IRJET- A Review on Dynamic Analysis of RCC Building Considering Soil Structure Interaction

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 06 Issue: 07 | July 2019 www.irjet.net p-ISSN: 2395-0072
© 2019, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 2799
A Review on Dynamic Analysis of RCC Building Considering Soil
Structure Interaction
Purva M. Kulkarni1, Dr. Y.M. Ghugal
1PG Student, Government College of Engineering, Karad
2Head of Department, Applied Mechanics, Government College of Engineering, Karad
----------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - During earthquakes seismic waves propagate
from the bedrock through the soil layers and damage
structures on the surface. In this present era of rapid growth
and urbanization along with the scarcity of land area one is
forced to build the structures even on the relatively soft soil
which were considered unsuitable for constructing purpose
in the past. However it is possible to construct the structure
because of the advancement in variousgroundimprovement
techniques. Seismic behavior of structure that is built on soft
soils is mainly influenced by the soil properties, and the
structural response is considerably different from the fixed-
base condition beholding to the interaction between the
structures and the ground. Effect of the primitive soil on the
seismic response of structures can be ignored when the
ground has a stiff stratum, and subsequently the structure
can be considered as a fixed-base condition. Analytic and
numerical models for dynamic analysis typically ignoredSSI
effects of the coupled in nature structure-foundation-soil
system. It has been recognized that SSI effects may have a
significant impact for heavier structures and soft soil
conditions. This paper presents an overview of literature
related to the effect of soil structure interaction. The review
includes literature based on software analysis and
experimental results.
Key Words: Soil Structure interaction, Winkler’s
approach, Piled Raft foundation, SAP2000
1. INTRODUCTION
Structures founded on the rock are considered as fixed
base structures. When a structure is formed on solid rock
is subjected to an earthquake, the extremely high stiffness
of the rock constrain the rock motion tobeveryclosetothe
free field movement and can be considered as a free field
movement and fixed base structures. Dynamic analysis of
SSI can be done using Direct Method and Substructure
Method. The direct approach is one in which the soil and
structure are modeled together in a single step accounting
for both inertial and kinematic interaction. Substructure
method is one in which the analysis is broken down in
several steps that is the principal of superposition used to
isolate the two primary causes of SSI (Wolf, 1985). If the
structure is supported on soft soil deposit, the lack of the
foundation to adapt to the deformations of the free field
motion would cause the motion of the structure to deviate
from the free field motion, additionally the dynamic
response of the structure itself can induce deformation of
the supporting soil. This process, in which the response of
the soil influences the motion of the structure and the
response of the structure influences the motion of the soil,
is studied under the interaction effects and popularly
known as soil structure interaction. These effectsaremore
significant for stiff and heavy structures supported on
relatively soft soils. For soft and light structures
established on stiff soil these effects are generally small.
2. LITERATURE REVIEW
2.1 Software based analysis
Nguyen et al [1] investigated the soil structure interaction
phenomena on a 15-story moment-resisting frame sitting
on differently sized end-bearing and floating pile
foundations. A three-dimensional (3D) numerical model is
analyzed for the nonlinear behavior ofthesoil medium,the
piles, and the structural elements. Results show that the
kind and size of the pile parts influence the dynamic
characteristics and unstable response of the building due
to interaction between the soil, pile foundations, and the
structure. A nonlinear time historydynamicanalysisunder
the influence of the earthquake ground motions, including
the 1994Northridge and 1940 El Centro earthquakes, was
performed. SAP2000v14 software was used for the
structural analysis and design of the cross sections of
beams and columns.
Mathew et al [2] analyzed a nine storey RC building
asymmetric in plan, located in seismic zone III using
SAP2000. Pushover analysis has been performed to obtain
effect of soil-structure interaction on buildings resting on
different types of non-cohesive soil, viz., soft and rock. The
properties assigned for these two soil classes are specified
by ATC 40.Comparison was made between fixed base
without considering soil structureinteraction,flexiblebase
by considering SSI in hard soil condition, and flexible base
by considering SSI in soft soil condition. The stiffness of
springs has been estimated using Richart and Lysmer
model. The values of displacements for different types of
soil have been compared.
Bagheri et al [3] investigated theeffectofsoil-pilestructure
interaction on seismic response of structures. Numerical
simulations on two types of superstructures and six types
of piled raft foundations were carried using finite element
software SAP2000. Parametric study was conducted using

