Installation Guide and Detailing Options for Compliance with ASTM C1780

for Adhered Manufactured Stone Veneer
4th
Edition 1st
Printing
Installation Guide
and Detailing Options
for Compliance
with ASTM C1780

2
Masonry Veneer Manufacturers Association
www.masonryveneer.org
April 30, 2014 Installation Guide for Adhered Manufactured Stone Veneer, 4th
Edition 1st
Printing
Table of Contents
Definitions/Abbreviations....................................................................................................................................................................................4
References...............................................................................................................................................................................................................4
Summary Tables....................................................................................................................................................................................................5
Workmanship........................................................................................................................................................................................................7
Material Requirements.........................................................................................................................................................................................7
Surface Preparation...............................................................................................................................................................................................8
Installation of Adhered Manufactured Stone Veneer.....................................................................................................................................10
Cautions................................................................................................................................................................................................................12
Drawings / Cross Sections
Figure 1. Installation Over Wood Framing.....................................................................................................................................................13
Figure 2. Installation Over Concrete Masonry Units...................................................................................................................................14
Figure 3. Wall Assembly....................................................................................................................................................................................15
Figure 4. Typical Wall Section..........................................................................................................................................................................16
Figure 5. Foundation Wall Base........................................................................................................................................................................17
Figure 6 . Foundation Wall Base-AMSV Overlapping Foundation..............................................................................................................18
Figure 7. Foundation Wall-Transition to AMSV Continuing Down Foundation.....................................................................................19
Figure 8. Cladding Transition...........................................................................................................................................................................20
Figure 9. Outside Corner...................................................................................................................................................................................21
Figure 10. Inside Corner....................................................................................................................................................................................22
Figure 11. Horizontal Transition.......................................................................................................................................................................23
Figure 12. Vertical Transition............................................................................................................................................................................24
Figure 13. Open Eave-Overhang.......................................................................................................................................................................25
Figure 14. Open Eave-Flush...............................................................................................................................................................................26
Figure 15. Rake-Overhang.................................................................................................................................................................................27
Figure 16. Rake-Flush........................................................................................................................................................................................28
Figure 17. Side Wall-Composition Shingles...................................................................................................................................................29
Figure 18. Side Wall-Composition Shingles Curbing....................................................................................................................................30
Figure 19. Side Wall-Tile Roofing....................................................................................................................................................................31
Figure 20. Side Wall-Tile Roofing Curbing.....................................................................................................................................................32
Figure 21. Window Sill......................................................................................................................................................................................33
Figure 22. Window Jamb...................................................................................................................................................................................34
Figure 23. Window Head..................................................................................................................................................................................35
Figure 24. Kick-Out Flashing............................................................................................................................................................................36
Figure 25. Cricket...............................................................................................................................................................................................37
Figure 26. Chimney Chase................................................................................................................................................................................38
Figure 27. Column Base....................................................................................................................................................................................39
Figure 28. Raised Column Base........................................................................................................................................................................40
Figure 29. Penetration, Flanged.........................................................................................................................................................................41

3
April 30, 2014Installation Guide for Adhered Manufactured Stone Veneer, 4th
Edition 1st
Printing
National Concrete Masonry Association
13750 Sunrise Valley Drive
Herndon, VA 20171
Phone: (703) 713-1900
www.ncma.org
This Guide addresses generally accepted
methods and details for the installation of
Adhered Manufactured Stone Veneer. To the
best of our knowledge, it is correct and up
to date. However, the document is designed
only as a guide; and it is not intended for any
specific construction project. The MVMA and
NCMA makes no express or implied warranty
or guarantee of the techniques, construction
methods or materials identified herein.
It is understood that there are alternative
means or methods that might be required and/
or recommended based on project conditions,
manufacturer’s recommendations, or product
characteristics.
This Guide for builders, architects, designers,
masons, installers and other construction
professionals illustrates typical applications of
Adhered Manufactured Stone Veneer. Details
in this guide that address the installation and
detailing of Adhered Manufactured Stone
Veneer and its interface with other building
components are not intended as specific
recommendations. It is the responsibility of
all design and construction professionals to
determine the applicability and appropriate
application of any detail to any specific project.
Disclaimer
Copyright © 2014 by the National Concrete
Masonry Association. All rights reserved. 1st
printing
About
Masonry Veneer Manufacturers
Association (MVMA), an affiliate
of NCMA, represents the adhered
manufactured stone veneer industry’s
manufacturing companies and their
suppliers. The mission of the organization
is to advance the growth of the
manufactured masonry veneer products
industry through proactive technical,
advocacy, and awareness efforts.
Table of Contents (continued)
Drawings / Cross Sections (continued)
Figure 30. Penetration Non-Flanged, with Building Paper WRB...................... 42
Figure 31. Penetration Non-Flanged, with Housewrap WRB............................ 43
Figure 32. Penetration, Fixture............................................................................... 44
Figure 33. Penetration, Dryer Vent........................................................................ 45
Figure 34. Deck Termination.................................................................................. 46
Figure 35. Wall Cap.................................................................................................. 47
Figure 36. Wall Assembly-Optional Rainscreen System-Drainage System...... 48
Figure 37. Wall Assembly-Optional Rainscreen System-Strapped.................... 49
Figure 38. Foundation Wall Base-Optional Rainscreen System......................... 50
Figure 39. Typical Wall Section-Optional Rainscreen System........................... 51
Figure 40. Retaining Wall (CMU).......................................................................... 52
Figure 41. Wall-Section Interior Over Cement Backer Board........................... 53
Figure 42. Forward Mounted Commercial Window........................................... 54
Figure 43. Forward Mounted Commercial Window-Top View......................... 55
Figure 44. Commercial Storefront Window-Top View....................................... 56
Figure 45. Commercial Storefront Window......................................................... 57
Figure 46. Wall-Section Multi-Floor Joint Detail................................................. 58
Figure 47. Wall-Section Over Rigid Insulation with Additional Sheathing..... 59
Figure 48. Wall-Section Over Continuous Rigid Insulation CMU................... 60
Figure 49. Wall-Section Inside Corner with Stucco-Top View.......................... 61
Figure 50. Wall-Section Insulated Concrete Form (ICF)-Top View.................. 62
Figure 51. Wall-Section Over Continuous Rigid Insulation with
Z Channels-Top View.......................................................................... 63
Figure 52. Wall-Section Over Continuous Rigid Insulation.............................. 64
Figure 53. Wall-Section Parapet with Stone Cap................................................. 65
Figure 54. Wall-Section Parapet with Steel Cap................................................... 66
Notes....................................................................................................................... 67

4
Edition 1st
Printing
Adhered Manufactured Stone Veneer (AMSV) — lightweight,
architectural, non load-bearing product that is manufactured by
wet cast blending cementitious materials and aggregates, with or
without pigments, admixtures, or other materials to simulate the
appearance of natural stone and other masonry materials.
Note: The MVMA recognizes there are many names used
to describe Adhered Manufactured Stone Veneer products.
Adhered Manufactured Stone Veneer is used commonly
throughout the industry and by some manufacturers. In the
International Building Code, Adhered Manufactured Stone
Veneer products are referred to as Adhered Masonry Veneer.
In the ICC-ES Acceptance Criteria, AC51, the product
is called Precast Stone Veneer. This guide will use AMSV
(Adhered Manufactured Stone Veneer) when referencing the
product.
Backup – The interior or exterior assembly to which AMSV
systems are installed.
CMU – Concrete masonry unit.
Coating – A material applied to the surface of an AMSV
assembly following construction for aesthetic purposes or to
enhance one or more physical properties, such as resistance to
staining or moisture penetration.
Corrosion (Degradation) Resistant – A material that is
intrinsically resistant to degradation or physically or chemically
treated to be so under expected exposure conditions. Examples
include plastic-based materials stabilized for exposure to UV
light, galvanized ferrous metals, and stainless steel.
Fasteners — Corrosion resistant hardware used to secure lath,
screed, and flashing materials to backup system.
Flashing — Corrosion resistant material used to restrict the
seepage of water around any intersection or projection of
materials in an assembly.
Lath — Corrosion resistant mesh building material fastened to
the substrate to act as base for adhering mortar.
Mortar — A mixture of cementitious material, water, and
aggregate, with or without the addition of admixtures or
additives to alter one or more plastic or hardened properties,
used to bond masonry construction materials together and fill
spaces between.
Pointing Mortar — Mortar mixture used to fill joints and
cavities in AMSV construction, also called grouting mortar.
Mortar Scratch Coat — Base coat of mortar used during
the installation of AMSV; cross-raked to improve bond of
subsequent mortar layers.
Mortar Screen — Sheet material installed to prevent the mortar
scratch coat from filling the drainage space behind the AMSV
assembly.
Mortar Setting Bed — Mortar used to adhere the AMSV to the
substrate or scratch coat.
Water Resistive Barrier (WRB) — Material used to restrict the
transmission of water to the surface behind.
Definitions Abbreviations
Blk’g — Blocking
Lbs. — Pounds
Mfr’s — Manufacturer’s
Min. — Minimum
P.T. — Pressure treated (wood preservative)
Req’d — Required
SAF — Self Adhering Flashing
References
AC38 — ICC-ES Acceptance Criteria for Water Resistive Barriers
AC51 — ICC-ES Acceptance Criteria for Pre-Cast Stone Veneer
AC275 — ICC-ES Acceptance Criteria for Glass Fiber Lath used in
Cementitious Exterior Wall Coating or Exterior Cement Plaster (Stucco)
ANSI Accredited Evaluation Service — An ANSI accredited (or
equivalent) third-party organization that issues an evaluation report
affirming a specific building product meets building code requirements.
International Code Council — Evaluation Service (ICC-ES) — An
organization that performs technical evaluations on building products,
components, and construction methods for building code compliance.
In the case where the building code is silent or ambiguous as to a
product’s requirements or a specific construction method, ICC-ES may
develop “Acceptance Criteria” (AC) for the product or construction
method. www.icc-es.org
International Building Code (IBC) — Building code that provides
minimum requirements for safety, health, and welfare of life and property
from hazards of the built environment. The provisions of this code apply
to the construction, alteration, addition, replacement, repair, use and
occupancy of all buildings except one and two family dwellings, and single-
family townhomes not more than three stories in height. www.iccsafe.org
International Residential Code (IRC) — Building code that provides
minimum requirements for safety, health, and welfare of life and property
from hazards of the built environment. The provisions of this code apply
to the construction, alteration, addition, replacement, repair, use and
occupancy of detached one and two family dwellings and single-family
townhomes not more than three stories in height. www.iccsafe.org
ANSI — American National Standards Institute, www.ansi.org
ANSI A118.1 — American National Standards Institute Specifications for
Dry-Set Portland Cement Mortar
ANSI A118.4 — American National Standards Institute Specifications for
Modifed Dry-Set Cement Mortars
ANSI A118.15 — American National Standards Institute Specifications
for Improved Modified Dry-Set Cement Mortar
TMS 402 — Building Code Requirements for Masonry Structures (TMS
402/ACI 530/ASCE 5). This standard is produced through the joint efforts
of the American Concrete Institute (ACI), the Structural Engineering
Institute of the American Society of Civil Engineers (SEI/ASCE), and The
Masonry Society (TMS). Also referred to as the Masonry Standards Joint
Committee (MSJC) Code. www.masonrysociety.org.

