LASSO MODELING AS AN ALTERNATIVE TO PCA BASED MULTIVARIATE MODELS TO SYSTEM WITH HEAVY SPARSITY: “BIODIESEL QUALITY BY NIR SPECTROSCOPY”

Applied Mathematics and Sciences: An International Journal (MathSJ), Vol. 7, No. 1, March 2020
DOI : 10.5121/mathsj.2020.7101 1
LASSO MODELING AS AN ALTERNATIVE TO
PCA BASED MULTIVARIATE MODELS TO
SYSTEM WITH HEAVY SPARSITY: “BIODIESEL
QUALITY BY NIR SPECTROSCOPY”
Cesar Mello1
, Cassiano Escudeiro1
, and Isao Noda2
1
Integrated Institute of Clinical Research - IPclin, Jundiai, State of São Paulo, Brazil.
2
Department of Materials Science and Engineering, University of Delaware, Newark,
DE, USA.
ABSTRACT
Principal component analysis (PCA) is a widespread and widely used in various areas of science such as
bioinformatics, econometrics, and chemometrics among others. Once that PCA is based in the
eigenvalues and the eigenvectors which are a very weak approach to high dimension systems with
degrees of sparsity and in these situations the PCA is no longer a recommended procedure. Sparsity is
very common in near infrared spectroscopy due to the large number of spectra required and the water
absorption broad bands what makes these spectra very similar and with heavy sparsity in matrix dataset,
demoting the precision and accuracy, in the multivariate modeling and within projections of data matrix
in smaller dimensions. To overcoming these shortcomings the LASSO, a not PCA based method, model
was applied to a NIR spectra dataset from Biodiesel and its performance was, statistically, compared
with traditional multivariate modeling such as PCR and PLSR.
KEYWORDS
lassomodel, sparsity, multivariate modeling, NIR spectroscopy, biodiesel from recyclable sources.
1. INTRODUCTION
The multivariate modeling is a traditional chemometric tool and very useful to build models
near infrared (NIR) spectroscopy data sets to ensure products quality and to evaluate, in a very
fast way, the performance of industrials processes, in many areas, such as foods, fuels and
polymers, for short. This spectroscopy technique provides fast, noninvasive and nondestructive
analysis of samples, predicting a large number of samples properties, from NIR spectra [1]. The
great majority of multivariate modeling use, at least in initial steps, the principal components
analysis (PCA) [2]. The PCA based methods are very important especially in spectroscopy data
sets, where the number of independent variables is greater than the number of acquired spectra;
the equations system is overdetermined. However, PCA based methods as principal component
regression (PCR) [3] and partial least squares regression (PLSR) [4] have at least two important
shortcomings, when the matrix from NIR dataset tends to sparsity and the relationship among
the sample properties and spectra, is lightly nonlinear. At this point in this text, it is important to
make it clear that when we refer to matrix from NIR spectra set, we are referring to correlation
matrix (C) calculated by the following steps:
i. Data centering on average:
𝑥𝑖,𝑗 = 𝑥𝑖,𝑗 − 𝑥𝑗 (1)

