IRJET- Optimization of Power Flow in Transmission Line using TCSC Controllers

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 06 Issue: 10 | Oct 2019 www.irjet.net p-ISSN: 2395-0072
© 2019, IRJET | Impact Factor value: 7.34 | ISO 9001:2008 Certified Journal | Page 1556
Optimization of Power Flow in Transmission Line using TCSC
Controllers
Prof. Ravindra M. Malkar1, Prof. Vaibhav B. Magdum2
1,2Assistant Professor, Department of Electrical Engineering,
DKTE Society’s Textile & Engineering Institute, Ichalkaranji, (MS), India.
----------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - The power transfer capacity of long high voltage transmission lines is often limited by the inductive reactance of the
transmission line. In some cases, series compensation is used to reduce the inductive reactance of the transmission line, which
increases the power transfer capacity of the transmission line. Numerous methods have been used to provide serialcompensation
of a transmission line. One of these methods is to use a thyristor controlled series capacitor (TCSC). A series controlled thyristor
capacitor (TCSC) belongs to the family of flexible devices for alternating current transmission systems (FACTS). It is a variable
inductive and capacitive reactance device that can be used to provide series compensation on high voltagetransmissionlines. One
of the significant advantages that a TCSC has over other series compensation devices is that the TCSC reactance is instantaneous
and continuously variable. This means that the TCSC can be used not only to provideaseriescompensation, butalsotoimprovethe
stability of the power supply system. The literature has shown that there is an acceptable limit for the resolution of the thyristor
trigger angle based on the parameters of the components used in the TCSC. If a controllerisdevelopedto meetthisacceptablelevel
of thyristor trigger angle resolution, the operation of the TCSC will also be acceptableanditsoperation willnotresultin unwanted
fluctuations in the transmission line variables.
Key Words: FACT Controller, TCSC, SSR, TCR.
1. INTRODUCTION
The Flexible Alternating-Current Transmission Systems (FACTS),incorporatinga widerangeofpossibilitiesfor better
utilization. Improvement of voltage and current limits on the powerelectronicsdevices leadstoa fastdevelopmentofFACTS in
the last decade. FACTS are defined by the IEEE as “AC transmission systems incorporating power electronics-based and other
static controllers to enhance controllability and increase power transfer capability. And among the proposed FACTS devices,
possibly the Thyristor Controlled Series Capacitor (TCSC) has given the best results in terms of performance and flexibility. It
can have various roles in the operation and control of power systems, such as scheduling power flow; decreasing
unsymmetrical components; reducing net loss; providing voltage support; limiting short-circuit currents; mitigating sub-
synchronous resonance (SSR); damping the power oscillation; and enhancing transient stability.[11]
FACTS devices are introduced in the transmission line to enhance its power transfer capability; either in series or in
shunt. The series compensation is an economic method of improving power transmission capability of the lines. Thyrister-
controlled series capacitors (TCSC) is a type of series compensator that can provide many benefits for a power system
including controlling power flow in the line, damping poweroscillations,and mitigatingsubsynchronousresonance.TheTCSC
concept is that it uses an extremely simple main circuit. The capacitor is inserted directly in series with the transmission line
and the thyrister-controlled inductor is mounted directly in parallel with the capacitor. Thus no interfacing voltage
transformers is required. This makes TCSC much more economic than some other competing FACTS technologies. Thus it
makes TCSC simple and easy to understand the operation. Series compensation will:
1) Increase power transmission capability.
2) Improve system stability.
3) Reduce system losses.
4) Improve voltage profile of the lines.
5) Optimize power flow between parallel lines.[3]
Series capacitors offer certain major advantages over shunt capacitors. With series capacitors, the reactive power
increases as the square of line current, whereas with shunt capacitors, the reactive power is proportional to the square of bus
voltage. For achieving same system benefits as those of series capacitors, shunt capacitorsrequiredarethreetosixtimesmore
reactive power rated than series capacitors. Furthermore shunt capacitors typically must be connected at the midpoint,
whereas no such requirement exists for series capacitors. [8]

