Ddec pin dat

DDEC FOR MBE900 AND MBE4000
3 HARDWARE AND WIRING
Section Page
3.1 OVERVIEW ............................................................................................. 3-3
3.2 DDEC-ECU – ENGINE-RESIDENT CONTROL UNIT ............................ 3-5
3.3 DDEC-VCU ............................................................................................. 3-17
3.4 WIRES AND WIRING ............................................................................. 3-53
3.5 CONDUIT AND LOOM ............................................................................ 3-67
3.6 TAPE AND TAPING ................................................................................ 3-69
3.7 SENSORS ............................................................................................... 3-71
All information subject to change without notice. (Rev. 9/05) 3-1
7SA825 0509 Copyright © 2005 DETROIT DIESEL CORPORATION

HARDWARE AND WIRING
THIS PAGE INTENTIONALLY LEFT BLANK
3-2 All information subject to change without notice. (Rev. 9/05)

3.1 OVERVIEW
DDEC for MBE 900 and MBE 4000 requires several electronic control units and their harnesses.
The engine control system monitors and determines all values which are required for the operation
of the engine. The engine-resident control unit is the DDEC-ECU (refer to section 3.2).
The vehicle control system monitors the vehicle systems. The vehicle control system broadcasts
all information on the J1587 and J1939 Data Links, where it can be read by minidiag2 The vehicle
control system module is the DDEC-VCU (refer to section 3.3)
The harnesses connect the electronic control units to sensors and switches, injectors, and
miscellaneous application devices like throttle controls, instrument panel gages and lights. This
chapter describes the functionality of the harnesses and the electronic control units.

HARDWARE AND WIRING

3.2 DDEC-ECU – ENGINE-RESIDENT CONTROL UNIT
The DDEC-ECU monitors and determines all values which are required for the operation of
the engine.
The DDEC-ECU (see Figure 3-1 ) is located on the left-hand side of the engine.
Figure 3-1 DDEC-ECU on the Engine
The DDEC-ECU processes the data received from the Vehicle Control Unit (DDEC-VCU)
for engine control management. The data is then compared to the parameters stored in the
DDEC-ECU. From these data, quantity and timing of injection are calculated and the unit pumps
are actuated accordingly through the solenoid valves.
The part numbers for the DDEC-ECU versions in production in NAFTA are listed in Table 3-1.
DDEC-ECU Part Number Software Version
D21 000 446 78 40 Rel. 53 (12/24 V), 4 cylinder
D21 000 446 74 40 Rel. 53 (12/24 V), 6 cylinder
D3 000 446 85 40 Rel. 56 (12/24 V), 4 cylinder
D3 000 446 84 40 Rel. 56 (12/24 V), 6 cylinder
D3.1 001 446 65 40 Rel. 60a (12/24 V), 4 cylinder
D3.1 001 446 64 40 Rel. 60a (12/24 V), 6 cylinder
Table 3-1 DDEC-ECU Part Numbers and Software Versions

HARDWARE AND WIRING
NOTE:
To obtain a replacement DDEC-ECU, all the data given on the DDEC-ECU label are
required.
The DDEC-ECU data label has the 10 digit engine serial number, the engine horse power, and
torque.
3.2.1 ENVIRONMENTAL CONDITIONS
Temperature, atmospheric conditions, and vibration must be considered. The DDEC-ECU is
resistant to all ﬂuids and toxic gases occurring in the engine compartment.
Temperature
The ambient operating temperature range is -40°F to 257°F (-40°C to 125°C).
Vibration
The vibration load for the DDEC-ECU is maximum 3 g at 10 Hz – 1000 Hz with damping
elements.
Water Intrusion
The DDEC-ECU can be exposed to steam cleaning and pressure washing. Care should be taken
not to pressure spray the connectors.

3.2.2 ENGINE HARNESS
The Engine Harness (EH) is factory installed and delivered connected to the engine sensors and
the DDEC-ECU. See Figure 3-2 for the MBE 900 non-EGR engine EH.
Figure 3-2 Typical Off-highway MBE 900 Six.cylinder Engine Harness —
Non-EGR Engine

HARDWARE AND WIRING
See Figure 3-3 for the MBE 900 EGR engine EH and Figure 3-4 for the MBE 4000 EGR engine
EH.
Figure 3-3 Typical On-highway MBE 900 Six-cylinder Engine Harness — EGR
Engine

Figure 3-4 Typical MBE 4000 Engine Harness — EGR Engine
The wiring for the 55–pin EH connector to the DDEC-ECU is listed in Table 3-2 , and Table
3-3 . The side of the connector shown is looking into the pins.

HARDWARE AND WIRING
Wire Color
Pin
900 4000
Signal Type Function Connector
0 N/A N/A Digital Input —
1 Blk/Yel Blk/Yel Sensor Return CMP Sensor (-)
2 Blk/Viol Blk/Viol Sensor Return CKP Sensor (-)
3 Wht/Yel Wht/Yel Sensor Return Engine Coolant Temp Sensor
4 Brn/Grn Brn/Grn Sensor Return Supply Fuel Temp Sensor
5 N/A Grn/Wht Sensor Return
Passive Engine Oil Press
/ Booster / Fan Speed
Sensor Return
6 Brn/Gray Wht/Blk Sensor Supply
Engine Oil Press Sensor
Supply
7 Grn Grn Sensor Supply
Intake Manifold Press
Sensor Supply
8 N/A N/A Frequency Input —
9 Red/Blu Red/Blu Injector Return
Injector Valves Bank 2
(B - D - F - H)
10 Gray/Yel N/A Sensor Return
Active Engine Oil Press
Sensor Alternative Oil
Combination Sensor, each
w/ Speed Sensor
11 N/A Brn/Wht Output Return Proportional Valve - Ground
12 Red/Blk Brn/Red Output Supply
Proportional Valve Bank
(PV 1 - 4)
13 N/A N/A Sensor Supply —
15 Brn/Wht Gray/Yel Sensor Return
Engine Oil Temp Sensor
Return
16 Red/Grn Red/Grn Injector Return
Injector Valve Bank 1
(A - C - E - G)
17 N/A N/A Frequency Input —
18 N/A N/A
High Side Control
Output
Starter
19 Brn/Viol Brn/Viol Frequency Input CKP Sensor (+)
20 Brn/Yel Brn/Yel Frequency Input CMP Sensor (+)
21 Grn/Yel N/A Sensor Return
Intake Manifold Temp
Sensor Return
22 N/A Blk Sensor Return EGR Temp Sensor Return
23 N/A Blu Sensor Return
Intake Manifold Press
Sensor Return
24 N/A Grn/Viol Frequency Input Turbo Speed # 1
Front
Looking into the Pins
Table 3-2 Engine Harness – Pins 0–26

Wire Color
Pin
900 4000
Signal Type Function Connector
27 N/A Brn/Blk High Side Control
Proportional Valve 5 —
Constant Throttle Valve
28 N/A Wht/Viol Analog Input EGR Temp
29 Viol Viol Analog Input Intake Manifold Pressure
31 N/A N/A Analog Input —
32 Grn/Blu Brn/Gray Analog Input Engine Oil Press
33 Wht Wht Analog Input Engine Oil Level
34 Red/Yel Red/Yel Analog Input Engine Coolant Temp
36 Brn/Blu Brn/Blu Analog Input Supply Fuel Temp
37 N/A N/A Injector Output – High Side —
38 Wht/Blu Gray/Yel Injector Output – High Side Injector/Solenoid Valve F
39 Gray/Brn Gray/Brn Analog Input Engine Oil Temp
40 N/A Red/Wht
PWM/Digital Output –
Low Side
Proportional Valve 6
41 Blu/Wht Red
Low Side
Proportional Valve 3 —
Fan Control
42 N/A Blu/Blk Sensor Supply
Supply
43 Blu/Red Blk/Wht
Low Side
44 Gray/Yel Wht/Blu Injector Output – High Side Injector/Solenoid Valve D
45 Gray/Viol Gray/Grn Injector Output – High Side Injector/Solenoid Valve B
46 N/A N/A Injector Output – High Side —
47 Gray/Blu Gray/Viol Injector Output – High Side Injector/Solenoid Valve E
48 Brn Brn Analog Input Intake Manifold Temp
49 Yel Yel Sensor Return
Engine Oil Level Sensor
Return
50 Grn/Wht Yel
Low Side
51 Red/Wht Wht/Red
Low Side
52 Brn/Red — Output Supply
Supply
53 Gray/Grn Gray/Blu Injector Output – High Side Injector/Solenoid Valve C
54 Gray/Blk Gray/Blk Injector Output – High Side Injector/Solenoid Valve A
Front
Looking into the Pins
Table 3-3 Engine Harness – Pins 27–54

HARDWARE AND WIRING
3.2.3 POWER SUPPLY
NOTE:
The DDEC-ECU and DDEC-VCU must be powered from the same battery voltage
source.
The voltage supply and polarity/overload protection for the DDEC-ECU is listed in Table 3-4.
Voltage Version
Voltage Supply
24 V 12 V
Nominal Voltage 22 V ≤ V≤ 30 V 11 V ≤ V≤ 16 V
Low Voltage
8 V ≤ V≤ 22V
Limited Operating Range
6.5V ≤ V≤ 11V
Limited Operating Range
Polarity Protection Continuous polarity of battery (+) and battery (-) will not damage the system
Overload Switch-off V > 32 V V > 32 V
Table 3-4 DDEC-ECU Voltage Supply
The current consumption for the DDEC-ECU is listed in Table 3-5.
Voltage Version
Current Consumption
24 V 12 V
Peak Current Consumption
(without solenoid drivers)
8.0 A, cyclic, depending on engine
rpm and series
12.5 A, cyclic, depending on
engine rpm and series
Current Draw with Ignition Off I < 1 mA I < 1 mA
Table 3-5 DDEC-ECU Current Consumption
The short circuit recognition thresholds for the DDEC-ECU are listed in Table 3-6.
Voltage VersionShort Circuit Recognition
Thresholds 24 V 12 V
Ground Short 20 A 20 A
Starter to Ground with DDEC-ECU
Control
2.5 A 2.5 A
Solenoid Valve to Return Line 32 A 32 A
Proportional Valve Supply to Ground 14 A 14 A
Proportional Valve to Ground* 2 A 2 A
* Open circuit fault greater than 40 kΩ resistance
Table 3-6 DDEC-ECU Short Circuit Recognition Thresholds – Pin 16/12