time histories of various earthquakes. Two 15 and 30
storey buildings were selected with total heights of 45 and
90 m, respectively. In this research, the Mohr-Coulomb
model was used to simulate the soil nonlinear behavior.
The working mechanism of the composite piled raft
foundation was carried considering a long pile
arrangement with a short pile interval. 2D and 3D models
were compared on the basis of lateral displacements.
Maheshwari and Rajib [4] developed a MATLAB to model
three-dimensional soil-pile-structure systems. A 2 × 2 pile
group in liquefiable soil was considered and a parametric
study was conducted to investigate its seismic behavior.
The effects of loading intensity and stiffness of the soil on
the seismic behavior of the soil-pile system were
investigated. Three conditions of soil behavior were
considered such as linear elastic, soil without pore
pressure generation capacity and soil without pore
pressure generation capacity. Effects of stiffness, soil
nonlinearity, amplitude of acceleration and pore pressure
were studied.
Juirnarongrit and Ashord [5] used the p–y method for
analysis of single piles and pile groups subjected to lateral
spreading. The piles in the groups were modeled as an
equivalent single pile with four times the flexural stiffness
of a single pile for the four-pile group and nine times the
flexural stiffness of a single pile for the nine-pile group.
Winkler spring model was used to determine responses of
the single piles by imposing the known free-field soil
movement profile. For liquefied soils, zero spring stiffness
was used and for non-liquefied soils,soil springsused were
based on standard p–y springs. Curves were plotted of pile
head displacement and maximum moment versus ground
surface displacement for single pile considering linear and
non-linear pile behavior. For piles in group, depth-
displacement, depth-rotation and depth-moment curves
were plotted.
Yang and Liang [6] derived solution to numerically solve
the problem of laterally loaded piles in layered soils using
beam on an elastic foundation model. Mathematica
software was used to derive numerical solution.Stiffnessof
soil varied linearly along the length of pile. The soil profile
consisted of two layers. Four different possible
combinations of this profile were considered in this study.
The numerical solution was validated against an existing
solution for linearly varying soil stiffness in a single soil
layer system and an existing solution for a two-layer soil
system with constant soil stiffness. The results were
compared with free and fixed head existing solutions.
Kim and Rosset [7] analyzed structures with a constant
base and variable height. Response spectra for a single
degree of freedom SDOF system simulating a buildingwith
a mat foundation on soft soil, with and without piles, were
obtained considering the soil–structure system. The depth
of the soil layer (H) was 30 m. horizontal and rocking
stiffness were compared for linearandnon-linear behavior
of soil for mat foundation. Also, elastic and inelastic
response spectra of SDOF system and that of soil were
compared for mat foundation.
Haldar and Babu [8] examinedpile failuremechanismsviz.,
bending, buckling, shear failure,andsettlementfailure.The
finite difference program, FLAC was used to obtain thepile
response. Response of a single end bearing pile in a
liquefiable soil for different soil, pile, and earthquake
parameters is analyzed using time history method.
Concrete piles and steel tube piles with two different pile
diameters were used. Shear strain-frequency, amplitude-
frequency and depth-frequency curves were plotted.
Maheshwari et al [9] analyzed single piles and pile groups
considering the effects of kinematic and inertial
interaction. The harmonic seismic excitation is applied at
the base of the bedrock for the single pile model, and the
response was calculated at the pile head and at the top of
the structure. The analysis was performed for excitation
with different frequencies.
Ghandil and Behnamfar [10] studied the direct method of
soil–structure interaction analysis. Dynamic non-linear
time history analysis was implemented using earthquake
records structural responses were compared for different
assumptions of soil behavior including the elasto-plastic,
Mohr–Coulomb, equivalent linear and the proposed
modified equivalent linear method. Six 3D steel buildings
with 5, 10, 15, 20, 25, and 30 stories were considered.
Buildings were modeled in SAP2000 software. Maximum
lateral displacements of stories with and without SSI were
plotted fox all six buildings. Also, maximum storey shear
with and without SSI were plotted.
Luo et al [11] compared an equivalent linear model
developed from the ground response analysis and the
modified Drucker–Prager model. Analysis was done on
three types of soils viz., silty clay, sandyclayandrock.Time
history method was used. Maximum lateral displacement
curves were plotted for model with and without soil
structure interaction. Maximum lateral deflections resting
on model with equivalent linear soil and non-linear soil
were plotted.
Ghandil and Behnamfar [12] analyzed short to tall
buildings including 5, 10, 15 and 30 story structures. A
number of consistent earthquakes were applied on two
existing soft soils. Profile I consists of a singlesandlayer25
m thick, on the bedrock. Profile II includes three layers of
clay, totally 45 m thick, on the bedrock. Storey drifts and
storey shears were plotted with storey height considering
SSI and without SSI.
Sica et al [13] conducted parametric study of a vertical
cylindrical pile embedded in a two-layer soil profile to
vertically-propagating S waves. The analyses were

