Configuring junos basics

Junos®
Fundamentals Series
By Ian Jarrett and Sean Clarke
It’s day one and you have a job to
do. Start configuring Junos today.
In this Day One booklet you’re just
a few hours away from setup of
the base system settings of your
router, switch, or security device.
DAY ONE:
CONFIGURING JUNOS BASICS

Junos®
Fundamentals Series
Juniper Networks Day One booklets provide just the information you need on day one. They are
written by subject matter experts and engineers who specialize in getting networks up and running.
Look for other titles covering high-performance networking solutions at www.juniper.net/dayone.
This book is available in both PDF and printed formats.
Day One: Configuring Junos Basics
This second booklet in the Junos Fundamentals Series helps you to configure the basic settings
of your device and to learn more about configuration mode. These settings are the first steps to
configuring a Junos device, whether you are setting up a router, switch, or security platform.
Building upon the foundation set by the first booklet, Day One: Configuring Junos Basics continues
the practical tutorial for first-time users of Junos and Juniper products. It is also written as a
reference or refresher for more experienced Junos administrators.
“The Day One series is extremely useful in my day-to-day activities with
Juniper devices. It answers my questions about how the Junos configuration
process works and how to set up devices in my network, providing lots of
practical tips and examples from Juniper experts. This is exactly what I was
looking for.”
Gadde Pradeep, JNCIA-M, JNCIS-M, JNCIA-EX, JNCIA-ER, JNCIS-ER
Day One: Configuring Junos Basics shows you how to:
• Create a handy checklist of settings to use in configuring the system basics
• Configure base system settings
• Create login accounts and permissions
• Set up SNMP to work with your existing systems
• Monitor your device remotely and configure system logs
• Installs Web-based management
• Make changes faster with configuration shortcuts
• Streamline device setup with configuration groups and templates
• Compare your resulting configuration to the booklet example
#2
7100105

JUNOS®
Software Fundamentals Series
Day One: Configuring JUNOS Basics
By Ian Jarrett and Sean Clarke
Chapter 1:Creating a Checklist. . . . . . . . . . . . . . . . . . . . . .5
Chapter 2:Configuring the System Basics . . . . . . . . . . . .11
Chapter 3:Setting Up Users . . . . . . . . . . . . . . . . . . . . . . .25
Chapter 4:Configuring SNMP . . . . . . . . . . . . . . . . . . . . .33
Chapter 5:Using Monitoring and Logging . . . . . . . . . . . . .43
Chapter 6: Working with ConfigurationTemplates
and Other Shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
And a PDF supplement to the print edition (available at www.juniper.net/dayone)
Appendices:Day OneWorksheet,Configurations,
and More . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

© 2009 by Juniper Networks, Inc. All rights
reserved. Juniper Networks, the Juniper Networks
logo, JUNOS, NetScreen, and ScreenOS are
registered trademarks of Juniper Networks, Inc. in
the United States and other countries. JUNOSe is a
trademark of Juniper Networks, Inc. All other
trademarks, service marks, registered trademarks,
or registered service marks are the property of
their respective owners.
Juniper Networks assumes no responsibility for
any inaccuracies in this document. Juniper
Networks reserves the right to change, modify,
transfer, or otherwise revise this publication
without notice. Products made or sold by Juniper
Networks or components thereof might be covered
by one or more of the following patents that are
owned by or licensed to Juniper Networks: U.S.
Patent Nos. 5,473,599, 5,905,725, 5,909,440,
6,192,051, 6,333,650, 6,359,479, 6,406,312,
6,429,706, 6,459,579, 6,493,347, 6,538,518,
6,538,899, 6,552,918, 6,567,902, 6,578,186, and
6,590,785.
Day One Series Editor: Cathy Gadecki
Writers: Ian Jarrett, Sean Clarke
Editing: Nancy Koerbel
Literary Management: Ames & Eames, Inc.
Printed in the USA by Vervante Corporation.
Version History: v1 August 2009
2 3 4 5 6 7 8 9 10
About the Authors
Ian Jarrett is a Senior Product Line Manager at
Juniper Networks, responsible for JUNOS
Software. He has over eleven years of experience
with JUNOS and is happy to share some of that
experience with a wider audience.
Sean Clarke is a Senior Systems Engineer at
Juniper Networks, with over nine years of hands-
on experience with JUNOS.
Authors’ Acknowledgments
The authors want to thank the many people who
assisted us in creating this book. Our literary
manager Patrick Ames guided us and Nancy
Koerbel edited our writing. The Day One Series
Editor Cathy Gadecki saved this project several
times and tirelessly devoted many days to working
with us. Michael Scruggs and Marilyn Kerr ﬁne-
tuned our attempts at instructional clarity. David
Nguyen, Jerish Parapurath, Jennifer Pulsifer, and
Brad Woodberg answered our questions and
provided technical review of sections. Ian Jarrett
would personally like to thank everybody on the
Juniper Networks team who has helped to make
this publication possible; and Sean Clarke would
like to give thanks to the production team who
turned technical jargon into English, and also to
Marian for her patience and support.
A free PDF version of this booklet is available at:
www.juniper.net/dayone.
ii

Welcome to Day One
Day One booklets help you to quickly get started in a new topic with
just the information that you need on day one. The Day One series
covers the essentials with straightforward explanations, step-by-step
instructions, and practical examples that are easy to follow, while also
providing lots of references on where to learn more.
Why Day One Booklets?
It’s a simple premise – you want to use your Juniper equipment as
quickly and effectively as possible. You don’t have the time to read
through a lot of different documents. You may not even know where
to start. All you want to know is what to do on the first day, day one.
Day One booklets let you learn from Juniper experts, so you not only
find out how to run your device, but also where the shortcuts are, how
to stay out of trouble, and what are best practices.
WhatThis Booklet OffersYou
Day One: Configuring JUNOS Basics helps you to configure the basic
settings of your device and to learn more about configuration mode.
These settings are the first steps to configuring a JUNOS device,
whether you are setting up a router, a switch, or a security platform.
When you’re done with this booklet, you’ll be able to:
P Create a handy checklist of settings to use in configuring the
system basics
P Configure basic system settings
P Create login accounts and permissions
P Set up SNMP to work with your existing systems
P Monitor your device remotely and configure system logs
P Install Web-based management
P Make changes faster with configuration shortcuts
P Streamline device setup with configuration groups and templates
P Compare your resulting configuration to the booklet example
iii

TryingThings Out inYour Own Device
Having access to a JUNOS device while reading is useful for working
along with the steps and commands of the examples. The Appendix
available in the electronic version of this booklet provides a reference
configuration. If you follow along in your own device by entering all of
the configuration commands designated by an arrow ► in the left
margin (and no other commands), your resulting configuration should
match the expected configuration in the Appendix. For example:
► root@juniper1# set class super-user
To access JUNOS Software, you must first have access to the device
itself, either through the console port or the management port.
Because each network is different, the process of logging in to de-
ployed equipment is beyond the scope of this booklet. So before
attempting to log in to the JUNOS command-line interface, you need
to know how to access your device on the network, or have physical
access to it.
MORE? If you need information on deploying your device, see the Quick Start
guide for your product at www.juniper.net/techpubs/.
What to Enter intoYour Device
With a focus on doing, Day One booklets include lots of examples.
The examples show screen output in a fixed-width font with the
commands that you enter in boldface. If the command includes user
named input (such as the name of a file, group, or policy), the exam-
ples show it as boldface italic. The booklet uses these conventions in
both the examples and their discussion to identify types of input in the
booklet. However, when you type commands into the command-line
interface (CLI), all input is plain-text entry.
WhatYou Need to Know Before Reading
Before reading this booklet, you should be familiar with basic net-
working concepts and the topics covered in the first booklet of the
JUNOS Software Fundamentals series. Day One: Exploring the
JUNOS CLI introduced the basic commands used to configure and
operate the JUNOS device, summarized in the table in the Appendix
(available in the electronic version).
iv

Chapter 1
Creating a Checklist
Hostname . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Loopback Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Management Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Backup Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Domain Name System (DNS). . . . . . . . . . . . . . . . . . . . . . .7
Time Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
User Names and Passwords . . . . . . . . . . . . . . . . . . . . . . . 8
RemoteAuthentication Servers. . . . . . . . . . . . . . . . . . . . . 9
Network Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Network Management System . . . . . . . . . . . . . . . . . . . . 10
That’s the End of the Gathering . . . . . . . . . . . . . . . . . . . .10

6 Day One:Configuring JUNOS Basics
JUNOS Software is a network operating system that runs many of the
Juniper Network platforms. Whether it is your first day setting up a
new router, a switch, or a security platform, this booklet walks you
through the steps to configure the JUNOS basics. These steps are
straightforward and follow common practices well-known to experi-
enced network administrators.
As with any network device, regardless of the manufacturer, there are
a number of fundamental settings to configure before you can declare
it “ready for use.” For example, the device needs to know its assigned
IP addresses, which users are allowed to enter, as well as its manage-
ment basics.
This first chapter steps you through the list of information you may
need to configure the device basics. Record this information in the
margins or in a worksheet provided in the Appendix, so you have a
record of vital information and because sometimes a pen and paper is
easier to use when you’re moving among the racks. If you gather all
the details described in the sections of this chapter, you can breeze
through the basic device setup discussed in Chapters 2 through 5.
Hostname
Most devices in your network infrastructure – whether they are
routers, switches, servers, or firewalls – are known by a specific name
rather than by the device’s IP address. A name is simply easier to
remember than a long string of numbers. The device name is also
known as the hostname.
Often, administrators choose a hostname that reflects the device’s use
in the network, for example: uk-london-R1. The hostname should be
unique to the device. It is usually added to the DNS servers so that
administrators can connect to the device using the easy-to-remember
hostname.
Loopback Interface
Most of the addresses you configure on your device are physical
interfaces, however, the loopback interface is a virtual interface – an
interface not associated with any hardware or network. While physical
interfaces might be removed or their addresses changed, the loopback
address never changes. The loopback address has many different uses
in the operation and management of the network.

Chapter 1:Creating a Checklist 7
Management Interface
A management interface lets authorized users and management
systems connect to the device over the network. If your device is an
EX Series Ethernet Switch or an M Series or MX Series router, it has
a dedicated management port on the front panel. For other types of
platforms you can configure a management interface on one of the
network interfaces; this interface can be dedicated to management
or shared with other traffic.
Before users can access the management interface, you must configure
it. Information required to set up the management interface includes
its IP address and prefix. In many types of JUNOS devices (or recom-
mended configurations) it is not possible to route traffic between the
management interface and the other ports. Therefore, you should
select an IP address in a separate (logical) network, with a separate
prefix (netmask).
Backup Router
If JUNOS is running on a network device that performs Layer 3
forwarding (such as a router) you may want to specify a backup
router. A backup router can be used during the initial boot process of
JUNOS, before any routing protocols have converged. It allows the
device to establish a Layer 3 connection quickly, thus keeping unavail-
ability to a minimum. In selecting a backup router, it is common
practice to choose the default gateway of your management network
that is directly connected to your device.
Domain Name System (DNS)
It is easier for most people to remember names rather than numbers
especially if those numbers are IPv4 addresses. Because of this, domain
name system (DNS) servers are used to map device hostnames to IP
addresses and vice versa.
DNS allows you to use names to designate key external systems such
as file and log servers that your device may need to contact. The DNS
server maintains a centralized repository for device hostnames on the
network, ensuring each device hostname is unique. This centralized
repository makes it easier to query and to administer translations
between the network IP addresses and hostnames. You can configure
your device to query one or more DNS servers via their IP addresses.

Time Servers
The IETF defined the Network Time Protocol (NTP) to synchronize the
clocks of computer systems connected to each other over a network.
Most large networks have an NTP server that ensures that time on all
devices is synchronized, regardless of the device location. If you use
NTP server(s) on your network, ensure you know the address(es).
User Names and Passwords
The root account of JUNOS Software provides full administrative
access to your device with complete control over its configuration and
operation. The root account is often referred to as the superuser.
In new devices, the root account has no password. You must add a
password to the root account before you can commit any configuration.
The stronger you make the password, the harder it is for others to
discover it and use it to break into the account.
JUNOS helps to enforce the use of strong passwords. For example,
valid passwords must:
n Be a minimum length of 6 characters
n Contain at least one change of case or character class
n Be at least six characters long and use at least three of the five
defined character classes (uppercase letters, lowercase letters,
numbers, punctuation marks, and other special characters).
Control characters are not recommended for passwords.
BEST PRACTICE Increase the length of the password and the minimum number of case,
digit, and punctuation changes to set up safer passwords. An example
of a good password would be: t3aMX*u7rS.
In addition to the root user, it is highly recommended that you create at
least one other local user. This user can log in when you need to per-
form administration or maintenance tasks on the device.
In assigning usernames, do not include spaces, control characters,
colons, or commas. A username can be a maximum length of up to 64
characters. User passwords also require a change of case, digits, or
punctuation.
8 Day One:Exploring the JUNOS CLI
You should keep all your
passwords secret at all times.If
you write down a password
here,make sure that this
document is kept safe and
secure.

