Dcs 910 a1-manual_v1.10(e)

Table of Contents

Table of Contents
Product Overview....................................................4 Setup > Image Setup................................................. 29
.
Package Contents............................................................... 4 Image Settings..................................................... 29
System Requirements........................................................ 4 Setup > Video............................................................ 30
.
Introduction. ...................................................................... 5
. Video Configuration. ............................................ 30
.
Features. ............................................................................ 6
. Setup > Mail............................................................... 31
Hardware Overview............................................................ 7 Email Account...................................................... 31
Front View.................................................................... 7 Time Schedule...................................................... 32
Rear View. ................................................................... 8
. Setup > FTP............................................................... 33
Hardware Installation......................................................... 9
. FTP Server........................................................... 33
.
Software Installation. ....................................................... 11
. Time Schedule...................................................... 34
Using D-Link Click ‘n Connect. .................................. 11
. Setup > Time and Date............................................... 35
Install Setup Wizard Software.................................... 16 Maintenance > Device Management. ......................... 36
.
Maintenance > Backup and Restore........................... 37
Configuration....................................................... 19
Maintenance > Firmware Upgrade............................. 38
.
Using the Setup Wizard.................................................... 19
Status > System......................................................... 39
Viewing Your Internet Camera.......................................... 22
Configuration. .................................................................. 24
. D-ViewCam Installation. ......................................... 40
.
Live Video.................................................................. 24 Add a Camera................................................................... 43
Setup > Wizard.......................................................... 24
. Using & Configuring the DCS-910. .................................. 48
.
Internet Connection Setup Wizard........................ 25 Router Set-Up and Installation......................................... 51
Network Setup. .................................................... 27
.
Troubleshooting.................................................... 54
Setup > DDNS . ......................................................... 28

D-Link DCS-910 User Manual 2

Table of Contents

Networking Basics................................................. 56
Check your IP address..................................................... 56
.
Statically Assign an IP address........................................ 57
.


Section 1 - Product Overview

PackageOverview
Product Contents
• DCS-910 Internet Camera
• CAT5 Ethernet Cable
• Power Adapter
• Manual, Software and D-Link Click ‘n Connect setup utility on CD
• Quick Install Guide
• Camera Stand

Note: Using a power supply with a different voltage than the one
included with your product will cause damage and void the warranty
for this product.

If any of the above items are missing, please contact your reseller.

System Requirements
• Computer with Windows® Vista or XP
• PC with 1.3GHz or above; at least 128MB RAM
• Internet Explorer 6.0 or Netscape Navigator™ 7.0 and above
• Existing 10/100 Ethernet-based network



Introduction
C o n g r a t u l a t i o n s o n y o u r p u rc h a s e o f t h e D C S - 9 1 0 I n t e r n e t C a m e r a ! T h e D C S - 9 1 0 i s a v e r s a t i l e a n d
unique solution for your small office or home. Unlike a PC Camera, the DCS-910 is a stand-alone system with a
bui lt - i n C P U t hat t rans m it s hi g h qual ity video i mages fo r mon itor i ng. Th e D CS-9 10 can b e r emot el y
accessed, and controlled using a Web browser over the Intranet or Internet. The simple installation procedure and
intuitive Web-based inter face offer easy integration with your Ethernet/Fast Ethernet network.
The DCS-910 also comes with remote monitoring capability for a complete and cost-effective home security solution.



