Ct05%20 sensors%20tech
- 1. technical hotline +44 (0)1268 563720 white | wiring devices 461 Sensors Technical Simple Fit PIRs Description MK Simple Fit Sensors offer cost effective presence detection for lighting control in small to medium areas. This one-box solution is easy to install and commission, and requires no additional parts. The following versions are available: G Flush mounted K5015 - Spring Clips enable ease of installation in plasterboard ceilings G Surface Mounted K5016 - Screw and Plug Fixings can be mounted direct to the ceiling or on to a square pattress box (K2160 WHI) Features Advanced presence detection by passive infrared (PIR) technology Passive photocell holds lights off when area becomes occupied in bright ambient conditions Off delay in minutes following the last observed movement after which lights switch off Detection pattern and approx range in metres at floor level for 2.5m mounting height (detection pattern is cone shaped). Dimensions K5015 K5016 Technical specification Maximum recommended mounting height: 1.8m to 3m Range: Cone-shaped detection pattern, 5m radius at 2.5m mounting height Operating voltage: AC220~240V/50Hz Recommended circuit protection: 16A Maximum load: 6A or 1500W fluorescent/incadescent lightling load capacity Photocell: Approx. 30~200 Lux Off delay: 5sec - 40min Colour: White Material: Flame retardant PC IP rating: IP20 K5015 Depth required behind ceiling: 100mm Weight: 105g excluding cable K5016 Weight: 105g approx 11 Power requirement AC 220 ~ 240V / 50Hz Lighting load (Max) 6A or 1500W fluorescent/incandescent lighting load capability Detection angle Up to 360° at 25°C at 2.5m Detection range 5m radius at 2.5m mounting height Mounting height Recommended ceiling height 1.8m to 3m Mounting type Flush mount Isolation switch control AUTO/OFF Time adjustment Adjustable 5 seconds ~ 40 minutes Lux adjustment Approx. 30 ~ 200 Lux Warm up time About 1 minute Protection degree IP20 Safety CE Product Dimensions Specification 86mm 76mm 76mm 11 Power requirement AC 220 ~ 240V / 50Hz Lighting load (Max) 6A or 1500W fluorescent/incandescen lighting load capability Detection angle Up to 360° at 25°C at 2.5m Detection range 5m radius at 2.5m mounting height Mounting height Recommended ceiling height 1.8m to 3 Mounting type Flush mount Isolation switch control AUTO/OFF Time adjustment Adjustable 5 seconds ~ 40 minutes Lux adjustment Approx. 30 ~ 200 Lux Warm up time About 1 minute Protection degree IP20 Safety CE Product Dimensions Specification 86mm 86mm 54.5mm K5016K5015 10m 0-40
- 2. wiring devices | white www.mkelectric.co.uk 462 Sensors Technical Standard PIRs Description Standard PIRs are part of a comprehensive range of presence detection systems designed to control any type of lighting load, particularly modular luminaires. They provide simple, cost-effective presence detection for lighting control in small areas. The following versions are available: G Slimline flush K4010 G Surface mounted K4011 Features Advanced presence detection by passive infrared (PIR) technology Passive photocell holds lights off when area becomes occupied in bright ambient conditions Off delay in minutes following the last observed movement after which lights switch off Detection pattern and approx range in metres at floor level for 2.5m mounting height (detection pattern is cone shaped). Hand-held Controllers (K4051 and K4052) provide local user override Dimensions K4010 K4011 Technical specification Maximum recommended mounting height: 3.0m Range: Cone-shaped