FPGA BASED HEARTBEATS MONITOR WITH FINGERTIP OPTICAL SENSOR

International Journal of Computer Science, Engineering and Information Technology (IJCSEIT), Vol. 4, No.5, October 2014
DOI : 10.5121/ijcseit.2014.4501 1
FPGA BASED HEARTBEATS MONITOR WITH
FINGERTIP OPTICAL SENSOR
Wahyu Kusuma R.1
, Ridha I.2
, Yasman Rianto3
, Swelandiah E.P4
1,3
Departement of Electrcal Engineering, Gunadarma University, Jakarta, Indonesia
2,4
Departement of Computer Science, Gunadarma University, , Jakarta, Indonesia
ABSTRACT
The heart is an organ of human body which has a vital function, small abnormalities can have a big impact
on the performance of the body. Heart disease is the number one cause of death in the world. Examination
of the heart can be detected from blood flow in the fingertips, in order to obtain information about the
number and rhythm of the heartbeat. This research aims to design and implement the FPGA board to
monitor the heart rate with optical sensors.The results of this study are expected to facilitate the patient's
medical team or independently in detecting heart health. The series is composed of blocks of sensors,
signal conditioning block, the block pulse counter, block timer 10 seconds and blocks the viewer. Based on
the test results of the 10 respondents with a variety of age and gender, has built a tool that the percentage
error of 3.94%.
KEYWORDS
Heartbeat monitor, Xilinx ISE Webpack, FPGA, optical sensor
1. INTRODUCTION
The heart is an organ of human body which has a vital function, small abnormalities can have a
big impact on the performance of the heart kita.Penyakit body is the number one cause of death
in the world. Based on data from the World Health Organization (WHO), cardiovascular disease
has reached 29% in the percentage of deaths in the world and 17 million people die every year
due to heart and blood vessel disease throughout the world [3].
The development of medical instrumentation systems is growing rapidly along with the need for
medical personnel to diagnose a patient and a medical examination. One medical instrumentation
used for the examination of the heart is Electrocardiograph (ECG). ECG is a medical instrument
that is commonly used by the medical team to detect heart rate and rhythm [6]. EKG can not be
used independently by patients to detect a patient's pulse. In addition to the expensive costs for
the procurement of ECG, ECG devices also require special skills to operate.
Along with the requirement in the design and manufacture of medical devices, digital electronics
design technology is developing very rapidly, both in terms of hardware and software. Xilinx is
one manufacturer that produces equipment or tools for modeling the design of digital systems.
One product is in the form of a kit module board FPGA (Field Programmable Gate Array).
FPGA is a programmable device that is composed of large modules independent logic that can be
configured by the user who is connecting through the canals of programmable routing [4].

2
Field Programmable Gate Array (FPGA) has advantages of which can be configured by the End
User, does not require the fabrication process, and the available solutions that support
customized VLSI chip, so the logic circuit capable of implementing, instant manufacturring,
very-low cost prototype. While FPGA product is also supported by the availability of the Xilinx
ISE WebPack permograman language that is used as a GUI for the digital system design
problems is desired.
Based on the above issues, this study will design a device that can detect heart rate by detecting
the frequency of blood flow to the fingers automatically processed electronically using the
module FPGA (Field Programable Gate Array). This research is expected to generate a heartbeat
detector chip implementation can provide facilities for the medical and can be used
independently by the user (patient) without the help of a doctor or paramedic.
2. ARCHITECTURE AND ITS IMPLEMENTATION
This research conducted several phases of hardware design, software design pelangkat, testing
tools, and analysis to draw conclusions.
2.1 Hardware Design
The design of this tool consists of several circuit blocks are arranged into a single system
heartbeats monitoring based on optical sensors, as shown in Figure 1.
Figure 1. Block Diagram Tool Heartbeats Detection Based on Optical Sensors
2.1.1. Optical Sensor Unit
The sensor consists of a transmitter that emits infrared light (IR) and IR photo detector
(photodiode) to act as a receiver. Construction sensor block shown in Figure 2. The use of optical
sensors for process monitoring heart rate with fingertip illustrated as a figure 3.

