Cpx eng manual

eeee uuuu rrrr öööö ssss eeee cccc CCCC PPPP XXXX
CCCC oooo nnnn tttt rrrr oooo llll PPPP aaaa nnnn eeee llll
Engineer’s
Reference Guide
cpx 020.qxd 09/08/2006 16:31 Page 1

CPX Engineer’s Reference Guide
Page 1
CONTENTS
IMPORTANT ...........................................................2
1 Introduction............................................................3
2 System Installation - Wiring..................................4
3 Resetting Factory Defaults ...................................12
4 Programming .........................................................14
Moving Around ...............................................14
Headers & Options ........................................14
Common Options with Menu Numbers ..........17
Programming Zones ......................................18
Reporting a Mains Fail on a PSU ...................30
Programming Setting Modes .........................31
Programming Entry Times .............................38
Programming Bells / Sounders ......................40
Programming Keypad ....................................44
Programming Digicom / Vo-Comm Off/On .....48
Programming Linefault Modes ......................58
Programming Panic ......................................60
Programming PGM2 / PGM3 / Timers............62
Programming Reset Modes ...........................66
Programming Sounder Levels .......................68
Programming PGM 1 / Timers .......................70
Programming Engineer Code ........................72
Programming Service ....................................73
Programming Custom Screens .....................75
Programming Diagnostics / Log ....................76
Programming Alarm Confirm (Notes) .............80
Programming Alarm Confirm (Scenarios) ......82
Programming Alarm Confirm .........................84
NovActive Description & Programming ..........89
Programming Point ID & SIA Protocols..........91
Linefault Sounders Description ......................93
Engineer Reset...............................................94
Wiring Proximity ‘E’ & ‘I’ Readers...................95
Clearing ‘Test Fail’ Indication .........................96
5 Specifications ........................................................97
Power Supply Rating......................................98
6 4 Wire Contour RKP Wiring Information..............100
cpx 020.qxd 09/08/2006 16:31 Page 1

IMPORIMPORTTANT!ANT!
Input: AC230V +/-10% ~50Hz 125mA Max. 35W Max
Nominal Temp Range: 0 - 50°
eurösec Plastic Versions
For Indoor Use Only
This equipment is intended only for use as a Security Alarm Control Panel. Adequate
ventilation away from heat and humidity must be provided. The unit must be fixed
securely to a non-flammable surface using suitable fixings.
All mains wiring must conform to the relevant current IEEE wiring regulations (or
appropriate international regulatory standards). See Mains Supply Connection section
within this manual for more detailed instructions.
All wiring must be protected from sharp or jagged edges.
All low voltage (alarm) wiring must be to the appropriate international regulatory
standards and comply to good wiring practice and should be routed away from the
mains cables.
Replacement fuses should be of the same type and rating conforming to IEC 127.
The maximum current draw from the unit for all output combinations must not exceed
1A. Please see note: *Power Supply Rating in Specifications chapter.
The unit is intended for use with a suitable re-chargeable lead acid battery
permanently connected to the appropriate terminals.
All documentation and manuals must be thoroughly read by suitably qualified
installation personnel prior to installation.
The unit has no user serviceable parts inside. Internal access should only be by suit-
ably qualified personnel.
Provision is provided for an earth connection within the mains input connector block,
this connection is for protection of the wiring only and is not functional for the unit.
Battery Fuse
An in-line Battery Fuse has now been incorporated into this product. The fuse rating
is 2 Amp Anti-Surge. The fuse holder is spring loaded, therefore you should ensure
that the battery lead is not under tension in order to maintain a good connection
between the fuse and the holder.To change the fuse push the two halves of the hold-
er together and twist anti-clockwise. Please ensure correct battery charge on comple-
tion of the installation and during each service visit.
Page 2
cpx 020.qxd 09/08/2006 16:31 Page 2

1 INTRODUCTION
The eurösec CPX Control Panel is a microprocessor based unit that has been
designed to be suitable for all types of domestic and commercial installations. All zones
are fully programmable by the engineer.
On power up / reset, the Control Panel can be set to the old BS or EN2 (Grade 2)
operating standards. It is ESSENTIAL that a 4 6 YES NO reset is done to all new
systems before commencement of programming.
Upon completion of the installation the engineer may, if required, re-program several
factory set options so as to tailor the Control Panel to suit the requirements of the sys-
tem.
The CPX control panel uses 32 character LCD Remote Keypads for control of the
system via User Code(s) and programming of the system via an Engineer Code. The
Factory Default Codes are
Default Master User Code 5678
Default Engineer Code 1234
The Engineer code may be ‘Locked’ into the system during engineer
programming and it should be noted that if the ‘Locked’ code is not known the
only way to have it returned to the factory default is to return the PCB to the
factory.
Option Formats. When an option cannot be changed the display will show a : rather
than the usual = sign. Pressing the No key is disregarded and the panel will react as
though the Yes key has been pressed (i.e. it will move onto the next option).
cpx 020.qxd 09/08/2006 16:31 Page 3

2 SYSTEM INSTALLATION - WIRING
Planning the Control Panel Location
Consideration in locating the fixing position of the Control Panel should be given to:
Access for the routing of cables for the system from detection devices,
sounders (internal and external), remote keypads, mains, etc.
The position of the underside retaining screw.
The fixing of a 3 amp fused spur with disconnection facility.
When fitting the RKP(s) consideration should be given to:
Operation of the keypad.
Readability of the display.
The Panel should be fixed to the wall using appropriate wall plugs and No.8 screws at
least 30mm long. Do not tighten the screws at this stage, wait until all your wiring is in
place.
Wiring Considerations
With the exception of the mains wiring all interconnections should be made with
multicore 7/.02 alarm cable.
Good wiring practice should be observed throughout the installation and the following
tips may prove useful.
Never run alarm cables parallel to mains cables, telephone cables or any
other cables that may be carrying inductive loads
Whenever you have to cross mains cables with alarm cables ensure that you
do so at 90°
Whenever possible wire the mains connection for the control panel back to
the consumer unit via a 3A fused spur with disconnection facility.
Never tap into ring main circuits that have fridges/freezers on them.
Never tap into lighting circuits that have fluorescent lighting units on them.
Page 4
cpx 020.qxd 09/08/2006 16:31 Page 4

Mains Wiring
A 230V a.c supply should be taken directly from the consumer unit. In order to comply
with the relevant current wiring regulations this should be via a 3 Amp fused spur with
disconnection facility.
Page 5
Consumer Unit
3A Unswitched
Fused Spur Control Panel Mains
Terminal Block
Mains
Connection Colours
Live = Brown (Red)
Neutral = Blue (Black)
Earth = Copper
Yellow/Green sleeving should be
used for Copper Earth Conductor
cpx 020.qxd 09/08/2006 16:31 Page 5

Wiring Diagrams - CPX PCB
Page 6
-+-
STROBEBELL
BELLSABPGM1SPR+SPR+-+-+-+-+-+-+-+-+-+-AONAINAOUT
HOLDTMPRAUX12VTZAZ1AZ2AZ3AZ4AZ5AZ6AZ7AZ8
RS485REMOTEKEYPADPGM2
REDBLKYELGRND2D10V12V
BATTAC
-+
PSTN OUT LINE IN
C3 B2 A5 B2 A5
F1BATTERY20mm
2AANTI-SURGE
F2AUX20mm
1AQUICKBLOW
F3KEYPAD20mm
250mAQUICKBLOW
PATCH
LEAD
CONNECTION
TELEPHONE CONNECTIONS
KEYPAD
CONNECTIONS
RS485(RADIOEXPANDER)
CONNECTIONS
EXTERNALSOUNDER
/STROBEMODULE
INTERNALSPEAKERS
MIN16OHM
REMOTE
KEYPAD(S)
MAYBEWIRED
INSTAROR
DAISYCHAIN
FORMAT
D2/BD1/A0V12V
D2/BD1/A0V12V
LINE
IN
3
2
5
OTHER
SOCKETS
ONPREMISES
Note:Onlyreplacefuses
withcorrecttype&value
GTAG
PROXIMITY
READER(S)
Note:680Ohm
resistorshould
befittedtoONE
oftheRKPs.If
RKPsarewired
indaisychain
thisshouldbe
thelastRKPin
theline,
Strobe - Trigger
Bell / Strobe + Hold-Off
Bell - Trigger
Bell Hold-Off - Supply
- Tamper Return
DefaultEngineerCode
1234.
DefaultUser
5678.
ToDefaultPanel
PowerUp.
WhilstversionNo.
isdisplayedenter
46YesNo.
ThiswillnotDefault
theEngineerCode
ifithasbeenlocked.
Connectionsavailableare
modeldependant
680Ohm
cpx 020.qxd 09/08/2006 16:31 Page 6

Remote Keypads
Up to four remote keypads may be fitted to the eurösec CPX control panel. Each
Keypad offers a 32 character backlit LCD.
A four core connection will be required between the control panel and remote
keypad(s), keypads may be in a 'daisy chain' or ‘star’ format.
Note: 680 Ohm resistor must be fitted to ONE RKP. If the RKPs are wired
in daisy chain format this should be the last RKP in the line.
Note: Each keypad must be programmed onto the system in order for it to
be recognised by the system.
Note: Depending on the variant of keypad fitted external G-Tag Proximity
Reader(s) may be fitted to each Remote Keypad.
Note: Please refer to the back of this manual if the Control Panel has been
supplied with a 4 Wire Contour RKP (with added zones) for wiring
information.
Page 7
- + -
STROBE BELL
RS485REMOTEKEYPADPGM2
REDBLKYELGRND2D10V12V
BATT AC
- +
KEYPAD
CONNECTIONS
CONNECTIONS
REMOTE
KEYPAD(S)
MAY BE WIRED
IN STAR OR
DAISYCHAIN
FORMAT
D2/BD1/A0V12V
D2/B D1/A 0V 12V
GTAG
PROXIMITY
READER(S)
Note: 680 Ohm
resistor should
be fitted to ONE
of the RKPs. If
RKPs are wired
in daisy chain
this should be
the last RKP in
the line,
680 Ohm
cpx 020.qxd 09/08/2006 16:31 Page 7

Control Panel Output Connections
Digi Modem
The eurösec CPX control panels feature an onboard Digi modem. The Digi provides all
the features of an eight channel communicator whilst the Modem provides facilities for
Gardtec Remote Upload/Download software package.
Telephone Connections
Page 8
- + -
STROBE BELL
BELL SAB PGM1 SPR+ SPR + -
HOLD TMPR AUX 12V
S
EXTERNAL SOUNDER
/ STROBE MODULE
INTERNAL SPEAKERS
MIN 16 OHM
Strobe-Trigger
Bell/Strobe+Hold-Off
Bell-Trigger
BellHold-Off-Supply
-TamperReturn
A5
IN
B2
IN
C3B2A5
Terminal 5
(on existing BT Master socket)
Terminal 2
Terminal 3
Terminal 5
(on other extension sockets)
Terminal 2
Terminal 3
Serial
Telephone
Connection
(Depending on model)
A5
IN
B2
IN
C3B2A5
Terminal 5
(on existing BT socket)
OR
Terminal A
(on BT Terminal Block)
Terminal 2
(on existing BT socket)
OR
Terminal B
(on BT Terminal Block)
Standard
Telephone
Connection
cpx 020.qxd 09/08/2006 16:31 Page 8

