Configure vtp

PT Activity 4.3.3: Configure VTP

Topology Diagram

Learning Objectives
• Investigate the current configuration
• Configure S1 as VTP server
• Configure S2 and S3 as VTP clients
• Configure VLANs on S1
• Configure trunks on S1, S2, and S3
• Verify VTP status on S1, S2, and S3
• Assign VLANs to ports on S2 and S3
• Verify VLAN implementation and test connectivity

Introduction
In this activity, you will practice configuring VTP. When Packet Tracer first opens, the switches already
contain a partial configuration. The user EXEC password is cisco and the privileged EXEC password is
class.

Task 1: Investigate the Current Configuration

Step 1. Verify the current running configuration on the switches.
What configurations are already present on the switches?
____________________________________________________________________________________

All contents are Copyright © 1992–2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 6

CCNA Exploration
LAN Switching and Wireless: VTP PT Activity 4.3.3: Configure VTP

____________________________________________________________________________________

____________________________________________________________________________________

Step 2. Display the current VLANs on each switch.
Are there any VLANs present? Are the VLANs user created VLANs or default VLANs?
____________________________________________________________________________________

S1#show vlan brief
VLAN Name Status Ports
---- ------------------------ --------- -----------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
Gig1/1, Gig1/2
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active

Completion should be at 0% at the end of this Task.

Task 2: Configure S1 as VTP Server

Step 1. Configure the VTP mode command.
S1 will be the server for VTP. Set S1 to server mode.
S1(config)#vtp mode server
Device mode already VTP SERVER.
S1(config)#
Notice that the switch is already set to server mode by default. However, it is important that you explicitly
configure this command to insure the switch is in server mode.

Step 2. Configure the VTP domain name.
Configure S1 with CCNA as the VTP domain name. Remember that VTP domain names are case
sensitive.
S1(config)#vtp domain CCNA
Changing VTP domain name from NULL to CCNA
S1(config)#

Step 3. Configure the VTP domain password.
Configure S1 with cisco as the VTP domain password. Remember that VTP domain passwords are case
sensitive.
S1(config)#vtp password cisco
Setting device VLAN database password to cisco
S1(config)#


CCNA Exploration

Step 4. Confirm configuration changes.
Use the show vtp status command on S1 to confirm that the VTP mode and domain are configured
correctly.
S1#show vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 64
Number of existing VLANs : 5
VTP Operating Mode : Server
VTP Domain Name : CCNA
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x8C 0x29 0x40 0xDD 0x7F 0x7A 0x63
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00

To verify the VTP password, use the show vtp password command.
S1#show vtp password
VTP Password: cisco
S1#

Step 5. Check results.
Your completion percentage should be 8%. If not, click Check Results to see which required
components are not yet completed.

Task 3: Configure S2 and S3 as VTP Clients

Step 1. Configure the VTP mode command.
S2 and S3 will be VTP clients. Set these two switches to client mode.

Step 2. Configure the VTP domain name.
Before S2 and S3 will accept VTP advertisements from S1, they must belong to the same VTP domain.
Configure S2 and S3 with CCNA as the VTP domain name. Remember that VTP domain names are case
sensitive.

Step 3. Configure the VTP domain password.
S2 and S3 must also use the same password before they can accept VTP advertisements from the VTP
server. Configure S2 and S3 with cisco as the VTP domain password. Remember that VTP domain
passwords are case sensitive.

Step 4. Confirm configuration changes.
Use the show vtp status command on each switch to confirm that the VTP mode and domain are
configured correctly. Output for S3 is shown here.

S3#show vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 64
Number of existing VLANs : 5
VTP Operating Mode : Client


CCNA Exploration

VTP Domain Name : CCNA
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x8C 0x29 0x40 0xDD 0x7F 0x7A 0x63
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00

Notice that the configuration revision number is 0 on all three switches. Why?
____________________________________________________________________________________

____________________________________________________________________________________

____________________________________________________________________________________

To verify the VTP password, use the show vtp password command.
S3#show vtp password
VTP Password: cisco
S3#


Task 4: Configure VLANs on S1
VLANs can be created on the VTP server and distributed to other switches in the VTP domain. In this
task you will create 4 new VLANs on the VTP server, S1. These VLANs will be distributed to S2 and S3
via VTP.

