusts the score needed to pass accordingly. For example, the passing score for one candidate might be 70 percent, but it might be 75 percent for another candidate, depending on what results candidates are attaining. 3 Can I change an answer after working through all the questions? Yes, as long as time remains, you can return to any question. 4 How long is the examination? The exam is two hours long. Make sure you use your time wisely—you want to have an opportunity to answer as many questions as possible. If you find you are spending too long on a single question, mark it and move on. If time permits, you can return to difficult questions later. 5 What happens when I finish the examination? The computer scores your test within minutes and indicates whether you passed or failed. You receive a printed score sheet with a grade for the entire exam and a percentage score for each of the topics. If you fail, you must wait at least 24 hours before retaking the exam. 6 Can I use the Windows calculator during the exam? No. You are not permitted to use any Windows tools. You are supplied with a pencil and some white paper or an erasable sheet. 7 How many times can I retake the written examination? You can retake the exam as many times as you like. 8 What do I do after I pass the written exam? You do not need to fax your test results to your nearest CCIE lab administrator. Visit the following URL to set a lab examination: tools.cisco.com/CCIE/Schedule_Lab/jsp/login.jsp
- 502. CCIE Security Lab Exam 577 9 Where can I find further information about the CCIE Security exam? Cisco provides additional information online: www.cisco.com/en/US/learning/le3/le2/le23/le476/learning_certification_ type_home.html CCIE Security Lab Exam NOTE Although the focus of this book is to prepare you for the CCIE Security written exam only, you can find bonus material, such as this section, that helps start your preparation for the lab exam. Passing the written examination is the easier part of the CCIE Security certification journey. For the lab exam, your life needs to change dramatically, and you need to study on routers full time for at least three to six months. The good news is that the format of the lab examination has changed from two full days to one day. You are no longer required to troubleshoot a network (regarded as the true method to test a CCIE’s ability to restore a network back to full IP con- nectivity); you are now required only to configure a set number of Cisco IOS, PIX, and Catalyst features. Upon entering the lab room, you will already have preconfigured router and switch host names and IP addressing, and the enable password and login commands will all be set on all devices to cisco. After you pass the written exam, you are eligible to sit for the lab examination. You can book your lab examination online: tools.cisco.com/CCIE/Schedule_Lab/jsp/login.jsp The lab examination contains the following devices: • 2600 Series Routers • 3640 Series Routers • 4000/4500 Series Routers (not all labs) • PIX 520 running 5.2 or later • Catalyst 5000 or 3550 Series switches • Cisco ACS running on Windows 2000 server
- 503. 578 Appendix B: Study Tips for CCIE Security Examinations Make sure you practice with and understand these devices. Practice configuring almost every IOS feature and fully understand what each IOS command actually enables, rather than just relying on limited experience with certain commands. Anyone can configure a Cisco router, but the ability to understand the full consequence of any Cisco IOS command is crucial to the CCIE Security lab examination. CCIE Security Lab Exam FAQs The following are some frequently asked questions about the difficult one-day CCIE Security lab examination. 1 When did the lab format change from two days to one day? October 2001. All CCIE certification labs worldwide now test candidates in the one- day format. 2 Where can I take the CCIE Security lab examination? Locations and contact information follow: • San Jose, California Tel: 1-800-829-6387 (select option 2) or 1-919-392-4525 Fax: 1-919-392-0166 E-mail: ccie_ucsa@cisco.com • Chatswood, NSW, Australia (location of this author) Tel: +61 2 8446 6135 Fax: +61 2 8446 8440 E-mail: ccie_apt@cisco.com • Brussels Belgium Tel: +32 2 704-5670 Fax: +32 2 704-6000 E-mail: ccie_emea@cisco.com Over time, you can expect the Security lab examination to be available in other locations worldwide. E-mail ccie-lab@cisco.com if you want to know more details. 3 What is the maximum score and what is a passing score? The total examination is worth 100 points and the passing grade is 80 percent. The passing rate for first attempts is very low, so expect the possibility of taking the examination more than once. Cisco will not release the passing rate.
