Ch13 system administration

System Backups and Disaster
Recovery
Chapter 13

Chapter Goals
• Understanding the importance of backups.
• Understand the issues associated with
backups.
• Understand backup strategies and
scheduling.
• Understand the basics of backup devices.
• Understand the basics of backup media.
• Understand the various types of backup
software.

Importance of System Backups
• Which Files Should Be Backed Up?
– OS Binaries?
– Applications?
– Configuration Files?
– User files?
– Log files?
• Generally, full backups of everything are easiest to manage, but
backup of system files is creating extra work for yourself.
– Possibly full dump when installed, then again after
patches/upgrades.
• Backup of just user files is not enough.
• Should dump the log files, and configuration information.

Importance of System Backups
• How Often Should Backups Be Performed?
– Need to determine what level of data loss is
acceptable:
• Web sales? - need very fine grain backups.
• Banking/Insurance? - very fine grain.
• Research and development? - fine to medium grain.
• University? - medium grain.
• Mom and Pop? - coarse grain.

Backup Strategy and Scheduling
• Types of Backups
– Full backup– dump every file to dump media.
– Partial (incremental) backup – dump all files that
have changed since last lower level backup to dump
media.
• Unix uses a multi-level partial scheme (level 0 is a full,
level 1 – 9 are incremental).
– All files that have been modified since the last ufsdump at a
lower dump level are copied to the dump media.
– For instance, if a "level 2" dump was done on Monday,
followed by a "level 4" dump on Tuesday, a subsequent
"level 3 dump on Wednesday would contain all files modified
or added since the "level 2" (Monday) backup.
– A "level 0" dump copies the entire file system to the
dump media.

• Backup Strategies
– There are several algorithms that might be used to schedule
full and partial backups.
– The choice of algorithm dictates the amount of media required.
– The choice of algorithm plays a large role in the size of the
restore window (how long is data available from a backup
tape).
– Some of the more popular algorithms are:
• Volume/Calendar Backup
• Grandfather/Father/Son Backup
• Tower of Hanoi Backup

• Volume/Calendar Backup
– The volume/calendar backup strategy calls for a full system
backup once a month.
– An incremental backup is performed once a week for files that
change often.
– Daily incremental backups catch files that have changed since
the last daily backup.
– A typical schedule would be to perform the full (level 0) backup
one Sunday a month, and weekly level 3 backups every Sunday
of the month.
– Daily level 5 backups would be performed Monday through
Saturday.
– This would require eight complete sets of media (one monthly
tape, one weekly tape, and six daily tapes)

Volume Calendar
Su M Tu W Th F Sa
Week 1 Tape A B C D E F G
Level 0 5 5 5 5 5 5
Weeks 2, 3, 4 H
Level 3 5 5 5 5 5 5
• Recovering from complete data loss with the volume/calendar scheme
requires restoring from the most recent full backup, then restoring from
the most recent weekly backup, and finally, restoring from each daily
backup tape written since the weekly backup.
• An advantage to this backup scheme is that it requires a minimum of
media, but this also points out one of the major problems with this backup
scheme: tapes are immediately reused.
– For example, every Monday overwrites last Monday’s backup
information. Consider what would happen if one of the disk drives
failed during the second Monday backup.
– It would not be possible to recover all data, because the system was in
the process of overwriting the backup tape when the drive failed.

• Grandfather/Father/Son Backup
– The grandfather/father/son backup strategy is similar to the
volume/calendar strategy.
• The major difference between the two schemes is that the
grandfather/father/son method incorporates a one-month archive
in the backup scheme. This eliminates the problem of overwriting
a tape before completing a more recent backup of the file
system.
• Implementing the grandfather/father/son strategy requires
performing a full (level 0) dump once a month to new media.
• Once a week, an incremental (level 3) backup must be
performed that captures all files changed since the last weekly
backup.
• This weekly backup should also be saved on new media.
• Each day an incremental level 5 backup must be performed to
capture files that have changed since the last daily backup.
•

Grandfather/Father/Son
Su M Tu W Th F Sa
Week 1 Tape A B C D E F G
Level 0 5 5 5 5 5 3
Week 2 Tape H I
Level 5 3
Week 3 Tape H J
Level 5 3
Week 4 Tape H K
Level 5 3
Week 5 L M
Level 0 3
Week 6 Tape H G
Level 5 3
Week 7 Tape H I
Level 5 3
Week 8 Tape H J
Level 5 3
Week 9 Tape A
Level 0

