Fluke 1750 Calibration Manual

www.netzerotools.com
®

1750 Three Phase Power Quality Recorder
1750/B Three Phase Power Quality Recorder

1750
Power Recorder
Go To 1750 Products Page

Calibration Manual

November 2007 Rev. 1, 12/08
© 2007-2008 Fuke Corporation, All rights reserved. Product specifications are subject to change without notice.
All product names are trademarks of their respective companies.



LIMITED WARRANTY AND LIMITATION OF LIABILITY
Each Fluke product is warranted to be free from defects in material and workmanship under normal use and
service. The warranty period is one year and begins on the date of shipment. Parts, product repairs, and
services are warranted for 90 days. This warranty extends only to the original buyer or end-user customer of
a Fluke authorized reseller, and does not apply to fuses, disposable batteries, or to any product which, in
Fluke's opinion, has been misused, altered, neglected, contaminated, or damaged by accident or abnormal
conditions of operation or handling. Fluke warrants that software will operate substantially in accordance
with its functional specifications for 90 days and that it has been properly recorded on non-defective media.
Fluke does not warrant that software will be error free or operate without interruption.
Fluke authorized resellers shall extend this warranty on new and unused products to end-user customers
only but have no authority to extend a greater or different warranty on behalf of Fluke. Warranty support is
available only if product is purchased through a Fluke authorized sales outlet or Buyer has paid the
applicable international price. Fluke reserves the right to invoice Buyer for importation costs of
repair/replacement parts when product purchased in one country is submitted for repair in another country.
Fluke's warranty obligation is limited, at Fluke's option, to refund of the purchase price, free of charge repair,
or replacement of a defective product which is returned to a Fluke authorized service center within the
warranty period.
To obtain warranty service, contact your nearest Fluke authorized service center to obtain return
authorization information, then send the product to that service center, with a description of the difficulty,
postage and insurance prepaid (FOB Destination). Fluke assumes no risk for damage in transit. Following
warranty repair, the product will be returned to Buyer, transportation prepaid (FOB Destination). If Fluke
determines that failure was caused by neglect, misuse, contamination, alteration, accident, or abnormal
condition of operation or handling, including overvoltage failures caused by use outside the product’s
specified rating, or normal wear and tear of mechanical components, Fluke will provide an estimate of repair
costs and obtain authorization before commencing the work. Following repair, the product will be returned to
the Buyer transportation prepaid and the Buyer will be billed for the repair and return transportation charges
(FOB Shipping Point).
THIS WARRANTY IS BUYER'S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. FLUKE SHALL NOT BE LIABLE
FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OR LOSSES,
INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY.
Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or
limitation of incidental or consequential damages, the limitations and exclusions of this warranty may not
apply to every buyer. If any provision of this Warranty is held invalid or unenforceable by a court or other
decision-maker of competent jurisdiction, such holding will not affect the validity or enforceability of any other
provision.
Fluke Corporation Fluke Europe B.V.
P.O. Box 9090 P.O. Box 1186
Everett, WA 98206-9090 5602 BD Eindhoven
U.S.A. The Netherlands

11/99

To register your product online, visit http://register.fluke.com



Table of Contents

Title Page

Introduction........................................................................................................ 1
Contacting Fluke................................................................................................ 1
Safety Information ............................................................................................. 2
Symbols ............................................................................................................. 3
Specifications for the System: Recorder and Power Analyze Software ............ 3
General Specifications................................................................................... 3
Input Specifications ....................................................................................... 3
Synchronization and Sampling...................................................................... 4
Voltage and Current Measurements .............................................................. 4
Voltage and Current Measurement Accuracy ............................................... 4
Transient Voltage (Impulse).......................................................................... 4
Dip (Sag) and Swell Measurements .............................................................. 4
Power and PF Measurement .......................................................................... 5
External Interface Specifications................................................................... 5
Environmental and Safety Specifications...................................................... 6
Cleaning and Maintenance................................................................................. 6
Required Equipment .......................................................................................... 6
Verification Tests............................................................................................... 8
AC Voltage Accuracy Verification ............................................................... 8
Neutral Voltage Verification ......................................................................... 10
Rogowski Current Verification ..................................................................... 10
CT Current Verification ................................................................................ 11
Watt Verification ........................................................................................... 12
Impulse Verification ...................................................................................... 12
Calibration ......................................................................................................... 14
Required Equipment...................................................................................... 14
Calibration Adjustment ................................................................................. 14
Test Cables......................................................................................................... 16