2. CIRCUIT ANALYSIS OF A TCSC
A single-phase TCSC consists of a fixed-reactance capacitor parallel with a variable reactance inductor. This variable
reactance inductor is obtained by connecting an inductor in series with back-to-back thyristors. For a three phase TCSC this
arrangement is identical for all three phases. The inductor thyristor parallel branch of the circuit is known as a thyristor
controlled reactor. This branch of the circuit is the most important part of a TCSC and therefore requires further discussion
3. THYRISTOR CONTROLLED REACTOR
A thyristor controlled reactor consists of back to back thyristors connected in series with an inductor as shown in
Figure 3.a. The reactance characteristic of the TCR as a function of the trigger angle of the thyristors is shown in Figure 3.b.
Figure 3.a. Circuit diagram of TCR Figure 3.b. Graph of TCR reactance vs. thyristor trigger angle
The characteristic in figure 3.b. shows that the inductivereactanceoftheTCRincreasesasthetriggerangleoftheback
to back thyristors is increased from 00. The equation describing the behaviour of the reactance of the TCR as a function of the
thyristor trigger angle is given by:[1]
XTCR= πXL / 2(π-α) + sin 2α---------------- (1)
Where,
XTCR is the net reactance of the TCR at the fundamental frequency
XL is the reactance of the inductor at the fundamental frequency
α is the trigger angle of the thyristors
The circuit of a TCSC is obtained when a fixed reactancecapacitorisaddedin parallel totheTCR.Byunderstanding the
operation of the TCR it is now possible to analyze the circuit diagram of a single phase TCSC and obtain insight into the
operation and variable reactance characteristic of a TCSC.
4. OPERATION OF THYRISTOR CONTROLLED SERIES CAPACITORS (TCSC)
Figure 4.a. Circuit diagram of thyrister controlled series capacitors TCSC.

Having discussed the circuit diagram and operation of a TCR, its now possible to analyze the circuitdiagramofa TCSC
to understand the operation of a TCSC in greater detail. As shown in Figure 4.a. TCSC consists of two parallel branches one
containing a fixed-reactance capacitor and the other a thyristor controlled reactor (TCR).[1] Using this description and
equation (1), used to describe the operation of a TCR, it is possible to arrive at the following formula used to describe the
operation of a TCSC.
XTCSC=jXTCR//(-jXc)-----------------(2)
So, XTCSC=-jXc/1-Xc/XTCR--------------(3)
Where,
XTCSC is the net reactance of the TCSC at the fundamental frequency
XTCR is the net reactance of the TCR at the fundamental frequency
Xc is the reactance of the TCSC's internal capacitor at the fundamental frequency
Referring to equation (3) it can be seen that as XTCR is decreased the absolute value of XTcsc will be increased. To
illustrate this, two extreme cases will be taken when: XTCR = 00 it can be seen that IXTCSC I = IXC I. The thyristors are not
triggered and the TCR branch is open circuit. This is the condition for minimum series compensation. XTCR ~ Xc itcanbeseen
that IXTcscI= 00. The thyristors are being triggered. This is theconditionofmaximumseriescompensationandisalsothepoint
at which resonance between the inductor and capacitor occurs. However, practically this condition is never realised, for
reasons that are explained later on in this section. The corresponding thyristor trigger angle at which resonance occurs is
defined as α res.
From the previous discussion it was shown that the minimum reactance of the TCSC is equal to the reactance of the
fixed capacitor, therefore the TCSC can be thought of as an 'amplifier' that can, theoretically,boostthereactanceofthephysical
capacitor by a factor of one to infinity. This leads to the definition of a termcalledthe boostfactor,KB,whichgivesan indication
of the 'amplification' of the reactance of the TCSC's internal capacitor
KB=XTCSC/XC--------------- (4)
Where,
KB is the boost factor of the TCSC at the fundamental frequency
XTCSC is the net reactance of the TCSC at the fundamental frequency
Xc is the reactance of the TCSC's internal capacitor at the fundamental frequency
As stated previously, a decrease in the trigger angle of the thyristors results in an increase in the capacitive reactance
of the TCSC, but exactly how this comes about will now be discussed.
Consider the single line diagram of a TCSC shown in Figure1.Iftheforwardbiasedthyristoristriggeredjustbeforethe
TCSC capacitor voltage is zero, then a small circulating current, ITCR will flow in the TCR branch as shown in the figure. This
circulating current adds to the transmission line current flowing through the capacitor, which results in an increase in the
voltage, VCAP, across the capacitor, and an increase in the capacitive reactance of the TCSC
From the discussion above it can be seen that the voltage across the capacitor, andhencethevoltageacrosstheTCR,is
not constant but is dependent on the trigger angle of the thyristors Therefore equation (3) does not accurately predict the
behaviour of the TCSC since equation (1) was developed assuming that the TCR was connected across an ideal voltage source.
The TCSC can operate in one of three modes, depending on the thyristor trigger angle, α. These modes are discussed
below [1]:
4.1 MINIMUM COMPENSATION MODE:
-α = 180° - The thyristors are off and the conduction path of the current is only through thecapacitor,thereforeXTcsc
= Xc. The corresponding boost factor is 1. This is known as the blocking mode and is the case of minimum compensation.

