It is the science of planning, operating and testing high-voltage electrical devices and designing the insulation coordination in order to ensure the reliable operation of the power network
- 1. www.Vidyarthiplus.com EE 2353 HIGH VOLTAGE ENGINEERING Faculty Name :A.JAIBUNISHA Faculty Code : EE 58 Designation : LECTURER Department : EEE
- 2. UNIT III GENERATION OF HIGH VOLTAGES AND HIGH CURRENTS
- 3. 3 GENERATION OF HIGH D.C VOLTAGE DIFFERENT METHODS TO GENERATE HIGH D,C VOLTAGE: 1. Half and full wave rectifier circuits 2. Voltage doubler circuits 3. Voltage multiplier circuits 4. Van de Graaff generator HALF AND FULL WAVE RECTIFIER CIRCUITS This method can be used to produce DC voltage up to 20 kV For high voltages several units can be connected in series For the first half cycle of the given AC input voltage, capacitor is charged to Vmax and for the next half cycle the capacitor is dischar5ged to the load The capacitor C is chosen such that the time constant CRl is 10 times that of AC supply
- 4. 4 VOLTAGE DOUBLER CIRCUIT In this method, during –ve half cycle, the Capacitor C1is charged through rectifier R to a voltage +Vmax. During next cycle. C1rises to +2Vmax . C2.is charged to 2Vmax. Cascaded voltage doublers can be used for producing larger output voltage
- 5. 5 CASCADED VOLTAGE DOUBLERS Cascaded voltage doublers can be used for producing larger output voltage
- 6. 6 VOLTAGE MULTIPLIER CIRCUITS Here n no. of capacitors and diodes are used. Voltage is cascaded to produce output of 2nVmax . Voltage multiplier circuit using Cockcroft-Walton principle can be used.
- 7. 7 VAN DE GRAFF GENERATOR In electrostatic machines charged bodies are moved in an electrostatic field If an insulated belt with a charge density δ moves in an electric field between two electrodes with separation ‘s’ If the belt moves with a velocity v then mechanical power require to move the belt is P=F.v=V.I
- 8. 8 Electrostatic generator It consists of a stator with interleaved rotor vanes forming a variable capacitor and operates in vacuum The power input into the circuit P=VI=CVdV/dt+V2 dC/dt The rotor is insulated from the ground,maintained at a potential of +V. The rotor to stator capacitance varies from C0 to Cm Stator is connected to a common point between two rectifiers across –E volts. As the rotor rotates, the capacitance decreases and the voltage across C increases. Output voltage of 1MV can be generated.
- 9. 9 GENERATION OF HIGH ALTERNETING VOLTAGES When test voltage requirements are less than about 300 kV,a single transformer can be used. Each transformer unit consists of low,high and meter winding. Series connection of the several units of transformers used to produce very high voltage.
- 10. 10 CASCADE TRANSFORMERS First transformer is at ground potential along with its tank.The 2nd transformer is kept on insulators and maintained at a potential of V2. The high voltage winding of the 1st unit is connected to the tank of the 2nd unit,the low voltage winging of this unit is supplied from the excitation winding of the 1st transformer,which is in series with the high voltage winding of the 1st transformer at its high voltage end. The rating of the excitation winding is same as that of low voltage winding.3rd transformer is kept on insulator above the ground at a potential of 2V2.output of 3 stage is 3V2. The rating of the low voltage winding of 230 or 400 Vcan be used to produce 3.3 kV,6.6 kV or 11 kV.
- 11. 11 GENERATION OF HIGH AC VOLTAGE CASCADE TRANSFORMER
- 12. 12 GENERATION OF HIGH AC VOLTAGE Cascade transformer with isolating transformer for excitation
- 13. 13 GENERATION OF HIGH FREQUENCY A.C HIGH VOLTAGES High frequency high voltage damped oscillations are needed which need high voltage high frequency transformer which is a Tesla coil. Tesla coil is a doubly tuned resonant circuit,primary voltage rating is 10 kV and secondary voltage rated from 500 to 1000 kV. The primary is fed from DC or AC supply through C1.A spark gap G connected across the primary is triggered at V1 which induces a high self excitation in the secondary.The windings are tuned to a frequency of 10 to 100 kHz.