i


1750
Calibration Manual

ii



List of Tables

Table Title Page

1. Symbols.................................................................................................................. 3
2. Required Equipment............................................................................................... 6
3. Required Cables ..................................................................................................... 7
4. AC Voltage Accuracy Verification ........................................................................ 9
5. Neutral (AC) Voltage Accuracy Check ................................................................. 10
6. Rogowski Current Accuracy Check ....................................................................... 11
7. CT Current Accuracy Check .................................................................................. 11
8. Impulse Verification Inputs.................................................................................... 14

iii


1750
Calibration Manual

iv



List of Figures

Figure Title Page

1. Power View Software Live View........................................................................... 9
2. Ground Calibration Cable ...................................................................................... 16
3. Rogowski Calibration Cable .................................................................................. 17
4. Rogowski Resistor Measurement Cable ................................................................ 18
5. Voltage Calibration Cable...................................................................................... 19
6. Current Calibration Cable ...................................................................................... 20

v


1750
Calibration Manual

vi



1750
Power Recorder

Introduction
XW Warning
To avoid electric shock or personal injury, do not perform the
calibration verification tests or calibration procedures
described in this manual unless you are qualified to do so.
The information provided in this manual is for the use of
qualified personnel only.
The 1750 Calibration Manual provides the following information:
• Precautions and safety information
• Specifications
• Basic maintenance
• Calibration procedures
• Verification procedures
• Replaceable parts and accessories
For complete operating instructions and calibration software, refer to the 1750 Users
Manual CD.

Contacting Fluke
To contact Fluke, call:
1-888-993-5853 in USA
1-800-363-5853 in Canada
+31-402-675-200 in Europe
+81-3-3434-0181 in Japan
+65-738-5655 in Singapore
+1-425-446-5500 from anywhere in the world
Or, visit Fluke’s Web site at www.fluke.com
To register your product, visit http://register.fluke.com

1


1750
Calibration Manual

To contact Technical Support:
fpqsupport@fluke.com
or 888-257-9897 (US only)

Safety Information
The 1750 Power Recorder (hereafter referred to as the Recorder) complies with
EN 61010-1 600 V CAT IV, 1000 V CAT III overvoltage rating. See Specifications for a
full agency compliance list.

XWWarning
To avoid electrical shock, personal injury, or fire:
• Review the entire manual before using the Recorder and its
accessories and observe all warnings and cautions.
• Do not perform the calibration verification tests or
calibration procedures described in this manual unless you
are qualified to do so.
• Avoid working alone.
• Do not operate the Recorder around explosive gas or
vapor.
• Use only insulated current probes, test leads, and adapters
as supplied with the Recorder, or indicated as suitable for
the Recorder.
• Before use, inspect the Recorder, voltage probes, current
probes, leads, and accessories for mechanical damage,
and replace when damaged. Look for cracks or missing
plastic. Pay special attention to the insulation surrounding
the connectors.
• Remove all probes, test leads, and accessories that are not
in use.
• Make sure the Recorder is properly connected through the
power cord to protective earth ground.
• Do not apply input voltages above the rating of the
Recorder as shown on the input panel.
• Do not apply voltages in excess of the marked ratings of
the voltage probes and current probes.
• Use caution if exposed metal BNC or banana plug
connectors are used for calibration. Avoid applying voltage
to the shell of the BNC during calibration.
• Do not insert metal objects into connectors.
• Never open the Recorder’s enclosure, dangerous voltages
are present. There are no user-replaceable parts in the
Recorder. Refer servicing of internal parts to qualified
service personnel.
• Use the Recorder only as specified in this manual, or the
protection provided by the Recorder may be impaired.

2


Power Recorder
Symbols

Symbols
Symbols used in this manual and on the Recorder are listed in Table 1.

Table 1. Symbols

Hazardous voltage. Risk of electrical Risk of danger. Important information. See
X shock.
W manual.