- 504. CCIE Security Lab Exam 579 4 What if I have a question and cannot find the answer? E-mail your question to ccie-lab@cisco.com. All questions receive a response from the CCIE team within 72 hours. 5 What happens after the exam? You will be escorted outside the lab. You receive an e-mail notification within 24 hours. The e-mail advises you to log on to Cisco’s website (tools.cisco.com/CCIE/ Schedule_Lab/jsp/login.jsp) and login your written exam results, and you will be presented with a breakdown of the main sections and your percentage score in each section. You can fill in a critique regarding your lab experience; be sure to provide all the feedback you have—good or bad. Candidates can receive free lab attempts for valid excuses or lab incompetence. For the price, you want to make sure you have been given every opportunity to pass. 6 Can I use Notepad and Windows calculator? Yes, you can, but you are not permitted to save any files. You can, however, cut and paste to and from Notepad. Calculator is very useful for determining subnets and bit boundaries or converting hexadecimal to decimal. 7 How many times can you take the lab examination? You must allow 30 days between lab attempts. There is no limit on the number of lab attempts, and there are no minimum score requirements. 8 What happens if you pass? In addition to becoming a CCIE, you also gain access to exclusive CCIE chat forums and merchandise, and you receive a CCIE medallion and certificate. Expect these to be mailed to you between 6 and 12 months after your test date. The following URL provides more details on benefits CCIEs can expect: www.cisco.com/en/US/learning/le3/learning_about_recertication.html 9 What happens if I fail? Am I told in which areas I scored poorly? Cisco will not tell you specific areas of weakness; that is left to the candidate to decipher from the brief score report. You can, however, pay a fee (U.S.$250.00) to have your lab routers re-examined for accuracy. Unless you believe your score is close to 80 percent, I strongly recommend you keep studying and put those funds toward another attempt. Even with a regrade, no additional information is provided to you—only a brief score report by e-mail and your new grade (pass or fail).
- 505. 580 Appendix B: Study Tips for CCIE Security Examinations 10 What materials can you bring into the lab? You are permitted to bring only necessary medication and a dictionary. No other materials are permitted. Cisco provides refreshments at all CCIE lab sites. Lunch is also provided during a lunch break (30 minutes). Lunch is mandatory and CCIE staff escort you. 11 What is the proctor’s role? You can seek clarification from a proctor if you do not understand a question or the objective of a question. The proctor cannot provide answers but can ensure that you understand the question. The proctor can also make any changes required in case of network hardware failures or examination mistakes. The proctor is there to ensure that you have the best possible chance of success and should not hinder your ability to pass the test. If you feel otherwise, you can e-mail your concerns to ccie-lab@cisco.com. The CCIE program manager’s core responsibility is the welfare of the candidates, and you never know, your case might warrant a free future lab. 12 Where can I find out more about CCIE and all the different certification tracks? The following URL provides information about the CCIE tracks: www.cisco.com/en/US/learning/le3/le2/le23/learning_certification_level_home.html 13 How often do you need to recertify? You must recertify every two years to maintain your CCIE status; otherwise, your CCIE status will be changed from active to inactive. An inactive CCIE means you cannot purchase CCIE merchanise or particiapte in the CCIE forum. To view your CCIE status, visit the following URL: www.cisco.com/en/US/learning/le3/le11/learning_ccie_online_verification_ tool_launch.html 14 What examinations or alternative methods can I take to recertify my CCIE? Currently, you can use a couple different methods to recertify your CCIE: • You can take any of a number of different written examinations. • You can achieve a CCIE certification from a track you do not currently possess. For more information on recertification, visit www.cisco.com/en/US/learning/le3/ learning_about_recertication.html.