NOTE:
Although the DDEC-ECU and DDEC-VCU are voltage insensitive, the DDEC-ECU fuel
map is battery volage specific.
NOTE:
Voltage must be specified at time of engine order.
3.2.4 FUSES
A Battery (+) fuse and an ignition circuit fuse must be provided by the vehicle wiring harness.
Blade-type automotive fuses are normally utilized; however, manual or automatic reset circuit
breakers which meet the following requirements are also acceptable. The fuse voltage rating must
be compatible with the DDEC-ECU's maximum voltage of 32 volts.
FIRE
To avoid injury from fire, additional loads should not be
placed on existing circuits. Additional loads may blow the
fuse (or trip the circuit breaker) and cause the circuit to
overheat and burn.
FIRE
To avoid injury from fire, do not replace an existing fuse with
a larger amperage fuse. The increased current may overheat
the wiring, causing the insulation and surrounding materials
to burn.
The ignition fuse current rating must be sized for the loads utilized in each application; however,
a rating of between 5 and 10 amps is usually sufficient.
The Battery (+) fuse must not open during normal operation.
Bussmann ATC-40 and Delphi Packard Electric Systems MaxiFuse 40 amp rated fuses or
equivalent will satisfy these requirements. Acceptable blow times versus current and temperature
derating characteristics are listed in listed in Table 3-7 and listed in Table 3-8.

HARDWARE AND WIRING
% of Rated Fuse Current Minimum Blow Time Maximum Blow Time
100% 100 hours -
135% 1 minute 30 minutes
200% 6 seconds 40 seconds
Table 3-7 Fuse Current and Blow Time
Temperature % of Rated Fuse Current
-40°C 110% max
+25°C 100%
+120°C 80% min
Table 3-8 Fuse Temperature and Current
3.2.5 PROPORTIONAL VALVE CONTROL
The proportional valve control on the DDEC-ECU controls external setting and switching
elements. The output function of the proportional valves is determined by the conﬁguration. The
outputs of the control unit can be conﬁgured as pulse width modulated (PWM) or digital outputs.
The proportional valve control outputs can be enabled or disabled by minidiag2.
The output function of the proportional valves is listed in Table 3-9.
Valve Signal
MBE 900
Non-EGR
Engine
MBE 900 EGR
Engine
MBE 4000
EGR Engine
Low Side
Control Pin
Power Supply
Pin
(Switched V
Bat)
PV1
PWM/Digital
Output
Exhaust Flap Exhaust Flap Wastegate 55/51 55/12
PV2
PWM/Digital
Output
Compression
Brake
EGR Valve EGR Valve 55/50 55/42
PV3
PWM/Digital
Output
Fan 1 Fan 1 Fan 1 55/41 55/12
PV4
PWM/Digital
Output
Fan 2 Fan 2 Fan 2 55/43 55/12
PV5
PWM/Digital
Output
Unused
Compression
Brake
Compression
Brake
55/11 –
Ground
55/27 — High
Side Control
PV6
PWM/Digital
Output
Unused Grid Heater
Turbo Brake or
Exhaust Flap
and EGR Shutoff
Valve
55/40 55/42
Table 3-9 Proportional Valves

3.2.6 CONNECTORS
See Figure 3-5 for the connectors to the DDEC-ECU.
Figure 3-5 DDEC-ECU Connectors

HARDWARE AND WIRING

3.3 DDEC-VCU
The Vehicle Control Unit (DDEC-VCU)/Adaption Module 2 (ADM2) is the interface between the
DDEC-ECU and the vehicle/equipment for engine control and manages other vehicle/equipment
functions. See Figure 3-6.
Figure 3-6 The DDEC-VCU
The OEM is responsible for mounting this part in an enclosed, protected environment. The
mounting bracket is the responsibility of the OEM. There must be maximum physical separation
of the VIH from other vehicle/equipment electrical systems. Other electrical system wires should
ideally be at least three feet away from the VIH and should not be parallel to the VIH. This will
eliminate coupling electromagnetic energy from other systems into the VIH.
NOTE:
The DDEC-VCU should be mounted with the connectors pointing down.

HARDWARE AND WIRING
The ADM2 communicates over the K-line and J1939 Data Links to the equipment (see Figure
3-7).
Figure 3-7 NAFTA Architecture Off-highway
The DDEC-VCU communicates over the J1587 and J1939 Data Links to the vehicle (see Figure
3-8).

Figure 3-8 NAFTA Architecture On-highway
Within the DDEC-VCU, sets of data for speciﬁc applications are stored. These include idle
speed, maximum running speed, and speed limitation. Customer programmable parameters
are also stored here.
The DDEC-VCU receives data from the operator (accelerator pedal position, switches, various
sensors) and other electronic control units (for example, synchronization controllers for more than
one genset, air compressor controls).
From this data, instructions are computed for controlling the engine and transmitted to the
DDEC-ECU via the proprietary data link.
3.3.1 ENVIRONMENTAL CONDITIONS
Temperature, vibration, and water intrusion must be considered.
Temperature
The ambient operating temperature range is –40°F to 185°F (-40°C to 85°C).
Water Intrusion
The DDEC-VCU is not water tight and cannot be subject to water spray. It must be mounted in an
enclosed, protected environment.

HARDWARE AND WIRING
3.3.2 VEHICLE INTERFACE HARNESS DESIGN
The OEM supplied Vehicle Interface harness (VIH) connects the DDEC-VCU to the DDEC-ECU
and other vehicle systems (see Figure 3-9). Refer to Appendix B for a harness schematic.
Figure 3-9 Typical On-highway Vehicle Interface Harness with a DDEC-VCU

The OEM supplied Vehicle Interface Harness (VIH) connects the ADM2 to the DDEC-ECU and
other vehicle/equipment systems (see Figure 3-10).
Figure 3-10 Typical On-highway and Off-highway Vehicle Interface Harness
with an ADM2

HARDWARE AND WIRING
The following criteria are to be used when designing the VIH.
Criteria: VIH Design
The four vehicle connectors are designed to accept 18 AWG wires for all circuits except
power and ground. These circuits should use 14 AWG wire
The conductor must be annealed copper, not aluminum, and must comply with the
industry standard SAE J1128 document.
Color code the wires as shown in the schematics. If the wires used are the same color,
hot stamp the cavity number on the wires.
NOTE:
The Vehicle Speed Sensor (VSS) must be a twisted pair. The twists are a minimum of 12
turns per foot (305 mm) and are required to minimize electromagnetic ﬁeld coupling.
NOTE:
J1939 cable is required for the J1939 datalink wires. Refer to SAE J1939–11 spec
for speciﬁc requirements.
The low speed propriety IES-CAN link between the DDEC-ECU and the DDEC-VCU must be a
twisted shielded cable with 0.75 mm diameter wire (approximately 20 AWG), bundle shielded
with drain wire and 30 twists per meter. The insulation is rated to 105°C. Termination resistors for
the IES-CAN link are located in the DDEC-VCU and DDEC-ECU.
Frequency Input
The DDEC-VCU has one frequency input on the VIH that can accept a variable reluctance sensor.
A typical frequency input functions is the Vehicle Speed Sensor (VSS). Requirements for a
variable reluctance signal interface are listed in Table 3-10. Inputs use 47 kΩ to ground.
Parameter Range
Input Amplitude Range 3 V, 40 V Peak to Peak
Input Frequency Range 1 to 3000 Hz
Table 3-10 Variable Reluctance Signal Interface

Digital Inputs
The DDEC-VCU has 23 digital inputs located on the VIH. These inputs are in low state by
providing a connection to battery ground and placed in high state by providing an open circuit.
Digital Input Requirements:
High State: Battery (+) >Ein
> 7.0 V
Low State: Vin
< 3.0 V
Isink: Capable of sinking 5–20 mA
There is an exception for pin 12/10 and 12/11 of the 12–pin connector.
Digital Input Requirements for Pins 12/10 and 12/11:
High State: Battery (+) >Ein
> 8.2 V
Low State: Vin
< 3.5 V
NOTE:
Use switches that will not oxidize with the passage of time and environmental factors
due to the low source current.

HARDWARE AND WIRING
The digital inputs are listed in Table 3-11.
Connector
Pin
Description Vmax
Vmin
Pull-up
Resistor
Pull-down
Resistor
Input Requirement
12/7 Feature Not Yet Available — — — — —
12/8 OI Engine Hood Switch Vmax
—0 V 2.35 kΩ — Von<3.0 V, Voff>7.0 V
12/9 Conﬁgurable Input Vmax
0 V 2.35 kΩ — Von<3.0 V, Voff>7.0 V
12/10 Conﬁgurable Input Vmax
0 V 7.7 kΩ Von<3.5 V, Voff>8.2 V
12/11 Engine Stop Vmax
0 V 7.7 kΩ Von<3.5 V, Voff>8.2 V
15/1 Transmission Neutral Vmax
0 V 2.35 kΩ — Von<3.0 V, Voff>7.0 V
15/2 Dual Road Speed Axle Vmax
0 V 5 kΩ — Von<3.0 V, Voff>7.0 V
18/2 Clutch Switch Vmax
0 V 5 kΩ — Von<3.0 V, Voff>7.0 V
18/4 Cruise Control Set/Coast Vmax
0 V 5 kΩ — Von<3.0 V, Voff>7.0 V
18/5
Cruise Control
Resume/Accel
Vmax
0 V 5 kΩ — Von<3.0 V, Voff>7.0 V
18/6
Cruise Control On/Off
Switch
Vmax
0 V 5 kΩ — Von<3.0 V, Voff>7.0 V
18/7 Throttle Select Vmax
0 V 5 kΩ — Von<3.0 V, Voff>7.0 V
18/8 Engine Brake Low Vmax
0 V 5 kΩ — Von<3.0 V, Voff>7.0 V
18/9 Engine Brake High Vmax
0 V 5 kΩ — Von<3.0 V, Voff>7.0 V
18/10 Remote PTO Switch Vmax
0 V 5 kΩ — Von<3.0 V, Voff>7.0 V
18/11 Limiter 0 Vmax
0 V 5 kΩ — Von<3.0 V, Voff>7.0 V
18/12 Limiter 1 Vmax
0 V 2.35 kΩ — Von<3.0 V, Voff>7.0 V
18/13
Shutdown Override
Switch
Vmax
0 V 5 kΩ — Von<3.0 V, Voff>7.0 V
18/14
Air Conditioner
(Limiter 2)
Vmax
0 V 2.35 kΩ — Von<3.0 V, Voff>7.0 V
18/15 Fan Override Vmax
0 V 5 kΩ — Von<3.0 V, Voff>7.0 V
18/16 Throttle Inhibit Vmax
0 V 5 kΩ — Von<3.0 V, Voff>7.0 V
21/12 Idle Validation 2 Vmax
0 V — Von<3.0 V, Voff>7.0 V
21/13 Idle Validation 1 Vmax
0 V — Von<3.0 V, Voff>7.0 V
21/15 Service Brake Switch Vmax
0 V 2.35 kΩ — Von<3.0 V, Voff>7.0 V
21/16 Park Brake Switch Vmax
0 V 2.35 kΩ — Von<3.0 V, Voff>7.0 V
Table 3-11 Digital Inputs