Conforms to requirements of European Do not dispose of this product as unsorted
P Union and European Free Trade ~ municipal waste. Go to Fluke’s web site for
Association (EFTA). recycling information.

Canadian Standards Association.
) [ Note: Canadian and US. ]
. Protective conductor terminal.

CAT III equipment is designed to protect
against transients in equipment in fixed- CAT IV equipment is designed to protect
equipment installations, such as against transients from the primary supply
CAT III CAT IV
distribution panels, feeders and short level, such as an electricity meter or an
branch circuits, and lighting systems in overhead or underground utility service.
large buildings.

Specifications for the System: Recorder and Power Analyze
Software
General Specifications
Power Quality Measurement Standards
Conformance..................................................... IEC 61999-1-4 Class 1, IEC 61000-4-30 Class A or B depending on
measurement function, IEEE519, IEEE1159, IEEE1459
Clock/Calendar.................................................. Leap years, 24-hour clock
Real-time Clock Accuracy................................ Not more than ± 1 s/day
Internal Memory Capacity for Data ................. At least 1 GB
Maximum Recording Period ............................ At least 31 days
Measurement Time Control ............................. Automatic
Maximum Number of Events ........................... Limited only by the size of the internal memory.
Power Requirements ........................................ 100 to 240 V rms ± 10 %, 47-63 Hz, 40 W
Operating Time During Interruptions
(internal UPS operation) ..................................... 5 minutes per interruption, 60 minutes total operating time without
recharging
Dimensions ....................................................... 215 x 310 x 35 mm (8.5 x 12.2 x 3.5 inch)
Mass (Weight) ................................................... 6.3 kg (14 lbs)

Input Specifications
Measurement Types ......................................... One Phase Plus Neutral, One Phase IT No Neutral, One Phase Split
Phase, Three Phase Wye, Three Phase Delta, Three Phase IT, Three
Phase High Leg, Three Phase Open Leg, 2 Element Delta, 2 ½
Element Wye
Input Channels .................................................. Voltage: 5 channels, AC/DC
Current: 5 channels
Voltage Channels.............................................. Input resistance: 2 MΩ
Input capacitance: <20 pF
Current Channels.............................................. 1 MΩ. Self-identifying probes
Types available: current clamps, Flexi-CTs
Measuring Method ............................................ Simultaneous digital sampling of voltage and current. Digital PLL
synchronized sampling, internal frequency reference used during
voltage drops.

3


1750
Calibration Manual

Synchronization and Sampling
PLL-Synchronization Source........................... The PLL synchronizes to the A-N voltage for wye power types, and to
the A-B voltage for delta power types. All listed power types can be
characterized as either wye or delta.
PLL Lock Range................................................ 42.5 to 69 Hz
Sampling Frequency ........................................ Voltage and current: 256 samples/cycle
Inter-harmonics per IEC61000-4-7: 2560 samples / 10 cycles (50 Hz),
3072 samples/12 cycles (60 Hz)
Transient Voltage: 5 MHz
A/D Resolution .................................................. Voltage and current: 24 bits
Transient voltage: 14 bits

Voltage and Current Measurements
Voltage Measurement Range........................... AC voltage: 1000 V rms ± 10 % Overrange
DC voltage: ± 1000 V + 10 % Overrange
Voltage Crest Factor......................................... 3 or less
Voltage Input Impedance ................................. 2 MΩ
Current Measurement Range........................... Depends on current probe used
Current Crest Factor......................................... 4 or less
Current Input Characteristics .......................... 2 V rms = full scale, 1 MΩ Input Impedance for ferro CTs, low
impedance for Flexi-CTs

Voltage and Current Measurement Accuracy
RMS Voltage
Measurement Type ............................................. True rms calculated continuously: every cycle, every 1/2 cycle, and
every 10 or 12 cycles at 50 or 60 Hz respectively, as required by IEC
61000-4-30.
Measurement Uncertainty................................... AC: ± 0.2 % reading ± 0.1 % full scale above 50 V rms
DC: ± 0.5 % reading ± 0.2 % full scale above 50 V dc
If the ac component of a dc signal is below 40 V rms, the dc
uncertainty specification may have an offset.
RMS Current
Measurement Type ............................................. True rms calculated continuously: every cycle, every 1/2 cycle, and
every 10 or 12 cycles at 50 or 60 Hz respectively, as required by
standards
Measurement Uncertainty................................... ± (0.1 % full scale + 0.5 % reading + current sensor accuracy, valid for
5 % to 100 % of current sensor range