4.2 Bypass mode:
- α = 0° - The thyristors are continuously conducting and this allows current toflowthroughtheinductorandthrough
the capacitor. The capacitor and inductor are now in parallel. X TCSC = -I XcII XL I. The corresponding boost factor is negative
and the TCSC reactance is inductive. This mode is known as the bypass mode, and this mode of operation is used during fault
conditions, when the transmission line current is high, to reduce the stress on the capacitor.
4.3 Capacitive boost mode:
- α = [α res, 180°] - the physical reactance of the capacitor is increased. The reactance of the TCSC is capacitive and is
dependent on the value of α. The boost factor, KB, can vary in the range [00, 1]. This mode of operation is referred to as the
capacitive eboost mode. However, practically a boost factor of KB = 00 is not possible
Figure 4.b. Variation of impedance in case of thyrister controlled series capacitors TCSC
Figure 4.b. shows the impedance characteristics curve of a TCSC device. It is drawn between effective
reactance of TCSC and firing angle α. Net reactance of TCR, XL (α) is varied from its minimum value XL to maximum value
infinity. Likewise effective reactance of TCSC starts increasing from TCR XL value to till occurrence of parallel resonance
condition XL(α) = XC, theoretically XTCSC is infinity.Thisregionisinductiveregion.Furtherincreasingof XL(α)givescapacitive
region, Starts decreasing from infinity point to minimum value of capacitive reactance XC. Thus, impedance characteristics of
TCSC shows, both capacitive and inductive region are possible though varying firing angle (α). [3]
90 < α < αLlim Inductive region
αLlim< α < αClim Capacitive region
αLlim< α < αClim Resonance region [3]
While selecting inductance, XL should be sufficiently smaller than that of the capacitor XC. Since to get both effective
inductive and capacitive reactance across the device. Suppose if XC is smaller than the XL, then only capacitive region is
possible in impedance characteristics. In any shunt network, the effective value of reactance follows the lesser reactance
present in the branch. So only one capacitive reactance region will appears. Also XL should not be equal to XC value; or else a
resonance develops that result in infinite impedance – an unacceptable condition. Note that while varying XL (α), a condition
should not allow to occur XL (α) = XC [3] Figure 4.c. shows a simple transmission line represented by its lumped π equivalent
parameters connected between bus-i and bus-j. Let complex voltage at bus-I and bus-j are Vi and Vj respectively. The real and
reactive power flow from bus-i to bus-j can be written.[3]
Figure 4.c. Model of transmission line.