Typical Novagard 2G/2G Connections
Control Panel Input (Zone Connection)
Page 9
+12V
0V
S-
ST-
R TMP
F TMP
BELL+
BELL-
SAB TMP
BELLHOLD-
STROBE-
NovaGard 2G/4G
(Strobe terminals omitted)
CPX Control Panel
AZ1
+-
AZ2
+-
AZ3
+-
AZ4
+-
AZ5
+-
AZ6
+-
AZ7
+-
AZ8
+-
N/C Devices
N/C Devices
N/C Devices
N/C Devices
N/C Devices
N/C Devices
6k86k86k86k86k86k86k8
6k8
N/C Devices
N/C Devices6k86k8
4k7
4k7
4k7
4k7
4k7
4k7
4k7
4k7
TZ
+-
6k8
Tamper Zone
becomes Zone 9
ONLY when 9 (EOL)
is selected
4k7
N/C Devices
End of Line Zone Wiring
Multiple units can only be used with BS Standard.
If using EN2, one unit per zone.
AZ1
+-
AZ2
+-
AZ3
+-
AZ4
+-
AZ5
+-
AZ6
+-
AZ7
+-
AZ8
+-
TZ
+-
N/O Devices (PA etc)
connect across Tamper & Zone
N/C Devices
multiple devices are in series
N/C Devices
N/C Devices
N/C Devices
N/C Devices
N/C Devices
N/C Devices
Standard (2 Wire) Zone Wiring
Please see following page for further wiring modes
where Anti-Mask detectors are used
cpx 020.qxd 09/08/2006 16:31 Page 9

Typical Wiring Modes
More Zone Wiring Methods
Page 10
Where Anti-Mask detectors are used, one of the following wiring
modes may be used.
ELF1 wiring is used for detectors that have a
relay output (a pair of terminals) for Fault or
Mask.
The installer should check what output type
the detectors are, noting that all the dectectors
should be of the same type with regards to the
Fault / Mask output.
Typical ELF1 Typical ELF2
ELF2 wiring is used for detectors that
have a transistor output (a single terminal)
for Fault or Mask.
Note: For ELF2 wiring format the 12K
resistor must be linked to the positive
side of the zone terminals.
12K4K76K8
AZx
Alarm Tamper Fault/Mask
+ AZx -
12K
4K76K8
Alarm Tamper
Fault/
Mask
Zone Doubling: Detector on Zone 1 will be Zone 1 and the
Doubled Zone will be Zone 9, Zone 2 will be Zone 2 and the Doubled
Zone will be Zone 10. E.g Zone number + 8 = Zone number for
Doubled Zone. The Zone triggered will be identified through the
resistor value by the system.
Zone Wiring (2 Wire)
TZ (Tamper) AZ (Alarm)
N/C Tamper
Contact
N/C Alarm
Contact
Zone Wiring (EOL)
AZ (Alarm)
N/C Tamper
Contact
N/C Alarm
Contact
4K7 6K8
Zone Doubling (8+8)
AZ (Alarm)
16K 27K 6K8
+ AZx -
Alarm N/C Tamper N/C
1st Detector
2nd Detector
cpx 020.qxd 09/08/2006 16:31 Page 10

Radio Zone Expander
One GardTec Radio Zone Expander may be fitted directly to the RS485 Bus connec-
tions on the control panel PCB without the need for any interface card. A Radio
Expander card will allow eight wireless zones & eight wireless Fobs.
Radio Zone Programming
When programming Radio Zones the zone numbering for the Radio Zones will start at
91. When programming Radio Fobs the numbering of the Fobs will start at 81.
Resistor Colour Codes
Page 11
CONNECTIONS
RS485
REDBLKYELGRN
GRNYELBLKRED
RADIORECEIVER
KEY
ID
ZONE
ID
RECEIVER
DIP SWITCH
SETTINGS
1 2 3 4
ON
1 2 3 4
ON
RADIO EXPANDER WIRING & SWITCH SETTINGS
Blue
Grey
Red
Brown
6K8
Brown
Blue
Orange
Brown
16K
Red
Violet
Orange
Brown
27K
Yellow
Violet
Red
Brown
4K7
Brown
Red
Orange
Brown
12K
cpx 020.qxd 09/08/2006 16:31 Page 11

3 RESETTING FACTORY DEFAULTS
Several reset to factory default routines are available to the engineer at system power-
up but it should be noted that none of these routines will ‘Un-Lock’ a ‘ Locked’
Engineer Code.
The following default routines are available.
a) Pressing 1, 9, YES, NO during initial power up will revert the Master Code
and Engineer Code (not locked engineer code) back to factory defaults.
b) Pressing 3, 7, YES, NO during initial power up will revert all system settings
back to defaults with the exception of the User Names and Zone Descriptors.
c) Pressing 4, 6, YES, NO during initial power up will revert all system settings
back to factory defaults. It is ESSENTIAL that a 4 6 YES NO reset is done
to all new systems before commencement of programming.
d) Pressing 5, 5, YES, NO during initial power up will revert all system settings to
factory defaults and will also set the comms options up for GardTec Remote.
ie Modem On; No Return. For commissioning systems for use with
GardTec Remote use this option.
cpx 020.qxd 09/08/2006 16:31 Page 12

Reset of the factory defaults and entering Engineer Mode:-
Note: It is ESSENTIAL that a 4 6 YES NO reset is done to all new systems
before commencement of programming.
1) Remove all power from the system for at least ten seconds
2) Apply mains power to the control panel.
The display will show, for example:-
(Display will differ dependant on panel version)
3) Whilst this display is showing (the first five
seconds) press the keys shown in a, b, c or d
for the reset required. (E.g. 4 6 Yes No).
The display will show:-
This may show for several minutes.
4) The display will then show:-
Selecting 1:BS - Panel may be programmed to comply with the old BS4737
Standards. DD243 requirements will still apply.
Selecting 2:EN2 - Panel may be programmed to comply with EN50131-1 for
Grade 2 Systems. DD243 requirements will still apply.
5) Select 2:EN2.The display will then show:-
This may show for several minutes.
The display will then show:-
6) Enter Engineer code.
(1234 default). The display will show:-
7) Enter the Authorisor code. The Authorisor code is
the Master User, (default 5678).
Note: It may be required that an engineer has to be authorised by a user
before access to the engineer mode is granted.
8) Press Yes. The display will show:-
Eurosec CPX xx-xx
Please Wait
Select Standard
1:BS 2:EN2
Enter Authorisor
Code . . . . . .
Please Wait
Do you want to . .
Use ENGNR. Mode ?
Program Zones . . . . - - -
Zones ?
Note: This document assumes that 2:EN2 has been selected.
01 Jan 00:01:50
cpx 020.qxd 09/08/2006 16:31 Page 13

4 PROGRAMMING
Moving Around
Enter Engineer mode as described on page 13.
Whenever three underscores are shown on the display the screen is a header.
Pressing the NO key will move to the next header.
Pressing the YES key whilst viewing a header will enter into the options under that
header.
Pressing 0 will escape back one step (except when a numeric entry is required).
You are able to jump to various common options when programming by entering the
relevant menu numbers. With a Header showing, key in the appropriate menu
number, then press Yes. (See Page 17 for Common Options with Menu Numbers).
Below is given a complete list of headers (Shown in Bold Underline) and options that
appear under each header.
Program . . . . _ _ _
Zones ?
Headers & Options
Program Zones
Zone Types
Zone Descriptors
Zone Wiring
Zone Attributes (Test/Part/Chime)
Zone Double Knock/Arm/Log
Zone E/E Mode
Event Tags
Setting Modes
Setting For Full Sets
Setting For Part 1 Sets
Setting Delay
Setting Sounders
Setting Conformation
Auto Part Set
Headers & Options
Entry Times
Entry Time 1
Entry Time 2
Bells / Sounders
Bell Type
Bell Delay/No Arms
Bell & Sounder Ring
Bell Tamper Mode
Bell For Part Set
Keypad / Keyswitch
Keypad Alert 1 Keys
Keypad Alert 2 Keys
Quick Key
Number of Keypads
Keypad Backlight Mode
Ace / Prox
cpx 020.qxd 09/08/2006 16:31 Page 14

Headers & Options
Digicom
Type or Test
Vo-Comm
Start Delay
Channels
Digicom/Modem Functions
Line Fault Modes
Line Fault Sounders
Line Fault Mode in Exit
Line Fault Log Mode
Line Fault Detect Time
Panic / Duress
PA Mode
Testable / Non-Testable
Duress Off (To conform with EN standards,
Duress is defaulted to Off and cannot be changed)
PGM2 / PGM3 / Timers
PGM 2 Mode
PGM3 Mode
Timer 1 On Time
Timer 1 Off Time
Reset Modes
Mains Fail Delay
Alarm Reset
Tamper Reset
Alarm Restore On/Off
Abort Time
Headers & Options
Sounder Levels
Chime Level
Entry/Exit Level
Key Beep Level
PGM1/Custom
PGM1 O/P
Custom Output 1
Custom Output 2
Custom Output 3
Custom Output 4
Custom Output 5
Custom Output 6
Custom Output 7
Custom Output 8
Engineer Code
Engineer Code
Engineer Code Locked/Unlocked
cpx 020.qxd 09/08/2006 16:31 Page 15

In conclusion, the Yes and No Keys are used to navigate. The No Key is also used to
change a value (may also require a numeric input) and the Zero Key is used to move
back a level (not when display is expecting a numeric input)
If you are confident in programming the CPX Control Panel please use the headers
and options above to continue
Otherwise
Please continue with the next section for a Step by Step Guide to programming the
CPX Control Panel.
Only the major options will be covered in the Step by Step sections. After
completing the sections you should be confident to program the remaining
options.
Headers & Options
Service
Service Timer / PTM
Time To Next Service
Service Tel No.
Lock-Out On/Off
Engineer Mode Constant/Timed
Custom Screens
LCD Status Display
LED Status Display
Diagnostics / Log
List Event Log
Change List Diagnostics
Headers & Options
Alarm Confirm
Window Time
On Entry
Sounder Mode
Reset Mode
Secondary Time
ET Mode
Bell Mode
Strobe Mode
Start Delay
Comms Restore
Keypad Opening
cpx 020.qxd 09/08/2006 16:31 Page 16

Common Options with Menu Numbers
You are able to jump to various common options when programming by entering the
relevant menu numbers. With a Header showing, key in the appropriate menu number,
then press Yes.
Page 17
Menu Jumps to
1 PGM 1 Output
2 Timer 1 On Time
4 Timer 1 Off Time
6 PA Mode
8 Chime Level
9 Entry Exit Level
10 Exit Sounder Mode
11 Final Set Delay
12 Full Set Setting Time / Setting Mode
13 Part 1 Set Setting Time / Setting Mode
20 Alert 1 Keys Mode / On Off
21 Alert 2 Keys Mode / On Off
22 Install Keypads
23 Bell Delay / No. of Bell Arms
24 Bell Ring Time / Sounder Mode
26 NovActive On Off
27 Bell Tamper Ring On Off
28 Entry Time 1
29 Entry Time 2 / Warning Bell
30 Fire Zone Delay
34 Digicom Type
35 Key Beep Level
37 Zone Re-Arm / Double Knock Time
38 Engineer Code
40 Line Fault Sounders
41 Line Fault Mode
42 Line Fault Log
44 PGM 1 Output
46 Main Fail Delay
47 Tamper Reset Mode
48 Backlight Mode
50 Zone Response
51 Zone Types
52 Test Zone (Attributes)
53 Save Panel NVM to PTM / Service Timer
54 Service Due Weeks
55 Zone Log Limit
58 Digicom Channels
64 Alarm Restore / Abort Time
65 Test Digicom Channels
66 E/E Zones in Part Set
67 Engineer Code Locked / Unlocked
68 Strobe Confirm
Menu Jumps to
69 Auto Part Set
70 Part Set Bells
71 Zone Types ( Enter Zones)
72 On Board Pairing
75 Program Zone Wiring
92 LCD Status
97 List Event Log
131 NovActive
139 PSU Test Time
153 Test Zones
155 Confirm Time Window (DD243 Section)
156 Secondary Time Window
157 Confirm on Entry On Off
158 Sounder Trigger
159 Unconfirm Reset Mode
160 E/T Mode
161 Bell Trigger
162 Confirm Start Delay
164 Strobe Timer
165 Strobe Trigger
166 Custom 1 OP Mode
174 Comms Restore On Off
cpx 020.qxd 09/08/2006 16:31 Page 17

