Computer hardware servicing ncii

COMPETENCY-BASED
CURRICULUM
Sector:
INFORMATION AND COMMUNICATION TECHNOLOGY
Qualification:
COMPUTER HARDWARE SERVICING NC II
TECHNICAL EDUCATION AND SKILLS DEVELOPMENT
AUTHORITY
East Service Road, South Superhighway, Taguig City, Metro Manila
Article I.

TABLE OF CONTENTS
Page
A...COURSE DESIGN...................................................................................1-5
B. MODULES OF INSTRUCTION.............................................................6-73
•BASIC COMPETENCIES.........................................................................6
o Participating in workplace communication ………………….......7-10
o Working in a team environment ……………….........................11-13
o Practicing career professionalism .…………….......................14-17
o Practicing occupational health and safety procedures ............18-22
•COMMON COMPETENCIES.............................................................23
o Applying quality standards ……………………………………...24-
27
o Performing computer operations..........................................28-34
o Performing mensuration and calculation..............................35-38
o Preparing and interpreting technical drawing.......................39-42
o Using hand tools...................................................................43-47
o Terminating and connecting electrical wiring and electronics
circuit component.................................................................48-52
•CORE COMPETENCIES........................................................................53
o Installing computer systems and networks ..............................54-58
o Diagnosing and troubleshooting computer system .................59-63
o Configuring computer systems and networks..........................64-67
o Maintaining computer systems and networks ........................68-73

COURSE DESIGN
Course Title : COMPUTER HARDWARE SERVICING NCII
Nominal Duration : 392 hours
Course Description :
This course is designed to develop knowledge, skills, and attitudes of a Computer
Service Technician in accordance with industry standards. It covers basic and common
competencies such as installing, maintaining, configuring, and diagnosing computer
systems and networks.
Entry Requirements:
Candidate/trainee must posses the following qualifications, must be:
• Able to communicate both oral and written
• Physically and mentally fit.
• With good moral character.
• Can perform basic mathematical and logical computations.
• Analytical and logical thinking
CBC Computer Hardware Servicing NC II - 1 -

COURSE STRUCTURE:
BASIC COMPETENCIES
(18 hours)
Units of
Competency
Module Title Learning Outcomes
Nominal
Duration
1. Participate in
workplace
communication
1.1 Participating in
workplace
communication
1.1.1 Obtain and convey workplace
information
1.1.2 Complete relevant work-
related document
1.1.3 Participate in workplace
meeting and discussion
4 hours
2. Work in a team
environment
2.1 Working in a
team
environment
2.1.1 Describe and identify team
role and responsibility
2.1.2 Describe work as a team
member
4 hours
3. Practice career
professionalism
3.1 Practicing
career
professionalis
m
3.1.1 Integrate personal objectives
with organizational goals.
3.1.2 Set and meet work priorities.
3.1.3 Maintain professional growth
and development.
5 hours
4. Practice
occupational
health and
safety
procedures
4.1 Practicing
occupational
health and
safety
procedure
4.1.1 Identify hazards and risks.
4.1.2 Evaluate hazards and risks.
4.1.3 Control hazards and risks.
4.1.4 Maintain occupational health
and safety awareness.
5 hours
- 2 - CBC Computer Hardware Servicing NC II

COMMON COMPETENCIES
(54 hours)
Units of
Competency
Nominal
Duration
1. Apply quality
standards
1.1Applying quality
standards
1.1.1 Assess quality of received
materials
1.1.2 Assess own work
1.1.3 Engage in quality
improvement
9 hours
2. Perform
computer
operations
2.1 Performing
computer
operations
2.1.1 Plan and prepare for tasks
to be undertaken
2.1.2 Input data into computer
2.1.3 Access information using
computer
2.1.4 Produce output/datd using
computer system
2.1.5 Use basic functions of a
web browser to locate
information
2.1.6 Maintain computer
equipment and systems
9 hours
3. Perform
mensuration
and calculation
3.1 Performing
mensuration
and calculation
3.1.1 Select measuring
instruments
3.1.2 Carry out measurements
and calculation
3.1.3 Maintain measuring
instruments
9 hours
4. Prepare and
interpret
technical
drawing
4.1 Preparing and
interpreting
technical
drawing
4.1.1 Identify different kinds of
technical drawings
4.1.2 Interpret technical drawing
4.1.3 Prepare/make changes on
electrical/electronic
schematics and drawings
9 hours
5. Use hand tools 5.1 Using hand
tools
5.1.1 Plan and prepare for tasks
to be undertaken
5.1.2 Prepare hand tools
5.1.3 Use appropriate hand tools
and test equipment
5.1.4 Maintain hand tools
9 hours
6. Terminate and
connect
electrical wiring
and electronics
circuit
6.1 Terminating
and connect
electrical wiring
and electronics
circuit
6.1.1 Plan and prepare for
termination/connection of
electrical wiring/electronics
circuits
6.1.2 Terminate/connect
wiring/electronic circuits
6.1.3 Test
termination/connections of
electrical wiring/electronics
circuits
9 hours

CORE COMPETENCIES
(320 hours)
Units of
Competency
Nominal
Duration
1. Install
computer
systems and
networks
1.1 Installing
computer
systems and
networks
installation
1.1.2 Install equipment/device
system
1.1.3 Conduct test
60 hours
2. Diagnose and
troubleshoot
computer
systems
2.1 Diagnosing and
trouble shooting
computer
systems
diagnosis of faults of
computer systems
2.1.2 Diagnose faults of computer
systems
2.1.3 Repair defects in computer
systems and networks
2.1.4 Test systems and networks
100
hours
3. Configure
computer
systems and
networks
3.1 Configuring
computer
systems and
networks
configuration
3.1.2 Configure computer
3.1.3 Inspect and test configured
computer systems and
networks
100
hours
4. Maintain
computer
systems and
networks
4.1 Maintaining
computer
systems and
networks
4.1.1 Plan and prepare for the
maintenance of computer
4.1.2 Maintain computer systems
4.1.3 Maintain network systems
4.1.4 Inspect and test
configured/repaired
computer system and
networks
60 hours
RESOURCES
Tools Equipment Materials