- 508. INDEX Symbols adaptive cut-through switching, 30 address classes, 36 .rhosts file (UNIX), 290 adjacencies, 67 | (pipe), 174 administrative distances, 56-57 agents (SNMP), 123 Aggregator attribute (BGP), 78 Numerics Aggressive mode (IKE), 246 AH (Authentication Header), 244-246 3DES (Data Encryption Standard), 238 alias command, 167 10Base2, 28 allocating IP addresses, InterNIC, 325 10Base5, 28 ambiguous test questions, decoding, 572-573 10BaseT, 28 application layer (OSI model), 25 100BaseT, 28 applications 802.1Q, 33 NetRanger, 300 1000 GE, 28 Director, 302 sensors, 300 supporting platforms, 301 A typical network placement, 300 TFTP, 113 AAA (authentication, authorization and applying access lists to interfaces, 185-187 accounting), 208-209 areas, 67 accounting, 211-212 arguments (UNIX commands), 286 authentication, 210 ARP (Address Resolution Protocol), 45-46 authorization, 210-211 AS (autonomous system), 67 ABRs (Area Border Routers), 68 AS_Path attribute (BGP), 77 access lists, 250 ASA (Adaptive Security Algorithm), 330 extended, 187-189 ASBRs (autonomous system boundary routers), 68 filtering TCP services, 222-224 asynchronous communications, 84-85 IP packet debugging, 171-172 Atomic Aggregate attribute (BGP), 78 standard, 182-187 attacks wildcard masks, 184 birthday attacks, 372 accessing Cisco routers, 179 chargen, 371 accounting, 208, 211-212 CPU-intensive, 371 ACKs (acknowledgments), 63 DDoS, 371 ACS (Cisco Secure Access Control Server). DNS poisoning, 371 See Cisco Secure DoS, 370-372 Active Directory, 133 e-mail, 371 Active FTP, 115-117 incident response teams, 367
- 509. 600 attacks Land.C, 371 birthday attacks, 372 man in the middle, 372 blocking state (spanning tree), 31 methods of, 369 bootstrap program, 153 motivation for, 365 BPDUs (Bridge Protocol Data Units), 31 ping of death, 371 BRI (Basic Rate Interface), 80 sacrificial hosts, 370 bridging, 28 smurf, 372 port states, 31 spoof attacks, 372 transparent, 30 TCP SYN flood, 371 broadcast domains, 30 teardrop, 371 broadcasting, 292 UDP bombs, 371 browsing, 291 attrib command (DOS), 285 attributes BGP, 77-78 C of RADIUS, 214 authentication, 208-210 calculating hosts per subnet, 37-38 HTTP, 119 CAM tables, 29 Kerberos, 225 CBAC (Content-Based Access Control), 345 method lists, 217 audit trail messages, enabling, 451 on TACACAS+ servers, 219 configuring, 346-347 PPP, 82 cd command (DOS), 284 authoritative time sources cd command (UNIX), 284 configuring, 130-131 CERT/CC (Computer Emergency Response Team stratum, 128-129 Coordination Center), 366 authorization, 209-211 certification exam on TACACAS+ servers, 219-220 objectives, 4-7 preparing for, 3, 7-8 characteristics B of RIP, 57-58 of RIPv1, 58 backup domain controllers, 290 of RIPv2, 59 bastion hosts, 370 chargen attacks, 371 BECN (backward explicit congestion chkdsk command (DOS), 284 notification), 83 chmod command (UNIX), 289 BGP (Border Gateway Protocol), 76 CIDR (classless interdomain routing), 39 attributes, 77-78 Cisco IDS (Intrusion Detection System), 373. characteristics, 77 See also NetRanger configuring, 79 sensors, 373 messages, 76 Signature Engines, 373-374 supported products, 373
- 510. components of Security Wheel 601 Cisco IOS DOS configuration files, saving, 158 attrib, 285 firewall features, 344-345 ip helper-address, 292 intrusion prevention methods ipconfig, 295-296 core dumps, 379-380 route, 296 disabling default services, 378 ip host, 110 disabling DHCP, 377 ip http authentication, 119 disabling TCP/UDP small servers, 376 ip route-cache, 168 enabling sequence numbering, 378 ip subnet-zero, 38 enabling TCP intercept, 379 logging console debug, 168 Nagle algorithm, 375-376 service password-encryption, 181 modes of operation, 157 service tcp-keepalives-in, 376 password recovery, 174-179 set vlan, 30 Cisco Product Security Incident Response Team shortcuts, creating, 167 website, 367 show accounting, 211-212 Cisco Secure, 297, 299 show debugging, 163 AAA features, 298 show interface, 156 features, 297 show interfaces, 163-165 test topics, 297 show ip access-lists, 163 Cisco Secure Scanner, 302-304 show ip arp, 46 Cisco Security Manager, 299 show ip route, 55-56, 162-163 Cisco Security Wheel, 304 show logging, 166 Cisco TFTP, 113 show process, 153 classes of IP addresses, 36 show route-map, 166 classful addressing, 40 show startup-config, 178 classful routing protocols, 40 show version, 155-156, 166 clock sources, NTP configuration, 128-131 SMTP, 127-128 Cluster-List attribute (BGP), 78 snmp-server enable traps config, 124 snmp-server host, 124-126 collisions, jam signals, 27 undebug all, 163 command structure, UNIX, 285-287 UNIX, correlated DOS commands, 284-285 commands community access strings, configuring on Cisco | (pipe) modifier, 174 routers, 121 alias, 167 Community attribute (BGP), 78 copy running-config startup-config, 158 comparing copy tftp flash, 114 preshared keys and manual keys, 255 debug all, 171 RADIUS and TACACS+, 224-225 components of Security Wheel, 304