Features
• Simple to Use: The DCS-910 is a stand-alone system with a built-in CPU, requiring no special hardware or software such as
PC frame grabber cards. The DCS-910 supports both ActiveX mode for Internet Explorer and Java mode for Internet Explorer
and Netscape Navigator™.
• Supports a Variety of Platforms: Supporting TCP/IP networking, HTTP, and other Internet related protocols. The DCS-910 can also be
integrated easily into other Internet/Intranet applications because of its standards-based features.
• Ethernet/Fast Ethernet Support: The DCS-910 offers Ethernet/Fast Ethernet connectivity, making the DCS-910 easy to
integrate into your existing network environment.
• Quick and easy setup with D-Link Click ‘n Connect setup utility.
• Web Configuration: Using a standard Web browser, administrators can configure and manage the Internet Camera directly
from its own Web page via Intranet or Internet. This means you can access your DCS-910 anytime, anywhere in the world.
• Remote Monitoring Utility: The D-ViewCam application adds enhanced features and functionalities for the Internet Camera,
and allows administrators to configure and access the Internet Camera from a remote site via Intranet or Internet. Other
features include monitoring images, recording images to a hard drive, viewing up to 32 cameras on one screen, and taking
snapshots.
• Broad Range of Applications: With today’s high-speed Internet services, the Internet Camera can provide the ideal solution
for delivering live video images over the Intranet and Internet for remote monitoring. The Internet Camera allows remote
access using a Web browser for live image viewing, and allows the administrator to manage and control the Internet Camera
anytime, anywhere in the world. Many applications exist, including industrial and public monitoring of homes, offices, banks,
hospitals, child-care centers, and amusement parks.



Hardware Overview
Front View

Camera Lens
Power and Link LED

Camera Stand



Rear View

Reset

Ethernet Connector Power Connector

Camera Stand



Hardware Installation
Attach the Swivel Stand
Locate the stand mount on the back panel of the DCS-910 and screw on the swivel stand to the
DCS-910.

Connect the Ethernet Cable
Connect the included Ethernet cable to the network cable connector located on the bottom panel
of the DCS-910 and attach it to the network. Network Connectivity is confirmed when the green
LED Indicator on the DCS-910, located below the Power LED, is illuminated.



Attach the External Power Supply
Attach the external power supply to the DC power input connector located on the bottom panel
of the DCS-910 and connect it to your local power supply.

Note: Power source is confirmed when the red LED Power Indicator located below the
lens on the DCS-910 is illuminated.

The Internet Camera comes with a camera stand with a swivel ball screw head that can be attached to the Internet Camera back panel
socket cavity. Attach the camera stand to the Internet Camera and station it for your application. There are holes located in the base
of the camera stand allowing the Internet Camera to be mounted to the ceiling, or any wall securely.

Socket for camera stand


Section 2 - Installation

Software Installation
Using D-Link Click ‘n Connect
Turn on the computer and Insert the D-Link DCS-910 Installation CD in the CD-ROM drive. Use the D-Link Click ‘n Connect utility for
initial setup. The following step-by-step instructions will be shown in Windows® XP. The similar steps and screens will be shown
for other Windows operating systems.

Select Language

Click on Start button

If the CD Autorun function does not automatically start on your computer, click Windows Start > Run. In the Run command box type
“D:D-Link.exe”, where D: represents the drive letter of your CD-ROM. If it does start, proceed to the next screen.



On the rear panel of the camera a number, the MAC ID is printed. Write
this number down, it will be needed later. Click Next to continue.

Click Next

If you have not yet connected the Ethernet
cable to the camera, do so now. Connect the
other end of the cable to your computer or
to the LAN. Click Next to continue.

Click Next



If you have not yet connected the power, do so now. Check the LED
on the front of the camera to make sure it is powered on. Click Next
to continue.

The utility will begin to search for the camera. It uses the MAC ID
to identify it.

Click Next

If the camera is successfully located, the MAC ID you wrote down
previously appears in the MAC ID List. If there are multiple MAC
IDs listed, choose the MAC ID for the camera being installed. Click
Next to continue.

Click Next



If your network does not have an active DHCP server, it is necessary to
assign IP settings to the camera. It is necessary to supply LAN IP settings
for the camera. If you have an active DHCP server (such as a broadband
router) the IP settings are automatically configured.

Note: Users that are connecting the camera directly to a DSL modem
and intend to access the camera through the Internet must configure the
device for the type of connection used for the Internet connection. This
type of setup requires the user to configure the camera in one of two
ways, use a PPPoE connection (requires user name and password) or
supply a fixed (Static) IP address assigned by the ISP.

Click Next to continue.

Click Next

If you need to manually assign IP settings for a Fixed IP Address,
enter the information and click Next to continue.