Digital Outputs
The digital outputs are listed in Table 3-12.
Pin Description IMax
Vmax
PMax
Lamp Output Type
15/5 Gear Out 1 2 A Vmax
— High-side Driver
15/6
Engine Brake 2,
Exhaust Flap
2 A Vmax
— High-side Relay Driver
15/9 Relay 2 2 A Vmax
— Low-side Relay Driver
15/10
Grid Heater,
Constant Throttle
Valve Alt
1.8 A Vmax
— High-side Relay Driver
15/11 OI Active Lamp 250 mA Vmax
— Low-side Lamp Driver, Short Protected
15/12 OI Alarm 1.3 A Vmax
— Low-side Lamp Driver, Short Protected
18/1
OI Vehicle Power
Shutdown
1.3 A Vmax
— Low-side Relay Driver, Short Protected
21/4 Oil Level Lamp 250 mA Vmax
2 W at 12
V/24 V
Low-side Relay Driver, Short Protected
21/5 Red Stop Lamp 250 mA Vmax
2 W at 12
V/24 V
21/6
Amber Warning
Lamp
150 mA Vmax
2 W at 12
V/24 V
21/7 Wait to Start Lamp 250 mA Vmax
2 W at 12
V/24 V
21/8 Air Filter Lamp 250 mA Vmax
2 W at 12
V/24 V
Table 3-12 Digital Outputs

HARDWARE AND WIRING
Analog Inputs and Outputs
The analog inputs are listed in Table 3-13. The analog outputs are listed in Table 3-14.
Pin Description Vmax
Vmin
Pull-up or Pull-down Resistor
15/7 Coolant Level Sensor 5 V 0 V
440 Ω to 5 V Pull-up (ADM2)
122 kΩ to 5 V Pull-up (DDEC-VCU)
15/8 Air Filter Sensor 5 V 0 V 200 kΩ to 5 V Pull-up
18/18 Remote Throttle Signal 5 V 0 V 200 kΩ to 5 V Pull-up
21/11 Throttle Pedal Signal 5 V 0 V
Williams Pedal Terminal A, 47 kΩ to
Ground Pull-down
Table 3-13 Analog Inputs
Pin Description Type
12/3 Oil Pressure Warning Lamp Low Side Driver
12/4 Coolant Temperature Warning Lamp Low Side Driver
12/5
Conﬁgurable Output for Actual Values:
0 = Output Disabled
1 = Pedal Torque (10%...90%)
2 = Differential torque (limit load control)
3 = Inverse Pedal Torque (90%...10%)
4 = Actual Torque
5 = Actual Load (automatic trans)
6 = Vehicle Speed
7 = Demand Speed
Output
12/6 Engine Speed Gauge Low Side Output
Table 3-14 Analog Outputs on ADM2
Pin Description Type
12/3
Oil Pressure Warning Lamp
Fuel Filter Restriction Sensor
Oil Pressure Gauge
Low Side Driver Output
Analog Input
Analog Output
12/4
Coolant Temperature Warning Lamp
Coolant Temperature Gauge Output
OI Thermostat Input
Low Side Driver Output
Analog Output
Analog Input
12/5
0 = Output Disabled
1 = Pedal Torque (10%...90%)
4 = Actual Torque
6 = Vehicle Speed
7 = Demand Speed
Output
12/6 Engine Speed Gauge Low Side Output
Table 3-15 Analog Inputs/Outputs on DDEC-VCU

Data Links
The Data Links that provide the communication interface are listed in Table 3-16.
Pin Description Comments
15/15 Engine-CAN (Low) ISO/DIS 11992, One Wire Capability
15/14 CAN-HF-Ground 100 nF to Ground
15/13 Engine-CAN (High) ISO/DIS 11992, One Wire Capability
21/17 SAE 1708 (+) —
21/18 SAE 1708 (-) —
21/19 SAE J1939 CAN (High) —
21/20 CAN-HF-Ground 100 nF to ground
21/21 SAE J1939 CAN (Low) —
Table 3-16 Communication Interface Data Links

HARDWARE AND WIRING
3.3.3 VEHICLE INTERFACE HARNESS WIRING
The OEM is responsible for wiring three connectors to the DDEC-VCU and one connector to the
DDEC-ECU. For connector and terminal part numbers, refer to section 3.3.7.
The wiring for the VIH 21–pin connector for the DDEC-VCU is listed in Table 3-17. The power
and communication links are wired through this connector. The side of the connector shown is
looking into the pins.
Pin Signal Type Function Connector
21/1 Input Battery Voltage
21/2 Input Ignition (+12 V)
21/3 Input Battery Ground
21/4 Digital Output – Low Side Oil Level Lamp*
21/5 Digital Output – Low Side Red Stop Lamp*
21/6 Digital Output – Low Side Amber Warning Lamp*
21/7 Digital Output – Low Side Wait to Start Lamp
21/8 Digital Output – Low Side Air Filter Warning Lamp
21/9 Sensor Supply
Throttle Pedal Power Supply
(+5 V supply)
21/10 Digital Input – Normally Open Plug (not used, must be plugged)
21/11 Analog Input Throttle Pedal Signal
21/12
Digital Input — Normally
Closed
Idle Validation 2 (Throttle Active)
21/13 Digital Input — Normally Open Idle Validation 1 (Idle Active)
21/14 Sensor Return
Throttle Pedal, Remote Throttle,
Fuel Restriction, Air Restriction,
Dual Coolant Level
21/15 Digital Input – Normally Closed Service Brake Switch
Front
Looking into the Pins on the Harness
21/16 Digital Input – Normally Open Park Brake Switch
21/17 Data Link J1708 A (+)
21/18 Data Link J1708 B (-)
21/19 Data Link SAE J1939 (+)
21/20 Data Link J1939 Shield
21/21 Data Link SAE J1939 (-)
* If output is active while engine is running, shut down the engine immediately and initiate an error diagnosis.
Table 3-17 DDEC-VCU 21–Pin VIH Connector Pin Assignments

The wiring for the VIH 18–pin connector to the DDEC-VCU is listed in Table 3-18. The side of
the connector shown is looking into the pins.
18/1
Conﬁgurable Low Side
Digital Output
Relay 4 — The conﬁgurable parameters
are:
0 = Kickdown Position
1 = Actual Torque
2 = Vehicle Speed
3 = Engine Speed
4 = Coolant Temp
5 = Pedal Torque
6 = Booster Air Temp
7 = Oil Pressure Warning Lamp
8 = Coolant Temp Warning Lamp
10 = Vehicle Power Shutdown
18/2
Digital Input – Normally
Closed
(open if clutch is pressed)
Clutch Switch 1
18/3 Ground Idle Validation Ground
18/4 Digital Input – Normally Open Cruise Control, Set/Coast
18/5 Digital Input – Normally Open Cruise Control, Res/Accel
18/6 Digital Input – Normally Open Cruise Control, On/Off
18/7 Digital Input – Normally Open Remote Accelerator Select Switch
18/8 Digital Input – Normally Open Engine Brake Low
18/9 Digital Input – Normally Open Engine Brake High
18/10 Digital Input – Normally Open Remote PTO Switch
18/11 Digital Input – Normally Open
Limiter 0
(LIM0)
18/12 Digital Input – Normally Open Second Vehicle Speed Limit (LIM1)
18/13 Digital Input – Normally Open Engine Shutdown Override
18/14 Digital Input – Normally Open Air Condition Status
18/15 Digital Input – Normally Open Fan Override
18/16 Digital Input – Normally Open Throttle Inhibit
18/17 Sensor Supply
RemoteThrottle, Air Restriction, Fuel
Restriction, or Dual Level Coolent Sensor
18/18 Analog Input Remote Throttle Signal
Front
Looking into the Pins on
the Harness

HARDWARE AND WIRING
The wiring for the VIH 15–pin connector to the DDEC-VCU is listed in Table 3-19. The side of
the connector shown is looking into the pins.
15/1
Digital Input – Switch to Ground,
Normally Open, Disables
Engine Start if Closed
Transmission Neutral Switch
15/2
Digital Input – Switch to Ground,
Normally Open, Sets Speed
Ratio if Closed
Dual Speed Axle
15/3 Frequency Input Vehicle Speed Sensor (+)
15/4 Frequency Input Vehicle Speed Sensor (-)
15/5
Conﬁgurable High Side
Digital Output
Gear Out 1, Output for Modulation
Valve
15/6
Digital Output
Add Engine Coolant Level Sensor
Module Signal
15/7 Analog Input Engine Coolant Level Sensor
15/8 Analog Input Air Filter Sensor (MAS)
15/9
Digital Output
Relay 2 – The conﬁgurable parameters
are:
0 = Disabled
2 = Grid Heater (typically ADM2)
5 = AGS2 Backup Lamp
15/10
Digital Output
Grid Heater (typically DDEC-VCU),
Constant Throttle Valve
15/11
Digital Output
are:
9 = Off
10 = OI Active Lamp
15/12
Digital Output
are:
0 = Disabled
1 = Enable Starter Lockout
2 = Reserved
3 = Reserved
4 = OI Alarm
5 = Reserved
15/13 Data Link
MBE Proprietary CAN (+)
(DDEC-ECU)
15/14 Data Link
MBE Proprietary CAN Shield
(DDEC-ECU)
15/15 Data Link MBE Proprietary CAN (-) (DDEC-ECU)
Front
the Harness