detection pattern, diameter (at floor level) = 2.4 x mounting height 6.0m 2.5m Operating voltage: 230V 50Hz Recommended circuit protection: 10 Amps Maximum load: 6 Amps resistive or fluorescent Photocell: Adjustable 50-5000 lux Off delay: 20 minutes (fixed) and a 10 second Walk Test Mode (need K4050 or K4053 to put it in a Walk test mode) Colour: White Material: Flame retardant PC/ABS IP rating: K4010: IP4X K4011: IP3X K4010 Depth required behind ceiling: 125mm Weight: Flush – 70g excluding cable Surface – 200g approx K4011 Weight: 200g approx 115mm 65mm 62mm deep 10mm deep 100mm K4011 – surface detectorK4010 – flush detector 6m 20
- 3. technical hotline +44 (0)1268 563720 white | wiring devices 463 Sensors Technical Superior PIRs Features Presence detection is by passive infrared, effectively enhanced to improve sensitivity to small movements Passive photocell holds lights off in bright ambient conditions. Active photocell has the capability to switch lights off in occupied areas Off delay in minutes following the last observed movement after which the lights switch off (1 minute to 96 hours via K4053) 6m Detection pattern and approx range in metres at floor level for 2.5m mounting height (detection pattern is cone shaped). Dual-circuit option (1 x volt-free, 1 x switched-live output: K4017 & K4018 only). Switched-live influenced by photocell, volt-free output by presence detection only. Independent time delays can be programmed via K4050 or K4053 Hand-held Controllers (K4051 and K4052) provide local user override Remote programming via K4050 or K4053 ensures changes can be easily accommodated (Note that not all options are available when using HP10) Washroom mode. If no movement is detected in a 24-hour period, detector can be programmed to switch the load on for the duration of the off delay. With suitable valve unit can be used as urinal control Dimensions K4015 K4016 Technical specification Maximum recommended mounting height: 3.0m Range: Cone-shaped detection pattern, diameter (at floor level) = 2.4 x mounting height 6.0m 2.5m Off delay: 1 minute – 96 hours (5-35 mins via K4050) and 10 second Walk Test Mode. (Off Delay 1 & 2 on K4017 and K4018 are independently adjustable.) Photocell: Adjustable 50-5000 lux Operating voltage: 230V 50Hz Recommended circuit protection: 10 Amps Maximum load: 6 Amps per output (not exceeding 10A in total) only in dual circuit option Colour: White Material: Flame retardant PC/ABS Weight: Flush – 70g excluding cable Surface – 200g approx IP rating: K4015: IP4X K4016: IP3X Description Superior PIRs are part of a comprehensive range of presence detection systems designed to control modular luminaires with high frequency ballasts, and other lighting loads. They offer high-performance, programmable presence detection for lighting control in offices and open-plan workstations. Available in flush and surface mount versions with single or dual circuit options. 115mm 65mm 62mm deep 10mm deep 100mm The housing may be secured to a hard surface or a BESA box. The detector fits into the housing with a simple bayonet action. Brown – Live In Black – Live Out Blue – Neutral Green/Yellow – Earth (no internal connection) Suitable for flush mounting in a suspended ceiling tile, maximum 54mm thick and with a minimum clearance of 125mm between front surface of tile and hard ceiling behind. Cut a 50mm diameter (K4054 plasterboard fixing kit) circular hole in the ceiling tile, feed the flying lead and detector through and secure into position with the locking ring.
