FFR with St. Jude System
Download as PPTX, PDF15 likes1,874 views
FFR is a technique used during coronary catheterization to measure pressure differences across a coronary artery stenosis to determine if it is restricting blood flow. FFR provides an invasive test to estimate the effects of a narrowed blood vessel in real-time without providing information on plaque morphology. Medications like adenosine are administered to increase the heart's workload and detect ischemia during FFR testing. Significant stenoses are considered less than 0.80 on the FFR scale while readings above 0.80 are not generally deemed significant obstructions.
FFR with St. Jude System
- 1. ……………....... Muhammad Naveed Saeed Cath Lab Tech. January 7, 2016
- 3. Technique used in coronary catheterization to measure pressure differences across a coronary artery stenosis (narrowing, usually due to atherosclerosis) to determine the likelihood that the stenosis impedes myocardial ischemia.
- 6. FFR assess of lesion severity. FFR invasive test and allows real-time estimation of the effects of a narrowed vessel. No plaque morphology information. physical exercise or some intravenous medication is to increase the workload and oxygen demand of the heart muscle, and ischemia is detected using ECG changes or Nuclear imaging.
- 7. • Adenosine: 6mg/500cc NS (12mcg/cc) • IC boluses: ○ –60 mcg (5 cc) ○ –96 mcg (8 cc) ○ –120 mcg (10 cc) • IV drip 140 mcg/Kg/Min
- 8. • http://www.cathlabdigest.com/article/return-ic-adenosine-ffr-history-dose- technique Issue number: volume 23 - issue 12 - December 2015
- 9. Significant <0.80 Grey Scale 0.8 Non Significant > 0.8
- 10. FFR with ILUMIEN St. Jude. Medical
Editor's Notes
- #4: The ratio of distal coronary pressure to aortic pressure during maximal hyperemia is called the fractional flow reserve (FFR) and is a pressure-derived estimate of the percent of normal coronary blood flow that would be available to the myocardium. A normal value is 1, while values <0.80 are associated with provocable ischemia.
- #5: Fractional flow reserve is defined as the pressure behind (distal to) a stenosis relative to the pressure before the stenosis. The result is an absolute number; an FFR of 0.50 means that a given stenosis causes a 50% drop in blood pressure. In other words, FFR expresses the maximal flow down a vessel in the presence of a stenosis compared to the maximal flow in the hypothetical absence of the stenosis.
- #6: For the FFR a 0.014" sensor-tipped guidewires have been used safely and flow measurements distal to a stenosis. These can measure both pressures proximal, distal and flow velocity For the pressure-sensor guidewires, translesional pressure measured at maximum hyperemia is measured; hyperemia is induced by intravenous (140 mcg/kg/min) or intracoronary adenosine (30 to 60 mcg bolus).
- #7: The efficacy of FFR has been proven over many clinical trials such as FAME and FAME II.
- #8: Adenosie Papaverine NTP Regadenosin
- #9: Adenosine Papaverine NTP Regadenosin
- #12: Enter patient demographic. And click on start new FFR recording., Manufacture April 2014
- #13: Turn on machine by power button which located just right upper side of the keyboard.
- #14: For entering new patient just click on Add new patient, tab located mid upper right.
- #15: Entering patient demographic.
- #16: This is called WI Box
- #17: Connect direct one RJ
- #22: For Sensis Select Hemo P3 only in Lab 2 And Hemo P3 FFR in Lab 4
- #25: The new pressure wire “ Aeris “ features a specially developed hydrophilic coating that lower friction between guide wire and guide catheter as well as guide wire and device delivery system than other pressure wires.
- #28: Remove the pouch from the box. Remove pressure wire. Place the tray flat on table. Follow printed instruction on the tray to prepare pressure wire for use.
- #29: Fill Coil with Saline; take care not to expose pressure wire transmitter to fluids. Make sure to pull torque device forward along the wire; do not bend it loose.
- #30: Carefully tear open the flaps holding pressure wire transmitter to the tray. Lift pressure wire transmitter up and place it on the bed next to the tray without removing the wire from coil. Make sure pressure wire is fully inserted into pressure wire transmitter.