- 14. 14 GENERATION OF IMPULSE VOLTAGES STANDARD IMPULSE WAVESHAPE It is specified by rise or front time,fall or tail time to 50% peak value and peak value. 1.2/50 μ s,1000 kV.
- 15. 15 MARX CIRCUIT Charging resistance Rs is liming the charging current from 50 to 100 mA. CRs is about 10s to 1 min. The gap spacing G is grater than the charging voltage V.All the capacitance s are charged to the voltage V in 1 min. The spark gap G is made spark over, then all the capacitor C get connected in series and discharge into the load load In modified Marx circuit,R1is divided into n parts equal to R1/n and put in series with the gap G, R2is divided into n parts equal to R2/n and connected across each capacitor unit after the gap G. The nominal output is the number of stages multiplied by the charging voltage.
- 16. 16 MULTISTAGE IMPULSE GENERATOR MARX CIRCUIT A single capacitor C1 is to be charged first and then discharged into wave shaping circuits and it is limited to 200 kV For producing very high voltages a bank of capacitors are charged in parallel and then discharged in series.
- 17. 17 MULTI STAGE IMPULSE GENERATORS Modified Marx Circuit
- 18. 18 COMPONENTS OF A MULTISTAGE IMPULSE GENERATOR DC Charging set Charging resistors Generator capacitors and spark gaps Wave shaping resistors and capacitors Triggering system Voltage dividers
- 19. 19 GENERATION OF SWITCHING SURGES A switching surge is a short duration transient voltage produced in the system due to a sudden opening or closing of a switch or c.b or due to an arcing at a fault in the system. Impulse generator circuit is modified to give longer duration wave shape,100/1000 μs,R1 is increased to very high value and it is parallel to R2 in the discharge circuit. Power transformer excited by DC voltages giving oscillatory waves which produces unidirectional damped oscillations.Frequency of 1to 10 kHz Switching surges of very high peaks and long duration can be obtained by one circuit,In this circuit C1 charged to a low voltage d.c(20 to 25 kV) is discharged into the low voltage winding of a power transformer.The high voltage winding is connected inparallel to a load capacitance C2,potential divider R2,gap S and test object.
- 20. 20 GENERATION OF IMPULSE CURRENTS For producing impulse currents of large value,a bank of capacitors connected in parallel are charged to a specified value and are discharged through a series R-Lcircuit. Im=V(exp(-αt))sin(ωt)/ωL
- 21. 21 GENERATION OF HIGH IMPULSE CURRENTS For producing large values of impulse,a no.of capacitors are charged in parallel and discharged in parallel into the circuit. The essential parts of an impulse current generator are: (i) a.d.c. charging unit (ii) capacitors of high value (0.5 to 5 μF) (iii) an additional air cored inductor (iv) proper shunts and oscillograph for measurement purposes, and (v) a triggering unit and spark gap for the initiation of the current generator.
- 22. 22 TRIPPING AND CONTROL OF IMPULSE GENERATORS In large impulse generators, the spark gaps are generally sphere gaps or gaps formed by hemispherical electrodes. The gaps are arranged such that sparking of one gap results in automatic sparking of other gaps as overvoltage is impressed on the other. A simple method of controlled tripping consists of making the first gap a three electrode gap and firing it from a controlled source.
- 23. 23 TRIPPING AND CONTROL OF IMPULSE GENERATORS The first stage of the impulse generator is fitted with a three electrode gap, and the central electrode is maintained at a potential in between that of the top and the bottom electrodes with the resistors R1 and RL. The tripping is initiated by applying a pulse to the thyration G by closing the switch S. C produces an exponentially decaying pulse of positive polarity. The Thyraton conducts on receiving the pulse from the switch S and produces a negative pulse through the capacitance C1 at central electrode. Voltage between central electrode and the top electrode those above sparking potential and gap contacts.
- 24. 24 TRIPPING CIRCUIT USING A TRIGATRON This requires much smaller voltage for operation compared to the three electrode gap. A trigatron gap consists of a high voltage spherical electrode, an earthed main electrode of spherical shape, and a trigger electrode through the main electrode. Tripping of the impulse generator is effected by a trip pulse which produces a spark between the trigger electrode and the earthed sphere. Due to space charge effects and distortion of the field in the main gap, spark over of the main gap occurs and it is polarity sensitive.