Programming Zones
1) With the display showing:-
2) Enter the Engineer code (1234 default)
3) Enter the Authorisor code. The Authorisor code is
the Master User, (default 5678).
4) Press YES. The display will show:-
This is Engineer Mode.
7) Enter the zone number you wish to program
e.g 1 followed by Yes. The display will show,
for example:-
8) Press No. The display will show:-
9) Note the chevron has now appeared before
the Zone Type. Now press the No key until the
Zone Type you require is displayed.
01 Jan 00: 00: 01
Program . . . . _ _ _
Zones ?
Program Zone
Types ?
Enter Zone # _ _ _
001 = Ent/Ex
= Remove -
001 > Ent/Ex
= Remove -
Enter Authorisor
Code . . . . . .
Do you want to . .
Use ENGNR. Mode ?
cpx 020.qxd 09/08/2006 16:31 Page 18

Zone Types available are:-
12 Hour
Full Alarm if Control Panel is Set.
Access
Will allow to pass through on exit.
Will allow to pass through on entry only if E/E is opened first.
24 Hour
Internal Sounder if Unset.
Full alarm if Set.
Remains active in Engineer Programming Mode.
Entry/Exit (or E/E)
Zone used as last exit point (will terminate exit time if setting mode is set to
E/E or Time+E/E).
Will start E/E time if opened when Control Panel is Set
Part E/E
As Access if Control Panel is Full Set
As Entry/Exit if Control Panel is Part Set
Panic
24Hour Personal Attack (or Panic Attack). Active if Control Panel is Set,
Unset or in Engineer Programming Mode . May only be tested via Engineer
code if programmed as testable.
Alert
Internal Sounder Only, Recorded to Log when Unset
Recorded to Log when SET
Fire
Will give Fire alarm when activated (pulsed sounders) with Control Panel Set
or Unset.
Remains active in Engineer Programming Mode.
ET
Exit terminator. Used for final setting of the system. Exit Mode must be
programmed for ET.
Monitor
Will write to the log once only in any one set or unset unless chime is
allocated then all activations are written to the log.
KSW Bat
When used, zone should be connected to the trouble/status output of third
party radio equipment that is capable of giving a low battery signal.
Line Fault
When used, acts as a Line Fault input to the control panel.
Fault
When used, will act as an Fault input to the control panel when an internal
fault has been detected within the PIR.
Mask
When used, will act as an input to the control panel if the detector has been
blocked or covered.
Note: Fault and Mask are treated as 24Hr but trigger a Fault Sound in Day (Unset) Mode. The Fault
sound is a three tone sounder.
cpx 020.qxd 09/08/2006 16:31 Page 19

10) When you are satisfied with your selection
press Yes. The display will show for example:-
We will now be changing the Zone Attributes. Options available are:
Remove- The zone may not be Removed (Omitted) by the end user. (Part
Sets are still allowed).
Remove+/DK Zone may be Removed (Omitted) by the end user and is a Double
Knock Zone (2 activations required within time window or zone left
open for 15 seconds).
Remove-/DK Zone may not be Removed by end user (Part Sets are still allowed)
and is Double Knock Zone.
Off Zone is turned Off (Use with caution).
Norm Key Zone is a Keyswitch Zone for a normal type Keyswitch
Bias Key Zone is a Keyswitch Zone for a Bias (momentary) type Keyswitch
Remove+ Zone may be Removed by end user.
11) Press No until the setting you require is
displayed then press Yes.
12) The display will show the next zone to program.
You should repeat from Step 7 until you have
programmed all the zones.
13) When all required Zones have been
programmed press 0 (zero) key twice.
001 = Ent/Ex
> Remove -
Program Zone
Types ?
Program Zone
Descriptors ?
Enter Zone # _ _ _
cpx 020.qxd 09/08/2006 16:31 Page 20

16) Enter the Zone number you wish to
program the Descriptor for followed by Yes.
The display will show for example:-
18) You should now program the Descriptor you
require using the template below for the
key allocation in a similar way that you you would
type a text message on a mobile telephone.
As the desired character is displayed press the
Yes key to move on to the next character.
Continue until the line is complete.
1 2 3
ABC DEF GHI
4 5 6
JKL MNO PQR
7 8 9
STU VWX YZ Space
No 0 Yes
Delete 1234567890 Enter Character
19) As you enter the last character the display
will move on to the next Zone. For example:-
20) Repeat from Step 16 until all the Descriptors
you require have been programmed. Then
press 0 (zero) key twice.
Zone 001 Name =
Zone 001
Zone 001 Name =
Zone 001
Zone 001 Name =
_
Program Zone
Descriptors ?
cpx 020.qxd 09/08/2006 16:31 Page 21

Note: Zone Response time is defaulted to 400ms and may not
be changed.
Note: Zone response time may be programmed as a global
parameter. The default time is 400ms and may be reprogrammed
from 2 to 14 seconds. (increments of 2 seconds).
The time programmed for this option will apply to all zones, there is no option for individual response
times per zone. It is a global setting.
Once the Fault / Mask as been triggered the response time for the Fault / Mask will revert to the
default time of 400ms until the fault / mask problem has cleared.
24) Press No until the required settings you require are
displayed then press Yes. The display will show:-
Wiring Modes available are.
8 (2 Wire) Two wires are used for the zone and a global tamper is used.
9 (EOL) Two wires are used in conjunction with two resistors to give
End Of Line wiring, this is the most secure wiring format.
8+8 (EOL) This wiring method uses double EOL format to give 16 Zones
from the control panel.
Note: For information on how to wire for the various wiring modes please refer
to the wiring section within this manual.
If selecting 9 (EOL) follow steps 24 through to 26. If selecting 8+8 (EOL) jump to step
28.
Press Yes.
26) The display will show:-
Program Zone
Wiring ?
Zone Response
:400 mS
On-Board Zones
=9<EOL>
Fault / Mask Zones
Response=Norm
On-Board Zones
=9<EOL>
On-Board EOL
=Norm
cpx 020.qxd 09/08/2006 16:31 Page 22

Three wiring options are available under 9 (EOL):
Norm: Standard GardTec wiring configuration without Mask or Fault detection.
Note: Does not give any Fault or Masking detection and should only be used with Zone pairing.
ELF1: ELF1 wiring is used for detectors that have a relay output (a pair of terminals)
for Fault or Mask..
ELF2: ELF2 wiring is used for detectors that have a transistor output (a single
terminal) for Fault or Mask.
Note: We would recommend that either ELF1 Format or ELF2 Format (dependant on detector output type,
Relay or Transistor) is used. ELF1 or ELF2 wiring modes will allow for Alarm, Tamper, Fault and Masking to be
monitored from a single zone without the need for zone pairing.
Note: The installer should check what output type the detector are, noting that all the detectors should be of the
same type with regards to the Fault / Mask output.
27) Press No until the setting you require is displayed
then press Yes. The display will show.
If 8+8 EOL wiring option is required.
Press No until 8+8<EOL> is displayed.
Zone Pairing.
A zone is used to monitor Masking and Fault.
This is achieved by selecting Zone Pairing as on. Zone Pairing cannot be used in ELF1 or ELF2
wiring modes.
When using Zone Pairing each zone will have a corresponding paired zone that will be used for
Masking and Fault signals. This is done by using the Odd numbered zones for the normal alarm
detection and the Even numbered zones for Masking and Fault Detection. For example.
Please note that half the zones on the system would be lost for processing the Mask and Fault
signals and it would be more prudent to use the ELF1 or ELF2 modes as described previously.
Radio ZEX
=Off
On-Board Zones
=9<EOL>
On-Board Zones
>8+8<EOL>
On-Board Pairing
=Off
Alarm Zone
Zone 1
Zone 3
Zone 5
Zone 7
etc...
Pared Zone for Mask / Fault
Zone 2
Zone 4
Zone 6
Zone 8
cpx 020.qxd 09/08/2006 16:31 Page 23

30) Press No until the setting you require is displayed.
Then press YES. The display will show:-
32) If you are not using Radio Detectors press Yes
and jump to Step 33
Otherwise
Press No until the display shows:-
Radio ZEX
= Off
Radio ZEX
= On
Radio ZEX
=Off
cpx 020.qxd 09/08/2006 16:31 Page 24

Comprehensive instructions on how to setup and program the Radio Expansion
are given in the document Hybrid Wireless Set-Up & Programming Guide
supplied with the Radio Receiver.
Any 12Hr type zone(s) may be placed on Test. A Zone on Test will never trigger
an alarm or send a central station signal. If the Zone(s) fails the Test when the
system is Set the display will show Test Fail when the user Un-Sets the system.
After 20 successful Sets and Un-Sets the Zone(s) will be taken out of Test by the
system. (To reset a Test Failed display FULLY Set then Unset the system).
37) If you do not wish to put a Zone(s) on Test press
Yes and jump to Step 43
Otherwise
39) Enter the Zone number you wish to place on Test
followed by Yes.
40) To add more Zone(s) to the Test repeat from
Step 38.
Program Radio
Functions ?
Program Zone
Wiring ?
Program Zone
Attributes ?
Test None
Test 003
Enter Zone # _ _ _
then +YES or -NO
cpx 020.qxd 09/08/2006 16:31 Page 25

41) When you have finished adding Zones to Test
press Yes.
Three Part Sets are available on the CPX control panel. Zones added to the PT-1
(Part 1) screen will be Removed (Omitted) when the system is Part 1 Set. Zones
added to the PT-2 (Part 2) screen will be Removed (Omitted) when Part Set 2 is
used. When Part Set 3 is used Parts 1 & 2 are combined and Removed (Omitted).
43) If you do not wish to enter PT-1 Zone press Yes
and jump to Step 47
Otherwise
Press No. The display will show:-
44) Enter the Zone number you require for PT-1
followed by Yes.
45) To add more Zones to PT-1 repeat from Step 43
46) When you have finished adding Zones to PT-1
press Yes
Pt-1 None
Pt-2 None
Pt-1 004
Enter Zone # _ _ _
then +YES or -NO
cpx 020.qxd 09/08/2006 16:31 Page 26

48) If you do not wish to enter PT-2 Zone press Yes
and jump to Step 52
Otherwise
49) Enter the Zone number you require for PT-2
followed by Yes.
50) To add more Zones to PT-2 repeat from Step 47
51) When you have finished adding Zones to PT-2
press Yes
Two Chime suites are available on the CPX control panel so for example you
would have the Front Door on Zone 1 programmed into Ch1 and the Rear Door
on say Zone 6 programmed into Ch2. When the system is Unset opening the
Front Door will produce a Chime. Opening the Rear Door will produce a different
Chime.
It should be noted that Chime must be programmed as On from the user mode.
Please refer to the User Manual for details.
Pt-2 005
Enter Zone # _ _ _
then +YES or -NO
Ch1 None
cpx 020.qxd 09/08/2006 16:31 Page 27

53) If you do not wish to enter Ch1 Zone press Yes
and jump to Step 57
Otherwise
54) Enter the Zone number you require for Ch1
followed by Yes.
55) To add more Zones to Ch1 repeat from Step 53
56) When you have finished adding Zones to Ch1
press Yes
58) If you do not wish to enter Ch2 Zone press Yes
and jump to Step 62
Otherwise
59) Enter the Zone number you require for Ch2
followed by Yes.
Ch1 001
Ch2 006
Enter Zone # _ _ _
then +YES or -NO
Enter Zone # _ _ _
then +YES or -NO
Ch2 None
cpx 020.qxd 09/08/2006 16:31 Page 28

