Ecilop Easy assembling manual
- 1. Ecilop Easy Assembling Manual (2013)
- 2. Ecilop Easy Technical data: Dimensions without propellers - 0.5 x 0.5 x 0.4 m Weight of the frame - 0,6 kg The full flight weight - 2,2 kg
- 3. Ecilop Easy The package contains the following items shown in the images below:
- 4. Ecilop Easy The package contains the following items shown in the images below:
- 5. Ecilop Easy The package contains the following items shown in the images below:
- 6. Ecilop Easy The package contains the following items shown in the images below:
- 7. Ecilop Easy You will need the following additional components (not included):
- 8. Ecilop Easy You will need the following additional components (not included): 1. A digital camera (Sony NEX-5N is recommended); 2. A remote control unit (Futaba T8J or a different mode); 3. Quadcopter flight controller with a camera stabilization function (DJI NAZA or a different model); 4. Two gyroscopes (Turnigy Mini MEMS or a different model); 5. Two park-size servos (MKS DS8910 or a different model); 6. Four engines: the distance between mounting screws should be 19 mm (MT3506-25 or a different model); 7. Four propellers: maximal diameter 14" (APC12x3.8 or a different); 8. Four speed controllers (T-Motor ESC 18A or a different model); 9. A battery (5000mAh 4S 25C or a different 3-5S model); 10. An FPV camera with a wide lens (optional); 11. A video transmitter (FOXTECH 5.8G 200mw or a different model); 12. Video goggles with a receiver (Fat Shark or a different model).
- 9. Ecilop Easy Assembly instruction 1. Install the camera tilt axis lock into the axial unit. 2. Fasten two balance beam stands using two screwdrivers on its opposite sides. Medium strength threadlocker must be applied.
- 10. Ecilop Easy Assembly instruction 3. Use bolts to fasten two fixers of the camera's second tilt axis. Use moderate torque.
- 11. Ecilop Easy Assembly instruction 4. Fasten the springs holder. 5. Fasten the camera lock, but leave the bolts a bit loose.
- 12. Ecilop Easy Assembly instruction 6. The universal camera fixture allows you to install any camera on the drone. The camera is fixated with a regular tripod screw and should be flipped vertically. The ratio of the mass of the camera to the mass of the battery should be in the range of 0.9 - 1.35 (mass of the camera divided by the mass of the battery). ! It is not recommended to use cameras heavier than 650 gr!
- 13. Ecilop Easy Assembly instruction 7. Install and fasten the servo gears. Install under the servo nylon washers to increase the gap if neaded. 8. Attach dampers to the equipment platform using nuts. Medium strength threadlocker must be applied.
- 14. Ecilop Easy Assembly instruction 9. Bolt up the axial unit to ball bearings on the equipment platform. Use washers if you need to fill the gaps. Medium strength threadlocker must be applied.
- 15. Ecilop Easy Assembly instruction 10. Loosen the bolts on the locks and tighten them up again. This operation will help you eliminate the slight deviation of the locks from the rotation axis. Medium strength threadlocker must be applied.
- 16. Ecilop Easy Assembly instruction 11. Bolt up the engine stands to the main frame. Notice the holes on the sides of stands: 6 mm holes must face forward and backward, while chassis stands must be oriented to the left and to the right. Medium strength threadlocker must be applied.
- 17. Ecilop Easy Assembly instruction 12. Put rubber rings on the landing skids. Install the chassis stand locks into the landing skids. Use an epoxyde or cyanoacrylate adhesive to hold them in place. 13. Fasten the landing skids on the chassis stands. Medium strength threadlocker must be applied.
- 18. Ecilop Easy Assembly instruction 14. Attach the electronic equipment platform to the main frame. Hold the rubber dampers with pliers when screwing the bolts. Medium strength threadlocker must be applied. 15. Bolt up the engines. Medium strength threadlocker must be applied.
- 19. Ecilop Easy Assembly instruction 16. Assemble and fasten the frame for the receiver's antennas.
- 20. Ecilop Easy Assembly instruction 17. Install the electronic equipment: a receiver, an autopilot, speed controllers, gyroscopes, a voltage stabilizer, an FPV camera, an OSD module, a video transmitter. The servo-mechanisms are connected to the gyroscopes, gyroscopes are connected to the onboard controller, and the controller is connected to the receiver. To control both gyroscopes (mode and gain), you can use one channel of the receiver or the programmable output of the onboard controller.Gyroscopes should be installed on the servo side. Side tilt (roll) axle gyroscope is to be set on the servo. To minimize influence of the noises of the servo - use double sided sticker with metal plate in between (usually is included in gyroscope kit). Wires must not rub or tap into gyroscope. The cables connecting the moving parts of the drone must be soft and bent into a loop. The cables must pose minimal obstruction to the rotation of structural elements. Use a separate power switch for onboard electronics.
- 21. Ecilop Easy Assembly instruction 18. The LED is powered through an inverter. 3S-5S Li-Po battery can be used as a power source. Connection polarity does not matter. Power soutce: 11-24V AC/DC. Assemble the LED mount using cyanoacrylate glue. Screw on the LED using isolation washers.Fixate the LED mount and wires on the aircraft frame. Connect to the power source.
- 22. Ecilop Easy Assembly instruction 19. Take the lens off the camera. Fasten the camera body on the gimbal. Install the lens.
- 23. Ecilop Easy Assembly instruction 20. Install the battery platform on the balance beams. Glue the soft edge padding to the balance beam stands to ensure close contact with the battery. Select thick or thin spacers, depending on the thickness of your battery. 21. Use peel-n-stick bands to lock the battery in place. To help the battery cable bend, move the battery connector from the cable to the body of the battery.
- 24. Ecilop Easy Assembly instruction 22. Put the drone on the side. Move the battery along the balance beam stands to achieve a perfect balance. Lock the battery platform in the necessary position. 23. Put the drone on the landing skids. Move the battery forward and backward to reach acceptable balance in the lengthwise direction. If necessary, turn the battery platform. Mark the right fixation position on the battery. Always use identical batteries.
- 25. Ecilop Easy Assembly instruction 24. Loosen the camera lock bolts. Move the camera left and right to reach optimal balance in the lateral direction. Lock the camera in the necessary position. 25. Install the springs between the servo gear and the frame. Springs Ecilop V1209 1.0N/mm (stronger, default) - This type of springs is used in most cases. Springs Ecilop V1209 0.4N/mm (weaker, optional) - With these springs installed, the inertial stabilization effect is stronger, but some swaying may occur. These springs require more precise adjustment of the camera mount and the use of softer cables and faster servo gears.
- 26. Ecilop Easy Assembly instruction 26. Configure the electronic 27. Turn the drone on and check equipment as specified in the the gyroscopes' reaction. manual for your additional When the equipment is turned equipment. on, the gimbal must be stable, otherwise the gyroscopes will be initialized incorrectly and the camera will be tilted. Switch to reverse, if necessary. Use the "normal" mode for gyroscopes. Start with the maximum reaction value. If the servo gear starts vibrating, reduce the gyroscope reaction value. Push the battery with a finger: if it swings, increase the gyroscope gain value.
- 27. Ecilop Easy Assembly instruction video
- 28. Ecilop Easy Have a nice fly and stable video!