Design and development of pyrolysis batch reactor and characterization of tire pyrolysis oil using gc ms and ft ir

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 11 | Nov-2014, Available @ http://www.ijret.org 366
DESIGN AND DEVELOPMENT OF PYROLYSIS BATCH REACTOR
AND CHARACTERIZATION OF TIRE PYROLYSIS OIL USING GC/MS
AND FT IR
Hariram.V1
, Mohammed Ismail M.A2
1
Department of Automobile Engineering, Hindustan Institute of Technology & Science, Hindustan University,
Chennai, Tamil Nadu, India
2
Department of Automobile Engineering, Hindustan Institute of Technology & Science, Hindustan University,
Chennai, Tamil Nadu, India
Abstract
Owing to the increased fuel crises and rapid growth of transportation sector, it is very much necessary to identify and alternative
to petroleum feed stocks. On the other hand disposal of solid waste material raises the hazard of environmental pollution. In order
to bridge these gaps, a pyrolysis batch reactor was designed and fabricated in the present investigation with an overall dimension
of 400 X 200 X 458 cm and handling capacity of 10 kgs per cycle. The yield of TPO was optimized with reaction temperature to
produce high quantity of gaseous outputs. Elemental analysis, Gas chromatography Mass spectrometry analysis and Fourier
transform infrared analysis were carried out and found that limonene was the major compound in the TPO. The FT IR analysis
also revealed the presence of aliphatic and aromatic compounds in the TPO. The physio-chemical properties of TPO were
determined using Indian standard 1448 standards and were found to usable in internal combustion engine as treated TPO and
blends of TPO with straight diesel.
Keywords: Pyrolysis, Elemental analysis, Limonene, Calorific value, Sulphur.
-------------------------------------------------------------------***-------------------------------------------------------------------
1. INTRODUCTION
The transportation sector faces a major crisis and huge
shortage of petroleum-diesel for its application. It is very
much necessary for the researchers to find an alternative
way for the fuel to be used effectively in internal
combustion engines. With similar or better maneuverability
and efficiencies on comparison with diesel on the other
hand, disposal of solid waste material causes air, water and
soil pollution to a great extent which may be due to higher
population density and increased industries in many
developing countries. Therefore, it is necessary to bridge the
gap between solid waste management and fuel for internal
combustion engine. It was estimated that many developing
and developed countries generate nearly 32 tons of unusable
tires every year which was due to enhanced development in
the transportation sector. An automobile tire contains non-
biodegradable combination of many rubber, metal strips &
cords, carbon black and other inorganic and organic
materials. It is extremely difficult to dispose the above
combinations of material without causing environmental
hazards. There are many methods illustrated for solid waste
disposal such as retreading, oxidizing, hydrogenation and
high temperature pyrolysis. Generally pyrolysis refers to
decomposition of inorganic and organic material at elevated
temperature between 350o
C to 750o
C in the absence of
oxygen and the resulting compounds of these reactions may
be in the form of liquid, solid and gaseous state. This
transition stage may be temporary or permanent which
yields solid char which is used as landfills and the gases are
used are used in automotive fuels on condensation [3]. A
new approach in the heating system was developed to
recover the hydrocarbons from waste tire in a fixed bed
reactor under inert atmosphere. It was noticed that at 475o
C,
the pyrolysis reaction yielded optimum liquid/gas at a vapor
residence of 5 sec. The physio-chemical analysis includes
elemental analysis, gas chromatography mass spectrometry,
Fourier transform infrared analysis and distillation showed
the presence of hydrocarbon limonene, short and long chain
alkyl, aromatic hydrocarbons in various quantities [11-13].
Bicycle waste tire was used in a semi batch pyrolytic reactor
at 450o
C to 650o
C with a heating rate of 20o
C per min which
yield optimum liquid output at 600o
C. The reaction time,
reaction temperature and yield of liquid/gas were analyzed
in detail and the TPO was characterized using thermo
gravity, FT IR, and GC MS techniques. It was noticed that
the calorific value of TPO was very much comparable with
straight diesel and can be used in IC engine without any
modifications [4]. Few studies were also reported mainly on
thermogravimetric analysis because that was the only
technique available in earlier period to estimate the
conversion rate of solid to liquid and liquid to gases in the
tire pyrolysis process. This process showed weight loss
pattern at different temperature of pyrolysis process which
may be evident as the decomposition procedure were
styrene butadiene rubber decomposed at higher temperature.
Tire pyrolysis was considered to be non-conventional
method for waste disposal in which the reaction was
completed at 550o
C of reaction temperature. It was