Grandfather/father/son
• To maintain a one-month archive, the monthly full backup tape should be
placed in storage.
• Each weekly full backup should be placed in storage.
• The second monthly full backup, should use new media.
• When the third monthly backup is due, the first month’s full backup media
should be reused. The weekly backups are archived in a similar manner.
• This scheme requires two sets of monthly backup media, five sets of
weekly backup media, and six sets of daily backup media.
• A total of 13 sets of media are required to implement this strategy with a
one-month archive of information.
• To recover from complete data loss, first restore the most recent level 0
backup tape.
• Next, restore from the most recent of the level 3 backups, if that backup
was written after the level 0 backup.
• When the level 3 backup has been restored, the operator would restore
from each of the level 5 backups written after the level 3 backup.
• This backup strategy requires much more media than the simple volume /
calendar strategy. Although media cost is increased with this plan, data
survivability also increases.

– The Tower of Hanoi backup strategy is a variation of “exponential
backup.” Both strategies rely on functions of powers of 2.
– For example, the use of five backup tapes provides for a 32-day
schedule. The use of six tapes would provide for a 64-day
schedule.
– The Tower of Hanoi backup schedule provides outstanding data
survivability and a minimum of media. Unfortunately, on a seven-
day backup system, the scheduling of full backups as opposed to
partial backups can become a problem for the operator.
– One way to avoid operator confusion is to perform a special level
0 backup on the first day of each month. This tape would not be
one of the five tapes used in the backup cycle. Total media
requirements in this scheme would be seven sets of media.

Su M Tu W Th F Sa
Week 1 Tape E A B A C A B
Level 0 5 4 5 3 5 4
Week 2 Tape A D A B A C A
Level 5 1 5 4 5 3 5
Week 3 Tape B A E A B A C
Level 4 5 0 5 4 5 3
Week 4 Tape A B A D A B A
Level 5 4 5 1 5 4 5
Week 5 C A B A E A B
Level 3 5 4 5 0 5 4
Week 6 Tape A C A B A D A
Level 5 3 5 4 5 1 5
Week 7 Tape B A C A B A E
Level 4 5 3 5 4 5 0
Week 8 Tape A B A C A B A
Level 5 4 5 3 5 4 5
Week 9 Tape D A B
Level 1 5 4

– To recover from complete data loss, first restore from the most
recent level 0 backup, and then restore from the level 1 backup if
that backup was written after the level 0 backup.
– Next, restore consecutively from the most recent level 3 and 4
backups if both were written after the level 0 backup.
– Finally, restore each of the level 5 backups that were written after
the level 0 backup.

Reasonable Alternative
• The following four-week schedule offers a reasonable backup schedule
for most sites.
• Performing a full dump on the first Sunday of the month provides a
monthly snapshot of the system data.
• Using two sets of dump media allows the operator to store information
for two full months.
• Note that in the example the Tuesday through Friday incremental
backups contain extra copies of files from Monday.
• This schedule ensures that any file modified during the week can be
recovered from the previous day’s incremental dump.
• To recover from complete data loss, restore the most recent full (level 0)
backup tape.
• Next, restore from the most recent of the weekly (level 3) backups. Once
the weekly backups are restored, restore from each of the daily (level 5)
backups.

A Reasonable Alternative?
Su M Tu W Th F Sa
Week 1 Tape A B C D E
Level 0 5 5 5 3
Week 2 Tape F B C D E
Level 5 5 5 5 3
Level 5 5 5 5 3
Level 5 5 5 5 3

Backup Devices
• Backup devices must exhibit the following traits:
– User ability to write data to the device.
– Media capable of storing the data for long periods.
– Support of standard system interconnects.
– Support of reasonable input/output throughput.

Backup Devices
• Tape Backup Devices
– Cartridge Tape Drive
– 8-mm Tape Drive
– Digital Audio Tape Drive
– Linear Tape Open
– Digital Linear Tape
– Jukebox/Stacker Systems
• Optical Backup Devices
• Magneto-optical Backup Devices
• Disk Systems As Backup Devices
– RAID Disk Arrays
– Problems with Disks As Backup Devices
• High-Density Removable Media Backups

Backup Devices
• Tape backup devices are probably the most common
backup media in use.
– The media is relatively inexpensive, the performance is
reasonable, the data formats are standardized, and tape drives
are easy to use.
– These factors combined make magnetic tape backups an
attractive option.
– Most current-generation tape drives offer “native” mode and
compressed mode storage capabilities.
• Generally, the manufacturers claim a 2:1 compression ratio, but
this value may vary based on the data to be stored.
• Binaries (images, compiled programs, audio files, and so on)
may not be significantly smaller when compressed, whereas text
files may compress very well.

