Energy management in agriculture revised lecture notes

Lecturer: Jean de Dieu IYAKAREMYE, Msc.

 Energy is the driver of growth
 Energy provides better living conditions to its
citizens
 Its growth has to be balanced and sustainable
 energy management and energy conservation
measures are: eco-friendly, minimum
pollution and carbon emission

 The fundamental goal of energy management
is: produce goods, provide services with the
least cost and the least environment effect
 The definition of energy management is:“The
judicious and effective use of energy to
maximise profits (minimise costs) and
enhance competitive positions”.

Objectives:
 To achieve and maintain optimum energy
procurement and utilization, throughout the
organization
 To minimize energy costs / waste without
affecting production, comfort and quality. To
minimize the environmental effects.

 Energy in any form is a scarce commodity and
most valuable resource
 As by prediction showing that the life
expectancy of world population will increase
so energy could, in the future, be in short
supply

There are two main sources of energy. They are conventional
and non conventional sources of energy.
i) Conventional sources of energy :- are wood, flowing water and
fossil fuels (coal, petroleum, natural gas).
ii) Non conventional sources of energy :- are solar energy, wind
energy, biomass energy, ocean energy (tidal energy, wave
energy,
ocean thermal energy), geothermal energy, nuclear energy etc.
 Some sources of energy are renewable like sun, wind, flowing
water, ocean, wood, biomass etc.
 Some sources of energy are non renewable like coal,
petroleum and natural gas.

a) Fossil fuels :- are fuels formed inside the earth from the
remains of plants and animals after millions of years. The
fossil fuels are coal, petroleum and natural gas. Fossil
fuels are non renewable sources of energy so they
should be conserved and used judiciously.
Disadvantages of fossil fuels :-
i) Burning of fossil fuels release gases and harmful particles
which causes air pollution.
ii) Burning of fossil fuels release acidic oxides of sulphur and
nitrogen which causes acid rain which is harmful for living
organisms, affects soil and water, causes damage to buildings,
corrosion of metals etc.
iii) Burning of fossil fuels release a large amount of carbon
dioxide gas which increases the temperature of the atmosphere
and causes global warming (green house effect).

Energy management in agriculture revised lecture notes

b) Thermal power plants :
 In thermal power plants the heat energy produced
by burning fossil fuels like coal, petroleum or
natural gas is used to heat water and change it
into steam which rotates the turbines of
generators to produce electricity.
c) Hydro power plants :
 In hydro power plants water from rivers are stored
by constructing dams. The water from the dam
flows down through pipes and rotates theturbines
of generators to produce electricity.

Advantages of hyropower:
i) Flowing water is a renewable source of energy.
ii) The electricity produced does not cause
pollution.
iii) The water stored in dams can also be used to
control floods and for irrigation.
Disadvantages of hydropower:
i) The initial cost is high.
ii) Large areas of land gets submerged and the
decomposition of vegetation produces methane gas
which is a green house gas.
iii) It causes displacement of people from large
areas of land.

d) Biomass energy :
 The waste materials and dead parts of living
things are called biomass. Eg :- wood, animal
dung, vegetable waste, agricultural waste,
sewage etc. Biomass is decomposed by
anaerobic microorganisms to produce biogas.
Biogas is a mixture of gases containing
methane, carbon dioxide, hydrogen and
hydrogen sulphide.

Biogas plant :
The biogas plant has a large underground tank
made of bricks and cement. The lower part is the
digester and the upper part has a dome with a gas
outlet. On one side of the tank above the ground is
a mixing tank and on the other side is an overflow
tank.
Animal dung is mixed with water in the mixing
tank and the slurry is sent into the digester. In the
digester the slurry is decomposed by anaerobic
microorganisms and after a few days biogas is
produced.
The gas is taken out through the gas outlet and
used for heating and lighting purposes. The slurry
left behind is rich in nitrogen and phosphorus and
is used as manure for crops.

e) Wind energy :
Wind energy is used in wind mills which converts
the kinetic energy of the wind into mechanical or
electrical energy.
The kinetic energy of wind can be used to do:
 mechanical work like lifting water from wells or
grinding grains in flour mills.
 It can also be used to rotate the turbines of
 A single wind mill produces only a small amount
of electricity.
 So a large number of wind mills in a large area
are coupled together to produce more electricity
in wind energy farms.

Advantages :
i) It is a renewable source of energy.
ii) It does not cause pollution.
iii) The recurring cost is less.
Disadvantages :
i) Wind is not available at all times.
ii) It requires a large area of land.
iii) A minimum wind speed of 15 km/h is
required.

a) Solar energy :
Solar energy is the energy obtained from the sun in
the form of heat and light. The heat energy is used
in solar heating devices like solar cooker, solar
water heater, solar furnaces etc.
The light energy is used in solar cells.
i) Solar cooker :
The box type solar cooker has an insulated box
painted black inside.
It is covered by a glass plate which allows heat to
enter inside but does not allow heat to escape out.
It has a mirror to reflect more sunlight into the box.
The food to be cooked is kept in containers inside
the box It can produce a temperature of 100° to
140°.

ii) Solar water heater :
A solar water heater has an insulated box
painted black inside with a system of copper
tubes. It is covered with a glass plate which
allows heat to enter inside but does not allow
heat to escape out. When water flows through
the copper tube it absorbs heat and becomes
hot.

iii) Solar cells :-
Solar cell is a device which converts solar energy into electrical
energy.
Solar cells are made from semi conductors like silicon,
germanium, gallium etc.
A single solar cell produces a voltage of about
 0.5 to 1 V and produces about 0.7 W electricity.
 So several solar cells are arranged in a solar panel to produce
more electricity.
Advantages :
i) It uses renewable source of energy.
ii) It produces electricity which does not cause pollution.
iii) It can be used in remote areas where there is no power
supply.