5
Edition 1st
Printing
TMS 602 — Specification for Masonry Structures (TMS 602/ACI
530.1/ASCE 6). This standard is produced through the joint efforts of
the American Concrete Institute (ACI), the Structural Engineering
Institute of the American Society of Civil Engineers (SEI/ASCE), and The
Masonry Society (TMS). Also referred to as the Masonry Standards Joint
Committee (MSJC) Specification. www.masonrysociety.org.
Foam Sheathing Committee of the American Chemistry Council, Guide
to Attaching Exterior Wall Coverings Through Form Sheathing to Wood
or Steel Wall Framing. www.FSC.AmericanChemistry.com
ICRI — International Concrete Repair Institute, Technical Guideline
No. 310.2. www.icri.org
ASTM International — ASTM is a developer of technical standards for
products, systems, and services. www.astm.org
ASTM C270 — Standard Specification for Mortar for Unit Masonry
ASTM C482 — Standard Test Method for Bond Strength of Ceramic
Tile to Portland Cement Paste
ASTM C847 — Standard Specification for Metal Lath
ASTM C932 – Standard Specification for Surface Applied Bonding
Compounds for Exterior Plastering
ASTM C933 – Standard Specification for Welded Wire Lath
ASTM C979/C979M – Standard Specification for Pigments for
Integrally Colored Concrete
References (continued)
ASTM C1032 — Standard Specification for Woven Wire Plaster Base
ASTM C1059/C1059M – Standard Specification for Latex Agents for
Bonding Fresh to Hardened Concrete
ASTM C1063 — Standard Specification for Installation of Lathing and
Furring to Receive Interior and Exterior Portland Cement Based Plaster
ASTM C1325 — Standard Specification for Non-Asbestos Fiber-Mat
Reinforced Cementitious Backer Units
ASTM C1384 – Standard Specification for Admixtures for Masonry
Mortars
ASTM C1670 – Standard Specification for Adhered Manufactured
Stone Masonry Veneer Units
ASTM C1714/C1714M – Standard Specification for Preblended Dry
Mortar Mix for Unit Masonry
ASTM C1780 – Standard Practice for Installation Methods for Adhered
Manufactrured Stone Masonry Veneer
ASTM E2556/E2556M — Standard Specification for Vapor Permeance
Flexible Sheet Water-Resistive Barriers Intended for Mechanical
Attachment
ASTM D226/D226M — Standard Specification for Asphalt Saturated
Organic Felt Used in Roofing and Water Proofing
Summary Tables
Wall System
Water Resistive
Barrier
Lath Fastening Scratch Coat
Wall Type
Wood or steel stud.
Spacing of studs no
more than 16 inch
(406 mm) on center.
Rigid Sheathing:
Gypsum wall board
Plywood
OSB
Cement Board*
Fiber Board
Note: Continuous
insulation installed
over rigid sheathing is
limited to a maximum
of 1
/2 inch (13 mm)
thickness.
Minimum of two
separate WRB layers. See
Water Resistive Barrier,
Discussion Section.
Minimum
2.5 lb/ft2
(1.4 kg/m2
)
or 3.4 lb/ft2
1.8 kg/m2
)
self-furring corrosion
resistant lath (ASTM
C847)
Or
18 gauge woven wire
mesh (ASTM C1032)
or heavier
Or
Alternate lath
acceptable with a
product evaluation
acceptance report
showing compliance
to ICC-ES AC 275.
Corrosion resistant
fasteners (ASTM
C1063) minimum
3
/4 inch (19 mm) nail
penetration into wood
framing member,
or minimum 3
/4
inch (19 mm) staple
penetration into wood
framing member,
or minimum 3
/8 inch
(9.5 mm) penetration
of metal framing
member.
Mortar, nominal 1
/2
inch (13 mm) thick. See
mortar section in this
Guide for additional
information and
permitted mortar types.
“Scratch” surface when
somewhat firm.
*See additional installation options for AMSV over cement board in the interior applications discussion.

6
Edition 1st
Printing
Wall System
Water Resistive
Barrier
Clean Concrete,
Masonry / CMU, Stucco
Scratch Coat (1st
layer
of cement plaster), or
Stucco Brown Coat
(2nd
layer of cement
plaster).
Note: walls / surfaces
must be clean and free
from release agents,
paints, stains, sealers,
or other bond-break
materials that may
reduce strength of
mortar adhesion.
Note: A WRB may be
needed to prevent
moisture from
penetrating the wall.
Install lath if there is a
question or concern
regarding ability of
veneer to adhere to
wall (see additional
discussion under
Surface Preparation
Section):
2.5 lb (1.1 kg) or
3.4 lb (1.5 kg)
self-furring 3
/8 inch
(9.5 mm) ribbed
corrosion-resistant
lath (ASTM C 847 )
Or
18 gauge woven wire
mesh (ASTM C 1032)
Alternate lath
acceptable with a
product evaluation
acceptance report
showing compliance
to ICC-ES AC 275.
If lath is applied, use
corrosion resistant
fasteners (ASTM 1063).
If a scratch coat is
required use a nominal
1
/2 inch (13 mm) thick.
See mortar section
in this Guide for
additional information
and permitted mortar
types.
somewhat firm.
Summary Tables (continued)
Wall System
Water Resistive
Barrier
Existing Concrete,
Masonry / CMU,
Stucco, or Brick
(structurally sound)
(e.g. painted or not
clean)
If the wall system is
effectively cleaned and
with adequate surface
roughness, see the
table above.
Note: A WRB may be
needed to prevent
moisture from
penetrating the wall.
2.5 lb (1.1 kg) or
3.4 lb (1.5 kg)
self-furring 3
/8 inch
(9.5 mm) ribbed
corrosion-resistant
lath (ASTM C847)
Or
18 gauge woven wire
mesh (ASTM C1032)
Alternate lath
acceptable with a
product evaluation
acceptance report
showing compliance
to ICC-ES AC 275.
Use corrosion resistant
fasteners (ASTM
C1063).
Nominal 1
/2 inch
(13 mm) thick. See
mortar section in this
Guide for additional
information and
permitted mortar types.
somewhat firm.
Wall System
Water Resistive
Barrier
Metal Buildings or
other surfaces / wall
construction not
listed above. See
manufacturer for
recommendations
regarding sheathing.
See manufacturer for
recommendations.

7
Edition 1st
Printing
This guide focuses on the installation of AMSV systems for backup
assemblies addressed in the tables above. Other backup systems,
suchasstructuralinsulatedpanels(SIPs),mayrequireaspecifically-
designed system of installation for AMSVs. AMSV systems should
not be installed over deteriorating or unsound backup assemblies or
exterior insulation and finishing systems (EIFS).
Workmanship
This Installation Guide assumes that construction personnel
have knowledge of the materials described and their proper
methods of installation.
Prior to commencing activity related to the scope of this Guide,
review all adjacent products and other work that precedes the
installation of AMSV to ensure that proper workmanship is
reflected and that there are no recognizable errors or deficiencies.
Quality
A successful project requires the use of quality materials, proper
detailing for the application, and a high standard of care during
installation. Unfortunately, the execution of these components in
the field can be subject to value-engineering resulting in materials
being selected based solely on price and installation techniques
that focus on speed rather than quality. While the performance of
AMSV systems depends upon all three of these components, field
workmanship issues tend to be the dominate source of problems
when performance issues surface in the field. Installing AMSV in
accordance with the recommended practices of this guide and
ASTM 1780 helps to ensure AMSV systems perform as intended
for decades.
Building Code Requirements
Building code requirements vary from area to area. Check with
local authorities for building code requirements for your area and
application. Carefully read all sections of this guide and follow the
manufacturer’s installation instructions before proceeding with
yourAMSVapplication.Intheeventthemanufacturer’sinstallation
instructions conflict with the intent of statements made in this
document, contact the manufacturer for additional guidance.
Project Site Requirements
Jobsite safety is outside of the scope of this guide, however,
users should always follow proper job site safety requirements
including local, state, and federal laws when installing AMSV
products and systems.
Material Requirements
Flashing
All flashing and flashing accessories must be corrosion resistant
and integrated with the WRB materials (if present). For exterior
applications flashing must be installed at all through wall
penetrations and at terminations of AMSV installations. Flashing
is not required for interior applications of AMSV systems not
exposed to water. For interior applications that are exposed to
water, treat as an exterior assembly.
Rainscreen Drainage Plane Systems
Rainscreens are optional building techniques that are used to
improve the drainage of incidental water behind the cladding and
reduce drying time. Rainscreen products (such as drainage mats
or formed polymer sheeting) or construction techniques (such
as strapping or furring) that create a capillary break/air space
between the cladding and the primary water resistive barrier
can be effectively incorporated into AMSV applications. Refer
to the manufacturer’s recommendation for rainscreen / drainage
system applications with adhered manufactured stone veneer
wall systems. Building codes may allow a single layer of a water
resistive barrier when a drainage space is incorporated in the
wall system (i.e. rainscreen). Requirements for rainscreens vary
by region. Verify local jurisdictional requirements regarding the
use and application of rainscreens.
Weep Screeds and Casing Beads
Weep screeds and casing beads must be corrosion resistant, with
weep screeds having a minimum vertical attachment flange of
3.5 inches (89 mm) that terminates behind the water resistive
barrier (if present). The minimum thickness of metal weep
screeds and casing beads should not be less than 0.0179 inches
(0.45 mm) (26 gage) or less than 0.050 inches (1.3 mm) for
plastic weep screeds or casing beads.
Lath
Multiple lath materials have been used successfully for the
installation of AMSV systems, including:
• 2.5 lb/yd2
(1.4 kg/m2
) (or heavier) self-furring metal lath
meeting ASTM C847;
• 3
/8 inch (9.5 mm) rib (high rib), 3.4 lb/yd2
(1.8 kg/m2
) (or
heavier), self-furring metal lath meeting ASTM C847;
• Welded wire lath complying with ASTM C933;
• 18 gauge(or heavier) woven wiremesh meetingASTM C1032;or
• The lath product is consistent with the AMSV manufacturer’s
installationinstructionsandhasanevaluationacceptancereport
from an accredited evaluation service showing compliance with
ICC-ES Acceptance Criteria 275 (AC275), or equivalent.
All lath and lath accessories must be corrosion resistant, consisting
of either galvanized or stainless steel materials or consisting of
materials complying with AC 275. All lath material must be self-
furred or use self-furring fasteners. Refer to the Summary Table of
this guide for specific lath and fastener recommendations.
Fasteners
Corrosion resistant fasteners are used to secure flashing and
lath to the backup system. A variety of fasteners are available