The wiring for the VIH 12–pin connector for the DDEC-VCU is listed in Table 3-20.
12/1 Pulse Input Engine Start
12/2 Data Link K-line Diagnosis Interface
12/3
Analog Output – Low
Side (ADM2)
Digital or Analog Input/Output
– Low Side (DDEC-VCU)
Oil Pressure Gauge/Warning Lamp
Fuel Restriction (Analog Input)
12/4
Analog Output – Low
Side (ADM2)
Digital or Analog Input/Output
– Low Side (DDEC-VCU)
Coolant Temperature Gauge/Warning
Lamp
OI Thermostat (Analog Input)
Check Trans Lamp
12/5
Analog Output (ADM2)
Digital or Analog Output
(DDEC-VCU)
0 = Output Disabled
1 = Pedal Torque (10%...90%)
4 = Actual Torque
6 = Vehicle Speed
7 = Demand Speed
10 = Trans Temp Lamp
12/6
Analogl Output – Low Side
Digital or Analog Output –
Low Side (DDEC-VCU)
Engine Speed Gauge
12/7 Digital Input Feature Not Yet Available
12/8 Digital Input OI Hood Tilt Switch
Conﬁgurable Input:
0 = Disabled
1 = ABS
2 = Retarder
3 = Temporary/Alternate Road Speed
Limit (set road speed limit)
4 = Grid Heater Detection
5 = Minimal Torque
6 = PTO Driving
Conﬁgurable Input:
0 = Disabled
1 = ABS
2 = Retarder
3 = Temposet (set roadspeed limit)
4 = Grid Heater Detection
5 = Minimal Torque
6 = PTO Driving
12/11 Digital Input – Normally Open Engine Stop
12/12 Pulse Input Feature Not Yet Available
Front
the Harness

HARDWARE AND WIRING
VIH to DDEC-ECU Connector Wiring
The wiring for the VIH 16–pin to the DDEC-ECU is listed in Table 3-21. The side of the
connector shown is looking into the pins.
16/1 Data Link CAN Interface (High Line)
16/2 Data Link CAN Interface (Low Line)
16/3 Data Link CAN HF Ground
16/4 Data Link CAN HF Ground
16/5 Power Supply Battery Voltage (+)
16/6 Power Supply Battery Voltage (+)
16/7 NC NC
16/8 Digital Input Starter Control Signal
16/9 Ground Battery Ground (-)
16/10 Digital Output
Proportional Valve 1–4
High Side Supply
16/11 Ground Battery Ground (-)
16/12 Digital Output Starter High Side Control
16/13 Digital Data Link
Diagnostic Link K-line
(ISO)
Proportional Valve 3 Low
Side Control
16/15 Ignition Input Ignition
Proportional Valve 4 Low
Side Control
Front
Looking into the Pins on the Harness
Table 3-21 16–Pin Connector to the DDEC-ECU

VIH to EH Connector Wiring
The wiring for the three-pin connector to the Engine Harness required for fan control for the
MBE 4000 is listed in Table 3-22.
Description
Engine Harness 3–pin
Connector
DDEC-ECU 55–pin
Connector
Fan Control —Control , Switch to
Bat- (PV3 and PV4)
3 41and 43
Table 3-22 Engine Harness Connector for Fan — MBE 4000 EGR Engine Only
See Figure 3-11 for an engine brake schematic.
Figure 3-11 MBE 4000 Fan Connections

HARDWARE AND WIRING
The wiring for the three connectors to the Engine Harness required for engine brakes and fan
control for the MBE 900 without an EGR is listed in Table 3-23 . See Figure 3-12 for a schematic
before the EGR is added.
Description
Engine Harness
Connector/Pin
DDEC-ECU 55 Pin
Connector
Fan Control, Switch to Bat- (PV3, PV4) Y70/Pin 1 41
Fan Control Power Y70/ Pin 3 12
Compression Brake Control, Switch to Bat- (PV2) Y49/ pin 1 50
Compression Brake Power Y49/Pin 2 52
Exhaust Flap Control, Switch to Bat- (PV1) Y91/Pin 1 51
Exhaust Flap Power Y91/Pin 2 12
Table 3-23 Engine Harness Connector for MBE 900 Non-EGR Engine
Figure 3-12 MBE 900 Non-EGR VIH to EH Wiring

The wiring for the three connectors to the Engine Harness required for engine brakes and fan
control for the MBE 900 with an EGR is listed in Table 3-24. See Figure 3-13 for a schematic
when the EGR is added.
Description
Engine Harness
Connector/Pin
DDEC-ECU 55
Pin Connector
Fan Control, Switch to Bat- (PV3, PV4) Y70/Pin 1 41
Fan Control Power Y70/ Pin 3 12
Compression Brake Ground Y49/ pin 1 11
Compression Brake Control, Switch to Bat+ (PV5) Y49/Pin 2 27
Exhaust Flap Control, Switch to Bat- (PV1) Y91/Pin 1 51
Exhaust Flap Power Y91/Pin 2 12
Table 3-24 Engine Harness Connector for MBE 900 EGR Engine
Figure 3-13 MBE 900 EGR VIH to EH Wiring

HARDWARE AND WIRING
VIH Power Wiring
The OEM-supplied VIH power wiring (see Figure 3-14) supplies 12 or 24 volts to the ADM2
and DDEC-ECU or 12 volts to the DDEC-VCU. The system must be sourced directly from the
battery. The terminals are designed to accept 14 AWG wire with an insulation diameter of 3.2 mm
minimum and 5.6 mm maximum.
Figure 3-14 Power Wiring

Power and ground must be sourced directly from the battery. An electrically solid connection
to the battery or bus bar is required so the battery can filter electrical noise from the power
lines. Power for other vehicle systems must not be sourced from the VIH power wires. Do not
use chassis ground.
NOTE:
The ground wire must be electrically separate from chassis ground.
NOTE:
Although the DDEC-ECU and ADM2 are voltage insensitive, the DDEC-ECU fuel map is
battery volage specific.
Power and ground bus bars may be used. The bus bar must be connected to the battery posts with
0 AWG or larger wire depending upon the total vehicle current requirement. The connecting wires
must be as short as possible to minimize circuit resistance. Do not connect the ground wire to the
chassis ground. The bus bar and all related DDEC-ECU and DDEC-VCU ground circuity must
not be any part of the chassis ground circuit.
Provide maximum physical separation of the VIH power wiring from other vehicle electrical
systems. Other electrical system wires should ideally be at least three feet away from the VIH
power wiring and should not be parallel to the VIH power wiring. This will eliminate coupling
electromagnetic energy from other systems into the VIH power wiring.
NOTICE:
Connection to reverse polarity will damage the system if not
properly fused.
A 20 amp fuse must be used and installed as close to the battery as possible.
The conductor must be annealed copper not aluminum and must comply with the industry
standard, SAE J1128 JAN 95 Low Tension Primary Cable. Contact the Society of Automotive
Engineers to obtain documents, refer to Appendix for their address.
Splices must be soldered and sealed with a waterproof insulator. Alpha FIT-300, Raychem
TAT-125 or any equivalent heat shrink - dual wall epoxy encapsulating adhesive polyolefin is
required.
Detroit Diesel Corporation recommends color coding. Alternatively, wires may be hot stamped
with the cavity number.
The DDEC-VCU will log a high voltage code (PID 168, FMI 0) when the battery voltage is
greater than 19 V for a 12 V system and 36 V for a 24 V system.
The DDEC-VCU will log a low voltage code (PID 168 FMI 1) when the battery voltage is less
than 10 V for a 12 V sustem and 16 V for a 24 V system.

HARDWARE AND WIRING
Communications – SAE J1939 Data Link
SAE J1939 Data Link+, SAE J1939 Data Link-, and SAE J1939 Data Link Shield are used as the
J1939 communication link. J1939 cable is required for the J1939 data link. Termination resistors
are required per the SAE speciﬁcation. Refer to SAE J1939–11 for speciﬁc requirements.
NOTICE:
The communication system operation will degenerate if the wrong
cable is used.
The DDEC-VCU connector pin assignments for SAE J1939 are listed in Table 3-25.
Pin Signal Type Function
21/19 Data Link SAE J1939 (+)
21/20 Data Link J1939 Shield
21/21 Data Link SAE J1939 (-)
Table 3-25 J1939 DDEC-VCU to VIH Connector Pin Assignments
The following SAE documents cover the SAE J1939 Data Link. Contact the Society of
Automotive Engineers to obtain documents, refer to Appendix C for their address.
SAE J1939 Top Layer (Overview)
SAE J1939/11 Physical Layer
SAE J1939/21 Data Link Layer
SAE J1939/71 Vehicle Application Layer
SAE J1939/01 Truck and Bus Applications
SAE J1939/73 Application Layer — Diagnostics
J1939 cable is available from the following sources:
Belden Electronics Division Tyco Electronics Corporation
2200 U.S. 27 South Raychem Wire & Harnessing
Richmond, IN 47374 300 Constitution Drive
Phone: 1–800–235–3361 Menlo Park, CA 94025
www.belden.com www.raychem.com
For a list of supported messages, refer to section 6, "Communications Protocols."