2
𝑎𝑢𝑡𝑜𝑠𝑐𝑎𝑙𝑒𝑑
Where𝑥𝑗 is the average of the j-th column of data.
𝑥 =
1
∑𝐼 𝑥 (2)
𝑗 𝐼 𝑖=1 𝑖,𝑗
Aondeié o número de linhas,j o número de colunas e Io número total de colunas.
ii. Autoscale
𝑥𝑖,𝑗 =
𝑥𝑖,𝑗−𝑥𝑗
𝑠𝑗
(3)
Where S is the standard deviation from data matrix (X)
iii. Correlation matrix C
𝐶 =
𝑋𝑇
∙𝑋𝑎𝑢𝑡𝑜𝑠𝑐𝑎𝑙𝑒𝑑
𝐼−1
(4)
Although some authors claim that their PCR and PLSR models can to model small
nonlinearities and sparsity in very small degree, with the addition of extra principal components
(PC's). However in practice, external disturbances such as light scattering, baseline fluctuations
and noise, for short, will introduce nonlinearities and increasing to the sparsity in spectral data,
deteriorating the prediction accuracy step and precision from PCR and PLSR modeling.
However, in many cases it is possible to minimize these sources of nonlinearities in a very
effective way. There are several mathematical techniques to do these tasks such multiplicative
scattering correction (MSC)[5], noise minimization by Fast Fourier Transform (FFT) [6] or
wavelets filter[7] Gram-Schmidt orthogonalization [8] and detrend baseline correction[9] just to
name a few. Such methods of pre-processing spectral data set, allow the use of PCA based
models without great problems.However, the spectroscopic technique NIR presents several
shortcomings very difficult to overcoming. The intrinsic NIR broad absorption bands called
overtones and highly undesirable effects due to water absorption broad bands making the NIR
spectra a very broad bands spectrum, referred as overtone bands, of difficult Physical and/or
Chemical interpretation and analysis. This broad band affects the NIR spectrum as whole
making the NIR spectra from the same sample very similar, with heavy overlaps. All of these
physical effects, together, such effects together, generate heavy sparsity in C. In such cases the
PCA based multivariate modeling methods completely lose accuracy and precision, with orders
of magnitude dependent on the system under evaluation. Moreover, in such cases it is necessary
to acquire a large number of NIR spectra for prediction and validation procedures of these
models.
Thus we have a reasonably complicated situation, that is, a large data matrix with heavy
sparsity. Accordingly, in such cases multivariate modeling methods based on principal
component analysis can fail. Therefore, in such cases it is recommended to analyze, previously,
the asymptotic behavior of the Principals Components i.e. the direction of the main components
(PC's) into large dimension systems as in matrices from NIR spectroscopy dataset. The
asymptotic behavior analysis basically shows that if the first few eigenvalues of a population
covariance matrix are large enough compared to the others, then the corresponding estimated
PC directions are consistent or converge to the appropriate subspace and most other PC
directions are strongly inconsistent, that is, such PC's do not have anything physical meaning.
After such mathematical analysis one can decide on whether it is possible to use PCA or not.
However it is much simpler to use C to calculate its condition number before applying to PCA.
Thus, in a first approximation one can establish the very simple rule to the use of the PCA by
calculating the condition number (CN) [10] from NIR matrix of dataset. However a little bit
further analysis over CN from C it is necessary. The CN from a matrix is a measure of whether

3
the problem has "good condition" to be treated numerically. A problem with a small CN is
called well-conditioned, while problems that have a high condition number are called poorly
conditioned due to, among others effects, the sparsity. For example, the CN associated with a
linear system is a number that estimates the accuracy that can be obtained for an approximate
solution of the system. Note that this is before the effects of rounding errors are taken into
account. Paired with this problem there are any number of algorithms that can be used to solve
such kind of problem, that is, to calculate the solution. Some numeric algorithms have a
property called backward stability. In general, a backward stable algorithm can be expected, to
accurately solve, only, well-conditioned problems. However, CN is an intrinsic property of the
C and we can use the following simple rule of thumb: if the CN is small them is possible, in a
first approximation, to apply to principal component analysis (PCA) and to use the traditional
and well established multivariate models like PCR and PLSR.However, this type of
mathematical analysis is a little cumbersome and very unusual in daily use of NIR so it is much
more practical and efficient to use the LASSO modeling as a choice method. Despite the
possible difficulties mentioned above, the PCA is still an ordinary and very efficient
mathematical method for dimensionality reducing from the spectral data set with the
shortcomings aforementionedand the vast majority of NIR spectrometers have software to
perform PCA based methods such as PCR and PLSR, among others. The widespread use of
these nonparametric methods relies on its easy computational implementation, and such
methods, in general, are algorithmic methods. In the 1980s, routine interactive computing was
just beginning to raise its head, and exploratory data analysis was a new idea. Since then, we
have witnessed a number of remarkable developments in local computing power and data
storage. Besides that, efficient and interactive chemometrics packages have enabled
sophisticated data analyses to carry out eﬀortlessly and the vast majority of NIR spectrometers
have software to perform PCA based methods such as PCR and PLSR, among others. However
such kind of nonparametric methods provide approximates solutions and not necessarily robust
ones, causing a lot of wrong solutions and misinterpretations even in quite simple
systems.These nonparametric methods are not robust inmathematically sense due to its high
sensibility to the nonlinearities, outliers and heavy sparsity in C. Hence, before using the
nonparametric methods, it might be a good strategy to analyze the sparsity of C, before building
PCA based models as extensively mentioned.In this work, a parametric method not largely
usedin multivariate modelingmainly in, at least,three very important areas such as
chemometrics, econometrics and financial sciences, called Least Absolute Shrinkage, Selection
Operator (LASSO) was used and its performance was evaluated against models done with PCR
and PLSR.The LASSO method, also reduce the dimensionality of a data set such as PCA does,
but using a different mathematical approach as we will describe ahead [11, 12]. The LASSO
method, also reduce the dimensionality of C such as PCA does, but using a different
mathematical approach as we will describe ahead. PCR and PLSR as along with LASSO
method were used to build multivariate calibration models to determinate the percentage in
mass (w/w) of Biodiesel[13], from animal fat recyclable sources, contained in Diesel B20,
which is a complex blend of soybean, animal fat Biodiesel and petroleum Diesel. Depending on
the percentage (w/w) of animal fat Biodiesel and operational temperatures, it can cause several
and different engine failures. Hence, the multivariate modelingvery robust, less sensitive to
outliers and mainly sparsity is a very attractive alternative to determine the content of animal fat
Biodiesel in Diesel B20, by NIR spectroscopy, to improve the quality control of fuel to avoiding
operational failures related to the Diesel quality, in engine vehicles. Nowadays, the use of
multivariate modeling in modeling NIR spectroscopic data sets is widely employed, being
considered a standard procedure for quantitative analysis in several analytical techniques and
precisely because of this fact, very robust multivariate modeling methods with low sensitivity to
sparsity of the NIR spectra matrix should be used.

