Chapter 02 Using Drawing Tools.ppt

Chapter 2
Using Drawing Tools
& Applied Geometry

TOPICS
Preparation of Tools.
Using of Tools
Applied Geometry

Fastening Paper to Drafting Board
1. Place the paper close to the table’s left edge.
2. Move the paper until its lower edge place about
the top edge of T-square.

3. Align the top edge of the paper with T-square blade.
4. Attach the paper’s corners with tape.

5. Move T-square down to smooth the paper.
6. Attach the remaining paper’s corners with tape.

1. Remove the wood with penknife while expose a
lead about 8-10 mm.
2. Polish the lead into a conical shape with a
sandpaper.
3. Clean the lead with tissue paper.
Sharpening the Pencil

Preparing the Compass
2. Adjust the needle and the lead so that the tip of
the needle extends slightly more than the lead.
1. Sharpen the lead with a sandpaper.
needle lead

Straight line
Arc, Circle
4. Circle template
1. T-square
2. Triangles
3. Compass
Tools Shape to be drawn
Function of the Tools

Using the Compass
1. Locate the center of the circle by two intersecting lines.
2. Adjust the distance between needle and lead to a distance
equal to radius of the circle.
3. Set the needle point at center.

4. Start circle. Apply enough pressure to the needle,
holding compass handle between thumb and index fingers.
5. Complete circle. Revolve handle clockwise.
Using the Compass

Using a Circle Template
1. Draw two perpendicular lines that pass through center of
a circle to be drawn.
Construction line
Object line
2. Place the template till all marking coincide with center lines.
3. Tracing the circle. (Hold the pencil normal to the paper.)
Given
Center of a circle to be drawn

Draw a Horizontal Line
1. Press the T-square head against the left edge of the table.
2. Smooth the blade to the right.

Draw a Horizontal Line
3. Lean the pencil at an angle about 60o with the paper in the
direction of the line and slightly “toed in”.
4. Draw the line from left to right while rotating the pencil slowly.

Draw a Vertical Line
1. Set T-square as before. Place any triangle on T-square edge.
2. Slide your left hand to hold both T-square and triangle in
position.

Draw a Vertical Line
3. Lean the pencil to the triangle.
4. Draw the line upward while rotating the pencil slowly.

Draw a line at 45o with horizontal
2. Draw the line in the direction as shown below.
1. Place 45o triangle on the T-square edge and press them
firmly against the paper.

1. Place 30o-60o triangle on the T-square edge and press
them firmly against the paper.
2. Draw the line in the direction as shown below.
Draw a line at angle 30o and 60o

0 deg.
15 deg.
30 deg.
45 deg.
60 deg.
75 deg.
90 deg.
= 30 + 45 deg
Already
demonstrated.
= 30 + 45 deg
Already
demonstrated.
Draw the lines at 15o increment

A
B
Draw the line passing through
two given points
1. Place the pencil tip at one of the points.
2. Place the triangle against the pencil tip.
A
B
Given
3. Swing the triangle around the pencil tip
until its edge align with the second point.
4. Draw a line.

To Bisect a Line
1. Swing two arcs of any radius greater than half-length of
the line with the centers at the ends of the line.
2. Join the intersection points of the arcs with a line.
(not to scale)
A
B
r1
Given
A
B
r1
3. Locate the midpoint.

To Bisect an Angle
2. Swing the arcs of any radius from the intersection
points between the previous arc and the lines.
3. Draw the line.
1. Swing an arc of any radius whose centers at the vertex.
(not to scale)
r1
Given
A
B
C
A
B
C
r2
r2

To draw the line parallel to a given line
and passes through a given point
Given
+
C

and passes through a given point
Given
+
C
Repeat

with a specified distance
Given distance = r
r

r
with a specified distance
Repeat
Given distance = r

To draw the line perpendicular to a
given line at a given point
+
C
Revolve method

+
C
Repeat
Revolve method

+
C
Adjacent-sides method

+
C
Repeat

Using Compass
+
C

Using Compass
r1
+
C
r2
r2 > r1
A
B
D
Repeat

given line from a point not on the line
+
C

+
C
Repeat

Using compass
+ C

Using compass
r2
+ C
r2
r1
Note:
You can also use revolve method. How ? Try by yourself !!!
B
A
D
Repeat

+
C
To draw a line making 15o with a given
line and pass through a given point.
Given

+
C
Given

FILLET AND ROUND
Sharp corner
Fillet
Round
Round

FILLET AND ROUND
To draw the arc, we must find the location of the
center of that arc.
How do we find the center of the arc?

To draw an arc of given radius tangent
to two perpendicular lines
Given arc radius r
r
r

to two perpendicular lines
Given arc radius r
center of the arc
Starting point
Ending point

to two lines
Given arc radius r
+
+
r
r

to two lines
Given arc radius r
T.P.1
T.P.2

C
To draw a line tangent to a circle at a
point on the circle
Given

To draw a line tangent to a circle from
a point outside the circle
Given
C
mark a tangent point

When circle tangent to other circle
C1
C2
Tangent point
R1
R2
The center of two circles and tangent point lie on the same
straight line !!!

To draw a circle tangent to two circles I
+
C2
Given
+
C1
C
+
Example

+
C1
Given Two circles and the radius of the third circle = R
+
C2

+ +
C1
C2
R + R1
R + R2
R1
R2
C
center of the arc
R
Repeat

C2
R2
When circle tangent to other circle
C1
Tangent point
R1
The center of two circles and tangent point must lie on the
same straight line !!!

Given
+
C1
+
C2
C +
To draw a circle tangent to two circles II
Example

+ +
C1
C2

+ +
C1
C2
R – R2
R – R1
R1
R2
C
R
Repeat

+
C1
+C2
To draw a circle tangent to two circles III
R + R2
R – R1
R1
R2
C

To draw an approximate ellipse
Given Major and minor axes

To draw an approximate ellipse
Given Major and minor axes
Repeat

How to Keep Your Drawing Clean
Do Don’t

Chapter 02 Using Drawing Tools.ppt

More Related Content

Similar to Chapter 02 Using Drawing Tools.ppt (20)

More from ImranUnar3 (16)

Recently uploaded (20)

Chapter 02 Using Drawing Tools.ppt