3
Figure 2. Optical sensor circuit Figure 3. Ilustration fingertip to optical sensor
2.1.2. Conditional Signal Unit
The output signal of the sensor is very small and still a lot of noise. This signal before entering
the pulse counter block should be done in conditioning, so signal that result this block is ready to
be read or processed by the block counter. The signal conditioner block consists of a series of low
pass filter and amplifier structure is shown as figure 4.
Figure 4. Diagram Block of Conditional Signal Unit
Figure 5. Optical Sensor and Conditional Signal Circuits
2.1.3. Heart Counter Unit
This block is used to calculate the output signal generated by the signal conditioning block.
Signals that represent a high rate, while the low signal represents the absence of heartbeat. So this
block will calculate the amount of high signal.
The basic principle of this block as a series of counters. This block has three inputs namely are
Clk signal, the signal In is connected to the output signal conditioning block and Enable signal
(En) which is connected to the output signal at the timer block. The output of the pulse counter
block form as 6-bit binary sequence (D5, D4, D3, D2, D1, D0). In this research, the pulse

4
counter block is designed with programming languages Xlinx WebPack ISE. The design of the
pulse counter block is shown as figure 6.
Figurer 6. Design of Heart Counter Unit
2.1.4. Timer 10s Unit
This block is designed for pulse counting process is done by calculating the input signal to the
timer block rate for 10 seconds. The basic principle of the timer unit is a clock signal frequency
divider circuit. The clock signal is taken from the internal oscillator signal frequency of 50 MHz
on the FPGA module. In order to get a signal with a period of 20 seconds, then beat signal as a
function of the timer must have a frequency of 50 mHz, by taking half the period of the high
level. The output signal timer 10s unit to be input to the Enable signal (En) at the pulse counter
block. The timer 10s unit is shown in Figure 7.
Figure 7. Diagram Block of Timer 10s
2.1.5. Display Unit
The Display unit that is used is the 6 Led (D5, D4, D3, D2, D1, D0) which represents the value of
the output of the pulse counter block. In addition, the results of the calculation rate is also
displayed with an LCD unit. This block already exists in the module of Spartan 3E FPGA Starter
Kit [4], as shown in the figure 8.
Figure 8. Display of LED and LCD at FPGA Spartan 3E Starter Kit [4]
2.2. Designing of Programming Xilinx ISE Webpack
In this research, design of Xilinx ISE Webpack program done on the pulse counter block and
block the timer 10s. The programming result, then applied to the module Field Programable Gate

5
Array (FPGA), through the implementation process. Output of this system is the number of
heartbeat information in 1 minute, which known as beat permenit (bpm). Using of this system,
in the process of beating the count is done for 10 seconds as the sample to calculate the 1 minute,
so to show the heartbeat detection for 1 minute, required multiple of 6 constant number.
Flowchart program of heartbeat monitoring device shown in figure 9.
Results from the VHDL programming of heartbeat monitorr has been simulated correctly, then
the program is implemented on Spartan 3E FPGA board.
Figure 9. Flowchart of Heart Rate Monitoring VHDL Programming

6
2.3. RTL Viewer
Figure 10. RTL Viewer Heartrate Monitor
After the process of synthesis and design implementation, next the process is VIEW RTL
Schematic, as shown in the figure 10. This figure describes the gates configuration that represent
the pulse counter and the timer 10s devices.
3. EXPERIMENTAL RESULT
3.1 Conditional Signal Output Testing
Based on Figure 11, can be explained that the heart rate signal measurement results using the
oscilloscope at the output of the signal conditioner has a value of amplitude of 8.4 V, with a value
of 800 ms period or frequency of 1.25 Hz.
Figure 11. Display of output the signal conditioning block on the oscilloscope output
.
3.2. Simulation Results Heartbeat Counters Block
Testing in this section is to observe the results display on the programming VHDL simulation
with Xilinx Isim, as shown as Figure 12.

7
Figure 12. Display of simulation result
Figure 12 shows an example of simulation result Heartbeat Counters Block with a insensor input
signal with a period of 450ms (1.33Hz). At the output outcounter generate data 010111b, which
represents the beating of the time there are 23 counters for 10 seconds. So that the calculation
results heartbeat (heart rate) for 23 x 6 = 138 bpm (beats perminute).
3.3 Testing Results of The Heartbeats Monitor Device
Testing is done by calculating the heart rate to some respondents. Based on the output pulse
counter block built instrument (ha) compared with the measurement results using a fingertip pulse
sensor oxymeter (ho) in units of bpm. Difference in outcome differences between the two
devices, then calculated the percentage error (% Er) with the equation:
………………..……………………..(1)
Table 1: Testing results of the heartbeats monitor device
Responden
LED Condition
FPGA
Heart Rate
(bpm)
LCD
Heart Rate
(bpm)
Oxymeter
Error (%)
D5 D4 D3 D2 D1 DL0
1 0 0 1 1 0 1 78 76 2,6
2 0 0 1 0 1 1 66 70 5,7
3 0 0 1 1 1 0 84 82 2,4
4 0 0 1 1 0 1 78 77 1,3
5 0 0 1 1 1 0 84 81 3,7
6 0 0 1 1 0 0 72 75 4
7 0 0 1 1 1 1 90 84 7,1
8 0 0 1 1 0 1 78 82 7,3
9 0 1 0 0 0 0 96 94 2,1
10 0 0 1 1 1 1 90 93 3,2
Table 1 shows the trial against six respondents. At trial respondent 1, the output of the gain block
rate pengitung 001101b value as indicated by the LED flash is worth 1, and if the flame is not
worth 001101b value 0 is equivalent to 13d. Furthermore, to get the heart rate measurement with
units of beats per minute (bpm) needs to be multiplied by a constant 6 Thus, respondent 1 has a
value of 13 x 6 = 78 bpm. The same was done for the other respondents. Measurement accuracy

