Development of Software Using Matlab for Design Optimization of Brake for Minibike

IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE)
e-ISSN: 2278-1684,p-ISSN: 2320-334X, Volume 12, Issue 6 Ver.III (Nov. - Dec. 2015), PP 24-29
www.iosrjournals.org
DOI: 10.9790/1684-12632429 www.iosrjournals.org 24 | Page
Development of Software Using Matlab for Design Optimization
of Brake for Minibike
Anil Kumar Garikapati1
, Dr. N. Govind2
, Dr.RavindraKommineni3
,V.Anand
Kumar4
1
Associate Professor, Department of Mechanical Engineering, Tirumala College of Engineering, Narasaraopet,
522601,
2
Associate Professor, Department of Mechanical Engineering, RVRJC College of Engineering, Guntur,522019,
3
Professor&HOD, Department of Mechanical Engineering, RVRJC College of Engineering,Guntur,5220019
4
Assistant Professor, Department of Mechanical Engineering,VNR Vignana Jyothi Institute of Engineering and
Technology, Hyderabad..
Abstract: Mini bikes are normally preferred by for their light weight. Hence attention needs to be focused on
weight while configuring each and every key element like brake, gear box,engine, clutchs etc. Design
optimization of brake for one such mini brake has been taken up in this work. To start with, mathematical model
of the brake has been established so as to bring out the relation between key parameters of the design and the
same has been used in the later stage so as to formulate the optimization strategy. Configuring the brake by
choosing restraining value of width of brake lining in place of choosing restraining value of size of brake drum
yielded to reduction of volume and hence weight. Optimized design lead to increased area of lining which in
turn will reduce dissipation of energy per unit area. Accordingly it has bagged additional merits like reduction
in operating temperature and wear. Further a general purpose software has been developed using MATLAB for
design optimization of brake. For accomplishing this, formulation has been transformed in form of a code in
MATLAB. Programme has been written with interactive mode of operation which means upon executing the
programme it prompts the user to enter the value of inputs and subsequently it generates the outputs.
Keywords: Optimization, Mathematical modelling, Brake lining, MATLAB, etc .
I. Introduction
Light weight vehicles like mini bikes need to be configured while giving utmost attention to key
elements like brake, clutch, gears, etc in optimal manner. Mathematical modeling of the intended subsystem
needs to be established before making an attempt for optimization. Relation between various design parameters
need to be understood so as to carry out optimization effectively. Primary objective of the optimization would
be reduction of volume and hence weight. Design optimization of brake meant for one such mini bike is
considered in this project. One such typical brake of a mini bike is shown in Fig. 1.
Fig. 1. Typical brake of a mini bike
To begin with efforts have been put up to understand the state of art for design optimization procedure
that needs to be applied for the planned requirement.
Each and every system has been studied and developed so as to meet safety. In place of having air bag,
apt suspension systems, good handling and safe surrounding, there is one another critical system in the vehicle
which is nothing but brake systems. Without proper brake system, vehicle will put a passenger in risk.