60) To add more Zones to Ch2 repeat from Step 58
61) When you have finished adding Zones to Ch2 press Yes
(See notes on Sec & Per after step 65).
63) This concludes the Step by Step instruction for the Zone Programming.
You may continue within this section to program
Secondary Zones
Perimeter Zones
Double Knock Time Window
Zone Re-Arm
Zone Log Limit
Zone E/E Mode
Event Tags
64) Press 0 (zero) twice to return to:-
65) At this point you may press No to move to the next
Header.
Or
Press 0 (zero) until the display shows:-
Secondary Zones:
Zones programmed as secondary will not active any sounders or comms until
a normal zone activates.
This will then trigger a confirmed signal and activate the sounders as
programmed.
Perimeter Zone:
Zones programmed as perimeter will activate the alarm as normal but will also
activate a comms channel programmed as perimeter.
DKnock/Arm/Log:
Zones on double knock are required to activate within the double knock time
window or stay active for fifteen seconds to generate an alarm condition.
Arm is used to program the zones to automatically re-arm after an activation.
It should be noted that a zone still violated when the system times out after
an alarm, will not re-armed.
Note: Zone Log Limit is defaulted to On and may not be changed. Only five activations from any
one zone will be recorded in the log during any set period.
Note: E/E in part set entry exit zones will start the entry timer if opened in part set.
12Hr in part set entry exit zones will be instant when opened in part set.
Sec. None
Program . . . . _ _ _
Zones ?
01 Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 29

Reporting a Mains Fail on a PSU.
In order to report a Mains Fail on a PSU the Fault output on
the PSU would be wired to a Zone on the Control Panel.
The Zone Type would be programmed as ‘Fault’.
Program the Zone Descriptor as External PSU.
At the end of the Program Zones menu we have a menu called Program Events Tags,
enter this option and select the Zone number you have programmed as Fault.
Program the Tag as Mains Fail. Then program a Digi Channel as Mains Fail.
This will allow for full reporting of External PSUs.
Page 30
Program Zone
Event Tags ?
cpx 020.qxd 09/08/2006 16:31 Page 30

Programming Setting Modes
Setting Modes are the modes that the control panel will use to set the system for a
particular type of set. An example of this may be that the Full Set Modes is
programmed as Final Exit Door (door opening and closing during exit will set te panel)
whilst the Setting Mode for Part Set 1 is timed. Each type of Set (Full, Part 1, Part 2,
Part 3) may have its own Setting Mode.
1) Enter into Engineer Mode
To do this follow Steps 1 to 4 on page 18
With the display showing:-
5) Press No twice. The display will show:-
6) Enter the time you require as the Exit Time
(in seconds) followed by Yes.
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Setting Modes ?
Program Setting
for FULL set ?
F-Exit time =30s
=Set by TIME
F-Exit time >_ _s
=Set by TIME
F-Exit time =20s
>Set by TIME
cpx 020.qxd 09/08/2006 16:31 Page 31

7) Use the No key to scroll through the
Setting Modes.
Options available for Setting Modes are.
Set By Time The system will Set after the Time shown in the
Exit Time.
Set By ET The system will set when the Exit Terminator Button
outside the premises is pushed (this option will require
a Zone to be programmed as Exit Terminator).
Set By E/E Once the user has started to Set the system the Exit Tones
will continue until the Final Exit Door is opened then closed.
This option will require a Door Contact.
Set By Time+E/E Once the user has started to Set the system the system will
Set on either the Time expiring or the door opening and
closing. This option may require a Door Contact.
8) When the Setting Mode you Require is displayed
press Yes. The display will show:-
Program Setting
for FULL set ?
Program Setting
for PART 1 set ?
P1-Exit time =30s
=Set by TIME
P1-Exit time >_ _s
=Set by TIME
P1-Exit time =20s
>Set by TIME
cpx 020.qxd 09/08/2006 16:31 Page 32

Setting Modes.
14) When the Setting Mode you require is displayed
Setting Modes.
Program Setting
for PART 1 set ?
Program Setting
for PART 2 set ?
Program Setting
for PART 2 set ?
P2-Exit time =30s
=Set by TIME
P2-Exit time >_ _s
=Set by TIME
P2-Exit time =20s
>Set by TIME
cpx 020.qxd 09/08/2006 16:31 Page 33

Setting Modes.
The Final Set Delay is a period of time in seconds after the expiry of the Exit
Time and is intended to allow any PIRs for example that are on the Exit Route to
settle before the system finally Sets. The majority of PIRs will settle within the
Default Time of 3 seconds but some may need a Final Setting Delay of up to 10
seconds.
Program Setting
for PART 3 set ?
Program Setting
Delay ?
Final Set Delay
= 03s
Program Setting
for PART 3 set ?
P3-Exit time =30s
=Set by TIME
P3-Exit time >_ _s
=Set by TIME
P3-Exit time =20s
>Set by TIME
cpx 020.qxd 09/08/2006 16:31 Page 34

30) Enter the Time required (in seconds) followed
by Yes. The display will show:-
Setting Sounders refers to Part-Sets Only
The Setting Sounders option determines if any, or all Part Sets are audible (Exit
Tones) or not. This is a useful feature when part of the family may already be
asleep when the system is being Part Set.
32) Press Yes.The display will show:-
33) Press the No key to scroll through the options
Options available for Setting Sounders are.
Always Audible Exit Sounder will be audible for Full Set and all Part Sets
Silent If Part 1 Exit Sounder will be silent during a Part 1 Set
Always Silent Exit Sounder will be silent during ANY Part Set
When using a silent Part Set a single beep will be heard at the end of the Exit
Time to confirm the system has Set.
34) When you have the required setting displayed
Final Set Delay
> _ _
Program Setting
Delay ?
Program Setting
Sounders ?
Program Setting
Sounders ?
Exit Sounder . .
= Always Audible
cpx 020.qxd 09/08/2006 16:31 Page 35

Setting Confirmation uses the Strobe Light to confirm that the system has finally
set.
37) Press the No key to scroll through the options
Available options for Strobe Confirm are.
Off Strobe Confirm is turned Off
Full-Set The Strobe will Confirm only on Full Set
Any-Set The Strobe will Confirm on Any Set (Full or Part)
38) When the required setting is displayed press Yes.
Auto Part Set allows the system to decide if the Setting should be Full Set or
Part 1 Set. In order to use this option the Setting Mode for Full Set MUST be
Time+E/E and a Door Contact must be fitted to the door.
If the system sees the door open and close during a setting procedure the
system will Full Set.
If the system does not see the door open and close during a setting procedure
the system will Part 1 Set.
It is not possible to use Silent Part Sets with this option as the decision to do a
Part 1 set is taken after the Entry Time has expired.
Program Setting
Confirmation ?
Program Setting
Confirmation ?
Program Setting
for Auto-Part ?
Strobe Confirm
= Off
cpx 020.qxd 09/08/2006 16:31 Page 36

41) To change this press No twice.
43) This concludes the programming for
Setting Modes. Press 0 (zero) to return to:-
Or
Program Setting
for Auto-Part ?
Auto Part-Set
= Off
Auto Part-Set
= On
Program . . . . _ _ _
Setting Modes ?
01 Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 37

Programming Entry Times
Two Entry Times are available (Entry Time 1 & Entry Time 2). On entry to the premises
via the Entry Door Entry Time 1 will start. If deviation from Entry Route during Entry
Time 1 then Entry Time 2 starts. Entry Time 2 is 30 seconds and cannot be changed.
Note that comms cannot take place until the later of the theoretical expiry of Entry
Time 1, or the expiry of Entry Time 2.
Note: Entry Time 1 is defaulted to 30 seconds but maybe changed to a maximum
of 45 seconds.
Note: Entry Time 2 is defaulted to 30 seconds and may not be changed.
6) Enter the Time required (in seconds) followed by
Yes. The display will show:-
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Entry Times ?
Program Entry
Time 1 ?
Program Entry
Time 1 ?
Entry Time 1 = 30s
Entry Time 1 > _ _s
cpx 020.qxd 09/08/2006 16:31 Page 38

Note: Entry Time 2 is defaulted to 30 seconds and may not
be changed.
Warning Bell. Default is set to On but may be changed to Off. If Warning Bell is On, then Bells will
operate during Entry Time 2, after the theoretical expiry of Entry Time 1 has been reached. If set to
Off, the bells will activate only when both Entry Time 1 and 2 have expired.
9) Press No to change the setting followed by Yes
Entry Times. Press 0 (zero) to return to:-
Or
Program Entry
Time 2 ?
Entry Time 2 : 30s
Warning Bell = On
Program . . . . _ _ _
Entry Times ?
01 Jan 00: 00: 01
Program Entry
Time 2 ?
cpx 020.qxd 09/08/2006 16:31 Page 39

Programming Bells / Sounders
2) Press No three times. The display will show:-
For information on NovActive refer to page 89
5) This option should remain Off unless you are
using a NovActive Bell Box
Press Yes. The display will show:-
Two Types of Bell may be programmed.
SAB Self Actuating Bell. The Bell + terminal stands at 12V and the Bell -
terminal switches negative on activation.
SCB Self Contained Bell. The Bell + and Bell - stand at 12V and 0v. The
0V is removed on activation.
The majority of Bells sold in the UK are SAB you should only change the Bell
Type if you are sure the Bell Type you have is SCB.
The other option on this screen may be programmed as
Normal Normal UK trigger for the UK
Irish A Pull-Up resistor is required on the Bell Trigger this option is only
required for the Irish Republic.
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Bells / Sounders ?
Program Bell
Type ?
NovActive = Off
Type = SAB
Normal
cpx 020.qxd 09/08/2006 16:31 Page 40

8) Press Yes. The Display will show:-
10) Enter the number of minutes you require for the
Bell Delay followed by Yes.
Note: Bell delay is defaulted to 0 but maybe programmed to a maximum of 10 minutes.
Be careful when using Bell delay, the Bell will not sound for the period
programmed after the the alarm has been activated. Bell Delay used to be a
Police requirement but is now not often used in the UK.
11) Press No.The display will show:-
Number of Arms is the number of times the bell is capable of sounding during a
Set period. It is normal to set this option to 3 or 4, If left at 99 the number of
Arms is infinite.
Note: If this option is programmed to 0 the bell will not activate.
12) Enter the required Number of Arms followed by
Program Bell
Type ?
Program Bell
Delay / No. Arms ?
Program Bell
Delay / No. Arms ?
Bell Delay = 00 m
No. Arms = 99
Bell Delay = _ _ m
No. Arms = 99
Bell Delay = 00 m
No. Arms > 99
Bell Delay = 00 m
No. Arms > _ _
cpx 020.qxd 09/08/2006 16:31 Page 41

16) Enter the Bell Ring Time you require(in minutes)
followed by Yes. The display will show:-
Note: Bell Ring is defaulted to 10 minutes and is programmable from a minimum of 1 minute to a
maximum of 15 minutes.
The term Sounder refers to the Internal Speakers fitted to the system and also
the speaker(s) fitted to the RKPs
Options available for Sounder are.
Constant Will continue after the Bell Time has elapsed.
Timed Will Time out with the Bell Time
17) Press No until your required setting is displayed
then press Yes. The display will show:-
The Strobe light will normally continue after the Bell Time has elapsed. You may
Time the Strobe if required. To do so.
19) Enter the time required (in minutes) followed by
Note: Strobe Timer is defaulted to 0 minutes but is programmable to a maximum of 120 minutes.
Program Bell
& Sounder Ring ?
Program Bell
& Sounder Ring ?
Bell Ring = 10 m
Sounder = Constant
Bell Ring = _ _ m
Sounder = Constant
Bell Ring = 15 m
Sounder > Constant
Strobe Timer
= 000 m
Strobe Timer
= _ _ _ m
cpx 020.qxd 09/08/2006 16:31 Page 42

With the Bell Tamper Ring On tampering the Bell Box will also trigger the Bell
Output from the control panel. With Bell Tamper Ring of the Bell Trigger from the
panel is not activated.
22) Press No until your required setting is displayed
25) Press No until the required setting is displayed
Bells & Sounders. Press 0 (zero) to return to:-
Or
Program Bell
Tamper Mode ?
Program Bell
Tamper Mode ?
Program Bell
for Part-Set ?
Program Bell
for Part-Set ?
Part-Set Bells
= On
Bell Tamper Ring
= On
Program . . . . _ _ _
Bells / Sounders ?
01 Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 43