8
Edition 1st
Printing
such as staples, screws, and nails, provided the heads or
washers of these fasteners are large enough to not pull through
the lath and the fastener is of sufficient length to penetrate into
the supporting material. For specific fastener selection criteria,
refer to ASTM C1063.
• Wood framing - Corrosion resistant staples, corrosion
resistant roofing nails, or corrosion resistant screws and
washers, of sufficient length to penetrate a minimum of 3
/4
inch (19 mm) into framing members.
• Metal framing or panels - Corrosion resistant, self-tapping
screws with sufficient length to penetrate 3
/8 inch (9.5 mm)
through metal studs or panels.
• Masonry or concrete walls or panels - Corrosion resistant
concrete screws or powder actuated fasteners (or cap fastener).
Mortar
Mortars used for the installation of AMSV systems can grouped
into three different categories; scratch coat, setting bed, and
pointing mortars. Depending upon the type of mortar used
and whether it is batched on site or delivered premixed to the
project, each mortar must meet minimum requirements as
described below:
• Scratch Coat Mortars – Scratch coat mortars are applied
directly to the lath or substrate to which AMSV systems
are adhered. As the name implies, this first layer of mortar
is intentionally scratched or roughened before hardening to
provide enhanced mechanical bond between the scratch coat
and setting bed mortars.
o Site Mixed: Meeting the requirements of ASTM C270
Type N or Type S.
o Preblended: Meeting the requirements of ASTM C1714/
C1714M Type N or Type S.
• Setting Bed Mortars – After the scratch coat mortar has cured
sufficiently, the setting bed mortar is used to adhere the AMSV
units to the backing. The setting bed mortar is applied directly
to the scratch coat, to the back of the AMSV units (back-
buttering), or a combination of both application methods.
Type N or Type S.
o Prepackaged/Preblended: Meeting the requirements of
ASTM C1714/C1714M Type N or Type S, ANSI A118.1,
ANSI A118.4, or ANSI A118.15.
• Pointing Mortars – Pointing mortars, also referred to as
grouting mortars or mortar used to grout mortar joints, are
used to fill the joints between individual AMSV units once
the setting bed mortar has sufficiently cured. Not all AMSV
systems incorporate mortar between the units, while others
allow the distance between units to be varied to create
alternative architectural finishes.
Type N or Type S.
o Premixed: Meeting the requirements of ASTM C1714/
C1714M Type N or Type S.
In some cases additives or admixtures are added to mortars to
modify one or more plastic or hardened properties of the mortar;
for example to increase mortar workability, to increase water
repellency characteristics of the mortar, or to increase the bond
strength of the mortar. Mortars specified to comply with either
ASTM C270 or ASTM C1714/C1714M that contain such modifiers
must also comply with the additional requirements of ASTM
C1384. If used, bonding agents must also comply with ASTM
C932 or ASTM C1059 and coloring pigments must comply with
ASTM C979/C979M. As not all mortar additives are compatible
or interchangeable, consult with mortar or additive manufacturers
to ensure compatibility of mortar and admixture components.
Additional Mortar Considerations
When considering mortar selections, verify the mortar can
provide a minimum shear bond strength of at least 50 lb/in.2
(345
kPa) when tested in accordance with ASTM C482, is consistent
with the stone manufacturer’s recommendations, and is suitable
for installation of adhered concrete masonry veneer. Prepackaged/
preblended mortars should be mixed and installed per mortar
manufactures instructions.
Mortars mixed with higher amounts of cement will tend to be less
workable and may be prone to increased shrinkage cracking, but
will provide greater bond strength. Type N mortars are generally
easier to work with than Type S mortars due to the higher cement
content of Type S mortars.
The above setting bed mortar mixes are suitable for most veneer
installations; however polymer modified mortars and mortars
complying with ANSI A118.4 or ANSI A118.15 achieve higher
bond strengths than traditional unmodified ASTM C270 Type S or
Type N mortar. Modified mortars are better suited for challenging
installations or where increased bond strength is desired.
Examples of these installations include, but are not limited to:
tight-fit applications, tilt-up construction, direct bond to concrete
masonry, direct bond to cement board, or hot weather conditions.
Surface Preparation
Verify that the surface to which the AMSV is to be installed is
structurally sound, free of any coatings or materials that would
inhibit bonding, and capable of supporting the intended AMSV
system. The majority of the discussion and details in this guide
focuses on the installation of AMSV systems on backup systems
consisting of wood or steel framing with rigid sheathing and
concrete or concrete masonry construction; however, virtually any
backup system can be used when properly designed and prepared
to receive AMSV systems. Additional considerations are reviewed
in the following discussion.
Masonry walls, poured-in-place concrete walls, and concrete
tilt up panels must be free of dirt, waterproofing, paint, form oil,
or any other substance that could inhibit the mortar bond and
must readily accept/absorb water in order to achieve good bond.
The International Concrete Repair Institute, (ICRI), provides
guidance for concrete surface preparation and assessment. The
surfaces intended to receive AMSV units must have a rough

9
Edition 1st
Printing
texture to ensure good mortar bond. Refer to ICRI Technical
Guideline 310.2 for additional information on concrete surface
preparation, including information on Concrete Surface Profile
(CSP), a standardized method to measure concrete surface
roughness. A CSP equal to or greater than 2 is usually acceptable
for the installation of AMSV over concrete and masonry
assemblies. If necessary, cleaning may be done with power
washing or mechanical methods (i.e. shot or bead blasting). If
a bondable surface cannot be achieved, attach lath and scratch
coat before installing AMSV.
This guide does not address the installation of AMSV systems
over open stud backup systems. Additional information on the
use of AMSV systems in conjuction with open stud construction
is available in previous editions of this guide.
Wall Systems with Exterior Continuous
Insulation
AMSV may be installed on walls insulated with continuous
insulation such as foam insulation. Lath attachment methods
described in this guide are generally considered acceptable
when AMSV is installed over continuous insulation up to
1
/2 inch (13 mm) thick. Installation of AMSV over continuous
insulation greater than 1
/2 inch (13 mm) thick generally requires
an engineered fastening system.
The Foam Sheathing Committee of the American Chemistry
Council (www.americanchemistry.com) has published a "Guide
to Attaching Exterior Wall Coverings through Foam Sheathing
to Wood or Steel Wall Framing" that may provide guidance
when engineering a fastening system for AMSV (http://fsc.
americanchemistry.com/Building-Code/Installation-of-
Cladding/Guide-to-Attaching-Exterior-Wall-Coverings.pdf).
Water Resistive Barrier
Where a water resistive barrier (WRB) is required, it should
be installed in two separate layers in shingle fashion, starting
from the bottom of the wall. The inner layer of WRB should be
installed, along with flashings, to create a drainage plane. The
outer layer of WRB is intended to keep the scratch coat from
contacting the inner layer of WRB. The upper layer of the WRB
should lap on top of the lower layer by a minimum of 2 inches
(51 mm). The vertical joints of the WRB should be lapped a
minimum of 6 inches (152 mm). Inside and outside corners
must be overlapped a minimum of 16 inches (406 mm) past
the corner in both directions. The WRB should be installed in
accordance with the manufacturer’s recommendations and be
integrated with all flashing accessories, adjacent WRBs, doors,
windows, penetrations, and cladding transitions.
Acceptable WRBs:
• Minimum two separate layers of any of the following: No. 15
felt complying with ASTM D226 for Type 1 felt, Grade D paper
complying with ICC-ES AC38, house wrap complying with
ICC-ES AC38, WR complying with ASTM E2556/E2556M, or
any combination of two separate layers of these materials. One
layer of paper-backed lath meeting requirements for Grade D
paper may be substituted for the outer layer.
• Continuous insulation may be substituted for the inner layer
of WRB provided it is installed and sealed and/or taped in
accordance with the insulation manufacturer's installation
instructions and has an evaluation service report from
an accredited evaluation service recognizing it as a WRB.
Continuous insulation is commonly applied on the exterior
side of the framing or on the exterior side of sheathing, runs
continuously, and has minimal thermal bridging. Ensure
WRB(s) selected are intended for wall applications. Some
WRB's intended for roofs are not appropriate for walls. For
example, 15 pound felt is not the same product as No. 15 felt.
Lath
Metal lath should be applied horizontally (perpendicular to
framing, if present) per manufacturer’s instructions, and should
overlap a minimum of 1 inch (25 mm) at the horizontal and
vertical seams. The ends of adjoining lath places should be
staggered. Metal lath is usually installed with the lath "cups"
(keys) facing up. With the cups up, the lath feels rough when
sliding the hand vertically down the wall, and feels smooth when
sliding the hand up the lath.
Lath should be wrapped around inside and outside corners a
minimum of 12 inches (305 mm). Lath should be fastened every
6 inches (152 mm) vertically on each stud or similar spacing on
concrete or masonry wall surfaces. Do not end lath at corner
framing.
Alternate lath should be installed per the manufacturer’s
instructions.
Flashings/Weep Screeds/Casing Bead/
Movement Joints
All flashing and accessory detailing pieces should be corrosion
resistant.
Verify that all flashing, including roofing kickout flashing, has
been properly installed. Although roof flashings are not part of
the wall cladding system, they are necessary for proper water
management. Flashing material should extend above horizontal
terminations, roofing material, and drainage planes or drainage
products.
All flashing material should be integrated with water resistive
barriers to prevent water penetration into structure. The WRB
should overlap the weep screed flange.
Movement Joints - Different elements and materials within
any structure move differently in response to applied loads or
as a result of fluctuations in temperature or moisture content.
In determining if and where movement joints may be needed
as part of an AMSV installation, consideration should be given
to where differential movement is expected—for example, at the
intersection of dissimilar materials; or where movement may be
concentrated—for example, at the transition between a framed
backup assembly and a concrete masonry assembly. Additional
information is available in "Are Control Joints Needed with
Adhered Concrete Masonry Veneer" through MVMA's website:
www.masonryveneer.org.

