IRJET- Development of Redundant Communication Methods for Robots in Nuclear Applications

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 05 Issue: 03 | Mar-2018 www.irjet.net p-ISSN: 2395-0072
© 2018, IRJET | Impact Factor value: 6.171 | ISO 9001:2008 Certified Journal | Page 3063
DEVELOPMENT OF REDUNDANT COMMUNICATION METHODS FOR
ROBOTS IN NUCLEAR APPLICATIONS
S.P.RESHMA1, SAJI JACOB GEORGE2, S.KALPANA3
1B.Tech Student, Electronics and Communication Engineering, Dhanalakshmi Srinivasan college of engineering
and technology, Chennai, India,
2 Scientific Officers, RHIDS/RIMMD, IGCAR, Kalpakkam, India,
3Assitant professor, electronics and communication engineering, Dhanalakshmi Srinivasan college of engineering
and technology, Chennai, India.
---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - Generally the parallel communication between
master control system and its sub-modules like analog front
end, data acquisition unit or final control elementswillrequire
a large number of wires. This project minimizes the cables by
serializing the independent digital and analog lines, thus
providing a better noise immunity to the system. To improve
the data security, data encryption/decryption methods are
used. For redundancy, alternate communication methods are
implemented, thus ensuring flawless data transferevenincase
of failure of one communication stream. Power line
communication and optical fiber communicationmethodsare
complementing each other along withRS-485communication,
providing a secure and redundant data transfer between the
sub-modules in a control system.
Key Words: Serial communication, RS 485, optical fiber
communication, power line communication, printed
circuit board, Arduino board
Introduction:
The data communication is necessary partoftransmissionof
value from control room to robots in the nuclear field. To
make the robot work more efficiently with reduced number
of cables, we introduce this redundant technique for
communication.
Redundant techniques in communication will generally
involve more methods of data transferring. By doing this if
any communication link fails also the alternate method will
help in communication link fails also alternate methods will
help in communication.
This will improve the availability of the robot. Here power
line communication and optical fiber communication
methods are complementing each other along with RS-485
communication, providing a secure and redundant data
transfer between the sub-modules in a control system.
1.1 Communication:
The communication links, across which computers(or parts
of computers) talk to one another, may be either serial or
parallel. A parallel link transmitsone bit of data throughone
channel whereas, a serial link transmits serialized stream of
data will be send through one channel[1]. Hence thenumber
of wire used for communication with the help of serial
communication is less when compared with the parallel
communication.
1.2 Channels for redundancy:
The redundant communication is made possible by
transmitting the data over multiple modes of
communication. Each communication mode can be
considered as a module. In this project we use three
modules:
 RS-485
 Optical fiber communication
 Power line communication
These featuresmake it more important for the channel to be
selected rather than any other channels.
As this project is mainly applied in the nuclear reactor it
should see to that the number of wires used should be
minimum. This is because when the number of wires used
increasesthere isa possibility that the radiationleakagemay
occur.
Hence this idea will reduce the number of wires used for
communication also.
1.2.1. RS-485:
RS-485 is connected with the help of MAX 488 that is more
efficient and provides a full duplex. Hence communication
can occur in both the directions.
Fig:1.circuit connection for RS-485