Programming Keypad
Up to 4 RKPs (Remote Keypads) may be fitted to The CPX control panel on a 4 wire
BUS. A four core connection will be required between the control panel and the remote
keypad(s), keypads maybe in a “daisy chain” or “star” format
Note: A 680 Ohm resistor must be fitted to ONE RKP. If the RKPs are wired in the “daisy chain”
format then this should be the last in the line.
Note: Each keypad must be programmed onto the system in order for it to be recognised by the
system.
Note: Depending on the variant of the keypad fitted,external G-Tag Proximity Reader(s) may be
fitted to each keypad.
2) Press No four times. The display will show:-
Alert 1 Keys refers to the PA keys being pressed together or keys 1&3 being
pressed together. P&F refers to PA keys.
5) Press the No Key to scroll through the settings
for Alert 1. When the setting you require is
displayed press Yes. The display will show:-
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Keypad ?
Program Keypad
Alert 1 Keys ?
Alert 1 =Off
1&3 = Off P&F = On
Alert 1 =Off
1&3 > Off P&F = On
Alert 1 =Off
1&3 > On P&F = On
Alert 1 =Off
1&3 = On P&F > On
cpx 020.qxd 09/08/2006 16:31 Page 44

Alert 2 Keys refer to Key 7&9 pressed together.
Program Keypad
Alert 1 Keys
Program Keypad
Alert 2 Keys
Program Keypad
Alert 2 Keys
Program Keypad
Quick Key ?
Quick Key
= Off
Alert 2 = Off
7&9 Keys = Off
Alert 2 = Off
7&9 Keys > Off
Alert 2 = Off
7&9 Keys > On
cpx 020.qxd 09/08/2006 16:31 Page 45

The available options for the Quick Key are.
Off The Quick Key is disabled
Quick-Set Reduces the Exit Time after Exit has started.
Full-Set Enter user code then Quick Key
Part-Set Enter user code then Quick Key for Part 1 Set
This option is used to program the Number of Keypads you have on the system.
It should be noted the there are no jumpers in the RKP to ident them this is done
from the program option.
20) Enter the Number of the keypad you wish to
program onto the system (1 to 4) then press
21) Press the No & the Yes buttons together on the
selected keypad. The display will show:-
Program Keypad
Quick Key ?
Program Keypad
Number ?
Install Keypad ?
Enter Keypad # _
then +YES or -NO
Press NO + YES on
Selected Keypad
Keypad Installed
OK . . .
cpx 020.qxd 09/08/2006 16:31 Page 46

Then:-
22) Repeat from Step 19 until all the RKPs have
ben installed onto the system.
23) Press 0 (zero). The display will show:-
Note: Use of this option will require a compatible G-Tag RKP.
Default is Off, but maybe changed to On. It is intended for use with the external prox reader
(E-Reader) and monitors the antenna of the reader for being disconnected.
Keypad. Press 0 (zero) to return to:-
Or
Program Keypad
Number ?
Program Keypad
Backlight Mode ?
Program Keypad
Backlight Mode ?
Backlight . . .
= On if EE/Key
Enter Keypad # _
then =YES or -NO
Program . . . . _ _ _
Keypad ?
01 Jan 00: 00: 01
Program Keypad
ACE/Prox ?
Prox Tamp. Detect
=Off
Program Keypad
ACE/Prox ?
cpx 020.qxd 09/08/2006 16:31 Page 47

Programming Digicom / Vo-Comm Off/On
Within this section we will program the Digicom and Modem. Both of these devices are
built on the main PCB of the control panel. Only the main functions will be covered
within this Step by Step section.
If required, the 5, 5, Yes, No default may be used to set the basic comms
configuration. When this default is used all other settings that have been
programmed will be returned to factory defaults. When this default is used the
following will be set.
Digicom Type Mod+F/F
Modem Mode No Return
This will allow for connection to GardTec Remote for programming functions.
2) Press No five times. The display will show:-
Digicom Types available are.
Mod+F/F Modem enabled and Ademco Fast Format Central
Station protocol enabled.
Mod+SIA Modem enabled and SIA Central Station protocol enabled.
Mod+PID Modem enabled and Point ID Central Station protocol
enabled.
For programming details on PID (Point ID Protocol) and SIA please refer to page 91
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Digicom ?
Program Digicom
Type or Test ?
Digicom Type . . . .
=Mod+F/F
cpx 020.qxd 09/08/2006 16:31 Page 48

5) Press No until the required setting is displayed,
Note: If On is selected, the Vo-Comm menu will now appear in the USER
mode. Please refer to CPX User Guide for further programming
information.
6) Press No until the setting you require is displayed,
11) Enter the number of seconds you require for
the Fire Zone Delay, followed by Yes.
With Digi Delay programmed, the alarm transmission to Central Station will be
delayed for the number of seconds programmed.
With Part Alarm programmed to Off there will be no transmission of Alarm,
Alarm B or Alarm Abort if the system is Part Set.
13) Enter the number of seconds you require for
the Digi Delay in Part Set followed by Yes.
Test Digicom
Channels ?
Program Digicom
Type or Test ?
Program Digicom
Delay / Part
Program Digicom
Delay / Part
Program Digicom
Channels
Digi Delay = 00s
Part - Alarm = On
Digi Delay = _ _s
Part - Alarm = On
Digi Delay = 99s
Part - Alarm > On
VoComm
=Off
Fire Zone Delay
=90 Secs
Fire Zone Delay
>-- Secs
cpx 020.qxd 09/08/2006 16:31 Page 49

When programming Digicom Channels Channel 1 is normally Fire, Channel 2 is
normally PA (Panic), Channel 3 is normally Alarm (unconfirmed) and Channel 4
is normally Open/Close.
Channels 5, 6, 7 & 8 will be advised by your Central Station.
Other signals you may require for DD243 are.
Alarm Abort
Zone Exclude
Alarm B (Confirmed)
Channel settings available are.
Off
Zone 24Hr
Gen. Tamper
Alert
Fire
Part-Set
Open/Close
Panic
Alarm
Alarm B
Alarm Abort
Power Fail
Watchdog
Mains Fail
Perimeter
Zone Exclude
Const. Lo-Bat (Radio)
Radio Lost (Radio)
Const. Jjam. (Radio)
17) Press No until the required setting is displayed.
Ch1 = Off
Ch4 = Off
Ch1 = Off
Ch4 >Off
cpx 020.qxd 09/08/2006 16:31 Page 50

28) Press Yes the display will show:-
Ch2 = Panic
Ch3 = Alarm
Ch5 = Off
Ch6 = Off
Ch5 = Off
Ch6 > Off
Ch7 = Off
Ch8 = Off
Ch2 = Panic
Ch3 > Alarm
cpx 020.qxd 09/08/2006 16:31 Page 51

29) Press No until he required setting is displayed.
37) Press Yes if you require connection to a local PC.
Otherwise
Ch7 = Off
Ch8 > Off
Program Digicom
Channels ?
Program Digicom
Functions ?
Program Modem
Functions ?
Modem Mode
=Off
View Modem Log ?
Access Via
Local PC ?
Remote Access
cpx 020.qxd 09/08/2006 16:31 Page 52

Choose from the following settings.
No Return Communication to the panel is from GardTec Remote via
Patch Lead or PC Modem.
Return PC The panel will ring the PC back on the number the PC has passed
to the panel.
Return
#1 or #2 The panel will ring back the PC on the #1 or #2 number programmed
into the panel.
Return #1 Only The panel will ring back the PC on the #1 number programmed
into the panel.
Return #2 Only The panel will ring back the PC on the #2number programmed
into the panel.
From Site Only Remote Access will be initialised by the user On-Site.
Off Modem Functions are disabled.
This option may be used when when the panel is on a shared line and GardTec
Remote is also used.
You may continue to program other Modem options if required. For the purpose of this
Step by Step section.
41) Press 0 (zero). The display will show:-
Double Ring
= Off
Program Comms
Functions ?
Comms = Off
Keypad Lock = Off
In-Use Text = Off
cpx 020.qxd 09/08/2006 16:31 Page 53

44) Press Yes. The display will show for example:-
In the UK the Site ID Code is normally a four digit number, your Central Station
may have supplied you with a six digit number. If this is so please use the last
four digits.
46) Enter your Site ID Code followed by Yes.
We will be entering two Phone Numbers. If your Central Station has only
supplied you with one Phone Number please use the same one twice.
48) Enter Phone Number one followed by Yes.
Comms = On
Site ID Code
Is Un-Programmed
Site ID Code
_ _ _ _ _ _ _ _
Phone Number 1
is Un-Programmed
Phone Number 2
is Un-Programmed
Phone Number 1
_ _ _ _ _ _ _ _ _ _ _ _ _
Phone Number 2
_ _ _ _ _ _ _ _ _ _ _ _ _
Inhibit Display
of New Number ?
cpx 020.qxd 09/08/2006 16:31 Page 54

51) Enter Phone Number 2 followed by Yes.
This option refers to the line mode of the telephone line. In the UK most
telephone lines are Tone Dial.
53) Press No until the required setting is displayed, then
Settings available for Line Monitor are.
Tone + Volts The Line Monitor will check the Dial Tone and the Line Voltage
This setting should be used when the control panel is
connected to a dedicated telephone line.
Off Line Monitor is turned Off
Dial Tone The Line Monitor will only monitor the Dial Tone. This setting
should only be used on a dedicated telephone line.
Line Volts Then Line Monitor will monitor the Line Voltage. This setting
should be used when the control panel is connected to a
telephone line that has other telephone equipment on it
(shared line).
Settings available for Line Security are:-
High The Line Voltage is monitored at a High Level. This setting should
be used on dedicated lines only.
Low The Line Voltage is monitored at a Low Level. This setting should
be used when the control panel is sharing the line with other
telephone equipment.
Inhibit Display
of New Number ?
Dial = Tone
Line Monitor
= Tone + Volts
Line Security
= High
cpx 020.qxd 09/08/2006 16:31 Page 55

This option determines what Digi Channels will send a Restore Signal to Central
Station when the system is Reset. Most Central Stations will require a Restore
Report for all channels.
57) Enter eight ones so the display shows:-
Channel 4 normally needs an inversion of the signal that is sent to Central
Station. By having 4 as the setting for this option channel 4 will be inverted. If
you have reports from the Central Station that the Open/Close channels are the
wrong way around proceed as follows to remove the inversion on the control
panel.
59) If you do not need to change this option press
Yes and jump to Step 61.
Or
To change the setting. Press No.
60) Press 0 followed by Yes. The display will show:-
Channel 1 2 3 4 5 6 7 8
R/Rep = 0 0 0 1 0 0 0 0
Channel 1 2 3 4 5 6 7 8
R/Rep = _ _ _ _ _ _ _ _
Channel 1 2 3 4 5 6 7 8
R/Rep = 1 1 1 1 1 1 1 1
Open/Close
Channel/s = 4
Open/Close
Channel/s > _ _
Program Advanced
Functions ?
cpx 020.qxd 09/08/2006 16:31 Page 56

You may continue to program other Advanced options if required. For the purpose of
this Step by Step section.
61) Press 0 (zero) three times. The Display will show:-
Program . . . . _ _ _
Digicom ?
cpx 020.qxd 09/08/2006 16:31 Page 57

Programming Linefault Modes
2) Press No six times. The display will show:-
8) Press No until the display shows the required setting
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Linefault Modes ?
Program Linefault
Sounders ?
Linefault Sounders
=ON if Un-Set
Program Linefault
Sounders ?
Program Lineflt
Mode in Exit ?
Program Lineflt
Mode in Exit ?
Lineflt Mode . . .
= Detect in Exit
cpx 020.qxd 09/08/2006 16:31 Page 58

Note: Line Fault is defaulted to Limited and may not be changed.
This limit is set to 3 events.
With Detect programmed as 00 Linefault detection is instant or it may be delayed
if required.
15) Enter the time you require (in seconds) followed
by Yes. The display will show:-
Linefault Sounders. Press 0 (zero) to return to:-
Or
For information on Linefault Sounders refer to page 93
Program Lineflt
Log Mode ?
Program Lineflt
Log Mode ?
Program Lineflt
Detect Time ?
Program Lineflt
Detect Time ?
Detect
= 30 Secs
Detect
> _ _ Secs
Lineflt Log
: Limited
Program . . . . _ _ _
Linefault Modes ?
01 Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 59