Disadvantages of solar cells:
i) It uses a special grade of silicon which is
expensive.
ii) Since silver is used for connecting the cells
together it is more expensive.
iii) The current produced is DC and to convert it
to AC increases the cost.

b) Energy from the sea :
Energy from the sea is obtained in three different forms. They
are
Tidal energy, Sea wave energy and Ocean thermal energy.
i) Tidal energy :
The periodic rise and fall of sea level due to gravitational
attraction of the moon causes tides.
A dam is constructed at a narrow opening
between the land and sea.
The movement of water during high tide and low tide can be
used to rotate the turbines of generators to produce
electricity.
ii) Sea wave energy :-
 When strong wind blows over the sea it produces huge
waves.
 The kinetic energy of the moving waves can be used to
rotate the turbines of generators to produce electricity.

iii) Ocean thermal energy :
There is a temperature difference between the
warm surface water and the cold water at the
bottom of the oceans.
This difference is about 20°C. The warm surface
water is used to boil liquid ammonia and the
vapour is used to rotate the turbines of
The cold water from the bottom is then
pumped up to cool the vapour back to liquid.

 The deeper regions of the earth’s crust is very
hot.
 This heat melts rocks and forms magma.
 The magma moves up and collects below at
some places called Hot spots. The
underground water in contact with hot spot
gets heated into steam at high pressure.
 By drilling holes into hot spots the steam
coming out can be used to rotate turbines of

d) Nuclear energy :
Nuclear energy is the energy is the energy released during nuclear
reactions.
During nuclear reactions some mass is converted into energy and so a
very
large amount of energy is produced during nuclear reactions.
Nuclear reactions are of two types. They are Nuclear fission and nuclear
fusion.
i) Nuclear fission : is a nuclear reaction in which the nucleus of a heavy
atom like uranium, plutonium, etc. splits into smaller nuclei with the
release of a large amount of energy. It is used to make atom bombs and
to produce electricity.
In a nuclear power plant the heat energy produced by a controlled
nuclear fission chain reaction is used to produce steam which rotates
the turbines of generators to produce electricity.

ii) Nuclear fusion :- is a nuclear reaction in which small nuclei
fuse together to form a heavier nucleus with the release of a
very large amount of energy. The energy of sun is produced
by the fusion of hydrogen nuclei to form helium nucleus.
It is also used to make the hydrogen bomb.
Advantages of nuclear energy :
i) It produces a very large amount of energy per unit mass
than any other
source of energy.
ii) If safety measures are taken, it is more environment
friendly than fossil fuels.
Disadvantages of nuclear energy :
i) The cost of a nuclear reactor is very high.
ii) The availability of nuclear fuel is limited.
iii) Nuclear reactors produce harmful nuclear wastes which is
difficult to dispose.

 This Chapter looks specifically at the
agricultural sector and its energy inputs. It is
useful to consider three entry levels for
interventions as a means of examining both
the energy needs for agriculture and the
requirements for rural energy services in
developing countries.
 These three levels are based on the "energy
ladder" approach. For agriculture, the three-
stage evolution can be considered as follows:

 basic human work for tilling, harvesting and
processing, together with rain-fed irrigation,
none of which involve an input from an external
fuel source;
 then the use of animal work to provide various
energy inputs;
 finally, the application of renewable energy
technologies such as wind pumps, solar dryers
and water wheels, together with modern
renewable and fossil fuel based technologies for
motive and stationary power applications, and for
processing agricultural products.

For rural energy, the needs of poor people can be
considered at the following three levels:
 energy for basic survival in cooking, lighting and
space heating using traditional biomass fuels;
 then as people move up from subsistence,
alternatives to traditional biomass fuels in these
applications such as kerosene and LPG;
 finally, the role of enhanced energy services in rural
areas using modern renewable energy and fossil
fuels, for example in providing energy for small
electrical appliances (e.g. lighting and radio) and the
provision of community facilities (e.g. street lighting,
water pumping, power for health centres and
schools).

 In both household and economic activities,
the "energy ladder" follows and influences the
"economic ladder".
 Attempts to alleviate poverty and to promote
rural economic development and food
security must be accompanied with efforts to
promote the key role of energy, not simply as
a goal in itself but as a vital component of
these attempts.

 Table 2.1 lists items in the conceptual framework relating
the level of household income and the types or sources of
energy services adopted by rural populations (DFID, 1999).
The framework includes household, agriculture, small-
scale rural industry and transport end-use requirements,
and is based on empirical evidence. It illustrates the
progression to modern fuels as income rises, and is based
on empirical evidence gathered by the World Bank and
other agencies. The data show that rural people choose to
spend a significant proportion of their incomes on a better
source of energy if they have access (World Bank, 1995).
 The table shows how opportunities generally increase and
the efficiency of energy utilization also increases, while the
negative impacts of energy use decrease with rising
household incomes.

 It can be seen that woodfuel still plays an
important role for households even at higher
income levels. In agriculture and industry, diesel
engines and electricity replace human and animal
work; where rural electrification is not available
or is too costly, diesel generators may be used
instead.
 Wind pumping for water extraction from wells,
together with mini-hydro and, more recently, PV
systems for small-scale electricity supplies for
homes, farms and community buildings are
possible renewable energy options.
 The use of these options may appear in future
empirical evidence.