performed using a mixed numerical-analytical beam-on-
dynamic-Winkler-foundation (BDWF) model. The soil
profile consisted of a soft surface soil layer lyingona stiffer
stratum. Elastic bedrock conditions have been assumed at
the bottom of the lower layer. Shear strain, stiffness and
damping vs. depth curves and interface kinematic bending
moment vs. frequency curves were studied.
Mucciacciaro and Sica [14] analyzed single pile embedded
in a soil deposit made of two cohesive layers of huge
stiffness contrast between the consecutive soil layers in
order to represent the worst conditions in terms of
kinematic pile bending at the soil layer interface. Analysis
was carried usingfinite elementcodeABAQUS. Shearstress
and bending moments were plotted with respect to depth
of soil.
Matinmanesh and Asheghabadi [15] carried the soil-
structure interaction analysis using AbaqusV.6.8program.
Two buildings with 5 and 20 storey, one-bay moment
resistant frames representing low and high rise buildings
were used to investigate the effect of structure height on
response of the soil-structure system. Analysis was
performed using low, intermediate and high magnitude
earthquakes. Influence of different sub-soils (dense and
loose sand), buildings height on earthquakeresponse were
investigated. Maximum acceleration and maximum
principal stresses were plotted.
Abbasa et al [16] studied the influence of vertical and
lateral loads on pile group. The analysis was done using
finite element method and p-y analysis. Effect of load
combinations on pile group was performed on three pile
group configurations. Lateral displacements of single pile
and that of group of piles was compared and it was
concluded that group interaction effect led to reduced
lateral resistance for the pile in the group compared tothat
for the single pile.
Mohti and Khodair [17] investigated pile-soil interaction
due to application of axial and lateral loads to piles in sand.
3-D finite element models were created using Abaqus/Cae
and SAP2000. The steel H-piles were used to support the
abutment of integral bridges. Various types of soft soils
were studied such as loose, medium, and dense sand.
Nonlinear soil springs were assigned at different depth
locations along the pile length. Bending moments and
lateral displacements along the depth of the pile were
obtained from FE analyses.
Badry and Satyam [18] analyzed asymmetric L-shaped 11
storey building resting on pile foundation with soil
structure interaction effect. Applicabilityofequivalentpier
method was studied. The parametric studywascarriedout
for different input of earthquakes and soil types. Four
different trial configurations for equivalent piers were
considered. Lateral displacements atdifferentdepths were
plotted with respect to time. It was found that, the EPM
model which makes the SSI model computationally more
efficient shows the same variation in responses as
observed in the general pile layout model.
Chore and Sawant [19] carried numerical modeling of
space frame-pile foundation system using finite element
models. Parametric study was done using sub-structure
approach. The soil used for analysis was cohesionless soil.
Two different pile groups comprising two and three piles
each in a group with series and parallel arrangement of
piles were considered. Displacements and bending
moments were compared with that of fixed base model.
Also the effect of L/D ratio on displacements was found.
Jegatheeswaran and Muthukkumaran [20] studied the
behavior of pile foundation due to combined vertical and
horizontal loads in homogenous layer of sandy soil. Also,
analysis of pile foundation on sloped ground was done by
varying slope angles. Behavior of pile due to lateral soil
movement was studied. Influence of lateral load as well as
combined load on displacement at pile head at both
horizontal and sloped grounds was plotted. Also,
settlement of a pile on both horizontal and sloped grounds
was plotted.
Jesmani et al [21] performed three dimensional finite
element analyses to study the buckling behavior of fully
and partially embedded concrete piles. Loose,mediumand
dense sandy soil was used for analysis and only axial load
was applied. Static vertical load was applied and increased
till buckling of pile occurs. Results of the numerical model
have been verified by previous experimental results.
Critical buckling load vs. normalize length of pile was
plotted for fully and partially embedded piles for three
types of sandy soil considered.
Khodair and Mohti [22] analyzed pile- soil interaction
numerically underaxial andlateral loads usingAbaqus/Cae
and SAP2000. Two three dimensional, finite element (FE)
models of steel piles for bridge embedded in clay were
analyzed. The soil profile consisted of three layers; two
layers of stiff clay without free water and onelayerofweak
rock. The effect of varying the number of soil springs (7, 9,
12) on the induced bending moment and lateral
displacement along the depth of the pile was examined
from the FD solutions and FE. The results from SAP2000
were compared to those from FD solution by LPILE due to
the effect of an induced displacement of 2 cm at the top of
the pile.
Lee and Moon [23] developed a computer program
incorporating an approximate hybrid analysis method for
the practical design of piled raft foundations. In the
presented method of analysis, the interactions between
pile-soil, raft-soil, pile-soil-pile and raft-soil-pile were
considered, and the effect of nonlinear behavior of piles
and the interactions between piled raft components and
soil were investigated by comparing with 3-dimensional