Programming Panic
Note: Duress is defaulted to Off and cannot be changed. Duress 7 is now no
longer available.
You should also check current legislation if Panic signals are allowed for the grade of
system that you are fitting.
2) Press No seven times. The display will show:-
It should be noted that with PA = Bells Only no PA signals will be sent to Central
Station.
Available setting for PA are
Bells Only Activating a Panic will only sound the Bells.
Bells Always Activating a Panic will Sound the Bells and send a signal
to Central Station provided that a Digi Channel is
programmed as Panic.
Silent Always Activating a Panic will only send a signal to Central Station
providing that a Digi Channel has been programmed as
Panic.
Bells if LFlt As Silent Always but will revert to Bells if a Linefault is
present.
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Panic / Duress ?
PA = Bells Only
= Non-Testable
cpx 020.qxd 09/08/2006 16:31 Page 60

Note: Duress is defaulted to Off and may not be changed.
7) Press 0 (zero) until the display shows:-
PA = Bells Only
> Non-Testable
Duress :Off
Program . . . . _ _ _
Panic / Duress
01 Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 61

Programming PGM2 / 3 / Timers
PGM2 refers to the PGM2 terminal on the control panel PCB situated near to the RKP
terminals.
PGM3 Refers to the Strobe terminal, if this is not used for the Strobe (for example if a
NovActive Bell Box is used) it may be re-programmed for other uses.
One Timer is also available. It should be noted that the times programmed will operate
seven days per week, you are not able to program separate time for weekends etc.
2) Press No eight times. The display will show:-
Options available for PGM2 / 3 are.
Bell
Strobe
Latch Any
Any Digi
Status
Perimeter
Zone Exclude
Custom 1 to 8
Int. Sounder
E/E
Timed 1
Alert
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
PGM2 / 3 / Timers ?
Program PGM2 / 3
Operating Modes ?
PGM2 O/P
= Bell = +V
cpx 020.qxd 09/08/2006 16:31 Page 62

cont-
Alarm B (Confirmed)
Alm Abort (Alarm Abort)
Any Fire
Any Panic
Gen. Tamper (General Tamper)
Zone - 24Hr
Power Fail
Power OK
Const. LoBat (Radio Low Battery)
Radio Lost (Lost Radio Detector etc.)
Const.Jamm. (Radio Signal Jamming)
Any Fault
Any Mask
Watchdog
Off
Pulse Off
Pulse On
Any Set
Alarm (Unconfirmed)
After Alarm
Open / Close
Pulse Set
Part Set
Walktest
Mains Fail
then press Yes. The display will show for example:-
With the PGM2 programmed as Bell the output will operate with the Bell when this is
set as +V. With this set as -V the output will be inverted e.g On, turning Off with the
Bell.
Program PGM2 / 3
Operating Modes ?
PGM2 O/P
= Bell > +V
PGM3 O/P
= Strobe > +V
cpx 020.qxd 09/08/2006 16:31 Page 63

10) Press twice No. The display will will show:-
11) Enter the On Time hours followed by Yes.
13) Enter the On Time minutes followed by Yes.
Repeat for Timer 1 Off Time
15) Press Yes. The display will Show:-
Program PGM2 / 3
Timer 1 On Time ?
Program PGM2 / 3
Timer 1 On Time ?
Program PGM2 / 3
Timer 1 Off Time ?
Timer 1 On Time
= 00:00 Hrs
Timer 1 On Time
> _ _ : 00 Hrs
Timer 1 On Time
= 10:>00 Hrs
Timer 1 On Time
= 10:>_ _ Hrs
Program PGM2 / 3
Timer 1 Off Time ?
cpx 020.qxd 09/08/2006 16:31 Page 64

16) This concludes the programming for PGM2/3/Timer
17) Press 0 (zero) to return to:-
Or
Program . . . . _ _ _
PGM2 / 3 / Timers ?
01 Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 65

Programming Reset Modes
2) Press No nine times. The display will show:-
4) Press No twice, then enter the Mains Fail Delay
time you require.Then press Yes. The display will
show:-
Note: Default is set at 20 minutes. Will delay the display and the
necessity to reset a mains fault for the time programmed.
Then press Yes. The display will show:-
When Alarm Restore is turned On the Digi channels programmed with Restore On will
be restored when the system is unset rather than when the system is Reset.
then press Yes. The display will show for example:-
8) Press No until the required abort time is set
followed by Yes. (0-180 seconds in increments of
20 seconds).
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Reset/Mains ?
Program . . . . _ _ _
Reset/Mains
Alarm Reset
= Master
Tamper Reset
=Eng. +Anti
Alrm Restore = Off
Abort Time = 60s
Alrm Restore = On
Abort Time > 60s
Alrm Restore = On
Abort Time > 60s
Mains Fail Delay
=20m
cpx 020.qxd 09/08/2006 16:31 Page 66

Reset Modes.
11) To return to:-
Press 0 (zero) twice
01 Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 67

Programming Sounder Levels
2) Press No ten times. The display will show:-
6) Enter a value 1 to 9 (1=Low 9=High) followed by
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Sounder Levels ?
Program Sounder
Chime Level ?
Program Sounder
Chime Level ?
Program Sounder
Ent / Exit Level ?
Ent / Exit Level
= 05
Chime Level . . . . .
= 05
Chime Level . . . . .
= _ _
cpx 020.qxd 09/08/2006 16:31 Page 68

10) Enter a value 1 to 9 (1= Low 9 = High) followed by
14) Enter a value 1 to 9 (1 = Low 9 = High) followed by
15) This concludes the program Sounder Levels
press 0 (zero) to move back to:-
Then Press 0 twice to move back to:-
Program . . . . _ _ _
Sounder Levels ?
Program Sounder
Ent / Exit Level ?
Program Sounder
Keypad Level ?
Program Sounder
Keypad Level ?
Keypad Level . . . .
= 05
Keypad Level . . . .
= _ _
Ent / Exit Level
= _ _
< < < < UN-SET > > > >
01 Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 69

Programming PGM1 / Custom
PGM1 is located on the control panel PCB close to the Bell terminals.
Up to 8 custom outputs may be programmed on to PGM 1 to 3. A custom output may
be used so that the output can follow a zone or a user code.
2) Press No eleven times. The display will show:-
The options available for PGM1 are shown on page 62.
With the PGM2 programmed as Bell the output will operate with the Bell when this is
set as +V. With this set as -V the output will be inverted e.g On, turning Off with the
Bell.
5) Press No. until the required setting is displayed
6) Press No to change the Cus 1 to Zone, Code or
Group as required to follow. Press Yes.
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
PGM1 / Custom ?
PGM1 O/P
= Pulse Off =+V
PGM1 O/P
= Pulse Off >+V
Cus 1 = Zone #=000
=Day = Fol+ t=00
Cus 1 = Zone #>000
=Day = Fol+ t=00
cpx 020.qxd 09/08/2006 16:31 Page 70

8) Enter the Zone Number or Customer Number
that you wish the output to follow then press
Yes. The display will show for example:-
9) Press No to select when you want the output to
operate followed by Yes. The display will show:-
10) Press No until the mode you require is displayed
12) Enter the time required followed by Yes.
The t = 00 setting only applies to Fol+
Fol- Pul+ Pul-
13) Repeat Steps 5 to 13 until all the Custom
Outputs you require have been programmed.
When you have programmed Custom 8 the
display will show:-
14) Press 0 (zero) until the display shows:-
Program . . . . _ _ _
PGM1 / Custom ?
Cus 2 = Zone #=000
=Day = Fol+ t=00
Cus 1 = Zone #>_ _ _
=Day = Fol+ t=00
Cus 1 = Zone #>009
>Day = Fol+ t=00
Cus 1 = Zone #>009
+Day > Fol+ t=00
Cus 1 = Zone #>009
+Day = Fol+ t>00
Cus 1 = Zone #>009
+Day = Fol+ t> _ _
01 Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 71

Programming Engineer Code
2) Press No twelve times. The display will show:-
4) Enter your New Engineer Code (4, 5 or six digits)
followed by Yes. The display will show:-
Be careful if you lock your code in. If the code is forgotten you may have to
return the control panel to the factory to have it unlocked, this will be a
chargeable service.
6) This concludes the Program Engineer Code
Press 0 (zero) twice to return to:-
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Engineer Code ?
Program . . . . _ _ _
Engineer Code ?
Now Enter Code
_ _ _ _ _ _ Then YES
Code = Unlocked
01 Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 72

Programming Service
Within this section you will program the Service Timer. Also, if required, uploading /
downloading data to the control panel via the PTM (Program Transfer Module). The
Service Timer has the ability to Lock a user out of the system when the Service Time
expires. Trading Standards may take action if a Lockout occurs and no Service
Contract exists. Please use with care.
2) Press No thirteen times. The display will show:-
4) Press Yes if you require to save to PTM
Otherwise
5) Press No. The display will :-
6) Press Yes if you require to load from the PTM
Otherwise
Note: To transfer data to and from the PTM, a cable (part number 04-091) will be
required. Cut off the BLUE plug at one end and wire to the RS485 terminal block on
the CPX control panel PCB following the colour code. Connect the other end to the
PTM.
Note: When data transfer is in progress, the LED on the PTM will flash rapidly.
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Service / PTM ?
Service Timer
= Off
Service Timer
> On
Next Service due
in 00 Weeks
Save Panel NVM
to PTM ?
Load Panel NVM
from PTM ?
cpx 020.qxd 09/08/2006 16:31 Page 73

11) Enter the number of weeks you require to the
next Service then press Yes.
Note: The system will start to warn the end
user that the Service is due two weeks
before the time expires.
13) Enter the Telephone Number you wish your
customer to dial for service followed by Yes.
With Lock - Out turned On the system will
Lock the users out when the Service Time
expires.
With Lock - Out turned Off the system will
continue to warn of Service until the Service
Timer is reset.
With Engineer Mode programmed as Constant
the panel will remain in Engineer Mode until
the Engineer exits.
With Engineer Mode programmed as timed the
panel will jump out of Engineer Mode after 1 hour
if all the Tampers are clear. This prevents the
Engineer accidentally leaving the panel in
Engineer Mode.
16) This concludes the Program Service
Service Tel. No.
_ _ _ _ _ _ _ _ _ _ _ _ _
! ! ! LOCK - OUT ! ! !
= On
Engineer Mode
= Constant
Program . . . . _ _ _
Service / PTM ?
01 Jan 00: 00: 01
Next Service due
in _ _ Weeks
Service Tel. No.
is Un-Programmed
cpx 020.qxd 09/08/2006 16:31 Page 74

Programming Custom Screens
2) Press No fourteen times. The display will show:-
Note: The LCD Status is defaulted to None and may not be
changed. The display will only show the Set / Unset status of the system for ten seconds after a Set
or Unset.
The LED Status refers to the LED in the G-Tag ‘E’ or ‘I’
reader. Choose from:-
Off The reader LED will only show for
ten seconds after a Set / Unset
On The reader LED will always be
active.
6) This concludes the Program Service
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Custom Screens ?
LCD Status
:None
LED Status
= Off
Program . . . . _ _ _
Custom Screens ?
01 Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 75

Programming Diagnostics / Log
The CPX control panel has some limited diagnostic features available to the engineer.
To access these proceed as follows.
2) Press No fifteen times. The display will show:-
4) Press Yes if you wish to view the Event Log
This is the last event in the Log
Use the No key to move backward in the Log
Use the Yes key to move forward in the Log
5) When you have finished viewing the Log press
0 (zero). The display will show:-
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Diagnostics / Log ?
Program . . . . _ _ _
Diagnostics / Log ?
List
Event Log ?
Eng Code
01 Jan 01:18:12
cpx 020.qxd 09/08/2006 16:31 Page 76