Tape Backup Devices
• Cartridge Tape Drive
– Cartridge tape drives store between 10 Mb and several Gb of data on a
small tape cartridge.
– Most cartridge tape systems use SCSI interconnections to the host
system.
– These devices support data transfer rates up to 5 Mb per second. The
actual transfer rate from the tape drive memory to the tape media is
typically about 500 Kb per second.
• 8-mm Tape Drive
– These tape drives are also small and fast, and use relatively inexpensive
tape media.
– The 8-mm media can hold between 2 and 100 GB of data, depending on
the drive model and type of tape in use.
– The 8-mm drives use the SCSI bus as the system inter-connection.
– Low-density 8-mm drives can store 2.2 Gb of information on tape. and
transfer data to the tape at 250 Kb per second. High-density 8-mm drives
can store up to 80 GB of information on a tape at a 16 MB/second.
– “low” end, the 8-mm drives do not use data compression to store the data
on tape. “high” end, advanced intelligent tape drives incorporate
compression hardware and improved recording techniques to increase
the amount of information that can be stored on the tape.

Tape Backup Devices
• Digital Audio Tape Drive
– Digital audio tape (DAT) drives are small, fast, and use
relatively inexpensive tape media. Typical DAT media
can hold between 2 and 40 GB of data.
– Although manufacturers of DAT devices have announced
the end-of-life for these products, they will remain in use
for many years.
– The various densities available on DAT drives are due to
data compression. A standard DAT drive can write 2 Gb
of data to a tape. By using various data compression
algorithms, and various lengths of tape, manufacturers
have produced drives that can store between 2 and 40
GB of data on a tape.
– DAT drives use SCSI bus interconnections to the host
system, and typically offer 3 MB/second throughput.

Tape Backup Devices
• Linear Tape Open
– A consortium of Hewlett Packard, IBM, and Seagate
developed the LTO technology. LTO encompasses two
formats: the Ultrium, a high-capacity solution, and Accelis
format, a fast-access format. The two formats use
different tape drives, and tape cartridges.
– LTO Ultrium drives can store up to 100 Gb of data on a
single tape cartridge at 16 Mb/second.

Tape Backup Devices
• Digital Linear Tape
– Digital linear tape (DLT) backup devices are also relatively new on
the backup market.
– These tape devices offer huge data storage capabilities, high
transfer rates, and small (but somewhat costly) media.
– Digital linear tape drives can store up to 110 Gb of data on a single
tape cartridge. Transfer rates of 11 Mb/second are possible on high-
end Super-DLT drives, making them very attractive at sites with
large on-line storage systems.
– Where 8-mm and DAT tapes cost (roughly) $15 per tape, the LTO,
AIT, and DLT tapes can run as much as $150 each. However, when
the tape capacity is factored into the equation, the costs of these
high-capacity tapes become much more reasonable.
• Consider an 8-mm tape that holds (up to) 14 Gb on average versus
a LTO cartridge, which can hold 100 Gb of data!

Tape Backup Devices
• Jukebox/Stacker Systems
– Jukebox or stacker systems combine an automated
mechanism with one or more tape drives.
– Stackers are sequential tape systems. Tapes are stacked
in a hopper, and the tape drive starts by loading the tape
at the bottom of the stack. When the tape is full, it is
ejected, and the next tape is loaded from the stack.
– Many stackers do not have the capability to load a
specific tape in the drive. Instead, these stackers simply
cycle (sequentially) through the tapes until the last tape is
reached. At this point they can either start the cycle over
again or wait for a new group of tapes to be loaded into
the hopper.

Tape Backup Devices
• Jukebox/Stacker Systems
– Unlike stackers, jukebox systems employ multiple tape
drives, and special “robotic” hardware to load and unload
the tapes.
– Jukebox systems require special software to control the
robotics. The software keeps track of the content of each
tape and builds an index to allow the user to quickly load
the correct tape on demand. Each tape is “labeled” with a
bar-code decal (or something similar), and the
mechanism contains a label reader that keeps track of
what tape is in the drive. Many commercially available
backup software packages allow the use of jukebox
systems to permit backup automation.