Chapter 1:Creating a Checklist 9
RemoteAuthentication Servers
You probably already use a remote authentication server (or servers)
in your network. It’s a recommended best practice, because the
server(s) allow you to centrally create a consistent set of user accounts
for all devices in your network.
Using a central server has multiple advantages over the alternative of
creating local users on each and every device – a time-consuming and
error-prone task. A central authentication system also simplifies the
use of one-time password systems such as SecureID, which offer
protection against password sniffing and password replay attacks, in
which someone uses a captured password to pose as a system adminis-
trator.
There are two basic methods of remote authentication in use by most
enterprises today: RADIUS (Remote Authentication Dial In User
Service) and TACACS+ (extended Terminal Access Control Access
Control System). JUNOS can be configured to query multiple remote
authentication servers of both types.
MORE? If you want more information about RADIUS or TACACS+ technolo-
gies, see the System Basics Configuration Guide of the JUNOS techni-
cal documentation. All Juniper technical documentation is available at
www.juniper.net/techpubs.
Network Interfaces
If your device is performing Layer 3 forwarding (e.g. IP routing), it
needs at least one IP address assigned to an interface. If you have more
than one network interface, you need at least one IP address for each.
This booklet helps you to configure a Gigabit Ethernet interface so
that you can get your device “up and running” on your network.
MORE? Day One: Configuring JUNOS Interfaces and Routing discusses how
to configure other types of interfaces. Check availability and down-
load your copy at www.juniper.net/dayone.

Network Management System
Do you use a central network management system (NMS)? Most
NMS’s use a version of Simple Network Management Protocol
(SNMP) that can monitor the status of JUNOS devices that send
unsolicited messages called traps. You can configure the IP address of
your NMS so that JUNOS knows where to send its traps.
SNMP uses a very basic form of authentication called community
strings to control access between a manager and remote agents, and
vice versa. Community strings are administrative names used to group
collections of devices (and the agents running on them) into common
management domains. If a manager and an agent share the same
community, they can talk to one another.
Many people associate SNMP community strings with passwords and
keys because the jobs they do are similar. As a result, SNMP communi-
ties are traditionally referred to as strings. The community string is the
first level of management authentication implemented by the SNMP
agent in JUNOS.
You may also want to configure remote logging on your device.
JUNOS uses a syslog mechanism similar to many Unix devices to
forward log messages to a specified log host address. This allows each
of your devices to forward their messages to one central host, making
it easier to monitor the network as a whole. Syslog is a very flexible
and rich way of logging messages and is used by many device vendors
to supplement the information provided by SNMP traps.
That’s the End of the Gathering
That’s it. That’s the information you need to begin your day one
configuring. Print out the Configuration Information Worksheet from
the Appendix (included in the electronic version of this booklet) and
record the information you’ve gathered. Or just write the details for
your devices in the margins of a printed copy of this booklet. Now,
you have a reference to complete the commands and steps described in
the remaining chapters of this booklet.

Chapter 2
Conﬁguring the System Basics
Conﬁguring Base System Settings . . . . . . . . . . . . . . . . . .12
Reaching a Domain Name System Server . . . . . . . . . . . .18
Setting Up the Date andTime. . . . . . . . . . . . . . . . . . . . . 19
Introducing Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . .21
ReviewingYourWork . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

In the previous chapter you gathered the essential configuration
information to use with this booklet. In this chapter, you begin the
actual setup of your device with the basic settings, including the base
system, user accounts, remote access, and interfaces.
Follow along in your own device by entering all the configuration
commands designated by an arrow ► in the left margin. You can then
compare your resulting configuration with the expected configuration
included in the Appendix.
A pratical change is to customize your command entries using the
specific information gathered in Chapter 1. When you compare your
resulting configuration with the expected configuration in the Appen-
dix, the only differences will be in the customizable fields, and your
device will be ready with the basic settings to run in your network.
Configuring Base System Settings
This section guides you through the first steps in configuring your
device, including base system settings of root (administrator) pass-
word, hostname, management interface, loopback interface, and
backup router. Follow along and refer to the information that you
gathered in Chapter 1 to customize the setup of your device for your
network.
NOTE This booklet follows the convention of not always showing the
command prompt in displaying configuration mode command
examples.
TIP If you are new to JUNOS, or it has been awhile since you last config-
ured a new device, explore the [edit system] hierarchy as a reminder
of basic settings that you can configure:
[edit system]
root@juniper1# set system ?
Possible completions:
+ authentication-order Order in which authentication methods are invoked
> backup-router IPv4 router to use while booting
domain-name Domain name for this router
host-name Hostname for this router
> location Location of the system, in various forms
> login Names, login classes, and passwords for users

Chapter 2:Configuring the System Basics 13
> name-server DNS name servers
> ntp Network Time Protocol services
> radius-options RADIUS options
> radius-server RADIUS server configuration
> root-authentication Authentication information for the root login
> syslog System logging facility
time-zone Time zone name
<snip>
Root Authentication Password
The root account or user is a predefined user name in JUNOS. The root
user is by default the administrator or super user, who has absolute
permission to both configure and install software on a device.
JUNOS requires configuration of the root password before it accepts a
commit. On a new device the root password must always be a part of
the configuration submitted with your initial commit. Use the follow-
ing command to set up a plain text password for the root user.
set system root-authentication plain-text-password
New password: ######
Retype new password: ######
As you enter the password in plain text, JUNOS encrypts it immedi-
ately. You don’t have to tell JUNOS to encrypt the password as in some
other systems. Plain text passwords are therefore hidden and marked
as ## SECRET-DATA in JUNOS configuration listings (see Appendix
example).
BEST PRACTICE Strengthen security by only allowing root access from the console port:
set system services ssh root-login deny
Hostname
The hostname of the device provides its identification for many
purposes. JUNOS uses the configured hostname as part of the com-
mand prompt, to prepend log files and other accounting information,
as well as in other places where knowing the device identity is useful.
In this booklet we use the name juniper1, but you can choose some-
thing more descriptive:
set system host-name juniper1

Loopback Interface
The loopback interface supports many different network and opera-
tional functions and is an “always up” interface. For example, the
loopback interface assures that the device is reachable, even if some of
the physical interfaces are down, removed, or an IP address has
changed. In most cases, you always define a loopback interface.
JUNOS follows the IP convention of using lo0 as the loopback inter-
face’s identifier name. Refer to Chapter 1 as a reminder of what you
have chosen as the IP address of your loopback interface:
set interfaces lo0 unit 0 family inet address 192.26.0.110/32
NOTE See this chapter’s Introducing Interfaces section for more information
about the set interfaces command format.
ALERT! JUNOS requires that the loopback interface always be configured with
a /32 network mask (avoiding any unnecessary allocation of address
space).
You can configure as many addresses as you need on the lo0 interface,
so it’s good practice to make one address preferred:
preferred
Only unit 0 (unit is a reference to a logical channel on JUNOS inter-
faces) is permitted as the master loopback interface. If you want to add
more IP addresses to this, you simply configure them in the normal
way under unit 0, without the preferred option:
BEST PRACTICE On the lo0.0 interface, it is useful to have the IP address 127.0.0.1
configured, as certain processes such as NTP and MPLS ping use this
default host address:
The 127.0.0.1/32 address is a Martian IP address (an address invalid
for routing), so it is never advertised by the Juniper device.
NOTE Depending on your network configuration, you may also need an ISO
address for the IS-IS routing protocol:
set interfaces lo0 unit 0 family iso address 49.0026.0000.0000.0110.00

Management Interface
The management interface supports access to your device for autho-
rized users as well as management systems. Users can then connect to
the management interface over the network using standard utilities
such as SSH and telnet (set up in Chapter 3).
Many types of JUNOS platforms include a dedicated management
port on the front panel. For others, you can configure one of the
Ethernet ports to act as the management interface.
Platforms that use a network Ethernet interface for management
include the SRX100, SRX210, SRX240, and SRX650 Services
Gateways and the J Series Services Routers. A network interface can
be configured as being dedicated to out-of-band management or as
being shared by both management and network traffic.
MORE? Even though your device has a dedicated management port, you may
prefer to configure a network interface to carry management traffic.
For example, your organization may use this approach when cost
does not justify a separate management infrastructure. Find out how
to configure the EX Series Ethernet Switches with in-band
management by downloading the white paper Deploying EX-series
Switches in Branch Offices at www.juniper.net/us/en/products-
services/switching/ex-series/.
Dedicated Management Port
The dedicated management port supports out-of-band management
access with complete physical separation from network traffic within
your device. This approach limits access to your device, and thereby
the potential for problems. Further, because it only carries manage-
ment traffic, the management port is fully available to you for
analyzing and reacting to problems if your device happens to be
under attack.
How to set up the dedicated management port:
Configuration of the dedicated management port simply requires
assignment of the IP address that you want to use as the management
interface. The interface name that you use in the JUNOS command
depends upon the type of device that you are setting up.

The following example shows the command format to set up the
dedicated management port for an EX Series switch. The EX Series
Ethernet Switches use the interface name me0 as the name of the man-
agement port:
set interfaces me0 unit 0 family inet address 172.26.27.44/24
On other JUNOS devices the dedicated management port is named fxp0.
Table 2.1 outlines the assigned names of the dedicated management port
in various Juniper platforms. If you are using one of these other plat-
forms, substitute the interface name me0 with fxp0 in the above com-
mand statement.
Table 2.1 Names of Dedicated Management Ports
Platform Dedicated Management Port
EX Series Ethernet Switches me0 (see note at the top of next page)
M, MX, and T Series Routers fxp0
SRX5xxx and SRX3xxx Services Gateways fxp0
MORE? Turn to the J Series documemtation for more about its management
interface as www.juniper.net/techpubs.
NOTE The EX Series also includes a commonly used virtual management
interface known as vme that is used for managing devices grouped
together in a virtual chassis. For more information check the availability
of Day One: Configuring EX Series Ethernet Switches at www.juniper.
net/dayone.
Management Over a Network Interface
If your type of device uses a network interface for carrying management
traffic, you similarly need to configure it with the IP address that you
want to use as the management interface. The following example sets up
the management interface on a network interface which is dedicated to
out-of-band management. The Appendix outlines how to set up man-
agement on a shared network interface.

The following section discusses how to configure the management
interface on a branch SRX Series device or J Series in flow-based mode.
How to set up management on a dedicated network interface with zones:
1. Configure the interface with the IP address that you are using for
management:
set interfaces ge-0/0/0 unit 0 family inet address
172.26.27.44/24
2. Before the interface can carry traffic, you must assign the configured
management interface to a zone. The zone provides virtual separation
of traffic and acts as a policy enforcement point. The functional zone
management is a special predefined zone for out-of-band management in
these platforms. Add the logical interface to this zone with the
following command:
set security zones functional-zone management interfaces ge-
0/0/0.0
3. Where you have set up a functional zone, it is necessary to specify
which protocols the interface responds to, for example:
set security zones functional-zone management host-inbound-
traffic system-services ssh
MORE? Learn more about functional and security zones in the Security Con-
figuration Guide available at www.juniper.net/techpubs.
Backup Router
You can configure JUNOS to use a backup router during the initial
boot process in Layer 3 devices. The JUNOS process responsible for
establishing routes (among other functions) is known as the routing
protocol daemon (RPD). When JUNOS is booting, RPD is not initially
running, and therefore the device has no routes. Configuring a backup
router allows the device to establish a Layer 3 connection during boot
time, thereby minimizing the amount of time the device is unavailable.
set system backup-router 172.26.31.1 destination 172.16.0.0/12
In this example, if you choose the default gateway of your manage-
ment system, the management network (all of the IP range 172.16/12)
is reachable via next-hop 172.26.31.1 early on in the boot process,
even before other routing protocols have converged.

NOTE JUNOS only uses the backup router during the boot sequence. If you
want to configure a backup router for use after startup, you can set up
a default route as discussed in Day One: Configuring JUNOS
Interfaces and Routing found at www.juniper.net/dayone.
Reaching a Domain Name System (DNS) Server
JUNOS can resolve hostnames to IP addresses if it knows the location
of your DNS server(s). The approach is similar to the way Web
browsers resolve the names of a Web site to its network address.
Additionally, JUNOS lets you configure one or more domain names
which it uses to resolve hostnames that are not fully qualified (i.e., the
domain name is missing). This is convenient as you can simply use a
hostname in configuring and operating JUNOS without the need to
reference the full domain name.
SHORTCUT After adding a DNS server(s) and domain name(s) to your JUNOS
configuration, you can use DNS resolvable hostnames in your configu-
ration and commands instead of IP addresses.
How to configure the DNS server:
1. Begin by including the IP address(es) of your DNS server(s) within a
name-server statement(s):
set system name-server 172.26.27.2
set system name-server 172.26.27.3
2. It’s good practice to configure the domain name in which the device
itself is located. JUNOS then uses this configured domain name as the
default domain name to append to hostnames that are not fully
qualified:
set system domain-name enterprise.com
3. If your device can reach several different domains, you can configure
these as a list of domains to be searched. JUNOS then uses this list to
set an order in which it appends domain names when searching for the
IP address of a host.
set system domain-search [enterprise.com department.enterprise.com]
This command example configures JUNOS to search the enterprise.
com and then the department.enterprise.com domains when
attempting to resolve unqualified hosts.