1.2.2. OPTICAL FIBER COMMUNICATION:
Fiber optic communication is a method of transmitting
information from one place to another by sending pulses of
light through an optical fiber. The light forms an
electromagnetic carrier wave that is modulated to carry
information. By this project we can send pulses of light
through an optical fiber[2,3,4].
Fig:2.circuit connection for optical communication system
1.2.3. POWER LINE COMMUNICATION:
Power line communication (PLC) is the use of existing
electrical cables to transport data, and it has beenaroundfor
a very long time. This basically means any technology that
enables data transfer at narrow or broad band speeds
through power line by using advanced modulation
technology.
This is done with the help of KQ 330F modules. The
advantage of using this module is that allthecomponentsare
widely available, and the range of devices that are available
provide a variety of applications that can be achieved using
simple plug-in or wire-in modules[5,6]
fig:3.circuit connection for power line communication
system
Table -1: merits and demerits of each system
Module RS-485 Optical fiber
communication
Power
Line
communication
Merits: Lower
signal
level
interface
Resistance to
Electromagnetic
Interference
Reduction inthe
number of
wiring used.
Demerits: Not
suitable
to
transfer
large
amount
of data
Cost Is Higher
Than Copper
Cable
Data
attenuation
2. Concept:
In this paper, the multiple communication modules are
established between two micro controllers and a joystick
based motor speed control of robotic arm with stepper
motor as prime mover is implemented to verify the
communication link. The joystick is an analog joystick with
two channels. The data from the joystick is digitized and
send by the transmitter micro-controller (Arduino mega
2560) to the receiving side micro-controller (Arduino mega
2560) using the three communication modules explained in
1.2. The data is displayed in a character LCD in both
transmitting side and the receiving side to verify the data
integrity. The data received in the receiving end
microcontroller is used for controlling the motion of two
stepper motors, in either direction and variable speeds,
according to the position of the joystick lever. The stepper
motors drives the robotic arm through suitable reduction
gears.
A custom shield for MEGA2560 with all required electronics
and connectors is designed and PCB is manufactured. All
three modulesare soldered and tested on thePCB.Programs
for the Arduino boards are written in Arduino IDE.
RS-485
Optical fiber cable
Power line cable
Fig:4. Model of transmission
3. Transmitter side:
In the transmitter side there is a controller (i.e., joystick)
whose values are used to control the robotic arm. It also
consists of the LCD display that helps in displaying the
obtained value. Then the various communication
transmitters are connected to the system in this side.
Trans
mitter
Recei
ver

Fig:5. Circuit connection for transmitter side.
3. Receiver side:
The receiver side will have very similar connection that is in
the transmitter side. The receiver side will have receiving
end connection for each system.
The receiver system will also have the LCD display that will
display the received values from the communication
channel.
In addition to it , the receiver system is connected to the
stepper motor that drives the robotic arm. The stepper
motor is connected and controlled with the stepping drive.
The stepping drive consists of two digital inputs, one for
pulse and the other for direction of rotation. These two
inputs are given to the digital pins of the microprocessor.
Fig:5. Circuit connection for receiver side.
Results & Conclusion:
System has been assembled and tested and communication
was established through all the three channels. The
transmission and reception are done simultaneously and if
any failure occurs in any of the channels, the system will
work efficiently with one communication link. Redundancy
is verified by removing one/two channels in random, the
communication wasfound flawlessand roboticarmistested
successfully.
This project willhelp inprovidingredundantcommunication
with the systems that are far apart. It also reduces the noise
that is present in the system and very useful in
communication system that cannot be regularly verified. It
can be further implemented in automobiles too, so that the
efficiency of the system control is in the hands.
ACKNOWLEDGEMENT
I expressmy sincere thanksto Dr. S Murugan, Head, RIMMD,
FRTG, IGCAR and Mr. C.Rajagopalan, Head, RHIDS, FRTG,
IGCAR for providing the lab faclities at IGCAR and constant
support during the project. I also thank Mr. R. ANANADAN,
HOD ECE, Dhanalakshmi Srinivasan College of engineering
and technology for the continuous support and guidance.
REFERENCES
[1] J.G.Proakis. Digital communications. Mc Graw Hill, 4th
edition, 2001
[2] Yoshitaka Takasaki, member, IEEE, Mitsuo Tanaka,
Narimichi Maeda, member,IEEE,Kiichi Yamashita, and
katsuyuki Nagano,” optical pulse formats for fiber optic
digital communications:”,IEEE TRANSACTIONS ON
COMMUNICATIONS, VOL. COM-24,NO. 4, APRIL 1976
[3] Gred keiser, McGraw Hill, ”optical fiber
communication”,4th edition 2008.
[4] S.D.Personick, J. E. Goell “Receiver designfordigitalfiber
optic communication system, 1-11,” bell syst. Tech .J.,
vol.52,pp.843-886,21.
[5] Zheng-yan Xie;Ming-yue Zhai;Xiao-fengLiu,”researchon
fractal characteristics of broadband power line
communication signal”, International Conference on
wireless communications, Signal processing and
networking, year 2017.
[6] Wong, E.M.C.; , "A phone-based remote controller for
home and office automation," Consumer Electronics,
IEEE Transactions on , vol.40

IRJET- Development of Redundant Communication Methods for Robots in Nuclear Applications

More Related Content

What's hot (19)

Similar to IRJET- Development of Redundant Communication Methods for Robots in Nuclear Applications (20)

More from IRJET Journal (20)

Recently uploaded (20)

IRJET- Development of Redundant Communication Methods for Robots in Nuclear Applications