Table 2.1: Levels of household income and energy services
End use Household income
Low Medium High
Household
Cooking Wood, residues, dung Wood, charcoal, dung, kerosene,
biogas
Wood, charcoal, coal, kerosene,
biogas, LPG, electricity
Lighting Candles and kerosene Candles, kerosene, gasoline Kerosene, electricity, gasoline
Space heating Wood, residues, dung Wood, charcoal, dung Wood, charcoal, dung, coal
Other appliances Batteries (if any) Electricity, batteries Electricity, batteries
Agriculture
Tilling Human Animal Animal, gasoline, diesel
Irrigation Human Animal, wind pumps Diesel, electricity
Post-harvest processing Human, sun drying Animal, water mills, sun drying Diesel, electricity, solar drying
Rural Industry
Mechanical tools Human Human, animal Human, animal, diesel, electricity
Process heat Wood, residues Coal, charcoal, wood, residues Coal, charcoal, wood, kerosene,
residues
Transport
Motive power Human Human, animal Human, animal, diesel, gasoline

 Agriculture is itself an energy conversion process, namely the conversion
of solar energy through photosynthesis to food energy for humans and
feed for animals. Primitive agriculture involved little more than
scattering seeds on the land and accepting the scanty yields that
resulted.
 Modern agriculture requires an energy input at all stages of agricultural
production such as direct use of energy in farm machinery, water
management, irrigation, cultivation and harvesting. Post-harvest energy
use includes energy for food processing, storage and in transport to
markets. In addition, there are many indirect or sequestered energy
inputs used in agriculture in the form of mineral fertilizers and chemical
pesticides, insecticides and herbicides.
 Whilst industrialized countries have benefited from these advances in
energy availability for agriculture, developing countries have not been so
fortunate. "Energizing" the food production chain has been an essential
feature of agricultural development throughout recent history and is a
prime factor in helping to achieve food security.
 Developing countries have lagged behind industrialized countries in
modernizing their energy inputs to agriculture.

 Agriculture accounts for only a relatively small proportion
of total final energy demand in both industrialized and
developing countries8. In OECD countries, for example,
around 3-5% of total final energy consumption is used
directly in the agriculture sector. In developing countries,
estimates are more difficult to find, but the equivalent
figure is likely to be similar - a range of 4-8% of total final
commercial energy use.
 The data for energy use in agriculture also exclude the
energy required for food processing and transport by
agro-industries. Estimates of these activities range up to
twice the energy reported solely in agriculture. Definitive
data do not exist for many of these stages, and this is a
particular problem in analyzing developing country energy
statistics.

 In addition, the data conceal how effective
these energy inputs are in improving
agricultural productivity. It is the
relationships between the amounts and
quality of the direct energy inputs to
agriculture and the resulting productive
output that are of most interest.

 On a broad regional basis, there appears to
be a correlation between high per capita
modern energy consumption and food
production. Figure 2.1 shows data for daily
food intake per capita and the annual
commercial energy consumption per capita in
seven world regions (FAO, 1995)9.

Figure 2.1: Modern energy consumption and
food intake

 Whilst broad data on a regional basis conceal many differences
between countries, crop types and urban and rural areas, the
correlation is strong in developing countries, where higher
inputs of modern energy can be assumed to have a positive
impact on agricultural output and food production levels.
 The correlation is less strong in industrialized regions where
food production is near or above required levels and changes in
production levels may reflect changes in diet and food fashion
rather than any advantages gained from an increased supply of
modern energy.
 Looking more closely at energy use in specific crops,
comparisons of commercial energy use in agriculture for cereal
production in different regions of the world are listed in Table
2.2 (Stout, 1990). The relationship between commercial energy
input and cereal output per hectare for the main world regions is
also shown in Figure 2.2 (Stout, 1990)

 These data, whilst relatively old, indicate that developing countries use
less than half the energy input (whether in terms of energy per hectare
of arable land or energy per tonne of cereal) compared with
industrialized countries.
 However, this is not to say that developing countries are necessarily
more efficient in their use of energy for agricultural production.
 This energy statistic does not account for the quantity of human effort
used in developing countries for agriculture.
 In drawing conclusions, it is also important to consider the equity and
sustainability considerations when comparing energy use data.
 Empirical evidence suggests that the availability of modern energy such
as petroleum fuels has proven to be essential in increasing the
productivity of the agricultural sector in industrialized countries.
 In terms of the energy used per agricultural worker, the differences are
even more dramatic, with developing countries using less than 5% of the
energy per agricultural worker compared with industrialized countries.
 An obvious difference between industrialized and developing countries
is the large numbers of agricultural workers per hectare in developing
countries compared with industrialized countries.

Table 2.2: Commercial energy use and cereal output (1982)
Region Energy per hectare of
arable land (kgoe/ha)
Energy per tonne of
cereal
(kgoe/t)
Energy per
agricultural
worker(kgoe/person)
Africa 18 20 26
Latin America 64 32 286
Far East 77 43 72
Near East 120 80 285
All developing
countries average
96 48 99
All industrialized
countries average
312 116 3294
World average 195 85 344

Figure 2.2: Cereal yield and energy input per hectare for the
main world regions10

 In general, those regions with higher energy consumption have
higher agricultural yields. However, the relationships between
energy input and agricultural output are also affected by the
varying ecological and environmental conditions around the
world; soil fertility and rain-fed water availability being prime
examples. Exact comparisons at the national level are, therefore,
not easily made, but it is possible to use energy inputs for
specific crops to gain further insights into the relationship
between energy use and agricultural productivity.
 As an example of this, a comparison between the commercial
energy required for rice and maize production by modern
methods in the United States, and transitional and traditional
methods used in the Philippines and in Mexico is shown in Table
2.3.
 These data show that the modern methods give greater
productive yields and are much more energy-intensive than
transitional and traditional methods (Stout, 1990).
 These methods include the use of fertilizer and other chemical
inputs, more extensive irrigation and mechanized equipment.