- 511. 602 configuration files configuration files CPU, 152 loading, 158 attacks, 371 saving, 158 creating Configuration mode (IOS), 157 command shortcuts, 167 configuration registers, 154-156 extended access lists, 187-189 modifying, 177 standard access lists, 182-187 configuring VLANs, 30 BGP, 79 credentials, 227 CBAC, 346-347 crypto map entries, 253 Dynamic NAT, 326 cryptography HSRP, 50-51 key exchange management, 246 IKE, 252-259 IKE, 247-259 Kerberos, 228-229 PKI, 348 Nagle algorithm, 375 CSACS (Cisco Secure Access Control Server), 218 NTP time sources, 128-131 CSMA/CD (carrier sense multiple access collision OSPF detection), 27 in a single area, 66, 69 CSPM (Cisco Secure Policy Manager), 299 in multiple areas, 69-70 cut through switching, 30 PIX, 332-337 RADIUS, 215-217 RIP, 59-61 D SGBP, 85 SNMP support on Cisco routers, 124 DATA command (SMTP), 128 TACACAS+, 220-223 data encryption VPDNs, 231-235 3DES, 238 VPNs, 350-351 DES, 237-238 connectionless protocols, 23 Diffie-Hellman, 240-241 connection-oriented protocols, 23 DSS, 238-239 TCP, 40 IPSec, 242 header format, 41 AH, 244-246 packets, 41-42 ESP, 243-244 Telnet requests, 42, 45 MD5, 239-240 copy command (DOS), 284 principles of, 235-237 copy running-config startup-config commands, 158 data link layer (OSI model), 22 copy tftp flash command, 114 data manipulation, 369 copying IOS images from TFTP servers, 114 DDOS (Distributed Denial Of Service) attacks, 371 core dumps, performing, 379-380 debug all command, 171 cp command (UNIX), 284 debug commands, 168-174 options, 169-170
- 512. enabling 603 debugging, turning off, 163 distance vector protocols default services, disabling, 378 loop avoidance techniques, 59 defining RIP, 57-59 HTTP port number, 120 configuring, 59-61 IP address names, 110 DLCIs (data-link connection identifiers), 83 TFTP download directory, 114 DMZ (demilitarized zone), 320 del/erase command (DOS), 284 DNS (Domain Naming System), 110-111 deploying NAT, 325 disabling lookup on Cisco routers, 112 DES (Data Encryption Standard), 237-238 enabling lookup on Cisco routers, 112 development DNS poisoning, 371 of Ethernet, 27 domains, 290 of OSI reference model, 21 trust relationships, 294 development of UNIX operating system, 284 trusted domains, 292 devices domains (Windows NT), scalability, 292 asynchronous communication, 84-85 DOS commands broadcast domains, 30 attrib, 285 broadcasting, 292 correlated UNIX commands, 284-285 firewalls, 320 ipconfig, 295-296 VLANs, creating, 30 route, 296 Df command (UNIX), 284 DoS (Denial of Service) attacks, 370-372 DHCP (Dynamic Host Configuration Protocol), DRs (Designated Router), 68 47, 292 election process, disabling, 75 disabling, 377 DSS (Data Signature Standard), 238-239, 348 Diffie-Hellman protocol, 240-241 dynamic crypto map entries, 254 dir command (DOS), 284 Dynamic NAT, configuring, 326-327 directories, 289 directories (UNIX), 289-290 disabled state (spanning tree), 31 E disabling default services, 378 EBGP (external BGP), 78 DHCP, 377 EIGRP (Enhanced IGRP), 62-63 DNS lookup on Cisco routers, 112 example configuration, 64-66 TCP/UDP small servers, 376 election process (DRs), disabling, 75 Telnet login password, 113 e-mail displaying attacks, 371 configured policy routes, 166 SMTP, 127-128 router home page, 118 enable passwords, setting, 180 routing tables, 55-56 enabling system log, 166 DNS lookup on Cisco routers, 112 FastEther Channel, 31
- 513. 604 enabling HSRP, 49 Nagle algorithm, 376 F portfast on Cisco switches, 31 FAQs regarding exam, 576-580 sequence numbering, 378 FC (feasibility condition), 63 TCP intercept, 379 feasible distance, 63 encapsulation, 26 features HDLC, 80 of RADIUS, 215 LCP, 82 of TACACAS+ servers, 220 PPP, 81 FEC (FastEther Channel), 31 encrypting passwords, 181 FECN (forward explicit congestion notification), 83 encryption technologies, 235 fields 3DES, 238 of IP packets, 34-35 DES, 237-238 of show ip route command output, 56 Diffie-Hellman, 240-241 of TCP packets, 41-42 DSS, 238-239 file systems IPSec, 242 NTFS, 293 AH, 244-246 UNIX, 289 ESP, 243-244 directories, 289-290 MD5, 239-240 file attributes, modifying, 285 principles of, 235-237 filtering TCP services, 322-324 ESP (Encapsulation Security Payload), 243-244 firewalls, 320 establishing Telnet connections, 179 Cisco IOS features, 344-345 Ethernet CSPM, 299 bridge port states, 31 PIX, 328 CSMA/CD, 27 commands, 339-341 FEC, 31 configuring, 332-337 intefaces, states of, 165 DMZs, 330 media specification, 27-28 stateful packet screening, 330-331 spanning tree, 30 static routing, 337-338 exam flags FAQs, 576 chmod command, 289 objectives, 4-7 UNIX commands, 286 preparing for, 3, 7-8, 575 Flags field (TCP packets), 42 study tips, 569-570 Flash memory, 151 example configurations, EIGRP, 64-66 forwarding state (spanning tree), 31 extended access lists, 187-189 Frame Relay, 83 options, 188-189 frames, 22 external links, 68 BPDUs, 31 framing ISDN, 80