10
Edition 1st
Printing
Plan ahead with the various trades to integrate flashing and water
resistive barriers to effectively shed water down and out of the wall
system. This may require the preceding trade on the job to install
flashing or WRBs for integration with the next trade on the job.
Clearances
• On exterior stud walls, weep screeds and other base flashings
should be held a minimum of 4 inches (102 mm) above grade
or a minimum of 2 inches (51 mm) above paved surfaces
such as driveways, patios, etc. This minimum can be reduced
to 1
/2 inch (13 mm) if the paved surface is a walking surface
supported by the same foundation supporting the wall.
• On exterior stud walls where the AMSV continues down a
concrete or CMU foundation wall, and where a weep screed
is incorporated into the wall-to-foundation transition, at the
bottom maintain minimum 2 inches (51 mm) clearance from
grade, or 1
/2 inches (13 mm) clearance from a paved surface.
• On exterior stud walls where the AMSV continues down a
CMU foundation wall, with WRB and lath installed down
to the weep screed at bottom, maintain a minimum 4 inches
(102 mm) clearance from grade, or 2 inches (51 mm) clearance
from a paved surface.
• Where AMSV is applied over an exterior concrete or CMU
wall, maintain 2 inches (51 mm) clearance from grade or
1
/2 inches (13 mm) from a paved surface.
• Over an exterior concrete or CMU wall that is not enclosing
conditioned space (e.g. landscape walls, pillars, columns, etc)
maintain a minimum 2 inches (51 mm) clearance from grade
or 1
/2 inches (13 mm) clearance from a paved surface.
Interior Applications
Interior applications in non-wet locations (areas not exposed to
water) for AMSV are similar to exterior applications with the
following alternatives:
• Two layers of WRB are not necessary behind the lath and
scratch coat. A single layer of WRB may protect moisture
sensitive materials during AMSV installation.
• Cement backer board complying with ASTM C1325 may be
substituted for other substrates (i.e. wall board or plywood),
WRB, lath, and scratch coat. The cement backer board should
be installed per the manufacturer’s instruction. The AMSV
should be installed per this guide – see Grouted Adhered
Manufactured Stone Veneer Application or Tight Fitted
Adhered Manufactured Stone Veneer and the Mortar and
Premix Mortar sections. Latex-Portland cement mortars
complying with ANSI A118.4 must be used for installation
of AMSV to cement backer board. Follow the mortar
manufacturer’s instructions.
• Interior applications are not subjected to the same fluctuations
in temperature and moisture as exterior applications. As such,
the criteria for clearances used for exterior applications are
typically not necessary. Nevertheless, differential movement
between different materials must still be accounted for.
• Flashings, weep screeds, and casing beads are not necessary.
Installation of Adhered
Manufactured Stone Veneer
Prior to commencing installation of AMSV, ensure that the
WRB and flashing are properly installed and integrated with
each other. Refer to the flashing details, referenced in this guide,
for detailing around windows, doors, through-wall penetrations,
and AMSV terminations.
Afterthelathisinstalled,applyanominal1
/2 inches(13mm)thick
layer of mortar ensuring the lath is completely encapsulated with
mortar. The mortar should be applied with sufficient pressure
and thickness to fully embed the lath in mortar. Once the mortar
is thumbprint hard, scratch (score) the surface horizontally to
create the mortar scratch coat.
Moist curing the mortar scratch coat will help reduce cracking
and ensure proper hydration during curing. Before applying
AMSV, the mortar scratch coat should be dampened so that the
surface appears wet but free of standing water.
Before installing AMSV, lay out a minimum of 25 square feet
(2.3 m2
) at the jobsite so there is a variety of sizes, shapes, and
colors from which to choose. Mixing AMSV sizes, shapes,
textures and color will allow for variety and contrast in the
design to achieve the desirable finished project. Follow AMSV
manufacturers recommendations regarding mixing of product
to achieve desired results.
The following guidance for grouted and tight-fit application of
adhered masonry veneer applies to conventional Type N and
Type S mortars. If a polymer modified mortar is used, some of
the working properties and installation techniques may vary
from those of conventional Type N or Type S mortars. Consult
the mortar manufacturer for guidance and instructions.
Grouted Adhered Manufactured Stone Veneer
Application
Tip: Installing AMSV from the top down will minimize cleanup
requirements.
Prior to the application of mortar to the scratch coat or the back
of the AMSV, the scratch coat and back of the AMSV should
be moistened so that the surfaces appear damp but are free of
standing water.
The back of each AMSV should be entirely buttered with mortar
to a nominal thickness of 1
/2 inches (12.7mm). Cover the entire
back of the AMSV, not just the perimeter. Buttered AMSV
should be firmly worked onto the scratch coat and slid slightly
back and forth or with a slight rotating motion to set the AMSV.
Polymer modified mortars, complying with ANSI A118.4, may
have a different "feel" than regular/common mortars.
Achieve mortar squeeze out in a volume that results in a full
settingbedcoveringthescratchcoatcompletely.Asanalternative
to the back-butter only method, mortar may be troweled onto
the scratch coat, completely covering the scratch coat. Or both
mortar application techniques may be combined. The resulting
thichness of the scratch coat and setting bed should be nominally
1 inch (25 mm) measured from the outer surface of the WRB to
the back surface of the unit.

11
Edition 1st
Printing
With the proper mortar mix, moisture content, and scratch coat
preparation, the installer will feel the mortar start to grab within
a few seconds of the setting movement process. At this point, no
further movement of that AMSV should be made as bonding
will be broken. If the AMSV is inadvertently moved after initial
set has begun, it should be removed, mortar scraped off the back
of the AMSV and scratch coat, and then reinstalled following the
application process.
Grouting the joints should be completed only after there is
sufficient cure time of the installed AMSV units; when mild
contact with AMSV units will not break the bond to the backup
system. Grouting may be done with a grout bag, filling joints
to the desired depth, ensuring that mortar is forced into all
voids. Grout should be “thumbprint hard” before tooling the
joints. The curing time required before the grout is ready
will vary significantly with temperature and humidity. Use
a wooden raking stick or pointing tool to tool the joints to
the desired depth. Extra precaution should be taken while
tooling so the surface of the AMSV is not damaged. Clean
off remaining grout debris on the AMSV surface with a dry,
soft-bristled brush.
To prevent mortar smearing, DO NOT use a wet brush to treat
uncured mortar joints.
Tight Fitted Adhered Manufactured Stone
Veneer Application
Refer to Mortar section for additional guidance regarding mortar
selection. For this installation technique, refer to the Additional
Mortar Considerations section.
The back of the AMSV and the scratch coat should be moistened
with the surfaces appearing damp but free of standing water.
The back of each AMSV should be entirely buttered with mortar
to a nominal thickness of 1
/2 inch (13 mm). Cover the entire back
of the AMSV, not just the perimeter. Buttered AMSV should be
firmly worked onto the scratch coat and slid slightly back and
forth to set the AMSV.
Achieve mortar squeeze out in a volume that results in a full
setting bed which covers the scratch coat completely. As an
alternative to the back-butter only method, mortar may be
troweled onto the scratch coat, completely covering the scratch
coat. Or both mortar application techniques may be combined.
The resulting thichness of the scratch coat and setting bed should
be nominally 1 inch (25 mm) measured from the outer surface
of the WRB to the back surface of the unit.
With the proper mortar mix, moisture content and scratch coat
preparation, the installer will feel the mortar start to grab within
a few seconds of the setting movement process. At this point, no
further movement of that AMSV should be made as bonding
will be broken. If the AMSV is inadvertently moved after initial
set has begun, it should be removed, mortar scraped off the back
of the AMSV and scratch coat, and then reinstalled following the
application process.
Tight fitted AMSV should be applied from the corners toward
the middle of a wall, and from the bottom toward the top of
the wall.
Cold Weather Application
AMSV applications should be protected from temperatures
below 40°F (4°C) during and immediately following installation.
The use of anti-freeze admixtures to lower the freezing point of
the mortar is not recommended. Accelerating admixtures shall
comply with ASTM C1384; accelerating admixtures containing
calciumchloridearenotrecommended.AMSVpiecescontaining
visible frozen moisture shall not be installed.
The cold weather practices defined in TMS 602 should be
followed for the installation of AMSV systems.
Hot Weather Application
If the environmental conditions during installation exceed 90°F
(32°C) additional water may be needed on the scratch coat
surface and the backs of the AMSV being applied. Providing
shade and/or frequent misting of the wall may be required.
Consult with mortar manufacturer to determine if hot weather
mortar mix options are available. The hot weather practices
defined in TMS 602 should be followed for the installation of
AMSV systems.
Cleaning the Adhered Manufactured Stone
Veneer
Refer to AMSV manufacturer recommendations on cleaning
and maintenance. Do not use harsh chemicals for cleaning,
such as acid, or use abrasive tools such as wire brushes or
power washers.
Coating Adhered Manufactured Stone Veneer
Refer to the AMSV manufacturer for recommendations
regarding the use of sealants or other topically applied coatings
used for water penetration resistance, graffiti resistance, or
surface sealing.
Alternative Installation Methods / Materials
This guide covers common installation practices for AMSV
systems. Alternative installation materials and methods not
included in this guide may be introduced into the marketplace.
Example: Exterior installation methods using cementitious
adhesive mortars with a direct application to a substrate that may
include cement board and / or coatings applied as loadbearing
bonded water-proof membranes.
Alternative installation materials and methods along with their
test methods and evaluation criteria are being developed. As a
designer, contractor, or installer, you may wish to utilize these
materials and/or methods in lieu of the resommended methods
included in this guide. Users should verify that the alternative
method(s) will meet or exceed the recommended installation
practices presented in this guide.

12
Edition 1st
Printing
Refer to manufacturer's recommendations for additional
information regarding the use of alternative installation methods
or materials.
Cautions
The following precautions should be taken to ensure a successful
and durable AMSV installation.
• Do not subject AMSV to direct or frequent water contact.
For example, avoid allowing sprinklers to directly spray
onto the surface. Also, downspouts or drainage pipes
should be placed so that water is not frequently moistening
the AMSV units.
• Do not subject AMSV to contact with de-icing materials,
salt, or other harsh chemicals. Prolonged exposure to these
conditions may discolor the AMSV or result in surface
damage.