VERIFY If you have configured your DNS server with the hostname and an IP
address for your JUNOS device, you can issue the following commands
to confirm that DNS is working and reachable.
In the first command use the IP address of your device to confirm
resolution to the configured hostname.
root@juniper1> show host 172.26.27.44
44.27.26.172.in-addr.arpa domain name pointer juniper1.enterprise.com.
In the second command, use the configured hostname to confirm
resolution to the IP address.
root@juniper1> show host juniper1
juniper1.enterprise.com has address 172.26.27.44
NOTE It doesn’t matter which IP address you assign as the address of your
JUNOS device in the DNS server, as long it is an address that reaches
your device. Here we have used the management interface, but you may
choose the loopback interface, a network interface, or even configure
multiples of the addresses on the DNS server.
Setting Up the Date andTime
The initial configuration of a device should include time settings for
accurate recording of events. To set the time in your JUNOS device, you
can either configure it manually, or your device can take a system time
from an NTP (Network Time Protocol) server.
How to set time locally:
If you do not have access to an NTP you may configure JUNOS to keep
its own local time using an onboard clock. You can manually configure
the date and time from the JUNOS operational mode:
root@juniper1> set date 200901011200.00
The date is in the form (YYYYMMDDhhmm.ss).
How to use a remote time server:
In large networks it’s useful to have an NTP server to set the exact same
time across all the network devices. The common reference lets you
correlate all timestamps of logs and trace files for troubleshooting
purposes.
Use the following steps to configure your device to use one or more NTP
servers.

1. The easiest way to have NTP set the time is to have JUNOS retrieve the
time when it first boots up. Use the following command with the IP
address of your NTP server:
set system ntp boot-server 172.26.27.4
2. To keep the device synchronized with periodic updates, configure a
reference NTP server (you can configure more than one). It’s good practice
to do this, as the JUNOS device can be up for a long time, and therefore
the clock can drift:
set system ntp server 172.26.27.4
3. Next, you may want set the local time zone to match the device’s
location (note that Universal Coordinated Time (UTC) is the default). This
allows JUNOS to present the time in the correct local format, accounting
for things such as offset from UTC, which may change several times
throughout the year:
set system time-zone Europe/Amsterdam
TIP Many administrators prefer to keep all their devices configured to use the
UTC time zone. This approach has the benefit of allowing you to easily
compare the time stamps of logs and other events across a network of
devices in many different time zones.
4. If you’ve just booted JUNOS and need to synchronize time with a
remote time source, you can do so in operational mode:
root@juniper1> set date ntp 172.26.27.4
7 Apr 10:32:27 ntpdate[4544]: step time server 172.26.27.4 offset -0.000565 sec
How to verify your time settings:
After you set up the time, you can check the configuration in the following
ways.
VERIFY Check the system time at any time (pardon the pun):
root@juniper1> show system uptime
Current time: 2009-04-06 15:36:10 CEST
System booted: 2009-03-27 12:56:33 CET (1w3d 01:39 ago)
Protocols started: 2009-03-27 12:58:04 CET (1w3d 01:38 ago)
Last configured: 2009-04-06 15:27:02 CEST (00:09:08 ago) by username
3:36PM up 10 days, 1:40, 1 user, load averages: 0.00, 0.00, 0.00

This listing not only provides the current time, but also when the
device was last booted, the protocols started, and when the device was
last configured.
You can also check the NTP server status and associations of the
clocking sources used by your device with the two following com-
mands:
root@juniper1> show ntp associations
remote refid st t when poll reach delay offset jitter
==============================================================================
*172.26.27.4 203.26.24.6 3 u 16 64 377 0.256 -0.164 0.022
root@juniper1> show ntp status
status=0644 leap_none, sync_ntp, 4 events, event_peer/strat_chg,
version=”ntpd 4.2.0-a Wed Mar 25 07:21:19 UTC 2009 (1)”,
processor=”i386”, system=”JUNOS9.4R2.9”, leap=00, stratum=4,
precision=-19, rootdelay=502.545, rootdispersion=74.632, peer=59484,
refid=172.26.27.4,
reftime=cd847de9.ccb54775 Mon, Apr 6 2009 15:11:05.799, poll=6,
clock=cd847dfc.4a08cfa9 Mon, Apr 6 2009 15:11:24.289, state=4,
offset=-0.164, frequency=52.814, jitter=0.030, stability=0.005
Introducing Interfaces
The interfaces available in JUNOS devices include physical interfaces
for moving traffic in and out of the device, as well as special interfaces
such as the management and loopback interfaces (see the prededing
Management Interface and Loopback Interface sections).
As part of the basic setup of a device, this section discusses the format
of the interface naming, introduces logical interfaces, and shows how
to configure a Gigabit Ethernet interface.
MORE? Day One: Configuring JUNOS Interfaces and Routing discusses how
to configure other types of interfaces. Check availability and download
your copy at www.juniper.net/dayone.
Physical Interface Naming
Your platform may include Ethernet interfaces for carrying traffic and
one or more of many wide area network interfaces available on
different types of JUNOS devices. Regardless of the type of interface,

JUNOS follows a standard format in its interface naming. The inter-
face name is made up of two parts: the interface type and the interface
numbering.
JUNOS denotes the different types of interfaces with a text identifier.
For example, the identifier for a Gigabit Ethernet interface is the text
string ge.
The Juniper engineers assign interface numbers corresponding to each
interface location (in each hardware platform). Generally, they use the
following conventions in designating numbers to the device interfaces,
sequentially assigning numbers beginning with 0.
n slot: the first number corresponds to the slot location. On small
platforms, fixed interfaces are usually assigned as being in slot 0.
In high end platforms, physical slots exist to hold a Flexible PIC
Concentrator (FPC), which is a large board that can in turn hold
many interface cards.
n PIC: the second number corresponds to the Physical Interface Card
(PIC) position within the slot.
n port: the third number corresponds to the port number on the PIC.
Putting it all together, an example of an interface name is ge-0/0/1. In
this example, the type of interface is Gigabit Ethernet, the slot number
is 0, the PIC number is 0, and the port number is 1.
TIP The port number is also written on the PIC itself, which is useful when
you’re juggling multiple FPCs and PICs.
Try It Yourself: Viewing the Hardware Configuration
Try entering the following operational mode command on your device to determine its physical
configuration:
root@juniper1> show chassis hardware
Logical Units
In setting up your network you may want to partition a physical
interface into multiple logical interfaces – for instance, subdividing an
Ethernet interface into multiple virtual LANs (VLANs). JUNOS refers

to these logical interfaces as units. Typically JUNOS requires that you
set up one (or more) logical units on each physical interface.
In naming the logical interface, JUNOS simply appends the logical unit
to the physical port. If we added a logical unit (also sometimes referred
to as a channel) of 0 to our example above, the complete interface
name would become: ge-0/0/1.0.
NOTE Other vendors refer to logical interfaces on their platforms as sub-
interfaces.
Gigabit Ethernet
The best way to learn how to configure interfaces in JUNOS is to
present an example. Let’s say that you want to configure the Gigabit
Ethernet interface ge-0/0/1. Use the set interfaces command,
specifying the IPv4 address 192.168.100.1/30:
set interfaces ge-0/0/1 unit 0 family inet address 192.168.100.1/30
Looking at the levels of the command more closely:
n ge-0/0/1 is the name of the Gigabit Ethernet physical interface.
n unit 0 is a logical unit configured within the physical interface.
Each physical interface must have at least one configured logical
interface, with the first one numbered 0 (not 1) before it can carry
traffic.
n family inet identifies the protocol used by the logical interface. You
almost always want to configure at least one family on each logical
interface. In this booklet, all of our configurations use inet which
is how JUNOS refers to IPv4.
n address 192.168.100.1/30 is the address of the logical interface.
Each logical interface can support multiple addresses. So
configuring additional addresses does not override existing
addresses.
VERIFY Show that the Gigabit Ethernet interface has been set up:
root@juniper1# show interfaces
ge-0/0/1 {
unit 0 {
family inet {
address 192.168.100.1/30;
}
}
}

ReviewingYourWork
With the essential basics now set up in your device, you may want to
review your work. First, commit your configuration. Then, you can
compare your listing to the configuration defined by the commands
designated by an arrow ►. The full configuration is available in the
Appendix of the PDF version of this Day One booklet.
Use the show configuration command in operational mode to see
what’s in your active configuration after completing the commit. If
you’ve been following along in your own device, your configuration
should include the following statements for the ge-0/0/1 interface:
root@juniper1> show configuration interfaces ge-0/0/1
unit 0 {
family inet {
address 192.168.100.1/30;
}
}
How to display the active configuration as a series of set commands:
You can also easily convert the displayed listing into the original set
commands by piping the output into the | display set modifier. This
makes it easier for you to see which commands created the configura-
tion:
root@juniper1> show configuration interfaces ge-0/0/1 | display
set
192.168.100.1/30
NOTE JUNOS displays the show configuration | display set listing from
the top of the configuration mode, i.e. the set commands are in the
form that you would use at the [edit] hierarchy level of the configura-
tion.
TIP When looking at output with operational mode show commands, you
can display more information by using the detail or extensive
keywords.

Chapter 3
Setting Up UserAccounts
Creating Login Banners. . . . . . . . . . . . . . . . . . . . . . . . . . .26
Conﬁguring LoginAccounts . . . . . . . . . . . . . . . . . . . . . . . .27
Setting Up RemoteAuthentication . . . . . . . . . . . . . . . . . .29
Enabling RemoteAccess . . . . . . . . . . . . . . . . . . . . . . . . . .31
CommittingYour Changes . . . . . . . . . . . . . . . . . . . . . . . . .32

JUNOS offers a rich and flexible set of features for configuring and
managing user accounts, authentication, and permissions. This chapter
gives you what you need on day one, as well as a few references for when
you are ready to take advantage of the more advanced capabilities of
JUNOS Software.
Creating Login Banners
You can create login banners for those who post messages and an-
nouncements to those who access the device. You might want to config-
ure an initial login message now, before you create any user accounts.
Login Message
A login message displays a banner to all users when they access the
device, before they log in. The message can be split over multiple lines
by using n (newline, equivalent to a carriage return and line feed) as a
delimiter:
set system login message “ Welcome n to n JUNOS Trainingn “
After you set up the message above, any user accessing your device sees
it displayed on their screen. For example, if the remote client is using the
Secure Shell (SSH):
$ ssh juniper1
Welcome
to
JUNOS Training
root@juniper1’s password:
TIP Use the login message to warn others that unauthorized access to your
device is prohibited (ask your legal department for the preferred state-
ment in your organization):
set system login message “WARNING: Unauthorized access is an
offense”
LoginAnnouncement
Sometimes you want to make announcements only to authorized users
after they have logged in. For example, you may want to announce an
upcoming maintenance event. Use the set system login announcement
command when you want to restrict your announcement to only
authorized users:
set system login announcement “Maintenance scheduled 11PM to 2AM
tonight”

Chapter 3:Setting Up UserAccounts 27
Configuring LoginAccounts
JUNOS requires that all users have a predefined account before they
can log in to the device. Further, you can configure the login accounts
to restrict who has access to what on your device. The accounts can be
set up with a local user and password, as well as with local users and
user templates that depend upon remote servers to provide authentica-
tion either using the RADIUS or TACACS+ protocols (discussed later).
Local User and Password
Set up local users with a name and password with the following steps,
and then add their user class in the next section.
1. To begin setup, navigate to the [edit system login] section of the
configuration:
[edit]
root@juniper1# edit system login
[edit system login]
root@juniper1#
2. Add a new user using their assigned account login name. This
example creates a new user with username jadmin:
[edit system login]
root@juniper1# edit user jadmin
3. You can also configure a full descriptive name for the account. If the
full name includes spaces, enclose the entire name in quotes:
[edit system login user jadmin]
root@juniper1# set full-name "Juniper Network Administrator"
4. Set the user identifier (UID) for the account. As with Unix systems,
the UID enforces user permissions and file access. If you don’t set the
UID yourself, JUNOS assigns one for you. The format of the UID is a
number in the range of 100 to 64000. To set a UID:
root@juniper1# set uid 1250
5. Create a password for the user. As discussed in Chapter 2, you use
the set command to create a password as plain text, and JUNOS
internally encrypts it:
root@juniper1# set authentication plain-text-password
New password: ####
Retype new password: ####

