Em notes

Lectures notes
On
Engineering Mechanics
Course Code- BME-101
Prepared by
Prof. Mihir Kumar Sutar
Asst. professor,
Department of Mechanical Engg.

Lesson Plan
Subject: Engineering Mechanics (BME- 101),
Date Lecture Topics to be covered
08.01.2015 Lecture 1 Concurrent forces on a plane: Introduction to engineering
mechanics,
09.01.2015 Lecture 2 Composition of forces, parallelogram law, numerical
problems.
10.01.2015 Lecture 3 Resolution of forces, equilibrium of collinear forces, super
position and transmissibility, free body diagram,
12.01.2015 Lecture 4 Equilibrium of concurrent forces: Lami’s theorem, method of
projection, equilibrium of three forces in a plane,
15.01.2015 Lecture 5 Method of moments, numerical problems on equilibrium of
concurrent forces
16.01.2015 Lecture 6 Friction: Definition of friction, static friction, dynamics
friction, coefficient of friction, angle of friction, angle of
repose. Wedge friction, simple friction problems based on
sliding of block on horizontal and inclined plane and wedge
friction
17.01.2015 Lecture 7 Ladder and rope friction, simple problems on ladder and rope
friction.
19.01.2015 Lecture 8 General case of parallel forces, center of parallel forces,
numerical problems.
22.01.2015 Lecture 9 Center of gravity, centroid of plane figure and curves,
numerical examples.
29.01.2015 Lecture 10 Centroid of composite figures figure and curves, numerical
problems.
30.01.2015 Lecture 11 Numerical examples on centroid of plane figure and curves
31.01.2015 Lecture 12 Composition and equilibrium of forces in a plane:
Introduction to plane trusses, perfect, redundant truss,

02.02.2015 Lecture 13 Solving problem of truss using method of joint.
05.02.2015 Lecture 14 Numerical examples on solving truss problems using method
of joint.
06.02.2015 Lecture 15 Method of section, numerical examples.
07.02.2015 Lecture 16 Numerical examples on method of joint and method of
section
09.02.2015 Lecture 17 Principle of virtual work: Basic concept, virtual displacement,
numerical problems
12.02.2015 Lecture 18 Numerical problems on virtual work.
13.02.2015 Lecture 19 Numerical problems on virtual work.
14.02.2015 Lecture 20 Moment of Inertia of plane figure with respect to an axis in its
plane, numerical examples.
16.02.2015 Lecture 21 Moment of Inertia of plane figure with respect to an axis and
perpendicular to the plane, parallel axis theorem, numerical
examples.
19.02.2015 Lecture 22 Numerical examples on MI of plane figures.
20.02.2015 Lecture 23 Rectilinear Translation: Kinematics of rectilinear translation,
displacement, velocity, acceleration, numerical problems on
rectilinear translation
21.02.2015 Lecture 24 Principle of Dynamics: Newton’s Laws, General equation of
motion of a particle, differential equation of rectilinear
motion, numerical problems.
23.02.2015 Lecture 25 Numerical problems on principle of dynamics
26.02.2015 Lecture 26 D’Alembert’s Principle: Basic theory and numerical
problems.
27.02.2015 Lecture 27 Numerical problems on D’Alembert’s Principle.
28.02.2015 Lecture 28 Momentum and Impulse: Basic theory and numerical

problems
02.03.2015 Lecture 29 Numerical problems on momentum and impulse.
07.03.2015 Lecture 30 Work and Energy: Basic theory and numerical problems
09.03.2015 Lecture 31 Ideal systems: Conservation of energy: Basic theory and
numerical problems
12.03.2015 Lecture 32 Impact: Plastic impact, elastic impact, semi-elastic impact,
coefficient of restitution numerical problems on impact on
various conditions.
13.03.2015 Lecture 33 Numerical problems on impact.
14.03.2015 Lecture 34 Curvilinear Translation: Kinematics of curvilinear translation,
displacement, velocity and acceleration, numerical problems
on curvilinear translation
16.03.2015 Lecture 35 Differential equation of curvilinear motion: Basic theory and
numerical problems
19.03.2015 Lecture 36 Motion of a Projectile:
20.03.2015 Lecture 37 Numerical problems on projectile for different cases.
21.03.2015 Lecture 38 D Alembert’s Principles in Curvilinear Motion: Basic theory
and numerical problems.
23.03.2015 Lecture 39 Rotation of rigid body: Kinematics of rotation and numerical
problems.
26.03.2015 Lecture 40 Numerical problems on rotation of rigid bodies.