13
Edition 1st
Printing
Figure 1. Installation Over Wood Framing
INTERIOR GYPSUM BOARD
BATT INSULATION
WOOD FRAMING
EXTERIOR GRADE SHEATHING
(2) LAYERS OF WRB
LATH
LATH FASTENERS - TYPE &
SPACING PER ASTM C1063
MORTAR SCRATCH COAT
MORTAR SETTING BED
ADHERED CONCRETE MASONRY
VENEER
MORTAR JOINT
WRB LAPPED OVER WEEP
SCREED
WEEP SCREED

14
Edition 1st
Printing
Figure 2. Installation Over Concrete Masonry Units
INTERIOR GYPSUM BOARD
FURRING OR CHANNEL
RIGID INSULATION
JOINT REINFORCEMENT
CMU BACKUP
LATH (OPTIONAL)
LATH FASTENER - TYPE &
SPACING PER ASTM C1063
MORTAR SCRATCH COAT
MORTAR SETTING BED
VENEER
MORTARJOINT
WEEP SCREED (OPTIONAL)

15
Edition 1st
Printing
Figure 3. Wall Assembly
EXTERIOR FINISH
(STUCCO SHOWN)
(2) LAYERS WRB
LAP WRB OVER SCREED
(OR FLASHING)
WEEP SCREED OR
CASING BEAD (OPTIONAL)
EXTEND WRB FROM WALL BELOW 6 IN.
(152 mm) MIN. ABOVE WATER TABLE
FLASHING
BEDDING SEALANT UNDER
FLASHING
MORTAR SCRATCH COAT
MORTAR SETTING BED
ADHERED MANUFACTURED
STONE VENEER
MORTAR JOINT (WHERE USED)
(2) LAYERS WRB
LATH
SHEATHING
BLOCKING (OPTIONAL)

16
Edition 1st
Printing
Figure 4. Typical Wall Section
WALL SYSTEM
SHEATHING
(2) LAYERS WRB
LATH
MORTAR SCRATCH COAT
MORTAR SETTING BED
STONE VENEER
EXTERIORINTERIOR
SECTION VIEW
Note: layering of sheathing, water resistive barrier, lath, scratch coat, and adhered manufactured stone veneer.

17
Edition 1st
Printing
Figure 5. Foundation Wall Base
SHEATHING
(2) LAYERS WRB
LATH
MORTAR SCRATCH COAT
MORTAR SETTING BED
STONE VENEER
FLOOR FRAMING
LAP WRB OVER
WEEP SCREED FLANGE
FOUNDATION WEEP SCREED
EXTEND ADHERED MANUFACTURED
STONE VENEER MIN. 1 IN. (25 mm)
BELOW TOP OF FOUNDATION
2 IN. (51 mm) AT PAVING
4 IN. (102 mm) AT GRADE
SLOPE GRADE
2% MIN.
SECTION VIEW
A minimum 4 in. (102 mm) gap is required at the base of the stud wall to grade and a minimum 2 in. (51 mm) gap is required
at base of the stud wall to a paved surface.

18
Edition 1st
Printing
Figure 6. Foundation Wall Base – AMSV Overlapping
Foundation
AMSV may overlap foundation wall with careful installation of flashing and WRB. This installation may continue down
foundation wall to grade clearance.
FLASHING 6 in. (152 mm)
CMU OR CONCRETE WALL
WATERPROOFING (WHERE REQ'D)
(2) LAYERS WRB
CONTINUED (WHERE REQ'D)
LAP WRB OVER
WEEP SCREED FLANGE
FLASHING6in.(152mm)
SECTION VIEW
SHEATHING
(2) LAYERS WRB
LATH
MORTAR SCRATCH COAT
MORTAR SETTING BED
STONE VENEER
(2) LAYERS WRB

19
Edition 1st
Printing
Figure 7. Foundation Wall –
Transition to AMSV Continuing Down Foundation
AMSV may continue down the foundation with the incorporation of a flashing transition with careful installation of WRB
and flashing.
SHEATHING
(2) LAYERS WRB
LATH
MORTAR SCRATCH COAT
MORTAR SETTING BED
STONE VENEER
LAP WRB OVER FLASHING
SILL SCREED FLANGE
WEEP SCREED, DRIP SCREED, OR
BEDDING SEAL UNDER
FLASHING WITH DRIP EDGE
FLASHING TRANSITION EXTEND
MIN. 1 IN. (25 mm) BELOW TOP
OF FOUNDATION
LATH (WHERE REQ'D)
MORTAR SETTING BED OVER
MORTAR SCRATCH COAT
CMU OR CONCRETE WALL
WATERPROOFING (WHERE REQ'D)
SECTION VIEW
1IN.(25mm)

20
Edition 1st
Printing
Flashing should be installed prior to the adhered manufactured stone. Water resistive barrier laps over the vertical leg of
flashing for positive drainage. Optional support angle shown. Verify installation requirements with adhered manufactured
stone veneer manufacturer.
Figure 8. Cladding Transition
EXTERIOR CLADDING (SIDING SHOWN)
NOTE:
OTHER FINISHES MAY BE USED
(1) LAYER WRB
EXTEND WRB FROM WALL BELOW 6 IN.
(152 mm) MIN. ABOVE CLADDING TRANSITION
BLOCKING (OPTIONAL)
BEDDING SEAL UNDER FLASHING
LATH FASTENER
ADHERED MANUFACTURED STONE VENEER
SUPPORT ANGLE -- INSTALL IF REQUIRED PER
THE STONE MANUFACTURER'S INSTRUCTIONS
MORTAR SETTING BED
MORTAR SCRATCH COAT
(2) LAYERS WRB
LATH
SHEATHING
SECTION VIEW
6IN.(152mm)LAP

21
Edition 1st
Printing
Figure 9. Outside Corner
Randomly alternate short end returns above and below at the corner. Lap lath around the corner to the next framing member.
SHEATHING
BATT INSULATION
(2) LAYERS WRB
LATH -- WRAP LATH AROUND
CORNER TO NEXT FRAMING
MEMBER AND LAP AT FRAMING
MEMBER
MORTAR SCRATCH COAT
MORTAR SETTING BED
ADHERED CONCRETE
MASONRY VENEER
MORTAR JOINT
(WHERE USED)
EXTEND AT LEAST ONE LAYER OF WRB
FROM EACH DIRECTION AROUND
CORNER 12 IN. (305 mm) MIN.
WALL SYSTEM AT CORNER
VENEER ALTERNATE SHORT END
RETURNS ABOVE AND BELOW AT
CORNER
PLAN VIEW

22
Edition 1st
Printing
Figure 10. Inside Corner
Randomly alternate ends above and below to interweave the corner. Double wrap water resistive barrier around both sides of
the corner. Lap lath to the framing at least 12 inches (305 mm) to the next framing member.
ALTERNATE ENDS ABOVE AND BELOW TO
INTERWEAVE CORNER
EXTEND AT LEAST ONE LAYER OF WRB
FROM EACH DIRECTION AROUND
CORNER 12 IN. (305 mm) MIN.
LATH - WRAP LATH AROUND CORNER TO
NEXT FRAMING MEMBER AND LAP LATH AT
FRAMING MEMBER
MORTAR SCRATCH COAT
MORTAR SETTING BED
LATH
(2) LAYERS WRB
SHEATHING
PLAN VIEW

23
Edition 1st
Printing
Figure 11. Horizontal Transition
Note: flashing is lapped shingle-fashion with corrosion resistant sheet metal. A bedding seal is used under the corrosion
resistant sheet metal next to the adhered manufactured stone veneer.
EXTERIOR SHEATHING (SIDING SHOWN)
NOTE: OTHER FINISHES MAY BE USED
(2) LAYERS WRB
FLASHING - PROVIDE END DAM AT
FLASHING TERMINATION
HORIZONTAL WOOD TRIM (PRIMED)
STRIP OF FLASHING - LAP OVER
FLASHING BELOW
BLOCKING FOR LATH EDGE
AND FLASHING
FLASHING - PROVIDE END DAM AT
FLASHING TERMINATION
CASING BEAD (OPTIONAL) OVER WRB
MORTAR SETTING BED
MORTAR SCRATCH COAT
LATH
(2) LAYERS WRB
SHEATHING
EXTENDWRB6IN.(152mm)
ABOVEFLASHING
SECTION VIEW

24
Edition 1st
Printing
Figure 12. Vertical Transition
Flashing extends under the adjacent finishes. A 3
/8 in. (10 mm) minimum gap should be used between finishes.
BLOCKING AT LATH EDGE
FLASHING BEHIND TRIM -
EXTEND UNDER ADJACENT
FINISH AS REQUIRED
ADJACENT FINISH
VARIES
BACKER ROD AND SEALANT
CASING BEAD AT SEALANT JOINT (OPTIONAL)
FLASHING
(2) LAYERS WRB - (1) LAYER UNDER FLASHING
LAP (1) LAYER OVER FLASHING AND CASING
BEAD
SHEATHING
WOOD TRIM (PRIMED)
SIZE AND PROFILE
MAY VARY
3
8 IN. (10 mm)
JOINT
LAP FLASHING
OVER CASHING BEAD
6 IN. (152 mm) MIN.
PLAN VIEW
LATH
MORTAR SCRATCH COAT
MORTAR SETTING BED
STONE VENEER
MORTAR JOINT
(WHERE USED)

25
Edition 1st
Printing
ADHERED MANUFACTURED STONE
VENEER
MORTAR SETTING BED
MORTAR SCRATCH COAT
LATH
(2) LAYERS WRB
SHEATHING
6IN.(152mm)MIN.LAP
FLASHINGOVERWRB
Figure 13. Open Eave - Overhang
Water resistive barrier should be in place prior to soffit installation followed by adhered manufactured stone veneer.