Current Accuracy ................................................ Ferromagnetic Clamps
± (0.1 % full scale + 0.2 % reading + current sensor accuracy), valid for
Flexible Current Probes
± (0.1 % full scale + 0.5 % reading + current sensor accuracy), valid for

Transient Voltage (Impulse)
Measurement Type ............................................. Waveshape sampling, not peak detect
Full Scale ............................................................ 8000 V pk
Sample Resolution.............................................. 200 nS
Measurement Uncertainty................................... ± 5 % reading ± 20 V (test parameters: 1000 V dc, 1000 V rms,
100 kHz)

Dip (Sag) and Swell Measurements
Voltage Swell (rms swell)
Measurement Type ............................................. True rms (one cycle calculation by overlapping each half cycle)
(voltage between lines is measured for 3P3W lines and phase voltage
is measured for 3P4W lines)
Displayed Data ................................................... Amplitude and duration of swell

4


Power Recorder
Specifications for the System: Recorder and Power Analyze Software

Measurement Accuracy ...................................... Same as rms voltage
Voltage Dip (RMS sag)
Measurement Type ............................................. True rms (one cycle calculation by overlapping each half cycle)
(voltage between lines is measured for 3P3W lines and phase voltage
is measured for 3P4W lines)
Displayed Data ................................................... Amplitude and duration of dip or interruption
Measurement Accuracy ...................................... Same as rms voltage
Voltage Dropout (Interruption)
Measurement Type ............................................. Same as Voltage Dip

Power and PF Measurement
Power
Measurement Method ......................................... Calculated per IEEE1459 for best performance when distortions exist
Measurement Type ............................................. True rms calculated continuously: every cycle, and every 10 or 12
cycles at 50 or 60 Hz respectively, as required by standards
Measurement Accuracy ...................................... ± 0.2 % reading ± 0.1 % full scale + current sensor accuracy
Frequency
Measurement Range .......................................... 42.5 to 69 Hz
Measurement Source ......................................... Same as PLL synchronization source
Measurement Accuracy ...................................... ± 10 mHz (10 to 110 % of range, with sine wave)
Reactive Power
Accuracy ............................................................. ± 0.2 % reading ± 0.1 % full scale + current sensor accuracy
Power Factor
Measurement Range .......................................... -1.000 (leading) to 0.000 to +1.000 (lagging)
Measurement Accuracy ...................................... ± 1 digit from the calculation of each measured value (± 3 digits for
total)
Displacement Power Factor
Measurement Method ......................................... Calculated from the phase difference between voltage fundamental
and current fundamental
Measurement Range .......................................... - 1.000 (leading) to 0.000 to + 1.000 (lagging)
Measurement Accuracy ...................................... ± 0.5 % reading ± 2 % full scale ± 1 digit
Voltage Unbalance and Phase Sequence
Measurement Method ......................................... Positive sequence voltage divided by negative sequence voltage, per
IEC 61000-4-30
Harmonic Voltage and Current
Analysis Window................................................. rectangular
Analysis Order .................................................... 1st to 50th order
Measurement Accuracy ...................................... Voltage / Current: 1st to 20th orders: ± 0.5 % reading ± 0.2 % full scale
21st to 50th orders: ± 1 % reading ± 0.3 % full scale
(current sensor accuracy must be included for current and power)
Measurement Method ......................................... IEC 61000-4-7
Inter-harmonic Voltage and Current (Intermediate Harmonics)
Analysis Window................................................. rectangular
Analysis Orders .................................................. 0.5 to 49.5th order
Measurement Method ......................................... IEC 61000-4-7

External Interface Specifications
LAN Interface
Connector ........................................................... RJ-45
Speed and Type ................................................. 10/100 Base-T, auto MDIX
Communications Protocol ................................... TCP/IP over Ethernet
Wireless Controller Interface
Connection.......................................................... wireless (2.4 GHz radio)
Speed ................................................................. up to 700 kbit/second
Communications Protocol ................................... Bluetooth SPP