FEM program analysis results. It was foundthatthepilesin
a piled raft foundation reduce the total settlement as well
as increases the total bearing capacity, it is very important
to estimate accurately the nonlinear behavior of piles after
yielding for the economic design of piled raft foundation.
Fayun et al [24] solved the equations of axially loadedpiles
subjected to lateral soil movement based on the flexural
differential equations of elastic piles and Winkler’s spring
model of pile-soil interaction.Finitedifferencemethodwas
used to solve the flexural differential equations. Shielding
effect between piles was analyzed using Mindlin’s method.
A parametric study was conducted to examine the
influence of pile spacing, number, location and the
magnitude of axial load.
Jinyuan et al [25] studied the finite element analyses of
negative skin friction on a single pile under various
conditions. Finite element program, ABAQUS was used to
develop 2-D axisymmetric model. Parametric analysiswas
performed to investigate the influence of negative skin
friction along the pile length of various influencing factors,
including the consolidation time, thepropertiesofpile/soil
interface, the lateral earth pressure coefficient, pile-soil
limiting displacement, the intensity of surcharge, and soil
stiffness. A simple design procedure was proposed for
estimating the pile load caused by negative skin friction
based on the field measurements from literature and this
investigation.
2.2 Experimental studies
Kim et al [26] analyzed effect of negative skin friction on
single piles by one-dimensional consolidation model test.
Computer program pile negative skin friction (PileNSF)
was developed to calculate bearing capacity of pile
embedded in a consolidating ground due to surcharge
loading. Laboratory model test was performed to
investigate the development of negative skin friction on
single piles, as well as to validate the computer program
(PileNSF). The values of soil settlement, excess pore water
pressure, and axial force on pile were found and compared
between the two methods adopted.Variousmodelsofpiles
with stratified soils were analyzed in PileNSF considering
negative skin friction. Effects of consolidation, axial load,
pile diameter, bearing layer were found with respect to
depth of embedment.
Hokmabadi et al [27] considered 5-storey, 10-storey and
15-storey model structures and conducted shake table
tests on these structures. Also a 3 dimensional numerical
model was designed to compare the results with shake
table tests. Influence of Northridge, Kobe, El Centro, and
Hachinohe earthquakes was studied on each model by
considering effect of soil structure interaction and without
considering effect of soil structure interaction. Lateral
deflections, bending moments and inter storey drifts were
compared at each storey levels.
Suleiman et al [28] experimentally investigated the soil-
structure interaction of piles used to stabilizefailingslopes
by applying lateral load to piles. Displacement and tilt
gauges at the pile head and strain gauges, a flexible shape
acceleration array, and thin tactile pressure sheets along
the pile length were used. The soil used in the experiment
was classified as well-graded sand. The lateral load was
applied on the top soil and the displacements measured at
three locations- at top soil box, the displacement ofthepile
at the soil surface and the displacement of the pile at the
sliding surface. Applied load versus lateral displacement
graphs were plotted.
Lin et al [29] conducted the experiment to investigate the
soil-structure interaction of single short, stiff laterally
loaded hollow steel pipe pile. Sensors clinged to the pile
were used to develop the compressive soil-pile interaction
pressures and also the lateral displacement along the pile
length. Using these measures, force-displacement curve
and depth strain curve were plotted. The resultsofthistest
were compared with results of testsconducted bydifferent
methods and data in literature.
Ashour et al [30] evaluated behavior of a long flexible pile
group in uniform and layered soil. Strain wedgemodel was
developed to analyze pile groupunderlateral loading.Load
test was carried on pile group and single pile in layered
clay, sand, layered sand and clay soil, in loose and medium
dense sand. The lateral response of individual pile and pile
group were assessed by plotting load-deflection curve.
Hussien et al [31] conducted shake table tests to examine
the dynamic responses of single and grouped end bearing
piles in dense sand. The model was prepared in a strong
container. Distributionsofnormalizedsteadystatebending
moments of piles in a group for free head piles, group piles
supporting SDOF structure and group piles supporting
2DOF structure were plotted w.r.t. depth.
Ghayoomi et al [32] studied the behaviorof pilefoundation
supported single degree of freedom structures in dry and
unsaturated fine sands. Centrifuge tests were carried to
study the behavior of structure. Two types of sands of
different degree of saturation were considered. The time
history of Northridge earthquake was used as input
motion. Seismic responses in terms of acceleration, lateral
displacement, and frequency content were plotted. The
lateral deformation profiles of the systems both in far field
and piles showed lower deformations for unsaturatedsoil-
pile systems due to higher stiffness of unsaturated sand.
3. CONCLUSIONS
The review of soil- structure interaction leads tofollowing
conclusions:
1. The effect of interaction should be considered for
accurate calculation of design forces.