1
Mechanics
It is defined as that branch of science, which describes and predicts the conditions of
rest or motion of bodies under the action of forces. Engineering mechanics applies the
principle of mechanics to design, taking into account the effects of forces.
Statics
Statics deal with the condition of equilibrium of bodies acted upon by forces.
Rigid body
A rigid body is defined as a definite quantity of matter, the parts of which are fixed in
position relative to each other. Physical bodies are never absolutely but deform slightly
under the action of loads. If the deformation is negligible as compared to its size, the
body is termed as rigid.
Force
Force may be defined as any action that tends to change the state of rest or motion of a
body to which it is applied.
The three quantities required to completely define force are called its specification or
characteristics. So the characteristics of a force are:
1. Magnitude
2. Point of application
3. Direction of application

2
Concentrated force/point load
Distributed force
Line of action of force
The direction of a force is the direction, along a straight line through its point of
application in which the force tends to move a body when it is applied. This line is
called line of action of force.
Representation of force
Graphically a force may be represented by the segment of a straight line.
Composition of two forces
The reduction of a given system of forces to the simplest system that will be its
equivalent is called the problem of composition of forces.
Parallelogram law
If two forces represented by vectors AB and AC acting under an angle α are applied to
a body at point A. Their action is equivalent to the action of one force, represented by
vector AD, obtained as the diagonal of the parallelogram constructed on the vectors
AB and AC directed as shown in the figure.

3
Force AD is called the resultant of AB and AC and the forces are called its
components.
 2 2
2R P Q PQ Cos   
Now applying triangle law
( )
P Q R
Sin Sin Sin   
 

Special cases
Case-I: If α = 0˚
 2 2 2
2 0 ( )R P Q PQ Cos P Q P Q       
R = P+Q
Case- II: If α = 180˚
 2 2 2 2 2
2 180 ( 2 ) ( )R P Q PQ Cos P Q PQ P Q P Q          
P Q R
Q P R

4
Case-III: If α = 90˚
 2 2 2 2
2 90R P Q PQ Cos P Q     
α = tan-1
(Q/P)
Resolution of a force
The replacement of a single force by a several components which will be equivalent in
action to the given force is called resolution of a force.
Action and reaction
Often bodies in equilibrium are constrained to investigate the conditions.
Q
R
P
α
w

5
Free body diagram
Free body diagram is necessary to investigate the condition of equilibrium of a body or
system. While drawing the free body diagram all the supports of the body are removed
and replaced with the reaction forces acting on it.
1. Draw the free body diagrams of the following figures.
2. Draw the free body diagram of the body, the string CD and the ring.
R

6
3. Draw the free body diagram of the following figures.
Equilibrium of colinear forces:
Equllibrium law: Two forces can be in equilibrium only if they are equal in
magnitude, opposite in direction and collinear in action.
Problem 1:
(tension)
(compression)

7
Superposition and transmissibility
Problem 1: A man of weight W = 712 N holds one end of a rope that passes over a
pulley vertically above his head and to the other end of which is attached a weight Q =
534 N. Find the force with which the man’s feet press against the floor.
Problem 2: A boat is moved uniformly along a canal by two horses pulling with forces
P = 890 N and Q = 1068 N acting under an angle α = 60˚. Determine the magnitude of
the resultant pull on the boat and the angles β and ν.
P = 890 N, α = 60˚
Q = 1068 N
2 2
( 2 cos )R P Q PQ   
2 2
(890 1068 2 890 1068 0.5)
1698.01N
     

α
β
ν

8
sin sin sin( )
sin
sin
1068 sin 60
1698.01
33
Q P R
Q
R
   


 







sin
sin
890 sin 60
1698.01
27
P
R

 





Resolution of a force
Replacement of a single force by several components which will be equivalent in
action to the given force is called the problem of resolution of a force.
By using parallelogram law, a single force R can be resolved into two components P
and Q intersecting at a point on its line of action.
Equilibrium of collinear forces:
Equilibrium law: Two forces can be in equilibrium only if they are equal in magnitude,
opposite in direction and collinear in action.

9
Law of superposition
The action of a given system of forces on a rigid body will no way be changed if we
add to or subtract from them another system of forces in equllibrium.
Problem 3: Two spheres of weight P and Q rest inside a hollow cylinder which is
resting on a horizontal force. Draw the free body diagram of both the spheres, together
and separately.
Problem 4: Draw the free body diagram of the figure shown below.