26
Edition 1st
Printing
Figure 14. Open Eave - Flush
Water resistive barrier should be in place prior to soffit installation followed by adhered manufactured stone veneer.
WRB OR FLASHING
USE WOOD STOP OR 1X FILLER
BEHIND FASCIA
OPTION: CASING BEAD OVER
FLASHING
1 IN. (25 mm) MIN. LAP OVER TOP
OF ADHERED MANUFACTURED
STONE VENEER
STONE VENEER
MORTAR SETTING BED
MORTAR SCRATCH COAT
LATH
(2) LAYERS WRB
SHEATHING
6IN.(152mm)MIN.LAP
FLASHINGOVERWRB
SECTION VIEW

27
Edition 1st
Printing
Figure 15. Rake - Overhang
The intent of these details is to limit exposure to wind driven rain.
FLASHING OR WRB STRIP BEHIND TRIM -
LAP OVER (2) LAYERS WRB AT WALL
STONE VENEER
MORTAR SETTING BED
MORTAR SCRATCH COAT
LATH
(2) LAYERS WRB
SHEATHING
SECTION VIEW
4IN.(102mm)MIN.LAP
FLASHINGOVERWRB

28
Edition 1st
Printing
Note: the use of backer rod and sealant.
Figure 16. Rake - Flush
FLASHING OR WRB STRIP BEHIND
TRIM LAP OVER WRB AT WALL
1 IN. (25 mm) MIN. LAP OVER
TOP OF ADHERED MANUFACTURED
STONE VENEER
CASING BEAD OVER (OPTIONAL)
(2) LAYERS WRB - OPTION: USE
WOOD STOP OR 1X FILLER BEHIND
SUB-FASCIA
STONE VENEER
MORTAR SETTING BED
MORTAR SCRATCH COAT
LATH
(2) LAYERS WRB
SHEATHING
4IN.(102mm)MIN.LAP
FLASHINGOVERWRB
SECTION VIEW

29
Edition 1st
Printing
Figure 17. Side Wall – Composition Shingles
Water resistive barrier laps over step flashing and weep screed.
STONE VENEER
MORTAR SETTING BED
MORTAR SCRATCH COAT
LATH
BLOCKING FOR LATH EDGE
AND FLASHING
(2) LAYERS WRB
LAP OVER STEP FLASHING
AND WEEP SCREED
STEP FLASHING AT RAKE
PER ROOF MANUFACTURERE'S
RECOMMENDATIONS
WEEP SCREED - LAP
OVER STEP FLASHING 2 IN.
(51 mm) MIN.
ROOF TYPE MAY VARY -
COMPOSTION SHINGLE
ROOF SHOWN
ROOF UNDERLAYMENT -
TURN UP AT SIDE WALL
2IN.
(51mm)
MIN.
SECTION VIEW

30
Edition 1st
Printing
STONE VENEER
(2) LAYERS WRB
LAP OVER WEEP SCREED
AND COUNTERFLASHING
BLOCKING FOR LATH
EDGE AND FLASHING
WEEP SCREED
COUNTERFLASHING
STEP FLASHING AT RAKE PER
ROOF MANUFACTURER'S
RECOMMENDATION
COMPOSTION SHINGLE
ROOF SHOWN
ROOF UNDERLAYMENT -
1X FILLER - SLOPE TOP
2IN.(51mm)
MIN.
2IN.
(51mm)
MIN.
2IN.
(51mm)
MIN.
Figure 18. Side Wall – Composition Shingles Curbing
This detail includes base trim. Note the counterflashing between trim and adhered manufactured stone veneer.

31
Edition 1st
Printing
STONE VENEER
MORTAR SETTING BED
MORTAR SCRATCH COAT
LATH
BLOCKING FOR LATH
EDGE AND FLASHING
(2) LAYERS WRB
LAP OVER WEEP SCREED
WEEP SCREED OR DRIP
SCREED LAP OVER RAKE
WALL FLASHING
2 IN. (51 mm) MIN.
SIDE WALL FLASHING PER
ROOF MANUFACTURER'S
RECOMMENDATION
TILE ROOF SHOWN
ROOF UNDERLAYMENT -
2IN.
(51mm)
MIN.
DETAIL VIEW
Figure 19. Side Wall – Tile Roofing
Water resistive barrier laps over step flashing and weep screed.

32
Edition 1st
Printing
STONE VENEER
(2) LAYERS WRB - LAP
OVER WEEP SCREED
AND FLASHING
SCREED OR DRIP
SCREED
BLOCKING FOR LATH
EDGE AND FLASHING
COUNTERFLASHING
1X FILLER
SIDE WALL FLASHING
PER ROOF
MANUFACTURER'S
RECOMMENDATION
TILE ROOF SHOWN
ROOF UNDERLAYMENT -
DETAIL VIEW
2IN.(51mm)
MIN.LAP
2IN.
(51mm)
MIN.
Figure 20. Side Wall – Tile Roofing Curbing
This detail includes curbing. Note the counterflashing between trim and adhered manufactured stone veneer.

33
Edition 1st
Printing
WINDOW FRAME
PROFILE MAY VARY - REFER TO
WINDOW MANUFACTURER'S DETAILS
FOR INSTALLATION AND FLASHING
BEDDING SEALANT UNDER WINDOW FIN
(IF REQUIRED PER WINDOW
MANUFACTURER'S INSTRUCTIONS)
SILL FLASHING UNDER WINDOW FIN.
LAP OVER WRB 4 IN. (102 mm) MIN.
3
8 IN. (10 mm)
VENEER WITH SLOPED TOP
MORTAR SETTING BED
STONE VENEER
MORTAR SCRATCH COAT
LATH
WRB UNDER SILL FLASHING
SHEATHING
DETAIL VIEW
AIR SEAL
Figure 21. Window Sill
Rough openings must be properly flashed prior to window installation. Tuck water resistive barrier under flashing at sill. Sill
flashing should drain to the exterior of the primary WRB or to exterior of adhered manufactured stone veneer.

34
Edition 1st
Printing
WINDOW FRAME
PROFILE MAY VARY - REFER TO
WINDOW MANUFACTURER'S DETAILS
FOR INSTALLATION AND FLASHING
JAMB FLASHING UNDER
WINDOW FIN
BEDDING SEALANT UNDER
WINDOW FIN
SHEATHING
(2) LAYERS WRB
SEAL EDGE TO FIN
LATH
MORTAR SCRATCH COAT
MORTAR SETTING BED
STONE VENEER
BEDDING SEALANT UNDER WRB
LAPPED OVER CASING BEAD
CASING BEAD (OPTIONAL) LAP
FLASHING OVER LEG
PLAN VIEW
3
8 IN.
(10 mm)
Figure 22. Window Jamb
Rough openings must be properly flashed prior to window installation. Backer rod and sealant between the window frame
and the adhered manufactured stone veneer allows for movement between the dissimilar materials.

35
Edition 1st
Printing
SHEATHING
(2) LAYERS WRB
LATH
MORTAR SCRATCH COAT
MORTAR SETTING BED
STONE VENEER
VENEER KEY OR TRIM (WHERE OCCURS)
LAP WRB OVER HEAD FLASHING
AND SEAL EDGE
DRIP SCREED OR CASING BEAD
(OPTIONAL)
HEAD FLASHING SET IN SEALANT
(WIDTH TO COVER JAMB TREATMENT)
OPTIONAL BACKER ROD AND SEALANT
BEDDING SEALANT UNDER WINDOW FIN
WINDOW FRAME PROFILE MAY VARY -
REFER TO WINDOW MANUFACTURER'S
DETAILS FOR INSTALLATION AND
FLASHING
3
8 IN. (10 mm)
9IN.(229mm)MIN.FLASHING
OVERHEADFIN
DETAIL VIEW
Figure 23. Window Head
Flashing and WRB installed shingle fashion may be complimented with self-adhered flashing to seal WRB to window frame.

36
Edition 1st
Printing
Figure 24. Kick-Out Flashing
Kickout flashing should be sized properly to accommodate thickness of AMSV. Integration of WRB, flashing and kick-out
critical.
STONE VENEER
ROOFING MATERIAL
(2) LAYERS WRB
LAP OVER SCREED AND
STEP FLASHING
WEEP SCREED
STEP FLASHING AT
ROOFING LAP
OVER KICK-OUT FLASHING
KICK-OUT FLASHING - SEAL
OVER EAVE FLASHING
SHINGLE LAP ALL WALL
FLASHING PIECES WITH WRB
UNDERLAYMENT PER ROOF
MANUFACTURER
EAVE DRIP EDGE FLASHING
GUTTER
WRB STRIP BEHIND TRIM
LAP OVER WRB AT WALL
ISOMETRIC VIEW

37
Edition 1st
Printing
Figure 25. Cricket
TYPICAL CRICKET
PER ROOF MANUFACTURER'S
RECOMMENDATIONS
DETAIL 25.2
EXTEND CRICKET MIN. 2 IN. (51 mm)
BEYOND CHASE
(2) LAYERS WRB
WEEP SCREED
COUNTERFLASHING
STONE VENEER OVER
FRAMED WALL OR CHASE DETAIL 25.3
(2) LAYERS WRB
EXTEND FLASHING 2 IN. (51 mm) BEYOND
CHASE - EACH SIDE TO ACCOMODATE
INSTALLATION OF ADHERED
MANUFACTURED STONE VENEER
SEE DETAIL 23.3
COMPOSITION SHINGLE ROOFING
(OTHER ROOFING SIMILAR)
UNDERLAYMENT OVER ROOF SUBSTRATE -
LAP OVER CRICKET FLANGE
CRICKET - PROVIDE SHEATHING AND
FRAMING SUPPORT AS NEEDED
DETAIL 25.1
DETAIL VIEW
2 IN. (51 mm) MIN.
A cricket up-slope of a roof penetration, such as a chimney, helps direct water around the penetration.

38
Edition 1st
Printing
CHIMNEY CHASE NOTE:
MAINTAIN MINIMUM
CLEARANCE OF
COMPUSTIBLE
MATERIALS PER
CHIMNEY
MANUFACTURER'S
RECOMMENDATIONS
SHIM AS REQUIRED
SOLID SUBSTRATE -
SLOPE 1
4:12, MIN.
SECTION VIEW
METAL CHIMNEY CAP (PER PLAN)
ROOFING UNDERLAYMENT
9 IN. (229 mm) WIDE FLASHING OR
WRB STRIP LAP OVER WRB AT WALL
1X OR 2X BLOCKING AS REQUIRED
3
4 IN. (19 mm) STUCCO KEY
OPTION: USE WOOD STOP OR
CASING BEAD OVER FLASHING
2X TRIM
1 IN. (25 mm) MIN. LAP OVER TOP
OF ADHERED MANUFACTURED
STONE VENEER
DIMENSTION TO CLEAR TOP
OF A.C.M.V.
STONE VENEER
MORTAR SETTING BED
MORTAR SCRATCH COAT
LATH
(2) LAYERS WRB
SHEATHING
Figure 26. Chimney Chase

39
Edition 1st
Printing
Figure 27. Column Base
A minimum one half inch (13 mm) clearance should be maintained at all sides of the base. All column materials to be
exterior grade. Do not extend flashing past edge of AMSV for safety reasons.
SECTION VIEW
LATH
MORTAR SCRATCH COAT
MORTAR JOINT
(2) LAYERS WRB
EXTERIOR GRADE SHEATHING -
MAINTAIN 1 IN. (25 mm) MIN.
ABOVE CONCRETE
FRAMED WALL SYSTEM
WEEP SCREED OR DRIP SCREED
BEDDING SEAL UNDER FLAHSING
1
2 IN. (13 mm) MIN.