• Operating System
• Application program
• Components / Dividers
• Oscilloscope
• Rulers
• T-square
• Calculator
• Multi-tester
• Soldering gun
• Pliers
• Cutters
• Screw drivers
• Goggles
• Gloves
• Protractor
• Steel rule
• LAN tester
• Utility softwares
• Anti-static wrist wrap
• Masks
• Crimping tools
• Flashlights
• Sharp pointed tweezers
• Mirror (inspection)
• Soldering gun
• Hubs/switches
• CDROMs
• Modem/router
• Printers
• Hubs
• Server
• Peripherals
• Desktop Computers
• UTP Cat. 5 cables
• UTP Cat.3 cables
• RJ 45 modular plug
• Learning Manuals
• Work Instruction
• Hand-outs
• Board marker
• White board
• Schematic diagrams
• Charts
• Block diagrams
• Layout plans
• Location Plans
• Instrumentation
diagrams
• Loop diagrams
• System Control
diagrams
• Drawing boards

ASSESSMENT METHODS:
• Hands on
• Direct observation
• Practical demonstration
• Oral and written exam
COURSE DELIVERY:
• Lecture-demonstration
• Self-paced instruction
• Group discussion
TRAINER’S QUALIFICTION (TQ II)
• Must be a holder of Computer Hardware Servicing NCIII or equivalent available
qualification
• Must have completed Training METHODOLOGIES II (TM II)
• Must be physically and mentally fit
• *Must have at least 2 years relevant job/industry experience

MODULES OF INSTRUCTION
BASIC COMPETENCIES

BASIC COMPETENCY : COMMUNICATIONS
UNIT OF COMPETENCY : PARTICIPATE IN WORKPLACE COMMUNICATION
MODULE TITLE : PARTICIPATING IN WORKPLACE COMMUNICATION
MODULE DESCRIPTOR : This module covers the knowledge, skills and attitudes
required to obtain, interpret and convey information in
response to workplace requirements.
SUGGESTED DURATION : 4 hours
QUALIFICATION LEVEL : NC II
PREREQUISITE : Receive and Respond to Workplace Communication (NC I)
SUMMARY OF LEARNING OUTCOMES:
Upon completion of this module the students/trainees must be able to:
LO1. Obtain and convey workplace information
LO2. Complete relevant work related documents.
LO3. Participate in workplace meeting and discussion.

LO1. OBTAIN AND CONVEY WORKPLACE INFORMATION
ASSESSMENT CRITERIA:
1. Specific relevant information is accessed from appropriate sources.
2. Effective questioning, active listening and speaking skills are used to gather and
convey information.
3. Appropriate medium is used to transfer information and ideas.
4. Appropriate non-verbal communication is used.
5. Appropriate lines of communication with superiors and colleagues are identified
and followed.
6. Defined workplace procedures for the location and storage of information are
used.
7. Personal interaction is carried out clearly and concisely.
CONTENTS:
• Parts of speech
• Sentence construction
• Effective communication
CONDITIONS:
The students/trainees must be provided with the following:
• Writing materials (pen & paper)
• References (books)
• Manuals
METHODOLOGIES:
• Interaction
• Lecture
• Reportorial
ASSESSMENT METHODS:
• Written test
• Practical/performance test
• Interview

L02. COMPLETE RELEVANT WORK RELATED DOCUMENTS
1. Ranges of forms relating to conditions of employment are completed accurately
and legibly.
2. Workplace data is recorded on standard workplace forms and documents.
3. Basic mathematical processes are used for routine calculations.
4. Errors in recording information on forms/ documents are identified and rectified.
5. Reporting requirements to superior are completed according to enterprise
guidelines.
CONTENTS:
• Basic mathematics
• Technical writing
• Types of forms
CONDITIONS:
• Paper
• Pencils/ball pen
• Reference books
• Manuals
METHODOLOGIES:
• Interaction
• Lecture
ASSESSMENT METHODS:
• Written test
• Interview

LO3. PARTICIPATE IN WORKPLACE MEETINGS AND DISCUSSIONS
1. Team meetings are attended on time.
2. Own opinions are clearly expressed and those of others are listened to without
interruption.
3. Meeting inputs are consistent with the meeting purpose and established
protocols.
4. Workplace interaction are conducted in a courteous manner appropriate to
cultural background and authority in the enterprise procedures.
5. Questions about simple routine workplace procedures and matters concerning
conditions of employment are asked and responded.
6. Meeting outcomes are interpreted and implemented.
CONTENTS:
• Sentence construction
• Technical writing
• Recording information
CONDITIONS:
• Paper
• Pencils/ball pen
• References (books)
• Manuals
METHODOLOGIES:
• Group discussions
• Interaction
• Lecture
ASSESSMENT METHODS:
• Written test
• Interview

UNIT OF COMPETENCY : WORK IN A TEAM ENVIRONMENT
MODULE TITLE : WORKING IN A TEAM ENVIRONMENT
MODULE DESCRIPTOR : This module covers the knowledge, skills, and attitudes
required to relate in a work based environment.
SUGGESTED DURATION : 4 hours
LO1. Describe and identify team role and responsibility in a team.
LO2. Describe work as a team member.

LO1. DESCRIBE AND IDENTIFY TEAM ROLE AND RESPONSIBILITY IN A TEAM
1. Role and objective of the team is identified.
2. Team parameters, relationships and responsibilities are identified.
3. Individual role and responsibilities within team environment are identified.
4. Roles and responsibilities of other team members are identified and recognized.
5. Reporting relationships within team and external to team are identified.
CONTENTS:
• Team role.
• Relationship and responsibilities
• Role and responsibilities with team environment.
• Relationship within a team.
CONDITIONS:
• Standard operating procedure (SOP) of workplace
• Job procedures
• Client/supplier instructions
• Quality standards
• Organizational or external personnel
METHODOLOGIES:
• Group discussion/interaction
• Case studies
• Simulation
ASSESSMENT METHODS:
• Written test
• Observation
• Simulation
• Role playing

LO2. DESCRIBE WORK AS A TEAM MEMBER
1. Appropriate forms of communication and interactions are undertaken.
2. Appropriate contributions to complement team activities and objectives were
made.
3. Reporting using standard operating procedures followed.
4. Development of team work plans based from role team were contributed.
CONTENTS:
• Communication process
• Team structure/team roles
• Group planning and decision making
CONDITIONS:
• SOP of workplace
• Job procedures
• Organization or external personnel
METHODOLOGIES:
• Group discussion/interaction
• Case studies
• Simulation
ASSESSMENT METHODS:
• Observation of work activities
• Observation through simulation or role play
• Case studies and scenarios.