10
Problem 5: Determine the angles α and β shown in the figure.
1
'
1
'
762
tan
915
39 47
762
tan
610
5119




 
  
 

 
  
 




11
Problem 6: Find the reactions R1 and R2.
Problem 7: Two rollers of weight P and Q are supported by an inclined plane and
vertical walls as shown in the figure. Draw the free body diagram of both the rollers
separately.

12
Problem 8: Find θn and θt in the following figure.
Problem 9: For the particular position shown in the figure, the connecting rod BA of
an engine exert a force of P = 2225 N on the crank pin at A. Resolve this force into two
rectangular components Ph and Pv horizontally and vertically respectively at A.
Ph = 2081.4 N
Pv = 786.5 N
Equilibrium of concurrent forces in a plane
 If a body known to be in equilibrium is acted upon by several concurrent,
coplanar forces, then these forces or rather their free vectors, when
geometrically added must form a closed polygon.
 This system represents the condition of equilibrium for any system of
concurrent forces in a plane.
w

13
tan
sec
aR w
S w




Lami’s theorem
If three concurrent forces are acting on a body kept in an equllibrium, then each force
is proportional to the sine of angle between the other two forces and the constant of
proportionality is same.
sin sin sin
P Q R
  
 
   sin90 sin 180 sin 90
aRS W
 
 
 
S
W

14
Problem: A ball of weight Q = 53.4N rest in a right angled trough as shown in figure.
Determine the forces exerted on the sides of the trough at D and E if all the surfaces
are perfectly smooth.
Problem: An electric light fixture of weight Q = 178 N is supported as shown in
figure. Determine the tensile forces S1 and S2 in the wires BA and BC, if their angles
of inclination are given.
1 2 178
sin135 sin150 sin 75
S S
 
1 cosS P 
W
S = Psecα

15
sinbR W S  
Problem: A right circular roller of weight W rests on a smooth horizontal plane and is
held in position by an inclined bar AC. Find the tensions in the bar AC and vertical
reaction Rb if there is also a horizontal force P is active.
Theory of transmissiibility of a force:
The point of application of a force may be transmitted along its line of action without
changing the effect of force on any rigid body to which it may be applied.
Problem:
sin
cos
tan
P
W
W P



  
 

16
0X 
1 2
2
1
2
1
cos30 20sin 60 sin30
3 3
20
2 2 2
3
10 3
2 2
S S
S
S
S
S
 
 
 
2 13 20 3S S  (1)
1 2
1
2
1
2
0
sin30 cos30 cos60 20
3 20
20
2 2 2
3
30
2 2
d
Y
S S S
S
S
S
S

  
  
 

1 23 60S S  (2)
Substituting the value of S2 in Eq.2, we get
 1 1
1 1
1
3 3 20 3 60
3 60 60
4 0
S S
S S
S
  
  

1 0S KN
2 20 3 34.64S KN 

17
Problem: A ball of weight W is suspended from a string of length l and is pulled by a
horizontal force Q. The weight is displaced by a distance d from the vertical position
as shown in Figure. Determine the angle α, forces Q and tension in the string S in the
displaced position.
cos
d
l
 
1
cos
d
l
   
  
 
2 2
sin cos 1  
2
2
2
2 2
sin (1 cos )
1
1
d
l
l d
l
   
 
 
Applying Lami’s theorem,
sin90 sin(90 ) sin(180 )
S Q W
 
 
 
W

18
2 2
2 2
sin(90 ) sin(180 )
cos
1sin
Q W
d
W
W l
Q
l d
l
Wd
Q
l d
 



 
 
 
   

 

2 2
2 2
1sin
W W
S
l d
l
Wl
l d

 



Problem: Two smooth circular cylinders each of weight W = 445 N and radius r = 152
mm are connected at their centres by a string AB of length l = 406 mm and rest upon a
horizontal plane, supporting above them a third cylinder of weight Q = 890 N and
radius r = 152 mm. Find the forces in the string and the pressures produced on the floor
at the point of contact.
203
cos
304
48.1



  
sin138.1 sin138.1 83.8
597.86
g e
g e
R R Q
R R N
 
  
Rg Rf
Q

19
Resolving horizontally
0
cos48.1
597.86cos48.1
399.27
f
X
S R
N





Resolving vertically
0
sin 48.1
445 597.86sin 48.1
890
d f
Y
R W R
N

 
 


890
399.27
eR N
S N


Problem: Two identical rollers each of weight Q = 445 N are supported by an inclined
plane and a vertical wall as shown in the figure. Assuming smooth surfaces, find the
reactions induced at the points of support A, B and C.
445
sin120 sin150 sin90
aR S
 