Communications – Proprietary IES-CAN Data Link
The low speed proprietary IES-CAN link between the DDEC-ECU and the DDEC-VCU must be
a twisted shielded cable with 0.75 mm diameter wire (approximately 20 AWG), bundle shielded
with drain wire and 30 twists per meter. The insulation is rated to 105°C. Termination resistors
for the IES-CAN link are located in the DDEC-VCU and DDEC-ECU. The wiring for the
DDEC-ECU 16–pin connector and the DDEC-VCU 15–pin connector are listed in Table 3-26.
DDEC-VCU 15–Pin Function DDEC-ECU 16–Pin
15/13 IES-CAN Data Link (+) 16/1
15/15 IES-CAN Data Link (-) 16/3
15/14 IES-CAN Data Link (Shield) 16/2
Table 3-26 Propriety IES-CAN Data Link
3.3.4 POWER SUPPLY – 12 VOLT SYSTEM
Normal operating voltage on a 12 V system for the DDEC-VCU and DDEC-ECU is 11-16 VDC.
NOTICE:
Operating the DDEC-VCU or DDEC-ECU over the voltage limits
of 32volts will cause damage to the DDEC-VCU or DDEC-ECU.
Operating the DDEC-VCU and/or DDEC-ECU between 8 and 11 volts may result in degraded
engine operation. (Transient operation in this range during engine starting is considered normal
for 12 volt systems.)
NOTICE:
Reversing polarity will cause damage to the DDEC-VCU and/or
DDEC-ECU if the Power Harness is not properly fused.
NOTE:
All output loads, ignition and DDEC-VCU power must be powered from the same battery
voltage source.

HARDWARE AND WIRING
Average Current Draw
The maximum average current draw is listed in Table 3-27. This information should be used
to size the alternator.
Maximum Average Current Draw
(12 V Nominal Supply)System
Idle Full Load/Rated Speed
DDEC-ECU – Engine Loads 1–2 A total 12.5 A total
DDEC-VCU – Vehicle Loads* 350 mA total 5.4 A total
* Vehicle loads are controlled by the OEMs who can best determine the total maximum current draw for
their installation.
Table 3-27 Maximum Average Current Draw
The current draw for a DDEC-VCU/DDEC-ECU configuration is listed in Table 3-28.
Configuration Condition Current
Ignition Off 300 µA
DDEC-VCU
Ignition On and Engine Stopped 175 mA
Table 3-28 Current Draw for DDEC-VCU Configuration
The current draw for a DDEC-ECU is listed in Table 3-29.
Ignition Off 1 mA
DDEC-ECU
Table 3-29 Current Draw for DDEC-ECU Configuration
Battery Isolator
DDEC for MBE 900 and MBE 4000 does not require a battery isolator. However, some
applications require a battery that is dedicated to the engine and completely isolated from the rest
of the vehicle. Commercially available battery isolators can be used.

Main Power Shutdown
The main power supply shutdown schematic shows the DDC approved method for main power
switch implementation. See Figure 3-15.
Figure 3-15 Main Power Supply Shutdown 12 Systems
NOTE:
Switches must remain closed for 30 seconds after ignition is off for the DDEC-ECU
and DDEC-VCU to write non-volatile data.
NOTE:
Disconnecting positive power is not sufﬁcient to isolate the DDEC-VCU for welding
purposes.
NOTE:
It is recommended that both the positive (+) and negative (-) battery leads be
disconnected.

HARDWARE AND WIRING
NOTICE:
When welding, the following must be done to avoid damage to the
electronic controls or the engine:
□ Both the positive (+) and negative (-) battery leads must be
disconnected before welding.
□ The welding ground wire must be in close proximity to
welding location - the engine must never be used as a
grounding point.
□ Welding on the engine or engine mounted components is
NEVER recommended.
NOTE:
The alternator should be connected directly to the battery for isolation purposes.
3.3.5 POWER SUPPLY – 24 VOLT SYSTEM
Normal operating voltage for the DDEC-VCU and DDEC-ECU is 16-32 VDC.
NOTICE:
Operating the DDEC-VCU or DDEC-ECU over the voltage limits
of 32 volts will cause damage to the DDEC-VCU or DDEC-ECU.
Operating the DDEC-VCU and/or DDEC-ECU between 8 and 16 volts may result in degraded
engine operation. (Transient operation in this range during engine starting is considered normal
for 24 volt systems.)
NOTICE:
Reversing polarity will cause damage to the DDEC-VCU and/or
DDEC-ECU if the Power Harness is not properly fused.
NOTE:
All output loads, ignition, DDEC-ECU, and ADM2 power must be powered from the same
battery voltage source.

Average Current Draw
The maximum average current draw is listed in Table 3-30. This information should be used
to size the alternator.
Maximum Average Current Draw
(24 V Nominal Supply)System
Idle Full Load/Rated Speed
DDEC-ECU – Engine Loads 1–2 A total 12.5 A total
DDEC-VCU – Vehicle Loads* 350 mA total 5.4 A total
* Vehicle/Equipment loads are controlled by the OEMs who can best determine the total maximum current
draw for their installation.
Table 3-30 Maximum Average Current Draw
The current draw for a DDEC-VCU/DDEC-ECU configuration is listed in listed in Table 3-31.
Ignition Off 300 µA
DDEC-VCU
Table 3-31 Current Draw for DDEC-VCU Configuration
The current draw for a DDEC-ECU is listed in Table 3-32.
Ignition Off 1 mA
DDEC-ECU
Table 3-32 Current Draw for DDEC-ECU Configuration
Battery Isolator
DDEC for MBE 900 and MBE 4000 does not require a battery isolator. However, some
applications require a battery that is dedicated to the engine and completely isolated from the rest
of the vehicle. Commercially available battery isolators can be used.

HARDWARE AND WIRING
Main Power Shutdown
The main power supply shutdown schematic shows the DDC approved method for main power
switch implementation. See Figure 3-16.
Figure 3-16 Main Power Supply Shutdown
NOTE:
Switches must remain closed for 30 seconds after ignition is off for the DDEC-ECU
and DDEC-VCU to write non-volatile data.
NOTE:
It is recommended that both the positive (+) and negative (-) battery leads be
disconnected.

NOTE:
Disconnecting positive power is not sufﬁcient to isolate the DDEC-VCU for welding
purposes.
NOTICE:
When welding, the following must be done to avoid damage to the
electronic controls or the engine:
□ Both the positive (+) and negative (-) battery leads must be
disconnected before welding.
□ The welding ground wire must be in close proximity to
welding location - the engine must never be used as a
grounding point.
□ Welding on the engine or engine mounted components is
NEVER recommended.
NOTE:
The alternator should be connected directly to the battery for isolation purposes.
3.3.6 FUSES
A Battery (+) fuse and an ignition circuit fuse must be provided by the vehicle wiring harness.
Blade-type automotive fuses are normally utilized; however, manual or automatic reset circuit
breakers which meet the following requirements are also acceptable. The fuse voltage rating must
be compatible with the DDEC-VCU – DDEC-ECU's maximum operating voltage of 32 volts.
FIRE
To avoid injury from ﬁre, additional loads should not be
placed on existing circuits. Additional loads may blow the
fuse (or trip the circuit breaker) and cause the circuit to
overheat and burn.

HARDWARE AND WIRING
FIRE
To avoid injury from ﬁre, do not replace an existing fuse with
a larger amperage fuse. The increased current may overheat
the wiring, causing the insulation and surrounding materials
to burn.
The ignition fuse current rating must be sized for the loads utilized in each application; however,
a rating of between 5 and 10 amps is usually sufﬁcient.
The Battery (+) fuse current rating must satisfy two criteria:
□ Must not open during normal operation
□ Must open before the DDEC-ECU or DDEC-VCU is damaged during a reverse battery
condition
Bussmann ATC-20 and Delphi Packard Electric Systems MaxiFuse 20 amp rated fuses or
equivalent will satisfy these requirements. Acceptable blow times versus current and temperature
derating characteristics are listed in Table 3-33 and Table 3-34.
% of Rated Fuse Current Minimum Blow Time Maximum Blow Time
100% 100 hours -
135% 1 minutes 30 minute
200% 6 seconds 40 seconds
Table 3-33 Fuse Current and Blow Time
Temperature % of Rated Fuse Current
-40°C 110% max
+25°C 100%
+120°C 80% min
Table 3-34 Fuse Temperature and Current

3.3.7 CONNECTORS
There are four connectors to the DDEC-VCU, a 21–pin connector, an 18–pin connector, a
15–pin connector, and a 12–pin connector. The OEM is responsible for the four connectors at
the DDEC-VCU and the 16–pin connector at the DDEC-ECU.
NOTE:
The DDEC-VCU connectors are not water tight and cannot be subject to water spray.
The part numbers for the DDEC-VCU 21–pin connector are listed in Table 3-35.
Part Tyco Part Number DDC Part Number
DDEC-VCU 21–pin connector 1–967625–1 013 545 65 26
Terminal (Vehicle) 0.5–1.0 mm wire 927779–6 013 545 76 26
Terminal (Power) 1.5–2.5 mm wire 927777–6 013 545 78 26
Seals — 1.0 mm wire — 000 545 28 39
Seals — 1.5 — 2.5 mm wire — 000 545 29 39
Plug — 000 545 62 80
Lock 1–967634–1 —
Table 3-35 DDEC-VCU 21–pin Connector Part Numbers
Part Tyco DDC Part Number
DDEC-VCU 18–pin connector 1–967624–1 013 545 64 26
Terminal (Vehicle) 0.5–1.0 mm wire — 013 545 76 26
Terminal (Power) 1.5–2.5 mm wire — 013 545 78 26
Seals — 1.0 mm wire — 000 545 28 39
Seals — 1.5 — 2.5 mm wire — 000 545 29 39
Plug — 000 545 62 80
Lock 1–967634–1 —

HARDWARE AND WIRING
Part DDC Part Number
DDEC-VCU 15–pin connector 013 545 63 26
Terminal (Vehicle) 0.5–1.0 mm wire 013 545 76 26
Terminal (Power) 1.5–2.5 mm wire 013 545 78 26
Seals — 1.0 mm wire 000 545 28 39
Seals — 1.5 — 2.5 mm wire 000 545 29 39
Plug 000 545 62 80
DDEC-VCU 12-pin connector 013 545 62 26
Terminal (Vehicle) 0.5-1.0 mm wire 013 545 76 26
Terminal (Power) 1.5-2.5 mm wire 013 545 78 26
Seals – 1.0 mm wire 000 545 28 39
Seals – 1.5 – 2.5 mm wire 000 545 29 39
Plug 000 545 62 80
The part numbers for the DDEC-VCU-to-DDEC-ECU connector is listed in Table 3-39.
DDEC-ECU 16–pin connector 000 153 00 22
Terminal (DDEC-VCU) 0.5–1.0 mm wire 011 545 76 26
Terminal (power) 1.0–2.5 mm wire 011 545 78 26
Seals — 1.0 mm 000 545 28 39
Seals — 1.5–2.5 mm 000 545 29 39
Plug 000 545 62 80
Cover 000 153 00 82
Table 3-39 DDEC-VCU–to–DDEC-ECU 16–pin Connector Part Numbers