Optical Backup Devices
– Recently, optical storage devices have become another economical
means of backing up mass storage systems.
– Compact disk read-only-memory devices (CD-ROM) are useful for
long-term archive of information.
• Although the name implies that these are read-only devices, recent
technology has made it possible to mass market the devices that
create the encoded CD-ROM media.
• These CD-ROM writers (also called CD-recordables) make it
possible to consider CD-ROM as a backup device. More recent
versions of this technology have produced rewritable CD-ROMs
(CD-RW or CDR).

Optical Backup Devices
– One of the major decisions in choosing a backup device is the ability
of the medium to store information for long periods.
• CD-ROM media offer excellent data survivability.
• Another advantage to the CD-ROM is the availability of reliable data
transportability between systems. This reliability is possible due to
the CD-ROM’s adherence to industry standardized data formats.
• Along with these advantages, the CD-ROM offers a few unique
disadvantages. The foremost disadvantage to the CD-ROM as a
backup device is the setup cost to create a CD. Setting up and
creating a CD is a time-intensive operation.
– Some small sites may decide to back up to CD-ROM rewritable (CDR)
media. The CDR format allows the reuse of optical media, thereby
reducing the cost of backing up to optical devices.
• Unfortunately, the CDR is still a low-density solution, providing a
mere 650 Mb of storage per disk. The setup and record time for
CDR is comparable to CD-ROM media, making CDR less attractive
for backups at large sites.

Magneto-Optical Backup Devices
• Magneto-optical Backup Devices
– Optical storage systems and associated media are typically expensive.
They are also relatively slow devices. Consequently, optical storage
systems are rarely used as backup devices at large sites.
• In contrast, magnetic tape (or disk) storage systems are
inexpensive and fast. Unfortunately, the media is bulky and
susceptible to damage and data loss.
• By combining the two storage systems into a single system,
manufacturers have been able to provide fast, inexpensive, and
reliable backup systems.
– Many of the magneto-optical systems are hierarchical, meaning that
they keep track of how long a file has been in storage since the last
modification.
• Files that are not accessed or modified are often eligible to be
stored on the slower optical storage section of the system.
• Frequently accessed files are maintained on the magnetic storage
section of these systems, which allows for faster access to files.
– Most magneto-optical storage systems use standard SCSI bus system
interconnections. These systems can typically provide the same (or
better) data transfer rates as SCSI tape and disk systems.

Disk Backup Devices
• Disk Systems As Backup Devices
– One problem involved in using tape devices for backups is the
(relatively) low data throughput rate.
– If the operator had to back up several gigabytes or terabytes of data
daily, it would not take long to realize that tape drives are not the best
backup method.
– Although optical backup devices offer high storage capacity, the
optical devices are often much slower than tape devices.
– One popular method of backing up large-scale systems is to make
backup copies of the data on several disk drives.
• Disk drives are orders of magnitude faster than tape devices, and
therefore offer a solution to one of the backup problems on large-
scale systems.
– However, disk drives are much more expensive than tapes.
– Disk backups also consume large amounts of system
resources.
– For example, you would need 100 2-Gb disks to back up 100 2-
Gb disks. Fortunately, there are software applications and
hardware systems available to transparently perform this
function.

Disk Backup Devices
• RAID Disk Arrays
– One operating mode of redundant arrays of inexpensive disks
(RAID) enables the system to make mirror image copies of all data
on backup disk drives.
– RAID disk arrays also allow data striping for high-speed data access.
– Yet another mode stores the original data, as well as parity
information on the RAID disks. If a drive should fail, the parity
information may be used to recreate the data from the failed drive.
• Problems with Disks As Backup Devices
– When tape devices are employed as the backup platform, it is a
simple matter to keep a copy of the backups off-site.
– When disk drives are employed as a backup media, the process of
keeping a copy of the backup media off-site becomes a bit more
complicated (not to mention much more expensive).
• In the case of a RAID disk array, the primary copy of the data is
stored on one disk, and the backup copy of the data is stored on
another disk. However, both disks are housed in a single box. This
makes the task of moving one drive off-site much more
complicated.