By default, JUNOS locally authenticates all users who try to log into
the software using the accounts provided in the configuration.
MORE? The user (and root) passwords can also be locally configured as
encrypted passwords. Find out how to set these up in the Configuring
User Accounts section of the Systems Basics Guide available at www.
juniper.net/techpubs.
Login Classes
In addition to the user name and password, all user accounts require
configuration of a login class. The login class defines the permissions
for executable commands. As users enter commands in the command
line, JUNOS checks the login class permission level for each command
before accepting it. JUNOS comes with four pre-defined user login
classes:
n super-user: all permissions
n operator: clear, network, reset, trace, and view permissions
n read-only: view permissions
n unauthorized: no permissions
For the new user created in the example above, set the login class as
super-user. You should always have at least one super-user set up
locally in the device:
root@juniper1# set class super-user
How to set up custom login classes:
If you need more detailed permissions than are provided by the four
default classes, you can create your own custom login classes. You can
specify exactly which commands you want to include or exclude for
each custom login class. In this way, you can create user classes tailored
to the specific needs of each particular user group.
1. For example, you may want to create a custom login class just for
network operations staff that you call netops:
set system login class netops

2. For each login class you can specify which permissions you want to
allow or deny, but this example keeps things simple by giving the netops
class access to everything:
set system login class netops permissions all
MORE? To find out more about user classes, including how you can set up your
own user classes, see the chapter Configuring User Access in the System
Basics Configuration Guide at www.juniper.net/techpubs.
Setting Up RemoteAuthentication
It’s common practice to use remote authentication servers to centrally
store information about users (see Chapter 1). You can configure
JUNOS to use one or more remote authentication servers, including
RADIUS and TACACS+ servers.
To set up remote authentication in your JUNOS device, you need to
configure the access to the server, the authentication order, and the local
user accounts. Several options are available for mapping users authen-
ticated by remote servers to the locally defined user accounts of the
device.
The following examples include the method of using the remote tem-
plate account. The username remote is a special case in JUNOS. It acts
as a template for users who are authenticated by a remote RADIUS or
TACACS+ server, but do not have a locally-configured user account on
the device. In this method, JUNOS applies the permissions of the remote
template to those authenticated users without a locally defined account.
All users mapped to the remote template are of the same login class.
NOTE Another method for mapping remotely authenticated users is to set up a
common shared account for all users of the same user class. Use this
method when you need more than one type of template for remote
users. See Creating a Local Template Account in the Administration
Guide of JUNOS documentation at www.juniper.net/techpubs.
How to start the configuration for authentication by a RADIUS server:
Use the following steps to start the set up of user authentication by a
RADIUS server. Complete the set up with steps 3 and 4 below.

1. Enter the RADIUS configuration statement:
set system radius-server 172.26.27.5
2. You can also include a shared secret in the command statement and,
if necessary, the port number:
set system radius-server 172.26.27.5 port 1845
set system radius-server 172.26.27.5 secret Jun1p3r
How to start the configuration for authentication by aTACACS+ server:
Use the following steps to start the set up of user authentication by a
TACACS+ server. Complete the set up with steps 3 and 4 below.
1. Enter the TACACS+ configuration statement:
set system tacplus-server 172.26.27.6
2. You can also include a shared secret, and if necessary the port
number, in the command statement:
set system tacplus-server 172.26.27.6 port 49
set system tacplus-server 172.26.27.6 secret Jun1p3r
How to specify the login methods:
3. Specify the order in which JUNOS should attempt authentication:
set system authentication-order [ radius tacplus password ]
The above example assumes your network includes both RADIUS and
TACACS+ Servers. Nonetheless, youmust include this command as
part of the steps toconfigure the RADIUS and/or TACACS+ configu-
rations. In this example, whenever a user attempts to log in, JUNOS
begins by querying the RADIUS server for authentication. If it fails, it
next attempts authentication with the TACACS+ server, and finally the
locally configured user accounts.
ALERT! If the password option is not set (and the authentication server(s) are
available), JUNOS does not make an attempt to authenticate with
local passwords.
How to complete the configuration for authentication by a remote server:
4. Each user needs a locally defined username (such as adminjlk in this
example), or you can establish the default remote user. If a given
authenticated user name is not found locally on the device, then it
defaults to the settings of the remote template:

set system login user adminjlk class super-user
set system login user remote class super-user
How to verify the configuration of remote authentication server(s):
1. If all is correct on the server, you should see the following messages in
the syslog message file. Note that in order to use this verification you
need to first configure system logging, as described in Chapter 5:
root@juniper1> show log messages
Apr 22 13:38:58 juniper1 sshd[17859]: Accepted password for adminjlk from 172.30.48.10
port 61729 ssh2
If the user has no login on the RADIUS server, the message logs include
the error message:
Apr 22 13:40:57 juniper1 sshd[17873]: Failed password for username from 172.30.48.10
port 64844 ssh2
2. You can also show the SSH session connections:
root@juniper1> show system connections
Active Internet connections (including servers)
Proto Recv-Q Send-Q Local Address Foreign Address (state)
tcp4 0 48 172.30.53.101.22 172.30.48.10.61729 ESTABLISHED
Enabling RemoteAccess
SSH, telnet, and FTP are widely-used standards for remotely logging into
network devices and exchanging files between systems. Before autho-
rized users can access your device, or your device can exchange data with
other systems, you must configure one or more of these enabling services.
They are all disabled by default in JUNOS.
SSH is telnet’s successor and is the recommended method for remote
access. SSH encrypts all traffic, including passwords, to effectively
eliminate eavesdropping, connection hijacking, and other attacks. The
SSH utility includes SCP (secure copy), a file transfer program that uses
SSH and is the recommended method for secure file exchange.
Use the following commands to set up the services that are needed in
your device:
set system services ftp
set system services telnet
set system services ssh

BEST PRACTICE Since both telnet and FTP are legacy applications that use clear text
passwords (therefore creating a potential security vulnerability), it’s
recommended that you use SSH (and SCP). If you don’t intend to use
FTP or telnet, it’s not required to configure them on your device.
However, don’t forget to consider that some users may use FTP to store
configuration templates, retrieve software, or other administrative
tasks.
CommittingYour Changes
Before leaving this chapter, don’t forget to commit your work so that it
becomes a part of the active configuration.

Chapter 4
Configuring SNMP
Configuring SNMP Communities . . . . . . . . . . . . . . . . . . .34
Configuring SNMPTraps. . . . . . . . . . . . . . . . . . . . . . . . . 37
Applying the Configuration Group. . . . . . . . . . . . . . . . . . .38
Configuring SNMP System Details . . . . . . . . . . . . . . . . . .39
ConfiguringView BasedAccess Control . . . . . . . . . . . . . . .40
CommittingYour Changes . . . . . . . . . . . . . . . . . . . . . . . . .42

At this point, configuration of the base system and users is completed,
so the next two chapters move on to basic configuration of the man-
agement functions in your device. Chapter 4 discusses how to config-
ure Simple Network Management Protocol (SNMP), and Chapter 5
introduces additional management tools. The Day One goal is to
integrate your new JUNOS device into your existing network manage-
ment infrastructure as quickly and easily as possible.
Because many network management systems are currently based on
SNMP, support for that protocol is a key feature of any network
device’s instrumentation.
JUNOS includes an onboard SNMP agent to provide remote manage-
ment applications with access to a variety of detailed information. The
SNMP agent in JUNOS supports SNMPv1, SNMPv2c, and SNMPv3
protocols, thereby enabling interoperability with a majority of the
management applications on the market today. A set of both industry-
standard and enterprise-specific management information bases
(MIBs) are available.
ALERT! By default, JUNOS ships with the SNMP agent disabled. Follow the
steps of this chapter to set up SNMP in your device.
Configuring SNMP Communities
Configuring the SNMP agent in JUNOS is a straightforward task that
shares many familiar settings common to other managed devices in
your network.
For example, you need to configure JUNOS with an SNMP community
string and a destination for traps. Community strings are administra-
tive names that group collections of devices (and the agents that are
running on them) together into common management domains (see
Chapter 1). Basically, if a manager and an agent share the same
community, they can talk to one another.
An SNMP community defines the level of authorization granted to its
members, such as which MIB objects are available, which operations
(read-only or read-write) are valid for those objects, and which SNMP
clients are authorized, based on their source IP addresses.

Chapter 4: Configuring SNMP 35
Try It Yourself: Getting Online Help
Before you begin, look at the online help available in operational mode as it relates to SNMP.
Find out what configuration options JUNOS supports in your software version:
jadmin@juniper1> help reference snmp community
Get more detailed usage guidelines for a topic or configuration statement:
jadmin@juniper1> help topic snmp community
Finally, get a list of all the JUNOS Software commands where SNMP statements occur:
jadmin@juniper1> help apropos snmp
Configuration Groups
Make things easier for yourself by placing your common SNMP
configuration settings inside a JUNOS configuration group (see
Chapter 6). Not only does a configuration group help to keep all your
customized configuration statements in one place, it also helps you to
copy templates between devices later on.
To create a new configuration group that you name common, enter the
following in configuration mode:
edit groups common
You can now add your SNMP configuration statements to the common
group and later apply them where you want in the configuration.
NOTE The examples in Chapters 4, 5, and 6 use jadmin as the user account.
How to create a read-only SNMP community:
1. Refer to what you recorded in Chapter 1 as the community string of
the SNMP community used in your network. This example uses the de
facto standard name public to create a community that gives limited
read-only access:
[edit groups common]
jadmin@juniper1# set snmp community public

2. Now focus your configuration statements onto this new branch of
the configuration hierarchy:
edit snmp community public
3. Define the authorization level for the community:
[edit groups common snmp community public]
set authorization read-only
In the above command you are confining the public community to
read-only access. Now any SNMP client (for example, an SNMP
management system) that belongs to the public community can read
MIB variables but cannot set (change) them.
4. Define a list of clients in the public community who are authorized
to communicate with the SNMP agent in JUNOS. List the clients by IP
address and prefix. Typically the list includes the SNMP network
management system in your network, or the address of your
management network. The following statement defines the network
192.168.1.0 (and any host within it) as being authorized:
set clients 192.168.1.0/24
5. Define the clients that are not authorized within the public
community by specifying their IP address, followed by the restrict
statement:
set clients 0.0.0.0/0 restrict
How to create a read-write SNMP community:
You can also define a community whose members have read-write access
to the JUNOS device.
1. If you are following along from the previous example, go back up
one level in the configuration hierarchy in order to create a new
community. You also want to place this new community inside the
JUNOS configuration group called common. Check that you are in this
branch of the configuration by the edit banner:
jadmin@juniper1# up
[edit groups common snmp]
jadmin@juniper1#
2. This example uses the de facto standard community string private
to identify the community granted read-write access to the SNMP
agent running on the device:

edit community private
3. Use the following commands to set the authorization level, set the
clients, and to specify the IP address for those with authorized access:
set authorization read-write
set clients 192.168.1.15/24
set clients 0.0.0.0/0 restrict
NOTE A later section discusses how to control access to specific branches of
the SNMP MIB tree by defining MIB views and assigning them to
SNMP communities.
Configuring SNMPTraps
Traps are unsolicited messages sent from an SNMP agent to remote
network management systems or trap receivers. Many enterprises use
SNMP traps as part of a fault-monitoring solution, in addition to
system logging (see Chapter 5). In JUNOS, SNMP traps are not
forwarded by default, so you must configure a trap-group if you wish
to use SNMP traps.
How to configure a trap-group:
1. Create a single, consistent source address that JUNOS applies to all
outgoing traps in your device. A source address is useful, because
although most JUNOS devices have a number of outbound interfaces,
using one source address helps a remote NMS to correlate the source
of the traps to an individual device:
jadmin@juniper1# edit groups common snmp
[edit groups common snmp]
jadmin@juniper1# set trap-options source-address lo0
The above commands place the statement inside the common config-
uration group that you have defined. It uses the IP address of the
loopback interface lo0 (see Chapter 2) as the source address for all
the SNMP traps that originate from the device.
2. Create a trap-group where you can list the types of traps to be
forwarded and the targets (i.e., addresses) of the receiving remote
management systems:
set trap-group managers version v2 targets 192.168.1.15

