nonClonableID™ Reader SX21 User Manual

Reader SX21
User Manual
Bilcare Technologies Singapore Pte Ltd
10 September, 2009
Document Number: 21
Reproduction, transfer, distribution or storage of
part or all of the contents in this document in any
form, without the prior written permission of Bilcare
Technologies Singapore Pte Ltd, is prohibited. Herein
“Bilcare Technologies Singapore Pte Ltd” is referred to
as “Bilcare Technologies”.
NOTE: although this product can be used with a wide
variety of products, throughout this manual blister
packs are used as the example product.
Copyright © 2009, Bilcare Technologies.
All rights reserved. Specifications subject to change without
notice.

2 3
The products and company names mentioned in this
document are trademarks or registered trademarks of
their respective owners.
Bilcare Technologies operates a policy of continuous
development. Bilcare Technologies reserves the
right to make changes and improvements to any of
the products described in this document without
prior notice. Under no circumstances shall Bilcare
Technologies be responsible for any loss of data or
income or any special, incidental, consequential or
indirect damages howsoever caused.
The contents of this document is provided ‘as is’.
Except as required by applicable law, no warranties of
any kind, either express or implied, including, but not
limited to, the implied warranties of merchantability
and fitness for a particular purpose, are made in
relation to the accuracy, reliability or contents of this
document. Bilcare Technologies reserves the right to
revise this document or withdraw it at any time without
prior notice.
This Reader may contain commodities, technology, or
software subject to export laws and regulations from
Singapore and other countries.
Reverse engineering of any software or hardware
associated with the nonClonable™ system is
prohibited to the extent permitted by applicable law.
The nonClonable™ system is protected by granted
and pending international patents including WO
2007/133164 A1 and WO 2007/133163 A1.
SAFETY WARNINGS
CAUTION PRODUCT CONTAINS A LASER
This product contains a Class 1M laser and the casing
should not be opened or tampered with to avoid
possible exposure to the laser.
INVISIBLE LASER RADIATION
DO NOT VIEW DIRECTLY WITH
OPTICAL INSTRUMENTS
10mW AT 820-860nm
CLASS 1M LASER PRODUCT
COMPLIES WITH IEC/EN 60825-1
Ed 1 2 2001
COMPLIES WITH 21 CFR 1040 10
AND 1040 11 EXCEPT FOR
DEVIATIONS PERSUANT TO LASER
NOTICE NO. 50.
DATED 26 JULY 2001

4 5
PRODUCT DISPOSAL
This product and its peripheral items
must be taken to a separate collection
point at the product end-of-life. Do not
dispose of these products as unsorted
municipal waste.
WATER-RESISTANCE
Your Reader and accompanying peripheral equipment
are not water-resistant. Keep them dry.
SWITCH ON SAFELY
Do not switch the Reader on where wireless phone
use is prohibited or when it may cause interference or
danger.
SWITCH OFF IN HOSPITALS
Follow any restrictions. Switch the Reader off near
medical equipment.
SWITCH OFF IN AIRCRAFT
Follow any restrictions. Wireless devices can cause
interference in aircraft.
SWITCH OFF WHEN REFUELING
Do not use the Reader and phone at a refueling point.
Do not use near fuel or chemicals.
SWITCH OFF NEAR BLASTING
Follow any restrictions. Do not use the Reader and
phone where blasting is in progress.
QUALIFIED SERVICE
Only qualified personnel may install or repair this
product. For technical support, please refer to the
information on the website: www.bilcaretech.com/
technical_support/index.php. Do not attempt to open
or repair the Reader yourself.
ENHANCEMENTS AND BATTERIES
Use only approved enhancements and batteries. Do not
connect incompatible products.