5


1750
Calibration Manual

Environmental and Safety Specifications
Operating Environment ....................................... indoors or in covered area outdoors, up to 2000 m altitude
Storage Temperature and Humidity.................... -20 °C to 50 °C, 80 % rh max, non-condensing
Operating Temperature and Humidity ................ 0 °C to 40 °C, 80 % rh max, non-condensing
Maximum Rated Working Voltage
Voltage Terminals ............................................. 1100 V rms
Voltage Durability................................................ 5550 V rms ac for 1 minute, between voltage input terminals, voltage
input terminals and current probes, and voltage input terminals and
case (50/60 Hz, 1 mA sense current)
Enclosure Protection........................................... IP30 (per EN 60529)
Standards Conformance
EMC .................................................................... EN 61326-1:2000 Class A
EN 61000-3-2:1995+A1:1998+A2:1998
EN 61000-3-3:1995
nd
Safety.................................................................. EN 61010-1:2 Edition
Voltage input unit: Contamination Level 2
Measurement Category 1000 V CAT III, 600 V CAT IV (transient: 8 kV)

Cleaning and Maintenance
WCaution
To avoid damage to the Recorder, do not apply abrasives or
solvents to the housing.
The Recorder contains no user serviceable parts. Contact an authorized Fluke service
center for repair. See Contacting Fluke.
Periodically wipe the case with a damp cloth and mild detergent.

Required Equipment
For a list of required equipment for the verification tests and calibration adjustment, see
Tables 2 and 3.

Table 2. Required Equipment

Equipment Required Characteristics Recommended Model

AC Voltage Range: 0 - 1000 V ac
Accuracy: ± 0.03 %
Fluke 5520A Multi-Product
Calibrator Frequency Range: 50 - 10000 Hz
Calibrator or equivalent
DC Voltage Range: 0 - 1000 V dc
Accuracy: ± 0.03 %

Ohms Range: 100 KΩ Fluke 8846A Precision
Multimeter with 4-wire Ohms
Accuracy: ± 0.011 % Multimeter or equivalent

Personal Computer (PC) 1750 Cal Wizard and Fluke Power
(Windows XP) Analyze software installed

6


Power Recorder
Required Equipment

The cables listed in Table 3 are necessary for verification and calibration adjustment. To
assemble the cables, see cable assembly figures in the Test Cables section.

Table 3. Required Cables

Cable Required Characteristics Notes

Ethernet cable CAT 5 with RJ-45 connectors Supplied with the Recorder

Voltage calibration cable Double banana to safety banana
See Figure 5
with BNC-banana adapter and spade lug
Four jumper cables, safety-
banana type
Shielded cable with double banana
Current calibration cable to CT pins in Redel connector with See Figure 6
100 A CT ID resistor
Rogowski resistor
Safety banana to Redel See Figure 4
measurement cable
Shielded cable with double banana
Rogowski calibration cable to Rogowski pins in Redel connector See Figure 3
with 100 A Rogowski ID resistor
Ground calibration cable Lug to banana See Figure 2

Fluke recommends the use of Pomona brand cables and banana plugs when building these cables.

7


1750
Calibration Manual

Verification Tests
XWWarning
• Do not perform the calibration procedures or calibration
verification tests described in this manual unless you are
qualified to do so.
• Repairs or servicing should be performed only by qualified
personnel.
The following tests are used to verify the functions of the Recorder. If the Recorder fails
any of the verification tests, calibration or repair may be needed. For service, see
Contacting Fluke.

Note
Power Analyze can be set to display the channels as L1, L2, and L3 instead
of A, B, and C. The channels on the Recorder could also be labeled A, B,
and C, or L1, L2, and L3, depending on which decal was applied to the
Recorder front panel. For this manual A, B, and C are used.

AC Voltage Accuracy Verification
1. Connect an Ethernet cable to the Recorder.
2. Apply power to the Recorder. During power up, indicators near all jacks should flash.
3. Launch Power Analyze software on a personal computer (PC).
4. Select the Recorder to be tested in the drop down box next to the Scope button.
5. Select 1750 Live, then Scope.
6. Check all the voltage display check boxes to the right of the scope display. Make sure
the correct items are checked.

