Conditional Averaging a New Algorithm for Digital Filter

ACEEE Int. J. on Signal & Image Processing, Vol. 01, No. 03, Dec 2010

Conditional Averaging
a New Algorithm for Digital Filter
Sukesh Rao M, NMAMIT,
E&C Dept, Nitte, India.
Email: sukesh_muligar@yahoo.co.in
Dr. S. Narayana Iyer, NMAMIT, Nitte, India.
Email: iyer_narayana@yahoo.com

Abstract—This paper aims at designing a new algorithm for 1) For a fixed sampling frequency, the sample of the
digital filters. The traditional methods like FIR, IIR have been incoming signal is processed for three different levels of
improved in recent times with new approaches. However, the conditionality, resulting in three different types of cutoff
developments have used complex arithmetic calculation and frequencies or the signal bandwidth.
dedicated DSP processors. In this research project, effort has
been made to reduce such complexities using a procedure
2) A relation is formed between the conditional statements
based on the technique of Conditional Averaging. The entire and the cutoff frequencies which remain true for any
algorithm is developed using more of conditional statements number of remaining conditional statements and the
and less of arithmetic calculations. desired cutoff frequencies.
Digital signals are filtered at different stages of 3) A mixed harmonic signal is fed to the system to obtain
signal processing. However high speed processor is used for the system response for different cutoff frequencies.
different calculations associated with filtration process. An
averaging is one such scheme used in simple FIR filter, which II. CONDITIONAL AVERAGING- THE PROPOSED
performs low pass filtering operation. Conditional Averaging
TECHNIQUE
is a new technique, which is one of the improvements in
continuous time averaging. Conditional Averaging algorithm Conditional averaging is a new scheme proposed in the
is explained in this practice with different examples for the area of different averaging techniques [1]. Simple
design of low pass filter. This algorithm has been successfully averaging with N points will reduce any of the AC
tested using digital starter kit with TMS3206416v DSP
components corresponding to the amplitude variations. All
processor. Using code composer studio, the entire algorithm is
written in C/C++ language and compiled into an assembly averaging techniques act as low pass filter with the filter
language. Conditional averaging can be implemented with any coefficients equal to 1/N. conditional averaging will not
general purpose processor to arrive at other types of filters use any such kind of filter coefficients and any definite
with certain necessary modifications. mathematical relation as such.
The Fast Fourier Transform (FFT) is the method used in
Index Terms— FFT, DSP, LPF
the DSP (digital signal processing) to find out the
frequency spectrum of any given signal. It is a
I. INTRODUCTION
mathematical operation for obtaining the accurate
Filter is a system which selectively changes the wave frequency spectrum. It is also possible to predict the
shape, amplitude, frequency content and phase frequency spectrum of the signal with signal amplitude
characteristic of a signal as desired. In digital signal variations. The spectrum so obtained may not be accurate
processing, based on the design constraints digital filters of and it is approximated. If we know the sampling frequency
FIR, IIR or even other types are commonly in usage. In real or the timing interval of the incoming signal, it is possible
time signal processing, these filters use dedicated to predict the harmonics present in the signal. Figure 1
Microprocessor system to carry out complex floating point shows a random signal. We can determine the frequency
arithmetic operation. To acquire high accuracy and high plot accurately for the signal shown in figure 1 using the
precision of the system response, high frequency frequency transform techniques. Also possible to predict
supportive DSP processor is used. The scope of this work approximately the harmonics present in the signal by
namely Conditional Averaging is to minimize the complex knowing the sampling frequency. Let us assume that the
arithmetic operation and obtain better response for the signal is sampled at a rate of fs Hz and figure 2 (a) shows
required design using general purpose microprocessor. the resulting discrete samples.
From the sampled signal, one can conclude that, (1/ fs)
A. Problem Definition
is the time gap between two samples. If the signal varies
A specially devised technique of conditional averaging with more number of successive samples, then it
has been developed to design a low pass filter. The term corresponds to lower harmonics
‘conditional averaging’ has been assigned to this method as Fluctuation with lesser number of successive samples
it performs the averaging of a given data set based on corresponds to higher harmonics. All such samples
certain attributed conditions. This algorithm has been tested which contribute to the frequency component less than fs
for different cutoff frequencies maintaining the sampling can be easily predicted. These samples are marked and
frequency at a fixed rate. MATAB simulation technique shown in figure 2(a). The samples marked in red, blue and
has been used to confirm and validate the algorithm. The yellow color; corresponds to different frequency
algorithm is verified with the following criteria. components within the bandwidth fs. The higher harmonic