Table 2.3: Rice and maize production by modern, transitional
and traditional methods
Rice production Maize production
Modern
(United
States)
Transitional
(Philippines)
Traditional
(Philippines)
Modern
(United States)
Traditional
(Mexico)
Energy input
(MJ/ha)
64,885 6,386 170 30.034 170
Productive
yield (kg/ha)
5,800 2,700 1,250 5,083 950
Energy input
yield (MJ/kg)
11.19 2.37 0.14 5.91 0.18

 A further illustration of the relationship
between energy intensity and agricultural
productivity is given in Box 2. This presents a
case study of energy use in durum wheat
production in Tunisia (Myers, 1983). The
study showed that farms with the highest
energy input per hectare had the highest
production and lowest input per tonne of
production.

 Agriculture practices in many developing countries continue to be based
to a large extent on animal and human energy. Insufficient mechanical
and electrical energy is available for agriculture, and hence the potential
gains in agricultural productivity through the deployment of modern
energy services are not being realized.
 Agricultural energy demand can be divided into direct and indirect
energy needs.
 The direct energy needs include energy required for land preparation,
cultivation, irrigation, harvesting, post-harvest processing, food
production, storage and the transport of agricultural inputs and outputs.
 Indirect energy needs are in the form of sequestered energy in
fertilizers, herbicides, pesticides, and insecticides.
 Mankind has adapted a variety of resources to provide for energy in
agriculture. Animal draught power obtained through domestication of
cattle, horses and other animals has existed for over 8,000 years, the
water wheel is over 2,000 years old, and windmills were introduced over
1,000 years ago. Direct sun energy for drying and biomass fuels for
heating have also been prominent as agricultural energy inputs for
centuries.

 The bulk of direct energy inputs in developing
countries, particularly in the subsistence
agriculture sector, is in the form of human and
animal work. Human work has a limited output,
but humans are versatile, dextrous and can make
judgements as they work.
 This gives humans an advantage in skilled
operations such as transplanting, weeding,
harvesting of fruits and vegetables and working
with fibres.
 Water lifting and soil preparation need less skill
but more energy input

 A sustainable rate at which a fit person can
use up energy is around 250-300 W,
depending on climate and needing 10-30
minutes/hour rest.
 The efficiency of energy conversion is only
about 25%, with a maximum sustainable
power output of 75 W. Table 2.4 lists human
power consumption for various farming
activities (Carruthers and Rodriquez, 1992).

Table 2.4: Human power consumption for various farming
activities
Activity Gross power consumed (W)
Clearing bush and scrub/felling trees 400-600
Hoeing, planting 200-500
Ridging, deep digging 400-1000
Ploughing with draught animal 350-550
Driving 4 wheel tractor 150-300
Driving single axle tractor 350-650

 Animals provide transport of products, can pull implements
and lift water and are used in processing activities such as
cane crushing and threshing. The world population of draught
animals is estimated at over 400 million (WEC/FAO, 1999).
 Animal work can alleviate human drudgery and increase
agricultural production. Power output ranges from 200 W for a
donkey to over 500 W for a buffalo, and daily working hours
range from 4 hours for a donkey up to 10 hours for a horse.
 There are limitations on the performance of animals, especially
at times when they are needed most in the dry season with
feed, grazing and water in short supply.
 Implements used by animals can be pole-pull, chain-pull or
wheeled carriers.
 Table 2.5 lists power and energy characteristics of typical
farm animals in good condition (Carruthers and Rodriquez,
1992).

Table 2.5: Power and energy output of individual farm animals
Animal Typical
weight(kN)
Pull-weight
ratio
Power output (W) Energy output per
day (MJ)
Ox 4.5 0.11 450 10
Buffalo 5.5 0.12 520 9.5
Horse 4.0 0.13 500 18
Donkey 1.5 0.13 200 3
Mule 3.0 0.13 400 8.5
Camel 5.0 0.13 650 14

 It seems likely that both human and animal
work will continue to be used as agricultural
inputs for the foreseeable future in
developing countries.
 Efforts to support these farming traditions
include work on animal efficiency, which can
be improved through modernization of
equipment, better breeding and animal
husbandry, feeding and veterinary care, and
on improved designs of animal-drawn farm
equipment.

A transition to increased mechanization of farm
operations has been undertaken over a long period
of time.
Table 2.6 lists selected indicators of agricultural
mechanization using tractors and harvesters for
different world regions expressed in terms of
cropland area and numbers of agricultural workers
(WRI, 1994).
The data show a wide disparity in the degree of
mechanization between the different regions, with
Africa having the lowest level of mechanization.

