![Flow Chart for Load Flow Problem using UPFC
D efine X k, SB
rm ax, Initial SS
Calc ulate
X s=Xk.rm ax.SB /Ss
Perform load flow
=[0:10:360]
? Is Load flow
requirem ent is fulfilled
Calc ulate Pco n v2,
Qconv 2, Sco n v2
?
Adjust the param eter
w .r.t load flow results
End
Is UPFC param eters are
w ithin the results
Y
N
Y
N](https://image.slidesharecdn.com/unitiv-240830061907-0ff87113/85/EMERGING-FACTS-DEVICE-CONTROLLERS-Unit-IV-ppt-40-320.jpg)
EMERGING FACTS DEVICE CONTROLLERS Unit IV.ppt
- 1. Unit IV EMERGING FACTS CONTROLLERS STATCOM UPFC
- 2. SVC
- 3. A basic TCSC module TCSC CONTROLLER A typical TCSC system.
- 4. It is a solid-state switching converter, capable of generating or absorbing independently controllable real and reactive power at its output terminals when it is fed from an energy source. STATCOM is considered as voltage-source converter that, from a given input of dc voltage, produces a set of 3-phase ac-output voltages, each in phase with and coupled to the corresponding ac system voltage through a relatively small reactance STATCOM - Static Synchronous Compensator
- 5. STATCOM can improves 1. the dynamic voltage control in transmission and distribution systems; 2. the power-oscillation damping in power-transmission systems; 3. the transient stability; 4. the voltage flicker control; and 5. the control of not only reactive power but also (if needed) active power in the connected line, requiring a dc energy source.
- 6. STATCOM structure 1. it occupies a small footprint, 2. it factory-built equipment, thereby reducing site work and commissioning time; 3. it uses encapsulated electronic converters, thereby minimizing its environmental impact. A STATCOM is similar to an ideal synchronous machine, which generates a balanced set of three sinusoidal voltages—at the fundamental frequency—with controllable amplitude and phase angle.
- 7. STATCOM power circuit Reactive Power Generation Magnitude Es>Et Generates reactive power Magnitude Es<Et Absorbs reactive power
- 8. If the amplitude of the output voltage is increased above that of the utility bus voltage, Et, then a current flows through the reactance from the converter to the ac system and the converter generates capacitive- reactive power for the ac system. If the amplitude of the output voltage is decreased below the utility bus voltage, then the current flows from the ac system to the converter and the converter absorbs inductive-reactive power from the ac system. If the output voltage equals the ac system voltage, the reactive-power exchange becomes zero, in which case the STATCOM is said to be in a floating state. In reactive power generation, the real power provided by the dc source as input to the converter must be zero. The primary need for the capacitor is to provide a circulating-current path as well as a voltage source. When supplying/absorbing Reactive Power
- 9. In practice, the semiconductor switches of the converter are not lossless, so the energy stored in the dc capacitor is eventually used to meet the internal losses of the converter, and the dc capacitor voltage diminishes. Hence by making the output voltages of the converter lag behind the ac-system voltages by a small angle (usually in the 0.1–0.2 degree range), the converter absorbs a small amount of real power from the ac system to meet its internal losses and keep the capacitor voltage at the desired level.
- 10. STATCOM power circuit with energy storage Real Power Generation Phase Es leads Et Generates real power Phase Es lags Et Absorbs real power
- 11. Adjusting the phase shift between the converter-output voltage and the ac system voltage can similarly control real-power exchange between the converter and the ac system. If the converter-output voltage is made to lead the ac-system voltage, then the converter can supply real power to the ac system from its dc energy storage. If its voltage lags behind the ac-system voltage, then the it absorb real power from the ac system for the dc system When supplying/absorbing Real Power
- 12. STATCOM can supply both the capacitive and the inductive compensation and is able to independently control its output current over the rated maximum capacitive or inductive range irrespective of the amount of ac-system voltage. That is, the STATCOM can provide full capacitive-reactive power at any system voltage—even as low as 0.15 pu. V-I Characteristic Maximum turn off capability of converter switches Junction temperature of the converter switches
- 13. The characteristic of a STATCOM reveals another strength of this technology: It is capable of yielding the full output of capacitive generation almost independently of the system voltage. Hence it supports the system voltage during and after faults where voltage collapse would otherwise be a limiting factor. The maximum attainable transient overcurrent in the capacitive region is determined by the maximum current turn-off capability of the converter switches. In the inductive region, the converter switches are naturally commutated;
- 14. Unified Power Flow Controller (UPFC)
- 15. Unified Power Flow Controller (UPFC): A combination of static synchronous compensator (STATCOM) and a static series compensator (SSSC) which are coupled via a common dc link, to allow bidirectional flow of real/reactive power between the series output terminals of the SSSC and the shunt output terminals of the STATCOM. STATCOM SSSC
- 16. STATCOM Operation Reactive Power Generation Magnitude Es>Et Generates reactive power Magnitude Es<Et Absorbs reactive power Real Power Generation Phase Es leads Et Generates real power Phase Es lags Et Absorbs real power
- 17. SSSC Operation If the injected voltage is in phase with the line current, then the voltage would exchange real power. On the other hand, if a voltage is injected in quadrature with the line current, then reactive power—either absorbed or generated—would be exchanged.