Click Next



Installation of the comera is now completed. To configure advanced option
or to view the video display, click the Advanced Options button. Your default
web browser will launch and be directed to the IP address of the camera.
In the login dialog for the camera’s web-based user interface, type the user
name “admin” leave the password entry blank and click the OK button. See
below for more information on using the camera’s web interface. Click Exit
to quit the D-Link Click ‘n Connect utility.

Click Exit to quit or
ADVANCED Options to
go to the web interface



Install Setup Wizard Software
The DCS-910 includes Setup Wizard software as an alternative to using the D-Link Click ‘n Connect utility for camera setup. Users might also want to install the
Setup Wizard on their system to be able to re-install or install new camaeras in the future.

To install the Setup Wizard software:

Insert the D-Link DCS-910 Driver CD into your CD-ROM drive and double click on the DCS-910 icon representing the CD-ROM drive located in
My Computer.

Click Multicamera Management

Install the Setup Wizard as directed in the menus that appear. Once
the software is installed it can be used to setup other DCS 910
-
cameras.



Click the Next button to proceed with the installation of the Setup Wizard. You will be able to choose
where to put the software on your computer in a menu that appears later.

Click Next

Read the license agreement and click Yes if you agree and want to proceed with installation.

Click Yes



To use the default location on your computer for the Setup Wizard software, click Next. If you prefer
to put the software in a different location than that listed, click the Browse button, select the desired
location and click Next to continue.

Click Next

Click the Finish button to complete the Setup Wizard installation. The computer will need to be
restarted before the Setup Wizard can be used. A menu appears offering the option of restarting now
or later. Upon restarting the Setup Wizard is ready to use.

Click Finish


Section 3 - Configuration

Configuration
This section will show you how to configure your new D-Link Internet camera using the D-Link Setup Wizard SE.

Using the Setup Wizard
After installing the Setup Wizard software and restarting the computer, a new folder appears in Programs containing the Setup
Wizard. To launch the Setup Wizard go to Programs --> D-Link --> Setup Wizard SE and click on the D-Link Setup Wizard SE
icon.

The SecureCam Network menu appears. Your camera’s IP Address will be displayed along with its corresponding MAC Address
here. Click the Wizard button.
Your camera’s IP Address will be displayed
here along with its corresponding MAC
Address.

Click Wizard



Enter the admin ID and password.

Note: The default Admin ID is admin with the password left blank.

Click Next

Select DHCP if you want to obtain a new IP address every time the camera boots up, or
select static IP to use the same IP address at each boot up. If you choose Static IP it will
be necessary to enter an IP Address and Subnet Mask suitable for your local network.
Enter a Default Gateway IP address to access the camera from remote locations or oterh
subnets. Enter DNS IP addresses if needed for remote access accross the Internet.

Click Next



If you need to make any changes, click Back to modify your settings.
Otherwise, click Restart to save and apply your settings.

Click Restart



Viewing Your Internet Camera
Your setup is now completed!
Click Link to launch the Web page of your camera, and view the images
using your Web browser.

Click Link

The Setup Wizard will automatically open your web browser to the IP address of the DCS-910, in this example it is: http://192.198.0.102.
Your DCS-910 may have a different IP Address.

Enter admin as the default username and leave the password blank. Click OK to continue.



The Home screen of your camera can be accessed from the Setup Wizard using the Link button. You may also use your favorite Web
browser, type “http://address” in the address box, where address is the IP address that you have assigned to your camera in the
previous section.

Click ActiveX or Java radio button to view live video.

• Please make sure that you have the latest version of Java application installed on your computer to ensure proper
operation when viewing the video in Java mode. The Java application can be downloaded at no cost from Sun’s web site.
(http://www.java.com)
• When you connect to the home page of your camera, you will be prompted to download ActiveX. If you want to use ActiveX
to view your video images instead of Java, then you must download ActiveX.



Configuration
Live Video
ActiveX: For Windows® Users that do not have Java installed, please choose this option to view video streaming
on the Home page.

Java: For Windows® users that have Java installed, you can also use this for viewing video. Mac users
must choose this mode to view video.