Table 2.6: Selected indicators of agricultural mechanization
Africa Latin America Europe World
Total population 1990 (million) 643 294 509 5,295
1990 agricultural workforce
(million)
211 40 30 1481
Cropland
(million ha)
181 115 138 1,441
Tractors 544,000 1,125,000 10,384,000 26,411,000
Agricultural workers/tractor 387 36 3 56
Hectares/tractor 333 102 13 55
Harvesters 70,000 117,000 831,000 3,956,000
Agricultural workers/harvester 3,019 340 36 374
Hectares/harvester 2,599 980 166 364

 Tillage operations are used within arable farming systems, which
are often the operations with the highest energy requirements.
Mechanized soil tillage has in the past been associated with
increased soil fertility, due to the mineralization of soil nutrients;
it also allows higher working depths and speeds and the use of
implements such as ploughs, disc harrows and rotary cultivators.
This process leads in the long term to a reduction of soil organic
matter, and most soils degrade under long lasting intensive
arable agriculture with particularly detrimental effects on soil
structure.
 The process is dramatic under tropical climate conditions but
can be noticed all over the world.
 Reduction of mechanical tillage and promotion of soil organic
matter through permanent soil cover is an approach to reverting
soil degradation and other environmental impacts of
conventional agriculture, achieving at the same time a high
agricultural production level on truly sustainable basis. This
approach is described as `conservation agriculture' and replaces
mechanical soil tillage by `biological tillage'.

 In this approach, crop residues remaining on the soil surface
produce a layer of mulch which protects the soil from the
physical impact of rain and wind, and also stabilizes the soil
surface layers moisture content and temperature.
 This zone becomes a habitat for a number of organisms which
macerate the mulch, mix it with soil and assist its decomposition
to humus.
 Agriculture with reduced mechanical tillage is only possible when
soil organisms take over the task of tilling the soil.
 This leads to other implications regarding the use of chemical
inputs since synthetic pesticides and mineral fertilizers have to
be used in a way that does not harm soil life.
 Conservation agriculture can only work if all agronomic factors
are equally well managed11.

 It should also be noted that, whilst shifts from
human work to mechanized processes may offer
more efficient use of resources, and deliver
productive and economic benefits, the
agricultural sector does provide a source of paid
employment for rural people in developing
countries.
 A balance is often required between the socio-
economic benefits and the agricultural productive
benefits of changing the processes (and thereby
the energy inputs) involved.

 Fertilizers, and other chemical inputs to agriculture,
have proved important in the past in increasing food
production in all regions of the world.
 Mineral fertilizers, chemical pesticides, fungicides
and herbicides all require energy in their production,
distribution and transport processes.
 Fertilizers form the largest of these energy inputs to
agriculture, whilst pesticides are the most energy-
intensive agricultural input (on a per kg basis of
chemical).
 The need for insecticides and fungicides can,
however, be reduced through greater use of pest
control methods based on the principals of integrated
pest management.

 The energy contents of various agricultural
inputs12 are listed in Table 2.7, which show
illustrative values of the energy required for
manufacturing these products.
 Full life-cycle values (i.e. from extracting the
chemical raw material through to final delivery of
the manufactured product to the field) would
depend on several highly variable factors.
 These include the actual location of chemical raw
material supplies relative to the productive
facility, the ease of extraction, the chemical
manufacturing processes, and the distances
involved in transporting raw, semi-finished and
finished products.

Table 2.7: Energy content of agricultural inputs
Input Typical rate of
application
(kg/ha)
Sequestered
energy (MJ/kg)
Energy content of
crop produce
(MJ/ha)
Fertilizer Nitrogen 150 65 9,750
Phosphate 60 9 540
Potash 60 6 360
Insecticide 0.14 200 28
Herbicide 5 240 1,200
Fungicide 3 92 276
Seed 120 14 1,680

 By comparison with the energy content of mineral
fertilizer, the energy content of fresh manure is much
lower at around 0.35 MJ/kg.
 However, the amount of plant, human and animal
wastes available in developing countries that could
potentially be used for organic manure is several
times the consumption of chemical fertilizers in these
countries.
 The volume of fertilizer input to agriculture differs
markedly between regions of the world, as shown in
Table 2.8 (WRI, 1994). The data, which are broad
regional estimates, show that Africa and Latin
America use very low inputs compared with Asia and
Europe.

Table 2.8: Fertilizer input to agriculture (1990)
Average annual fertilizer use (kg/ha crop
land)
World 96
Africa 20
Asia 123
Europe 192
North and Central
America
87
Latin America 44

 Agricultural practices are, however, changing
throughout the world. In recent years,
diminishing returns from increased use of
fertilizers and pesticides have raised questions
about their role in the transition towards more
environmentally-sound agricultural practices.
 The main constraints in increasing organic
manure use are the large labour and skills
content required together with the need to
change cultural attitudes and the lack of mixed
livestock and crop husbandry.

 Energy is required for cooking most foods,
and for boiling water for drinking, washing
and for partial water purification. In small-
scale food cooking, many rural households
continue to rely on woodfuel.
 Figure 2.3 presents data on the efficiency of
various cooking fuels (World Bank, 1995).
 The data are derived from a combination of
the energy content of each fuel and the
efficiency with which the fuels are typically
burned for cooking in developing countries.

Figure 2.3: Energy efficiency of selected
cooking fuels

 Traditional biomass are generally much less efficient for
cooking than modern, commercially traded fuels such as
liquefied petroleum gas and kerosene.
 These fuels have higher energy values per unit of weight than
woodfuels, and are generally used in more efficient stoves.
 In addition, the level of heat output of kerosene stoves can be
adjusted, so making kerosene more convenient for preparing
a wide range of foods.
 Another versatile fuel is biogas, derived from digesters using
dung and farm residues, and both China and India have done
much to develop biogas and encourage its use among people
in rural areas. The least efficient fuels are agricultural
residues, but poor people are forced to use these fuels where
they are available in the local environment because they have
no cash cost.