4
j=1
i=1
1.1. The LASSO Modeling
The LASSO method is a hybrid of variable selection and shrinkage estimators. The procedure
shrinks the coefficients of some of the variables not simply towards zero, but exactly to zero,
giving an implicit form of variable selection. In the simple standard multiple regression we have
the Eq.5:
yi = λ0 + ∑p λj . xij + ε (5)
where y1, y2,..., yn are measurements on a response variable y; xij, i = 1, 2, … ,n, and j = 1,
2,... , p, are corresponding values of p predictor variables; λ, λ0, λ1, … , λ𝑝 are the parameters in
the regression of the Eq.5. The ε value is an error term. In least squares regression, the
parameters are obtained minimizing the residual sum of squares:
min. ∑n (yi − λ0
p
j=1
2
λjxij) (6)
The LASSO modeling imposes an additional restriction on the coefficients, namely:
∑n |λj| ≤ 𝑡 (7)
j=1
Thus in LASSO modeling we have a typical problem of constrained minimization problem
where λ is a kind “tuning parameter”, suitable choices of this constraint, t, has an interesting
property, which forces some of the coefficients in the regression equation to become zero. The
computation of the solution to Eq.6, with the restriction given by Eq.7 is a quadratic
programming problem with linear inequality constraints. There are several efficient and very
stable algorithms for solving this kind of inequality problem. Finally, it is possible to summarize
the LASSO theory as a simple ordinary least square(OLS)[14] with restrictions leading to an
exact solution, obtained by quadratic programming. The LASSO parametric method was
applied in this work to build a direct modeling to a spectral data set with one hundred of NIR
spectra, to determine the percentage of animal fat Biodiesel in Diesel B20. However, it can be
used to C with two, three hundred or even more NIR spectra. Finally, the results were compared
with two traditional nonparametric methods, the partial least square regression(PLSR) and
principal component regression (PCR).
2. EXPERIMENTAL
The process of producing biodiesel from renewable natural sources is well established and
widely knownand references can be found anywhere as aforementioned. Therefore, it is not
necessary to present in great detail such a process in this work. We emphasize once again that
the most important is the evaluation of biodiesel produced through NIR spectroscopy. With this
fact in mind the experimental part can be simplified. Therefore,experimental part can be
simplified. Aset of one hundred blends of Diesel B20 and animal fat Biodiesel were initially
prepared, with different concentrations of animal fat Biodiesel in Diesel B20.The animal fat
Biodiesel content in Diesel B20 ranged from 0.00% to 13.80 %(w/w), where the Diesel B20 is a
blend of soybean Biodiesel and petroleum diesel, containing at most 50 ppm in mass of sulfur.
Near infrared (NIR) spectra were acquired, after each addition of animal fat Biodiesel using a
NIR spectrometer Perkin Elmer 100N spectrometer equipped with a liquid reflectance accessory
in the range from 4,000 to 400 cm-1
using aresolution of 4 cm-1
and 64 scans per sample. All
samples were acquired in triplicate and the average spectrum was used to build the calibration
model. The set of one hundred NIR spectra was splitted into two data sets, using the
Kenston[16] algorithm, one of them for calibration with 70 samples and the other one with 30
samples, for predictions and modeling validation. The C was pre-processed, using MSC and the
− ∑