8
in terms of percentage error is calculated using equation (1). Based on the test results in Table 1,
it has been tested tool designed to measure the number of heartbeats to 10 respondents, has an
error (Error) an average of 3.94%.
4. CONCLUSION
This research has successfully designed a heartbeat monitor circuit using the Xilinx ISE program
WebPack 13.1. The series is composed of sensors block, signal conditioning block, pulse counter
block, timer 10s unit and the display unit. Based on the test results of the 15 respondents, a tool
designed to have a percentage error of 3.28%.
5. SUGESTION
a. In the testing process, the accuracy of the optical sensor is strongly influenced on laying /
finger placement ujuag. So to overcome this required the manufacture of containers or the
media, so the detection of blood flow in the fingertips can be precision quickly.
b. In the signal conditioning block in this research, design and manufacturing are still using
electronic components. In further studies need to be developed to block the signal conditioner
made with vhdl programming, thus forming sauté specific integrated circuits or ASICs known
(Application-Specific Integrated Circuits)
Figure 13. FPGA based heartbeats monitor circuit
REFERENCES
[1] Dogan., I., Kadri., B, 2012, Hear Rate Measurement from the Finger using a low cost
Microcontroller, http://www.emo.org.tr/ekler/ a568a2aa8c19a31_ek. pdf,
[2] Machriz, E., Sony S., Achmad R., 2008, Perancangan Perangkat Monitoring Denyut Jantung (Heart-
Beat Monitoring) dengan Visualisasi LCD Grafik Berbasis ATMEL AT89C51, proseding
Konferensi Nasional Sistem dan Informatika 2008; Bali, November 15, 2008.
[3] Hadiyani N., , 2012, Penyakit Jantung Koroner, http://www.dokterku-
online.com/index.php/article/54-penyakit-jantung-koroner, 14 Februari 2014
[4] Pong P. C., 2008, FPGA Prototyping by VHDL Examples: Xilinx Spartan-3 Version, Publisher:
Wiley-Interscience
[5] Sharief F. B., Liena E., Abdel K., Samah M. E., 2011, Microcontroller Based Heart Rate Monitor
using Fingertip Sensors, UofKEJ Vol. 1 Issue 2 pp. 47-51,October 2011
[6] Webster, EDS, 1981, Design of Microcomputer-Base Medical Instrumentation, Prentice Hall
International, New Jersey
Optical Sensor
Conditional Signal
Circuit
Xilinx Spartan 3E
FPGA

9
Authors
Wahyu Kusuma R received the Dr. in information technology from Gunadarma University, in
2008. Currently, he is a Electrical and Computer Laboratory staff at Gunadarma University.
His research interests include Voice Recognition Systems, Music Information Retrieval and
Embedded Systems with FPGA
Ridha Iskandar received the Dr. in information technology from Gunadarma University, in
2009. Currently, he is a computer Science laboratory staff at Gunadarma University. His
research interests include Biomedical Signal Processing and Embedded Systems with FPGA.
Yasman Rianto received as Student the Doctoral in information technology from
Gunadarma University, in 2013. Currently, he is a Physic laboratory staff at Gunadarma
University. His research interests include Sensoring and Microcontroller Application
Swelandiah E. Pratiwi graduated form Master of Electrical Enginering Gunadarma
University, in 2006. Currently, he is a Information Technology laboratory staff at
Gunadarma University. His research interests include Embedded System and Microcontroller
Application.

FPGA BASED HEARTBEATS MONITOR WITH FINGERTIP OPTICAL SENSOR

More Related Content

What's hot (20)

Similar to FPGA BASED HEARTBEATS MONITOR WITH FINGERTIP OPTICAL SENSOR (20)

Recently uploaded (20)

FPGA BASED HEARTBEATS MONITOR WITH FINGERTIP OPTICAL SENSOR