40
Edition 1st
Printing
Figure 28. Raised Column Base
Adhered manufactured stone veneer may overlap the raised concrete pad, but a clearance of one half inch (13 mm) should be
maintained at all sides of the base. Do not extend flashing past edge of AMSV.
DETAIL VIEW
RAISED CONCRETE PAD
FRAMED WALL SYSTEM
BEDDING SEAL UNDER FLAHSING
1
2 IN. (13 mm) MIN.
LATH
MORTAR SCRATCH COAT
EXTERIOR GRADE SHEATHING -
MAINTAIN 2 IN. (51 mm) MIN.
ABOVE CONCRETE

41
Edition 1st
Printing
Figure 29. Penetration, Flanged
Penetration with flanges can be incorporated into the wall system by applying WRB in a watershed fashion and sealing cuts in
the WRB with self-adhered flashing. Drawing illustrates installation with housewrap WRB. Installation with building paper
WRB would be similar but instead of 45 degree cuts, fit last piece of WRB on top of flanges and tuck under WRB course
above penetration (similar to Step 2 in Fig. 31.).
CUT WRB DIAGONALLY FROM TOP
CORNERS PENETRATION FLANGE
(1) LAYER WRB
APPLY (1) LAYER
SELF-ADHERED FLASHING
(SAF) OVER WRB UNDER
PENETRATION FLANGE
SEAL DIAGONAL CUTS IN
WRB WITH (1) LAYER SAF
SEAL TOP FLAP OF WRB
APPLY (1) LAYER SAF OVER
TOP FLAP
APPLY (1) LAYER SAF OVER
WRB EACH SIDE AND UNDER
TOP FLAP OF CUT WRB
NOTE:
2ND LAYER OF WRB (OUTER LAYER)
TO BE APPLIED OVER FLANGE AND
FLASHING OF PENETRATION
STEP 1
STEP 2
ISOMETRIC VIEW

42
Edition 1st
Printing
Figure 30. Penetration Non-Flanged, with Building Paper WRB
Flexible self-adhered flashing and WRB installed in a watershed fashion help prevent water infiltration.
UPPER COURSE WRB LAPPED MIN.
2 IN. (51 mm)
(1) LAYER WRB TRIM TO FIT
AROUND PENETRATION
APPLY FLEXIBLE SELF-ADHERED
FLASHING (SAF) AND SEALANT
AROUND PENETRATION
STEP 1
STEP 2
ISOMETRIC VIEW
NON-FLANGED
PENETRATION
LOWER COURSE WRB
(BUILDING PAPER)
TUCK UNDER UPPER COURSE
OF WRB MIN. 2 IN. (51 mm)
(1) LAYER WRB
NON-FLANGED
PENETRATION
(1) LAYER WRB - APPLY OUTER
LAYER WRB OVER FLASHING AT
PENETRATION AND TRIM TO FIT
AROUND PENETRATION

43
Edition 1st
Printing
Figure 31. Penetration Non-Flanged, with Housewrap WRB
Flexible self-adhered flashing around the penetration and WRB lapped in a watershed fashion help prevent
water infiltration.
WRB CUT AT APPROXIMATELY 45° ANGLE UP
FROM PENETRATION HOLD FLAP UP AND
AWAY FOR FLEXIBLE SAF TO BE SEALED AT
PENETRATION
SHEATHING BEHIND
(1) LAYER WRB TRIM TO FIT
AROUND PENETRATION
APPLY FLECIBLE SAF AND (OR)
SEALANT AROUND PENETRATION
NON-FLANGED PENETRATION
(1) LAYER WRB
FLAP OF WRB
FOLDED UP
FLEXIBLE SAF
NON-FLANGED
PENETRATION
STEP 1
STEP2
PLACE FLAP OF WRB ON EXTERIOR
SIDE OF FLEXIBLE SAF - SEA L CUTS
IN WRB WITH SAF
(1) LAYER WRB
APPLY FLECIBLE SAF
SEALING TO PENETRATION
AND WRB
NON-FLANGED PENETRATION
FLAP OF WRB
FOLDED DOWN
ON TOP OF SAF
AROUND PIPE
FLEXIBLE
SAF SEALING
CUTS IN WRB
NON-FLANGED
PENETRATION
FLEXIBLE SAF
NOTE:
APPLY LAYER OF WRB (OUTER LAYER)
OVER FLASHING AT PENETRATION AND
TRIMMED TO FIT AROUND PENETRATION

44
Edition 1st
Printing
INSULATION
WALL SYSTEM
SHEATHING
(2) LAYERS WRB*
LATH
BED EXTERIOR FLANGE
IN SEALANT
PLASTER RING
MORTAR SETTING BED
STONE VENEER
MORTAR SCRATCH COAT
(2) LAYERS WRB
LATH
INTERIOR EXTERIOR
SECTION VIEW
*SEE FIGURES 29, 30, AND 31 FOR FLASHING OPTIONS.
Figure 32. Penetration, Fixture
Plaster rings should be affixed over the service box to bring the face of the box flush with the adhered manufactured stone
veneer. Bed the exterior flange in sealant. Water resistive barrier should be installed snugly around the plaster ring flange.

45
Edition 1st
Printing
Figure 33. Penetration, Dryer Vent
Bed all covers, flanges, and escutcheons in sealant before fastening to the wall.
INTERIOR EXTERIOR
SECTION VIEW
STONE VENEER
MORTAR SETTING BED
MORTAR SCRATCH COAT
BED EXTERIOR FLANGE
IN SEALANT
EXTERIOR DRYER VENT
LATH
(2) LAYERS WRB*
SHEATHING
WALL SYSTEM
*SEE FIGURES 29, 30, AND 31 FOR FLASHING OPTIONS

46
Edition 1st
Printing
Figure 34. Deck Termination
Lap water resistive barrier over weep screed and floor framing to manage water intrusion. Provide gap between adhered
manufactured stone veneer and decking for drainage. Water management at the deck ledger boards is critical, and may vary
based on the building design.
SHEATHING
LATH
MORTAR SCRATCH COAT
MORTAR SETTTING BED
ADHEREDMANUFACTURED
STONE VENEER
(2) LAYERS WRB
LAP WRB OVER WEEP SCREED
OR FLASHING
FLASHING OR WEEP SCREED
FLOOR FRAMING
LEDGER
DECK FRAMING
STONE VENEER
FLASHING
MORTAR SETTING BED
MORTAR SSCRATCH COAT
(2) LAYERS WRB
LATH
SHEATHING
1IN.(25mm)
MIN.
SECTION VIEW

47
Edition 1st
Printing
A sloping solid shim should top the wall under the flashing and lath. Flashing should lap the top of the wall.
Lath should lap over the top of the wall but be fastened only to vertical wall faces.
Figure 35. Wall Cap
VENEER CAP IN MORTAR SETTING BED
LEVEL SCRATCH COAT AT TOP OF WALL
LATH OVER TOP OF WALL - LAP OVER
WALL LATH 4 IN. (102 mm) MIN. FASTEN
LATH AT VERTICAL WALL FACES ONLY
FLASHING OVER TOP OF WALL
CONSTRUCTION. LAP OVER WRB
SLOPING SOLID SHIM
(e.g. BEVELED SIDING)
MORTAR SETTING BED
MORTAR JOINT (WHERE REQUIRED)
MORTAR SCRATCH COAT
WRB (WHERE REQUIRED)
SHEATHING
WALL SYSTEM
2IN.(51mm)
MIN.
1 IN.
(25 mm)
MIN.
SECTION VIEW

48
Edition 1st
Printing
STONE VENEER
MORTAR SETTING BED
MORTAR SCRATCH COAT
LATH
(1) LAYER WRB OR
MORTAR SCREEN
DRAINAGE MEDIUM
(1) LAYER WRB
SHEATHING
ISOMETRIC VIEW
Figure 36. Wall Assembly – Optional Rainscreen System –
Drainage System
A rainscreen system incorporating a drainage medium (drainage mat or formed polymer sheeting, etc.) on the exterior side
of the primary WRB.

49
Edition 1st
Printing
A rainscreen system of vertical strapping / furring creates a vertical gap between the primary WRB and the mortar screen /
WRB on the back of the scratch coat. *Furring fastened into framing and into nailable sheathing between framing.
STONE VENEER
MORTAR SETTING BED
MORTAR SCRATCH COAT
(1) LAYER WRB OR
MORTAR SCREEN
(1) LAYER WRB
SHEATHING
ISOMETRIC VIEW
PRESSURE TREATED FURRING*
8 IN. (203 mm) O.C.
LATH
Figure 37. Wall Assembly – Optional Rainscreen System –
Strapped

50
Edition 1st
Printing
SHEATHING
WRB
DRAINAGE MEDIUM
MORTAR SCREEN / WRB
LATH
MORTAR SCRATCH COAT
MORTAR SETTING BED
STONE VENEER
FLOOR FRAMING
LAP WRB OVER WEEP
SCREED FLANGE
WEEP SCREED, DRIP SCREED,
OR CASING BEAD (OPTIONAL)
OR WEEP SCREED
EXTEND ADHERED MANUFACTURED
STONE VENEER MIN. 1 IN. (25 mm)
BELOW TOP OF FOUNDATION
2 IN. (51 mm) MIN. AT PAVING
4 IN. (102 mm) MIN. AT GRADE
SLOPE GRADE
2% MIN.
SECTION VIEW
Figure 38. Foundation Wall Base – Optional Rainscreen System
The “Drainage Medium” of this wall section represents rainscreen products (such as drainage mats or formed polymer
sheeting, etc.) or construction techniques (such as strapping or furring).