_______________________________________________________________________________________
suggested that pyrolysis was very much suitable in
recovering oil from waste tires and the proximate and
elemental analysis revealed that the oil was most suited for
the usage in internal combustion engine. In this process the
solid residue of 40%, liquid residue of 50% and gaseous
residue of 10% were noticed [1,14,17].
In the present experimental study, the design and fabrication
of tire pyrolysis batch reactor was carried out and
characterization of TPO was analyzed using GC/MS, FT IR
and elemental analysis. The state of change from solid to
liquid and liquid to gases were noticed at various
temperatures conditions. The physio-chemical properties of
TPO and its blend with straight diesel were also studied in
detail to understand its application in internal combustion
engine.
2. MATERIALS AND METHODS
20 kgs of waste automotive tire were collected from a local
vendor in Chennai. The major composition of waste tire was
found to be vulcanized rubber, metal cords and beadings,
carbon black, sulphur, oxides of zinc and textile fabric as
detailed in Table (1) with the comparison of LMV’s and
HMV’s tires. The metal beading in the tire was carefully
removed and made into small square pieces at 4cm X 4cm
with the help of cutting instruments. The waste rubber
pieces were washed continuously in the flowing water for
1hr at 45o
c to remove the impurities and coating materials.
This process was repeated for two more times to confirm the
removal of impurities which could affect the pyrolysis
process [2]. The Figure (1) shows the block flow diagram of
recovering the TPO from waste tire in the pyrolysis batch
reactor. The reaction yielded three compounds namely solid
char, TPO and gases.
Fig 1 Block diagram for TPO recovery
The distillation process was carried out on the raw TPO for
its usage in internal combustion engine. The composition of
waste tire used in this experimental investigation is given in
Table (1) with the comparison of LMV’s and HMV’s tires.
It can be noticed that the content of rubber was similar were
as the sulphur content was 0.3% higher. All the other
materials were found to be similar to LMV’s and HMV’s
tire as shown in Table (1). Physio-chemical analysis,
Elemental analysis, Gas chromatography Mass spectrometry
and Fourier transform infrared spectrometry analyses were
carried out on the tire pyrolysis oil to understand its
properties and characteristics for its usage in internal
combustion engine. JEOL Gate GC Mate 2 data system with
high resolution and double focusing type and Fourier
transform infrared spectrometry were used to study the
GC/MS pattern and FTIR pattern respectively.
Table 1 Comparison of material composition of Waste tires
Materials Waste
tire (wt
%)
LMV
Tires in
(wt %)
HMV
Tires in
(wt %)
Rubber 46 48 45
Carbon black 21.7 21.5 22
Metal 17 15.5 25
Textile 5.6 5.5 -
Zinc oxide 1.1 1 2
Sulphur 1.3 1 1
Additives 7.3 7.5 5
3. EXPERIMENTATION
The pyrolysis batch reactor was designed using Catia
software with the overall dimension of 400 X 200 X 458
cms as shown in the Figure (2). The reactor consists of two
cylinders; a convergent top, exhaust chute, condensation
chamber, L shaped oil outlet, three induction coil and a
temperature controller. Stainless sheet metal was used for
inner and outer cylinders which are placed over 3 heating
induction coils. The generation of heat was through power
supply which can elevate the temperature upto 750o
C by an
increment of 15o
C/min.
The inner and outer cylinders are separated by 20mm glass
wool which acts as an insulator to reduce the wastage of
heat energy. A metal chute of 20mm diameter, inclined at
12o
was connected to the reactor outlet and directed towards
the condensation chamber as shown in Figure (3). The
condensation chamber was filled with 13 liters of cold water
to convert the smoke/gas into TPO. After condensation, the
TPO occupies the upper layer in the condensation chamber
and are separated from water with the help of L shaped
metallic arrangement [5,10]. The detailed cross-sectional
view and actual pictorial view of the pyrolysis batch reactor
is shown in Figure (3).