Setup > Wizard
You may choose to configure your network by using the Internet Connection Setup Wizard
that includes step-by-step instructions. Otherwise, you may manually configure your
connection using the Manual Internet Connection Setup.



Internet Connection Setup Wizard
This wizard will guide you through a step-by-step process to configure your
new D-Link Camera and connect the camera to the Internet.
Click Next to proceed.

Click Next

You may configure your camera using
• DHCP Connection (by default), where your DHCP server will automatically
assign dynamic IP to your device.
• Static IP Address, or
• PPPoE connection, where your camera is directly connected to the
Internet through a DSL modem.
* Input the DNS information if you have chosen and assigned a Static IP
Address for your camera.

Click Next



If you have a Dynamic DNS account and would like the camera to update your
IP address automatically, enable DDNS and enter your host information.

Click Next

Enter a name for your camera.
Then, click Next to proceed.

Click Next

Configure the correct time to ensure that all events triggered, captured and
scheduled at the right time.
Then, click Next to proceed.

Click Next

This page displays your configured settings. Click Apply to save and activate
the setting, or Back to change your settings.

Click Apply



Network Setup
In this section, you can configure your network settings.

DHCP: Select this connection if you have a DHCP server running on your network and
would like a dynamic IP address to be updated to your camera automatically.
Static IP Client: You may obtain a static or fixed IP address and other network information from
your network administrator for your camera. A static IP address will ease you
for accessing your camera in the future.
IP Address: The fixed IP address
Subnet Mask: The default value is “255.255.255.0.” Used to determine if the
destination is the same subnet.
Default Gateway: The gateway used to forward frames to destinations in a
different subnet. Invalid gateway settings may cause the failure of transmissions
to a different subnet.
Primary DNS: Primary domain name server that translates names to IP
addresses.
Secondary DNS: Secondary domain name server to backup the Primary DNS.
PPPoE Settings: You may configure a Second HTTP port that will allow you to connect to the
camera via a standard web browser. The port can be set to a number other than
the default TCP ports 80. A corresponding port must be opened on the router.
For example, if the port is changed to 1010, users must type in the web browser
“http://192.168.0.100:1010” instead of “http://192.168.0.100”.

Port Settings: You may configure a Second HTTP port that will allow you to connect to the camera via a standard web browser. The port can be set to a number
other than the default TCP ports 80. A corresponding port must be opened on the router. For example, if the port is changed to 1010, users must
type in the web browser “http://192.168.0.100:1010” instead of “http://192.168.0.100”.

UPnP Settings: Enable this setting to configure your camera as an UPnP device in the network.



Setup > DDNS
In this section, you can configure the DDNS setting for your
camera. DDNS will allow all users to access your camera using
a domain name instead of an IP address.

DDNS: (Dynamic Domain Name Server) will hold a DNS host name and synchronize the public IP address of the modem when it has been modified.
The username and password are required when using the DDNS service.

Enable: Click to enable the DDNS function.

Server Address: Select your Dynamic DNS Server from the pull down menu.

Host Name: Enter the host name of the DDNS server.

User Name: Enter your username or e-mail used to connect to the DDNS.

Password: Enter your password used to connect to the DDNS server.



Setup > Image Setup
In this section, you can configure the image settings for your
camera.

Image Settings
Enable Antiflicker: Check to enable antiflicker.

Flip Image: Vertically rotates the video. If the camera is installed upside down, Flip Image and Mirror should both be checked.

Mirror: Horizontally rotates the video.

Brightness Control: Allows you to adjust the brightness level.

Contrast Control: Allows you to adjust the contrast level.

Saturation Control: Allows you to adjust the saturation level. .



Setup > Video
In this section, you can configure the video settings for your
camera.

Video Configuration
Video Profile: This section allows you to change the Encode Type, Resolution, FPS, and Quality.

Encode Type: The compression format used when viewing your camera.

Resolution: Select the desired video resolution from three formats: 640x480, 320x240, and 160x120. The higher setting can obtain better
quality. However, it will use more resource within your network.

FPS: Select the optimal setting depending on your network status. Please note that the higher setting can obtain better quality. However,
it will use more resource within your network.