SAE J1939/J1587 Six-pin Data Link Connector
The components listed in Table 3-40 are required to incorporate a SAE J1708/J1587 Data Link in
a VIH so a DDR or other diagnostic devices can be attached without a unique jumper.
Component DDC Part Number Deutsch Part Number
Six-pin Deutsch Connector 23513052 HD-10-6-12P
Connector Cover 23513054 HDC-16-6
Two (2) Cavity Plugs 23507136 114017
Four (4) Terminals 23513053 0460-220-1231
Table 3-40 Required Components to Incorporate an SAE J1939/J1587 Data Link
in the VIH
The following illustration shows the wiring for the 6-pin connector (see Figure 3-17).
Figure 3-17 Wiring for Six-pin Data Link Connector

HARDWARE AND WIRING
SAE J1939/J1587 Nine-pin Data Link Connector (Recommended)
The SAE J1708/J1587 nine-pin data link connector is the recommended data link connector. DDC
recommends that the OEM-supplied data link connector be conveniently positioned in a well
protected location facilitating subsequent DDDL usage (i.e., reprogramming, diagnostics, etc.).
The components listed in Table 3-41 are required to incorporate a SAE J1939/J1587 Data Link in
a VIH for diagnostic and reprogramming devices.
Component DDC Part Number Deutsch Part Number
Nine-pin Deutsch Connector 23529496 HD10-9-1939P
Connector Cover 23529497 HDC 16–9
Two (2) Cavity Plugs 23507136 114017
Seven (7) Terminals 23507132 0460-202-16141
Table 3-41 Required Components to Incorporate an SAE J1939/J1587 Data Link
in the VIH
The following illustration shows the wiring for the nine-pin connector (see Figure 3-18).
Figure 3-18 Wiring for 9-pin Data Link Connector
The SAE J1587/J1708 Data Link must be twisted pairs. The twists are a minimum of 12 turns per
foot (305 mm). The maximum length for the SAE J1587/J1708 Data Link is 130 ft (40 m).

3.3.8 GRID HEATER
The grid heater (see Figure 3-19) is driven by a load relay switched to supply voltage. The
installation of a fused high current, as well as the recommended monitoring of the load contact of
the load relay, is the responsibility of the vehicle manufacturer. A sticking load contact of the
load relay can be monitored via input 12/10, but there is no automatic power cut off. If a sticking
load contact occurs, the grid heater control lamp will ﬂash and the grid heater load circuit must
be switched off manually.
Figure 3-19 Grid Heater
Nominal power and resistance for the 12 V and 24 V grid heaters are listed in Table 3-42.
Data 12 Volt 24 Volts
Nominal Power at 1000°C (1832°F) 1.9 KW ± 10% 1.9 KW ± 10%
Resistance at Rated Temperature 62 mΩ ± 10% 250 mΩ ± 10%
Table 3-42 Nominal Power and Resistance
NOTE:
The grid heater requires a 250 Amp relay for 12 V systems, a 120 Amp for 24 V systems.

HARDWARE AND WIRING
Wiring the Grid Heater
The output (21/7) activates the grid heater control lamp. The output (15/9 - ADM2) (15/10 –
DDEC-VCU) activates the load relay for the grid heater. The digital input (12/10) can be used
for monitoring the load contacts of the load relay. If the output is shut off, the relay is switched
to the supply voltage or switched to ground. See Figure 3-20
Figure 3-20 DDEC-VCU Grid Heater Wiring

3.4 WIRES AND WIRING
Detroit Diesel Corporation recommends color coding and hot stamping wire numbers in
contrasting colors at intervals of four inches or less.
3.4.1 GENERAL REQUIREMENTS
NOTE:
Avoid renumbering DDC circuits since all troubleshooting guides reference the circuit
numbers shown in the schematic. DDC suggests including a prefix or suffix with the
DDC circuit numbers when conflicts exist.
3.4.2 GENERAL WIRE
All wires used in conjunction with the DDEC for MBE 900 and MBE 4000 must meet the
following criteria:
NOTICE:
DDC does not recommend using any type of terminal lubricant
or grease compounds. These products may cause dirt or other
harmful substances to be retained in the connector. DDC has not
tested these products and cannot stand behind their use.
NOTICE:
Insulation must be free of nicks.
Criteria: Wires
Tape, conduit, loom or a combination thereof must be used to protect the wires.
Refer to sections 3.5 and 3.6.
All wires must be annealed copper wire (not aluminum).
All wires must comply with SAE J1128.
All wires must be insulated with cross-link polyethylene (XLPE) such as GXL,
or any self-extinguishing insulation having a minimum rating of -40°C (-40°F)
to 125°C (257°F).

HARDWARE AND WIRING
3.4.3 CRIMP TOOLS
The part numbers for the crimp tools for working with the DDEC-ECU and DDEC-VCU
connectors are listed in Table 3-43.
Description Tyco/Amp Part Number
Extraction Tool 726503–1
Hand Crimp Tool 169400–0
Crimp Dies for 0.5 mm – 1.0 mm Terminals 734262–0
Crimp Dies for 1.0 mm – 2.5 mm Terminals 169917–0
Table 3-43 Crimp Tools
3.4.4 DEUTSCH TERMINAL INSTALLATION AND REMOVAL
The method of terminal installation and removal varies. The following sections cover Deutsch
terminal installation and removal.
Deutsch Terminal Installation Guidelines
Deutsch connectors have cable seals molded into the connector. These connectors are push-to-seat
connectors with cylindrical terminals. The diagnostic connector terminals are gold plated for
clarity.
NOTICE:
Improper selection and use of crimp tools have varying adverse
effects on crimp geometry and effectiveness. Proper installation
of terminals require specialized tools. Do not attempt to use
alternative tools.
The crimp tool to use in Deutsch terminal installation is J 34182 (Kent-Moore part number).
NOTICE:
Terminal crimps must be made with the Deutsch crimp tool P/N:
HDT-48-00 to assure gas tight connections.
NOTICE:
If a separate seal is required, be sure to install the seal onto the
wire before stripping the insulation.

Use the following instructions for installing Deutsch terminals:
1. Strip approximately .25 inch (6 mm) of insulation from the cable.
2. Remove the lock clip, raise the wire gage selector, and rotate the knob to the number
matching the gage wire that is being used.
3. Lower the selector and insert the lock clip.
4. Position the contact so that the crimp barrel is 1/32 of an inch above the four indenters.
See Figure 3-21. Crimp the cable.
Figure 3-21 Setting Wire Gage Selector and Positioning the Contact
5. Grasp the contact approximately one inch behind the contact crimp barrel. Hold the
connector with the rear grommet facing you. See Figure 3-22.
Figure 3-22 Pushing Contact Into Grommet

HARDWARE AND WIRING
6. Push the contact into the grommet until a positive stop is felt. See Figure 3-22. A slight
tug will conﬁrm that it is properly locked into place. See Figure 3-23.
Figure 3-23 Locking Terminal Into Connector
Deutsch Terminal Removal
The appropriate size removal tool should be used when removing cables from connectors. The
proper removal tools are listed in Table 3-44.
Tool Kent-Moore Part Number
Removing (12 AWG) J 37451
Removing (16-18 AWG) J 34513-1
Table 3-44 Removal Tools for Deutsch Terminals
Remove Deutsch terminals as follows:
1. With the rear insert toward you, snap the appropriate size remover tool over the cable of
contact to be removed. See Figure 3-24.

Figure 3-24 Removal Tool Position
2. Slide the tool along the cable into the insert cavity until it engages and resistance is felt.
Do not twist or insert tool at an angle. See Figure 3-25.
Figure 3-25 Removal Tool Insertion
3. Pull contact cable assembly out of the connector. Keep reverse tension on the cable and
forward tension on the tool.

HARDWARE AND WIRING
3.4.5 SPLICING GUIDELINES
The following are guidelines which may be used for splices. The selection of crimpers and
splice connectors is optional. Select a high quality crimper equivalent to the Kent-Moore tool, J
38706, and commercially available splice clips.
The recommended technique for splicing and repairing circuits (other than power and ignition
circuits) is a clipped and soldered splice. Alternatively, any method that produces a high quality,
tight (mechanically and electronically sound) splice with durable insulation is considered to
be acceptable.
Clipped and Soldered Splicing Method
The tools required are listed in Table 3-45.
Tool Part Number
Heat Gun --
Sn 60 solder with rosin core ﬂux --
Wire Stripper Kent-Moore J 35615 or equivalent
Splice Clips (commercially available) Wire size dependent
Heat Shrink Tubing Raychem HTAT or equivalent
Table 3-45 Recommended Splicing Tools
Criteria: Splicing Straight Leads
No more than one strand in a 16 strand wire may be cut or missing.
Use Sn 60 solder with rosin core ﬂux.
The exposed wire must be clean before the splice is soldered.

Soldering splice connectors is optional. To solder splice connectors:
1. Position the leads, so one overlaps the other. See Figure 3-26.
Figure 3-26 Positioning the Leads
2. Secure the leads with a commercially available clip and hand tool. See Figure 3-27.
Figure 3-27 Securing the Leads With a Clip
3. Use a suitable electronic soldering iron to heat the wires. Apply the solder to the heated
wire and clip (not to the soldering iron) allowing sufﬁcient solder ﬂow into the splice joint.
4. Pull on wire to assure crimping and soldering integrity. The criteria listed in Table 3-46
must be met.