2. Soil-structure interaction may cause increase in
seismic base shear, time periodofbuildingframes.
This effect is seen mostly in soft soils than hard
soils having higher stiffness.
3. The soil mass is considered as homogenous,
isotropic and behaving in linear and nonlinear
manner in the interaction analysis.
4. Roof displacement, storey displacement is also
observed to be increasing due to incorporation of
SSI.
5. Compared to Winkler’s approach (Spring Model)
the Natural Period,RoofDisplacement,BaseShear,
Beam Moment and Column Moment are observed
to be increasing more in case of Elastic continuum
approach (FEM model).
6. At least Winkler’s method should be employed to
consider SSI instead of fixed base condition for
practical purpose.
7. Parametric studies consisting of pile spacing,
number, and location and magnitude of axial load
are conducted to investigate the influence of soil-
structure interaction.
REFERENCES
1. Nguyen Q. V., Fatahi B. and Hokmabadi A. S., “Influence
of Size and Load-Bearing Mechanism of Piles on
Seismic Performance of Buildings Considering Soil–
Pile–Structure Interaction”, International Journal of
Geomechanics, American Society of Civil Engineers, Vol
17, No. 7, 04017007:1-22, 2017.
2. Mathew, Cinitha, Umesha, Iyer and Sakaria, “Seismic
response of RC building by considering soil structure
interaction”, International Journal of Structural & Civil
Engineering, Vol. 3, No. 1, February 2014.
3. Mohsen B., Mehdi E. J., Samali B., “Effect of Seismic
Soil–Pile–Structure Interaction on Mid and High-Rise
Steel Buildings Resting on a Group of Pile
Foundations”, International Journal of Geomechanics,
American Society of Civil Engineers, Vol. 18, No. 9,
04018103: 1-27, 2018.
4. Maheshwari B.K., Rajib S., “Seismic Behavior of Soil-
Pile-Structure Interaction in Liquefiable Soils:
Parametric Study”, American Society of Civil Engineers
Vol. 11, No. 4, pp.335–347, 2011.
5. Juirnarongrit T., Ashford S. A., “Soil-Pile Response to
Blast-Induced Lateral Spreading. II: Analysis and
Assessment of the p–yMethod”,JournalofGeotechnical
and Geoenvironmental Engineering, Vol. 132, No. 2,
February 1, 2006, pp.163–172.
6. Yang K., Liang R., “Numerical Solution for Laterally
Loaded Piles in a Two-Layer Soil Profile”, Journal of