5
noise was minimized by using Fast Fourier Transformfilter. All computational procedures were
performed with routines developed in GNU Octave 5.1.0 [15].
3. RESULTS AND DISCUSSION
Using the above procedure, in materials and methods section, a set of one hundred NIR spectra,
were acquired in reflectance mode. To better visualization the usual transformation in the
reflectance measurements (R), was applied:
𝐿𝑜𝑔
1
𝑅
Eq.8
The set of spectra was plotted with 𝑙𝑜𝑔 1⁄𝑅 in abscises and the wavenumbers in cm-1
in the
ordinates, as shown the Figure 1.
Figure 1. The NIR Spectra obtained for 99 additions of animal fat Biodiesel in Diesel B20, and one with
pure Diesel B20, in a final set of 100 NIR spectra.
The coefficients λwere calculated using simple quadratic programming [16], as shown in the
Figure 1. The Figure 2 points out the shrinkage of the coefficients (λ) to zero, as described in the
introduction of LASSO method.
Figure 2. Graphical representation of the Lambda (λ) set values fitted by LASSO against degrees of
freedom (df).
In the Figure 2 is shown λ valuesobtained by cross-validation. The cross validation was done by
using blocks [17], since it is impossible to use the leave one out (LOO)scheme for LASSO
method.

6
Figure 3. Plot of λ against mean square error (MSE), to choose the λ value with MSE.
The calibration curve obtained using the LASSO method with in the values of the abscissas
being the actual value of %(w/w) animal fat Biodiesel and the values in the ordinates, the
obtained values of % (w/w) animal fat Biodiesel from LASSO modeling. The merit figures are
inside of the Figure 4.
Figure 4. Plot of calibration curve obtained by Lasso method. The goodness of fit is show inside the
figure; 𝑅2 = 0.9999.
The plot of Q residuals vs. Hoteling’s T2
statistic gives a compact view of both, residual and
score outliers (as well as inliers). The axis shows that scores capture 90.25% (abscises) of the
total variance and 9.75% (ordinates) of the variance remains in the residuals. TheFigure 5 shows
there are not so many scores outliers; some of them present a small value. As can be observed in
the Figure 5 there, the LASSO method outperforms the PCA-based models, because the
presence of some outliers does not degrade the performance as it does in PCAbased models.
Figure 5. Plot of Hoteling T2
test to verify the presence of outliers.

7
A possiblesolution for PCA based models is to remove the outliers before, which is a
cumbersome and in some sense,a subjective task. Moreover, it is essential to emphasize that a
reduction in the size of the data set also reduces,at same time, the performance of the PCA
based methods due to condition number, is always a trade-off. Nevertheless, if it is necessary to
remove some outliers, it is possible to apply a heuristic method to remove them from the large
data set. This heuristic method is quite simple; manually removing the outliers whose values are
very discrepant in the data set. Such heuristic method goes against one of the main idea of
chemometrics, which is to extract maximum information with a minimal experimental and
subjective work. In cases in which the data set are small, as observed in many chemometrics
applications, perhaps the best way is to keep all outliers and hope that the error does not
increase so much. The LASSO method is a very robust alternative for these cases, that is, do not
show high sensitivity to outliers, especially for small datasets. The optimal number of Principal
Component (PC’s) values to PCR werecalculated by cross-validation using the LOO method.
From the Figure 6 is easy to choose the optimal number of PC’s, four to this data set. Using the
parsimony principle and observing that after the value 4 the curve of RMSECV/RMSEC against
PC's tend toward asymptotically to a constant value as shown in the Figure6.
Figure 6. Plot of root mean square error for calibration (RMSEC) and root mean square error for cross
validation samples (RMSECV), for PCR using model leave one out method.
The Figure 7 shown the calibration curve to PCR, in the values of the abscissas are the
actual value of %(w/w) animal fat Biodiesel, and in the values of the ordinates are the
obtained values of %(w/w) animal fat Biodiesel, with PCR model. The goodness of fit
is inside the Figure 7.
Figure 7. Plot of calibration curve obtained by PCR method, the goodness of fit are show inside of the
figure;2 = 0.9298.