- 18. In-phase Voltage injection V 0 V V+ 0 V V- 0 V V V Here, reactive power control through voltage adjustment Quadrature Voltage injection V 90 V α α V- 90 V V+ 90 V Here, real power control through phase angle adjustment V V 0 V V
- 19. Inverter 2 SSSC Inverter 1 STATCOM UPFC operation Vpq 0<Vpq<Vpqmax Phase angle 0 to 360 degree
- 20. Operation of UPFC One VSC—converter 1—is connected in shunt with the line through a coupling transformer; the other VSC—converter 2—is inserted in series with the transmission line through an interface transformer. The dc voltage for both converters is provided by a common capacitor bank. The series converter is controlled to inject a voltage phasor, Vpq, in series with the line. Thereby the series converter exchanges both real and reactive power with the transmission line. The reactive power is internally generated/ absorbed by the series converter, the real-power generation. The shunt-connected converter 1 is used mainly to supply the real- power demand of converter 2, which it derives from the transmission line
- 21. Phasor Diagram for series voltage injection Various Power Function of UPFC Voltage regulation Series Compensation Phase Shifting V0+ 0 V V0- 0 V V0
- 22. Phasor Diagram for Series Compensation V0 V0 Vpq Vc Here, Vpq is the sum of a voltage regulating component V0 and a series compensation providing voltage component Vc that lags behind the line current by 90 degree. V0’ V0 – Voltage regulating components Vc – Series compensation providing voltage component Vc that lag behind the line current by 90.
- 23. Phasor Diagram for Phase shifting V0 V0 Vpq Vα V0’ In the phase-shifting process, the UPFC-generated voltage Vpq is a combination of voltage-regulating component V0 and phase- shifting voltage component Vα
- 24. All three foregoing power-flow control functions The controller of the UPFC can select either one or a combination of the three functions as its control objective, depending on the system equirements.
- 25. The UPFC operates with constraints on the following variables: 1. the series-injected voltage magnitude; 2. the line current through series converter; 3. the shunt-converter current; 4. the minimum line-side voltage of the UPFC; 5. the maximum line-side voltage of the UPFC; and 6. the real-power transfer between the series converter and the shunt converter
- 26. Modes of operation of UPFC
- 27. Shunt Converter (STATCOM) Control Mode Reactive Power Control Mode Automatic Voltage control mode Series Converter (SSSC) Control Mode Direct Voltage Injection Mode Bus Voltage regulation and control mode Phase angle regulation mode Automatic Power flow control mode
- 28. Shunt Converter Shunt Controller Series Converter Series Controller sh I ~ 1 ~ v Iqref Vdcref pq V ~ 2 ~ v 1 ~ v sh I ~ 1 ~ v 2 ~ v i ~ Vpqref Vdc i ~ UPFC Control Scheme for different modes of Operation v1ref
- 29. Reactive Power Control Mode Reference inputs are used to generate inductive and capacitive VAR request Shunt converter control converts the VAR reference into the corresponding shunt current request by adjusting the gate pulse of the converter. Automatic Voltage control mode Uses feed back signal v1 Shunt converter reactive current is automatically regulated to maintain transmission line voltage to reference value at the point of connection.
- 30. Direct Voltage Injection Mode Simply generates Vpq with magnitude and phase angle requested By reference input. Vpq in phase with V voltage magnitude control Vpq quadrature with V real power control Bus Voltage Regulation Mode Vpq is kept in phase with v1 angle, its magnitude is controlled to maintain the magnitude output bus voltage v2 at the given reference value. Phase Angle Regulation Mode Vpq is controlled w.r.t voltage magnitude v1. Hence v2 is phase shifted without any magnitude change relative to the angle specified by the vi reference value.
- 31. Automatic Power Flow Control Mode Magnitude and angle of Vpq is controlled so as to force a line current, that results in desired real and reactive power flow in the line. Vpq is determined automatically and continously by closed loop control system to ensure desired P and Q.
- 32. Modeling of UPFC for Load Flow Studies
- 33. Basic Power Flow Equations at any bus i is calculated using Load flow Studies
- 34. Fig. The UPFC electric circuit arrangement Series connected voltage source is modeled by an ideal series voltage Vse which is controllable in magnitude and phase, that is, Vse = r*Vk*ejζ where 0≤r ≤rmax and 0 ≤ ζ ≤360. Modeling of UPFC for Load Flow Studies
- 35. Series Connected Voltage Source Converter -SSSC Fig. Representation of the series connected voltage source where r and are the control variables of the UPFC.
- 36. The injection model is obtained by replacing the voltage source Vse by a current source in parallel with xs, The current source Iinj corresponds to injection powers Si and Sj which are defined by
- 37. Injection model of the series part (SSSC) of the UPFC Active and reactive power supplied by Converter 2 are distinguished as:
- 38. Having the UPFC losses neglected, Here, it is assumed that QCONV1 = 0. Consequently, the UPFC injection model is constructed from series connected voltage source model with the addition of power equivalent to PCONV 1 + j0 to node i. Assumption made in Load Flow Studies
- 39. Injection model of the UPFC where r and are the control variables of the UPFC.
- 40. Flow Chart for Load Flow Problem using UPFC D efine X k, SB rm ax, Initial SS Calc ulate X s=Xk.rm ax.SB /Ss Perform load flow =[0:10:360] ? Is Load flow requirem ent is fulfilled Calc ulate Pco n v2, Qconv 2, Sco n v2 ? Adjust the param eter w .r.t load flow results End Is UPFC param eters are w ithin the results Y N Y N
- 41. where xk- - Series transformer short circuit reactance SB - The system base power SS - Initial estimation is given for the series converter rating power Rmax - Maximum magnitude of the injected series voltage xS - Reactance of the UPFC seen from the terminals of the series transformer - Between 0 and 360 degree