_______________________________________________________________________________________
Fig 2 Design of pyrolysis batch reactor
Fig 3 Sectional and pictorial view of pyrolysis batch reactor
The raw tire pyrolysis oil was treated in three stages namely
de-moisturizing, de-sulphurisation, and distillation process
to remove excess moisture, sulphur and sludge respectively
before its usage in compression ignition engine. During the
de-moisturizing process, the raw TPO was heated upto
125o
C to remove excess moisture which was followed by
de-sulphurisation process by adding 10% concentrated
H2SO4 at 70o
C, 250 rpm for 24 hrs. During this settling
period, the impurities and sulphur content is formed as
sludge and occupies the bottom layer. The treated TPO was
carefully separated from the sludge and subjected to
distillation process upto 240o
C. By this process, 92% of
TPO was recovered which can be used in compression
ignition engine [6,8].
4. RESULT AND DISCUSSIONS
4.1 Effect of Reactor Temperature on the Products
Yield
The Table (2) shows the variation in yield of solid char,
liquid and gases at 300o
C, 350o
C, 400o
C and 450o
C
respectively on the pyrolysis batch reactor. It was noticed
the yield of soil char was reduced with the increase in
temperature (i.e) yield of solid char at 300o
C, 350o
C, 400o
C
and 450o
C was found to be 47.5, 45.5, 45.0 and 41.5 % by
weight respectively. The yield of liquid was also almost
similar to solid char showing very minimal variations. The
gases yield was found to be higher with the increase in
temperature of the reactor which may be due to change in
transition state at higher temperature. At 300o
C, 350o
C,
400o
C and 450o
C of reactor temperature, the gas yield was
noticed to be 6.5, 10.0, 12.5 and 18.5% by weight
respectively. Figure (4) also exhibited the yield of gases was
increased with reduction in solid char and liquid at elevated
temperatures [16].
Table 2 Comparison of product yield at different reactor
temperature
Types of
Products
Products yield at different reactor
temperature
(wt %)300o
C 350o
C 400o
C 450o
C
Solid char 47.5 45.5 45 41.5
Liquids 46 44.5 42.5 40
Gases 6.5 10 12.5 18.5
Fig 4 Comparison between reaction temperature and TPO
yield
4.2 Elemental Analysis of TPO
The elemental analysis was carried out on the Tire pyrolysis
oil to identify the presence of various elements, organic and
in-organic materials. It was noticed that TPO contained
81.48%, 6.22%, 0.23%, 1.68%, 7.69% and 2.7% by weight
of carbon, hydrogen, nitrogen, sulphur, oxygen and in-
organic ashes respectively as shown in Table (3).
Table 3 Elemental composition of TPO
Elements Composition (Wt %)
Carbon 81.48
Hydrogen 6.22
Nitrogen 0.23
Sulphur 1.68
Oxygen 7.69
Ashes (Inorganic) 2.7