- 514. IOS images 605 FTP (File Transfer Protocol), 53 hybrid routing protocols, EIGRP, 62-63 Active mode, 115-117 configuration example, 64-66 Passive mode, 117-118 functionality of NetBIOS, 291 I G IBGP (internal BGP), 78 ICMP (Internet Control Message Protocol), 52-53 gateways, HSRP, 47 IDSs (intrusion detection systems), 372 configuring, 50-51 Cisco IDS enabling, 49 Signature Engines, 373-374 generating keepalive packets, 376 supported products, 373 global domain model, 293 NetRanger, 300 global groups, 294 Director, 302 gratuitous ARP, 46 sensors, 300 grep command (UNIX), 287 supporting platforms, 301 typical network placement, 300 IETF (Internet Engineering Task Force) H website, 368 ifconfig command (UNIX), 287 hashing algorithms, 238-239 IKE (InternetKey Exchange), 246 MD5, 239-240 configuring, 252-259 SHA, 239-240 phase I, 247 HDLC, (High Level Data Link Control) 80 phase II, 248-252 Hello packets incident response teams, 367 EIGRP, 63 inform requests (SNMP), 122 OSPF, 67 Initial configuration mode (IOS), 157 HELO command (SMTP), 127 inside global addresses, 324 help command (DOS), 284 inside local addresses, 324 hiding secret passwords, 181 instances, 227 hijacking, 369 Interface configuration mode (IOS), 157 holdtime, 63 interfaces, 156 host IDSs, 372 access lists, applying, 185-187 hosts per subnet, calculating, 37-38 Ethernet states, 165 HSRP (Hot Standby Routing Protocol), 47 Internet Domain Survey website, 368 configuring, 50-51 Internet newsgroups, 368 enabling, 49 InterNic, 325 HTTP (Hypertext Transfer Protocol), 118 intruders, methods of attack, 369 defining port number, 120 IOS images, copying from TFTP servers, 114 security, SSL, 121 user authentication, 119
- 515. 606 IP addressing IP addressing, 33 address classes, 36 J-K ARP, 45-46 jam signals, 27 CIDR, 39 classful addressing, 40 KDC (Key Distribution Center), 225, 228 DHCP, 47 keepalive packets, generating, 376 DNS, 110-111 Kerberos, 225 enabling lookup on Cisco routers, 112 configuring, 228-229 logical AND operation, 37 realms, 227 name resolution on Windows NT systems, 292 key exchange management, IKE, 246 packets, 34-35 configuring, 252-259 RARP, 46 phase I, 247 subnetting 36 phase II, 248-250-252 calculating hosts per subnet, 37-38 VLSM, 38-39 IP GRE (generic routing encapsulation) tunnels L configuring, 349-351 ip helper-address command, 292 L2F (Layer 2 Forwarding), 229 ip host command, 110 VPDNs, 231 ip http authentication command, 119 L2TP (Layer 2 Tunneling Protocol), 229 IP multicast, 83 VPDNs, 231 IP packet debugging, 171-172 lab exam, 577-578 ip route-cache command, 168 FAQs, 578-580 ip subnet-zero command, 38 sample, 583-597 ipconfig command, 295-296 Land.C attacks, 371 IPSec, 242 lastlog file (UNIX), 290 AH, 244-246 layers of OSI reference model ESP, 243-244 application layer, 25 ISDN (Integrated Services Digital Network), 79 data link layer, 22 commands, 82 network layer, 23 framing, 80 IP, 33-37 layer 2 protocols, 80 spanning tree, 30 authentication, 82 switching, 28-30 HDCL, 80 physical layer, 21 LCP, 82 presentation layer, 24 NCP, 82 session layer, 24 PPP, 81 transport layer, 24 ISL (Inter-Switch Link), 33 LCP (link control protocol), 82 ISO (Organization for Standardization), 21 LDAP (Lightweight Directory Access Protocol), 133 ISOC (Internet Society) website, 368 learning state (spanning tree), 31
- 516. NetBT 607 leases (DHCP), viewing, 47 memory links, 289 NVRAM, 151 link-state protocols, OSPF, 66, 68 RAM, 151 example configuration, 71-75 ROM, 153 media types, 70 System Flash, 151 multiple area configuration, 69-70 messages, BGP, 76 single area configuration, 66, 69 method lists, 217 virtual links, 71 methods of attacks, 369 listening state (spanning tree), 31 metrics, administrative distance, 56-57 LLC sublayer, 22 MIBs, 122, 124 LMhosts file, 292 modes of IOS operation, 157 loading configuration files, 158 modifying local groups, 294 configuration registers, 177 Local Preference attribute (BGP), 77 UNIX permissions, 289 logging console debug command, 168 monitoring NAT, 327 logical AND operation, 37 motivation for attacks, 365 loops multicasting, 83 