Quality: Select the desired image quality from five levels: Highest, High, Medium, Low, and Lowest.

Light Frequency: Select the proper frequency (50Hz or 60Hz) to reduce image flicker.



Setup > Mail
Email Account
In this section, you can configure the email notification settings for your
camera.

SMTP Server This is the domain name or IP address of your external e-mail server.
Address:
Sender e-mail This is the e-mail address of the person sending the camera snapshots.
Address:
Receiver e-mail This is the e-mail address of recipient for the SMTP server.
Address:

User Name: If the SMTP server uses authentication, you must enter your user name
here.

Password: This is the password that you use with your user name to connect to the
SMTP server.



Time Schedule
Enable e-mail Choosing Always will start sending snapshots to the recipient’s e-mail account right away. Choosing Schedule will allow you to schedule when to
image to e-mail start and stop the sending of snapshots to the recipient’s e-mail account.
account:

Interval: The frequency of the snapshot interval can also be configured from 1 to 65535 seconds.

Test E-mail This will send a snapshot to the e-mail account that you have configured in the E-mail section. If you have configured the SMTP account correctly,
Account: you will be able to send a test file to the e-mail account of the recipient.



Setup > FTP
FTP Server
In this section, you can configure a FTP server to receive the images.

Host Address: This is the IP address of the FTP server that you will be connecting to.

Port Number: Default is port 21. If changed, external FTP client program must change the server
connection port accordingly.

User Name: Specifies the user name to access the external FTP server. If you are to upload
snapshots to an FTP server you will need to fill in the Domain name or IP address of
your external FTP server. The following user settings must be correctly configured
for remote access.

Password: Specifies the password to access the external FTP server.

Directory Path: Specifies the destination folder in the external FTP server.

Passive Mode: Enabling passive mode will allow access to an external FTP server if your camera
is behind a router protected by a firewall.



Time Schedule
Enable upload image to Checking this box will enable video upload to the FTP server you have selected.
FTP server:
Always: Selecting this option allows snapshots to be uploaded to your FTP as soon as you click Apply.

Schedule: Selecting this option allows you to configure the times that you want the snapshots to be uploaded to your FTP server.

Video Frequency: User can select in frames per second (1, 2, 3 or auto, in auto this could go to 4). The user can also select how many seconds for each
frame, this is configurable from 1 to 65535 seconds.

Base File Name: This will be the name that precedes the time, for example DCS9102008072116425101.jpg. This means that the camera took a snapshot
in the year 2008, July 21 at 16th hour (4 o’clock), 42 minutes and 51 seconds and it is picture number one.

File: Select Overwrite and there will only be a few images that are constantly refreshed depending on how many snapshots you choose to have
sent. Select Date/Time Suffix and the pictures will be named with a date and time also. An example of this can be seen above under the
Base file name category. Select Sequence Number Suffix up to 1024 and all the pictures will be numbered from 1-1024. The total amount
of pictures can be configured up to 1024 pictures. Picture number 1025 will be 1 again.

Test FTP Server: This will send a snapshot to the FTP server that you have configured in the Upload section. If you have configured the FTP correctly, you
will be able to see a test file in your FTP server.



Setup > Time and Date
In this section, you can configure the settings of the internal system
clocks for your camera.
Test FTP Server: Select the time zone for your region from the pull-down
menu.

Synchronize NTP Server: Network Time Protocol will synchronize your camera with
an Internet time server. Choose the one that is closest to
your camera,

Copy your Computer’s Time Click to synchronize the time information from your PC.
Settings:
Set the Date and Time Select this to set the time manually.
Manually:



Maintenance > Device Management
In this section, you can change the administrator’s password and
configure the server settings for your camera. You can also manage
the user account(s) that access to your camera.



Maintenance > Backup and Restore
In this section, you can save and restore your configuration,
restore the factory settings, and/or restart the camera.



Maintenance > Firmware Upgrade
Your current firmware version and date will be displayed on your
screen. You may go to the D-Link Support Page to check for the latest
firmware versions available.