Disk Backup Devices
– RAID disk arrays have recently been equipped with fiber channel
interfaces.
– The fiber channel is a high-speed interconnect that allows devices to
be located several kilometers from the computer.
• By linking RAID disk arrays to systems via optical fibers, it is
possible to have an exact copy of the data at a great distance from
the primary computing site at all times.
• High-Density Removable Media Backups
– A relatively recent addition to the backup market is the high-density
removable media drive.
– Examples of these devices include the Iomega ZIP and JAZ drives, and
the Imation Superdisk drives.
• These devices are capable of recording 100 Mb to 2 Gb of data on a
removable medium that resembles a floppy diskette.
– Until recently, UNIX could not make use of these high-density
removable media devices.
– Many of these devices employ a parallel port interface. A few of them
offer SCSI interfaces, allowing them to be connected to the external
SCSI port on a workstation.

Unix Backup Commands
• Unix operating environments include a plethora of backup
utilities.
– The [ufs]dump and [ufs]restore utilities are available under most
UNIX variants.
• The dump application was developed to allow the backup of entire
systems one at a time.
• The dump program allows the operator to specify files to be
“dumped” (or backed up to tape), and options to use during the
dump.
• In addition, dump enables scheduling of different levels of dumps
on different days.
• The dump command also allows for dumps that occupy multiple
tape reels.

UNIX Backup Commands
• dump [options] [arguments] files_to_dump
– NOTE: The dump command requires that the user have read access
privileges on the system disks.
• 0-9: These numeric values specify the dump level. All files that have
been modified since the last dump at a lower dump level are copied
to the media.
• b: Signifies the blocking factor to be used. The default is 20 blocks
per write for tape densities of 6,250 BPI (bytes per inch) or less.
The blocking factor of 64 is used for tapes with 6,250 BPI or greater
density. The default blocking factor for cartridge tapes is 126.
NOTE: blocking factor is specified in 512-byte blocks.
• c: Signifies that the backup device is a cartridge tape drive. The
option sets the density to 1,000 BPI and the blocking factor to 126.
• d: Signifies the density of the backup media in BPIs. The default
density is 6,250 BPI except when the c option is used. When the c
option is used, the density is set to 1,000 BPI per track.

• D: Signifies that the dump device is a floppy diskette.
• f: Signifies the dump file. This option causes dump to use
dump file as the file to dump to, instead of /dev/rmt/0.
• s: Signifies the size of the backup volume. This option is not normally
required because dump can detect end-of-media. When the specified
size is reached, dump waits for the operator to change the volume. The
size parameter is interpreted as the length in feet for tapes and
cartridges, and as the number of 1,024-byte blocks for diskettes.
• u: This option causes dump to annotate which file systems were
dumped, the dump level, and the date in the /etc/dumpdates file.
• v: This letter signifies that dump should verify the content of the backup
media after each tape or diskette is written.
• # dump 0fu /dev/rmt/0 /dev/rdsk/c0t3d0s2

• Now that file systems have been copied onto a tape, how is this
information retrieved?
– UNIX provides an application to restore data from the backup media
to the system mass storage devices.
– This application is called restore.
• /usr/sbin/restore options [ arguments ] [ filename ... ]
• Some of the most useful options to the restore com-mands follow.
– i: Places restore in the interactive mode. Com-mands available in this
mode follow.
– add [filename]: Adds the named file or directory to the list of files to be
extracted.
– cd directory: Changes to directory on the dump media.
– delete [filename]: Deletes the current directory or file from the list of
files to be extracted.
– extract: Extracts all files on the extraction list from the dump media.

– ls [directory]: Lists files in directory (dump media) or the current
directory, which is represented by a period (.).
– pwd: Prints the full path name of the current working directory.
– quit: Exits immediately.
– verbose: Toggles the verbose flag (the program prints a line for every
action it takes).
– r: Restores the entire content of the media into the current directory.
– x: Extracts the named files from the media.
– b: Sets the restore blocking factor.
– f [dump file]: Tells restore to use the dump file instead of /dev/rmt/0 as
the file to restore from.
– R: Resumes restore after volume is changed.
– t: Prints table of contents for dump file.
– n: Skips to the nth file when multiple dump files exist on the same
tape.
– v: Displays the name and inode number of each file restored.
– Note that the i, r, R, t, and x arguments are mutually exclusive. Only
one of these arguments may be used at a time.