The above command creates a trap-group called managers which
allows SNMP version 2 formatted notifications (i.e., traps) to be sent
to the host at address 192.168.1.15. This statement forwards all
categories of traps.
3. Use the categories statement to define the specific subset of trap
categories to be forwarded.
set trap-group managers version v2 targets 192.168.1.15
categories authentication
Table 4.1 lists a variety of trap categories used in JUNOS.
Table 4.1 JUNOS SNMPTrap Categories
Configuration Option MIB Description
authentication Standard MIB-II Authentication failures on the agent (the device)
chassis Juniper proprietary Chassis and router environment notifications
configuration Juniper proprietary Configuration mode notifications
link Juniper proprietary
Interface transitions, such as transitioning from
up to down
rmon-alarm Juniper proprietary SNMP Remote monitoring events
routing Juniper proprietary Routing protocol notifications
startup Standard MIB-II Router reboots (soft/warm and full reboots)
Applying the Configuration Group
So far in this chapter you have been placing all of your SNMP configu-
ration statements inside a JUNOS configuration group named common.
And you’ve used a configuration group with the intention of making
things easier later on. At some point in the future you might want to
reuse the common statements elsewhere in the configuration, or copy
them to other devices.
Now, in order for the statements within the common configuration
group to be recognized by the JUNOS Software, you have to apply
them:

jadmin@juniper1# top
[edit]
jadmin@juniper1# set apply-groups common
This example applies the JUNOS configuration group called common at
the top of the configuration, so the group applies to all parts of the
configuration.
ALERT! Where you apply configuration groups within the configuration is
important, as only that specific hierarchy level (and below) inherits the
group statements. Further, the ordering of configuration groups is
important, as JUNOS inherits statements in the order that they are
applied.
VERIFY Have you committed the trap settings? If so, you can perform a quick
test to confirm that you have configured SNMP traps correctly. This
example generates an authentication failure trap (i.e., the SNMP agent
received a request with an unknown community), although other traps
types can also be spoofed:
jadmin@juniper1> request snmp spoof-trap authenticationFailure
Spoof-trap request result: trap sent successfully
Configuring SNMP System Details
You can use SNMP to store basic administrative details, such as a
contact name and the location of the device. Your management system
can then retrieve these remotely, when you’re troubleshooting a
problem or performing an audit. In SNMP terminology, these are the
sysContact, sysDescription, and sysLocation objects found within the system
group of MIB-2 (as per RFC 1213). You can set initial values directly
via a simple JUNOS configuration process.
How to set the system contact details:
1. Set the system contact details by including the contact statement in
the [edit snmp] hierarchy of the configuration, or under an
appropriate configuration group as explained above:
set contact “For help, please email support@enterprise.com”

2. Set the system description:
set description “Juniper EX4200”
3. Set the system location:
set location “London Corporate Office”
VERIFY After you have committed the configuration with these changes, you
can perform a quick test to confirm that you have entered the system
details correctly. Enter the following operational mode command:
jadmin@juniper1> show snmp mib walk system
sysDescr.0 = Juniper EX4200
sysObjectID.0 = jnxProductNameEX4200
sysUpTime.0 = 85957438
sysContact.0 = For help, please email support@enterprise.com
sysName.0 = junos
sysLocation.0 = London Corporate Office
sysServices.0 = 4
The show snmp mib walk system command performs a MIB walk-
through of the system table (from MIB-2 as per RFC 1213). The
SNMP agent in JUNOS responds by printing out each row in the table
and its associated value. You can use the same command to perform a
MIB walk-through of any part of the MIB tree supported by the agent.
ConfiguringView BasedAccess Control
SNMPv3 defines the concept of MIB views (so-called “View Based
Access Control,” see RFC 3415), which gives an agent better control
over who can access specific branches and objects within its MIB tree.
A view simply consists of a name and a collection of SNMP object
identifiers, which are either explicitly included or excluded. Once
defined, a view is then assigned to an SNMPv3 group or SNMPv1/v2c
community (or multiple communities), automatically masking which
parts of the agent’s MIB tree members of the group or community can
(or cannot) have access to.
How to create a MIB view:
Although most network management systems have recently started
using SNMPv3, a feature of the SNMP agent in JUNOS is that it
allows use of MIB views with both SNMPv1 and SNMPv2c communi-
ties. This example shows you how.

1. Enter the configuration mode of the JUNOS CLI and include the
view statement to create ping-mib-view:
set snmp view ping-mib-view oid 1.3.6.1.2.1.80 include
NOTE The oid statement does not require a dot at the beginning of the object
identifier.
The snmp view statement now includes the branch underneath the
object identifier .1.3.6.1.2.1.80 (i.e. the whole of the DISMAN-PING-
MIB subtree, as per RFC 2925), which effectively permits access to any
object under that branch.
2. Add a second branch in the same MIB view:
set snmp view ping-mib-view oid jnxPingMIB include
NOTE In this example, the object identifier is referred to by its object identity
name, rather than by its dotted oid number.
The additional snmp view statement extends the MIB view created
above, to include the Juniper Networks enterprise specific extensions
to the DISMAN-PING-MIB, which are located in the jnxPingMIB
branch (under .1.3.6.1.4.1.2636.3.7).
How to assign a MIBView to a community:
With the MIB view created, it is a simple task to assign it to the
appropriate community that you want to control. This example creates
a new community ping-mib which has read-write access to create
entries within the DISMAN-PING-MIB.
1. Give read-write access to the community as a whole:
set snmp community ping-mib authorization read-write
2. Associate the MIB view created earlier with the new community:
set snmp community ping-mib view ping-mib-view
Once you have committed the configuration, any member of the ping-
mib community now has read/write access to the branches that you
specified under ping-mib-view.

CommittingYour Changes
Commit your work and then you can go to the supplemental Appendix
included in the PDF version of this booklet to compare your conﬁgura-
tion to the provided example.

Chapter 5
Using Monitoring and Logging
Discovering the JUNOS Health Monitor . . . . . . . . . . . . . .44
Monitoring Devices Remotely . . . . . . . . . . . . . . . . . . . . . 45
Conﬁguring System Logs. . . . . . . . . . . . . . . . . . . . . . . . . .48
UsingWeb-Based Management . . . . . . . . . . . . . . . . . . . .53
ReviewingYourWork . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

In addition to SNMP, JUNOS offers other management tools, includ-
ing the JUNOS health monitor, remote monitoring, system logs, and J-
Web for web based management. Configuring these additional tools to
monitor and control your device completes your set up of the JUNOS
basics.
Discovering the JUNOS Health Monitor
Enterprise networks may include so many networked devices that it
becomes impractical to use a central network management system to
poll all of them. A more scalable approach is to rely on the network
devices themselves to notify the NMS when something requires
attention. JUNOS provides a useful mechanism called the health
monitor, allowing a device to monitor its own key operating metrics
and trigger alarms when normal operating parameters are exceeded.
The JUNOS health monitor uses the underlying remote monitoring
(RMON) mechanism (described in the next section) to monitor a
selection of predefined object instances, and to extend the basic
RMON functionality to support dynamic object instances. Examples
of predefined object instances are file system usage, CPU usage, and
memory usage. Dynamic object instances include software processes
and other entities that are only known at run time. Unlike standard
RMON, the JUNOS health monitor does not require device-specific
expertise in order to create a useful monitoring application. Once you
configure the health monitor, you can forget about it until it triggers an
event.
Both RMON and the JUNOS health monitor use the concept of rising
and falling thresholds to define an allowable operating range for an
object, as shown in Figure 5.1 on the next page. Each time a monitored
object crosses a threshold in Figure 5.1, it triggers an event. A rising
event raises an alarm and a falling event clears (or resets) an alarm.
This provides useful information that a remote NMS can act upon.
How to configure the JUNOS health monitor:
1. Add the health-monitor statement to the SNMP hierarchy of the
configuration:
[edit snmp]
set health-monitor

Chapter 5: Using Monitoring and Logging 45
Figure 5.1 RMON Thresholds
The configuration example uses the health-monitor defaults, setting
the rising threshold to 80%, the falling threshold to default to 70%,
and the polling interval to default to 300 seconds (5 minutes).
2. You can change the threshold values from the defaults. Set the rising
and falling threshold percentages to lower values and adjust the fre-
quency (in seconds) used by health monitor to check monitored objects:
[edit snmp health-monitor]
set rising-threshold 70
set falling-threshold 60
set interval 900
NOTE If you have enabled SNMP traps, health monitor generates RMON
rising and falling threshold events, and if you have enabled syslog, health
monitor uses the HEALTHMONITOR syslog tag.
Monitoring Devices Remotely
Many enterprises use the RMON capabilities of SNMP agents to
monitor aspects of their IP network. For example, your network may use
dedicated devices called RMON probes that analyze traffic for statistical
reporting. Or, perhaps it relies upon embedded agents on devices such as
IP routers and Ethernet switches. JUNOS provides an embedded RMON
agent capability, and supports the RMON alarm and event groups from
the Remote Network Monitoring MIB defined in RFC 2819.
RMON alarms and events are complementary to each other. You
configure alarms to tell the RMON agent to periodically take statistical
samples from a list of variables and compare them to thresholds. If a
Allowable
operational
range
Rising event
Value
Falling event Rising event
Falling threshold
Rising threshold

monitored variable crosses a threshold, JUNOS generates a corre-
sponding event, which sends a notification (SNMP trap or syslog
message) out from the device.
This section describes how you can configure RMON alarms and
events via the JUNOS CLI. Since the MIB groups are writable, if write
access is configured, an SNMP management system can also remotely
configure both alarms and events (see the View Based Access Control
section in Chapter 4).
For example, assume that you want to monitor the number of times
that remote hosts try to query the SNMP agent in JUNOS using an
incorrect community – which could indicate that someone is attempt-
ing something malicious, or that an NMS has been misconfigured. The
value is reported via SNMP with the snmpInBadCommunityNames object
(see the SNMPv2 MIB as per RFC 1907). Because it is an integer value,
it can easily be monitored by the RMON agent in JUNOS.
How to create an RMON alarm:
When you create an RMON alarm, you can also define alarm param-
eters, such as the object that you want to monitor, the monitoring
interval, and any thresholds, as well as the associated event.
1. Create an RMON alarm under the [edit snmp] configuration
branch:
[edit snmp]
set rmon alarm 100
2. Adjust the parameters of the RMON alarm:
[edit snmp rmon alarm 100]
set variable snmpInBadCommunityNames.0
set sample-type delta-value
set rising-threshold 100
set falling-threshold 90
set interval 900
set falling-event-index 100
set rising-event-index 100
In this example snmpInBadCommunityNames is a counter object, which is
incremented – every time the JUNOS device receives an SNMP request
with or for an unknown community. If the device receives more than

100 such requests in the last 900 seconds (15 minutes), the alarm
triggers event number 100 to run.
3. Now create the event associated with your alarm:
[edit snmp]
set rmon event 100
[edit snmp rmon event 100]
set community managers
set description “snmpInBadCommunityName threshold event”
set type log-and-trap
This event generates an SNMP trap whenever it is triggered, sending it
to the trap group managers. It also creates a new entry in the RMON
logTable (for details see RFC 2819). These entries can be useful if you
use an NMS to independently collect statistics about the number of
RMON events generated by the device over time.
VERIFY After committing your changes, you can perform a quick test to check
that you have entered the RMON alarm and event entries correctly.
Enter the following command from operational mode:
jadmin@juniper1> show snmp mib walk rmon
The show snmp mib walk rmon command performs a MIB walk through
the rmon table (per RFC 2819), printing out each row and its
associated value. You can use this same command to perform a MIB
walk through any part of the MIB tree supported by the JUNOS agent.
TIP You can troubleshoot the RMON operations by querying the contents
of the Juniper Networks enterprise RMON MIB, jnxRmon. The
Juniper MIB provides valuable information on alarm entries that fail
to trigger which, for example, might occur if an OID that was specified
in an alarm entry did not exist.
MORE? JUNOS can do much more than just generate an SNMP trap when an
event is triggered. For example, it can correlate multiple matching
events to remove duplicates, it can send a syslog message (see below),
and it can even perform a configuration change. If you want JUNOS to
perform more actions when an event is triggered, refer to JUNOS
Event Policy in the Configuration and Diagnostic Automation Guide
available at www.juniper.net/techpubs.

Configuring System Logs
System logs (often called syslogs) are Unix-style distributed event
reporting mechanisms that provide an extremely flexible method of
generating and handling event messages. Syslog was traditionally used
in Unix environments, with distributed hosts being configured to
forward their messages to one central syslog server called the log host.
Syslog messages are categorized by a facility to indicate the source of
the event and a level to indicate its severity. JUNOS can respond to
each event with a variety of actions based upon a combination of the
facility and level reported in the message. These actions include
displaying event messages locally, storing the messages locally, or
forwarding messages to a standard remote syslog server for real-time
or offline analysis by third party monitoring applications. Administra-
tors can send either all or selected JUNOS syslog event messages to a
central server for fault de-duplication and analysis.
TIP You can find out what syslog configuration options are supported by
the running version of JUNOS in your device by entering the following
operational command:
jadmin@juniper1> help reference system syslog
Syslog Destinations
JUNOS Software offers the flexibility to send syslog messages to a
variety of different destinations, as listed in Table 5.1.
Table 5.1 Syslog Destination Detail
Destination Description
console Display log messages on the device’s console.
file
Store log messages locally on the device’s hard disk. Typically log files are
stored under the /var/log directory.
host
Forward log messages on to another syslog server (typically another
JUNOS device or a Unix machine) for additional processing
user
Display log messages to a user on whichever pty (pseudo-teletype)
terminal they are logged in on.