6) Press Yes. the display will show:-
A PSU/Battery test will be carried out at the time
interval set here and each time you leave Engineer
Mode. This may be turned Off by setting the Time
interval to 0 (zero).
11) Enter the time you require (in hours) followed by
In this example any voltage over 14V or below
13V will create a warning when the PSU test
is performed by the system.
13) To change these limits. Press No until the required
setting for V.Max is displayed then press Yes.
List
Event Log ?
Change / List
Diagnostics ?
PSU . . .
Diagnostics ?
PSU Test Time
= 01 Hrs
PSU Test Time
= _ _ Hrs
Change / List
Test Limits ?
Aux. VMax = 14.0V
Aux. VMin = 13.0V
Aux. VMax = 14.0V
Aux. VMin > 13.0V
cpx 020.qxd 09/08/2006 16:31 Page 77

14) Press No until the setting required for V.Min is
displayed then press Yes.
15) Press No until the required setting for On-Charge
Volts max (Battery) is displayed then press Yes.
16) Press No until the required setting for On-Charge
Volts min (Battery) is displayed then press Yes.
17) Press No until the required setting for Off-Charge
Volts max (Battery) is displayed then press Yes.
18) Press No until the required setting for Off-Charge
Volts min (Battery) is displayed then press Yes.
PSU . . .
Diagnostics ?
PSU Test Time
= 01 Hrs
Change / List
Test Limits ?
On - Chg. max = 14.0
On - Chg. min = 12.6
Off - Chg. max = 14.0
Off - Chg. min = 12.6
Off - Chg. max = 14.0
Off - Chg. min > 12.6
On - Chg. max = 14.0
On - Chg. min > 12.6
cpx 020.qxd 09/08/2006 16:31 Page 78

The readings given from this point on are intended as Indicator Only and should
be confirmed with a calibrated Test Meter.
21) Press No. The display will show for example:-
22) Press Yes. The display will show for example:-
The backlight will Dim at this point.
25) This concludes the Program Diagnostics
Aux. Volts
13.6V
Aux. Volts
13.6V
Battery Volts
On Charge 13.6V
Battery Volts
Off Charge 12.9V
01 Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 79

Programming Alarm Confirm
This section is used to program options that are relevant to DD243. Before
programming these options please take time to read the following notes that will help in
your understanding of DD243.
All communications systems that require a Police URN will need to conform to DD243.
These notes intended as a guide only and should be read in conjunction with the
relevant standards relating to the alarm system giving particular attention to
EN50131-1and DD243. These may be obtained from the British Standards Institute.
DD243 options available are.
Confirm Time Window (default = 60)
This time window may be programmed between 1 and 120 minutes. To comply the
required time should be between 30 and 60 minutes.
Confirm on Entry (default = On)
This option may be programmed to On or Off. If Confirm on Entry = Off then confirmed
alarms to central station are disabled if the entry timer is started. If ACE or G-Tag is
used then it is permissible to set this option to On.
Sounder Mode (default = Unconfirmed)
This option controls the system speakers fitted, options are confirmed or un-confirmed.
If Sounder Trigger = Confirmed then internal sounder will only trigger with a confirmed
alarm.
If Sounder Trigger = Unconfirmed then internal sounders will trigger with un-confirmed
alarms.
This feature is not mandatory for DD243
Reset Mode (default = Any)
Choose from Any or Normal.
If Unconfirm = Any then any code can be used to reset an un-confirmed alarm.
If Unconfirm = Normal then the programmed reset mode for alarm will still be required
i.e. if alarm reset has been programmed as engineer and Unconfirm reset is Normal
then an engineer reset will be required for Un-confirmed alarms.
Confirm Secondary Time Window (default = 60 minutes)
This time window may be programmed between 1 and 120 minutes we would suggest
a time between 30 and 60 minutes but should typically be the same time as the
confirm time window. This option affects zones that have been allocated as secondary
zones only. For functionality please refer to Secondary Zones Below.
cpx 020.qxd 09/08/2006 16:31 Page 80

ET (Exit Terminator) Mode (default = Set)
If ET Mode = Set then the exit terminator zone will terminate the exit procedure.
If ET Mode = Door Lock and the ET zone (door lock) is operated on entry then all
confirmed alarms will be disabled.
Bell Mode (default = Unconfirmed)
This option controls the bells fitted to the system, options are confirmed or un-
confirmed.
If Bell Trigger = Confirmed then Bell will only trigger with a confirmed alarm.
If Bell Trigger = Unconfirmed then Bell will trigger with un-confirmed alarms.
Strobe Mode (default = Unconfirmed)
This option controls the Strobe(s) fitted to the system, options are confirmed or un-
confirmed.
If Strobe Trigger = Confirmed then Strobe will only trigger with a confirmed alarm.
If Strobe Trigger = Unconfirmed then Strobe will trigger with un-confirmed alarms.
This gives the ability to show to the keyholder from outside the premises that a
previously unconfirmed alarm is now confirmed.
Confirmed Start Delay (default = 000m)
May be programmed between 0 & 120 minutes (default 0).
If programmed to anything other than 0 the panel cannot send confirmed signals until
the time programmed has expired. This time starts when the system has set and will
prevent confirmed alarms being generated in situations when a person has been
accidentally locked in the building.
Ace Low Battery (default = On)
Options are On or Off. This option allows for the use of new control panel boards with
V5.1 or later software to be used with earlier keypads. If older non DD243 compliant
type keypads are used with V5.1 or later this option should programmed to Off. It is a
requirement of DD243 2002 that when using ACE Low Battery is reported to the end
user if the system is set using ACE.
Secondary Zones
The Program Part / Test /Chime option has now been renamed to Program Zone
Attributes. Within this section you are able to allocate zones as Secondary Zones.
Secondary type zones would be used for detectors that may be deemed as having an
over sensitive nature, this will stop unwanted user call-outs. Zones that are entered as
Secondary will follow the chain of events below.
cpx 020.qxd 09/08/2006 16:31 Page 81

During a set period triggering a Secondary Zone will start the Secondary Time
Window. This will be logged but no further action is taken. If the second zone to alarm
during the same set period is also a Secondary Zone then it will be logged and the
Secondary Time Window will be restarted.
If the time set within the Secondary Time Window is still running and a zone that is not
allocated as a Secondary Zone is triggered the event will be logged an Alarm A (un-
confirmed) and Alarm B (confirmed) will be transmitted.
Perimeter Zones
Within the Program Zone Attribute section you are able to allocate zones as Perimeter.
Zones that are entered as Perimeter will follow the chain of events below.
When activated an unconfirmed alarm will be transmitted to the central station. An
output or digi channel may be programmed as perimeter (or if using Point ID a new
signal type of perimeter will be sent). This will allow central station to inform the
keyholder that an unconfirmed alarm has been received and is a perimeter type device
i.e window backdoor etc. etc. This feature is not mandatory for DD243.
Scenarios Relating to DD234.
Sounder / Bell Considerations
Please note careful consideration should be given when programming Confirm
Sounder and Confirm Bell Modes. If both are programmed for confirmed and any of the
above scenarios occur no local sounders will activate.
Other DD243 Notes to Consider
When a system auto re-arms with a zone in fault condition The GardTec control panel
will omit the zone concerned. A signal should be sent to the central station indicating
that a detector(s) has (have) been isolated. To achieve this a Digi channel should be
programmed as Zone Exclude, this will automatically send the required signal as the
detector is omitted.
See A.3.1 DD243 IAS Incorporating Sequential Conformation Technology Only
New Output Option (Status)
A new output option of Status has been added, this option has three operating modes
and is intended to provide a visual indication of the system status.
System Set Output On for 10 seconds
System Unset Output On for 1s Output Off for 1s for a 10 second period
Confirmed Alarm Output On for 3 seconds Output Off for 1s until system
reset.
It is envisaged that this status output would be fitted to an indicator (i.e. LED) that can
be seen from outside the premises.
cpx 020.qxd 09/08/2006 16:31 Page 82

a) Scenario specific to systems using completion of unsetting with ACE
6.4.5 DD243.
Event 1 System Set
Event 2 Entry Time Starts
Event 3 Access Zone Triggered
Event 4 Entry Expired (including Entry Time 2) Unconfirmed
Transmitted
Event 5 non entry/access Zone Triggered
Event 6 Second non entry.access Zone Triggered Confirmed
Transmitted
To achieve the above
Confirm on entry = On
Ace Low Battery = On
b) Scenario Unlocking the initial entry door disables all means of
conformation 6.4.3 DD243.
Event 1 System Set
Event 2 Entry Door Unlocked Confirmed Alarms Disabled
Event 3 Open Entry Door (entry time starts)
Event 4 Entry Time Expires (inc Entry Time 2) Unconfirmed Alarm
Transmitted
Event 5 Any subsequent zones triggered No Confirmed Signals
Transmitted
Or
Event 1 System Set
Event 2 Entry Door Forced Open (entry time starts)
Transmitted
Event 4 non entry/access Zone Triggered
Event 5 Second non entry.access Zone Triggered Confirmed
Transmitted
Confirm on entry = On
ET Mode = Door Lock
Door Lock Zone programmed as ET
cpx 020.qxd 09/08/2006 16:31 Page 83

c) Scenario Opening the initial entry door disables all means of
conformation 6.4.4 DD243 2002.
Event 1 System Set
Event 2 Entry Door Opened (entry time starts) Confirmed Alarms
Disabled
Transmitted
Event 4 Any subsequent zones triggered No Confirmed Signals
Transmitted
Confirmed on entry = Off
Programming Alarm Confirm
2) Press No sixteen times. The display will show:-
6) Enter the time you require followed by Yes.
The time MUST be between 30 & 60 minutes
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Alarm Confirm ?
Program Confirm
Window Time ?
Confirm Window
= 060m
Confirm Window
> _ _ _m
cpx 020.qxd 09/08/2006 16:31 Page 84

Confirm on Entry may be On only if you are
using an ACE device to Unset the system.
The term Sounder relates to the system speaker(s)
Program Confirm
Window Time ?
Program Confirm
On Entry ?
Program Confirm
On Entry ?
Program Confirm
Sounder Mode ?
Program Confirm
Sounder Mode ?
Program Confirm
Reset Mode ?
Unconfirm Reset
= Any ?
Sounder Trigger
= Unconfirmed
Confirm on Entry
= On
cpx 020.qxd 09/08/2006 16:31 Page 85

17) Press No. The Display will show:-
20) Enter the time required then press Yes.
Program Confirm
Reset Mode ?
Program Confirm
Secondary Time ?
Program Confirm
Secondary Time ?
Program Confirm
ET Mode ?
Program Confirm
ET Mode ?
Program Confirm
Bell Mode ?
ET Mode
= Set Only
Secondary Window
= 060m
Secondary Window
= _ _ _m
cpx 020.qxd 09/08/2006 16:31 Page 86

33) Enter the time required followed by Yes.
Bell Trigger
= Unconfirmed
Program Confirm
Bell Mode ?
Program Confirm
Strobe Mode ?
Program Confirm
Strobe Mode ?
Program Confirm
Start Delay ?
Program Confirm
Start Delay ?
Start Delay
= 000m
Start Delay
> _ _ _m
Strobe Trigger
= Unconfirmed
cpx 020.qxd 09/08/2006 16:31 Page 87

Always On = Keypad is always active.
Off in Entry = Keypad is disabled during
Entry Time.
Of in Ent/Alm = Keypad is disabled during
Entry time or if Entry Time
goes through into Alarm.
40) This concludes the Program Diagnostics
Press 0 (zero) three times to return to:-
Program Confirm
Comms. Restore ?
Program Confirm
Keypad Opening ?
Program Confirm
Keypad Opening ?
Keypad Opening
= Always On
Program Confirm
Comms. Restore ?
Comms. Restore
= On
01Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 88