6 7
4.6 Maintenance of the Reader and battery 38
4.7 General care of your Bilcare nonClonable™
Reader SX21 39
4.8 Bluetooth aspects 41
5 RECHARGING THE BATTERY 42
6 USB DATA TRANSFER 42
7 TROUBLESHOOTING
7.1 Mechanical troubleshooting 42
7.2 Electronic troubleshooting 44
7.3 Swiping troubleshooting 45
7.4 Connectivity and mobile phone
troubleshooting 46
8 TECHNICAL SPECIFICATIONS 49
8.1 Repair work 50
9 WARRANTY 50
10 END USER LICENSE AGREEMENT 51
TABLE OF CONTENTS
1 GENERAL INFORMATION
1.1 Product overview 8
1.2 Terms and abbreviations applied in this
User Manual 9
1.3 Technical support 9
1.4 Manufacturer details 9
2 PRODUCT SUMMARY
2.1 System components 10
2.2 Overview of the System 11
2.3 Overview of the Reader 12
2.4 Overview of the Tag 14
3 GETTING STARTED
3.1 Setting up your mobile phone 15
3.2 Downloading the software onto your
mobile phone 15
3.3 Charging the battery and switching the
Reader on/off 16
3.4 Starting the application 21
4 USING THE READER
4.1 How to swipe the blister pack 26
4.2 Authenticating the blister pack and its
purchase details 31
4.3 System unable to authenticate the blister
pack details 34
4.4 System messages appearing on your
mobile phone 35
4.5 Querying a blister pack that is unable
to verify 38

8 9
1 GENERAL INFORMATION
1.1 Product overview
Counterfeiting has become a serious issue in many
industries including the pharmaceuticals and medical
devices, fashion, software and entertainment media,
consumer electronics, retail, and spare parts sectors.
Counterfeit pharmaceuticals are particularly hazardous
and have led to serious injuries and even fatalities.
The Bilcare nonClonable™ System provides an anti-
counterfeiting solution that gives an indication of
authenticity throughout the supply chain; from
manufacturing to the point of sale.
Combining proprietary tag-based technology with easy-
to-use equipment, this unique groundbreaking solution
provides brand manufacturers with a safe, secure and
highly effective way of authenticating products.
User perspective: brand authentication
The Bilcare nonClonable™ System and the Bilcare
nonClonable™ Reader SX21, herein referred to as the
Reader, have been designed to provide state-of-the-art
anti-counterfeiting protection. In addition, the user can
view the details of the transaction via the Internet, see
www.bilcaretech.com/technical_support/index.php
Brand owner perspective: product track and trace
The Bilcare nonClonable™ System is able to help brand
owners track their product at the time the product is
being authenticated, with the purpose of ensuring that
the sale was legitimate and made in the allotted region
only.
1.2 Terms and abbreviations applied in this
User Manual
Barcode: 12 digit Code 128C barcode
incorporated into the Tag
Fingerprint: Unique micro/nano material
fingerprint contained in each Tag
Reader: Bilcare nonClonable™ Reader SX21
Optical Sensor: Laser-based sensor that reads the
Barcode
Server: Secure server hosting Fingerprints from
all genuine/authorized Tags
Tag: Bilcare nonClonable™ Tag SXM12T
EULA: End User License Agreement
GPRS: General Packet Radio Service
IP: Internet Protocol
LED: Light-Emitting Diode
SIM: Subscriber Identity Module
URL: Uniform Resource Locator
1.3 Technical support
For technical support and other product enquiries
please refer to the Bilcare Technologies website www.
bilcaretech.com/technical_support/index.php.
1.4 Manufacturer details
52, Changi South Street 1
Singapore 486161

10 11
2 PRODUCT SUMMARY
2.1 System components
Please take the time to first familiarize yourself with
the components of the Bilcare nonClonable™ System
product box.
1
3
4
5
6
7
2
8
1. Reader
2. CD
3. USB adaptor
4. Battery
5. USB charger cable (USB to micro USB)
6. User Manual
7. Quick Start Guide
8. Warranty card
2.2 Overview of the System
The Bilcare nonClonable™ System consists of several
integrated components. It is worth acquainting yourself
with the system process so that you understand what
the system is doing when you use it. The following
diagram gives an overview of how the system works.