You can forward messages to a combination of all four destinations, as
incorporated in the examples provided in this booklet.
Message Facilities and Levels
When setting up the system logging, you also choose which messages
to log, which facilities (sources) to use, and which levels (severities) are
important to your network.
JUNOS supports a number of syslog facilities to specify the software
process that generates each message. If you are unsure of which facility
you want to monitor, or you don’t know which facilities are important,
you can monitor them all and adjust them later.
Each facility can generate a number of different messages, each of
varying level, i.e., severity. For example, an informational message
denotes the occurrence of a non-critical event which does not require
immediate action, whereas a critical event from the same facility might
require immediate operator intervention. The full list of syslog levels
supported by JUNOS is shown in Table 5.2.
Table 5.2 Syslog Levels
Numerical
Level
Level Description
- none Disables logging of the associated facility to a destination
0 emergency
System panic or other condition that causes the software
component to stop functioning
1 alert
Conditions that require immediate correction, such as a
corrupted system database
2 critical Critical conditions, such as physical errors
3 error
Error conditions that generally have less serious consequences
than events in the emergency, alert, and critical levels
4 warning Conditions that warrant monitoring
5 notice
Conditions that are not errors but might warrant special
handling
6 info Events or non-error conditions of interest
7 any All (i.e. any) level of message from the facility

When you set the syslog level, you are defining a mask that specifies the
lowest level of log message that you want to handle. For example, if
you specify that you want to capture all log messages of warning level,
the JUNOS Software logs messages to that level and above, notifying
you of any error, critical, alert, and emergency level messages.
MORE? For general information about configuring syslog, see the technical
documentation manual System Basics Configuration Guide. For a full
list of all of the messages supported by JUNOS, refer to the System Log
Messages Reference. Both are available at www.juniper.net/techpubs/.
Sending Messages to a File
Now that you are familiar with syslogs and what they do in JUNOS,
the simplest and the most useful syslog configuration on day one is to
send messages to a local file. Storing messages locally can be useful if
you need to maintain an audit trail of messages, or if you want to store
messages for analyzing at another time.
How to configure a syslog file:
1. Enter the file statement in the [edit system syslog] hierarchy of
the JUNOS configuration:
jadmin@juniper1# edit system syslog file all-messages
[edit system syslog file all-messages]
jadmin@juniper1# set any warning
jadmin@juniper1# set authorization notice
This example creates a file called all-messages in the local directory /
var/log that stores messages from any facility at the level of warning
and above. It also stores authorization messages, such as user logins, at
the level of notice and above. JUNOS automatically rotates log files
and archives them periodically as they grow larger.
NOTE You can customize the archive behavior by altering the [system syslog
archive] setting in the JUNOS configuration—although that is not
necessarily a day one task.
2. After you have committed the configuration, you can view the log
messages that are stored in a local file in operational mode:
jadmin@juniper1> show log all-messages | last 10
Here the last command modifier requests only the last 10 lines (the
most recent 10 events) in the file all-messages to show on the screen.

Directing Messages to aTerminal
When messages are important and require immediate intervention by a
human operator, the best way to get the operator’s attention is to
display a message on their screen. JUNOS allows you to display
messages to a user if they are logged in and also to display messages on
the device’s console.
How to send messages:
To forward messages to a user use these configuration steps.
1. Enter the user name in the [system syslog user] hierarchy:
set system syslog user * any emergency
set system syslog user jadmin any critical
The first set command forwards any emergency log message to all
users, as indicated by the JUNOS wildcard character *. The second set
command forwards any critical level log message and above to the
screen on which the user jadmin is logged in. This can be an effective
way of forwarding important messages to administrators who are
located remotely.
2. Another option is to forward log messages to the screen attached to
the device’s console. The following example sends log messages from
any facility at the level of error and above to the device’s console:
set system syslog console any error
Forwarding Messages to a Remote Server
JUNOS can also forward syslog messages to one or more remote
devices. Since many enterprises use fault monitoring software to
receive and interpret syslog messages, it makes sense to configure your
device to not only report log messages locally, but also to forward
copies of each message to a remote fault monitoring system.
For example, suppose you have a device in your network named
loghost, which is running a third party fault monitoring system.
Simply specify the appropriate facilities and levels under the [edit
system syslog host] hierarchy of the configuration:
set system syslog host loghost any notice
This example forwards log messages from all the facilities at the level
of notice and above to the remote host called loghost.

Customizing Log Message Formats
Many enterprises use commercial fault monitoring software. These
software packages are capable of scaling to handle the huge volume of
syslog messages that all of the devices in an IP network can generate.
Typically such products parse all incoming messages, filtering them
through a rules-based engine in order to determine what actions to
take. While these systems can be very flexible, they can also be compli-
cated to configure.
JUNOS helps to make integration with third party fault monitoring
systems easier. You can customize log messages, thereby reducing the
amount of configuration and processing that is necessary at the
receiving end.
Prefixed Strings
Assume that your network has over 500 IP devices, all of which are
generating syslog messages. Some may be JUNOS devices, some may
be Unix servers, and some may be networking devices from other
vendors. Although most commercial fault monitoring applications can
parse syslog messages by using custom rules, creating vendor-specific
rules can be difficult and time consuming. One option is to prefix all
syslog messages that originate from JUNOS with a particular string,
thereby making it easier to remotely match and parse those messages.
Use this command to prefix the word JUNOS to each syslog message
before it is forwarded to the remote device loghost:
set system syslog host loghost log-prefix JUNOS
This adds a static prefix of JUNOS to each syslog message from the
device. The prefix now makes it much easier for a remote fault moni-
toring application to identify any log message coming from the device.
Including Priority Information
An event’s facility and severity level are together referred to as its
priority. However, while the priority is known to syslog servers, it is
not often visible in the message text itself. Because of this, it can be
difficult to determine the priority of a given message, especially if the
message is forwarded to a remote host or stored locally in a file along
with messages of other priorities.
You can insert the event priority into the message text by including the
explicit-priority statement in the [system syslog host] or [system
syslog file] hierarchy:

set explicit-priority
The explicit-priority statement inserts the priority in the form
FACILITY-LEVEL into the beginning of each message. Note that in
this case, the level is a numerical value as previously listed in Table 5-2.
Facility Override
Some third party syslog monitoring applications “listen” to messages
arriving with a specific facility. Since JUNOS can generate messages
from many different facilities, some of which may be unknown to the
remote system, it is sometimes useful to override the original value to
ease integration.
To override the original syslog facility, use the facility-override
statement when configuring the syslog host:
[edit system syslog host loghost]
jadmin@juniper1# set facility-override local7
BEST PRACTICE In general, it makes sense to specify an alternate facility that is not
already in use on the remote system, such as one of the “localX”
facilities. You must also configure the third party syslog application to
handle the messages in the desired manner.
MORE? Syslog is one of several mechanisms that log network events in JUNOS.
The other commonly used tool is trace logging (also known as traceop-
tions). Trace logging keeps track of specific processes, such as routing
packets sent and received. Traceoptions output is similar to debug
output in other systems. To learn about trace logging, refer to the
System Basics Configuration Guide available at www.juniper.net/
techpubs.
UsingWeb-Based Management
Many people prefer to use a web browser as the main application for
accessing their network devices to monitor, administer, and trouble-
shoot them. JUNOS features a rich web-based interface called J-Web for
you to use.
This section walks you through the basic steps that you need to know
on day one: how to check if J-Web is installed, how to install it, and
how to configure it.

Installing J-Web
J-Web is a commercial product that comes preinstalled on EX Series
Ethernet switches, J Series routers, and SRX Series services gateways.
On other platforms, such as the M Series and MX Series routers, you
need to obtain and install the software package to use it. This section
describes how you can obtain J-Web and install it.
How to check if J-Web is installed:
To find out if J-Web is preinstalled on your device and its version:
1. Run the following operational mode command:
jadmin@juniper1> show version detail | match Web
TIP The match statement supports regular expressions, making it a very
flexible way for you to reduce clutter in output.
If J-Web is installed, show version will report “JUNOS Web
Management” with a version number, and you can skip the rest of
this section and move to Configuring J-Web.
2. If J-Web is not installed, you have to obtain it and then install it.
It is important to determine which version of JUNOS you are running
and install the version of J-Web that matches exactly. The show
version command tells you what you need to know:
jadmin@juniper1> show version
Hostname: junos
Model: m10
JUNOS Software Release [9.4R2.9]
How to install the J-Web package:
Obtain the J-Web software package either from your reseller or
directly from the Juniper Networks support website www.juniper.net/
customers/csc/software under the JUNOS Software download
section.
JUNOS can also pull the package from a remote server if you specify
the location of the package as a URL with the request system
software command. The following example uses FTP as the protocol
to pull the package onto the JUNOS device:

jadmin@juniper1> request system software add ftp://ftp:secret@server/pub/junos/jweb-
9.4R2.9-signed.tgz
Installing package 'ftp://ftp:secret@server/pb/junos/jweb-9.4R2.9-signed.tgz' ...
Verified jweb-9.4R2.9.tgz signed by PackageProduction_9_4_0
Adding jweb...
Available space: 671134 require: 8226
Mounted jweb package on /dev/md9...
Verified manifest signed by PackageProduction_9_4_0
Executing /packages/mnt/jweb-9.4R2.9/mount.post..
Reloading /config/juniper.conf.gz ...
Activating /config/juniper.conf.gz ...
mgd: commit complete
Restarting mgd ...
Saving package file in /var/sw/pkg/jweb-9.4R2.9-signed.tgz ...
Saving state for rollback ...
WARNING: cli has been replaced by an updated version:
CLI release 9.4R2.9 built by builder on 2009-03-25 07:29:27 UTC
Restart cli using the new version ? [yes,no] (yes)
Restarting cli ...
jadmin@juniper1>
Configuring J-Web
With the J-Web package installed on your JUNOS device, you can go
ahead and configure it. Since J-Web is not configured and running by
default, you must complete its initial setup via the JUNOS CLI. This
is true for all JUNOS devices:
set system services web-management http
Once you have committed the configuration change you can access
the JUNOS Software via the J-Web interface. Simply enter the
hostname or IP address of the JUNOS device as a URL into a web
browser.
For further details on how to use the J-Web interface, refer to the J-
Web Interface User Guide, available online at www.juniper.net/
techpubs/. J-Web has differences for different devices, so be sure to
get the guide for your specific platform.

ReviewingYourWork
This chapter concludes the basic setup of your device. Chapter 6
provides you with additional commands and shortcuts that can ease
configuration moves, adds, and changes in your device.
If you followed along in your own device by entering the commands
designated by an arrow ►, your configuration should now match the
configuration listing provided in the Appendix of the PDF version of
this Day One booklet. Once again, the PDF is freely available at www.
juniper.net/dayone.

Chapter 6
Working with Configuration
Templates and Other Shortcuts
Displaying Set Commands . . . . . . . . . . . . . . . . . . . . . . . .58
Making Changes Faster . . . . . . . . . . . . . . . . . . . . . . . . . 59
Defining Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Using ConfigurationTemplates . . . . . . . . . . . . . . . . . . . . .65
SavingYourWork. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

This chapter provides some handy techniques that can save you a lot of
time when you are creating and modifying configurations in the
command-line interface. These techniques let you easily reuse configu-
ration statements set up in other parts of your configuration and even
in other devices. For example, you can use configuration groups to set
up and apply common elements that are reused within the same
configuration and configuration templates to load common elements
used in the configurations of different devices. These shortcuts can not
only speed configuration editing, but can also help reduce errors often
associated with repetitive command entry.
Several of the examples go beyond what you would typically do on day
one, but provide you with a preview to other powerful features within
JUNOS.
TIP In this booklet, the headings in the left margin are generally named
after the commands themselves, for easier look up.
Displaying Set Commands
One of the most frequently used and easiest configuration shortcuts is
displaying an existing set of commands known to work and then
reusing them somewhere else:
jadmin@juniper1> show configuration interfaces ge-0/0/1 |
display set
192.168.100.1/30
Regardless of where you specifically entered your set commands in the
configuration hierarchy, the show configuration | display set
command lists them as if they were entered from the top of configura-
tion mode. You can use the command to display the whole configura-
tion, or just a portion as shown in the above example.
In the displayed listing, look for the set command that you want to re-
use, and copy it using an available copy command such as the key-
board command Control+C. Then, move your cursor to where you
want to re-use the command, and paste it (you can use the keyboard
command Control+V). You can cut and paste the entire output (the
returns are embedded at the end of each line). Before you hit Enter you
can make any other changes needed in the command lines, such as
changing the IP address.