8
The optimal number of latent variables (LV’s) value to PLSR was obtainedby cross-validation
using the LOO method.From the Figure 8 is easy to choose the optimal number of LV’s, such
that for this data set,these number is around four or five once that after these values of
RMSEC/RMSECV the curve tend asymptotically to zero. Then, using the parsimony principle
of was chosen four LV’s to build the PLSR model.
Figure 8. Plot of (RMSEC) and (RMSECV), for PLSR using model leave one method.
The calibration curve for PLSR shown in the Figure 9,in the abscissas values are the actual
valuesand in the values of the ordinates are the obtained values of %(w/w) animal fat Biodiesel,
with PLSR model. The merit figures are shown inside of the Figure 9.
Figure 9. Plot of calibration curve obtained by PLSR method, the goodness of fit are shown in the
figure;2 = 0.9918.
The next three graphics (Figures 10, 11 and 12), the models obtained will be further checked,
evaluating the possible presence of overfitting orunderfitting. Such assessment will be
performed in a simple, but statistically efficient and correct way. This procedure will be carried
out by fitting a normal probability distribution function for to fit the residues leave of each one
model performed in this work. Naturally, a model with thebest fit to the experimental data set
should show invariably residues with a tendency to a perfect Gaussian distribution shape in
ideal conditions. In Figure 10 it is possible to observe that the model obtained with PCR leaves
an approximate Gaussian distribution without tail. The Gaussian fit of the residues indicates
clearly that the PCR model does not present overfitting or underfitting.

9
Figure 10. Gaussian fit of residues leave by PCR, the goodness of fit are shown in the Figure 10; 𝑥 =
427562 10−14 = 4.7562 and 𝑠 = 1,1381.
In Figure11 it is possible to observe that the model obtained withPLSR leaves a Gaussian
distribution with a light tail, indicating that the PLSR model presents a small overfitting and/or
underfitting.
Figure 11. Gaussian fit of residues leave by PCR, the goodness of fit are shown in the Figure 10;
𝑥 = 1,6954 10−14 and 𝑠 = 1,1381.
A definitive discussion about a comparative approach of ,PCR against PLSR is not a
simple task, once that there are so many possible interpretations to overfitting or
underfitting. However is possible to point out, specifically for this dataset without being
flippant, that the PCA applied for independent variables revealed a poor performance,
possibly due to the size of data set. There is no consensus, in the literature, to explain
the better performance of PCR than PLSR in some data sets, since the optimal number
of LV’s was chosen by cross validation, as shown in Figure 8. Perhaps, if the dataset
was larger, the light tail would not happen. However, obtaining a large data set is not a
good idea too, as aforementioned and this little overfitting presented by PLSRmodel, is
not a big problem for practical purposes, once that, local models have been constructed
for both kind of model and in this range of concentrations PLSRmodel is valid and
useful too.
In Figure13 it is possible to observe that the model obtained withLASSO leaves a
Gaussian distribution with a very light tail as PLSR, indicating clearlythat the LASSO
model present a smaller overfitting and/or underfitting than PCR and PLSR Models in
an overall way.