385.38aR N 
222.5S N 
S

20
0
cos60 445 sin30
3 222.5
445
2 2
642.302
b
b
b
Y
R S
R
R N

 
  
 

0X 
sin30 cos30
642.302sin30 222.5cos30
513.84
c b
c
R R S
R N
 
 
 
Problem:
A weight Q is suspended from a small ring C supported by two cords AC and BC. The
cord AC is fastened at A while cord BC passes over a frictionless pulley at B and
carries a weight P. If P = Q and α = 50˚, find the value of β.
0X 
sin50 sinS Q  (1)
0Y 
cos50 sin
cos50 (1 cos )
S Q Q
S Q


 
  
Putting the value of S from Eq. 1, we get
Rc

21
cos50 sin
cos50 (1 cos )
sin
cos50 (1 cos )
sin50
1 cos
cot50
sin
0.839sin 1 cos
S Q Q
S Q
Q Q






 
 
  
  

 
  
Squaring both sides,
2 2
0.703sin 1 cos 2cos    
2 2
0.703(1 cos ) 1 cos 2cos     
2 2
2
2
0.703 0.703cos 1 cos 2cos
1.703cos 2cos 0.297 0
cos 1.174cos 0.297 0
63.13
  
 
 

   
   
   
  

22
Method of moments
Moment of a force with respect to a point:
 Considering wrench subjected to two forces P and Q of equal magnitude. It is
evident that force P will be more effective compared to Q, though they are of
equal magnitude.
 The effectiveness of the force as regards it is the tendency to produce rotation
of a body about a fixed point is called the moment of the force with respect to
that point.
 Moment = Magnitude of the force × Perpendicular distance of the line of action
of force.
 Point O is called moment centre and the perpendicular distance (i.e. OD) is
called moment arm.
 Unit is N.m
Theorem of Varignon:
The moment of the resultant of two concurrent forces with respect to a centre in their
plane is equal to the alzebric sum of the moments of the components with respect to
some centre.
Problem 1:
A prismatic clear of AB of length l is hinged at A and supported at B. Neglecting
friction, determine the reaction Rb produced at B owing to the weight Q of the bar.
Taking moment about point A,
cos .
2
cos
2
b
b
l
R l Q
Q
R


 
 

23
Problem 2:
A bar AB of weight Q and length 2l rests on a very small friction less roller at D and
against a smooth vertical wall at A. Find the angle α that the bar must make with the
horizontal in equilibrium.
Resolving vertically,
cosdR Q 
Now taking moment about A,
2
3
3
1 3
.
. cos 0
cos
.
. cos 0
cos
. . cos 0
.
cos
.
cos
dR a
Q l
Q a
Q l
Q a Q l
Q a
Q l
a
l






 
 
  
  
 
 
Problem 3:
If the piston of the engine has a diameter of 101.6 mm and the gas pressure in the
cylinder is 0.69 MPa. Calculate the turning moment M exerted on the crankshaft for
the particular configuration.
B

24
Area of cylinder
2 3 2
(0.1016) 8.107 10
4
A m
 
  
Force exerted on connecting rod,
F = Pressure × Area
= 0.69×106
× 8.107×10-3
= 5593.83 N
Now 1 178
sin 27.93
380
   
  
 

cos
6331.29
cos
S F
F
S N



  
Now moment entered on crankshaft,
cos 0.178 995.7 1S N KN   
Problem 4:
A rigid bar AB is supported in a vertical plane and carrying a load Q at its free end.
Neglecting the weight of bar, find the magnitude of tensile force S in the horizontal
string CD.
Taking moment about A,
0
. cos . sin
2
. sin
cos
2
2 .tan
AM
l
S Q l
Q l
S
l
S Q
 





 
 


25
Friction
 The force which opposes the movement or the tendency of movement is called
Frictional force or simply friction. It is due to the resistance to motion
offered by minutely projecting particles at the contact surfaces. However, there
is a limit beyond which the magnitude of this force cannot increase.
 If the applied force is more than this limit, there will be movement of one body
over the other. This limiting value of frictional force when the motion is
impending, it is known as Limiting Friction.
 When the applied force is less than the limiting friction, the body remains at
rest and such frictional force is called Static Friction, which will be having
any value between zero and the limiting friction.
 If the value of applied force exceeds the limiting friction, the body starts
moving over the other body and the frictional resistance experienced by the
body while moving is known as Dynamic Friction. Dynamic friction is less
than limiting friction.
 Dynamic friction is classified into following two types:
a) Sliding friction
b) Rolling friction
 Sliding friction is the friction experienced by a body when it slides over the
other body.
 Rolling friction is the friction experienced by a body when it rolls over a
surface.
 It is experimentally found that the magnitude of limiting friction bears a
constant ratio to the normal reaction between two surfaces and this ratio is
called Coefficient of Friction.
Coefficient of friction =
F
N
where F is limiting friction and N is normal reaction between the contact surfaces.
Coefficient of friction is denoted by µ.
Thus,
F
N
 