_______________________________________________________________________________________
Fig 5 GC/MS Mass Spectrum of TPO
Table 4 FT IR analysis of TPO
Frequency of
wavelength ( cm-1
)
Compound functional group
710-815 C-H Bend (Alkenes)
852-1045 C=C Stretch (Alkenes)
1220-1320 C-S Stretch (Amines)
1380-1590 C-H Bend (Alkanes)
1620-1820 C=C Stretch ( Aromatic Compounds)
1905-2150 C=H (Phenyl ring substitute)
2250-2620 C-H Stretch (Aldehydes)
2720-2940 C-H Stretch
2985-3015 C=H Bend
3080-3150 C=C Stretch (Alkenes)
GC/MS analysis was carried out using JEOL Gate GC mate
2 to identify the various compounds present in TPO. 2 ml of
TPO was injected into the spectrometry with a residence
period of 6 sec. The GC/MS mass spectrum showed the
presence of 12 different compounds at various retention
times. The peaks of the of the GC/MS mass spectrum were
detailed as fragmentation patterns and compared with
standard NIST 1 and 2 libraries for the identification of
compounds. Various peaks were seen on the mass spectrum
between retention time 5.55 and 19.15 min. RT 18.95
showed a highest peak of limonene with scan 716 and ions
2532. Limonene was considered to be the major compound
of TPO as it is product of pyrolysing poly-isoprene [7].
Other major peaks were seen at retention time 17.17 and
5.55 which showed the presence of Bicyclo [2.2.1] heptan-
2-one, 3-(4-methoxybenzylidene)-1 7,7-trimethyl and
Cyclohexane 3 methyl-6-(1-methylethenyl) (3R-Trans)
respectively in prominent quantities. Other than the major
compounds Naphthalene, 1,2,4a,5,8,8a-hexahydro ,4,7-
dimethyl-1-(1-methylethyl) and Tricyclo [5.3.1.1(2,6)]
dodecan-11-ol,11-methyl-12-methylene were also seen in
the fragmentation pattern. The GC/MS mass spectrum
generally revealed that tire pyrolysis oil mainly contain
aliphatic and aromatic compounds with concentrations of
46.2% and 30.9% respectively. The gas chromatography
mass spectrum is shown in Figure (5) and the various
compounds present in the TPO is given in Table (4). The
Fourier transform infrared analysis supports the GC/MS data
[7,9].

_______________________________________________________________________________________
Table 5 Composition of various compounds in TPO using GC/MS
Ret
Time
(min)
Name of the compound
Chemical
formula
Scan Ions
5.55 Cyclohexane 3 methyl-6-(1-methylethenyl) (3R-Trans) C6H12 186 1861
10.27 1-Ethyltricyclo[5.2.1.1(2,6)]undue-8-en-11-ol C2H3N3O 370 1830
10.75 Naphthalene, 1,2,3,4-Tetrahydro-2,5,8-Trimethyl C10H8,C13H18 389 1881
11.35 1,1,4a-Trimethyl-5,6-dimethylenedecahydronapthalene
(CH3)3PO4,
C11H2O
414 1900
11.78 Naphthalene, 1,2,4a,5,8,8a-hexahydro,4,7-dimethyl-1-(1-methylethyl) C15H24 431 1938
12.48 Tricyclo[5.3.1.1(2,6)]dodecan-11-ol,11-methyl-12-methylene C10H16 458 1940
12.83 Cycloheptene, 4-methoxy--phenyl C14H18O 475 1923
14.65 Bicyclo[3.1.0]hexan-2-one,6,6-dicyano-5-(1) C6H10 544 1873
16.95 1-Azatricyclo[7.3.0.0(2,7)]dodecan-11-ol-12-one, 8-methyl C14H21 636 2001
17.17 Bicyclo[2.2.1]heptan-2-one, 3-(4-methoxybenzylidene)-1,7,7-trimethyl- C16H20N3 644 2066
18.95 Limonene C19H36N2 716 2532
19.15 1-Phenyl-3-ethylprop-1-ene(1-3)sultine C19H38NH2 723 2194
Table (5) showed the presence of various functional group
with respect to the wave-length frequency of Fourier
transform infrared analysis. From the wave length spectrum
is can be noticed that tire pyrolysis oil mainly contains
aliphatic and aromatic compounds between 1380 cm-1 and
1820cm-1 which was also revealed by GC/MS analysis. C-H
stretch and C-H bend was also seen between 2720-2940 cm-
1 and 2985-3015 cm-1 wave length of FT IR analysis. The
FT IR analysis also revealed the presence of alkenes,
amines, alkanes, aldehydes and phenyl rings in prominent
quantities which were favorable to be used as fuel in internal
combustion engine [15].
Table 6 Comparison of Fuel Properties - TPO with Straight diesel and WPO
Properties Units
Testing
Methods
Straight Diesel TPO WPO
Density @ 15°c kg/m
3
IS:1448 P:16 830 934 835.5
Kinematic viscosity, @ 40°c Cst IS:1448 P:25 2 3.1 2.0
Flash point °c IS:1448 P:20 50 44 42
Fire point °c IS:1448 P:20 56 51 45
Gross Calorific value MJ/kg IS:1448 P:6 43.8 42.9 40.17
Sulphur content % IS:1448 P:33 0.045 0.96 0.030
Carbon residue % IS:1448 P:122 0.35 2.15 82.49
Ash content % IS:1448 P:126 0.01 0.32 0.00023
Cetane Index - IS:1448 P:9 46.2 54 66