10
Figure 12. Gaussian fit of residues leave by PCR, the goodness of fit are shown in the Figure 10;
𝑥 = 1,2093 10−14 and 𝑠 = 0,0629.
The relative performances from different models, was evaluated in terms of root-mean-square-
error (RMSE): 2 (y - y
̂ )
2
RMSE= √ i model, i
n-1
(9)
Where is the actual value and ̂is the predicted value by the model and n is the number of the
samples used, in the prediction set. A very simple analysis of RMSE values, shown in Table 1,
indicates that the LASSO method was the most efficient multivariate modeling, followed by
PLSR and PCR respectively.
Table 1. Results of RMSE for different types of models evaluated: LASSO, PLSR and PCR.
Model
LASSO 0.1133
PLSR 0.3646
PCR 1.3040
A very simple analysis of RMSE values, shown in Table 1, indicates that the LASSO method
was the most efficient calibration method, followed by PLSR and PCR respectively. Such
differences observed in the models, are due to the nature of the methods and size of NIR
spectroscopy data set used in this article. The parametric model carried out with the LASSO
method has a very robust numeric solution while the nonparametricPLSR and PCR models are
PCA based methods, which, in some data sets, provides a mathematically weak and unstable
approximated solution. Perhaps, if the data used in this article was larger, the results obtained
with the nonparametric model could be approximately equal to the parametric method LASSO.
It is possible to affirm that the nonparametric methods used in this article are very sensible to
outliers and the size of data set, that is, they are not robust methods for small data sets or ill
conditioned data set. To check if such the assumptions previously made are correct anF-test
[18], with 95% confidence level wasused to compare RMSE for the differentmultivariate
modeling used in this article, the F-test is given by Eq.10:
𝐹(𝑝𝑖, 𝑝𝑗) =
(
𝑅𝑀𝑆𝐸𝑝𝑎𝑟𝑎𝑚𝑒𝑡𝑟𝑖𝑐𝑚𝑜𝑑𝑒𝑙,𝐿𝐴𝑆𝑆𝑂
)
𝑅𝑀𝑆𝐸𝑁𝑜𝑛−𝑝𝑎𝑟𝑎𝑚𝑒𝑡𝑟𝑖𝑐𝑚𝑜𝑑𝑒𝑙,𝑃𝐶𝑅 𝑎𝑛𝑑 𝑃𝐿𝑆𝑅
(10)
2

11
Where,p is the number of validation samples, in our case p = 30. The F-test critical value at the
95% confidence level is Fcritical= 1.61. When the F-test is applied to the RMSE values obtained
from different modeling methods, it is observed that theLASSO model is significantly better
than PLSR (F= 2.1) and PCR (F = 2.4). Despite of thebest performance, LASSO is a little bit
more difficult to implement, computationally,its require more computational time, around 1
minute while the PLSR and PCR modeling only few seconds. However, this statement may not
have a long life since the new low cost microcomputers and new numerical algorithms that are
more efficient have grown exponentially, in addition to enhanced processing power, what is
drastically reducing CPU use time.
4. CONCLUSIONS
Based on the results obtained and in the discussion before, it is possible to conclude that the
method LASSO showed better results than nonparametric methods, like PCR and PLSR, due to
size of data set as aforementioned. Another very important outcome about PCA based inverse
models is the necessity of repeat the NIR spectrometer calibration frequently. Once that with the
pass of the time and the high use of NIR spectrometer the internal calibration is lost and the NIR
spectra are no longer reliable. When we decided to use the LASSO method as multivariate
modeling method for the quality determination of Biodiesel by NIR spectrometry, our intention
was not only to evaluate the use NIR spectroscopy applied to the quality of Biodiesel but also
verify if the LASSO method overcomes the performance of traditional inverse chemometrics as
PCR and PLSR. Although we have presented the main advantages of the LASSO over PCA
based methods in spectroscopic datasets where the CN is large, the LASSO method can present
severe discrepancies if the distribution of regression errors shows a heavy tail for a finite
sample. Sparse principal component analysis (SPCA) aims at estimating a PCA-like model
where sparsity is induced on the model parameters; scores and / or loadings. However, this is
still an algorithm-based method, the PCA, without an exact solution. The SPCA works
reasonably well in certain types of spectroscopy, such as mass spectroscopy where the
spectroscopy matrix dataset, can have its sparsity reduced experimentally, only in some cases,
using spectrometers of high accuracy and precision, as well as chemical standards of very high
purity , making the very high-priced method accessible only in big researcher centres,
inaccessible to the vast majority of researchers worldwide. Therefore, the SPCA goes in the
opposite direction of the PCA-based methods which were developed, precisely, to obtain
calibration models in situations where high instrumental accuracy was not possible or important,
as occurred in the NIR spectroscopy in the early 80s. However, the purpose of this article is not
to criticize the use of the PCA or SPCA-based methods [19], but to present alternatives with
exact solutions concerning purely algorithmic methods.
The better results obtained with LASSO method shown clearly that PCA based models had an
important shortcoming to data sets with tendency to sparsity, which is quite usual in diary
practical situations of NIR spectroscopy in reflectance mode. Besides that, the LASSO is a very
simple alternative to PCA based models where the matrix describing the spectroscopic data set
tends to become still sparser. Finally, it is possible to notice that the parametric methods works
better in presence of outliers than nonparametric methods, such PCR and PLSR.
5. ACKNOWLEDGEMENTS
The Authors thanks to FAPESP, CNPq, University of Delaware and Institute for Integrated
Clinical Research – IPclin.