spanning tree, 30 multiple master domain model, 293 bridge port states, 31 mv command (UNIX), 284, 287 split horizon, 58 lost passwords, recovering, 174-179 ls command (UNIX), 284 N LSAs (link-state advertisements), 68 Nagle algorithm, preventing Cisco IOS from attacks, 375-376 M name resolution DNS, 110-111 MAC sublayer, 22 enabling lookup on Cisco routers, 112 MAIL command (SMTP), 128 on Windows NT, 292 man command (UNIX), 284, 287 NAT (Network Address Translation), 324 man in the middle attacks, 372 deploying, 325 managed devices, 123 Dynamic NAT, configuring, 326 manual keys versus preshared keys, 255 monitoring, 327 masquerading, 369 operation on Cisco routers, 326 master domain model, 293 NCP (Network Control Protocol), 82 MD5 (Message Digest 5), 239-240 NetBEUI (NetBIOS Extended User Interface), 290 MED attribute (BGP), 77 NetBIOS (Network Basic Input/Output media specifications of Ethernet, 27-28 System), 290 NetBT, 291
- 517. 608 NetRanger NetRanger, 300 NSSAs (Not-so-stubby areas), 70 Director, 302 NTFS (New Technology File System), 293 sensors, 300 NTP (Network Time Protocol), configuring clock supporting platforms, 301 sources, 128-131 typical network placement, 300 NVRAM (nonvolatile RAM), 151 NetSonar, 302-304 NWLink, 291 netstat command (UNIX), 287 network IDS, 372 network layer O bridging BPDUs, 31 operating systems port states UNIX ICMP, 52-53 command structure, 285-287 IP, 33 commands, 284-285 address classes, 36 development of, 284 logical AND operation, 37 file systems, 289-290 packets, 34-35 permissions, 288-289 subnets, 36 Windows NT, 290 spanning tree protocol, 30 browsing, 291 subnetting, VLSM, 38-39 domains, 290 switching, 28-29 global groups, 294 CAM tables, 29 local groups, 294 cut through, 30 name resolution, 292 store and forward, 30 permissions, 293-294 network layer (OSI model), 23 SAM, 293 network management, SNMP, 121 scalability, 292 community access strings, configuring on Cisco trust relationships, 294 routers, 121 workgroups, 290 configuring on Cisco routers, 124 Origin attribute (BGP), 77 examples of, 126 Originator ID attribute (BGP), 78 managed devices, 123 OSI reference model MIBs, 122-124 application layer, 25 notifications, 122-124 data link layer, 22 Network Neighborhood, 291 development of, 21 newsgroups, reporting security breaches, 368 network layer, 23 Next Hop attribute (BGP), 77 IP, 33-37 NMSs (network management systems), 123 spanning tree, 30 NOOP command (SMTP), 128 switching, 28-30 normal files, 289 peer-to-peer communication, 26 notifications (SNMP), 122-124 physical layer, 21
- 518. preshared keys versus manual keys 609 presentation layer, 24 encrypting, 181 session layer, 24 virtual terminal passwords, setting, 182 transport layer, 24 PAT (Port Address Translation), 324 versus TCP/IP model, 25 path vector protocols, BGP, 76 OSPF (Open Shortest Path First), 66-68 attributes, 77-78 example configuration, 71-75 configuring, 79 media types, 70 messages, 76 multiple area configuration, 69-70 PDM (PIX Device Manager), 299 single area configuration, 66, 69 peer-to-peer communication, 26 virtual links, 71 performing core dumps, 379-380 outside global addresses, 324 perimeter routers, 321 outside local addresses, 324 permissions UNIX, 288-289 P Windows NT, 293-294 PFS (perfect forward secrecy), 249 packet filtering, 321 physical layer (OSI model), 21 CBAC, 345 ping command, 285 configuring, 346-347 ping of death attack, 371 extended access lists, 187-189 ping requests, test characters, 52-53 options, 188-189 PIX (Private Internet Exchange), 328 standard access lists, 182-187 commands, 339-341 packets configuring, 332-337 AH, 245-246 DMZs, 330 Hello software features, 342-344 EIGRP, 63 stateful packet screening, 330-331 OSPF, 67 static routing, 337-338 IP, 34-35 PKI (Public Key Infrastructure), 348 debugging, 171-172 Poison Reverse updates, 59 rerouting, 369 policy routes, displaying, 166 TCP, 41-42 portfast, enabling, 31 partitioning System Flash, 151 PPP (Point-to-Point Protocol), 81 Passive FTP, 117-118 preparing for exam, 3, 7-8, 573-575 passwd file (UNIX), 290 FAQs, 576 password recovery, 174, 176-179 objectives, 4-7 passwords sample lab, 583-584, 586-597 authentication, 210 presentation layer (OSI model), 24 method lists, 217 preshared keys versus manual keys, 255, 453 enable passwords, setting, 180