To upgrade the firmware on your DCS-910, please download and save
the latest firmware version from the D-Link Support Page to your
local hard drive. Locate the file on your local hard drive by using the
Browse button. Then, open the file and click the “Upload” button to
start the firmware upgrade.



Status > System
This section displays all the details information about
your device and network settings.



D-ViewCam Installation
D-ViewCam software is included for the administrator to manage up to 32 D-Link IP cameras remotely. You may now use the software
to configure all the advanced settings for your cameras. D-ViewCam is a comprehensive management tool for IP surveillance.

Insert the CD-ROM into the CD-ROM drive. A menu screen will appear as shown below.

Click D-ViewCam

D-ViewCam provides English, Traditional Chinese and Simplified Chinese language
versions. Select a language version and click OK to continue.

Click OK




Click Next

Click Browse if you would like to choose a specific folder for the installation,
otherwise click Next to continue.

Click Next



Click Next to start the installation.

Note: The D-ViewCam installation process may take several minutes to
complete.

Click Next

Click Finish to complete the installation.

Click Finish



Add a Camera
This section will show you how to start and add a camera to the D-ViewCam system.

To start D-ViewCam, select Start > All Programs > D-Link > D-Link
D-ViewCam.

Enter Admin as the default user name and leave the password blank.
Click/OK to log into the system and access the Add Camera Wizard.



Welcome to the Add Camera Wizard. Use this wizard to add your cameras to the D-ViewCam system.

Note: Use the left or right arrow to navigate the wizard.

Click / Next to continue.

Click Next



Choose which method to add your camera(s). You can choose Auto Discovery
to automatically search for your camera(s), or choose Add Manually to add your
camera(s) via the camera’s IP address. Click Next to continue.

If you choose Auto Discovery, the system will search all available cameras that
are located on the same LAN with same subnet. The system will place all of the
cameras under the default map called My Map. Click Next to continue.

DCS-910-55

If you choose Add Manually, you will need to enter the IP address of the camera(s).



D-ViewCam shows the detected IP camera(s) information. You can choose and schedule the recording for each camera.

• 24/7 Continuous Recording: Continuously recording 24 hours a day, 7 days a week.

• 24/7 Motion Detection Recording: Continuously monitoring but ONLY recording when motion is detected.

• Office Hours Only: Continuously monitoring during office hours (08:00 AM to 06:00 PM) and ONLY recording when motion
is detected.

• Non-Office Hours Only: Continuously monitoring during non-office hours (06:00 PM to 08:00 AM) and ONLY recording when
motion is detected.

Note: Excluding 24/7 Continuous Recording, other schedule recording types can ONLY do recording when motion is
detected.


DCS-910-55 DCS-910



Select Yes to add other camera(s), or select No if you have no additional camera(s)
to be added. Click Next to continue.

The Add Camera wizard is now complete. Click Close to access the D-ViewCam’s main screen.

Your D-ViewCam Installation is Complete!

Note: Please refer to the D-ViewCam user manual for information
about using D-ViewCam.


Section 4 - Security

Using & Configuring the DCS-910
D-Link’s DCS-910 is a versatile and cost effective Internet Camera offering both video and audio monitoring. It can also serve as a
powerful surveillance system in security applications. DCS-910 can be used with any wired router. This section explains how to view
the camera from either the Internet or from inside your internal network.

Materials Needed:
• 1 DCS-910 Internet Camera

• 1 Ethernet Cable

• A router such as the D-Link DI-624 Wireless Router

• Ethernet based PC for system configuration

Setting Up the DCS-910 For Use Behind a Router
Installing a DCS-910 Internet Camera on your network is an easy 4–step procedure:

1 Assign a Local IP Address to Your Internet Camera

2 View the Internet Camera Using Your Internet Explorer Web Browser

3 Access the Router with Your Web Browser

4 Open Virtual Server Ports to Enable Remote Image Viewing

This section is designed to walk you through the setup process for installing your camera behind a router and enable remote video
viewing. For the basic setup of the DCS-910, follow the steps outlined in the Quick Installation Guide.