The control action of the TCSC is usually expressed in terms of its percentage of the compensation, kc, defined as:
Kc=xc/xl *100%
Where, xl is the line reactance and xc is the effective capacitive reactance provided by TCSC.
Ise =V i − V j/rl + j(xl − xc)
The influence of the capacitor is equivalent to a voltage source which depends on voltages V i and Vj. The current
injection model of the TCSC is obtained by replacing the voltage across the TCSC by an equivalent current source Is Figure 4.d.
In Figure 4.e, VS=−jxcIse, and from Figure 4.e. follows
IS=V S/rl+ jxl= −jxc*Ise/rl + jxl Current injections into nodes i and j are
Figure 4.d. Replacement of voltage source by current sourse
Figure 4.e. Current Injection Model of TCSC
ISj= −jxc/rl+ jxl*V i − V j/rl+ j (xl − xc)ISi= −ISj
and therefore the appropriate current injection model of the TCSC can be presented as shown in Figure 4.f.
The general form of the TCSC control system used is shown in Figure 6, where the Control Strategy block represents
the design method for power flow controller based on linearization of power flow equations around an operating point. The
output of the block is the change of the compensation degree given by
∆kc = ∆P (rl2+ (xl− xc) 2)/ {2(Vi2-ViVj cos θij) (1 − kc)...
−r12(ViVj cos θij) 1/xl+ ViVj sin θij (1 − kc)}
where ∆P = Pref − P is the input in the block.
Kcd is the proportional part and Tcd is the integral time constant of the TCSC PI controller. The time constant T
approximates delay due to the main circuit characteristics and control systems.

Figure 4.f. General form of TCSC control system.
TCSC line active power and Pref is the line active power to be maintained byTCSC.Kmin andkmaxarethelimitsonthe
compensation degree changes. [4]
5. CLOSED LOOP CONTROL SCHEMES:
For open loop control of the TCSC impedance, the thyristor trigger angle is set externallyandthecontrollergenerates
the appropriate triggering signal to the thyristors.Thetriggerangleischosendependingonthelevel ofcompensationrequired.
Alternatively, the level of compensation is set externally and the controller determines the appropriate trigger angle from a
look up table or a best fit function.[1]
Numerous low level closed loop control strategies have been proposed to implement a triggering controller
for the TCSC. One of the advantages of a closed loop control system is to speed up the slow response time of the TCSC the slow
response time of the TCSC is due to the effect of the TCR branch and the capacitor [1] in the TCSC.
The closed loop control strategies that have been proposed are closed loop current control,conductionangle
feedback and impedance feedback the feedback signals required for the implementation of these control strategies are the
TCSC capacitor voltage and transmissionlinecurrentforimpedancecontrol,andtheTCRcurrentforconductionanglefeedback
control. An advantage of using the TCSC capacitor voltage as a feedback signal is that possible over-voltage conditions of the
TCSC can also be avoided [1] by monitoring the TCSC capacitor voltage.
Further advantages of closed loop control of the TCSC include the ability to negotiate the effects of the non linear
properties of the TCSC [I], and to reduce the dependency of response on the operating point [1]. It was also proposed [1] that
the transmission line current of each phase be used as a feedback signal and a trigger angle be generated for each phase to
minimize the effects of the dissimilar [2]
6. CONCLUSIONS
With the history of more than three decades and widespread research and development, FACTS controllers are now
considered a proven and mature technology. The recent introduction of TCSC has further widened the scope and added new
valuable benefits. This paper reveals an overview of TCSC as one the best proposed devices in FACTS family, its applications
and the prospects of TCSC as an effective power system improvement tool.
This paper has addresses a quick overview of thyristor controlled series capacitorasonethebestproposeddevices in
FACTS family and its applications in power transmission system. TheperformanceofTCRwasfoundtobehighlydependenton
the Firing angle of the TCR. It was found that as the firing angle increases, results in the consequent reduction of the reactor
current. TCR has the ability to ensure a continuous and fast reactive power and voltage control which can increase the
performance of the system such as control of transients over voltages at power frequency, preventing of voltage collapse, and
increase in transient stability and decrease in system. This paper also presented equipment for controllable series
compensation of transmission lines.