- 4. wiring devices | white www.mkelectric.co.uk 464 Sensors Technical Superior PIRs for DSI Features Presence detection is by passive infrared, effectively enhanced to improve sensitivity to small movements Regulating photocell ensures a minimum maintained light level, taking account of the contribution from adjacent luminaires and daylight Incorporates simple scene-setting - up to six scenes can be set via user remote Off delay in minutes following the last observed movement after which the lights switch off (1 minute to 96 hours via K4053) 6m Detection pattern and approx range in metres at floor level for 2.5m mounting height (detection pattern is cone shaped) Hand-held Controllers (K4051 and K4052) provide local user override Remote programming via K4050 or K4053 ensures changes can be easily accommodated OneSwitch™ Dimming. Manual input to adjust light level or turn luminaires on or off Dimensions K4019 K4020 Technical specification Maximum recommended mounting height: 3.0m Range: Cone-shaped detection pattern, diameter (at floor level) = 2.4 x mounting height 6.0m 2.5m Photocell: Regulating Operating voltage: 230V 50Hz Recommended circuit protection: 10 Amps Capacity: K4019 – 9 ballasts K4020 – 25 ballasts Output: Digital DSI Colour: White Material: Flame retardant PC/ABS Weight: Flush – 70g excluding cable Surface – 200g approx IP rating: K4019: IP4X K4020: IP3X Description Superior Self Regulating PIRs offer high performance, programmable presence detection for lighting control for work stations and offices. It is designed to control groups of luminaires by regulating DSI type ballasts. Push-to-Make Mains-Rated Retractive Switch Supply 230V 50Hz OneSwitchTM Input Brown Blue Orange White Red L N Supplied with 3m cable 115mm 65mm 62mm deep 10mm deep 100mm
- 5. technical hotline +44 (0)1268 563720 white | wiring devices 465 Sensors Technical Battenfit Sensors Features Advanced presence detection by passive infrared (PIR) technology Off delay in hours following the last observed movement after which lights switch off. Up to 96 hours with K4053. (K4042, K4043 and K4044 only) Fixed 20 minutes off delay with K4051 Passive photocell holds lights off in bright ambient conditions. Active photocell has the capability to switch lights off in occupied areas (K4042 only) Regulating photocell adjusts luminaire output to maintain constant light levels (K4043 and K4044 only) Detection pattern and range in meters under normal operating conditions One Switch Dimming. Manual input to adjust light level or turn luminaires on or off (K4043 and K4044 only) Hand-held Controllers (K4051 and K4052) provide local user override Infrared programming enables easy commissioning and re-commissioning Dual circuit option (switching or digital dimming) available (K4043 and K4044 only) Scene setting – lights switch on to a pre-programmed scene when area becomes occupied (K4043 and K4044 only) K4041, K4042, K4043, K4044 Technical specification Maximum recommended mounting height: 5.0m Range: Cone-shaped detection pattern, diameter (at floor level) = 2.4 x mounting height 6.0m 2.5m Off delay: 1 minute – 96 hours (5-35 mins via K4050) and 10 second Walk Test Mode. (Off Delay 1 & 2 on K4017 and K4018 are independently adjustable.) Photocell: Adjustable 50-5000 lux Operating voltage: 230V 50Hz Recommended circuit protection: 10 Amps Maximum load: 2A for K4041 and K4042 25 ballast for K4043 and K4044 Colour: White Material: Flame retardant PC/ABS Weight: 100g IP rating: 4X Description A range of simple to fit batten-mounted sensors which can deliver energy savings of up to 50%. The BattenFit sensor is a simple-to-fit control solution for batten style luminaires. 14 M20x1.5M20x1.5 29 14 107 600 40 5-35 R K4041, K4042, K4043, K4044 Detection Profile Plan View o Detection pattern is a 360 o Detection pattern is a 360 o cone shape. Diameter is 2.25 x the mounting height. The squares show the arrangement of the detection pattern. Sensitivity is greater when approaching at a tangent rather than heading towards the centre. Direction of mostDirection of most commonly usedcommonly used entry into detectionentry into detection zone, i.e. start ofzone, i.e. start of corridor or doorwaycorridor or doorway 5m5m 5m5m 2.5m2.5m oo 97 2.5m2.5m DETECTION ZONEDETECTION ZONE 5.6m5.6m BATTEN LUMINAIRE A Dimensions (mm) 5m