W
P
N
F

26
Laws of friction
1. The force of friction always acts in a direction opposite to that in which body
tends to move.
2. Till the limiting value is reached, the magnitude of friction is exactly equal to
the force which tends to move the body.
3. The magnitude of the limiting friction bears a constant ratio to the normal
reaction between the two surfaces of contact and this ratio is called coefficient
of friction.
4. The force of friction depends upon the roughness/smoothness of the surfaces.
5. The force of friction is independent of the area of contact between the two
surfaces.
6. After the body starts moving, the dynamic friction comes into play, the
magnitude of which is less than that of limiting friction and it bears a constant
ratio with normal force. This ratio is called coefficient of dynamic friction.
Angle of friction
Consider the block shown in figure resting on a horizontal surface and subjected to
horizontal pull P. Let F be the frictional force developed and N the normal reaction.
Thus, at contact surface the reactions are F and N. They can be graphically combined
to get the reaction R which acts at angle θ to normal reaction. This angle θ called the
angle of friction is given by
tan
F
N
 
As P increases, F increases and hence θ also increases. θ can reach the maximum value
α when F reaches limiting value. At this stage,
tan
F
N
  
This value of α is called Angle of Limiting Friction. Hence, the angle of limiting
friction may be defined as the angle between the resultant reaction and the normal to
the plane on which the motion of the body is impending.
Angle of repose

27
Consider the block of weight W resting on an inclined plane which makes an angle θ
with the horizontal. When θ is small, the block will rest on the plane. If θ is gradually
increased, a stage is reached at which the block start sliding down the plane. The angle
θ for which the motion is impending, is called the angle of repose. Thus, the maximum
inclination of the plane on which a body, free from external forces, can repose is called
Angle of Repose.
N = W. cos θ
Resolving horizontally,
F = W. sin θ
Thus, tan
F
N
 
If ɸ is the value of θ when the motion is impending, the frictional force will be limiting
friction and hence,
tan
tan
F
N

 
 

 
 
Thus, the value of angle of repose is same as the value of limiting angle of repose.
Cone of friction
 When a body is having impending motion in the direction of force P, the
frictional force will be limiting friction and the resultant reaction R will make
limiting angle α with the normal.
 If the body is having impending motion in some other direction, the resultant
reaction makes limiting frictional angle α with the normal to that direction.
Thus, when the direction of force P is gradually changed through 360˚, the
resultant R generates a right circular cone with semi-central angle equal to α.

28
Problem 1: Block A weighing 1000N rests over block B which weighs 2000N as
shown in figure. Block A is tied to wall with a horizontal string. If the coefficient of
friction between blocks A and B is 0.25 and between B and floor is 1/3, what should be
the value of P to move the block (B), if
(a) P is horizontal.
(b) P acts at 30˚ upwards to horizontal.
Solution: (a)
Considering block A,
1
0
1000
V
N N



Since F1 is limiting friction,
1
1
1 1
0.25
0.25 0.25 1000 250
F
N
F N N
 
   
1
1
0
0
250
H
F T
T F N

 
 

Considering equilibrium of block B,
2 1
2 1
0
2000 0
2000 2000 1000 3000
V
N N
N N N

  
    

2
2
2 2
1
3
0.3 0.3 1000 1000
F
N
F N N
 
   

29
1 2
0
250 1000 1250
H
P F F N

    

(b) When P is inclined:
2 1
2
2
0
2000 .sin30 0
0.5 2000 1000
3000 0.5
V
N N P
N P
N P

   
   
  

From law of friction,
 2 2
1 1 0.5
3000 0.5 1000
3 3 3
F N P P    
1 2
0
cos30
0.5
cos30 250 1000
3
0.5
cos30 1250
3
1210.43
H
P F F
P P
P P
P N

 
 
    
 
 
   
 
 