8


Power Recorder
Verification Tests

power analyze live view screen.bmp
Figure 1. Power View Software Live View

7. Connect the calibrator NORMAL HI to inputs A, B, C, and J of the Recorder.
8. Connect the NORMAL LO to input N and the protective conductor terminal . of
the Recorder.
9. Apply the voltages from Table 4 and list the Recorder readings for channels AN, BN,
CN, and NG in the appropriate areas. Sine waves will be displayed for AN, BN and
CN, all at the same amplitude and phase shift. NG will be inverted.

Note
If the voltage goes over scale, right click on the voltage scale on the left
margin of the graphical display, then click on the Zoom to Fit box to
resize.

Table 4. AC Voltage Accuracy Verification

Applied AN Reading BN Reading CN Reading NG Reading Limits

60 Vrms @ Local Hz ± 1.12 V



10. Verify that A, B, C, and J LEDs are on. N should be off.
11. Set the calibrator to STBY.
12. Verify that A, B, C, and J LEDs are off.

9


1750
Calibration Manual

Neutral Voltage Verification
1. Connect NORMAL LO to A, B, C, J, and ..
2. Connect the calibrator NORMAL HI to N on the Recorder.
3. Apply the voltages from Table 5, listing the Recorder readings for the appropriate
model.

Table 5. Neutral (AC) Voltage Accuracy Check

Applied NG Reading Limits

60 V @ Local Hz ± 1.12 V

100 V @ Local Hz ± 1.20 V

4. Verify that the N LED is on.
5. Set the calibrator to STBY, verify that the LED for N turns off.
6. Disconnect the test leads from the Recorder.

Rogowski Current Verification
1. Verify the resistor in the Rogowski calibration cable is within 0.1 % of 100 kΩ.
2. Connect the calibrator NORMAL HI to Voltage A, B, and C on the Recorder.
3. Connect the calibrator NORMAL LO to N and Voltage J on the Recorder.
4. Connect the calibrator AUX HI and LO to current input A using the Rogowski
calibration cable. See Figure 3.
5. Set the calibrator output to 120.0 V @ 55 Hz on the NORMAL output and the values
from Table 6 the AUX output.
6. Press the WAVE MENUS softkey and ensure the phase angle is -90 °.
7. Press the HARMONIC MENU softkey; ensure the HARMONIC selection is set to
1 and the FUNDMTL selection is set to aux.
8. Press OPR.
9. Set the calibrator to voltages from Table 6 and list the Recorder readings for channel
A.
10. Move cable to next channel and repeat step 9 for channels B, C, N, and J.

10


Power Recorder
Verification Tests

Table 6. Rogowski Current Accuracy Check

Applied Expected Expected
A Reading B Reading C Reading N Reading G Reading Limits
Voltage Current Reading

0.649 V 6.49 μA 20 A ± 0.20 A

1.6225 V 6.225 μA 50 A ± 0.35 A

3.245 V 32.45 μA 100 A ± 0.60 A

CT Current Verification
1. Connect the calibrator NORMAL HI to Voltage A, B, and C on the Recorder.
2. Connect the calibrator NORMAL LO to Voltage N and J on the Recorder.
3. Connect the calibrator AUX HI and LO to current input A using the current test
cable. See Figure 6. The current test calibration cable connects the voltage to all
current sense inputs and indicates that a 100 A current transformer is attached.
4. Set the calibrator output to 120.0 V @ 50 or 60 Hz on the NORMAL output and the
values from Table 7 on the AUX output.
5. Press the WAVE MENUS softkey and ensure the phase angle is 0.0 °.
6. Press the HARMONIC MENU softkey; ensure the HARMONIC selection is set to
1 and the FUNDMTL selection is set to aux.
7. Press OPR.
8. Set the calibrator to voltages from Table 7 and list the Recorder readings for that
channel.

Table 7. CT Current Accuracy Check

Expected
Applied Voltage A Reading B Reading C Reading N Reading G Reading Limits
Reading

0.4 V 20 A ± 0.20 A

1.0 V 50 A ± 0.35 A

2.0 V 100 A ± 0.60 A

9. Verify that the current LED is on.
10. Move cable to next channel and repeat steps 8 and 9 for channels B, C, N, and J.
11. Set the calibrator to STBY. Verify that the current LEDs turn off.