- 6. wiring devices | white www.mkelectric.co.uk 466 Sensors Technical Digital Sensors – Ceiling Mounted Features Active presence detection by microwave technology Regulating photocell actively monitors ambient light levels and adjusts the light output accordingly (dimmable control gear only) Incorporates simple scene-setting - up to six scenes can be set via user remote Off delay in minutes following the last observed movement after which the lights switch off (1 minute to 96 hours via K4053) 7m Detection pattern and range in metres under normal operating conditions Dual circuit control. Digital output always influenced by photocell, relay output can be influenced by photocell if configured Hand-held Controllers (K4051 and K4052) provide local user override Remote programming with the K4053 ensures changes can be easily accommodated OneSwitch™ Dimming. Manual input to adjust light level or turn luminaires on or off Dimensions K4025 Technical specification Maximum recommended mounting height: 3.0m Range: Approx 7m dia at 2.4m ceiling height 7.0m 2.4m Off delay: 5-60 minutes – adjustable Photocell: Adjustable 50-5000 lux Operating voltage: 230V 50Hz Recommended circuit protection: 10 Amps Maximum load (VOLT-FREE): 6 Amps Maximum load (DSI): 25 ballasts Colour: White Material: Flame retardant PC/ABS Weight: 300g IP rating: IP3X Description Digital sensors are part of a comprehensive range of presence detection systems designed to control modular luminaires with DSI, high frequency ballasts and other lighting loads. They offer superior-performance programmable presence detection for lighting control in offices and open-plan workstations. They use microwave presence detection technology which enables the range to be adjusted to ensure a tailored detection pattern to suit any application and is available for flush and surface mounting with single or dual-circuit option. 100mm Flange 15mm deep Digital sensors utilise microwave radar to monitor a space for movement. This involves transmitting a very low power microwave signal and examining the reflected signal for frequency variations called “doppler shifts”. The microwave system is extremely sensitive to small body movements and provides effective presence detection in rooms up to 20m x 20m. Please note that this extreme sensitivity makes it essential that the detector be installed on a rigid surface that will not itself be subject to movement or vibration. Please note also that microwave technology is not recommended for applications where there are large areas of metal, e.g. metal ceiling or floor tiles, as unpredictable sensitivity may result.
- 7. technical hotline +44 (0)1268 563720 white | wiring devices 467 Sensors Technical Digital Sensors – Corner Mounted Features Active presence detection by microwave technology Passive photocell holds lights off in bright ambient conditions 0-20 Off delay in minutes following the last observed movement after which the lights switch off 20m Detection pattern and range in metres under normal operating conditions Hand-held Controller (K4051) provide local user override Dimensions K4032K4033 Technical specification Maximum recommended mounting height: 3.5m Range: Adjustable up to 20m Off delay: 10 seconds to 20 minutes Photocell: Adjustable 50-5000 lux Operating voltage: 230V 50Hz Colour: White Material: Flame retardant PC/ABS Weight: 250g IP rating: 43 when ceiling mounted 4X when wall mounted Description Digital corner mounted sensors are high performance, directional presence detector with built-in photocell for use in almost any internal space. It was conceived to bridge the gap between the Standard Series LightSpot and the Long Range equipment. It is ideal for larger classrooms, conference rooms, longer storage aisles etc. It is a self-contained unit, making installation very simple and straightforward. They utilise microwave technology and are capable of effective presence detection in rooms of up to 20m x 20m. The units are self-contained, featuring a movement detector, photocell and 10 Amp (load switching) element in one, easily deployed housing. The detectors may be surface or semi-flush mounted. 74mm 60 mm 95 mm 50.8mm 20mm back entry Rear view Photocell Off Range On Range Delay (Position of controls when commissioning commences) K4032 – Surface version The back-box can be secured directly to a hard surface or to a conduit stop end box. K4033 – Semi-flush version Use a hole saw to drill a 76mm hole into the ceiling tile. The flush ring is designed to clamp the tile between its two halves.