HARDWARE AND WIRING
Wire Gage Must Withstand Applied Load
14 AWG 45 lb (200 N)
16 AWG 27 lb (120 N)
18 AWG 20 lb (90 N)
Table 3-46 Applied Load Criteria for Terminals
5. Loop the lead back over the spliced joint and tape. See Figure 3-28.
Figure 3-28 Recommended Strain Relief of Spliced Joint
Splicing and Repairing Straight Leads-Alternate Method 1
The tools required are listed in Table 3-47.
Tool Part Number
Heat Gun --
Terminal Crimper for Metri-Pack 280 (12 AWG) Kent-Moore J 38125-6
Terminal Crimper for Metri-Pack 280 (18 AWG) Kent-Moore J 39848
Terminal Crimper for Weather Pack Kent-Moore J 35606
Terminal Crimper for Deutsch Kent-Moore J 34182
Terminal Crimper for Metri-Pack 150 Kent-Moore J 35123

The recommended method to splice straight leads follows:
1. Locate broken wire.
2. Remove insulation as required; be sure exposed wire is clean and not corroded.
3. Insert one wire into the splice clip until it butts against the clip. Stop and crimp (see
Figure 3-29, A).
4. Insert the other wire into the splice clip until it butts against the clip stop (see Figure
3-29, B).
NOTICE:
Any terminal that is cracked or ruptured is unacceptable as
malfunctions may occur.
5. Visually inspect the splice clip for cracks, rupture, or other crimping damage. Remove and
replace damaged clips before proceeding.
6. Pull on wire to ensure the splice integrity. The criteria listed in Table 3-48 must be met.
Wire Gage Must Withstand Applied Load
14 AWG 45 lb (200 N)
16 AWG 27 lb (120 N)
18 AWG 20 lb (90 N)
Table 3-48 Applied Load Criteria for Terminals
7. Shrink the splice clip insulative casing with a heat gun to seal the splice (see Figure
3-29, C).
NOTICE:
Splices may not be closer than 12 in. (.3 m) apart to avoid
degradation in circuit performance. Replace wire to avoid having
splices closer than 12 in. (.3 m) apart.

HARDWARE AND WIRING
Figure 3-29 Splicing Straight Leads - Alternate Method 1

Splicing and Repairing Straight Leads - Alternate Method 2
This method is not allowed or recommended for power or ignition circuits. The tools required are
listed in Table 3-49.
Tool Part Number
Heat Gun --
Terminal Crimper for Metri-Pack 280 (12 AWG) Kent-Moore J 38125-6
Terminal Crimper for Metri-Pack 280 (18 AWG) Kent-Moore J 39848
Terminal Crimper for Weather Pack Kent-Moore J 35606
Terminal Crimper for Deutsch Kent-Moore J 34182
Terminal Crimper for Metri-Pack 150 Kent-Moore J 35123
An acceptable option for splicing straight leads is:
1. Locate broken wire.
2. Remove insulation as required; be sure exposed wire is clean and not corroded.
3. Slide a sleeve of glue lined, shrink tubing (Raychem HTAT or equivalent) long enough to
cover the splice clip on the wire and overlap the wire insulation, about .25 in. (6 mm) on
both sides (see Figure 3-30, A).
4. Insert one wire into splice clip until it butts against the splice clip. Stop and crimp (see
Figure 3-30, B).
5. Insert the remaining wires into the splice clip one at a time until each butts against the
splice clip; stop and crimp (see Figure 3-30, B).
NOTICE:
Any terminal that is cracked or ruptured is unacceptable as
malfunctions may occur.
6. Visually inspect the terminal for cracks, rupture, or other crimping damage. Remove and
replace damaged terminal before proceeding.
7. Slide the shrink tubing over the crimped splice clip (see Figure 3-30, C).
8. Shrink tubing with a heat gun to seal the splice (see Figure 3-30, D).

HARDWARE AND WIRING
NOTICE:
A minimum of two layers of heat shrink tubing must be applied to
splices that have more than one lead in or out.
Figure 3-30 Splicing Straight Leads - Alternate Method 2

Shrink Wrap
Shrink wrap is required when splicing non insulated connections. Raychem HTAT or any
equivalent heat shrink dual wall epoxy encapsulating adhesive polyoleﬁn is required. Shrink wrap
must extend at least .25 in. (6 mm) over wire insulation past splice in both directions.
Alpha Wire Corporation Tyco Electronics Corporation
711 Lidgerwood Ave Raychem Cable Identiﬁcation and Protection
P.O. Box 711 300 Constitution Drive
Elizabeth, New Jersey 07207-0711 Menlo Park, CA 94025
1-800-52ALPHA Phone: 1–800–926–2425
www.alphawire.com www.raychem.com
To heat shrink wrap a splice:
NOTICE:
The heat shrink wrap must overlap the wire insulation about .25
in. (6 mm) on both sides of the splice.
1. Select the correct diameter to allow a tight wrap when heated.
2. Heat the shrink wrap with a heat gun; do not concentrate the heat in one location, but
apply the heat over the entire length of shrink wrap until the joint is complete.
3. Repeat step 2 to apply a second layer of protection (if required by splicing guidelines).

HARDWARE AND WIRING
Staggering Wire Splices
Position spliced wires properly as follows:
NOTICE:
You must stagger positions to prevent a large bulge in the harness
and to prevent the wires from chaﬁng against each other.
1. Stagger the position of each splice (see Figure 3-31) so there is at least a 2.5 in. (65
mm) separation between splices.
Figure 3-31 The Correct and Incorrect Method of Staggering Multiple Splices
NOTICE:
A minimum of two layers of heat shrink tubing extending .25 in. (6
mm) past the splice must be used to complete the splice.
2. Heat shrink a minimum of two layers of heat shrink tubing.
3. Tape the spliced wires to each other. Refer to section 3.5.

3.5 CONDUIT AND LOOM
Conduit must be used to protect the harness cable and cable splices.
NOTICE:
The conduit must not cover any connectors, switches, relays,
fuses, or sensors.
The following guidelines should be used when designing a harness:
NOTICE:
Wires should be sized and cut to near equal length prior to
installing conduit.
□ The distance between the back of the connector or other listed devices to the end of the
conduit should not exceed:
□ 1.0 in. (25 mm) for a single connector/device
□ 3 in. (75 mm) for multiple connectors/devices
□ All cable breakouts and conduit ends must be secured in place with conduit outlet rings or
tape.
Criteria: Conduit and Loom
Due to the wide variety of operating conditions and environments, it is the responsibility
of the OEM to select a conduit that will survive the conditions of the speciﬁc
applications. Flame retardant convoluted polypropylene conduit or equivalent may be
used for most installations. Heat retardant nylon conduit or oil, water, acid, ﬁre, and
abrasion resistant non-metallic loom conforming to SAE J562A*
is also acceptable. The
diameter of conduit should be selected based on the number of wires being protected.
* If non-metallic loom is used, secure the ends with tightly wrapped nylon straps to prevent
unraveling.
Conduit should cover the wires without binding and without being excessively large.

HARDWARE AND WIRING

3.6 TAPE AND TAPING
Tape must be used when conduit is utilized. Be sure to follow the tape manufacturers' guidelines.
The harness manufacturer may use tape under the harness covering (conduit or loom) to facilitate
harness building. Tape must be tightly wrapped at all conduit interconnections with a minimum of
two layers (refer to section 3.5). Be sure to firmly secure the start and finish ends of tape.
Criteria: Tape
NOTICE:
Black vinyl electrical tape should not be used in applications
where the temperature exceeds 176°F (80°C).
In applications where the temperature doesn't exceed 176°F (80°C), black vinyl
electrical tape that is flame retardant and weather resistant may be used.
In applications where temperature exceeds 176°F (80°C), vinyl electrical tape should
not be used. For these applications, adhesive cloth backed, flame retardant polyethylene
or fiber glass tape (Delphi #PM-2203, Polikan #165 or equivalent) is recommended.
Criteria: Taping
The tape must extend a minimum of 1 in. (25 mm) past the conduit.
The tape must be crossed over butted conduit ends.
The tape must be extended a minimum of 1 in. (25 mm) in each direction at all branches.

HARDWARE AND WIRING

3.7 SENSORS
DDEC for MBE 900 and MBE 4000 is designed to operate with several types of sensors as
listed in Table 3-50.
Sensor Type Description
Variable Reluctance/Magnetic Pick-up
Used to monitor the crankshaft position, engine speed, turbo
speed (MBE 4000 only), and vehicle speed.
Thermistor Used to monitor temperatures.
Variable Capacitance Used to monitor manifold, and oil gallery pressures.
Variable Resistance (Potentiometer) Used to sense throttle position.
Switch Used to signal coolant level, inlet air restriction, and oil level.
Table 3-50 Sensor Types
The sensors integrated into the Engine Harness are factory-installed (refer to section 3.7.1). The
sensors integrated into the Vehicle Interface Harness are installed by the OEM (refer to section
3.7.2).
3.7.1 FACTORY-INSTALLED SENSORS
The sensors integrated into the factory-installed Engine Harness are listed in Table 3-51.
Sensor Function
Camshaft Position Sensor (CMP Sensor) Indicates a speciﬁc cylinder in the ﬁring order.
Crankshaft Position Sensor
(CKP Sensor)
Senses crankshaft position and engine speed for functions such
as fuel control strategy.
Engine Coolant Temperature Sensor
(ECT Sensor)
Senses coolant temperature for functions such as engine
protection, fan control and engine fueling.
EGR Temperature Sensor
Senses EGR exhaust temperature after EGR cooler. Used for
EGR system diagnosis.
Engine Oil Pressure Sensor
(EOP Sensor)
Senses gallery oil pressure for functions such as engine protection.
Engine Oil Temperature Sensor
(EOT Sensor)
Senses oil temperature for functions such as reducing variation
in fuel injection and fan control.
Intake Manifold Pressure Sensor
(IMP Sensor)
Senses turbo boost for functions such as smoke control and engine
protection.
Intake Manifold Temperature Sensor
(IMT Sensor)
Senses boost temperature
Supply Fuel Temperature Sensor
(SFT Sensor)
Senses fuel temperature for functions such as engine fueling.
Turbo Speed Sensor
(MBE 4000 only)
Monitors turbo speed.
Table 3-51 Function of Factory-installed Sensors

HARDWARE AND WIRING
See Figure 3-32 for sensor locations on the MBE 900 EGR engine
1. EGR Temperature Sensor 6. Crankshaft Position Sensor (on timing case)
2. Engine Coolant Temperature Sensor 7. Intake Manifold Pressure/Temperature Sensor
3. Supply Fuel Temperature Sensor 8. Engine Oil Temperature Sensor
4. Barometric Pressure Sensor (integrated into
DDEC-ECU)
9. Engine Oil Pressure Sensor
5. Camshaft Position Sensor
Figure 3-32 Sensor Locations on the MBE 900 EGR Engine
NOTE:
The 6–cylinder engine is shown; sensor locations are similar on the 4–cylinder engine.