_______________________________________________________________________________________
Table 7 Comparison of Fuel Properties-TPO Straight diesel blends
Properties Units
TPO
5
TPO
10
TPO
20
TPO
30
Density @ 15°c kg/m
3
829 834 840 850
Kinematic viscosity, @ 40°c Cst 2.48 2.58 2.64 2.72
Flash point °c 44 46 42 38
Fire point °c 58 60 54 50
Gross Calorific value MJ/kg 42.9 42.6 42.2 41.9
Sulphur content % 0.10 0.28 0.029 0.31
Carbon residue % 0.02 0.06 0.03 0.02
Ash content % 0.08 0.03 0.02 0.02
Cetane Index - 51 50 47 44
The physio-chemical properties of tire pyrolysis oil in
comparison with straight diesel and waste plastic oil are
shown in Table (6). Indian standard 1448 testing method
was adopted to determine properties like density, kinematic
viscosity, flash & fire point, calorific value, sulphur content,
carbon residue, ash content and cetane index. The density of
TPO was found to be 934 at 15o
C which was comparably
higher than straight diesel and WPO. The kinematic
viscosity also showed a significant increase on comparing
with straight diesel and WPO. The flash & fire point was
found to be 44o
C & 51o
C were as straight diesel and WPO
represented 50o
C & 56o
C and 42o
C & 45o
C respectively.
The gross calorific value of TPO laid in-between straight
diesel and WPO but the sulphur content showed an
enormous increase by more than 21.3% than straight diesel
which confirms the necessity of de-sulphurisation process.
The cetane index was found to be 54 which were higher than
straight diesel and lower than WPO. The pH value of TPO
was noticed to be marginally acidic which make it difficult
to handle and storage [6,15].
The blends of TPO with straight diesel at 5%, 10%, 20%
and 30% are shown in Table (7) which gives us an idea of
its usage in internal combustion engines. It can be seen that
with increase in tire pyrolysis blend with straight diesel,
density, kinematic viscosity, flash & fire point, sulphur
content and carbon residue was increased were as gross
calorific value and cetane index represented a decreasing
trend. From the table it is evident that more quantity of TPO
will be required to get a similar power output of straight
diesel.
5. CONCLUSION
From the present experimental investigation, following
conclusions were derived,
 Pyrolysis process was one of the best methods to treat
waste tire under solid waste management technique.
 A pyrolysis batch reactor was successfully designed and
fabricated with a handling capacity of 10 kgs per cycle
and the overall yield of TPO was found to be 42%.Yield
of TPO was noticed at higher levels with the increase in
temperature above 450o
C.
 De-moisturizing, de-sulphurisation, and distillation
process were carried out to remove excess moisture,
sulphur removal and sludge isolation in the presence of
10% concentrated H2SO4. By this process 92% of
distilled TPO was recovered.
 The elemental analysis revealed the presence of carbon,
hydrogen, sulphur and oxygen at 81.48%, 6.22%, 1.68%
and 7.69% respectively.
 The GC/MS analysis showed evidence of Limonene
presence at major quantity along with many aliphatic and
aromatic compounds with FT IR analysis as
confirmatory and support.
 The physio-chemical properties of treated TPO were
found to be comparable with straight diesel with higher
sulphur content. The blends of TPO and straight diesel
also showed improvements in density, kinematic
viscosity, flash & fire point and carbon residue with a
marginal decrease in cetane index and calorific value.
ACKNOWLEDGEMENTS
The author would like to acknowledge Sophisticated
Analytical Instrumentation Facility (SAIF), Indian Institute
of Technology Madras and ITA lab Chennai for the support
in analyzing the properties of tire pyrolysis oil.
REFERENCES
[1] Cao Q, Jin LE, Bao WR, Lu YK. Factors influencing
the quality of pyrolytic oil from used tires. Energy
sources Part A 2008; 30: 833-841.
[2] Chang Y. On pyrolysis of waste tyre degradation rate
and product yields. Resource, Conservation and
recycling 1996; 17: 125-139.
[3] Debalaxmi Pradhan and Singh RK. Thermal pyrolysis
of bicycle waste tyre using batch reactor.
International Journal of Chemical engineering and
applications 2011; 2(5): 332-336.
[4] Elena Cristina Rada, Marco Ragazzi, Roberto Dal
Maschio, Mario Ischia, Valeriu Nicolae Panaitescu.
Energy recovery from tyre waste through thermal
options. U.P.B.Sci.Bull, Series D 2012; 74: 201-210.
[5] Islam MR, Islam MN, Mustafi NN, Rahim MA and
Haniu H. Thermal recycling of solid tire waste for
alternative liquid fuel: the first commercial step in
Bangladesh. Procedia Engineering 2013; 56:573-582.