11


1750
Calibration Manual

Watt Verification
1. Use the same connections as the CT current verification and apply 440 V and local
line frequency out of the NORMAL output and 1.9 V on the AUX output.
2. Click on the power button in Power Analyze. The A, B and C should be 41.8 kW ±
0.3 kW.
3. On the calibrator press the blue button for Phase and Ref Menu.
4. Press the blue button for AUX Phase NRM.
5. Enter 90 with the numerical keypad and press Enter. The power should be 0 ±
0.1 kW.

Impulse Verification
Initialize the UUT
XWWarning
The impulse verification steps instruct the user to apply
working voltages in excess of 700 V, so extreme caution must
be applied. To avoid electrical shock or personal injury, DO
NOT use connectors having exposed metal.
1. Power down the UUT until Power LED turns off, approximately five minutes.
2. Power up the UUT and wait for start up, and connect with Power Analyze.
3. Select Tools>Erase 1750 Memory to empty the UUT data.

Normalize Thresholds
4. Connect the calibrator NORMAL LO to the UUT . terminal.
5. Connect the voltage test cable to the calibrator NORMAL HI jack, leaving the
safety-connector end free.
6. Set the calibrator to 750 V 10 kHz.
7. Press OPR on the calibrator.
8. Connect the voltage test cable to UUT voltage input J for approximately 15 seconds,
and then disconnect.

Apply Stepped Verification Voltages to Voltage Inputs A, B, C, N, and J
10. Connect the voltage test cable to UUT voltage input A for approximately 15 seconds,
12. Connect the voltage test cable to UUT voltage input B for approximately 15 seconds,
14. Connect the voltage test cable to UUT voltage input C for approximately 15 seconds,
16. Connect the voltage test cable to UUT voltage input N for approximately 15 seconds,
then disconnect.

12


Power Recorder
Verification Tests

18. Connect the voltage test cable to UUT voltage input J for approximately 15 seconds,
then disconnect. Note, this signal is designated G in Power Analyze.
19. Press STBY on the calibrator.
20. Set the calibrator to 0 V 0 Hz.

To Use Power Analyze to Verify the Amplitude Accuracy of Recorded Impulse Events
21. Wait two minutes for the UUT to compile event information.
22. Click on 1750 Download, and then Save.
23. Click on View Recorded, and then Events.
24. On the right side, verify that all four Volts selections are checked and all five Amps
selections are unchecked in Phase Selection, and Phase to Neutral is selected in
Voltage Reference.
25. Click on Event Detector.
26. Select all channels the same and set both AN and the NG thresholds to 50 %.
27. Click Done.
28. Click on View > Table View > Top Table View. This changes the Event Summary
data at the top of the screen from graph-view to table-view.
29. Click on View > Screen View > Top Full Screen. This provides a full screen view
of the Event Summary table.
30. The following steps concern the two right-hand columns in the Event Summary table,
the Absolute and Triggered Phase columns.
31. Starting from Event 1, scroll down the table through the NG Triggered Phase data
until the AN Triggered Phase data is reached. This group of NG Triggered Phase data
is from the Normalize Thresholds section of this check. It is not used for verification.
32. Scroll down through the AN Triggered Phase data until the BN Triggered Phase data
is reached. Record the sixth-to-last AN Triggered Phase Absolute value in Table 8.
33. Scroll down through the BN Triggered Phase data until CN is reached.
34. Record the sixth-to-last BN Triggered Phase Absolute value in Table 8.
35. Scroll down through the CN Triggered Phase data until N-triggered data is reached.
Because voltage events on N cause triggers on AN, BN, CN, and NG, (resulting in
any one of these labels) this can be most easily distinguished by the change in the
Absolute values from the CN Triggered Phase data. Record the sixth-to-last CN
Triggered Phase Absolute value in Table 8.
36. Scroll down through the N-triggered data until G-triggered data is reached. As with
the previous step this can be most easily distinguished by the change in the Absolute
values from the Triggered Phase data.
37. Record the sixth-to-last N-triggered Phase Absolute value in Table 8.
38. Scroll to the bottom of the Event Table until the end of the G-triggered data is
reached. These will all show up as NG for Triggered Phase.
39. Record the sixth-to-last N-triggered Phase Absolute value in Table 8.