- 519. 610 preventing Cisco IOS from attacks preventing Cisco IOS from attacks remote router access, 179 disabling default services, 378 rename command (DOS), 284 disabling DHCP, 377 reporting security breaches, Internet disabling TCP/UDP small servers, 376 newsgroups, 368 enabling sequence numbering, 378 rerouting packets, 369 enabling TCP intercept, 379 resolving IP addresses to MAC addresses, ARP, 45- Nagle algorithm, 375-376 46 performing core dumps, 379-380 rm command (UNIX), 284 PRI (Primary Rate Interface), 80 rmdir command (UNIX), 287 primary domain controllers, 290 ROM (read-only memory), 153 principal (Kerberos), 228 ROM boot mode (IOS), 157 privilege levels, authorization, 210-211 root bridge elections, 30 Privileged EXEC mode (IOS), 158 root bridges, 31 proxy servers, 321 route command, 296 routers hardware Q configuration registers, 154-156 CPU, 152 QUIT command (SMTP), 128 interfaces, 156 NVRAM, 151 RAM, 151 R ROM, 153 System Flash, 151 RADIUS (Remote Access Dial-In User remote access, 179 Service), 212 routing protocols, 53-55 attributes, 214 BGP, 76 configuring, 215-217 attributes, 77-78 features, 215 configuring, 79 security protocol support, 214 messages, 76 versus TACACAS+, 224-225 default administrative distances, 56-57 RAM, 151 EIGRP, 62-63 RARP (Reverse Address Resolution Protocol), 46 example configuration, 64-66 RCPT command (SMTP), 128 OSPF, 66-68 read command (SNMP), 123 example configuration, 71-75 recovering lost or unknown passwords, multiple area configuration, 69-70 174-179 single area configuration, 66, 69 redundancy, HSRP, 47 virtual links, 71 configuring, 50-51 RIP, 57-59 enabling, 49 configuring, 59-61 remote access, VPDNs, 229-231 configuring, 231-235
- 520. self-study lab 611 routing tables, viewing, 55-56 configuring Dynamic NAT, 326 RSET command (SMTP), 128 deploying, 325 RTO (Retransmission Timeout), 63 monitoring, 327 operation on Cisco routers, 326 packet filtering, TCP services, 322-324 S PAT, 324 PIX, 328 SA (Security Association), 242 commands, 339-341 sacrificial hosts, 370 configuring, 332-337 SAM (Security Accounts Manager), 293 DMZs, 330 SAML command (SMTP), 128 software features, 342-344 sample lab exam, 583-597 stateful packet screening, 330-331 saving configuration files, 158 static routing, 337-338 scalability, Windows NT, 292 PKI, 348 secret passwords, hiding, 181 RADIUS, 212 security, 321 attributes, 214 AAA, 208-209 configuring, 215-217 accounting, 211-212 features, 215 authentication, 210 security protocol support, 214 authorization, 210-211 SSH, 132-133 CBAC, configuring, 346-347 SSL, 121 encryption technologies, 235 TACACS+, 218 3DES, 238 authentication, 219 DES, 237-238 authorization, 219-220 Diffie-Hellman, 240-241 configuring, 220-223 DSS, 238-239 features, 220 IPSec, 242-246 versus RADIUS, 224-225 MD5, 239-240 VPDNs, 229-231 principles of, 235-237 configuring, 231-235 firewalls, 320 VPNs, 349 Cisco IOS features, 344-345 configuring, 350-351 HTTP, 118 security server protocols, 212 authentication, 119 Security Wheel, 304 IKE, 246 self-study lab configuring, 252-259 ACS configuration, 461--470 phase I, 247 advanced PIX configuration, 458-460 phase II, 248- 252 BGP routing configuration, 438-442 Kerberos, 225 Catalyst Ethernet switch setup, 403-413 configuring, 228-229 DHCP configuration, 438 NAT, 324
- 521. 612 self-study lab dynamic ACL/lock and key feature show ip arp command, 46 configuration, 448-449 show ip route command, 55-56, 162-163 final configurations, 470-485 show logging command, 166 Frame Relay setup, 397-402 show process command, 153 IGP routing, 419-423 show route-map command, 166 OSPF configuration, 423-432 show startup-config command, 178 IOS Firewall configuration, 450-451 show version command, 155-156, 166 IP access list configuration, 442-444 SIA (Stuck in Active), 63 IPSec configuration, 452-457 Signature Engines, 373-374 ISDN configuration, 432-437 single domain model, 293 local IP host address configuration, 414 single logon, 226 physical connectivity, 403 sliding windows, 44 PIX configuration, 414-418 SMTP (Simple Mail Transfer Protocol), 127 setup, 393-395 commands, 127-128 communications server, 396-397 smurf attacks, 372 TCP intercept configuration, 444-446 SNMP, 121 time-based access list configuration, 446-448 community access strings, configuring on Cisco SEND command (SMTP), 128 routers, 121 Sendmail, 127 configuring on Cisco routers, 124 sensors, Cisco IDSs, 373 examples of, 126 sequence numbering, enabling, 378 managed devices, 123 servers, RADIUS, 212 MIBs, 122, 124 service password-encryption command, 181 notifications, 122, 124 service tcp keepalive command, enabling Nagle snmp-server community command (SNMP), 124 algorithm, 376 snmp-server enable traps config command, 124 service tcp-keepalives-in command, 376 snmp-server host command, 124-126 session hijacking, 369 social engineering, 367 session layer (OSI model), 24 software session replay, 369 Cisco Secure, 297, 299 set vlan command, 30 AAA features, 298 SGBP (Stack Group Bidding Protocol), 85-86 features, 297 SHA (Secure Hash Algorithm), 239-240 test topics, 297 shadow file (UNIX), 290 NetSonar, 302, 304 show accounting command, 211-212 software features of PIX, 342-344 show commands, 160-161 SOML command (SMTP), 128 show debugging command, 163 spanning tree, 30 show interface command, 156 bridge port states, 31 show interfaces command, 163-165 special files, 289 show ip access-lists command, 163 SPI (Security Parameters Index), 243