• Example restore Commands
# restore rbf 50 /dev/rmt/0 /dev/rdsk/c0t2d0s2

# restore ibf 50 /dev/rmt/0

• Remote Backup and Restore
– How can a file system dump be performed on a system without a
backup device?
– The dump and restore commands allow input and output to be sent
to the standard input and output streams. This flexibility allows the
dump/restore output to be sent through the network to a system with
a backup device.
– The -f option for dump and restore specifies the dump device.
– f dump file: This option tells dump to use dump file as the file to
dump to. If dump file is specified as a hyphen ( - ), dump will dump to
standard output. If the name of the file is of the form machine:device,
the dump is carried out from the specified machine over the network
using the rmt facility.
– NOTE: Because dump is normally run by root, the name of the local
machine must appear in the /.rhosts file of the remote machine.

– To perform a remote restore using the restore command,
the operator can make use of the -f option again.
– f dump file: This option tells restore to use dump file as
the file to restore from. If dump file is specified as a
hyphen ( - ), restore reads from the standard input.
– NOTE: Because restore is also normally run by root, the
name of the local machine must appear in the /.rhosts file
of the remote machine.
– To copy a home partition to another machine with a
remote restore, consider the following command, sub-
stituting the appropriate directory and device names.
– # dump 0f - /dev/rdsk/c0t2d0s2 | (rsh machine ; cd
/home;restore xf -)

• tar Command
• What happens if the operator does not want to dump and restore complete
file systems?
– For example, what if a user simply wants to make a tape of the data
associated with one project?
– Most UNIX derivatives provide a standardized utility called tar. The tar
command creates tape archives and provides the ability to add and
extract files from these archives.
% tar c -C /home/project include -C /data/project
% tar cvf /dev/rmt/0
– Create a tar archive on device /dev/rmt/0
% tar tvf /dev/rmt/0
– List the contents of the tar archive on /dev/rmt/0
% tar xvf /dev/rmt/0
– Extract the contents of the tar archive on /dev/rmt/0

• Another command that may be used to back up and restore
files is cpio.
• The cpio command copies file archives “in and out.”
• The syntax for the cpio command follows.
cpio -key [options] filename
• The key option to cpio determines the actions to be
performed. The following flags are mutually exclusive.

• % ls | cpio -oc >> ../newfile
– NOTE: The find, echo, and cat commands can
also be used as substitutes for the ls command to
produce a list of files to be included in ../newfile.
• To extract the files from ../newfile, issue the following
command.
• % cat newfile | cpio -icd
• % find . -depth -print | cpio -pdlmv newdir
– NOTE: When using cpio in conjunction with find,
use the L option with cpio, and the -follow option
with find.

• Yet another command available to use as a backup-and-
restore utility is the dd utility.
• The dd command copies the input file to output, applying
any desired conversions in the process.
• When complete, dd reports the number of whole and partial
input and output blocks.
dd [ option = value ] ....

• Do not use dd to copy files between file systems
with different block sizes.
• Using a blocked device to copy a file will result in
extra nulls being added to the file, in order to pad
the final block to the block boundary.
• When dd reads from a pipe, using the ibs = X and
obs = Y operands, the output will always be
blocked in chunks of size Y.
• When bs = Z is used, the output block size will be
whatever could be read from the pipe at the time.

• if = filename: Use filename as the input file. stdin is the default value.
• of = filename: Use filename as the output file. stdout is the default value.
• ibs = n: Use n as the input block size. 512 is the default value.
• obs = n: Use n as the output block size. 512 is the default value.
• bs = n: Use n as the input and output block size This supersedes the ibn
and obn arguments. If no conversion is specified, preserve input block
size.
• files = n: Copy and concatenate n input files before terminating.
• skip = n: Skip n input blocks before performing copy.
• iseek = n: Seek n blocks from the beginning of the input file before
copying.
• oseek = n: Seek n blocks from the beginning of the output file before
copying.
• count = n: Copy n input blocks.
• swab: Swap every pair of bytes.
• sync: Pad every input block to ibs.