Geotechnical and Geoenvironmental Engineering, Vol.
132, No. 11, pp.1436–1443, 2006.
7. Kim Y. S., Roesset J. M., “Effect of Nonlinear Soil
Behavior on Inelastic SeismicResponseofa Structure”,
International Journal of Geomechanics, Vol. 4, No. 2,
June 1, pp.104–114, 2004.
8. Haldar S., G. L. Sivakumar Babu, “Failure Mechanisms
of Pile Foundations in Liquefiable Soil:Parametric
Study”, International Journal of Geomechanics, Vol. 10,
No. 2, pp.74–84, 2010.
9. Maheshwari B. K., TrumanK. Z., M. H. El Naggar, Gould
P.L., “Three-dimensional nonlinearanalysisforseismic
soil–pile-structure interaction”, Soil Dynamics and
Earthquake Engineering, Vol. 24, No. 11, pp.343–356,
2004.
10. Ghandil M., Behnamfar F., “The near-field method for
dynamic analysis of structures on soft soils including
inelastic soil–structure interaction”, SoilDynamicsand
Earthquake Engineering, Vol. 75, no. 4, pp.1–17, 2015.
11. Luo C., Yang X., Zhan C., Jin X., Ding Z., “Nonlinear3D
finite element analysis of soil–pile–structure
interaction system subjected to horizontal earthquake
excitation”, Soil DynamicsandEarthquakeEngineering,
Vol. 84, No. 2, pp.145–156, 2016.
12. Ghandil M., Behnamfar F., “Ductility demands of MRF
structures on soft soils considering soil-structure
interaction”, Soil Dynamics and Earthquake
Engineering, Vol. 92, No. 8, pp.203–214, 2017.
13. Sica S., Mylonakis G., Simonelli A. L., “Strain effects on
kinematic pile bending in layered soil”, Soil Dynamics
and Earthquake Engineering, Vol. 49, No. 3, pp.231-
242, 2013.
14. Mucciacciaro M., Sica S. “Nonlinear soil and pile
behavior on kinematic bending response of flexible
Piles”, Soil Dynamics and Earthquake Engineering, Vol.
107, No. 1, pp.195–213, 2018.
15. Matinmanesh H., Asheghabadi M. S., “Seismic Analysis
on Soil-Structure Interaction of Buildings over Sandy
Soil”, Procedia Engineering, Vol. 14, No. 7, pp.1737-
1743, 2011.
16. Abbasa J. M., Chik Z., Mohd Raihan Taha, “Influence of
axial load on the lateral pile groups response in
cohesionless and cohesive soil”, Frontiers of Structural
and Civil Engineering, Vol. 9, No. 2, pp.176-193, 2015.
17. Mohti A., Khodair Y.,” Analytical investigation of pile–
soil interaction in sand under axial and lateral loads”,