Development of Software Using Matlab for Design Optimization of Brake for Minibike
Therefore, it is must for all vehicles to have suitable brake system. In this work carbon ceramic matrix disc
brake material used for estimating normal force, shear force and piston force. The typical disc brake has been
modeled in ANSYS and thermal analysis and modal analysis were done and the deflection, heat flux,
temperature of disc brake are calculated. This is essential to know how disc brake works more effectively, which
can assist to reduce the hazard that may happen any time [1]. The objective of this paper is to optimize the
design of brake drum by reverse engineering approach. Optimization is carried out by altering the material of
the brake drum, under various braking time and operational situations. Brake drum is optimized and evaluated
different stresses, displacement values, increase in temperature on various braking instances and heat transfer
rate. Optimized results thus obtained are compared for aluminium and controlled expansion material alloys. It
completes that the controlled expansion alloys can be a right candidate material for the brake drum installations
of light commercial vehicles and it also enhances the braking performance [2]. Disc brake consists of a cast iron
disc attached to the wheel hub with bolt and a fixed housing called caliper. The caliper is attached to some fixed
part of the vehicle like the axle casing or the stub axle as it is cast in two different parts out of which each part
consists of a piston. Between each piston and the disc there exists a friction pad held in place by retaining pins,
spring plates. The passages are so attached to another one for bleeding. Each cylinder consists of rubber sealing
ring between the cylinder and piston. Due to the usage of brakes on the disc brake rotor, heat generates due to
friction and this temperature so produced has to be dissipated across the disc rotor cross section. The objective
of this paper is to study the temperature and also structural characteristics of the solid disc brake during short
and emergency braking with four dissimilar materials. The temperature distribution depends on different factors
such as friction, material and speed. The effect of the angular velocity and the contact pressure creates the
temperature rise of disc brake. The finite element analysis for two-dimensional model is considered due to the
heat flux ratio uniformly distributed in circumferential direction. Currently the disc brakes are made up of cast
iron and cast steel. With the value at the hand the best suitable material for the brake drum can be determined
with maximum life span. The detailed drawings of all subsystems are provided [3]. An automobile brake disc or
rotor is a device for retarding the motion of a wheel while it runs at a certain speed. Mostly used brake rotor
material is cast iron which spends much fuel due to its high specific gravity. The objective of this paper is to
develop the material selection methodology and choose the best material for the application of brake disc system
highlighting on the substitution of this cast iron by any other lighter material. Two methods are discussed for the
selection of materials. Material performance requirements were studied and alternative solutions are evolved
among cast iron, aluminium alloy, titanium alloy, ceramics and composites. Mechanical properties including
compressive strength, friction coefficient, wear resistance, thermal conductivity and specific gravity as well as
cost, are used as the chief parameters in the material selection stages. The analysis yielded to aluminium metal
matrix composite as the most correct material for brake disc system [4]. Brake lining material is an improper
conductor of heat; most of the heat passes into the disc during braking. Under simple use, brake disc may reach
high temperatures. The coefficient of friction between the disc and lining is condensed excessively at these high
temperatures, so that extra pedal pressure is required. So as to reduce the brake fade operation the design of disc
should be in such a way that the heat generated during braking should be easily carried away to the atmosphere
so that brake fade operation will not occur. Also optimization of weight can decrease the manufacturing cost
along with the sluggishness effect of the disc [5]. In this analysis, a new wedge disc brake performance is
evaluated using brake dynamometer and Taguchi method. The Taguchi method is frequently used in the
industry for optimizing the product and the process conditions. Taguchi orthogonal design method is used to
increase better understanding about the factors that effect of wedge brake enactment using L9 orthogonal array.
Three control factors were reflected as applied pressure, vehicle speed and wedge angle inclination, each at
three levels is chosen. It can be concluded that Taguchi method is trustworthy and decrease the time and
experimental costs. In addition, the results shown that the applied pressure and wedge angle are the most
noteworthy parameters for evaluation of the wedge disc brake [6].
As can be seen, optimization techniques are not so effective and practical implementation of the same
would be tedious. Under these circumstances great need exists for design optimization of brake with following
merits.
 Reduction of volume and hence weight
 Increased area of lining
 Reduction in dissipation of energy per unit area
II. Design Inputs
 Coefficient of friction for brake = 0.4
 Size of drum = 200 mm
 Allowable stress = 100 MPa
 Maximum pressure rating of brake = 0.23 MPa
 Torque = 40000 N-mm

III. Design Constraints
 Size of drum < 200 mm
 Width of brake lining < 25 mm
 Wrap angle < 2900
 Factor of safety (FOS) > 1.5
IV. Mathematical Modeling
Design parameters are shown in Fig. 2.
Fig. 2. Design parameters
Where
ω: Angular velocity
α: Wrap angle
r: Outer radius of brake drum
F1, F2: Forces acting on either side of brake band
Taking equilibrium of forces acting on parallel and orthogonal directions to that of tangent to a small element of
brake at its center yields to
  (1)0
2
cos
2
cos 











 

pwrd
d
F
d
dFF
  (2)0
2
sin
2
sin 











 

pwrd
d
F
d
dFF
Where
µ: Coefficient of friction for brake
p: Pressure acting on lining
w: Width of brake lining
1
2
osand
22
in0,d 














d
c
dd
sAs
And
Fdtocomparednegligiblebecomes
2
F 






 d
d
With all above
Equation (1) reduces to
dF = µ.p.w.r.d (3)
Further equation (2) reduces to
F = p.w.r (4)
Substituting equation (4) in equation (3) and integrating gives
   ddF
F
1
   
 02
ln 
F
FF

ln F – ln F2 = µ. (5)
µln 2F
F

(6)
µ
2F
F 
e
Which represents tangential force in the brake as a function of position along the brake
Thenhen 1FFW 
With which equation (6) becomes
(7)µ
2F
1F 
e
Equation (7) conveys that when  approaches α force attains its maximum value i.e. F1
Considering this, equation (4) can be rewritten as
F1 = pmax.w.r (8)
Equation 8 highlights the disadvantage of the brake that wear of the lining is more at high pressure side of
the brake. Due to this the lining should be swapped when it is worn out at only one side, or it has to be swapped
near around mid of its life or brake should have more lining materials with different friction coefficients so as to
avoid replacement of lining very often.
Further relation between torque applied by the brake and force can be expressed as
T = (F1-F2) r (9)
Substituting equations (7) and (8) in(9) yields
T = pmax. w.r2
(1-e-µα
) (10)
Equation (10) relates maximum constraining torque of the brake with its dimensions and its maximum pressure
(Compressive)
V. Existing Design
Width of brake lining for the existing design has been calculated from equation (10) as follows
(11)μαe12rmaxp
Tw





 