12 13
1. Blister pack is swiped through the Reader
2. Your mobile phone (not included in this package)
receives the Fingerprint information
3. The Fingerprint information is sent via the Internet to
Bilcare’s remote secure server
4. The Fingerprint information is checked against the
original on the Server database
5. A signal is sent back to your mobile phone indicating
whether a match has been made.
Each transaction is logged and the user can verify
certain transaction details by noting the transaction
number sent to the phone and then logging into the
following website: www.bilcaretech.com/technical_
support/index.php and entering the transaction
number.
2.3 Overview of the Reader
1
3
4
7
2
5
6
1. Red LED
2. Green LED
3. Orange LED
4. Barcode Symbol indicating positioning of Optical
Sensor
5. On/Off button
6. USB charger cable connection
7. Slot for swiping
LED indications
Orange LED
Red LED
Green LED
Solid light – After successful pairing
when the system is ready
for use
Rapid blink – As you swipe the Tag
Slow blink – System ready but not
paired with mobile
phone
Solid light – Starting the system
(glows briefly to be
replaced by slow blinking
green light)
Rapid blink – Failure in reading Tag
Solid light – Charging battery
Rapid blink – Battery fully charged
Slow blink – Low battery indication

14 15
2.4 Overview of the Tag
The Reader is designed to authenticate the Tags
attached to blister packs – an example is shown here.
The Tag contains a special micro/nano Fingerprint,
which is read, together with the Barcode, by the Reader
when the Tag is swiped.
21 3
1. Blister pack
2. Barcode
3. Tag containing the Fingerprint
3. GETTING STARTED
3.1 Setting up your mobile phone
Mobile phone prerequisites:
a) Symbian and Windows Mobile Operating System:
You will need a Symbian phone of the Series 60
S60, 2nd or 3rd edition, or Windows Mobile
6.1. For a comprehensive, up-to-date list of the
mobile phone brands that are compatible with
this mobile phone application, please go to www.
bilcaretech.com/technical_support/index.php.
b) GPRS connectivity: Your mobile phone SIM
card should have GPRS connectivity enabled
for sending information to the Server. If you
wish to check whether you have GPRS correctly
configured, try opening a web browser on your
mobile phone and accessing (for example) www.
google.com. If you do not have GPRS connectivity
you will need to consult with your mobile phone
service provider.
c) Bluetooth: You should be able to pair your mobile
phone with the Reader as described in Section
3.4, provided your mobile phone is also equipped
with Bluetooth capabilities.
3.2 Downloading the software onto your
mobile phone
Before you can start using the Reader, you will need
to transfer the program software onto your mobile
phone. Insert the enclosed CD into your computer disc
drive and transfer the program file (named either .sis
for the Symbian Series 60 second edition or .sisx for the

16 17
Symbian Series 60 third edition) to your mobile phone
using either Bluetooth or a USB. Locate the file on your
mobile phone using file manager. Open the file and it
will automatically install onto your mobile phone. If you
are unsure how to transfer the file, please consult the
user manual for your mobile phone.
3.3 Charging the battery and switching the
Reader on/off
Step 1: Insert the battery provided into the Reader.
Only use the battery provided. For replacement
batteries please contact Bilcare Technologies.
Use of unauthorized batteries may damage the
Reader and will result in the product warranty
being void. Please refer to Figures 1-6 below:
Fig. 1: Ease the backing back in the direction of the
arrow marked on the backing itself, until it clicks - you
do not need to push the backing any further - and
gently lift up from that position. This process is similar
to removing the backing of a mobile phone.
Fig. 2: Remove the battery
by pushing slightly back
towards the connector
and up.
Fig. 3: After charging
the battery (see Step
2 below), replace the
battery by pushing slightly
towards the connector
and down.
Fig. 4: Reader with battery
correctly in place.