 Improved cooking stove programmes have been a feature of
many rural energy interventions over the last 20 years (FAO,
1996a).
 Work has been carried out on establishing multi-sectoral support
and involvement, and integrating technology, dissemination and
financing.
 National standards on cooking and heating efficiency and
guidelines for stove programmes have been developed. Studies
have shown that the health and quality of life of both women and
children can be improved by improving access to biomass and
providing biomass stoves which are designed to be safer to use
in terms of reduced risk of burns, respiratory disease and eye
problems (World Bank, 1995).
 Indeed, the thrust of the current work on improved cooking
stoves has become one of reducing the adverse health impact of
traditional cooking methods rather than one of achieving
potential fuel savings or increasing stove energy efficiency.

 The agroprocessing industry transforms products originating
from agriculture into both food and non-food commodities.
Processes range from simple preservation (such as sun drying)
and operations closely related to harvesting, to the production,
by modern, capital-intensive methods of such articles as textiles,
pulp and paper.
 Upstream industries are engaged in the initial processing of
products, with examples such as rice and flour milling, leather
tanning, cotton ginning, oil pressing, saw milling and fish
canning.
 Downstream industries undertake further manufacturing
operations on intermediate products made from agricultural
materials.
 Examples are bread and noodle making, textile spinning and
weaving, paper production, clothing and footwear manufacture
and rubber manufacture13.

 An energy input is required in food processing,
as well as in packaging, distribution and storage.
Many food crops when harvested cannot be
consumed directly, but must pass through
several stages of processing as well as cooking in
order to be palatable and digestible.
 Raw meats, uncooked grains, vegetables and
even fruits require preparation and heating to
enhance their flavour, rendering their
components edible and digestible.
 The processing and cooking stages reduce
harmful organisms and parasites, which might
pose health hazards.

 Poorly handled and stored food can become spoiled
and contaminated. Food preservation usually requires
the application of heat to destroy micro-biological
agents, such as bacteria, yeast and mould.
 Pasteurization causes the inactivation of spoilage
enzymes and reduction of bacteria at temperatures
around 80-90oC.
 Heat sterilization can use atmospheric steam at
100oC for high-acid foods, and pressurized steam at
around 120oC for low acid foods. Other techniques
include dehydration to reduce moisture content,
pickling/smoking to reduce microbial activity,
fermentation, salting and freezing.

 Food transformation activities are generally
less energy-intensive and release less
CO2 and metal residues than most other
industrial activities per unit of product.
 As described in more detail below, agro-
processing industries, such as sugar mills,
can become not only energy self-sufficient
through the energy conversion of biomass
residues, but also electricity producers for
export to other users.

 The international community has agreed that a priority in
Agenda 21 should be promoting sustainable agriculture
and rural development (SARD) and one of the programme
areas [Chapter 14k in Agenda 21] is to encourage a rural
energy transition in order to enhance productivity (UNCED,
1992).
 The objectives of this programme area include initiating
the required transition by making available new and
renewable sources of energy and increasing the energy
inputs available for rural household and agro-industrial
needs.
 Rural programmes favouring sustainable development of
renewable energy sources and improved energy efficiency
are also called for in Agenda 21 in the programme area
dealing with protection of the atmosphere [Chapter 9b in
Agenda 21].

 CSD-8 in April 2000 included agriculture and
forests as the major economic sector for
discussion, and CSD-9 in April 2001 will
examine atmosphere and energy as sectoral
themes and energy and transport as
economic themes.
 There are clear links between these two
sessions of CSD.

 The international framework for action does,
therefore, exist. Nevertheless, it seems clear
from the data presented in this Chapter that
there is a wide disparity between energy inputs in
agriculture in industrialized countries with that in
developing countries and that this disparity is
hindering agricultural productivity gains.
 One consequence of this is that enhanced food
security is more difficult to achieve.
 This affects not only the quantity of food
produced, but also the quality - people are
forced to eat uncooked food or food that can
easily be cooked but which may not give full
nourishment.

 This situation is manifest in the general lack of an agricultural
component in rural energy development policies.
 Agriculture contributes significantly to economic and social
development, accounting for around 30% of developing country
GDP14, but energy provision for agriculture has not received the
attention that the sector deserves.
 The World Bank has observed (World Bank, 2000b) that most
energy policies in developing countries have traditionally focused
on large capital investments in the generation and transmission
of electricity, gas and petroleum products, so enabling the
commercial development of energy supply industries.
 These policies are designed mainly for the needs of industry,
transport and urban infrastructure, and thereby focus most
attention on urban populations, whilst rural populations (and to
some extent peri-urban populations) and their energy
requirements are frequently overlooked

 Even where there has been a focus on rural energy and
development and attention given to the scope for
improving energy services to rural populations, much of
the work has concentrated on the household use of
energy.
 For example, there have been many programmes to
expand the use of improved cooking stoves and to provide
households and community buildings with small amounts
of electrical power through the development of solar home
systems using PV technology.
 Whilst these PV programmes offer many benefits at the
household level, none of them have directly tackled the
energy supply problems in the agriculture sector (FAO,
2000a), and nor have they promoted income generating
activities. Such activities are the only way for rural people
to break out from the vicious circle of poverty15.

 FAO has been active in assisting developing countries to meet
their energy requirements in agriculture, forestry and fisheries as
a means of achieving sustainable rural development.
 An integrated approach to incorporating energy into rural and
agricultural planning has been promoted, together with the
increased use of modern energy technologies.
 Activities sponsored by FAO have included, for example, a
project in China, which integrated alcohol production from
sorghum with biogas, pyrolysis, solar and wind energy systems
(FAO, 1994).
 This work also examined energy conservation and the potential
of various renewable energy sources in specific farm activities.
The project is presently being expanded to produce ethyl tertiary
butyl ether (ETBE) from ethanol.
 ETBE is then mixed with gasoline and offers reduced air pollution
and CO2 emissions from transport. Trials are planned for
Shanghai and Shenyang.