# dd if=/dev/rdsk/c1t3d0s2 of=/dev/rmt/2 bs=20b
# dd if=/dev/rmt/2 of=/dev/rdsk/c2t1d0s2 bs=20b

Windows Backup Commands
• Like its UNIX cousins, Windows provides a utility to perform
file system backups.
• The Windows backup-and-restore utility (backup.exe)
provides for backups, and restores.
– In backup mode, the operator is given the ability to select which
disk and/or files to back up, whether the local registry should be
dumped, whether the backup should use compression, and what
users may read the backup tape(s).
– Otherwise, the “menu” of backup options available to the operator
is pretty limited.

• The Options menu under the Tools menu allows the
operator to determine the type of backup to be performed,
whether data should be verified after the backup is
performed, the amount of detail supplied in the log files,
whether new media should be used, backup scheduling,
and other configuration parameters for the backup utility.

• The Windows backup utility also provides the interface to the restore
function.
– In restore mode, the utility displays a catalog of the tape, allowing
the user to select which files/directories need to be restored.
– The operator is also given the choice of where the file is to be
restored.
• Although the GUI may simplify the setup of Windows backups, it also
limits the choices available to the operator. Because this utility is based
on the backup utility offered in the consumer versions of Windows, the
sysadmin at a commercial site may decide that the Windows backup
utility is not the first choice for backup software at the site. Many third-
party backup utilities are available for Windows systems, including
Amanda, Legato Networker, and the Veritas backup suite.

Dealing with Specific Backup Issues
• Certain aspects of successful backup and restore
strategies require special attention.
– For instance, how could the operator restore the root
file system if the root disk had crashed and there
was no way to boot the system?
– Many administrators are also concerned with how to
automate backups to minimize time investment while
ensuring successful backups.
– Next, what happens if a backup requires 2 Gb of
backup media, but the backup device can write only
1 Gb to the media?

• Restoring the Root File System
– One of the most difficult problems faced when using
restore is restoring the root file system.
• If the root file system is missing, it is not possible to boot the
damaged system, and there would not be a file system tree to
restore to.
• One way to accomplish a root file system reload is by booting the
system to the single-user state from the CD-ROM distribution
media.
• Another way to reload the root file system would be to boot the
system to the single-user state as a client of another system on
the network.
• Another method of restoring the root file system is to remove the
disk from the system, and attach it to a working system.

• Multi-volume Dumps
– Two of the backup commands mentioned in this chapter also allow
for multi-volume backups.
• The dump command and the cpio command allow a backup to be
stored over multiple media sets.
• The other commands (tar and dd) will allow the user to split the
backups onto several sets of media, but these commands require
that the user perform much of the work manually.
• The cpio command watches for the “end of medium” event. When
cpio detects this event, it stops and prints the following message
on the terminal screen.
If you want to go on, type device/file name when ready.
• To continue the dump, the operator must replace the medium and
type the character-special device name (e.g., /dev/rdiskette) and
press Enter. At this point, the operator may choose to have cpio
continue the backup to another device by typing the device’s name
at the prompt.

• Multi-volume Dumps
– Using dump as the backup command is somewhat
simpler.
• Like cpio, dump will detect the end-of-medium event and
stop operation.
• The dump command will then wait for the operator to
change the medium before it continues.
• Unlike cpio, dump does not need the name of the backup
device to continue.
• The operator simply needs to confirm that the medium has
been changed and that everything is ready for dump to
continue operation.

Automated Backups
• Cheap and Dirty
• #!/bin/sh
• # dump /, /usr, /var, /home, /opt, /orasoft
• #
• mt -f /dev/nst0 rewind
• dump 0bdfu 50 54000 /dev/nst0 /dev/ida/c0d1p2
• mt -f /dev/nst0 rewind
• mt -f /dev/nst0 offline
• # sh -x /dodump

Cross Platform Backups
• Several utilities are available for cross-platform backups:
– Veritas
– Legato Networker
– RaxCo
– Amanda – free – http://www.amanda.org/

Summary
• This chapter explored the commands that can be used to
make backup copies of system data, why it is important to
make such backup copies of data, and selected methods of
avoiding data loss due to natural or other disasters.
• The authors hope that readers never have to use any of
these backup copies to restore the operation of their
systems, but such restorations are inevitable.
• Good backups require a lot of time and attention, but having
a reliable copy of data is much more acceptable than the
time and expense of rebuilding a system without such
backup copies.

Ch13 system administration

More Related Content

Viewers also liked (20)

Similar to Ch13 system administration (20)

More from Raja Waseem Akhtar (20)

Recently uploaded (20)

Ch13 system administration

Editor's Notes