- 8. wiring devices | white www.mkelectric.co.uk 468 Sensors Technical Ultrasonic Sensors Features Active presence detection by ultrasonic technology Passive photocell holds lights off in bright ambient conditions 5-15 Off delay in minutes following the last observed movement after which the lights switch off 13m6m Detection pattern and range in metres under normal operating conditions Dimensions K4031K4030 Technical specification Operating voltage: 230V 50Hz Maximum recommended mounting height: 5 metres Switch capacity: 10 Amps – Incandescent lamps: 1500W max (230V) Terminal capacity: 2 x 1.5mm or 1 x 2.5mm Weight: 148g Time delay: 5, 10 or 15 mins Power-up condition: select ON or OFF Detector range: adjustable On/Off Ranges:: adjustable Ultrasonic frequency: 40kHz Photocell: adjustable 50 to 5000 lux Description Ultrasonic sensors are general purpose, fully automatic, directional presence detectors with photocell. They save energy by switching off lights in unoccupied areas and by holding lights off in occupied areas which have adequate natural light. They use a specially developed ultrasonic radar to monitor the controlled space for movement. This radar is sensitive enough to respond to even very small movements thus ensuring that lights are sustained whenever the controlled space is occupied. If no movement has been detected for a pre-selected period, the sensors switch the lights off until the next visitor is detected. The sensors control feature a movement detector, photocell and 10 Amp load switching element in one easily deployed housing. The technology has been refined and improved over many years of efficient, reliable service in a wide range of industrial and commercial environments. The latest designs use state-of-the-art miniaturisation to pack the features into a small, attractive yet rugged enclosure which gives full field-of-view adjustment. Detectors are available for surface or semi-flush mounting. 71mm 51mm 120mm 60mm 60 mm 83 mm A sensor will fit to its own backplate or to a standard 25mm switch sinking box. Flush Plate & Clamp (K4078) For simple flush mounting of detector to suspended ceilings. Max clamping distance – 25mm 20mm back entry knockout 3 x side entry knockout Rear View Ultrasonic sensors utilise ultrasonic radar to monitor a space for movement. This involves transmitting an ultrasound signal and examining the reflected signal for frequency variations called “doppler shifts”. The transmitted signal is more quickly dissipated in open space and squeezed out by constraining walls and ceilings. The range of the detector also depends upon the type of movement being observed: for example, walking activity can be observed at a greater distance than the slight hand or body movement to be expected from a person working at a desk. Note that detectors can see behind themselves slightly so must be inset in a storage aisle or corridor application. K4030 – Surface version The back-box can be secured directly to a hard surface or to a conduit stop end box. K4030 – Semi Flush version Use a hole saw to drill a 76mm hole into the ceiling tile. The flush ring is designed to clamp the tile between its two halves.
- 9. technical hotline +44 (0)1268 563720 white | wiring devices 469 Sensors Technical Long Range Detectors Description Long Range Detectors are high performance presence detection system for use in almost any internal space. It was conceived to bring effective energy-saving control to large areas such as warehouses, sports halls, workshops, hangars, classrooms etc. The system offers many outstanding features and user options, making it the natural choice for large and prestigious situations. Long Range LightSpot is designed to the highest quality standards and performance criteria to ensure efficient and trouble-free operation in the most exacting locations. Long Range Detectors comprise of 230-volt control units with single or dual volt-free output relays, rated to switch any type of load up to 10 amps. Features Active presence detection by microwave technology Passive photocell holds lights off in bright ambient conditions (Requires K4106). Active photocell has the capability to switch lights off in occupied areas 0-16 0-32 Off delay in minutes following the last observed movement after which the lights switch off 30m Detection pattern and range in metres under normal operating conditions Dual circuit control. Relay 2 (K4040 model only) always influenced by photocell, relay 1 output can be influenced by photocell if configured Dimensions Technical specification CONTROL UNITS (K4039/K4040) Operating voltage: 230v 50 hz Switch: 10 amp x 230v (volt-free) Incandescent lamps: 1500w max (at 230v) Terminals: 1 x 6mm or 2 x 2.5mm Weight: 850g approx Power supply: Transformer isolated 12V Semi-automatic: Using low voltage switch Segregation: None Time-out: 0-16 minutes per channel K4039 - 1channel K4040 - 2channels Power-up condition: Select on or off Photocell: Remote operation Dimensions: 175 x 125 x 75 mm K4036 – SURFACE DETECTOR Voltage: 12V dc Frequency: 10.7GHz low power microwave Weight: 800g approx On/Off Range: Adjustable Construction: Zinc & polycarbonate IP rating: IP4X Max mounting height: 6m Flush fixing (K4035 only): To 2-gang sinking box 125mm 170mm 80mm 145mm 175 mm 120 mm K4036 – surface detector K4035 – flush detector K4036 (K4039/K4040 required) K4035 (K4039/K4040 required)