18 19
Fig. 5: Ensuring the sides of both the backing and the
main part of the Reader are aligned and that the two
parts are oriented correctly, replace the backing and
gently ease it upwards until it “clicks” back into place.
In Fig. A the backing has been replaced too far down
the Reader and will not close properly. Fig B shows
correct replacement. Push backing upwards from this
position.
Please refer to Troubleshooting in Section 7 of this User
Manual if you are experiencing problems removing or
replacing the backing.
A B
Fig. 6
1
2
1. Slot for swiping
2. USB charger cable in place
Step 2: Using the USB charger provided, charge the
battery for 6 hours for first-time use. If you
charge via your PC or laptop, be aware that
charging times may vary according to your
USB port current. Once you have plugged in
the charger and attached it to the Reader, the
orange LED will light up, indicating that the
battery is charging. Once the orange LED starts
to blink rapidly, the battery is fully charged and
the Reader is ready for use. The orange LED
will light up as soon as the charger is plugged
in, even if the Reader is not switched on. The
Reader must be switched on for you to check

20 21
for a low battery (slow blinking orange LED)
or fully charged battery (rapid blinking orange
LED) For more information on maintenance of
the Reader and battery, see Section 4.6 of this
User Manual.
Step 3: Push the On/Off power button to switch on the
Reader. Once the Reader is on, the red LED will
glow briefly while the Reader self-calibrates.
Do not attempt to swipe a Tag, or interfere
with the Reader’s slot during this period as
it can affect the calibration. Once the Reader
has successfully self-calibrated the red LED
will stop and the green LED will start to flash.
The green LED will continue to flash until the
Reader has successfully paired with your mobile
phone (see 3.4 below).
NOTE: To switch off the Reader, push the On/Off power
button again. All LEDs will go off (unless the Reader is
powered via the USB socket, in which case the orange
LED will continue to glow), indicating that the Reader
has been shut down properly.
3.4 Starting the application
You are now ready to start the application. For this, find
and select the Bilcare nonClonable™ mobile application
on your mobile phone, which is usually found under
“Applications”. Select the icon for the application.
Before you can proceed, the License Agreement screen
will be displayed on your mobile phone.
This is the License Agreement
screen. By selecting “Accept”
you agree to the terms and
conditions given in the End
User License Agreement
(EULA) provided at the end
of this User Manual – see
Section 10.
If you select “Decline” the
program will exit and you
will not be able to use the
application or Reader.
Search for Reader by
selecting “Options”.
License Agreement screen
Welcome screen upon first use

22 23
Selecting “Search” as
shown allows you to search
for Bilcare nonClonable™
Readers on Bluetooth
communication.
This screen will be displayed
on your mobile phone while
it searches for the Reader.
“Options” selection
Reader pairing search display
The list of devices found will
be displayed and selecting
‘Pair’ allows you to proceed.
There will be a brief pause as
the mobile phone completes
the pairing.
If you have not paired with
the Reader before, your
mobile phone will prompt
you to enter the Bluetooth
passcode.
Device pairing list display
Bluetooth passcode request

24 25
The default passcode is
four zeros, i.e.: 0000, which
should be entered as shown.
See also Section 7.4
Connectivity and mobile
phone troubleshooting.
If the mobile phone has
been paired with a Reader
previously – it will show the
name of the previously paired
Reader (in this display it was
paired with Reader SX21-
00001). If you are pairing
with the same Reader, select
“Pair”.
If you are pairing with a
different Reader then select
“Options”. Follow the steps
described in relation to the
“Options” selection, above,
to select and pair with the
new Reader.
Welcome screen upon subsequent use
Your mobile phone will
display this screen once it has
been successfully paired with
the Reader and is ready to
receive data from the Reader.
Ready to use display
4. USING THE READER
4.1 How to swipe the blister pack
Now you can take the blister pack, and swipe it through
the slot in the Reader (as shown in the figure below).
Important note: When swiping the blister pack, take
a firm, central hold of the pack (as shown below) to
ensure you maintain smooth and constant contact
throughout the swiping process. Any jerking or changes
in swiping speed will result in one of the warning
messages listed in Section 4.4. The red LED will also
start to blink rapidly if you have not swiped correctly.
Once the blinking stops you may try to swipe again.