UNIT OF COMPETENCY : PRACTICE CAREER PROFESSIONALISM
MODULE TITLE : PRACTICING CAREER PROFESSIONALISM
MODULE DESCRIPTOR : This module covers the knowledge, skills and attitudes in
promoting career growth and advancement, specifically to
integrate personal objectives with organizational goals set
and meet work priorities and maintain professional growth
and development.
NOMINAL DURATION : 5 hours
LO1. Integrate personal objectives with organizational goals
LO2. Set and meet work priorities
LO3. Maintain professional growth and development

LO1. INTEGRATE PERSONAL OBJECTIVES WITH ORGANIZATIONAL GOALS
1. Personal growth and work plans towards improving the qualifications set for
professionalism are evident.
2. Intra and interpersonal relationship in the course of managing oneself based on
performance evaluation is maintained.
3. Commitment to the organization and its goal is demonstrated in the performance
of duties.
4. Practice of appropriate personal hygiene is observed.
5. Job targets within key result areas are attained.
CONTENTS:
• Personal development-social aspects: intra and interpersonal development
• Organizational goals
• Personal hygiene and practices
• Code of ethics
CONDITIONS:
The students/ trainees must be provided with the following:
• Workplace
• Code of ethics
• Organizational goals
• Hand outs and Personal development-social aspects
• CD’s, VHS tapes, transparencies
METHODOLOGIES:
• Interactive -lecture
• Simulation
• Demonstration
• Self paced instruction
ASSESSMENT METHODS:
• Role play
• Interview
• Written examination

LO2. SET AND MEET WORK PRIORITIES
1. Competing demands to achieve personal, team and organizational goals and
objectives are prioritized.
2. Resources are utilized efficiently and effectively to manage work priorities and
commitments.
3. Practices and economic use and maintenance of equipment and facilities are
followed as per established procedures.
4. Job targets within key result areas are attained.
CONTENTS:
• Organizational key result areas (KRA)
• Work values and ethical standards
• Company policies on the use and maintenance of equipment
CONDITIONS:
The students/ trainees must be provided with the following
• Hand outs on
- Organizational KRA
- Work values and ethics
- Company policies and standards
- Sample job targets
• Learning guides
METHODOLOGIES:
• Interactive lecture
• Structured activity
• Demonstration
ASSESSMENT METHODS:
• Role play
• Interview

LO3. MAINTAIN PROFESSIONAL GROWTH AND DEVELOPMENT
1. Training and career opportunities relevant to the job requirements are identified
and availed.
2. Licenses and/or certifications according to the requirements of the qualifications
are acquired and maintained
3. Fundamental rights at work including gender sensitivity are manifested/ observed
4. Training and career opportunities based on the requirements of industry are
completed and updated.
CONTENTS:
• Qualification standards
• Gender and development (GAD) sensitivity
• Professionalism in the workplace
• List of professional licenses
CONDITIONS:
The students/trainees must be provided with the following
• Quality standards
• GAD handouts
• CD’s, VHS tapes on professionalism in the workplace
• Professional licenses samples
METHODOLOGIES:
• Film viewing
• Role play/simulation
ASSESSMENT METHODS:
• Demonstration
• Interview
• Portfolio assessment

UNIT OF COMPETENCY : PRACTICE OCCUPATIONAL HEALTH AND SAFETY
PROCEDURES
MODULE TITLE : PRACTICING OCCUPATIONAL HEALTH AND SAFETY
PROCEDURES
MODULE DESCRIPTOR : This module covers the knowledge, skills and attitudes
required to comply with the regulatory and organizational
requirements for occupational health and safety such as
identifying, evaluating and maintaining occupational health
and safety (OHS) awareness.
LO1. Identity hazards and risks
LO2. Evaluate hazards and risks
LO3. Control hazards and risks
LO4. Maintain occupational health and safety awareness

LO1. IDENTIFY HAZARDS AND RISKS
1. Workplace hazards and risks are identified and clearly explained.
2. Hazards/risks and its corresponding indicators are identified in with the company
procedures.
3. Contingency measures are recognized and established in accordance with
organizational procedures.
CONTENTS:
• Hazards and risks identification and control
• Organizational safety and health protocol
• Threshold limit value (TLV)
• OHS indicators
CONDITIONS:
• Workplace
• Personal protective equipment (PPE)
• Learning guides
• Hand-outs
- Organizational safety and health protocol
- OHS indicators
- Threshold limit value
- Hazards/risk identification and control
METHODOLOGIES:
• Interactive -lecture
• Simulation
• Symposium
• Group dynamics
ASSESSMENT METHODS:
• Situation analysis
• Interview
• Practical examination

LO2. EVALUATE HAZARDS AND RISKS
1. Terms of maximum tolerable limits are identified based on threshold limit values
(TLV)
2. Effects of hazards are determined.
3. OHS issues and concerns are identified in accordance with workplace
requirements and relevant workplace OHS legislation.
CONTENTS:
• TLV table
• Philippine OHS standards
• Effects of hazards in the workplace
• Ergonomics
• ECC Regulations
CONDITIONS:
• Hand outs on
- Philippine OHS standards
- Effects of hazards in the workplace
- Ergonomics
- ECC regulations
• TLV table
METHODOLOGIES:
• Situation analysis
• Symposium
• Film viewing
• Group dynamics
ASSESSMENT METHODS:
• Interview
• Simulation

LO3. CONTROL HAZARDS AND RISKS
1. OHS procedures for controlling hazards and risk are strictly followed.
2. Procedures in dealing with workplace accidents, fire and emergencies are
followed in accordance with the organization’s OHS policies.
3. Personal protective equipment (PPE) is correctly used in accordance with
organization’s OHS procedures and practices.
4. Procedures in providing appropriate assistance in the event of workplace
emergencies are identified in line with the established organizational protocol.
CONTENTS:
• Safety regulations
- Clean air act
- Electrical and fire safety code
- Waste management
- Disaster preparedness and management
• Contingency measures and procedures
CONDITIONS:
• Hand outs on
- Safety Regulations
- Clean air act
- Electrical and fire safety code
- Waste management
- Disaster preparedness and management
- Contingency measures and procedures
• OHS personal records
• PPE
METHODOLOGIES:
• Symposium
• Film viewing
• Group dynamics
ASSESSMENT METHODS:
• Interview
• Case/situation analysis
• Simulation

LO4. MAINTAIN OCCUPATIONAL HEALTH AND SAFETY AWARENESS
1. Procedures in emergency related drill are strictly followed in line with the
established organization guidelines and procedures.
2. OHS personal records are filled up in accordance with workplace requirements.
3. PPE are maintained in line with organization guidelines and procedures.
CONTENTS:
• Operational health and safety procedure, practices and regulations
• Emergency-related drills and training
CONDITIONS:
• Workplace
• PPE
• OHS personal records
• Health record
METHODOLOGIES:
• Simulation
• Symposium
• Film viewing
• Group dynamics
ASSESSMENT METHODS:
• Demonstration
• Interview
• Portfolio assessment