Chapter 6: Working with ConfigurationTemplates and Other Shortcuts 59
SHORTCUT You can combine the top command with other commands to enter new
statements at the top of the hierarchy, regardless of where you are
currently working in the configuration. Example:
top set interfaces ge-0/0/1 unit 0 family inet address
192.168.100.1/30
Making Changes Faster
Networks are complex, dynamic systems that may need to change
frequently in order to meet new business needs. Fortunately JUNOS
offers helpful commands to shorten the time that it takes to make
changes in the existing configuration.
Rename
Sometimes you may want to rename a section of the JUNOS configura-
tion, for example, to alter an older naming convention to adhere to a
new policy. Let’s assume you want to rename ge-0/0/0 to the new
naming convention of ge-1/0/0. Below is the current configuration
snippet:
jadmin@juniper1# show interfaces ge-0/0/0
unit 0 {
family inet {
address 100.100.100.1/24;
}
}
You can rename the interface in one step with the rename command:
jadmin@juniper1# rename interfaces ge-0/0/0 to ge-1/0/0
VERIFY The show command lets you check that the change has occurred:
unit 0 {
family inet {
address 100.100.100.1/24;
}
}
NOTE In this context, the JUNOS rename command acts in a similar way to
the Unix “mv” (move) command by renaming the original section
rather than making a copy of it.

Copy
JUNOS also allows you to make copies of parts of the conﬁguration by
using the copy command. For example, let’s assume that you created a
template for a local user called logintemplate, and now you want to
make a copy for a new user “joe” who has recently joined your team:
jadmin@juniper1# show system login user
user logintemplate {
full-name “Generate network operations user”;
class netops;
authentication {
encrypted-password “$1$Naeta3Iw$./sgTTPK0NoH0PJdsXvP6.”;
## SECRET-DATA
}
}
You can make a copy of this template for a new user “joe” by using the
copy command:
jadmin@juniper1# edit system login
jadmin@juniper1# copy user logintemplate to user joe
VERIFY Check that JUNOS has created the new local user:
jadmin@juniper1# show
user logintemplate {
full-name “Generate network operations user”;
class netops;
authentication {
## SECRET-DATA
}
}
user joe {
full-name “network operations user”;
class netops;
authentication {
## SECRET-DATA
}
}
To complete the setup of joe, you can modify his password, and he’s
ready to go.

Replace
Another useful command is replace, which changes a given character
string throughout the configuration to something else. For example,
assume that you have interface ge-0/0/0 referenced in the protocols
branch of the configuration because you have configured OSPF on it,
as shown below:
unit 0 {
family inet {
address 100.100.100.1/24;
}
}
jadmin@juniper1# show protocols ospf
area 0.0.0.0 {
interface ge-0/0/0.0;
}
In this example, you can use the replace command to rename the inter-
face to the new naming convention throughout the entire configura-
tion:
jadmin@juniper1# replace pattern ge-0/0/0 with ge-1/0/0
Insert
The insert command allows you to insert a configuration statement
either before or after an item in an ordered sequence. It is especially
useful if you are configuring firewall filters and routing policies and
need to change the ordering of terms. For instance, suppose you have
the following policy:
[edit policy-options policy-statement multiterm]
jadmin@juniper1# show
term reject {
then reject;
}
term accept {
from protocol bgp;
then accept;
}
Applying this to a BGP import or export policy would have it reject all
routes, because the terms are processed from the top down, and the

reject term is before the accept term. To adjust, use the insert
command:
[edit policy-options policy-statement multiterm]
jadmin@juniper1# insert term accept before term reject
You can insert before or after depending on the order needed for the
policy.
MORE? Learn more about configuring policies with the Policy Framework
Configuration Guide available at www.juniper.net/techpubs.
Defining Groups
For settings repeated in many parts of the configuration, such as
interface parameters, configuration groups let you streamline setup.
Configuration groups are sets of statements that you can apply to
multiple parts of the configuration. Use them to create smaller, more
logically constructed configuration files. Not only is initial setup faster,
but when you need to make a change, you can do it in one place, and
yet have it apply everywhere.
This booklet has previously shown how to set up a group for SNMP
management in Chapter 4. This section provides two examples of
using groups in the configuration of interfaces.
It’s important to remember that where you apply configuration groups
within the configuration matters, as only that specific hierarchy level
(and below) inherits the group statements. Further, the ordering of
configuration groups is important, as JUNOS inherits statements in the
order that they are applied.
Creating an Interface Group
Many wide area links are based on the optical SONET/SDH standard.
All of your SONET interfaces will require SDH framing, and need to
comply with parameters as defined by RFC 2615. Let’s assume you
have a SONET/SDH interface configured like this:
jadmin@juniper1# show interfaces so-0/0/0
unit 0 {
family inet {
address 192.168.1.1/30;
}
}

How to configure and apply the interface group:
These commands set up a group called sdh and apply it throughout the
configuration.
1. Configure the group and set the required parameters:
set groups sdh interfaces <so-*> framing sdh
set groups sdh interfaces <so-*> sonet-options rfc-2615
SHORTCUT The interfaces are configured as <so-*>. The <so-*> acts as a wildcard
for all SONET/SDH interfaces, so when it is applied, all interfaces
inherit these settings.
2. Now apply the group where you want it in the configuration. If you
enter the set apply-groups command from the top of the
configuration tree, the group is applied throughout the configuration.
set apply-groups sdh
ALERT! If you are using JUNOS configuration groups, by default the show
command only displays configurations under the specific branch in
which you are currently working. The listing does not show any
settings inherited from any configuration groups applied in other parts
of the configuration. For example, if you use the following show
command, you do not see the sdh group, even though you applied it:
jadmin@juniper1# show interfaces so-0/0/0
unit 0 {
family inet {
address 192.168.1.1/30;
}
}
TIP Pipe the show output through the display inheritance option to show
the full configuration with the applied sdh group.
jadmin@juniper1# show interfaces so-0/0/0 | display inheritance
##
## ‘framing’ was inherited from group ‘sdh’
##
framing {
##
## ‘sdh’ was inherited from group ‘sdh’
##
sdh;
}

##
## ‘sonet-options’ was inherited from group ‘sdh’
##
sonet-options {
##
## ‘rfc-2615’ was inherited from group ‘sdh’
##
rfc-2615;
}
unit 0 {
family inet {
address 192.168.1.1/30;
}
}
SHORTCUT Included comments may make the configuration difficult to read. Use
the except command to hide the comments from the listing:
jadmin@juniper1# show interfaces so-0/0/0 | display inheritance
| except ##
framing {
sdh;
}
sonet-options {
rfc-2615;
}
unit 0 {
family inet {
address 192.168.1.1/30;
}
}
How to exclude an apply-group:
The example in this section shows how to exclude a broadly-applied
group from specific sections of your configuration.
Let’s assume that your network uses the ISO and MPLS protocols in a
group applied at the top of the configuration. Doing this means that
you don’t need to configure these families under each interface. The
wildcard * notation is used to ensure the protocols are configured
thoughout:
groups {
isis-mpls {
interfaces {
<*-*> {
unit <*> {
family iso;
family mpls;

}
}
}
}
}
apply-groups isis-mpls;
Now let’s assume there are some interfaces where you don’t want these
protocols configured. For instance, you may not want to enable the
ISO or MPLS protocols on interfaces within an L3 VPN.
Use the apply-groups-except statement to exclude a broadly-applied
group within a specific part of the configuration:
set interfaces ge-0/0/0 apply-groups-except isis-mpls
Using apply-groups-except tells JUNOS to exclude the isis-mpls
group on the ge-0/0/0 interface, even though the isis-mpls group has
been applied at the top of the configuration.
MORE? For full details on applying configuration groups, refer to the section
on Configuration Groups in the CLI User Guide at www.juniper.net/
techpubs/.
Using ConfigurationTemplates
Let’s say you are working on a large network, where you are respon-
sible for installing and configuring 100 new Juniper Networks devices
(without the help of a management system), with only one 2-day
weekend to finish the job. Because most of the devices operate in the
same network, many of the configuration parameters are the same for
all of them. Instead of typing configuration data individually into each
device, it is possible for you to create a template configuration (full or
partial) that you can copy to other devices. Using a template saves
time and also reduces the risk of errors.
How to create a template:
The easiest way to create a template is to make a copy of an existing
configuration or part of a configuration. Use the save command to save
the candidate into a file, by providing a file name as an argument:
[edit]
jadmin@juniper1# edit groups common
[edit groups common]

jadmin@juniper1# save common-template
Wrote 23 lines of configuration to 'common'
This example creates a file called common_template that contains every-
thing under the [edit groups common] hierarchy, including a timestamp
and the opening groups statement. The file resides locally in the user's
home directory within the device: /var/home/jadmin.
TIP Saving the template to an FTP server makes it easier for other devices to
access it.
How to load a template:
If you have saved the configuration template locally as a file, you can use
the load command from the top of configuration mode to load it into the
device’s configuration:
[edit]
jadmin@juniper1# load merge common-template
load complete
In this example, the load command includes the merge argument, which
tells JUNOS to merge the current candidate configuration with the
contents of the loaded file. JUNOS adds the template statements, exactly
as you saved them, to the [edit groups common] hierarchy location of the
device configuration.
TIP The above example assumes that the template is stored locally as a file
called common-template. Alternatively, if the template was stored on a
remote FTP server, you would enter its location as a URL:
jadmin@juniper1# load merge ftp://user:password@server/junos/
templates/common-template
After loading the file, don’t forget to commit the new configuration.
SavingYourWork
This section presents more examples of ways to save the candidate or the
active configuration. It can be easy to forget which configuration files you
are saving, so the words candidate and active are underlined for quick
reference.
The commands in this section show you how to create a file of the entire
configuration or a portion of it, then save the file locally or on other
devices. Additionally, you can configure JUNOS to automatically save
the active configuration file at specific intervals or upon every commit.

MORE? Day One: Exploring the JUNOS CLI introduced the operational mode
file commands for uploading and downloading files from servers.
How to save a candidate file locally:
Every JUNOS user defined in the configuration has their own home
directory within the device in the form: /var/home/username. To save
the candidate configuration into your user home directory, simply save
to a filename in configuration mode.
jadmin@juniper1# save router-config
Wrote 206 lines of configuration to ‘router-config’
VERIFY You can check your home directory on the device using the file list
command from operational mode:
jadmin@juniper1# run file list
router-config
Use the file show command to view the actual contents of your saved
configuration file:
jadmin@juniper1# run file show router-config
<configuration file contents will be here>
How to save a portion of the candidate configuration:
Use the save command deeper in the configuration to save portions of
the candidate configuration as command blocks, and reuse these
command blocks in other devices in your network. For example, use
the same system login information for all the switches in the network.
[edit system login]
jadmin@juniper1# save system-login
Wrote 29 lines of configuration to 'system-login'
How to save a configuration file remotely:
The following example saves the entire candidate file to a remote server
called remot, using SCP (secure copy) to transport it:
[edit]
jadmin@juniper1# save scp://jadmin@remot
The authenticity of host ‘remot (172.26.25.4)’ can’t be established.
RSA key fingerprint is 13:ff:78:8a:fd:38:8f:d8:94:5e:39:9f:60:eb:9b:b5.
Are you sure you want to continue connecting (yes/no)? yes
Warning: Permanently added ‘remo,172.26.25.4’ (RSA) to the list of known hosts.
jadmin@remot’s password:
tempfile 100% 4482 4.4KB/s 00:00
Wrote 270 lines of configuration to ‘scp://jadmin@remot’

TIP If you want to save the active configuration, you can use the opera-
tional mode file copy command (refer to Day One: Exploring the
JUNOS CLI). Optionally, you can use a pipe to save the output of the
operational mode show command. The following command lets you
save the active configuration by creating a listing of the active configu-
ration, then piping into a save statement to create a locally-stored file
called Tuesday-archive:
jadmin@juniper1# run show configuration | save Tuesday-archive
Wrote 115 lines of configuration to ‘Tuesday-archive’
How to automate saving the active configuration on an interval:
Let’s say you are making a copy of your JUNOS archive every Tuesday
by logging in and making the copy. Wouldn't it be easier if JUNOS
could do this for you, not just on Tuesdays but every day? You can
configure JUNOS to automatically save the latest active configuration
file and transfer it to a remote host.
1. If you have set up an archive host, or set of hosts, use these
commands to specify a URL for each host that tells JUNOS where to
send the configuration:
set system archival configuration archive-sites ftp://jadmin:
password@remot/archives
2. Now, configure in seconds how often (in seconds) you want JUNOS
to save the active configuration. You can specify any interval from 15
minutes (900 seconds) up to 48 hours (2880 seconds).
set system archival configuration transfer interval 1440
This configures JUNOS to take the active configuration and send a
copy to the ftp remot server in the directory archives every 1440
seconds (every 24 hours, once per day).
How to automate saving the active configuration upon commit:
Another option is to configure JUNOS to archive the active configura-
tion after every commit (i.e. every time the configuration has been
changed):
1. Set up the location to send the saved active configuration file:
set system archival configuration archive-sites ftp://jadmin:
password@remo/archives
2. Configure JUNOS so that it transfers the active configuration after
every commit:

set system archival configuration transfer-on-commit
Now when anyone commits a change on the device, a copy of the latest
active configuration is transferred to the remote archive host for safekeep-
ing.
Loading Configurations
You can use the load command to insert saved configuration files into the
candidate. You can load a complete or partial configuration from a local
file, a file on a remote machine, or from a terminal emulator’s capture
window. A variety of options let you manage exactly how JUNOS
integrates the loaded file into your candidate.
Load override
Use the load override command to completely replace the current
candidate configuration with a previously stored file. You must enter the
load override command from the top of the configuration mode.
This example loads the router-config file saved in the previous section
to the /var/tmp directory on the device, completely overwriting the
existing configuration:
jadmin@juniper1# load override /var/tmp/router-config
load complete
[edit]
jadmin@juniper1# commit
commit complete
ALERT! Remember that any newly loaded configuration file only replaces the
candidate configuration. You must enter a commit command for it to
become the active running file.
Load merge
Instead of replacing a configuration, you may want to add a configuration
snippet to a device. For example, you can use the load merge command to
add the system login configuration statements saved previously in the
local directory of the device:
[edit]
jadmin@juniper1# load merge system-login
load complete
This example loads the system-login file on the device, and merges it with
the candidate configuration file from the top of the configuration tree.
You must always enter the load merge command from the top of the
configuration mode. JUNOS adds these statements, as you saved them, to
the [edit system login] hierarchy location of your configuration.