Problem 2: A block weighing 500N just starts moving down a rough inclined plane
when supported by a force of 200N acting parallel to the plane in upward direction.
The same block is on the verge of moving up the plane when pulled by a force of 300N
acting parallel to the plane. Find the inclination of the plane and coefficient of friction
between the inclined plane and the block.
0V 
500.cosN 
1 .500cosF N   

30
1
0
200 500.sin
200 .500cos 500.sin
H
F 
  

 
  

(1)
2
0
500.cos
.500.cos
V
N
F N

  


 

2
0
500sin 300
500sin .500cos 300
H
F
  

 
  

(2)
Adding Eqs. (1) and (2), we get
500 = 1000. sinθ
sin θ = 0.5
θ = 30˚
Substituting the value of θ in Eq. 2,
500sin30 .500cos30 300 
50
0.11547
500cos30
  

31
Parallel forces on a plane
Like parallel forces: Coplanar parallel forces when act in the same direction.
Unlike parallel forces: Coplanar parallel forces when act in different direction.
Resultant of like parallel forces:
Let P and Q are two like parallel forces act at points A and B.
R = P + Q
Resultant of unlike parallel forces:
R = P - Q
R is in the direction of the force having greater magnitude.
Couple:
Two unlike equal parallel forces form a couple.
The rotational effect of a couple is measured by its moment.
Moment = P × l
Sign convention: Anticlockwise couple (Positive)
Clockwise couple (Negative)
P
R
Q
A B
P
R
Q
A
B
P
P
A
Bl

32
Problem 1 : A rigid bar CABD supported as shown in figure is acted upon by two
equal horizontal forces P applied at C and D. Calculate the reactions that will be
induced at the points of support. Assume l = 1.2 m, a = 0.9 m, b =0.6 m.
0V 
a bR R
Taking moment about A,
(0.9 0.6)
1.2
0.25 ( )
0.25 ( )
a b
b
b
b
a
R R
R l P b P a
P
R
R P
R P

    

 
  
  
Problem 2: Owing to weight W of the locomotive shown in figure, the reactions at the
two points of support A and B will each be equal to W/2. When the locomotive is
pulling the train and the drawbar pull P is just equal to the total friction at the points of
contact A and B, determine the magnitudes of the vertical reactions Ra and Rb.
0
a b
V
R R W

 

Taking moment about B,

33
0
2
. .
2
. .
2
. .
2
B
a
a
b a
b
b
M
R a P b W a
W a P b
R
a
R W R
W a P b
R W
a
W a P b
R
a

    

 
  
 
   
 

 

Problem 3: The four wheels of a locomotive produce vertical forces on the horizontal
girder AB. Determine the reactions Ra and Rb at the supports if the loads P = 90 KN
each and Q = 72 KN (All dimensions are in m).
0
3
3 90 72
342
0
9.6 90 1.8 90 3.6 90 5.4 72 8.4
164.25
177.75
a b
a b
a b
A
b
b
a
V
R R P Q
R R
R R KN
M
R
R KN
R KN

  
    
  

        
 
 


Problem 4: The beam AB in figure is hinged at A and supported at B by a vertical
cord which passes over a frictionless pulley at C and carries at its end a load P.
Determine the distance x from A at which a load Q must be placed on the beam if it is
to remain in equilibrium in a horizontal position. Neglect the weight of the beam.

34
FBD
OR
0
.
AM
S l Q x
P l
x
Q

  
 

Problem 5: A prismatic bar AB of weight Q = 44.5 N is supported by two vertical
wires at its ends and carries at D a load P = 89 N as shown in figure. Determine the
forces Sa and Sb in the two wires.
Q = 44.5 N
P = 89 N
0
89 44.5
133.5
a b
a b
a b
V
S S P Q
S S
S S N

  
   
  


35
0
4 2
4 2
89 44.5
4 2
44.5
133.5 44.5
89
A
b
b
b
b
a
a
M
l l
S l P Q
P Q
S
S
S
S
S N

    
  
  
 
  
 

Centre of gravity
Centre of gravity: It is that point through which the resultant of the distributed gravity
force passes regardless of the orientation of the body in space.
 As the point through which resultant of force of gravity (weight) of the body acts.
Centroid: Centrroid of an area lies on the axis of symmetry if it exits.
Centre of gravity is applied to bodies with mass and weight and centroid is applied to
plane areas.
c i i
c i i
x A x
y A y