COMMON COMPETENCIES

UNIT OF COMPETENCY : APPLY QUALITY STANDARDS
MODULE TITLE : APPLYING QUALITY STANDARDS
MODULE DESCRIPTION : This module covers the knowledge, skills, attitudes and
values needed to apply quality standards in the workplace.
The unit also includes the application of relevant safety
procedures and regulations, organization procedures and
customer requirements.
LO1. Assess quality of received materials
LO2. Assess own work
LO3. Engage in quality improvement

LO1. ASSESS QUALITY OF RECEIVED MATERIALS
1. Work instruction obtained and work carried out in accordance with standard
operating procedures.
2. Received materials checked against workplace standards and specifications.
3. Faulty materials related to work are identified and isolated
4. Faults and any identified causes recorded and or reported to the supervisor
concerned in accordance with workplace procedures
5. Faulty materials are replaced in accordance with workplace procedures
CONTENTS:
• Reading skills required to interpret work instruction
• Workplace standards and specifications
• Procedures in obtaining and carrying out work instructions
• Quality checking procedures
• Fault identification and reporting
• Safety and environmental aspects of production process
• Carry out work in accordance with policies and procedures
CONDITIONS:
• Work instructions
• Manuals (operation manual of the company/manufacturer’s instruction/service
manual)
• Company/workplace standards and specifications
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO2. ASSESS OWN WORK
1. Documentation relative to quality within the company identified and used
2. Completed work checked against workplace standards and specifications
3. Errors are identified and isolated
4. Information on the quality and other indicators of production procedures recorded
in accordance with workplace procedures
5. In cases of deviation from specific quality standards, causes documented and
reported in accordance with the workplace’s standard operating procedures.
CONTENTS:
• Communication skills needed to interpret and apply defined work procedures
• Identifying errors (deviation from customer and or organization requirements)
CONDITIONS:
• Organization work procedures
• Manufacturer’s Instruction Manual
• Customer requirements
• Other forms
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO3. ENGAGE IN QUALITY IMPROVEMENT
1. Process improvement procedures participated in relative to workplace
assignment
2. Work carried out in accordance with process improvement procedures
3. Performance of operation or quality of product of service to ensure customer
satisfaction monitored
CONTENTS:
• Relevant production processes, materials and products
• Safety and environmental aspects of production processes
• Critical thinking
• Quality improvement processes
CONDITIONS:
• Organization work procedures
• Manufacturer’s Instruction Manual
• Customer requirements
• Other forms
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

UNIT OF COMPETENCY : PERFORM COMPUTER OPERATIONS
MODULE TITLE : PERFORMING COMPUTER OPERATIONS
MODULE DESCRIPTION : This module covers the knowledge, skills, attitudes and
values needed to perform computer operations which include
inputting, accessing, producing, and transferring data using
the appropriate hardware and software.
LO1. Plan and prepare for tasks to be taken/undertaken
LO2. Input data into computer
LO3. Access information using computer
LO4. Produce output/data using computer systems
LO5. Use basic functions of a Web browser to locate information
LO6. Maintain computer equipment and systems

LO1. PLAN AND PREPARE FOR TASKS TO BE UNDERTAKEN
1. Requirements of tasks determined in accordance with the required output
2. Appropriate hardware and software selected according to task assigned and
required outcome
3. Task planned to ensure that OH and S guidelines and procedures followed
4. Client-specific guidelines and procedures followed
5. Required data security guidelines applied in accordance with existing procedures
CONTENTS:
• Reading and comprehension skills required to interpret work instructions and to
interpret basic user manuals
• OH and S principles and responsibilities
• Main types of computers and basic features of different operating systems
• Main parts of a computer
• Storage devices and basic categories of memory
• Relevant types of software
• General security, privacy legislation and copyright
CONDITIONS:
• Equipment:
- 1 unit of computer
- voltage regulator/UPS
• Learning Materials:
- Learning manuals
- Work instruction
- Hand-outs
• Supplies/materials:
- Operating system
- Application program
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO2. INPUT DATA INTO COMPUTER
1. Data entered into the computer using appropriate program/application in
accordance with company procedure
2. Accuracy of information checked and information saved in accordance with
standard operating procedures
3. Inputted data stored in storage media according to requirements
4. Work performed within ergonomic guidelines
CONTENTS:
• Communication skills to identify lines of communication, request advice, follow
instructions and receive feedback
• Basic ergonomics of keyboard and computer user
CONDITIONS:
• Equipment:
- Learning manuals
- Work instruction
- Hand-outs
• Supplies/Materials:
- Operating system
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO3. ACCESS INFORMATION USING COMPUTER
1. Correct program/application selected based on job requirements
2. Program/application containing the information required accessed according to
company procedures
3. Desktop icons correctly selected, opened and closed for navigation purposes
4. Keyboard techniques carried out in line with OHS requirements for safe use of
keyboards
CONTENTS:
• Business application
• System software
• Basic ergonomics of keyboard and computer user
CONDITIONS:
• Equipment:
- Learning manuals
- Work instruction
- Hand-outs
- Operating system
- Disks
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO4. PRODUCE OUTPUT/DATA USING COMPUTER SYSTEM
1. Entered data processed using appropriate software commands
2. Data printed as required using computer hardware/peripheral devices in
accordance with standard operating procedures
3. Files and data transferred between compatible systems using computer software,
hardware/peripheral devices in accordance with standard operating procedures
CONTENTS:
• Computer peripherals
CONDITIONS:
• Equipment:
- printer
- Learning manuals
- Work instruction
- Hand-outs
- Operating system
- Disks
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO5. USE BASIC FUNCTIONS OF A WEB BROWSER TO LOCATE INFORMATION
1. Information requirements for Internet search established
2. Browser launched
3. Search engine loaded
4. Appropriate search criteria and/or URL of site entered
5. Relevant links followed to locate required information
6. Useful pages bookmarked or printed as required
CONTENTS:
• Web surfing
• Web browsers
• Search engines
• URLS and keywords
• Links
• Bookmarking
CONDITIONS:
• Equipment:
- Learning manuals
- Work instruction
- Hand-outs
- Operating system
- Disks
- Paper
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO6. MAINTAIN COMPUTER EQUIPMENT AND SYSTEMS
1. Procedures for ensuring security of data, including regular back-ups and virus
checks implemented in accordance with standard operating procedures
2. Basic file maintenance procedures implemented in line with standard operating
procedures
CONTENTS:
• Security measures
• Anti-virus software/programs
• File Management
CONDITIONS:
• Equipment:
- Learning manuals
- Work instruction
- Hand-outs
- Operating system
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