26 27
Any communication error between the Reader and your
mobile phone will cause the red LED to blink rapidly.
If you are experiencing problems with swiping, refer
to Troubleshooting in Section 7 of this User Manual,
or to Section 4.4, which gives all system messages that
appear on your mobile phone.
The figures below show the correct swiping procedure.
Fig. 1: Place the Reader on an even, stable surface such
as a table. Grip the tagged blister pack as shown above.
Making sure that the Barcode is oriented towards the
Barcode Symbol on the Reader, insert the blister pack
into the leading edge of the Reader, as shown above.
Hold the Reader steady with your other hand as you
proceed to swipe. You may swipe in either direction
(either top to bottom or bottom to top), but the blister
pack must be swiped right through the Reader slot.
Fig. 2: Using a steady hand, swipe the blister pack
smoothly through the slot in the Reader. Pull the blister
pack at moderate speed and avoid jerking during the
swipe.
Fig. 2a shows the start
position: Make sure you
insert the outer edge
of the blister pack into
the leading edge of the
slot; that no part of the
pack overlaps with the
sensor area in the middle
of the slot when you
start swiping and that
the barcode is oriented
towards the Barcode
Symbol on the Reader.
Fig. 2b shows the pack
being swiped at an even,
moderate speed through
the slot.
Fig. 2c shows the final
part of the swipe – make
sure that you continue
to swipe the blister pack
all the way through the
Reader slot.
2a
2b
2c

28 29
Fig. 3a: Make sure that you do not bend the blister pack
while swiping. (In all figures the user’s hands have been
removed for clarity.) Here the blister pack is bending
to the left due to lateral
pressure being exerted by
the user during the swipe.
This is incorrect and the
Reader may not be able
to read the Barcode or
the Tag’s micro/nano
Fingerprint – which
could result in a failed
authentication.
Fig. 3b shows a correct
swipe. No lateral pressure
is being exerted on the
blister pack during the
swipe.
Fig. 3c shows a blister
pack bending to the right
due to lateral pressure
being exerted by the user
during the swipe. This is
incorrect and the Reader
may not be able to read
the Barcode or the Tag’s
micro/nano Fingerprint
– which could result in a
failed authentication.
3a
3b
3c
Fig 4: Keep the bottom edge of the blister pack flat in
constant, firm contact with the base of the Reader’s slot
at all times during the swipe. Figure 4 shows a highly
exaggerated tilting of the blister pack during
swiping. The Bilcare nonClonable™ Reader SX21 is a
precision instrument and any tilting or loss of contact
during the swipe may cause the Reader to incorrectly
read the Barcode or the Tag’s micro/nano Fingerprint –
which could result in a failed authentication.
If you are experiencing problems with swiping, please
refer to Troubleshooting in Section 7 of this User
Manual, or to System Messages in Section 4.4.
Once the Reader has successfully read the Tag’s Barcode
number it will send information to the mobile phone it
is paired with and you can move on to verifying the Tag
using the following steps.

30 31
4.2 Authenticating the blister pack and
its purchase details
Reading data
After you have swiped the
blister pack, your mobile
phone will display this screen.
This screen will be displayed
as the data is read and sent
to the Server.
Match found authentication
Reports: transaction details
Once processing is complete
the details will be displayed
on your mobile phone
screen, as exemplified here.
N.B. the screen depicted
here is a generic screen. The
appearance of such screens
will vary according to the
brand and the prerequisites
of the brand owner.
Select “Back” if you would
like to do another swipe.
Comprehensive details
of where and when the
transaction was made. Note
that each signal which has
been sent to the Server is
given a unique Transaction
ID .
Select “Reports” if you would like to view further details
regarding the swipe you have just done.