1 1 2 2
1 2
1 1 2 2
1 2
c
c
A x A x
x
A A
A y A y
y
A A






Moment of area
Total area
.
.
c c
c
c
x y
x dA
x
A
y dA
y
A
 





36
Problem 1: Consider the triangle ABC of base ‘b’ and height ‘h’. Determine the
distance of centroid from the base.
Let us consider an elemental strip of width ‘b1’ and thickness ‘dy’.
1
1
1 1
AEF ABC
b h y
b h
h y
b b
h
y
b b
h
 

 
 
   
 
 
   
 

Area of element EF (dA) = b1×dy
1
y
b dy
h
 
  
 
.
c
y dA
y
A


0
0
2 3
2
. 1
1
.
2
2 3
1
.
2
2
2 3
2
6
3
2 3
h
h
y
yb dy
h
b h
b
b h
h h
h
h
h
h
y y
h
 
 
 


 
  
 
 


 
 
 
Therefore, yc is at a distance of h/3 from base.

37
Problem 2: Consider a semi-circle of radius R. Determine its distance from diametral
axis.
Due to symmetry, centroid ‘yc’ must lie on Y-axis.
Consider an element at a distance ‘r’ from centre ‘o’ of the semicircle with radial width
dr.
Area of element = (r.dθ)×dr
Moment of area about x = .y dA
   
 
 
 
0 0
2
0 0
2
0 0
3
0 0
3
0
3
0
3
3
. . .sin
sin . .
. .sin .
.sin .
3
.sin .
3
cos
3
1 1
3
2
3
R
R
R
R
r d dr r
r dr d
r dr d
r
d
R
d
R
R
R






 
 
 
 
 

 


 
  
 

 
 






Moment of area
Total area
cy 

38
3
2
2
3
2
4
3
R
R
R




Therefore, the centroid of the semicircle is at a distance of
4
3
R

from the diametric
axis.
Centroids of different figures
Shape Figure x y Area
Rectangle
2
b
2
d bd
Triangle 0
3
h
2
bh
Semicircle 0 4
3
R

2
2
r
Quarter circle 4
3
R

4
3
R

2
4
r
Problem 3: Find the centroid of the T-section as shown in figure from the bottom.
1
2

39
Area (Ai) xi yi Ai xi Ai yi
2000 0 110 10,000 22,0000
2000 0 50 10,000 10,0000
4000 20,000 32,0000
1 1 2 2
1 2
32,0000
80
4000
i i
c
i
A y A y A y
y
A A A

   


Due to symmetry, the centroid lies on Y-axis and it is at distance of 80 mm from the
bottom.
Problem 4: Locate the centroid of the I-section.
As the figure is symmetric, centroid lies on y-axis. Therefore, x = 0
2000 0 140 0 280000
2000 0 80 0 160000
4500 0 15 0 67500
1 1 2 2 3 3
1 2 3
59.71i i
c
i
A y A y A y A y
y mm
A A A A
 
  
 

Thus, the centroid is on the symmetric axis at a distance 59.71 mm from the bottom.
Problem 5: Determine the centroid of the composite figure about x-y coordinate. Take
x = 40 mm.
A1 = Area of rectangle = 12x.14x=168x2
A2 = Area of rectangle to be subtracted = 4x.4x = 16 x2

40
A3 = Area of semicircle to be subtracted =
 
22
24
25.13
2 2
xR
x

 
A4 = Area of quatercircle to be subtracted =
 
22
24
12.56
4 4
xR
x

 
A5 = Area of triangle = 21
6 4 12
2
x x x  
A1 = 268800 7x = 280 6x =240 75264000 64512000
A2 = 25600 2x = 80 10x=400 2048000 10240000
A3 = 40208 6x =240 4 4
3
x


=67.906
9649920 2730364.448
A4 = 20096 4 4
10 4
3
492.09
x
x x

 
  
 

4 4
8 4
3
412.093
x
x x

 
  
 

9889040.64 8281420.926
A5 = 19200 6
14 16
3
x
x x 
= 640
4
53.33
3
x

12288000 1023936
1 1 2 2 3 3 4 4 5 5
1 2 3 4 5
326.404c
A x A x A x A x A x
x mm
A A A A A
   
 
   
1 1 2 2 3 3 4 4 5 5
1 2 3 4 5
219.124c
A y A y A y A y A y
y mm
A A A A A
   
 
   
Problem 6: Determine the centroid of the following figure.
A1 = Area of triangle = 21
80 80 3200
2
m  
A2 = Area of semicircle =
2 2
2
2513.274
8 2
d R
m
 