UNIT OF COMPETENCY : PERFORM MENSURATION AND CALCULATION
MODULE TITLE : PERFORMING MENSURATION AND CALCULATION
MODULE DESCRIPTION : This unit covers the knowledge, skills and attitudes and
values needed identify, care, and use measuring
instruments.
LO1. Select measuring instruments
LO2. Carry out measurements and calculation
LO3. Maintain measuring instruments

LO1. SELECT MEASURING INSTRUMENTS
1. Object or component to be measured identified
2. Correct specifications obtained from relevant source
3. Measuring tools selected in line with job requirements
CONTENTS:
• Types of components and object to be identified
• Knowing the correct specifications of the relevant sources
• Identify the necessary measuring tools in selecting the job requirements
• Communication skills
CONDITIONS:
• Try square
• Protractor
• Steel rule
• Taper
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO2. CARRY OUT MEASUREMENTS AND CALCULATION
1. Appropriate measuring instrument selected to achieve required outcome.
2. Accurate measurements obtained for job.
3. Calculation needed to complete work tasks are performed using the four
fundamentals operations (addition, subtractions, multiplication and division)
4. Calculation involving fractions, percentages, and mixed numbers used to
complete workplace tasks.
5. Instruments read to the limit of accuracy of the tool.
CONTENTS:
• Identifying appropriate measuring instruments to be used.
• Use accurate measurements for the tasks given.
• Using the four fundaments of mathematical operations
• Introducing proper procedure in calculating fractions, percentages, and mixed
numbers to perform in the given tasks.
CONDITIONS:
• Torque gauge
• Combination gauge
• Volume
• Area
• Circumference
• Thickness
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO3. MAINTAIN MEASURING INSTRUMENTS
1. Measuring instruments not dropped to avoid damage.
2. Measuring instruments cleaned before and after using.
3. Proper storage of instruments undertaken according to the manufacturer’s
specifications and standard operating procedures.
CONTENTS:
• Using appropriate instruments tools to avoid damage.
• Proper procedure in cleaning up the workplace before and after using
• Identifying the proper storage of the instruments to be kept that met the
manufacturer’s specifications and standard to avoid damage in mismatching.
CONDITIONS:
• Straight edge
• Steel rule
• Displacement
• Inside diameter
• Outside diameter
• Thickness
• Taper
• Out of roundness
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

UNIT OF COMPETENCY : PREPARE AND INTERPRET TECHNICAL DRAWING
MODULE TITLE : PREPARING AND INTERPRETING TECHNICAL
DRAWING
MODULE DESCRIPTION : This module covers the knowledge, skills and attitude and
values needed to prepare/interpret diagrams, engineering
abbreviation and drawings, symbols and dimensions
LO1. Identify different kinds of technical drawings
LO2. Interpret technical drawing
LO3. Prepare/make changes on electrical/electronic schematics and drawings

LO1. IDENTIFY DIFFERENT KINDS OF TECHNICAL DRAWINGS
1. Correct technical drawing selected according to job requirements
2. Technical drawings segregated in accordance with the types and kinds of
drawings.
CONTENTS:
• Drawing conventions
• Symbols
• Dimensioning conventions
• Markup/notation of drawings
CONDITIONS:
• Charts
• Block diagrams
• Layout plans
• Location plans
• Process and Instrumentation diagrams
• Loop diagrams
• System control diagrams
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO2. INTERPRET TECHNICAL DRAWING
1. Components, assemblies or objects recognized as required
2. Dimensions of the key features of the objects depicted in the drawing correctly
identified
3. Symbols used in the drawing identified and interpreted correctly
4. Drawing checked and validated against job requirements or equipment in
accordance with standard operating procedures
CONTENTS:
• Reading skills required to interpret work instructions
• Skills in interpreting electrical / electronic signs and symbols
CONDITIONS:
• Charts
• Block diagrams
• Layout plans
• Location Plans
• Process and Instrumentation diagrams
• Loop diagrams
• System Control diagrams
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO3. PREPARE/MAKE CHANGES ON ELECTRICAL/ELECTRONIC SCHEMATICS
AND DRAWINGS
1. Electrical/ Electronic schematic drawn and correctly identified
2. Correct drawing identified, equipment selected and used in accordance with job
requirements
CONTENTS:
• Mathematics
CONDITIONS:
• Components/dividers
• Drawing boards
• Rulers
• T-square
• Calculator
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

UNIT OF COMPETENCY : USE HAND TOOLS
MODULE TITLE : USING HAND TOOLS
MODULE DESCRIPTION : This unit covers the knowledge, skills and attitudes on the
safe use, handling and maintenance of tools.
LO1. Plan and prepare for tasks to be undertaken
LO2. Prepare hand tools
LO3. Use appropriate hand tools and test equipment
LO4. Maintain hand tools

LO1. PLAN AND PREPARE FOR TASKS TO BE UNDERTAKEN
1. Tasks to be undertaken properly identified.
2. Appropriate hand tools identify
3. Hand tools selected according to the task requirements
CONTENTS:
• Identifying appropriate hand tools
• Identifying tasks
• Selecting appropriate hand tools
CONDITIONS:
• Hand tools for adjusting, dismantling, assembling, finishing, cutting, screwdrivers,
pliers, punches
• Wrenches
• files
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO2. PREPARE HAND TOOLS
1. Appropriate hand tools checked for proper operation and safety
2. Unsafe or faulty tools identified
3. Marked all tools for repair according to standard company procedures
CONTENTS:
• Operation of hand tools
• Function of hand tools
• Common faults of hand tools
• Safety requirements of hand tools
• Preparing tools
CONDITIONS:
• Hand tools for adjusting, dismantling, assembling, finishing, cutting,
• Tool set ( screwdrivers, pliers, punches, wrenches, files)
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO3. USE APPROPRIATE HAND TOOLS AND TEST EQUIPMENT
1. Tools used according to tasks undertaken
2. All safety procedures in using tools observed at all times
3. Malfunctions, unplanned or unusual events reported to the supervisor
CONTENTS:
• Function of tools
• Safety requirements of tools
• Proper used of tools
• Creating report for malfunctions, unplanned or unusual events
CONDITIONS:
• Cleaning
• Lubricating
• Tightening
• Simple tool repairs
• Hand sharpening
• Adjustment using correct procedures
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO4. MAINTAIN HAND TOOLS
1. Tools used according to tasks undertaken
2. Routine maintenance of tools undertaken according to standard operational
procedures, principles and techniques
3. Tools stored safely in appropriate locations in accordance with manufacturers
specifications or standard operating procedures
CONTENTS:
• Maintenance of tools
• Storage of tools
• Standard operational procedures, principles and techniques in maintaining a tools
CONDITIONS:
• Cleaning
• Lubricating
• Tightening
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