- 10. wiring devices | white www.mkelectric.co.uk 470 Sensors Technical Universal Photocell Features Regulating photocell ensures a minimum maintained light level, taking account of the contribution from adjacent luminaires and daylight Hand-held Controllers (K4051 and K4052) provide local user override Remote programming via K4050 or K4053 ensures changes can be easily accommodated Incorporates simple scene-setting - up to six scenes can be set via user remote Passing cloud timer – prevents nuisance switching when light levels fluctuate rapidly, can be set from 5-60 minutes Dimensions K4045 Technical specification Operating voltage: 230V 50Hz Power consumption: <10W Volt-free contact: 6 Amps max. Any type of lighting load Ambient temperature range: 0 to +40ºC Ballast control type: Single master; no other masters to be connected Ballast control capacity: 25 Max (1-10V, DSI, DALI Ballasts – ballast type selected via K4053) Photocell sensitivity: 0 to 5000 Lux (with a 20% reflective workplane) Recommended mounting eight: 2.4m 6.0m 2.4m Maximum mounting height: 6.0m Material: Flame Retardant PC/ABS IP rating: IP3X Weight: 350g Description The K4045 is a high performance regulating and switching photocell for DSI, DALI, Analogue 1-10V and non-regulating ballasts. It can be used with all common types of control gear in almost any environment where lights would be left on unnecessarily when there is sufficient daylight. The K4045 observes the controlled space, not just daylight, and takes account of all light contributions. Photocell operation is extremely user-friendly: lights will not be switched on or off until the Passing Cloud Time delay has elapsed thus removing the possibility of nuisance switching. The K4045 offers more advanced features and operational parameters than an ordinary, simple photocell. Consequently, it requires careful and considered commissioning and is aimed at higher specification projects. 115mm 65mm WHITE CABLE: Brown – Live Blue – Neutral Green/Yellow – Earth (no internal connection) Black } Volt-free Output 6A Max Grey BLACK CABLE: Yellow – Dimming Control + ve Green – Dimming Control - ve 5-60
- 11. technical hotline +44 (0)1268 563720 white | wiring devices 471 Sensors Technical Accessories K4050 – Hand-held Programmer K4053 – Digital Programmer K4051 & K4052 – Hand-held Controllers Technical specification Battery type: 6V dc (2 x CR 2032 cells) Typical battery life: 3 years Dimensions: 75 x 58 x 18mm (L x W x D) Weight: 50g Technical specification Battery type: 4.5V dc (3 x AAA alkaline cells) Display: 128 x 64 monochrome dot matrix LCD Dimensions: 150 x 85 x 35mm (L x W x D) Weight: 228g Technical specification Battery type: 3V dc (2 x AAA alkaline cells) Typical battery life: 1 year Dimensions: 120 x 56 x 22mm (L x W x D) Weight: 115g Operating range: 2.5m Description The K4050 is a simple-to-use, low-cost programming tool for use with MK’s range of stand-alone lighting control products. Features Parameters, such as time delay and semi- automatic/fully automatic operation, are chosen via an array of 12 dil switches, the status of which is then programmed into the MK detector. Most programmable parameters are catered for although not all options are available for programming on some products (see K4053 below). Description The K4053 Digital Programmer can be used with all K4050-compatible products; it offers a full range of programmable parameters and also a “Download” facility. K4051 The K4051 provides the same functions as the K4052 along with the ability to set and recall up to six different lighting ‘scenes’. Supplied with wall bracket. See Technical Data Sheets on individual detectors to check compatibility. Specification The K4050 can also be used to set the regulating light level in conjunction with a suitable lux meter on supported products via a simple UP/DOWN/ STORE command. All detectors (except Standard PIRs, Digital Corner Mounted and Long Range) are programmable via the K4050 although not all the programmable parameters are supported by all detectors. Please check individual Technical Data Sheets for details. K4052 This remote control offers the user temporary on/ off override and light level adjustment. Supplied with wall bracket. See Technical Data Sheets on individual detectors to check compatibility. K4050 K4051 K4052 K4053