 
A3 = Area of semicircle =
2
2
1256.64
2
D
m



41
3200 2×(80/3)=53.33 80/3 = 26.67 170656 85344
2513.274 40 4 40
16.97
3
 
 
100530.96 -42650.259
1256.64 40 0 50265.6 0
1 1 2 2 3 3
1 2 3
49.57c
A x A x A x
x mm
A A A
 
 
 
1 1 2 2 3 3
1 2 3
9.58c
A y A y A y
y mm
A A A
 
 
 
Problem 7: Determine the centroid of the following figure.
A1 = Area of the rectangle
A2 = Area of triangle
A3 = Area of circle
30,000 100 75 3000000 2250000
3750 100+200/3
= 166.67
75+150/3
=125
625012.5 468750
7853.98 100 75 785398 589048.5
1 1 2 2 3 3
1 2 3
1 1 2 2 3 3
1 2 3
86.4
64.8
i i
c
i
i i
c
i
A x A x A x A x
x mm
A A A A
A y A y A y A y
y mm
A A A A
 
  
 
 
  
 





42
Numerical Problems (Assignment)
1. An isosceles triangle ADE is to cut from a square ABCD of dimension ‘a’.
Find the altitude ‘y’ of the triangle so that vertex E will be centroid of
remaining shaded area.
2. Find the centroid of the following figure.
3. Locate the centroid C of the shaded area obtained by cutting a semi-circle of
diameter ‘a’ from the quadrant of a circle of radius ‘a’.
4. Locate the centroid of the composite figure.
Module –II

43
Truss/ Frame: A pin jointed frame is a structure made of slender (cross-sectional
dimensions quite small compared to length) members pin connected at ends and
capable of taking load at joints.
Such frames are used as roof trusses to support sloping roofs and as bridge trusses to
support deck.
Plane frame: A frame in which all members lie in a single plane is called plane frame.
They are designed to resist the forces acting in the plane of frame. Roof trusses and
bridge trusses are the example of plane frames.
Space frame: If all the members of frame do not lie in a single plane, they are called
as space frame. Tripod, transmission towers are the examples of space frames.
Perfect frame: A pin jointed frame which has got just sufficient number of members
to resist the loads without undergoing appreciable deformation in shape is called a
perfect frame. Triangular frame is the simplest perfect frame and it has 03 joints and
03 members.
It may be observed that to increase one joint in a perfect frame, two more members are
required. Hence, the following expression may be written as the relationship between
number of joint j, and the number of members m in a perfect frame.
m = 2j – 3
(a) When LHS = RHS, Perfect frame.
(b) When LHS<RHS, Deficient frame.
(c) When LHS>RHS, Redundant frame.
Assumptions
The following assumptions are made in the analysis of pin jointed trusses:
1.The ends of the members are pin jointed (hinged).
2.The loads act only at the joints.
3.Self weight of the members is negligible.
Methods of analysis
1.Method of joint
2.Method of section

44
Problems on method of joints
Problem 1: Find the forces in all the members of the truss shown in figure.
tan 1
45



  
Joint C
1 2 cos45S S
1 40S KN  (Compression)
2 sin 45 40S 
2 56.56S KN  (Tension)
Joint D
3 40S KN (Tension)
1 4 40S S KN  (Compression)
Joint B
5 3 2
0
sin 45 sin 45
V
S S S

 


45
5 113.137S KN  (Compression)
Resolving horizontally,
6 5 2
6
0
cos45 cos45
113.137cos45 56.56cos45
H
S S S
S

 
  

6 120S KN  (Tension)
Problem 2: Determine the forces in all the members of the truss shown in figure and
indicate the magnitude and nature of the forces on the diagram of the truss. All
inclined members are at 60˚ to horizontal and length of each member is 2m.
Taking moment at point A,
0
4 40 1 60 2 50 3
77.5
A
d
d
M
R
R KN

      
 

Now resolving all the forces in vertical direction,
0V 
40 60 50
72.5
a d
a
R R
R KN
   
 
Joint A
1
0
sin 60a
V
R S

 

12
0
cos60
H
S S

 

Ra

46
Joint D
0V 
7 sin 60 77.5S 
0H 
6 7 cos60S S
Joint B
1 3
0
sin 60 cos60 40
V
S S

 

4 1 3
4
0
cos60 cos60
37.532cos60 83.72cos60
H
S S S
S

 
  

Joint C
5 7
0
sin 60 50 sin 60
V
S S

 


Em notes

More Related Content

What's hot (20)

Similar to Em notes (20)

Recently uploaded (20)

Em notes