© 2010 ACEEE 28
DOI: 01.IJSIP.01.03.188


is marked in red color and it contains approximately 7 samples considered for the averaging. Apart from this type
samples. This corresponds to a frequency component of averaging one more kind can be introduced, which
(1/7)fs. The next harmonic is marked in blue color. It performs the sample modification similar to the averaging.
Consider red colored samples from the figure 2 (b) for the
sample modification. To remove the fluctuation of this
signal, a linear path is predicted between first and the last
sample. The linear path is formed between time index t=1
and t=8. It is shown in figure 2 (b). If there are even
number of samples, then a value is obtained at the center
[t=4.5] of first and last sample. From this value at t=4.5, the
averaging with first and last sample leads to two more new
sample sets corresponding to t=3 and t=6. Same method of
averaging is performed to obtain the values at t= 2, 4, 5 and
Figure 1. An arbitrary Signal
consists of approximately 15 samples, which contributes to 7.
(1/15)fs frequency spectrum of the signal. Similarly the The newly obtained values will make the signal shown
yellow colored sample set belongs to lowest harmonic of in figure 2 (c). Same kind of averaging is performed to the
the signal and this frequency is less than (1/40)fs. yellow colored samples. Since we perform the averaging
To suppress the two harmonics with samples red and only for a set of samples with certain conditions on
blue colors and maintain only the harmonic lower than amplitude variations, this algorithm is named as
“conditional averaging”. It indicates that this proposed
algorithm results in reduced computations, which is
certainly an overwhelming advantage.
Signal averaging is performed on the basis of the
variation in the magnitude of the incoming samples, the
averaging takes place always between two samples.
Averaging of two samples is performed over N points to
determine the new possible sample of the signal. Not all the
(a) Samples set identified with different color incoming signal sample undergo for the averaging
(b) operation.
To test this algorithm, consider a signal, which is
sampled at a rate of fs with four different frequency
components f1, f2, f3 and f4 with different phase angle Φ1,
Φ2, Φ3 and Φ4.We express this signal as follows.

(b) Magnified view of samples with red color
By assuming suitable values of these frequencies and
phase angles, the simulation of the conditional averaging is
carried out. Consider f1, f2, f3 and f4 to be 600 Hz, 50 Hz ,
2000 Hz and 800 Hz respectively with phase angle of 2Π/3,
0, Π/5 and Π/2.

(c) Final reconstructed Signal
Figure 2

(1/40)fs, we can think of a technique which will process
only these samples. Continuous averaging will suppress the
higher frequency components depending on the number of

© 2010 ACEEE 29
DOI: 01.IJSIP.01.03.188


bandwidth at
i.e.
After performing the conditional averaging, the resulting
sample is shown in figure 4 (b) with its FFT.
The frequency 1250 Hz corresponds to the m=25 and
all the values with m>25 are attenuated. Hence it is