NOTE The save command always captures the hierarchy reference from the
root of the configuration, so the load merge command always adds the
statements exactly in the same place as you saved them. There may be
times when you want to add saved statements to a different part of
your configuration. The relative option discussed below lets you
specify where JUNOS loads the configuration statements of a saved file
Load merge terminal
Let’s suppose that you want to copy the syslog settings that have
already been configured on one JUNOS device, and paste them onto
another:
system {
syslog {
user * {
any emergency;
}
host 172.26.27.8 {
any notice;
authorization info;
interactive-commands info;
}
file messages {
any notice;
authorization info;
}
}
}
First copy the snippet from the source, using a copy command such as
Control+C. Then enter the load merge terminal command on the
destination router, and paste the snippet in, for example, by using the
paste command, Control+V:
[edit]
jadmin@juniper1# load merge terminal
[Type ^D at a new line to end input]
system {
syslog {
user * {
any emergency;
}
host 172.26.27.8 {
any notice;
authorization info;
}
file messages {
any notice;

authorization info;
}
}
}
^D
load complete
ALERT! When using a terminal command, make sure you end the terminal with
Control+D (^D).
The new syslog statements are now ready to be applied to your
configuration:
jadmin@juniper1# commit
Load merge terminal relative
Perhaps you want to merge a configuration snippet part way down
inside a branch of the JUNOS configuration tree. If so, you can append
the relative keyword to the load merge command.
Let’s say that you want to copy just the syslog host from the previous
example. Copy the host details using a copy command such as
Control+C, making sure you include the end curly bracket.
On the destination device, navigate to the desired section of the
JUNOS configuration:
jadmin@juniper1# edit system syslog
[edit system syslog]
jadmin@juniper1#
Then issue the load command as before but with the addition of the
relative keyword:
jadmin@juniper1# load merge terminal relative
[Type ^D at a new line to end input]
host 172.26.27.8 {
any notice;
authorization info;
}
^D
load complete
[edit system syslog]
TIP You can also use the relative option when loading a snippet of a
configuration from a file. The format of the command is similar in
form to the above example: load merge filename relative. (Find
additional examples of how you can use load commands in the CLI
User Guide available at www.juniper.net/techpubs.)

What to Do Next &Where to Go ...
www.juniper.net/dayone
If you’re reading a print version of this booklet, go here to download
the PDF version which includes supplemental info in its Appendix.
Also, find out what other Day One booklets are currently available.
www.juniper.net/junos
Everything you need for JUNOS adoption and education.
http://forums.juniper.net/jnet
The Juniper-sponsored J-Net Communities forum is dedicated to
sharing information, best practices, and questions about Juniper
products, technologies, and solutions. Register to participate in this
free forum.
www.juniper.net/techpubs
All Juniper-developed product documentation is freely accessible at
this site. Find what you need to know about JUNOS Software under
each product line.
www.juniper.net/books
Juniper works with multiple book publishers to author and publish
technical books on topics essential to network administrators. Check
out this ever-expanding list of newly published books.
www.juniper.net/training/fasttrack
Take courses online, on location, or at one of the partner training
centers around the world. The Juniper Network Technical Certifica-
tion Program (JNTCP) allows you to earn certifications by demon-
strating competence in configuration and troubleshooting of Juniper
products. If you want the fast track to earning your certifications in
enterprise routing, switching, or security use the available online
courses, student guides, and lab guides.

Appendix
Configuration InformationWorksheet . . . . . . . . . . . . . . . .74
JUNOS Basics Configuration . . . . . . . . . . . . . . . . . . . . .76
Command References . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Note: ThisAppendix only appears in the PDF edition of
Day One:Configuring JUNOS Basics.

Conﬁguration InformationWorksheet
Hostname
Management Port IP Address
Management Port Network Preﬁx
Loopback Interface IP Address
Backup Router IP Address
Domain Name Server IP Address(es)
NetworkTime Protocol Server IP Address
Initial Root Password
You should keep all your
passwords secret at all times.
If you write down a password
here,make sure that this
document is kept safe and
secure.

Appendix 75
Local Username
Initial Local Password
Method of Remote AuthenticationYou Use
IP Address(es) ofYour Remote Authentication Server(s)
Server Authentication Password
IP Address of Interface(s)
IP Address of a Network Management System
SNMP Community
IP Address of a Log Host
The device may need a secret
key for encryption to access
the authentication server.

Day One:Configuring JUNOS Basics Configuration Listing
This section provides the configuration listing for all the statements
that this booklet has helped you to configure on your device. The
listing provided on the following pages is the resulting configuration if
you entered all the commands that are designated by an arrow (in the
left margin) exactly as they are shown. These commands are found in
Chapters 2 through 5 of this booklet.
The resulting configuration listing on your device may also have
additional statements associated with previously defined default or
preconfigured settings. If you chose to set up your device with the
custom settings specific to your network, then your output will include
those specific configuration names, addresses, etc.
## Last commit: 2009-06-16 08:32:35 CEST by root
version “9.5I0 [builder]”;
groups {
common {
snmp {
community public {
authorization read-only;
clients {
192.168.1.0/24;
0.0.0.0/0 restrict;
}
}
community private {
authorization read-write;
clients {
192.168.1.15/24;
0.0.0.0/0 restrict;
}
}
trap-options {
source-address lo0;
}
trap-group managers {
version v2;
categories {
authentication;
}
targets {
192.168.1.15;
}
}
}
}

Appendix 77
}
apply-groups common;
system {
host-name juniper1;
domain-name enterprise.com;
domain-search [ enterprise.com department.enterprise.com ];
backup-router 172.26.31.1 destination [ 172.26.31.1/32
172.16.0.0/12 ];
time-zone Europe/Amsterdam;
authentication-order [ radius tacplus password ];
name-server {
172.26.27.2;
172.26.27.3;
}
radius-server {
172.26.27.5 {
port 1845;
secret "$9$8.wx-b4aU.PQZG39pu1INdb";
}
}
tacplus-server {
172.26.27.6 {
port 49;
secret "$9$KyEWXNs2aikP4oT39Cu0LxN";
}
}
login {
announcement «Maintenance scheduled 11PM to 2AM tonight»;
message "Welcome n to n JUNOSn";
user jadmin {
full-name “Juniper Network Administrator”;
uid 1250;
class super-user;
authentication {
encrypted-password “$1$jetUXT44$D9KVQKofqwKMEfcBjp
3zg0”;
}
}
user remote {
uid 2001;
class super-user;
}
user adminjlk {
uid 2002;
class super-user;
}
}
services {
ssh;
web-management {

http;
}
}
syslog {
user * {
any emergency;
}
user jadmin {
any critical;
}
host loghost {
any notice;
facility-override local7;
log-prefix JUNOS;
}
host set {
explicit-priority;
}
file all_messages {
any warning;
authorization notice;
}
console {
any error;
}
time-format;
}
ntp {
boot-server 172.26.27.4;
server 172.26.27.4;
}
}
interfaces {
ge-0/0/1 {
unit 0 {
family inet {
address 192.168.100.1/30;
}
}
}
me0 {
unit 0 {
family inet {
address 172.26.27.44/24;
}
}
}
lo0 {
unit 0 {
family inet {
address 192.26.0.110 {

Appendix 79
preferred;
}
address 127.0.0.1/32;
}
}
}
}
snmp {
description "Juniper EX4200";
location "London Corporate Office";
contact "For help, please email support@enterprise.com";
view ping-mib-view {
oid 1.3.6.1.2.1.80 include;
oid jnxPingMIB include;
}
community ping-mib {
view ping-mib-view;
authorization read-write;
}
community managers;
rmon;
health-monitor {
interval 900;
rising-threshold 70;
falling-threshold 60;
}
}

Command Reference
(Summary of commands from Day One: Using the JUNOS CLI.)
Configuration Mode Commands
activate Activate a portion of the configuration.
annotate Leave comments about a configuration
statement.
commit Commit candidate set of changes.
commit at Commit candidate at a set time.
commit check Validate the candidate configuration
without activating any changes.
commit confirmed Automates rollback if the user does
not follow the command with a confirmation.
compare Display the differences between the two
configurations.
copy Copy a statement.
deactivate Mark portions of the configuration as
inactive.
delete Remove a configuration statement(s) or
identifier.
edit Move to the designated hierarchy level.
exit Exit this level of the configuration hierarchy. At
the top level, exit configuration mode.
exit configuration-mode Exit configuration mode.
help Get onboard help.
pipe Take output from one command and use it as
input to another command or redirect the output to a
file.
rename Assign a new name to a configuration or
identifier.
rollback Restore the candidate file to a previous
committed configuration.
run Run an operational mode command.
set Create a statement hierarchy and set identifier
values.
show Display the candidate configuration.
top Move to the first hierarchy level.
up Move up one level in the hierarchy.
Operational Mode Commands
clear Remove system information.
configure Enter configuration mode.
configure exclusive Get an exclusive lock on the
candidate so others can’t edit it.
configure private Give the user their own copy of the
candidate configuration.
exit Exit operational mode.
file copy Create and archive files.
file list Lists files and directories on the device.
file show View the file contents.
monitor Show real-time debugging info.
ping Send a message to another host to verify
connectivity.
file.
request Install new software versions, reboot, shut
down.
restart Restart individual operating system daemons.
set Establish system properties.
show Show system information.
ssh Start secure shell on another host.
start shell Log in to the C shell interface.
telnet Opens a terminal connection to another device
or host on the network.
traceroute Record and display every IP packet hop
from one location to another.

Appendix 81
Command Reference
(Summary of commands from this Day One booklet.)
commit Commit candidate set of changes.
commit synchronize Commit candidate set of changes
to both routing engines of a single device.
commit comment Add a comment that describes the
committed configuration.
commit confirmed Automates rollback if the user does
not follow the command with a confirmation.
commit and-quit Save software configuration changes,
activate the configuration, and exit configuration
mode.
compare Display the differences between the two
configurations.
copy Copy a statement.
edit Move to the designated hierarchy level.
exit Exit this level of the configuration hierarchy. At
insert Insert a new ordered data element
load merge Combine the current configuration and the
loaded configuration.
load override Replace the current configuration with
the loaded configuration.
file.
rename Assign a new name to a configuration or
identifier.
quit Exit this level of the configuration hierarchy. At
replace Replace character string in configuration.
rollback Go back to the previous committed
configuration.
run Run an operational mode command.
save Save configuration to ASCII file.
set Create a statement hierarchy and set identifier
values.
set apply-groups Apply a configuration group to a
specific hierarchy level in a configuration.
set groups Create a configuration group.
set interfaces Interfaces on this device.
set snmp SNMP configurations on this device
set system Create a statement hierarchy and set
identifier values in the system branch of the
configuration.
> authentication-order Order in which authentication
methods are invoked.
Operational Mode Commands
clear Remove system information.
configure Enter configuration mode.
configure exclusive Get an exclusive lock on the
candidate so others can’t edit it.
configure private Give the user their own copy of the
candidate configuration.
exit Exit operational mode.
file copy Create and archive files.
file list Lists files and directories on the device.
file show View the file contents.
monitor Show real-time debugging information.
ping Send a message to another host to verify
connectivity.

Command Reference
(continued from previous page)
ﬁle.
request Install new software versions, reboot, shut
down.
restart Restart individual operating system daemons.
set Establish system properties.
show Show system information.
ssh Start secure shell on another host.
start shell Log in to the C shell interface.
telnet Opens a terminal connection to another device
or host on the network.
traceroute Record and display every IP packet hop
from one location to another.

Configuring junos basics

More Related Content

Viewers also liked (20)

Similar to Configuring junos basics (20)

Recently uploaded (20)

Configuring junos basics