UNIT OF COMPETENCY : TERMINATE AND CONNECT ELECTRICAL WIRING AND
ELECTRONICS CIRCUIT
MODULE TITLE : TERMINATING AND CONNECTING ELECTRICAL WIRING
AND ELECTRONICS CIRCUIT COMPONENT
MODULE DESCRIPTION : This unit covers the knowledge, skills and attitudes and
values needed to terminate and connect electrical wiring and
electronic circuits.
LO1. Plan and prepare for termination/connection of electrical wiring/electronics circuits
LO2. Terminate/connect wiring/electronic circuits
LO3. Test termination/connections of electrical wiring/electronics circuits

LO1. PLAN AND PREPARE FOR TERMINATION/CONNECTION OF ELECTRICAL
WIRING/ELECTRONICS CIRCUITS
1. Materials checked according to specification and tasks
2. Appropriate tools and equipment selected according to tasks requirements
3. Task is planned to ensure OH & S guidelines and procedures followed.
4. Electrical wiring/electronic, circuits correctly prepared for connecting/termination
in accordance with instructions and worksite procedures.
CONTENTS:
• Identified the materials needed to perform the given specification
• Used appropriate tools and equipment as required in the given tasks
• Prior planning to perform the specific guidelines and procedures
• Ensuring the accuracy and correctness of electrical/wiring and electronics
connections to be used and placed in the worksite.
CONDITIONS:
• Materials
• Soldering lead
• Toots and equipment
• Pliers
• Personal Protective Equipment
• Goggles
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO2. TERMINATE/CONNECT WIRING/ELECTRONIC CIRCUITS
1. Safety procedures in using tools observed at all times and appropriate personal
protective equipment used
2. All works undertaken safety in accordance with the workplace and standard
procedures.
3. Appropriate ranges of methods in termination/connection used according to
specifications, manufacturer’s requirements and safety.
4. Correct sequence of operation followed
5. Accessories used adjusted, if necessary
6. Confirm termination/connections undertaken successfully in accordance with job
specification.
CONTENTS:
• Provide necessary safety procedures in using tools and appropriate protective
equipment in the worksite.
• Tasks given are based to standards procedures in accordance with the safety
requirements.
• Identifying appropriate methods in terminating connection are according to
prescribed standards.
• Using proper sequence of operation
• Jobs performance must be in accordance with the standard procedures.
CONDITIONS:
• Materials
- Cables
- Soldering lead
- Wires
• Tools and equipment
- Pliers
- Cutters
- Screw drivers
- Soldering gun
- Multi-tester
• Personal protective equipment
- Goggles
- Gloves

METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO3. TEST TERMINATION/CONNECTIONS OF ELECTRICAL WIRING/ELECTRONICS
CIRCUITS
1. Testing of all completed termination/connections of electric wiring/electronic
circuits conducted for compliance with specification and regulations using
appropriate procedures and equipment
2. Wiring and circuits checked using specified testing procedures
3. Unplanned events or conditions responded to in accordance with established
procedures.
CONTENTS:
• Using of appropriate tools in testing of the different circuits connected to ensure
the validity and conformity of the connection
• Identify the accurate tools to checked the specified wiring circuits
• Responding as compliance with the standard established procedures
CONDITIONS:
• Materials
- Cables
- Soldering lead
- Wires
• Tools and equipment
- Pliers
- Cutters
- Screw drivers
- Soldering gun
- Multi-tester
- Goggles
- Gloves
METHODOLOGIES:
ASSESSMENT METHOD:
• Hands-on

CORE COMPETENCIES

UNIT OF COMPETENCY : INSTALL COMPUTER SYSTEMS AND NETWORKS
UNIT MODULE : INSTALLING COMPUTER SYSTEMS AND NETWORKS
MODULE DESCRIPTOR : This module covers the outcomes required in installing,
assembling and testing computers and common peripherals
PREREQUISITE : NC I
LO1. Plan and prepare for installation
LO2. Install equipment/device system
LO3. Conduct test

LO1. PLAN AND PREPARE FOR INSTALLATION
1. Installation planned and prepared to ensure that safety measures, policies and
procedures followed, and that work is appropriately sequenced in accordance
with the industry standards
2. Technical personnel consulted to ensure that the work coordinated effectively
with others involved on the worksite
3. Computer systems and network devices obtained in accordance with the
established procedures and to comply with requirements
4. Location where devices and systems to be installed is determined from job
requirements
5. Materials necessary to complete the work obtained in accordance with
established procedures and checked against job requirements
6. Tools, equipment and testing devices needed to carry out the installation work
obtained in accordance with established procedures and checked for correct
operation and safety
7. Preparatory work checked to ensure that no unnecessary damage has occurred
and that work complies with requirements
CONTENTS:
• Safety procedures
• Basic terms, concepts, functions and characteristics of PC hardware components
• Structure of operating systems
• Familiarization with the various computer systems’ components and peripherals
• system configuration/ settings of computer systems and devices
CONDITIONS:
• Personal Protective equipment ( ex. protective eyewear, anti static wrist wrap)
• Electronic laboratory hand tools (assorted pliers, assorted screw drivers,
soldering iron & desoldering tool)
• LAN tester
• Crimping tools
• RS 232 pin exertion/ extraction tool
• Flashlights
• Hand-outs
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO2. INSTALL DEVICE/SYSTEM/EQUIPMENTS
1. Occupational health and safety policies and procedures followed in installing
computer systems , network devices, and peripherals
2. Computer systems, network devices and peripherals installed obtained in
accordance with the established procedures and to comply with requirements
3. Appropriate procedures in installing computer systems, network devices and
peripherals achieve in accordance with requirements without damage or
distortion to the surrounding environment and services
4. Variation to devices/systems installation carried out in accordance with the
customer/client’s requirements
5. Unplanned events or conditions responded to in accordance to in accordance
with established procedures
6. Approval is obtained in accordance with established procedures from appropriate
personnel before any contingencies implemented
7. On going checks of the quality of the quality of the work undertaken in
accordance with the established procedures
CONTENTS:
• Basic computer configuration set up
• System’s specifications
• Identifying common symptoms and problems associated with each devices
• Troubleshooting and isolating PC hardware problems
• Diagnosing and troubleshooting hardware conflicts
• Knowledge in installing peripherals, network devices and other I/O devices
CONDITIONS:
soldering iron, desoldering tool)
• LAN tester
• Crimping tools
• Flashlights
• Device drivers , operating system
• Appropriate software application programs
• Diagnostic software or utilities
• Hand-outs
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO3. CONDUCT TEST
1. Occupational health and safety policies and procedures for installing computer
systems and network devices followed.
2. Circuits and systems checked as being isolated where necessary using specified
testing procedures
3. Parts or connections of the installation or service that removed in order to
conduct the test stored to protect against loss or damage and in accordance with
established procedures
4. Unplanned events or conditions responded to in accordance with the industry
requirements
5. Approval obtained in accordance with established procedures from appropriate
personnel before any contingencies are implemented
6. Devices/systems and/or installation tested to terminated in accordance with the
industry requirements
7. Parts and/or connections removed for testing returned to pre-test conditions in
accordance with established procedures
8. Final inspections undertaken to ensure that the installed devices/systems
conforms to requirements
9. Documents in relation to the test forwarded to appropriate personnel and/or
authority in accordance with requirements
CONTENTS:
• Basic computer configuration set up
• Understanding and comparing various system’s specifications
• Identifying common symptoms and problems
• Troubleshooting and isolating problems
• Diagnosing and troubleshooting conflicts
• Installing peripherals, network devices and other I/O devices
• Knowledge in performing burn-in or testing repaired or replaced network system
CONDITIONS:
soldering iron, desoldering tool)
• LAN tester
• Crimping tools
• Flashlights
• Sharp pointed tweezers
• Hand-outs

METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

UNIT OF COMPETENCY : DIAGNOSE AND TROUBLESHOOT COMPUTER SYSTEM
MODULE TITLE : DIAGNOSING AND TROUBLESHOOTING COMPUTER
SYSTEM
MODULE DESCRIPTOR : This unit covers the knowledge, skills and attitudes needed
to diagnose computer systems and networks
QUALIFICATION LEVEL : NCII
LO1. Plan and prepare for diagnosis of faults of computer systems
LO2. Diagnose faults of computer systems
LO3. Repair defects in computer systems and networks
LO4. Test systems and networks

LO1. PLAN AND PREPARE FOR DIAGNOSIS OF FAULTS OF COMPUTER
SYSTEMS
1. Faults and error of computer system properly determined.
2. Tools (hardware/software) identified in accordance with its uses and functions.
3. Safety precautions established in accordance with workplace procedures.
CONTENTS:
• Different types of computer systems error.
• Software as tools for diagnosing computer systems.
• Hand tools and its uses.
• Procedures in diagnosing computer systems
• Safety precautions
CONDITIONS:
• Tools:
- Screw drivers (assorted)
- Pliers (assorted)
- Soldering iron
- Wrenches
- Utility software
- Computer system
• Policies and procedures:
- Procedures and guidelines
- Safety precautions
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO2. DIAGNOSE FAULTS OF COMPUTER SYSTEM
1. Components or parts of computer system clearly identified
2. Functions of the computer systems explained
3. Faults and failures of the computer systems diagnosed base on the job
requirements
CONTENTS:
• Parts and functions of computer system
• Software (operating system, application software)
• Electrical theory
• Computer monitors
• Techniques for diagnosing computer system
CONDITIONS:
• Tools:
- Pliers (assorted)
- Wrenches
- Utility software
• Materials:
- Connectors
- Adaptors
- Diskettes
- CD ROM
• Computer system:
- Complete set of working computer
- Spare of all components
• Testing devices:
- Multi-meter
- Oscilloscope
- Appropriate software
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO3. REPAIR DEFECTS IN COMPUTER SYSTEMS AND NETWORKS
1. Defective components properly replaced and corrected
2. Error in networks clearly identified and repaired in line with standard procedures
3. Defective components identified and separated to other components
CONTENTS:
• Proper repairing/replacing procedures of different components
• Wiring techniques
• Power supplies
• Determining defective components
• Basic networking
CONDITIONS:
• Tools:
- Pliers (assorted)
- Soldering iron
- Wrenches
- Utility software
- Crimping tools
- Servers
- Workstations
- Printers
- Procedures and guidelines
- Multi-tester
- Oscilloscope
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO4. TEST SYSTEMS AND NETWORKS
1. Computer systems and networks are tested in accordance with the job
requirements
2. Information are shared from one computer to another as primary requirement in
computer networking
3. Reports are prepared and completed according to the company requirements
CONTENTS:
• Guidelines for testing computer system
• Advance networking
• Computer systems operation
• Digital electronics
• Communications
CONDITIONS:
- Servers
- Workstations
- Printers
- Procedures and guidelines for testing
- Network cable tester
- Hubs
• Others:
- Papers (for report generation)
- AC line (to supply power)
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

UNIT OF COMPETENCY : CONFIGURED COMPUTER SYSTEMS AND NETWORKS
MODULE TITLE : CONFIGURING COMPUTER SYSTEMS AND NETWORKS
MODULES DESCRIPTOR : This unit covers the knowledge, skills and attitudes needed
to configure computer systems and networks
CERFICATION LEVEL : NC II
LO1. Plan and prepare for configuration
LO2. Configure computer systems and networks
LO3. Inspect and test configured computer systems and networks

LO1. PLAN AND PREPARE FOR CONFIGURATION
1. Configured computer systems and networks identified from the Job/Service Order
or instructions.
2. Planned and prepared job requirements.
3. Followed OHS policies and procedures of job requirements.
4. Checked computer systems and networks configuration with specified
requirements.
5. Checked necessary tools, equipment materials
CONTENTS:
• Inspecting work instructions according to job requirements.
• Planning and preparing of standard operating procedures
• Occupational health and safety
• Configuring system and networks
• Procedures in using the tools and equipments
CONDITIONS:
• OH & S policies and procedures
- OH & S policies
- manuals
• Computer systems and networks
- 1 Server
- Peripherals
- 1 Desktop Computers
• Materials
- Wires and Cables
- Appropriate Software
- Computer Storage Media
• Tools
- Pliers
- Philips screw driver
• Equipment/testing devices
- Computer
- Anti-static wrist wrap
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on application