Figure 3 Resulting wave for 100 samples after sampling

Conditional averaging is performed for the first 100
samples of the sampled input signals as shown in figure 4
(a) to get different cutoff frequency for a LPF. The
conditional averaging is carried out for three different cases
a) Four sample-conditional Averaging
b) Eight sample- conditional Averaging (a) Input FFT
c) Sixteen sample- conditional Averaging
A. Four sample-conditional Averaging
Four sample-conditional averaging uses only four sample
buffers. The samples in the buffer are used for the
comparison process to check the conditions of a relational
set. A relational set is an array, which is obtained by
comparing two samples each from the main sample set and
contains combination of only two values. If the signal
frequency of interest is f, then the sampling should be
carried out at the rate more than 4f. It is also possible that if
a signal is sampled at fs, then the signal can be band
limited to minimum of fs/4. Conditional averaging with
four sample is the minimum possible selection of the cutoff
(b) Output FFT
frequency for the design of LPF.
The Algorithm uses following steps functioning like a LPF for the designed frequency fs/4. The
1) Take new signal sample to the buffer of size four in first- process introduces a delay of 4 sample time between an
in last-out order. input and the output value at any instant of time. The
2) Check the relation between all 4 samples by getting a algorithm mentioned for the conditional averaging is
new set of relational array with 3 elements. implemented in the C language.
3) In the relational array search for the unwanted sequence
and eliminate that sequence in the buffer by performing B. Eight sample-conditional Averaging
Averaging of four samples. Four sample-conditional averaging is simpler and the
4) From the updated buffer, the last sample is taken as basic averaging. Whereas eight sample-conditional
output and entire process is repeated from step 1. averaging includes the signal constraints of 4 sample
In the figure 3 or figure 4 (a), samples are taken at conditional averaging also. An 8 sample buffer is
5000Hz sampling rate and a 100 point FFT is obtained for maintained for the comparison process to check for the
the frequency analysis. Here m varies from 0 to 99 and conditions. Eight sample conditional averaging gives a
m=100 correspond to the Nyquist rate, i.e. 5000 Hz in this signal bandwidth of fs/8. Conditional averaging with eight
case. sample uses the algorithm used similar to that of four
To find the frequency of analysis ‘f’ from the sample-conditional averaging to get the bandwidth for the
above FFT desired of LPF.
To find the frequency of analysis ‘f’ from the FFT
shown in figure 5.

Where N=100 an fs =5000 Hz
The four samples conditional averaging will result in a

© 2010 ACEEE 30
DOI: 01.IJSIP.01.03.188


Where N=100 an fs =5000 Hz
The eight sample-Conditional Averaging will give cutoff
value at fs/8. i.e. 5000/8=625 Hz .This can be verified by
figure5.

The frequency 625 Hz corresponds to m=12.5 and all the
values m>12.5 are attenuated. Hence it is acting like a LPF
for the desired bandwidth. The whole process introduces a
delay of 8 sample time between an input and the output.

Figure 6 outputs FFT of 16 sample conditional averaging

III. RESULT
Conditional averaging algorithm is verified in real time
to compare the result of the theoretical simulation. To
perform this operation DSP Starter kit (DSK6416) is used
Figure 5. Output FFT of 8 sample conditional averaging for the programming and the debugging. TMS320C6416v
is the key element in DSK6416 system and it has got all the
other speech processing peripherals interfaced to it. Input
C. Sixteen sample -conditional Averaging signal are fed using audio codec and then processed by the
In this Averaging technique only sixteen sample buffers DSP processor.
are maintained for the comparison process to check the Audio codec performs analog to digital conversion and
conditions. Sixteen sample-conditional averaging includes vice versa. Analog signals are mixed using simple passive
the both the processing stages of four and eight sample components to get the mixture of all the input signals.
averaging. For a sampling frequency fs, the sixteen sample Signal selections are made such that, they will be within
conditional averaging given a bandwidth limit of fs /16 in the sampling frequency of the system. The sampling
the design of LPF. To find the frequency of analysis ‘f’ frequency of the DSK6416 is selected by the program
from the above FFT shown in figure 6. command to set at 8 KHz. All input signals are band
limited to less than 4 KHz to satisfy the Nyquist rate.
A real time testing has been carried out for sixteen sample
conditional averaging. Sixteen sample-conditional
where N=100 an fs =5000 Hz. The eight sample-
averaging gives a very small bandwidth of fs /16. More
conditional Averaging will give cutoff value at fs /8. i.e.
conditional statements has to be included in the processing
5000/16=312.5 Hz .This can be verified by figure 6.
of the signal, given that the number of samples considered
The frequency 312.5 Hz corresponds to m=6.25 and all
are more for the signal processing. The time domain input
the values m>6.25 are attenuated. Hence it is behaving like
and the output signal after the processing through
a LPF. The whole process introduces a delay of 16 sample
conditional averaging are shown in the figure 7 (a).
time between an input and the output.
A test is conducted with different input FFT, wherein a
FIR filtering obeys sinusoidal functional manipulation,
signal of higher frequency component within the input
hence the output samples are also the part of sine or cosine
band limit is fed into the system. The output FFT obtained
functions. The above work is still modified for the better
clearly shows the attenuation of the signal above 500Hz in
performance for different frequencies. When more samples
the spectrum. The signals above 4 KHz are also attenuated,
are taken for a particular conditionality, it is possible to
as the signal was sampled at 8 KHz rate and hence it can
modify the range of the bandwidth. Conditional Averaging
not reconstruct the signal beyond 4 KHz (refer figure 7
makes use of the deterministic signals like ECG, EMG and
(c)). Including more conditional statements for a signal of
EEG, which are the better sources of signals for the
higher frequency value, the output response of the system
analysis. To reiterate, this algorithm reduces the
we find is much better.
computation.

