Honeywell 5870api-install-guide
0 likes233 views
The document provides installation and setup instructions for a wireless indoor asset protection device. It describes selecting an installation location away from vibration sources, choosing an operating mode depending on the asset's movement, and programming the device for use with a security system control panel. Instructions are given for mounting the sensor directly on the protected asset and testing the system once installed.
Honeywell 5870api-install-guide
- 1. K14379V2 1/10 Rev. A 5 870API Wireless Indoor Asset Protection Device INSTALLATION AND SETUP GUIDE QUICK INSTALLATION Step 1. Select Location Gun Case/Safe Large Screen TV Paintings Computers Jewelry Box Valuables Avoid sources of vibration (i.e. speakers, fans, motors) Choose a stable, clean, flat surface Mount in an inconspicuous area. Step 2. Select Operating Mode (refer to table 1) LOOP 1 is for High Security (Fast Trigger) applications and should ONLY be used if the asset will NOT be subject to external vibration. Loop 2 (Standard Security mode) should be used in most cases. FAULT LOOP 1 LOOP 3 30 O O 30 LOOP 3 Painting 1-3 Seconds OR NORMAL High Security (Fast Trigger) Mode (Loop 1) MOUNT HORIZONTALLY ONLY (LOOP 3 ONLY) Jewelry Box O LOOP 2 30 O Greater than 30 LOOP 3 Large Screen 5-8 Seconds TV Standard Security Mode (Loop 2) Tilt Mode (Loop 3) Step 3. Program Device (refer to Programming Section) 2. Enter Zone Number, Zone Type, SENSOR Input Type at Keypad TAB Enroll Serial Number (press tamper switch) PULL TO CONNECT BATTERY Pull tab Enter Loop Number at Keypad (use Loop 2 unless Fast Trigger 1. Pull tab to activate battery or Tilt is required) Step 4. Install Device Peel here (Asset) Mounting Surface 4. Press down firmly for 5 sec. 2. Peel tape backing before installing. Place onto asset. Step 5. Test System 1. Clean mounting surface (refer to mounting notes) 3. Rotate into position
- 2. GENERAL INFORMATION When configured for use with the UL approved control panels (refer to UL Approved Compatible Control UL Panel list), the panel must be programmed not to transmit off-premises for the 5870API zone only. PROGRAMMING For commercial applications, the 5870API must be UL used in conjunction with the 5881ENHC receiver and compatible control panel. 5870API is for use on objects that do not move frequently or vibrate. Mounting the sensor near sources of vibration may cause false alarm conditions to occur. OPERATING MODES If the asset being protected will not be moved under normal circumstances (i.e., a painting), it can be programmed as a 24 hour zone type. If the asset will • occasionally be moved when the system is disarmed, • it can be programmed as a perimeter zone type. • MOUNTING Loop 1 is for high security applications and should ONLY be used if the asset will NOT be subject to external vibration. Loop 2 (Standard Security mode) should be used in most cases. Selecting the Operating Mode When installing the 5870API, select an area on the asset that is stable, clean and flat. Avoid areas that Tamper Supervision are subject to vibration (i.e.; speaker grills) When using Loop 3 the device must be mounted horizontally. OPERATION Table 1 - 5870API Operating Mode Choices Operating Mode Loop Faults when… Restores when… -2-
- 3. REPLACING THE BATTERY MOUNTING NOTES 3M VHB double –sided tape can be used on the following surfaces: acrylic, polycarbonate, coated polycarbonate, cellulose acetate butyrate, aluminum, acrylic/polyurethane paint, galvanized, stainless and UL enameled steel, rigid PVC, epoxy, polyester and epoxy polyester paint, uncoated and silane coated glass, glass epoxy, polybutylene terephthalate, nylon, noryl (PPE) polyphenelene ether, and acrylonitrile Replace the battery with Ademco 469, Panasonic CR2 butadiene styrene. or Duracell DLCR2.Use of another battery may present the risk of fire or explosion Note: Most consumer electronics with plastic cases are manufactured from acrylonitrile butadiene styrene (ABS). INSERT TIP OF SCREWDRIVER. PUSH IN TO RELEASE CLIP 5870API-005-V0 Figure 1 – Replacing the 5870API Battery • 5870API is not watertight, and therefore should not be used in damp locations. • The device should not be installed in locations where temperatures may drop below 14° F. • 5870API is not intended for use on swinging doors. 5870API-001-V0 Figure 2 – Replacing the 5870API Battery 1.7" SPECIFICATIONS TAMPER 1.8" 14° to 122°F (-10° to 50°C) <90% RH (non-condensing) 5870API (Rear View) 5870API-003-V1 -3-
- 4. UL APPROVED COMPATIBLE CONTROL PANELS WARNING °° TO THE INSTALLER FCC and Industry Canada Statement WARRANTY INFORMATION For the latest warranty information, please go to: www.honeywell.com/security/hsc/resources/wa U.S. Patent Number 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 Copyright © 2010 Honeywell International Inc. www.honeywell.com/security K14379V2 1/10 Rev. A