 The 1996 Rome Declaration on World Food Security
reaffirmed the right of everyone to have access to
safe and nutritious food, consistent with the right to
adequate food and the fundamental right of everyone
to be free from hunger.
 FAO recently reviewed the state of food insecurity in
the world and identified that in the developing world,
790 million people do not have enough to eat (FAO,
2000b).Whilst there are many reasons for this
situation, there is scope for improved productivity
and food security by increasing energy inputs in rural
areas.
 The analysis in this Chapter shows, therefore, that
there is a clear rural energy gap in the agricultural
sector, which needs to be bridged.

 All agricultural production has to become
commercial to enable long-term food security; as
one of the prime inputs to agriculture, energy
plays a decisive role in attaining food security.
 Attempts to alleviate hunger and to promote
rural development and food security must be
accompanied by efforts to promote the key role
of energy, not as a goal in itself but as a vital
component of these attempts.
 In many cases, it seems that the low quality and
the meagre amounts of energy available for the
food production and supply chain are at the heart
of food security problems.

 The empirical evidence and examples presented earlier in
this Chapter indicate that it is possible to quantify the
extent of this gap in energy terms.
 However, if this gap were to be closed by an over-zealous
use of fossil fuels
 This solution would not offer a sustainable means of
tackling the energy gap problem.
 Development and deployment of renewable energy
systems together with improved end-use energy efficiency
techniques can provide an alternative means of helping to
bridge this gap. A large number of such energy
technologies are mature and commercially available, whilst
others still require further research or demonstration.
 Actions to invest in cost-effective systems and to develop
the most promising new technologies are needed.

 The recent moves towards opening world
markets to a much wider agricultural trade
will have an impact on energy requirements
in the agricultural sector.
 Greater international trade will encourage and
require more energy for processing primary
agricultural products closer to the source of
production in developing countries, then
transporting, storing and finally distributing
these products to industrialized countries.

 For example, horticultural products often
have a high added value and a transportation
and storage system between the farm and the
end market using a cold-chain or a controlled
modified atmosphere is needed to maintain
this value. Hence the new trade opportunities
point to additional energy intensive
applications developing in the agricultural
sector, so increasing the level of energy
demand in developing countries.

 Ways of measuring the sustainability of energy and
agriculture and in particular the benefits of improved energy
services for agriculture need to be established, so that
indicators of progress can be developed. For example,
current work on sustainability indicators could be adapted to
include energy and agriculture16.
 Such measures would assist the establishment of a bridge
between the rural energy and agricultural policy dimensions
so that agricultural energy needs can be included in overall
energy planning and policy formation.
 FAO has initiated work in this field and is developing energy
indicators of sustainable agriculture. A third linkage is
between the environmental dimension and energy use by
agriculture, and suitable indicators of this also need to be
developed.

 Energy problems and solutions for agriculture should always be
guided by local economic, environmental and social
considerations. Energy policy formation should bring together
national energy development policies with the locally perceived
priorities.
 There needs to be increased emphasis on non-fossil fuel
alternatives to the provision of energy services in agriculture in
developing countries (Best, 1997).
 These range from the modern renewable energy sources, such as
improved biomass conversion (including liquid biofuels, biogas,
gasification), solar energy (PV), wind and geothermal energy and
small-scale hydropower, to lower energy intensity industries,
material and energy recycling and better means of utilizing
traditional energy sources, such as improved cooking stoves.
 In addition, there needs to be improved energy efficiency in
mechanical equipment and in drying and separating operations.

 The agriculture sector can move towards a
path of greater sustainability through the
application of improved techniques and
practices such as conservation agriculture,
organic farming, protecting agro-biodiversity,
better water and soil management, and
integrated pest management and plant
nutrition.
 Where appropriate a greater level of
mechanization and improved food-
processing technologies are also important.

 The main challenge in the medium term for
energy in agriculture is to mobilize the changes
occurring in both the energy supply and the
agricultural sectors to the benefit of rural
livelihoods and communities.
 There is a danger that rural populations could be
left behind unless energy policies are directed
specifically on their needs.
 It seems clear from the analysis presented in this
Chapter that energy requirements should be
appropriately considered and integrated into
agricultural and rural development programmes.

8
Methodological limitations regarding the boundaries of data collection, statistical analysis and
definitions may mask the true picture. However, the basic assessments and propositions in this Chapter
remain valid.
9 The regions are (in ascending order of energy use per capita): Sub-Saharan Africa, South Asia, East Asia/Pacific, Latin America/Caribbean, Middle East/North Africa,
Europe, OECD.
10
The world regions used (in ascending order of energy per hectare of arable land) are: Africa, Latin
America, Far East, Near East, Eastern Europe, Asia, North America, Western Europe.
11
Additional information about the work of FAO in conservation agriculture can be found at
<http://www.fao.org/ag/ags/agse>.
12
Source: Data derived from Stout, 1990, and FAO statistics estimates. Additional data may be found
from the IFOAM web site <http://www.ifoam.org>.
13
Further information on FAO's work in the agroprocessing industry and economic development can be
found at http://www.fao.org/apps/advsearch/adv_search.asp.
14
Compared with 7-8% of GDP for industrialized countries; source: FAO, 1995.
15
Annex A.3 contains some additional findings from recent FAO work on the impact of PV systems in
rural development.
16
Annex A.1 contains some further details of the work on developing energy and agriculture indicators.
The web site <http://www.globenet.org/helio> also has additional information.