© 2010 ACEEE 31
DOI: 01.IJSIP.01.03.188


processing, but the conditional averaging uses only limited
number of samples, which satisfy the conditional array set.
This results in reduced computational time and burden on
the processor.
Any type of general purpose processor can be used to
design the system for the signal processing using this
algorithm. Thus, unlike other algorithm, this method
requires only a general purpose processor. However, in the
(a) Input and Output signal
proposed algorithm, in order to verify all the sets of
possible combination within the short period of time,
before the next sample arrives, a high speed general
purpose processor is required. This processor should be
able to execute minimum of 100 to 1000 instructions
within one sampling time. For the lower bandwidth, system
undergoes more conditional statements and therefore it
requires more instruction for the processing.
Conditional algorithm can also be developed for the
analysis of ECG, EEG signals as well. Therefore,
conditional averaging becomes a very useful filtering
algorithm to analyze the biomedical signals. All such
biomedical signals are of low frequency and any high
frequency noise or the signal surge can be easily detected
(b)Input signal FFT using the conditional averaging.
The main drawback of the system is that, it may distort
the signal by adding many other lower harmonics within
the bandwidth. To alleviate this and get a desired
bandwidth, it is necessary to include more conditional
statements during processing.
This conditional averaging is possible to be applied to high
pass filtering operation also. It may not be just averaging as
performed in the case of the low pass filter design. Design
of narrow band pass filter using the conditional averaging
algorithm is another future work.

REFERENCES
(c) Out put FFT [1] Welch P. D “ The use of Fast Fourier Transform for the
estimation of power spectra: A method based on time
Fig 14 averaging over short, Modified periodgrams” IEEE
transaction on audio and electroacoust., Vol. AU-15 No.2
CONCLUSION June 1967
[2] Richard G Lyons, Understanding Digital signal processing
The desired bandwidth for the proposed low pass filter Pearson Education third edition.2001.
could be achieved after the simulation and debugging of [3] TMS320C6713 DSK Technical Reference, SPECTRUM
the algorithm using the conditional averaging, which works DIGITAL, INC
as a low pass filter. It may be noted that filter uses simple [4] TMS320 DSP datasheet by Texas instrumentation.
two values averaging at a time and gives the corrected [5] Emmanuel C. Ifeachor, Digital Signal Processing, Pearson
output by consuming less processing time. Normally time Education
domain averaging uses all the incoming samples for the

© 2010 ACEEE 32
DOI: 01.IJSIP.01.03.188

Conditional Averaging a New Algorithm for Digital Filter

More Related Content

What's hot (20)

Viewers also liked (11)

Similar to Conditional Averaging a New Algorithm for Digital Filter (20)

More from IDES Editor (20)

Recently uploaded (20)

Conditional Averaging a New Algorithm for Digital Filter