From this expression w = 20 mm
Area of brake lining can be expressed as
A = α.r.w (12)
From this expression A = 10142 mm2
Factor of safety can be expressed as
From this expression working stress = 66.67 MPa
Working stress can also be expressed as
From equation (4)
F =460.8 N
d1: Size of link
Substitution of necessary inputs gives d1= 3 mm
VI. Design Optimization
Width of brake lining for the existing design is 20 mm as calculated using equation (11). However its
restraining value imposed by space constraints is 25 mm. It is decided to explore the advantage of utilizing the
(13)
stressWorking
stressAllowable
FOS
(14)
2
14
F
linkofArea
Force
stressWorking







d


width of lining to the fullest extent permitted so as to optimize the existing design. Accordingly size of drum has
been reworked taking the restraining value of width of lining i.e. 25 mm as follows.
Equation (10) can be rearranged as
(15)
μαe1w
max
p
Tr





 

From this expression r = 90 mm
From which size of drum (D) = 2 x r = 180 mm
From equation (12)
Area of brake lining, A = 11328 mm2
From equation (14)
Size of link d1 = 3.1 mm
VII. Results And Discussion
Parameters for optimized design are compared with that of existing one in table 1.
Table 1. Summary of design parameters
Sl.
No.
Parameter Existing design Optimized
design
1. Size of drum 200 mm 180 mm
2. Width of lining 20 mm 25 mm
3. Area of lining 10142 mm2
11328 mm2
4. Size of link 3 mm 3.1 mm
5. Torque 40000 N-mm
6. Pressure 0.23 MPa
 Both the configurations meets the design constraints
 But for the same torque and pressure capability of brake lining optimized design yields to lesser drum
size which contributes a lot to both volume and weight.
 Further brake having higher lining area dissipates less energy per unit area which imparts two high
order merits to the design which are: Lower operating temperature and less wear of lining
VIII. Development Of Software In Matlab
General purpose software has been developed using MATLAB for design optimization of brake. For
accomplishing this formulation stated in section (5) has been transformed in to some form of a code in
MATLAB and the screen shot of associated m-file is shown in Fig. 3.
Fig. 3. Screen shot of associated m-file

Programme has been written with interactive mode of operation which means upon executing the
programme it prompts the user to enter the value of inputs as shown in Fig. 4.
Fig. 4. Inputs needed to execute the code
Subsequently programme will generate the outputs as shown in Fig. 5.
Fig. 5. Outputs generated by the code
IX. Conclusions
Reconfiguring the design of brake for mini bike by choosing the restraining value of lining width rather
than choosing restraining value of size of drum yielded to reduction in volume and weight and hence resulted in
optimizing the design. It also reduced the operating temperature and wear.
Acknowledgement
This research is supported by Science and Engineering Research Council (SERC), Department of
Science and Technology (DST) New Delhi, INDIA. (SR/SR3/MERC-098/2007)
References
[1]. Swapnil R. Abhang and D.P.Bhaskar, “Design and Analysis of Disc Brake”, International Journal of Engineering Trends and
Technology (IJETT) – Volume 8, Number 4- Feb 2014.
[2]. Meenakshi Kushal and Suman Sharma, “Optimization of Design of Brake Drum of Two Wheeler through Approach of Reverse
Engineering by Using ANSYS Software”, IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE), Volume 12, Issue 4
Ver. IV, PP 70-75, July - August 2015.
[3]. Velveeta Lakshmikanth Chowdary, N. Amara Nageswara Rao, “Design & Analysis of a Disc Brake using FEA”, Vol, 04, Issue 10,
October– 2014, International Journal of Computational Engineering Research (IJCER).
[4]. M.A. Maleque, S.Dyuti and M.M. Rahman, “Material Selection Method in Design of Automotive Brake Disc” Proceedings of the
World Congress on Engineering 2010 Vol III, WCE 2010, June 30 - July 2, 2010, London, U.K..
[5]. Borchate Sourabh Shivaji, Prof. N. S. Hanamapure, Swapnil S. Kulkarni, “Design, Analysis And Performance Optimization Of Disc
Brake”, International Journal of Advanced Engineering Research and Studies E-ISSN2249–8974.
[6]. Mostafa M. Makrahy, Nouby M. Ghazaly, k. A. Abd El-Gwwad, K. R. Mahmoud and Ali M. Abd-El-Tawwab, “Optimization of a
New Wedge Disc Brake Using Taguchi Approach”, International Journal of Modern Engineering Research (IJMER) , Vol. 3, Issue.
6, Nov - Dec. 2013 pp-3461-3465.

Development of Software Using Matlab for Design Optimization of Brake for Minibike

More Related Content

What's hot (19)

Viewers also liked (10)

Similar to Development of Software Using Matlab for Design Optimization of Brake for Minibike (20)

More from iosrjce (20)

Recently uploaded (20)

Development of Software Using Matlab for Design Optimization of Brake for Minibike