32 33
Reports: swipe history
Reports: network details
Comprehensive history of the
last three swipes.
The previous three swipe
histories can be viewed by
scrolling the up/down arrows
at the bottom of the screen.
IP details for both the mobile
phone and the Server.
Reports: package details
4.3 System unable to authenticate the blister
pack details
Package details of the
product after matching
including product name,
manufacturer, date of
manufacture, expiry date,
location of manufacture and
Barcode ID.
If the Reader is unable to
authenticate the blister
pack, your mobile phone will
display this message.
If you receive this message
it is advisable to repeat the
swipe. If the Tag still cannot
be authenticated, refer to
Section 4.5.

34 35
4.4 System messages appearing on your
mobile phone
WARNING MESSAGES
Please swipe slower
Your swiping speed is too
fast. Please swipe again more
slowly.
Your swiping speed is too
slow. Please swipe again
faster.
Unrecognized barcode
The system has not been able
to recognize the Barcode.
Your swiping speed may be
incorrect or the Barcode may
be dirty.
• Check Barcode is clean
and swipe again.
• Check your swiping
motion is correct. Refer
to Section 4.1 for correct
swiping technique.
• Check that the blister pack is oriented towards the
Barcode Symbol on the Reader and that it is passing
right through the optical sensor.
• If the problem persists please make sure that the Tag
you are swiping is indeed a Bilcare nonClonable™
Tag. All Bilcare nonClonable™ SXM21T Tags use 12
digit Code 128C barcodes. Please check that the
Barcode has 12 numeric digits printed on it.

36 37
A Bluetooth communication
error has occurred. Try
reconnecting to the Reader
following the steps in Section
3.4.
Your mobile phone is unable
to establish a connection
with the Internet. This may
be because you are in an area
of poor reception (network
coverage). Another possibility
is that the SIM card in your
mobile phone does not have
GPRS connectivity. Contact
your service provider to
upgrade to activate GPRS on
your SIM card, or to obtain
a SIM card that is GPRS-
enabled.
ERROR MESSAGES
Connection with reader lost!
Network communication error!
4.5 Querying a blister pack that is unable to
verify
To report a suspect blister pack, please record the
Transaction ID of the swipe and then go to the
following website: www.bilcaretech.com/technical_
support/index.php for further information on how to
query the transaction.
4.6 Maintenance of the Reader and battery
The Reader is powered by a rechargeable battery.
Please charge the battery for at least 6 hours before
first time use. The full performance of a new battery is
achieved only after two or three complete charge and
discharge cycles.
Unplug the charger from the USB plug and the Reader
when not in use. Do not leave a fully charged battery
connected to a charger, since overcharging may shorten
its lifetime. If left unused, a fully charged battery will
lose its charge over time.
DO’s and DONT’s
• Only use the battery for its intended purpose. Never
use any charger or battery that is damaged.
• Do not short-circuit the battery. Accidental short-
circuiting can occur when a metallic object such as
a coin, clip, or pen causes direct connection of the
positive (+) and negative (-) terminals of the battery
(these look like metal strips on the battery). This
might happen, for example, when you carry a spare
battery in your pocket or purse. Short-circuiting the
terminals may damage the battery or the connecting
object.