- 522. teardrop attacks 613 split horizon, 58 spoof attacks, 372 T SRTT (Smooth Route Trip Time), 63 TACACS+ (Terminal Access Controller Access SSH (Secure Shell), 132-133 Control System Plus), 218 SSL (Secure Socket Layer), 121 authentication, 219 standard access lists, 182-187 authorization, 219-220 standard IP access lists, 183 configuring, 220-223 wildcard masks, 184 features, 220 standards bodies, CERT/CC, 366 versus RADIUS, 224-225 startup config, viewing, 178 TCP (Transmission Control Protocol), 40 stateful packet screening, PIX, 330-331 ARP, 45-46 stateful security, 330 DHCP, 47 states of Ethernet interfaces, 165 FTP, 53 static NAT, 327 header format, 41 static routing, PIX configuration, 337-338 HSRP, 47 store and forward switching, 30 configuring, 50-51 stratum, 128-129 enabling, 49 configuring NTP time sources, 130-131 ICMP, 52-53 stubby areas, 70 load distribution, 328 study tips for exam, 569-570, 575 packets, 41-42 study tips for qualification exam, 570-571 RARP, 46 decoding ambiguity, 572-573 services, filtering, 322, 324 subnetting, 36 Telnet, 53 calculating host per subnet, 37-38 Telnet requests, 42, 45 CIDR, 39-40 three-way handshakes, 44 VLSM, 38-39 TFTP, 53 successors (EIGRP), 63 TCP half close, 44 summary links, 68 TCP intercept, enabling, 379 switching, 28-29 TCP SYN Flood attacks, 371 CAM tables, 29 TCP/IP (Transmission Control Protocol/Internet cut through, 30 Protocol) portfast, enabling, 31 FTP protocol store and forward, 30 Active mode, 115-117 trunks, 31 Passive mode, 117-118 System Flash, 151 vulnerabilities, 369-370 system log, displaying, 166 TCP/IP model versus OSI reference model, 25 teardrop attacks, 371
- 523. 614 Telnet Telnet, 53 UNIX connections, establishing, 179 commands disabling login password, 113 correlated DOS commands, 284-285 requests, 42, 45 structure, 285-287 test characters (ping), 52-53 development of, 284 TFTP (Trivial File Transport Protocol), 53, 113 file systems, 289 defining download directory, 114 directories, 289-290 TGT (Ticket Granting Ticket), 228 permissions, 288-289 time sources (NTP) unknown passwords, recovering, 174-179 configuring, 130-131 URLs, Cisco security products, 304 stratum, 128-129 user account permissions timestamps, 226 UNIX, 288-289 topology table (EIGRP), 63 Windows NT, 293-294 totally stubby areas, 70 user authentication, HTTP, 119 traceroute command (UNIX), 285 User EXEC mode (IOS), 158 tracert command (DOS), 285 transform sets (IKE), defining, 253 transparent bridging, 30 V transport layer (OSI model), 24 Transport mode (IPSec), 242 versions of SNMP, 121 trap command (SNMP), 123 viewing traps (SNMP), 122 configuration register, 155 triggered updates, 59 DHCP leases, 47 trunks, 31 home pages, 118 trusted domains, 292 interfaces, 156 trusting domains, 294 routing tables, 55-56 Tunnel mode (IPSec), 242 startup config, 178 tunneling virtual links, 71 IP GRE, 349-351 virtual terminal passwords, setting, 182 VPDNs, 229-231 VLANs (virtual LANs), creating, 30 configuring, 231-235 VLSM (variable-length subnet masking), 38-39 turning off debugging, 163 VPDNs (Virtual Private Dial-up Networks), 229-231 configuring, 231-235 VPNs (virtual private networks), 349 U configuring, 350-351 VRFY command (SMTP), 128 UDP bombs, 371 vulnerabilities undebug all command, 163 of network systems, investigating with NetSonar, 302-304 of TCP/IP, 369-370
- 524. xcopy command 615 W-X-Y-Z websites Cisco Product Security Incident Response Team, 367 IETF, 368 Internet Domain Survey, 368 ISOC, 368 Weight attribute (BGP), 78 wildcard masks, 184 Windows Active Directory, 133 Windows NT, 290 browsing, 291 domains, 290 trust relationships, 294 global groups, 294 local groups, 294 name resolution, 292 permissions, 293-294 SAM, 293 scalability, 292 workgroups, 290 WINS (Windows Internet Naming Services), 292 workgroups, 290 write command (SNMP), 123 written exam FAQs, 576-577 preparing for, 573-574 study tips, 570-571 decoding ambiguity, 572-573 wtmp file (UNIX), 290 xcopy command (DOS), 284