After you have completed the setup of the DCS-910 outlined in the Quick Installation Guide you will have an operating camera
that has an assigned IP Address. Because you are using a router to share the Internet with one or more PCs, the IP Address
assigned to the Internet Camera will be a local IP Address. This allows viewing within your Local Area Network (LAN) until the
router is configured to allow remote viewing of the camera over the Internet.

1 Assign a Local IP Address to Your Camera
Run the Setup Wizard program from the CD included with the DCS-910. Follow the steps in the Quick Installation Guide to
configure the DCS-910. The camera will be assigned a local IP Address that allows it to be recognized by the router. Write
down this IP Address for future reference.
This is the IP Address assigned to your camera (192.168.0.120 is only an example). You will probably have a different IP Address.



2 View the Internet Camera Using Your Internet Explorer Web Browser
Run your Internet Explorer Web browser. In the address bar, type in the IP Address that was assigned to the Internet Camera by the
Installation Wizard program. The DCS-910 Home Page appears with a window displaying live video from the camera. You are able
to view this screen from any PC running Internet Explorer on your LAN.

Click on the Configuration button on the left side of the display. Scroll to the bottom of the Network Configuration page to display the
ports used by HTTP and Streaming audio and video.

DCS-910



Router Set-Up and Installation
The following steps generally apply to any router that you have on your network. The D-Link DI-624 is used as an example to clarify
the configuration process. Configure the initial settings of the DI-624 by following the steps outlined in the DI-624 Quick Installation
Guide.

3 Access the Router with Your Web Browser
If you have cable or DSL Internet service, you will most likely have a dynamically assigned WAN IP Address. ‘Dynamic’ means that
your router’s WAN IP address can change from time to time depending on your ISP. A dynamic WAN IP Address identifies your router
on the public network and allows it to access the Internet. To find out what your router’s WAN IP Address is, go to the Status menu
on your router and locate the WAN information for your router (as shown on the next page). The WAN IP Address will be listed. This
will be the address that you will need to type in your Web browser to view your camera over the Internet.

Your WAN IP Address will be listed on the router’s
Status > Device Info page.



Note: Because a dynamic WAN IP can change from time to time depending on your ISP, you may want to obtain a
Static IP address from your ISP. A Static IP address is a fixed IP address that will not change over time and will be more
convenient for you to use to access your camera from a remote location. The Static IP Address will also allow you to
access your camera attached to your router over the Internet.

4 Open Virtual Server Ports to Enable Remote Image Viewing
The firewall security features built into the DI-624 router prevent users from accessing the video from the DCS-910 over the Internet.
The router connects to the Internet over a series of numbered ports. The ports normally used by the DCS-910 are blocked from access
over the Internet. Therefore, these ports need to be made accessible over the Internet. This is accomplished using the Virtual Server
function on the DI-624 router. The Virtual Server ports used by the camera must be opened through the router for remote access to
your camera. Virtual Server is accessed by clicking on the Advanced tab of the router screen.

Follow these steps to configure your router’s Virtual Server settings:

1 Click Enabled.

2 Enter a different name for each entry.

3 Enter your camera’s local IP Address (e.g., 192.168.0.120 in the example in step 2) in the Private IP field.

4 Select TCP for HTTP port and both (TCP and UDP) for Audio and Video channel port.

5 If you are using the default camera port settings, enter 80 into the Public and Private Port section, click Apply.

6 Scheduling should be set to Always so that the camera images can be accessed at any time.



Repeat the above steps adding the port 80 to both the Public and Private Port sections. A check mark appearing before the entry
name will indicate that the ports are enabled.

Important: Some ISPs block access to port 80 and other commonly used Internet ports to conserve bandwidth. Check
with your ISP so that you can open the appropriate ports accordingly. If your ISP does not pass traffic on port 80, you
will need to change the port the camera uses from 80 to something else, such as 800. Not all routers are the same, so
refer to your user manual for specific instructions on how to open ports.

Enter valid ports in the Virtual Server section of your router. Please make sure to check the box next to the camera name on the Virtual
Server List to enable your settings.