International Journal of Advanced Structural
Engineering, Vol. 54, No. 4, 2014.
18. Badry P., Satyam N.,” An efficient approach for
assessing the seismic soil structure interaction effect
for the asymmetrical pile group”, Innovations in
Infrastructural Solutions, Vol. 8, No. 1, 2016.
19. Chore H. S., Sawant V. A., “Soil-Structure Interaction of
Space Frame Supported on PileFoundationEmbedded
in Cohesionless Soil”, Indian Geotechnical Journal , Vol.
46, No. 4, pp.415-424, 2016.
20. Jegatheeswaran B., Muthukkumaran K., “Behavior of
pile due to combined loading with lateral soil
movement”, International Journal of Geo Engineering,
Vol. 7, No. 8, 2016.
21. Jesmani M., Nabavi S. H., Kamalzare M., “Numerical
Analysis of Buckling Behavior of Concrete Piles Under
Axial Load Embedded in Sand”, Arab Journal ofSciEng,
Vol. 39, No. 2, pp. 2683-2693, 2014.
22. Khodair Y., Mohti A. A.,“Numerical AnalysisofPile–Soil
Interaction under Axial and Lateral Loads”,
International Journal of Concrete Structures and
Materials Vol.8, No.3, pp.239-249, 2014.
23. Lee S. and J. S. Moon, “Effect of Interactions between
Piled Raft Components and Soil on behavior of Piled
Raft Foundation”, Korean SocietyofCivilEngineers, Vol.
22, No. 1, pp.243-252, 2016.
24. Fayun L., Feng Y., and Jie H., “A Simplified Analytical
Method for Response of an Axially Loaded Pile Group
Subjected to Lateral Soil Movement”, Korean Societyof
Civil Engineers, Vol. 17, No. 2, pp.368-376, 2013.
25. Jinyuan L., Hongmei G., Hanlong L., “Finite element
analyses of negative skin friction on a single pile”, Acta
Geotechnica, Vol. 7, No. 3, pp.239–252, 2012.
26. Kim, Mission, Park, Dinoy, “Analysis of Negative Skin-
Friction on Single Piles by One-Dimensional
Consolidation Model Test”, International Journal of
Civil Engineering, Vol. 16, No. 4, pp. 1445-1461, 2018.
27. Hokmabadi A. S., Fatahi B., and Samali B., “Physical
Modeling of Seismic Soil-Pile-Structure Interactionfor
Buildings on Soft Soils”, Internationl Journal of
Geomechanics, Vol. 15, No. 2, 04014046:1-18, 2015.
28. Suleiman M. T., Ni L., Helm J. D., Raich A., “Soil-Pile
Interaction for a Small Diameter Pile Embedded in
Granular Soil Subjected to Passive Loading”, Journal of
Geotechnical and Geoenvironmental Engineering, Vol.
140, No. 5, 04014002:1-15, 2014.
29. Lin H., Ni L., Suleiman M. T., Raich A., “Interaction
between Laterally Loaded Pile and Surrounding Soil”,
Journal of Geotechnical and Geoenvironmental
Engineering, Vol. 141, No. 4, 04014119:1-11, 2015.
30. Ashour M, Pilling P., Norris G., “Lateral BehaviorofPile
Groups in Layered Soils”, Journal of Geotechnical and
Geoenvironmental Engineering, Vol.130,No.6,pp.580-
592, 2004.
31. Hussien M. N., Tobita T., Iai S., Karray M., “Soil-pile-
structure kinematic and inertial interaction observed
in geotechnical centrifuge experiments”, SoilDynamics
and Earthquake Engineering, Vol. 89, No. 8, pp.75–84,
2016.
32. Ghayoomi M., Ghadirianniarin S., Khosravi A.,
Mirshekari M.,” Seismic behavior of pile-supported
systems in sand”, Soil Dynamics and Earthquake
Engineering, Vol. 112, No. 5, pp.162–173, 2018.

IRJET- A Review on Dynamic Analysis of RCC Building Considering Soil Structure Interaction

More Related Content

What's hot (20)

Similar to IRJET- A Review on Dynamic Analysis of RCC Building Considering Soil Structure Interaction (20)

More from IRJET Journal (20)

Recently uploaded (20)

IRJET- A Review on Dynamic Analysis of RCC Building Considering Soil Structure Interaction