REFERENCES:
[1] A Dsp-Based Digital Controller For Athyristor Controlled Series Capacitor by Anand Pillay B.Sc.Eng.(Electrical).
[2] Verview Of Thyristor Controlled Series Capacitor (Tcsc) In Power Transmission Systeme03421 Mazilah Binti A Rahman
Dvisor Goro Fujita.
[3] Use of FACTS Devices for Power Flow Control and damping of oscillations in Power Systems presented by Rusejla
Sadikovi´C Master of Science, Faculty of Electrical Engineering, and University of Tuzla.
[4] Experimental Study Of Thyristor Controlled Reactor(Tcr) And Gto Controlled Series Capacitor (Gcsc) Jyoti
AgrawalDepartment of Electrical Engineering (M-Tech IV SEM IPS), G.H.Raisoni College Of Engineering, Nagpur Nagpur,
India jyotingp7777@gmail.com K.D.JOSHI Department of Electrical Engineering, G.H.Raisoni College Of Engineering,
Nagpur Nagpur, India kdjoshi22@gmail.comDr. V. K. CHANDRAKAR GHRIETW, Nagpur Nagpur, India.
[5] Study of thyristor controlled series capacitor (tcsc) as auseful facts device md. nasimul islam maruf Lecturer, Stamford
University Bangladesh, Dhaka, Bangladesh A.S.M. MOHSIN Lecturer,Stamford UniversityBangladesh,Dhaka,Bangladesh
MD. ASADUZZAMAN SHOEB Lecturer, Stamford University Bangladesh, Dhaka, Bangladesh MD. KAFIUL ISLAM Jr.
Lecturer, Independent University Bangladesh, Dhaka, Bangladesh MD. MOKARROM HOSSAIN Lecturer, Stamford
University Bangladesh, Dhaka, Bangladesh.
[6] Thyristor Controlled Series Compensator Vasundhara Mahajan*, Department Of Electrical Engineering, M P Christian
College of Engineering & Technology Bhilai, Chhattisgarh, INDIA.
[7] Power System Stability Improvement with Flexible A.C. Transmission System (FACTs) Controller Vasundhara Mahajan.
[8] Enhancing power Flow in H.V. Transmission Line Using TCSC Devices. Mr. K.N. Kazi
and Prof. Mrs. V.V. Khatavkar MCOE, Pune.
[9] Congestion management in high voltage transmission line using thyrister controlled series capacitors (TCSC) Anwar S.
Siddiqui, Rashmi Jain, Majid Jamil and Gupta C.
BIOGRAPHIES
Mr. Ravindra Mukund Malkar is M.E. in Electrical PowerSystemfromWalchandCOE,Sangli(MS).He
is B.E. Electrical from MSBCOE, Latur, (MS). Presently he is working as Assistant Professor in DKTE
Society’s Textile & Engineering Institute, Ichalkaranji, An Autonomous Institute affiliated under
Shivaji University, Kolhapur (MS). His research areas include Harmonics, Transmission Lines and
Power system. He has published and presented the papers in International Journals and
International/National conferences. He is a Life member of Indian Society of Technical Education,
New Delhi.
Mr. Vaibhav Baburao Magdum is M.E. in Electrical Power system from PVGCOET, Pune (MS). He is
B.E. Electrical from AISSMS, COE, Pune, (MS).Presentlyhe is workingas AssistantProfessor in DKTE
Society’s Textile & Engineering Institute, Ichalkaranji, An Autonomous Institute affiliated under
Shivaji University, Kolhapur (MS). His research areas include Electrical Machines, Drives, Power
System, Switchgear & Protection. He has published and presented the papers in International
Journals and International/National conferences. He is a Life member of Indian Society of
Technical Education, New Delhi

IRJET- Optimization of Power Flow in Transmission Line using TCSC Controllers

More Related Content

What's hot (17)

Similar to IRJET- Optimization of Power Flow in Transmission Line using TCSC Controllers (20)

More from IRJET Journal (20)

Recently uploaded (20)

IRJET- Optimization of Power Flow in Transmission Line using TCSC Controllers