13


1750
Calibration Manual

Table 8. Impulse Verification Inputs

Applie
Expected
d Measured Magnitude Limits
Reading Channel
Voltage |Vpk| [Vpk]
[Vpk]
[Vrms]

800 1131 AN (A) ± 77

850 1202 BN (B) ± 80

900 1273 CN (C) ± 84

950 1344 NG (N) ± 87

1000 1414 NG (G) ± 91

Calibration
Required Equipment
The required equipment and cables for calibrating the Recorder are listed in Tables 2 and
3.

XWWarning
• Do not perform the calibration procedures or calibration
verification tests described in this manual unless you are
qualified to do so.
• Repairs or servicing should be performed only by qualified
personnel.

Calibration Adjustment
The Recorder features closed-case calibration adjustment using known reference sources.
During calibration, the Recorder measures the applied reference source, calculates
correction factors, and stores the correction factors in nonvolatile memory.
Perform calibration adjustment if the Recorder fails any performance test in the
verification procedure.

Note
Calibration should be performed under ambient temperature conditions
between 20 °C and 30 °C.
Calibration consists of four parts: I-Wave, I-Rogowski, V-Wave, and V-Impulse. Each
part calibrates one measurement system in the Recorder. For each part, the calibration
values are checked to be sure the Recorder is working correctly and calibration results are
valid. All of the calibration steps for each of the four measurement systems must be
completed before the calibration values can be written to the Recorder’s nonvolatile
memory.
I-Wave, I-Rogowski, and V-Wave channels are calibrated using 55 Hz sine wave signals
to minimize 50 Hz or 60 Hz power line interference with the calibration measurements.
V-Impulse channels are calibrated using dc voltages, averaging calibration measurements
to suppress power line interference.

14


Power Recorder
Calibration

Calibration is controlled by 1750 Cal Wizard Software (Cal Wizard), which
communicates with the Recorder over Ethernet. Cal Wizard steps through the calibration
procedure, with instructions for making cable connections, setting the correct sources,
and finalizing the calibration.
The following steps detail the calibration adjustment procedure:
1. Connect the Recorder and the PC to the network with an Ethernet cable. This can
either be by direct connection or via a hub on an Ethernet network.
2. Connect ac power to the Recorder. Make sure the Recorder, calibrator, and PC
running Cal Wizard software are all properly connected to safety ground.
3. Allow the calibrator and Recorder to warm up (30 minutes for the Recorder). If
necessary, run Ohms-Cal or Zero-Cal on the calibrator.
4. Reset the calibrator. Confirm the following calibrator state: 0 V, Standby (OPR LED
off), EARTH Off (LED off), and EXGRD Off (LED off).
5. Start Cal Wizard.
6. With Cal Wizard, select the Recorder to be calibrated, and then click Connect.

Note
If the Recorder is password protected, the correct password must be
supplied to continue.
7. Click Next.
8. Follow the on-screen instructions to perform each of the four calibration types. If any
of these procedures report a failure, the Recorder must be returned for inspection and
service. See Contacting Fluke.
9. If all calibrations are successful, click Apply to store the correction values in the
Recorder memory. This will take up to a minute to complete.
10. Click Finish. The Recorder will shut down and restart using the new calibration
values. This may take several minutes.
This concludes Recorder calibration.

15


1750
Calibration Manual

Test Cables
The following figures detail the assembly of cables used for calibrating the Recorder.

fdo02.eps
Figure 2. Ground Calibration Cable

16


Power Recorder
Test Cables

fdo01.eps
Figure 3. Rogowski Calibration Cable

17


1750
Calibration Manual

fdo05.eps
Figure 4. Rogowski Resistor Measurement Cable

18


Power Recorder
Test Cables

fdo03.eps
Figure 5. Voltage Calibration Cable

19


1750
Calibration Manual

fdo04.eps
Figure 6. Current Calibration Cable

20


Fluke 1750 Calibration Manual

More Related Content

What's hot (10)

Similar to Fluke 1750 Calibration Manual (20)

More from videoborescope (14)

Recently uploaded (20)

Fluke 1750 Calibration Manual