 Energy Conservation is the deliberate practice
or an attempt to save: electricity, fuel oil,
mechanical power, gas or any other
combustible material
 Energy Conservation is to be able to put to
additional use for additional productivity
without spending any additional resources or
money.

 Energy conservation is achieved when: growth
of energy consumption is reduced,
measured in physical terms
 Energy conservation can be the result of
several processes or developments( increase
of productivity or technology)
 Energy conservation and Energy Efficiency are
separate, but related concepts.

 Energy efficiency is achieved when energy
intensity in a specific product, process or
area of production or consumption is reduced
without effecting output, consumption or
comfort levels.
 Promotion of energy efficiency will contribute
to energy conservation and is therefore an
integral part of energy conservation
promotional policies.

 For example, replacing traditional light bulbs
with Compact Fluorescent Lamps (CFL) (which
use only 1/4th of the energy to same light
output). Light Emitting Diode (LED) lamps are
also used for the same purpose.

i) Minor ECOs
 These are simple, easy to implement, and
require less investment implementation time.
These may correspond to stopping of:
- leakage points, avoiding careless waste,
lapses in housekeeping
- and maintenance etc.

ii) Medium ECOs
 These are more complex, and required
additional investment and moderate
implementation time.
For example, replacement of existing
household appliances or any other energy
source by new energy efficient ones.

iii) Major ECOs
 These provide significant energy saving. They
are complex and demand major investment
and long implementation periods.
For example, replacement or major renovation
of old buildings, machineries etc.

 Psycho-social (people do not like to change:
social taboos and traditions)
 Economic (replacementis often costly).

 Is the key of energy conservation and
management
 Energy audit is defined as "The Verification,
Monitoring and Analysis of use of energy
including: submission of Technical Report
containing recommendations for improving
energy efficiency with cost benefit analysis,
and an action plan to reduce energy
consumption".

 Energy Accounting
Energy accounting simply means record of
energy used in an establishment for comparison
against a budget or another standard of
performance.

 Systematic Approach To Decision Making
Energy Audit is the key to systematic approach
for decision making in the areas of energy
management. It attempts to balance the total
energy inputs with its use and serves to identify
all the energy streams in a facility. It quantities
the energy usage according to its discrete
functions.

 Effective Tool for Energy Management
Energy Audit is an effective tool in defining and
pursuing comprehensive energy management
programme. In this field also, the basic
functions of management like planning,
decision making, organizing and controlling,
apply equally as in any other management
subject.

 Ways of Usage of Energy
Energy Audit will help to understand more
about the ways energy and fuel are used in any
establishment, and help in identifying the areas
where waste can occur and where scope for
improvement exists.

 Construction and Stream Lining
The Energy Audit would give a positive
orientation to the energy cost reduction,
preventive maintenance and quality control
programme which are vital for production and
utility activities/.

 Ideas and Feasible Solution
In general, Energy Audit is the translation of
conservation ideas into realities, by blending technically
feasible solutions with economic and other
organizational considerations within a specified time
frame.
 In brief energy audit is an in-depth study of a facility
to determine how and where energy is being used or
converted from one form to another, to identify
opportunities to reduce energy usage, to evaluate the
economics and technical practicability of
implementing these reductions and to formulate
prioritized recommendations for implementing
measures to save energy.

 Comparison of energy utilization of different
crops
 Energy accounting of a specific crop from
tillage to harvesting.
 Energy Audit in a small scale village industry
 Energy accounting of a brick kiln
 Energy accounting of flour mill
 Energy Audit in ISAE Farm

 Students will be given different papers to
analyze and submit the findings
 Three types of papers are given

1. Explain how conventional energy sources
are used in Rwandan Agriculture and give 5
examples
2. Describe Non conventional energy sources
use in Rwandan Agriculture and give 5
examples
3. What are the most used energy sources in
Rwandan Agriculture? Why is it so?
4. In your own words define “Energy
management for Agriculture”

Read the Paper and understand it before answering
these following questions
Paper Title: Energy Efficiency of Conventional,
Organic, and Alternative Cropping Systems for
Food and Fuel at a Site in the U.S. Midwest( by S I
E G L I N D E S . SN A P P , A N D G . P H I L I P R O
B E R T S O N )
1. What are the objectives of this study?
2. Describe the need of this study
3. Discuss briefly on materials and methods used
4. Compare energy efficiencies in 5 systems which
are discussed in this paper

Paper Title: Impacts of organic farming on
efficiency of energy use in Agriculture (by David
Pimentel)
1. Write down the main objectives of this paper
2. What are the main differences in energy
requirement between conventional and organic
farming?
3. What are the benefits of organic farming over
conventional farming?
4. Why organic farming is preferred?

Paper Title: Energy use pattern analyses of
greenhouse vegetable production (By M. Canakci, I.
Akinci)
1. Describe the objectives of this study
2. What is the relationship between energy input
and crop yield on different crops discussed in
this paper.
3. Briefly discuss materials and methods used in
this paper.
4. Which plant does not require much energy for
production?

Energy management in agriculture revised lecture notes

More Related Content

What's hot (20)

Similar to Energy management in agriculture revised lecture notes (20)

More from IYAKAREMYE Jean De Dieu (9)

Recently uploaded (20)

Energy management in agriculture revised lecture notes