NovActive Description & Programming
NovActive utilises a four core bus to the NovActive sounders that are fitted to the
system. This allows each individual Bell to to programmed and also gives access to
unique Diagnostic Features that allow the individual NovActive sounders to be
diagnosed from either the control panel or via GardTec Remote PC Software. GardTec
Remote may be used from either a remote location via a Modem or on-site via a
GardTec Modem Patch Lead.
To program the NovActive sounder(s) please follow the instructions below.
Wiring of the NovActive should be carried out in conjunction with the instructions
supplied with the unit.
2) Press No three times. The display will show:-
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Bells / Sounders ?
Program Bell
Type ?
NovActive = Off
NovActive > On
Select NovActive
1 - 8
cpx 020.qxd 09/08/2006 16:31 Page 89

7) Press the number of the NovActive you wish to
program. The display will show:-
8) Press No twice to turn NovActive 1 On. Then press
To program the LED pattern press No until the
setting required is displayed.
Choose from.
0 = Alternating LEDs
1 = 1 Static LED
2 = 2 Pulsing LEDs
3 = No LEDs
9) When you are happy with your selection press
To program the Setting Confirmation press No
until the required setting is displayed then press
10) To programme the sound, press No until the
required setting is displayed, then press Yes.
11) Repeat for Alm, Tmp until the required settings are
displayed.Then press Yes. The display will show:-
13) Enter the text required. E.g. Front Wall Bell. Then
Note: See Page 10 for entering text instructions.
You should now repeat until all the NovActives on the system have been
programmed.
14) When you have finished programming all the
NovActives press 0 until the display shows:-
NovA1 = Off LEDS = 0
Confirm = Off
NovA1 Text =
NovActive
NovA1 = On LEDS > 0
Confirm = Off
NovA1 = On LEDS > 0
Confirm > Off
01 Jan 00: 00: 01
NovA1 A=
PA=0 Alm=0 Tmp=0
NovA1 A=
PA=3 Alm>0 Tmp=0
NovA1 Text =>
-
Select NovActive
1-8
cpx 020.qxd 09/08/2006 16:31 Page 90

Programming Point ID & SIA Protocols
2) Press No five times. The display will show:-
4) Press Yes. The display will show, for example:-
5) Press No until the display shows:-
Or:-
As required
7) Press No until the setting you require is displayed.
Then press Yes. The display will show:-
Program . . . . _ _ _
Zones ?
Program . . . . _ _ _
Digicom ?
Program Digicom
Type or Test
Program Digicom
Type or Test
Program Digicom
Delay / Part ?
Program
Triggers ?
= Mod + FF
= Mod + PID
= Mod + SIA
VoComm
=Off
Program Digicom
Channels ?
cpx 020.qxd 09/08/2006 16:31 Page 91

11) Press Yes the display will show:-
You MUST turn On the Triggers you require.
12) Use the Yes & No keys to accept or change
the options on the following screens:-
13) Press Yes. The display will show:- Program Digicom
Channels ?
Set = Off Alrm = Off
UnSet = Off PA = Off
Set = Off Alrm = Off
UnSet = Off PA = Off
24Hr = Off E/E = Off
12Hr = Off Bat = Off
Tamp = Off AC = Off
LF = Off Alert = Off
Fire = Off W/D = Off
Duress = Off
Zone Remove = Off
Alrm - Restore = Off
AC - Restore = Off
LF - Restore = Off
After - Alarm = Off
Abort - Call = Off
Perimeter = Off
PA - Restore = Off
Radio Lost = Off
Radio Jamm = Off
Zone Fault = Off
Zone Mask = Off
cpx 020.qxd 09/08/2006 16:31 Page 92

14) Press 0 (zero) three times. The display will show:-
Linefault Sounders Description
The Linefault Sounder option determines how the system sounders (speakers) will
react when a Linefault is detected. Below are the options available and a description of
each option.
On if Set Linefault Sounders will operate when the system is Set and a
Linefault is detected (may be silenced by User Code).
On if Unset Linefault Sounders will operate when the system is Unset and a
Linefault is detected. (may be silenced by User Code)
FLT if Off A fault tone will be generated when the system is Unset and a
Linefault is detected (may not be silenced by User Code).
Beep if Off A periodic beep will be generated when the system is Unset and a
Linefault is detected (may not be silenced by User Code).
Always On Linefault Sounders are always On (Set or Unset) (may not be
silenced by User Code).
01 Jan 00: 00: 01
cpx 020.qxd 09/08/2006 16:31 Page 93

Engineer Reset
If the system is programmed as Engineer Reset the system will need to be Reset by
the Engineer Code. Please follow the procedure below to effect the Reset.
1) If the system is still set, unset it via a valid User Code.
2) Enter the Engineer Code. The display will show:-
3) Enter a valid User Code. The display will show:-
5) Press Yes. The system will start to Set.
6) Enter the Engineer Code again.
This will Abort the Setting.
7) The System is now Reset.
Details of User Code Reset and Anti-Code Reset are given in the User Manual.
Do you want to . .
Use ENGNR. Mode ?
Do you want to . .
SET the System ?
01 Jan 00: 00: 01
Enter Authorisor
Code . . . . . .
cpx 020.qxd 09/08/2006 16:31 Page 94

Wiring Proximity ‘E’ and ‘I’ Readers
‘I’ Reader Terminals RKP Terminals
Single ‘E’ Reader up to 7.5m
‘E’ Reader Wiring RKP Terminals
Single ‘E’ Reader 7.5m to 15m
‘E’ Reader Wiring RKP Terminals
Details on wiring multiple Readers are provided with the Reader.
ANTSET0VANTSET0V
ANTSET0V
‘E’ReaderWiring
RED
BLUE
YELLOW
BLACK
ANTSET0V
‘E’ReaderWiring
RED
GREEN
YELLOW
BLACK
cpx 020.qxd 09/08/2006 16:31 Page 95

Clearing ‘Test Fail’ Indication
If the display shows:-
The system has a zone On Test that has failed
when the system was Set.
Please note: we recommend that the Test Attribute
is only used on 12Hr type zones.
To clear the display proceed as follows.
1) Enter the Engineer Code. The display will show:-
2) Enter a valid User Code. The display will show:-
4) Press Yes. The system will start to Set.
5) Allow the system to fully Set.
6) Enter the Engineer Code again to Unset the
system. The display will show:-
Unset Test Fail
01 Jan 00: 00: 01
01 Jan 00: 00: 01
Do you want to . .
Use ENGNR. Mode ?
Do you want to . .
SET the System ?
Enter Authorisor
Code . . . . . .
cpx 020.qxd 09/08/2006 16:31 Page 96

Power Input
Max Loop Resistance
Loop Delay Time
FUSES
Mains Supply Fuse
Battery Fuse
Aux Fuse
Keypad Fuse
Battery Fuse - Lead
Low Voltage Output
Battery Sizes
Construction
Complies with
Conforms with
Number of Zones
(Standard)
Expansion Type
Number of Keypads
Zone Descriptors
Max No of Users
Default Codes
Code Length
User Names
230V a/c ±10% @ 50Hz
2K (not with E.O.L.)
400mS
20mm 125mA Anti-Surge
20mm 2A Anti-Surge
20mm 1A Quick Blow
20mm 250mA Quick Blow
20mm 2A Anti-Surge
13.8V dc Regulated
12V 1A2, 2A, 3A, 7A
3mm Polycarbonate
EN50131-1 PD6662 2004
CE tested
EMC Directive 89/336/EEC
& LVD Directive 73/23/EEC
8 (2 Wire), 9(EOL), 8+8 (EOL)
1 Radio Expander may be fitted
4 Normal
16 Characters
(last 3 omitted with tamper)
15 + Engineer
Eng 1234, User 5678
4, 5 or 6 digits
9 Characters
5 SPECIFICATIONS
cpx 020.qxd 09/08/2006 16:31 Page 97

Custom Screen
Maximum Output Current
Log Size
Time & Date
Non-Volatile Memory
Quiescent Currents
Control Panel plus Keypad
32 Characters
1A* (See Power Supply Rating)
250 Event Log
31 Event Modem Log
Log & Display
Yes
150mA@12V d.c
*Power Supply Rating
It should be noted that the eurösec CPX has 1 Amp available for the full system.
However, for the purpose of compliance to EN and PD6662 standard, the capacities of
the power supply have to be specified differently.
For a Grade 2 system you have 72 hours to charge the battery. With the CPX Control
Panel, 90mA is available for battery charging. This defines a theoretical maximum
standby battery capacity of 8.0Ah and a maximum of 666mA available for system
power. If a smaller capacity battery is used then the rating has to be reduced
accordingly. For example: If a 7Ah battery is used it will recharge in 72 Hrs and will
theoretically provide 910mA (1000-90mA) for the system. However, the supply rating
for that system under PD6662 is still 7.0Ah/12hrs = 583mA. Sounders, detectors and
other auxiliary items should be included when calculating current drawn by the system.
Any damage caused through overloading the Control Panel Supply will not be covered
by the warranty
We recommend that additional power supplies are used to supply detectors on long
cable runs.
cpx 020.qxd 09/08/2006 16:31 Page 98

AUX 12V Terminals
This pair of terminals supply the + and - supply for the detectors. 1A is available from
these terminals (see power supply rating above).
Strobe Terminals
This pair of terminals are the output for the Strobe. The negative terminal is switched
during an alarm period. A maximum of 600mA may be drawn from these terminals (see
power supply rating above).
Bell Terminals
This pair of terminals are the output for the Bell or external sounder. The negative
terminal is switched
during an alarm period. A maximum of 1A may be drawn from these terminals
(see power supply rating on previous page).
cpx 020.qxd 09/08/2006 16:31 Page 99

6 4 WIRE CONTOUR RKP WIRING
INFORMATION
Note: All keypads on the same system MUST be of the same type. i.e. All four wire or
all six.
Note: All Keypads MUST be connected before powering up the Control
Panel.
CPXKeypad Connection Details
REMOTEKEYPAD
D2D10V12V
KEYPAD
CONNECTIONS
REMOTE
KEYPAD(S)
MAY BE WIRED
IN STAR OR
DAISYCHAIN
FORMAT
D2/BD1/A0V12V
Note: 680 Ohm resistor should
be fitted to ONE of the RKPs.
If RKPs are wired in daisy chain
this should be the last RKP in
the line,
Remove 2K2
if using Keypad
Zones and use
resistor EOL.
GTAG
PROXIMITY
READER(S)
4 Wire Contour RKP
A1 & A2, if used, are connected
to the first reader (antenna).
If using an second reader, remove
the link and connect between A3 & A4.
680 Ohm
2K2
Note: Both detectors must be run on a single cable
from the Keypad to the first detector
then the second. The 2K2 resistor must be in the
last/final detector.
Zone 12V 0V D1 D2
3K3 2K25K6
1st Detector 2nd Detector
+ Power -Alarm N/C Tamper N/C+ Power -
RKP
0V D1Zone 12V D2
5K6 2K23K3
2nd Detector Door Contact
Alarm N/C Tamper N/C+ Power -
RKP
Alarm
Note: Keypad zones are
preset and cannot be changed.
E/E - 3K3 KP Zone 1
Part E/E - 5K6 KP Zone 2
EOL - 2K2
Keypad Zone Wiring Details
cpx 020.qxd 09/08/2006 16:31 Page 100

Notes
cpx 020.qxd 09/08/2006 16:31 Page 101

Notes
cpx 020.qxd 09/08/2006 16:31 Page 102

RISCO Group UK Ltd
Tel: 0161 655 5500 Fax: 0161 655 5501
Internet: www.riscogroup.com
e-mail: sales@riscogroup.co.uk
Technical Support: 0161 655 5600
Technical Support Fax: 0161 655 5610
RISCO Group UK Ltd reserve the right to amend the software and features without prior notice
PR5649 Rev1.25INEW021PR C
cpx 020.qxd 09/08/2006 16:31 Page 103

Cpx eng manual

More Related Content

Similar to Cpx eng manual (20)

Recently uploaded (20)

Cpx eng manual