LO2. CONFIGURE COMPUTER SYSTEMS AND NETWORKS
1. Appropriate Personal Protective Equipment are used and OHS policies and
procedures followed
2. Normal function of systems and networks checked in accordance with
manufacturer’s instructions
3. Fault or problem in the systems and networks diagnosed in line with the standard
operating procedures.
4. Computer systems and networks configured in line with the standard operating
procedures.
CONTENTS:
• Testing normal function of systems and networks
• Procedures in checking the faults or problems
• Procedures in configure systems and networks
CONDITIONS:
- OH & S policies
- manuals
- 1 Server
- Peripherals
• Materials
- Wires and Cables
• Tools
- Pliers
- Computer
METHODOLOGIES:
ASSESSMENT METHODS:

LO3. INSPECT AND TEST CONFIGURED COMPUTER SYSTEMS AND NETWORKS
1. Final inspections are undertaken to ensure that the configuration done on the
systems and networks conforms with the manufacture’s instruction/manual
2. Computer systems and networks are checked to ensure safe operation.
3. Report is prepared and completed according to company requirements.
CONTENTS:
• Inspection of systems and networks with manuals
• Making documents and reports
CONDITIONS:
- OH & S policies
- Manuals
- 1 Server
- Peripherals
• Materials
- Wires and Cables
• Tools
- Pliers
- Computer
METHODOLOGIES:
• Group Discussion
ASSESSMENT METHODS:
• Practical Demonstration

UNIT OF COMPETENCY : MAINTAIN COMPUTER SYSTEMS AND NETWORK
MODULE TITLE : MAINTAINING COMPUTER SYSTEMS AND NETWORKS
MODULE DESCRIPTOR : This module covers the knowledge, skills and attitude
needed to maintain computer systems and networks
LO1. Plan and prepare for the maintenance of computer systems and networks.
LO2. Maintain computer systems
LO3. Maintain network systems
LO4. Inspect and test configured/repaired computer system and networks

LO1. PLAN AND PREPARE FOR THE MAINTENANCE OF COMPUTER SYSTEMS
AND NETWORKS.
1. Maintenance planned and prepared with OHS policies and procedures.
2. The materials, tools, equipments and testing devices obtained and checked.
3. Computer systems and networks checked, identified and maintained with
specifications and requirements to conform with manufacturers.
CONTENTS:
• Plan/conduct maintenance procedures according to job requirements.
• Safety measures are observed at all times.
• Identify and diagnose faulty system.
• Prepare tools and test equipments.
• Identify or obtain PC specifications and schematic diagrams.
• Identify or obtain Network functions and specifications.
CONDITIONS:
• OHS guidelines and policies.
• PC specifications
• Network designs
• Schematic Diagrams
• Books/magazines
• Manuals
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO2. MAINTAIN COMPUTER SYSTEMS
1. The normal functions of computer systems are checked and tested.
2. The scheduled/periodic maintenance and cleaning are performed.
3. The repairs/replacements and sudden breakdowns responded in accordance with
established procedures.
CONTENTS:
• Procedures in maintaining computer systems are followed
• Safety measures are observed.
• Diagnose and identify faulty systems.
• Run diagnostics software.
• Repair or replace faulty system
• Burn-in or test repaired or replaced computer system
CONDITIONS: The students/trainees must be provided with the following:
• PC specification
• Personal protective equipments
- Gloves and goggles
- Masks
- Anti-static wrist wraps
• Materials
- Contact cleaners/ soap or detergents
- Dust brush
- Chamois or rags
- Basin/ water
• Diagnostics software and CD-ROMs
• Tools and test equipments
- Slotted head screwdriver
- Philips head screwdriver
- Long nosed pliers
- Allen bit wrench
- Multi-tester
• Spare parts
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO3. MAINTAIN NETWORK SYSTEMS
1. The normal functions of network systems checked and tested.
2. The scheduled/periodic maintenance and cleaning performed.
3. The repairs/replacements and sudden breakdowns responded in accordance with
established procedures.
CONTENTS:
• Procedures in maintaining network systems are followed
• Safety measures are observed.
• Diagnose and identify faulty systems and cables.
• Run diagnostics software.
• Repair or replace faulty systems and cables.
• Burn-in or test repaired or replaced network system.
CONDITIONS: The students/trainees must be provided with the following:
• PC and network specification
• Network Cables and peripherals
- UTP Cat. 5 cables
- UTP Cat.3 cables
- RJ 45 modular plug
- Hubs/switches
- Modem/router
• Network layout and schematic diagrams
• Personal protective equipments
- Gloves and goggles
- Masks
- Anti-static wrist wraps
• Materials
- Contact cleaners/ soap or detergents
- Dust brush
- Chamois or rags
- Basin/ water
• Diagnostics software and CDROMs
- Long nosed pliers
- Allen bit wrench
- Crimping tool
- Cable tester
- Multi-tester
- Spare cables

METHODOLOGIES:
ASSESSMENT METHODS:
• Hands-on

LO4. INSPECT AND TEST CONFIGURED/REPAIRED COMPUTER SYSTEM
AND NETWORKS
1. Computer system and network checked to ensure safe operation.
2. Final inspection and testing taken to conform with manufacturer specifications.
3. Reports prepared and completed to company regulations.
CONTENTS:
• Check the maintained/serviced computer systems to ensure safe operation.
• Run or conduct computer to computer communications.
• Connect to the internet if necessary.
• Burn-in serviced or replaced components.
• Return computer to networking area.
• Document the task undertaken.
CONDITIONS:
• PC specification
• Diagnostics software and CDROMs
• Books/manuals/magazines
- Long nosed pliers
- Allen bit wrench
METHODOLOGIES:
ASSESSMENT METHODS:
• Hands on
• Oral and written exam

What is Competency-Based Curriculum (CBC)
 A competency-based curriculum is a framework or guide for the
subsequent detailed development of competencies, associated
methodologies, training and assessment resources.
 The CBC specifies the outcomes which are consistent with the
requirements of the workplace as agreed through the industry or
community consultations.
 CBC can be developed immediately when competency standards exist.
 When competency standards do not exist, curriculum developers need
to clearly define the learning outcomes to be attained. The standard of
performance required must be appropriate to industry and occupational
needs through the industry/enterprise or specified client group
consultations.
These materials are available in both printed and electronic copies.
For more information please contact:
Technical Education and Skills Development Authority
(TESDA)
Telephone Nos.: 893-8281, 817-4076 to 82 loc. 611, 630, 631 and 635 or
visit our website: www.tesda.gov.ph or the TESDA Regional or Provincial
Office nearest you.

Computer hardware servicing ncii

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Computer hardware servicing ncii (20)

Recently uploaded (20)

Computer hardware servicing ncii