Step 1. Create the VLANs.
For grading purposes in Packet Tracer, the VLAN names are case-sensitive.
• VLAN 10 named Faculty/Staff
• VLAN 20 named Students
• VLAN 30 named Guest(Default)
• VLAN 99 named Management&Native

Step 2. Verify VLANs.
Use the show vlan brief command to verify the VLANs and their names.
S1#show vlan brief

VLAN Name Status Ports
---- ------------------------- --------- ------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
Gig1/1, Gig1/2
10 Faculty/Staff active
20 Students active
30 Guest(Default) active

CCNA Exploration

99 Management&Native active
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active

If you enter the same command on S2 and S3, you will notice that the VLANs are not in their VLAN
database? Why not?
____________________________________________________________________________________

____________________________________________________________________________________


Task 5: Configure Trunks on S1, S2, and S3
Use the switchport mode trunk command to set trunk mode for each of the trunk links. Use the
switchport trunk native vlan 99 command to set VLAN 99 as the native VLAN.

Step 1. Configure FastEthernet 0/1 and FastEthernet 0/3 on S1 for trunking.
Enter the appropriate commands to configure trunking and set VLAN 99 as the native VLAN.
Once configured, Dynamic Trunking Protocol (DTP) will bring up the trunk links. You can verify S2 and S3
are now trunking by entering the show interface fa0/1 switchport command on S2 and the show
interface fa0/3 switchport command on S3.
If you wait a few minutes for Packet Tracer to simulate all the processes, S1 will advertise the VLAN
configuration to S2 and S3. This can be verified on S2 or S3 with both the show vlan brief command and
the show vtp status command.
However, it is a best practice to configure both sides of the trunk links to the on mode.

Step 2. Configure Fast Ethernet 0/1 on S2 for trunking.

Step 3. Configure Fast Ethernet 0/3 on S3 for trunking.


Task 6: Verify VTP Status
Using the show vtp status and show vlan brief commands, verify the following.
• S1 should show server status
• S2 and S3 should show client status
• S2 and S3 should have VLANs from S1
Note: VTP advertisements are flooded throughout the management domain every five minutes or
whenever a change occurs in VLAN configurations. To accelerate this process, you can switch between

CCNA Exploration

Realtime mode and Simulation mode until the next round of updates. However, you may have to do this
multiple times since this will only forward Packet Tracer’s clock by 10 seconds each time. Alternatively,
you can change one of the client switches to transparent mode and then back to client mode.
What is the configuration revision number? ___________
Why is the configuration revision number higher than the number of VLANs you created?
____________________________________________________________________________________

____________________________________________________________________________________

What is the current number of existing VLANs? ___________
Why are there more existing VLANs than the four you created?
____________________________________________________________________________________

Completion should still be at 77% at the end of this Task.

Task 7: Assign VLANs to Ports
Use the switchport mode access command to set access mode for the access links. Use the
switchport access vlan vlan-id command to assign a VLAN to an access port.

Step 1. Assign VLANs to ports on S2.
• Fa0/11 on VLAN 10

Step 2. Assign VLANs to ports on S3.


Task 8: Verify VLAN Implementation and Test Connectivity

Step 1. Verify VLAN configuration and port assignments.
Use the show vlan brief command to verify VLAN configuration and port assignments on each switch.
Compare your output to the topology.

Step 2. Test connectivity between PCs.
Pings between PCs on the same VLAN should succeed, while pings between PCs on different VLANs
should fail.
From PC1 ping PC4.
From PC2 ping PC5.
From PC3 ping PC6.

Configure vtp

More Related Content

What's hot (20)

Viewers also liked (9)

Similar to Configure vtp (20)

Configure vtp