12
REFERENCES
[1] Siesler, H. W. , Y. Ozaki and Kawata, S. , (2001) “Near‐Infrared Spectroscopy: Principles,
Instruments”, Applications, Wiley-VCH Verlag Gmbh.
[2] Jolliffe, I.T., 2nd edition, (2002), “Principal Component Analysis”, Spring.
[3] R, De Maesschalck, F, Estienne ,Verdú-Andrés, Candol. J, Centner V. A. ,Despagne, F., D. Jouan-
Rimbaud, Walczak. B. ,Massart , D.L., de Jong, S, de Noord, O.E , Puel, C, Vandeginste, B.M.G.
[4] Brereton, R. , Jansen, J. , Lopes, J., Marine, F., Pomerantse, A., Rodionova O., Roger, M. J., Walczak,
B. and Tauler. R.( 2018), Anal. and Bioanal. Chem., Vol. 410 (26), pp 540-543.
[5] Naes, T., Isaksson, T and Kowalski, B., (1990), Anal. Chem. Vol. 62(7), pp.664-673.
[6] Mello. C.; Ozório, E.; Kubota, L. T.; (2000), Química Nova, 2000, Vol. 25, pp690-698.
[7] RIsmail, A.; SAsfour. S. (1999), Jour. Biomech., Vol. 32, pp317-322
[8] Å.Björck., (1994), Linear Algebra and its Applications, Vol. 197-198, pp. 297-316.
[9] Tanabe. J.; Miller. D.; Tregellas. J.; Freedman. R. and Mayer. F.G. (2002); NeuroImage, Vol. 15, pp-
902-907.
[10] Charpentier. S.; Fouchet. K and Zarouf. S. (2019), Analysis and Mathematical Physics, Vol.9 (3), pp-
971-990.
[11] Friedman. J; Hastie. T. and Tibishirani. R.,(2008) Biosataistics,Vol. 9, pp432-441
[12] Horowitz. J. L. (2019), Annual Review Economics, Vol. 11, pp193-224.
[13] Knothe. G (Editor), Krah. Jl (Editor), Van Gerpen. J (Editor), (2010). “The Biodiesel Handbook”,
Academic Press and AOCS Press.
[14] Goldberger, A. S. (1964). "Classical Linear Regression". Econometric Theory. New York: John
Wiley & Sons. pp. 158.
[15] Pencheva. T ;Atanassov. K and Shannon. A. Anthony ; Tenth Int. Workshop on Generalized Nets Sofia,
5 December 2009, 1-7.
[15] http://www.gnu.org/software/octave/doc/interpreter/, last accessed in November 2019.
[16] Marguerite. F. and Wolfe P.; "An Algorithm for Quadratic Programming." Naval Research Logistics
Quarterly 3 (1956): 95-110. Web. 4 June 2015.
[17] Wülfert.F; Kok. T. W; de Nood. O. E.andSmilde A. K.(2000), Chemon. Intell. Lab. Sys., Vol. 24 (2),
pp189-200.
[18] Box, G. E. P. (1953). "Non-Normality and Tests on Variances". Biometrika. Vol.40 (3/4), pp318– 335.
[19] Gajjar, S.; Kulahci, M. and Palazoglu. A., (2016), “Use of Sparse Principal Component Analysis
(SPCA) for Fault Detection”, IFAC,pp 693-698, 11th IFAC Symposium on Dynamics and Control of
Process Systems, including Biosystems June 6-8, 2016. NTNU, Trondheim, Norway

LASSO MODELING AS AN ALTERNATIVE TO PCA BASED MULTIVARIATE MODELS TO SYSTEM WITH HEAVY SPARSITY: “BIODIESEL QUALITY BY NIR SPECTROSCOPY”

More Related Content

Similar to LASSO MODELING AS AN ALTERNATIVE TO PCA BASED MULTIVARIATE MODELS TO SYSTEM WITH HEAVY SPARSITY: “BIODIESEL QUALITY BY NIR SPECTROSCOPY” (20)

More from mathsjournal (20)

Recently uploaded (20)

LASSO MODELING AS AN ALTERNATIVE TO PCA BASED MULTIVARIATE MODELS TO SYSTEM WITH HEAVY SPARSITY: “BIODIESEL QUALITY BY NIR SPECTROSCOPY”