See Figure 3-33 for sensor locations on the MBE 900 non-EGR engine.
1. Engine Oil Pressure/Temperature Sensor 5. Barometric Pressure Sensor (integrated into
DDEC-ECU)
2. Engine Coolant Temperature Sensor 6. Camshaft Position Sensor (on camshaft)
3. Intake Manifold Pressure/Temperature Sensor 7. Crankshaft Position Sensor (on timing case)
4. Supply Fuel Temperature Sensor
Figure 3-33 Sensor Location on the MBE 900 Non-EGR Engine
NOTE:
The 6–cylinder engine is shown; sensor locations are similar on the 4–cylinder engine.

HARDWARE AND WIRING
Two sensors are not easily visible from the left-hand side of the MBE 4000 engine. The Intake
Manifold Pressure/Temperature Sensor is located on the right-hand side of the charge air
manifold, behind the #2 cylinder head. The Engine Oil Pressure/Temperature Sensor is located at
the base of the oil ﬁlter. See Figure 3-34 for sensor locations on the MBE 4000 engine.
NOTE:
The Engine Oil Level Sensor, if used, is located at the bottom of the oil pan.
1. Intake Air Pressure/Temperature Sensor 5. Engine Coolant Temperature Sensor
2. EGR Temperature Sensor 6. Barometric Pressure Sensor (integrated into
DDEC-ECU)
3. Camshaft Position Sensor (on camshaft) 7. Supply Fuel Temperature Sensor
4. Crankshaft Position Sensor 8. Engine Oil Pressure/Temperature Sensor
Figure 3-34 Sensor Location on the MBE 4000 EGR Engine

3.7.2 OEM-INSTALLED SENSORS
All sensors must be of the proper type and continuously monitor vehicular and environmental
conditions, so the DDEC-ECU can react to changing situations.
The OEM is responsible for installing the sensors listed in Table 3-52.
Sensor Part Number Function
Engine Coolant Level Sensor
(ECL Sensor)
23526905
23526906
23526907
Senses coolant level for engine protection.
Refer to section 3.7.3.
Vehicle Speed Sensor (VSS) —
Senses vehicle speed for Cruise Control and
Vehicle Speed Limiting. Refer to section 3.7.4.
* Available in some applications
Table 3-52 Function and Guidelines for OEM-installed Sensors
NOTE:
The OEM harness must be securely fastened every 6 in. It is required that the harness
be fastened within 6 in. of the sensor.

HARDWARE AND WIRING
3.7.3 ENGINE COOLANT LEVEL SENSOR
The ECL Sensor provides an input to the engine protection system and warn the operator if a
low coolant level has been reached.
The main component of the ECL Sensor consists of a conductivity probe, which connects to
the DDEC-VCU (see Figure 3-35).
NOTICE:
The probe has an operational temperature range of -40 to 257°F
(-40 to 125°C). Exposure to temperatures beyond this range
may result in unacceptable component life, or degraded sensor
accuracy.
Figure 3-35 Engine Coolant Level Sensor Speciﬁcations — DDEC-VCU Only
The connector listed in Table 3-53 is a Metri-Pack 280 series push-to-seat connector.
Coolant Level Sensor Connector
Connector P/N: 15300027
Terminal P/N: 12077411
Seal P/N: 12015323
Secondary Lock P/N: 15300014
Table 3-53 Metri-Pack 280 Connectors and Part Numbers

The OEM must connect the ECL Sensor probe as shown in the next illustration (see Figure 3-36).
Polarity of the ground and signal must be correct for proper operation.
Figure 3-36 Engine Coolant Level Sensor Installation

HARDWARE AND WIRING
The probe should be located in either the radiator top tank or a remote mounted surge tank. It
should be mounted horizontally in the center of the tank and must be in a position to signal low
coolant before aeration occurs. Typically, this is a height representing 98% of the drawdown
quantity. The probe should be located so that it is not splashed by deaeration line, stand pipe or
coolant return line ﬂows. The insulated portion of the probe should be inserted into the coolant
1/2 in. or more past the inside wall of the tank. See Figure 3-37.
Figure 3-37 Engine Coolant Level Sensor Location - Top of Radiator Tank
Determine proper location for low coolant level sensor while running the drawdown test. It must
actuate a warning before the satisfactory drawdown level is reached.
The ECL Sensor components are OEM supplied hardware and can be purchased as kits or
individual components, depending on OEM requirements.

The following kits listed in Table 3-54 and Table 3-55 provide all the necessary hardware for
proper installation of the ECL Sensor. Kits are available through the DDC parts distribution
network.
Component Part Number
ECL Sensor 23526905
Metri-Pack Connector Kit 15300027
Metri-Pack Terminals 12077411
Secondary Lock 15300014
wire Seal 12015323
Terminal 12103881
Table 3-54 ECL Sensor Installation Kit 1/4 in. NPTF P/N: 23515397
Component Part Number
ECL Sensor 23526906
Metri-Pack Connector Kit 15300027
Metri-Pack Terminals 12077411
Secondary Lock 15300014
wire Seal 12015323
Terminal 12103881
Table 3-55 ECL Sensor Installation Kit 3/8 in. NPTF P/N: 23515398
The sensor must be enabled with VEPS, the minidiag2, or the DRS as listed in Table 3-56.
Parameter Range Default Parameter ID
Enable ECL Sensor Input
0 = Disabled
1 = Single Level Sensor
1 1 13 01
Table 3-56 Enabling the Engine Coolant Level Sensor

HARDWARE AND WIRING
3.7.4 VEHICLE SPEED SENSOR
The DDEC-VCU can calculate vehicle speed providing that it is properly programmed and
interfaced with a Vehicle Speed Sensor (VSS) that meets MBE requirements. The VSS (see
Figure 3-38) provides a vehicle speed signal for use in Cruise Control and Vehicle Speed Limiting.
The VSS signal type can be changed with the VEPS, or minidiag2.
NOTE:
DDC does not approve of the use of signal generator sensors.
Figure 3-38 Vehicle Speed Sensor
To obtain accurate vehicle mileage, the parameters listed in Table 3-57 must be programmed with
VEPS, the minidiag2, DRS, DDDL, and the Nexiq DDR.
Parameter Range Default
Parameter
ID
VSS Input Conﬁguration
0 = No Sensor
2 = Magnetic Pickup*
3 = VSS via J1939
2 = Magnetic 1 08 01
Axle Ratio 1 – 20.0 5.29 1 08 03
Number of Output Shaft Teeth 0 – 250 16 1 08 04
Tire Revs/Kilometer 160 – 1599 312 1 08 05
Top Gear Ratio 0.1 – 2.55 1 1 08 06
Gear Ratio Tolerance 0 – 60 2 1 08 08
Second Highest Gear Ratio 0.1 – 2.55 1 1 08 07
Two Speed Axle – Second
Axle Ratio
1 – 20.0 5.29 1 08 09
Anti-tamper
0 = Disable
1 = Enable
0 = Disable 1 08 10
* Range must be set to 2.
Table 3-57 Vehicle Speed Sensor Parameters

Magnetic Pickup
The magnetic pickup requirements are listed in Table 3-58. Magnetic Pickup size is determined
by installation requirements.
Parameters Range
Frequency Range 1 - 3000 Hz
Low Threshold Voltage >1.7 Volts Peak to Peak
DC Resistance 800–3000 Ω
Table 3-58 Magnetic Pickup Vehicle Speed Sensor Requirements
The Vehicle Speed Sensor is wired to the 15–pin connector of the DDEC-VCU as listed in Table
3-59.
Connector/Pin Function
15/3 VSS (+)
15/4 VSS (-)
Table 3-59 Vehicle Speed Sensor Wiring
Magnetic Vehicle Speed Sensors can be obtained from the following sources:
Wabash Technologies Airpax Instruments
Invensys Electro
Corporation
1375 Swan Street Phillips Technologies 1845 57th Street
Huntington, Indiana
46750-0829
150 Knotter Drive Sarasota, Florida 34231
Tel: 260-356-8300 Chesire, Connecticut 06410 Tel: 1–800–446–5762
www.wabashtech.com Tel: 800-643-0643
Fax: 941-355-3120
www.electrocorp.com

HARDWARE AND WIRING
See Figure 3-39 for the installation of the Magnetic VSS.
Figure 3-39 Magnetic Vehicle Speed Sensor Installation

SAE J1939 Data Link
A VSS wired to the DDEC-VCU is not required if the transmission output shaft speed message
is being transmitted over the SAE J1939 Data Link. To obtain accurate vehicle mileage, the
parameters listed in Table 3-60 must be programmed with VEPS or the minidiag2.
Parameter Range Default Parameter ID
VSS Input Conﬁguration
0 = No Sensor
2 = Magnetic Pickup*
3 = VSS via J1939
2 = Magnetic 1 08 01
Axle Ratio 1 – 20.0 5.29 1 08 03
Tire Revs/Kilometer 160 – 1599 312 1 08 05
Top Gear Ratio 0.1 – 2.55 1 1 08 06
Second Highest Gear Ratio 0 — 5.75 2.55 1 08 07
Two Speed Axle — Second Axle Ratio 1 – 20.0 5.29 1 08 09
Anti-tamper
0 = Disable
1 = Enable
0 = Disable 1 08 10
* Parameter must be set to 3 = Transmission output shaft speed on the SAE J1939 Data Link.
Table 3-60 Vehicle Speed Sensor Parameters for Transmission Output Shaft
Speed
VSS Anti-tamper
If the sensor appears to be working improperly, but the vehicle speed is not zero, VSS Anti-Tamper
will log a VSS fault. Refer to section 5.24 for more information on VSS Anti-tamper.

HARDWARE AND WIRING

Ddec pin dat

More Related Content

What's hot (20)

Similar to Ddec pin dat (20)

Recently uploaded (20)

Ddec pin dat