_______________________________________________________________________________________
[6] Islam MR, Haniu H, Beg Alam MR. Liquid fuels and
chemicals from pyrolysis of motorcycle tyre waste
product yields, composition and related properties.
Fuel 2008; 87: 3112-3122.
[7] Laresgoiti MF, Caballero BM, De Marco I, Torres A,
Cabero MA and Chomon MJJ. Characterization of
liquid products obtained in tire pyrolysis.
J.Ann.App.Pyrolysis 2004; 71: 917-934.
[8] Murugan S, Ramaswamy MC and Nagarajan G. A
comparative study on the performance, emission and
combustion studies of a DI diesel engine using
distilled tyre pyrolysis oil-diesel blends. Fuel 2008;
87(10-11): 2111-2121.
[9] Mirmiran S, Pakdel H. Roy C. Characterization of
used tire vacuum pyrolysis oil: Nitrogenous
compound from the naptha fraction. J. Anal. Appl.
Pyrolysis 1992; 22: 205-215.
[10] Morillo R, Aylon E, Navarro MV, Callen MS,
Aranda A, Mastral AM. The application of thermal
processes to valorize waste tyre. Journal of Fuel
Processing Technology 2006; 87: 143-147.
[11] Rofiqul Islam M, Praveen M, Haniu H, Islam Sarkar
MR. Innovation in pyrolysis technology for
management of scrap tire: a solution of energy and
environment. Int. J.Env. Sci.and Engg.2010; 1(1): 89-
96.
[12] Sharma VK, Mincarini M, Fortuna F, Cognini F and
Cornacchia G. Disposal of waste tires for energy
recovery and safe environment-review. Ene. Con. and
man. 1998; 39:511-528.
[13] Suhanya M, Thirumasrmurugan M, Kannadasan T.
Recovery of oil form waste tyres using pyrolysis
method: a review. International Journal of research in
Engineering & Technology 2013; 1(2): 81-89.
[14] Taxin Su, Liming Ren, Wenyi Deng. Experimental
study on NO reduction by reburning of waste tire.
Procedia Env. Sci. 2013; 18: 359-365.
[15] Williams PT, Beeseler S. Pyrolysis
thermogravimetric analysis of tyre and tyre
components. Fuel 1995; 74: 1277-1283.
[16] Williams PT, Brindle AJ. Temperature selective
condensation of tyre pyrolysis oils to maximize the
recovery of single ring aromatic compounds. Fuel
2003; 82: 1023-1031.
[17] Williams PT, Waste treatment and disposal, 2nd
edition; Wiley & Sons, London 2005.

Design and development of pyrolysis batch reactor and characterization of tire pyrolysis oil using gc ms and ft ir

More Related Content

What's hot (20)

Viewers also liked (18)

Similar to Design and development of pyrolysis batch reactor and characterization of tire pyrolysis oil using gc ms and ft ir (20)

More from eSAT Journals (20)

Recently uploaded (20)

Design and development of pyrolysis batch reactor and characterization of tire pyrolysis oil using gc ms and ft ir