Section 5 - Troubleshooting

Troubleshooting
1. Why does the Power LED not light up constantly?
The power supply used might be at fault. Confirm that you are using the provided power supply, which is DC 5V, for the Internet
Camera. Also verify that the power supply is well connected, and/or the option to turn off the LED is enabled.
2. Why does the LAN LED not light up properly?
There might be a problem with the network cable. To confirm that the cables are working, PING the address of a known device on
the network. If the cabling is OK and your network is reachable, you should receive a reply similar to the following (…bytes = 32
time = 2 ms).
Another possible problem may be that the network device utilized by the Internet Camera is not functioning properly, such as hubs
or switches. Confirm the power for the devices are well connected and functioning properly, and/or the option to turn off the LED is
enabled.
3. Why does the Internet Camera work locally but not remotely?
This might be caused by the firewall protection. Check the Internet firewall with your system administrator. The firewall may need to
have some settings changed in order for the Internet Camera to be accessible outside your local LAN. For more information, please
refer to the section about installing your camera behind a router.
Make sure that the Internet Camera isn’t conflicting with any Web server you may have running on your network.
The default router setting might be a possible reason. Check that the configuration of the router settings allow the Internet Camera
to be accessed outside your local LAN.
4. Why does a series of broad vertical white lines appear through out the image?
It could be that the CMOS sensor (a square panel situated behind the lens that measures the light signals and changes it into a
digital format so your computer can present it into an image that you are familiar with) has become overloaded when it has been
exposed to bright lights such as direct exposure to sunlight or halogen lights. Reposition the Internet Camera into a more shaded
area immediately as prolonged exposure to bright lights will damage the CMOS sensor.


Section 5 - Troubleshooting

5. Noisy images occur. How can I solve the problem?
The video images might be noisy if the Internet Camera is used in a very low light environment.
6. The images are poor quality, how can I improve the image quality?
Make sure that your computers display properties are set to at least 6-bit color. Using 16 or 256 colors on your computer will produce
dithering artifacts in the image, making the image look as if it is of poor quality.
The configuration on the Internet Camera image display is incorrect. Through the Web Configuration Video section of the Web
management you need to adjust the image related parameters for improved images such as: brightness, contrast, hue and light
frequency. Please refer to the Web Configuration section for detailed information.
7. Why are no images available through the Web browser?
The ActiveX might be disabled. If you are viewing the images from Internet Explorer make sure ActiveX has been enabled in the Internet
Options menu. You may also need to change the security settings on your browser to allow the ActiveX plug-in to be installed.

If you are using Internet Explorer with a version number of lower than 5, then you will need to upgrade your Web browser software
in order to view the streaming video transmitted by the Internet Camera.


Appendix A - Networking Basics

Networking Basics
Check your IP address
After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server
(i.e. wireless router) automatically. To verify your IP address, please follow the steps below.

Click on Start > Run. In the run box type cmd and click OK.

At the prompt, type ipconfig and press Enter.

This will display the IP address, subnet mask, and the
default gateway of your adapter.

If the address is 0.0.0.0, check your adapter installation,
security settings, and the settings on your router. Some
firewall software programs may block a DHCP request
on newly installed adapters.

If you are connecting to a wireless network at a hotspot
(e.g. hotel, coffee shop, airport), please contact an
employee or administrator to verify their wireless network settings.


Appendix A - Networking Basics

Statically Assign an IP address
If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:

Step 1
Windows ® Vista - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage
Network Connections.
Windows XP - Click on Start > Control Panel > Network Connections.

Step 2
Right-click on the Local Area Connection which represents your D-Link network adapter and select Properties.

Step 3
Highlight Internet Protocol (TCP/IP) and click Properties.

Step 4
Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on
your router.

Example: If the router´s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X
where X is a number between 2 and 99. Make sure that the number you choose is not in
use on the network. Set Default Gateway the same as the LAN IP address of your router
(192.168.0.1).

Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary
DNS is not needed or you may enter a DNS server from your ISP.

Step 5
Click OK twice to save your settings.


Dcs 910 a1-manual_v1.10(e)

More Related Content

What's hot (16)

Similar to Dcs 910 a1-manual_v1.10(e) (20)

Dcs 910 a1-manual_v1.10(e)