51
Edition 1st
Printing
Figure 39. Typical Wall Section – Optional Rainscreen System
The “Drainage Medium” of this wall section represents rainscreen products (such as drainage mats or formed polymer
sheeting, etc.) or construction techniques (such as strapping or furring).
WALL SYSTEM
SHEATHING
(2) LAYERS WRB
LATH
MORTAR SCRATCH COAT
MORTAR SETTING BED
STONE VENEER
EXTERIOR
SECTION VIEW

52
Edition 1st
Printing
Figure 40. Retaining Wall (CMU)
Adhered masonry veneer offers attractive aesthetics to retaining walls.
1
SECTION VIEW
APPLIED LIQUID
WATERPROOF COATING
GRAVEL BACKFILL APPROXIMATELY
6 IN. (152 mm) WIDE PROVIDE
DRAINAGE AT FOOTING
LANDSCAPE CLOTH (OPTIONAL)
STONE VENEER CAP IN
MORTAR SETTING BED
1 IN. (25 mm) MIN.
LEVEL SCRATCH COAT AT
TOP OF WALL
STONE VENEER
MORTAR SETTING BED
CMU WALL SYSTEM
WATERPROFFING (WHEN
REQUIRED)
1
GRADE

53
Edition 1st
Printing
Figure 41. Wall—Section Interior Over Cement Backer Board
WOOD FRAMING
MORTAR SETTING BED
CEMENT BACKER BOARD
TO BE INSTALLED PER
MANUFACTURER
STONE VENEER
MORTAR JOINT
(WHERE USED)
INTERIOR EXTERIOR
SECTION VIEW

54
Edition 1st
Printing
Figure 42. Forward Mounted Commercial Window
(2) LAYERS WRB WRAPPED
INTO ROUGH OPENING
SELF ADHERED FLASHING
MEMBRANE
LATH
FIELD FAB CUSTOM
DRIP CAP
INTO ROUGH OPENING
CORNER UNIT
OPTIONAL CASING BEAD
(NOT SHOWN)
BACKER ROD, SEALANT
WINDOW JAMB
BACKER ROD, SEALANT
(NOT SHOWN)
PAN FLASHING
JAMB DETAIL
SECTION VIEW

55
Edition 1st
Printing
Figure 43. Forward Mounted Commercial Window—Top View
(2) LAYERS WRB WRAPPED INTO
ROUGH OPENING
CORNER UNIT
BACKER ROD, SEALANT
WINDOW JAMB
(NOT SHOWN)
NOTE: FOR GUIDANCE WITH LATH FASTENING SYSTEM REFER TO THE FOAM
COALITION WEBSITE, AS WELL AS LATH FASTENER SECTION OF THIS GUIDE. AIR
BARRIER, VAPOR BARRIER, WATER-RESISTIVE BARRIER, WATERPROOFING
MEMBRANE, FLASHING, LATH ATTACHMENT, Z-CHANNEL, AND INSULATION TYPE AND
LOCATIONS TO BE DETERMINED BY DESIGN PROFESSIONAL
SECTION VIEW

56
Edition 1st
Printing
Figure 44. Commercial Storefront Window—Top View
WINDOW JAMB
(2) LAYERS WRB WRAPPED INTO
ROUGH OPENING
TRIM MATERIALS SPECIFIED BY
OTHERS
CASING BEAD OPTIONAL
(NOT SHOWN)
BACKING ROD, SEALANT
SECTION VIEW
MEMBRANE, FLASHING, LATH ATTACHMENT, Z-CHANNEL, AND INSULATION TYPE AND
LOCATIONS TO BE DETERMINED BY DESIGN PROFESSIONAL

57
Edition 1st
Printing
Figure 45. Commercial Storefront Window
INTO ROUGH OPENING
SELF ADHERED FLASHING
MEMBRANE
INTO ROUGH OPENING
(NOT SHOWN)
BACKER ROD, SEALANT
WINDOW JAMB
BACKER ROD, SEALANT
(NOT SHOWN)
PAN FLASHING
JAMB DETAIL
SECTION VIEW
TRIM MATERIALS
SPECIFIED BY OTHERS
DRIP CAP
BEDDING SEAL
TRIM MATERIALS
SPECIFIED BY OTHERS
SLOPPED SILL SPECIFIED
BY OTHERS

58
Edition 1st
Printing
Figure 46. Wall—Section Multi-Floor Joint Detail
SECTION VIEW
NOTE: FOR GUIDANCE WITH LATH FASTENING SYSTEM REFER TO
THE FOAM COALITION WEBSITE, AS WELL AS LATH FASTENER
SECTION OF THIS GUIDE. AIR BARRIER, VAPOR BARRIER,
WATER-RESISTIVE BARRIER, WATERPROOFING MEMBRANE,
FLASHING, LATH ATTACHMENT, Z-CHANNEL, AND INSULATION TYPE
AND LOCATIONS TO BE DETERMINED BY DESIGN PROFESSIONAL
LAP WRB OVER FLASHING
SILL SCREED FLANGE
WEEP SCREED, DRIP
SCREED, OR WEEP
BEDDING SEAL UNDER
SIZED PER THICKEST STONE
FLASHING
SHEATHING
MORTAR SCRATCH COAT
MORTAR SETTING BED
STONE VENEER
SEE DETAIL ABOVE
(2) LAYERS WRB
MORTAR JOINT
(WHERE USED)
LATH
WALL SYSTEM
1IN.(25mm)MIN.
DETAIL
WRB

59
Edition 1st
Printing
Figure 47. Wall—Section Over Rigid Insulation with Additional
Sheathing
SECTION VIEW
NOTE: FOR GUIDANCE WITH LATH FASTENING SYSTEM REFER TO THE FOAM COALITION
WEBSITE, AS WELL AS LATH FASTENER SECTION OF THIS GUIDE. AIR BARRIER, VAPOR
BARRIER, WATER-RESISTIVE BARRIER, WATERPROOFING MEMBRANE, FLASHING, LATH
ATTACHMENT, Z-CHANNEL, AND INSULATION TYPE AND LOCATIONS TO BE DETERMINED
BY DESIGN PROFESSIONAL
WALL SYSTEM
SHEATHING
(2) LAYERS WRB - IF EVALUATED
AS SUCH, FOAM MAY QUALIFY
AS ONE LAYER OF WRB
LATH
MORTAR SCRATCH COAT
MORTAR SETTING BED
CONTINUOUS INSULATION
STONE VENEER
LATH FASTENER
MORTAR JOINT (WHERE
USED)
EXTERIORINTERIOR

60
Edition 1st
Printing
Figure 48. Wall—Section Over Continuous Rigid Insulation CMU
SECTION VIEW
LATH
EXTERIORINTERIOR
MASONRY WALL SYSTEM
(CMU SHOWN)
MORTAR SCRATCH COAT
MORTAR SETTING BED
STONE VENEER
LATH FASTENER EVERY 6 IN.
(152 mm) AS PER SECTION
7.10.5 PER ASTM C1063
WRB (OPTIONAL)

61
Edition 1st
Printing
Figure 49. Wall-Section Inside Corner with Stucco—Top View
EXTEND AT LEAST ONE LAYER OF
WRB FROM EACH DIRECTION
AROUND CORNER 12 IN. (3O5 mm)
MIN.
LATH - WRAP LATH AROUND
CORNER TO NEXT FRAMING
MEMBER
STUCCO
STONE VENEER
MORTAR SCRATCH COAT
MORTAR SETTING BED
LAP LATH AT FRAMING MEMBER
(2) LAYERS WRB
SHEATHING
PLAN VIEW

62
Edition 1st
Printing
Figure 50. Wall-Section Insulated Concrete Form (ICF)—Top
View
SECTION VIEW
MEMBRANE, FLASHING, LATH ATTACHMENT, Z-CHANNEL, AND INSULATION TYPE
AND LOCATIONS TO BE DETERMINED BY DESIGN PROFESSIONAL
ICF PLASTIC REINFORCEMENT
TIES (TYPICAL)
STONE VENEER
LATH FASTENER
MORTAR SETTING BED
WATERPROOFING
MEMBRANE (OPTIONAL)
MORTAR SCRATCH COAT
(2) LAYERS WRB (IF NEEDED)
IF EVALUATED AS SUCH,
FOAM MAY QUALIFY AS ONE
LAYER OF WRB
INSULATED CONCRETE FORM
(BOTH SIDES)
CONCRETE CORE
LATH

63
Edition 1st
Printing
Figure 51. Wall-Section Over Continuous Rigid Insulation with
Z Channels—Top View
SECTION VIEW
EXTERIORINTERIOR
WALL SYSTEM
AS ONE LAYER OF WRB
LATH
MORTAR SCRATCH COAT
MORTAR SETTING BED
STONE VENEER
Z CHANNEL
MORTAR JOINT
(WHERE USED)

64
Edition 1st
Printing
Figure 52. Wall-Section Over Continuous Rigid Insulation
SECTION VIEW
EXTERIORINTERIOR
AS ONE LAYER OF WRB
LATH
MORTAR SCRATCH COAT
MORTAR SETTING BED
STONE VENEER
MORTAR JOINT
(WHERE USED)
WOOD FRAMING
SHEATHING
LATH FASTENER - SEE LATH
FASTENER SECTION

65
Edition 1st
Printing
Figure 53. Wall-Section Parapet with Stone Cap
SECTION VIEW
1X FILLER - SLOPE TOP
ROOF UNDERLAYMENT -
(2) LAYERS WRB
STONE VENEER
MORTAR JOINT (WHERE
USED)
MORTAR SETTING BED
LATH
SCRATCH COAT
BACKER ROD & SEALANT
SLOPING SOLID SHIM (e.g.
BEVELED SIDING)
FLASHING OVER TOP OF
WALL CONSTRUCTION.
LAP OVER WRB
LEVEL SCRATCH COAT AT
TOP OF WALL
LATH OVER TOP OF WALL -
LAP OVER WALL LATH
4 IN. (102 mm) MIN. FASTEN
LATH AT VERTICAL WALL
FACES ONLY
STONE VENEER CAP IN
MORTAR SETTING BED
SHEATHING
SCUPPER
CURF
1IN. (25 mm) MIN.

66
Edition 1st
Printing
Figure 54. Wall-Section Parapet with Steel Cap
LATH
SCRATCH COAT
SHEATHING
1 IN.
(25 mm)
PERARCH.
STYLE
SECTION VIEW
(2) LAYERS WRB
PRESSURE TREATED
BLOCKING
SLOPED METAL COPING SYSTEM
DRIP EDGE PER
ARCH.
MEMBRANE FLASHING
EXTEND OVER TOP
OF PARAPET
STONE VENEER
SCUPPER
MORTAR JOINT (WHERE
USED)
SEALANT, TYPICAL
ROOF SYSTEM
PER ARCH.
MORTAR SETTING BED

67
Edition 1st
Printing
Notes:

Installation Guide and Detailing Options for Compliance with ASTM C1780

Installation Guide and Detailing Options for Compliance with ASTM C1780

More Related Content

What's hot (20)

Viewers also liked (20)

More from Tri County Exteriors LLC (19)

Recently uploaded (20)

Installation Guide and Detailing Options for Compliance with ASTM C1780