38 39
• Leaving the battery in hot or cold places, such as
in a closed car in summer or winter conditions,
will reduce the capacity and lifetime of the battery.
Always try to keep the battery between 15°C and
25°C (59°F and 77°F). A Reader with a hot or cold
battery may not work temporarily, even when the
battery is fully charged. Battery performance is
limited in temperatures well below freezing – do not
use your Reader at temperatures below freezing.
• Do not dispose of batteries in a fire as they may
explode. Batteries may also explode if damaged.
Dispose of batteries according to local regulations.
Please recycle when possible. Do not dispose of as
unsorted municipal waste.
• No water or moisture should enter into the Reader.
The Reader has been designed to operate under
normal room temperature and pressure and should
not be used under extreme temperatures or humidity
conditions – the Readers are designed to be used
between 5°C and 50°C without any moisture
condensation.
4.7 General care of your Bilcare nonClonable™
Reader SX21
You are advised to backup the data/information you
obtained through the use of this Reader as there is a
risk of loss of data when only viewed on the mobile
phone.
The Bilcare nonClonable™ Reader SX21 is a precision
instrument and should be treated with care. The
suggestions below will help you protect your warranty
coverage.
• Keep the Reader dry. Precipitation, humidity, and all
types of liquids or moisture can contain minerals that
will corrode electronic circuits. If your Reader does
get wet, remove the battery, and allow the Reader to
dry completely before replacing it.
• Do not use or store the Reader in dusty or dirty areas.
Its external parts and internal electronic components
can be damaged. In particular always keep the slot
and sensor area of the Reader clean.
• Do not store the Reader in hot areas, i.e. in direct
sunlight. High temperatures can shorten the life of
electronic devices, damage batteries, and warp or
melt certain plastics. Refer to Storage Conditions
under Section 8.
• Do not store the Reader in high humidity. When the
Reader returns to its normal temperature, moisture
can form inside the Reader and damage electronic
circuit boards. Refer to Storage Conditions under
Section 8.
• Do not attempt to open the Reader under any
circumstances.
• Do not drop, knock, or shake the Reader. Rough
handling can break internal circuit boards and fine
mechanics.

40 41
• Do not use harsh chemicals, cleaning solvents, or
strong detergents to clean the Reader.
• Do not paint the Reader. Paint can clog the inner
parts and prevent proper operation.
• Use a soft, clean, dry cloth to clean the Reader,
ensuring that cloth strands are not left on the Reader,
particularly not in the slot area of the Reader, after
cleaning.
4.8 Bluetooth aspects
There may be restrictions on using Bluetooth
technology in some locations. Check with your local
authorities or service provider.
Using Bluetooth technology increases the demand on
battery power. You are advised to switch your Reader
off when it is not in use and to turn off the Bluetooth
on your mobile phone when you are not intending to
use your Reader for extended periods.
All of the above suggestions apply equally to your
Reader, battery, charger, or any enhancement. If any
part of this equipment is not working properly, contact
Bilcare via our website: www.bilcaretech.com/technical_
support/index.php for advice on servicing.
5. RECHARGING THE BATTERY
The swiping process takes up some power from
the battery and you have to recharge the battery
periodically. For this, use the cable provided along with
the Reader. Insert the thin end of the cable into the
Reader and connect the other end with the charger
to a wall socket. See Section 3.3 for more details on
charging the battery. The Reader also supports USB
Charging; you may charge from a laptop or a Personal
Computer by gently detaching the cable from the
charger and plugging this end into the USB slot of the
laptop/PC. You may use the Reader even as charging is
in progress. If you do charge via your PC or laptop, be
aware that charging times may vary according to your
USB port current.
6. USB DATA TRANSFER
Although your Reader has a micro-USB connector it is
not configured to transmit data via USB.
7. TROUBLESHOOTING
7.1 Mechanical Troubleshooting
Problem: I cannot remove/replace the Reader backing.
Solution: Carefully follow in the instructions in Section
3.3 showing how to remove and replace the Reader

42 43
When removing the backing, ease the backing back in
the direction of the arrow marked on the backing itself,
until it “clicks” - you do not need to push the backing
any further - and gently lift up from that position.
Forcing or tugging will potentially damage the Reader.
backing. In the image below, the backing has been
replaced too far down the Reader and will not click
back up into place.
Ensuring the sides of both the backing and the main
part of the Reader are aligned, replace the backing,
as shown above, and gently ease it upwards until it
“clicks” back into place. The two parts will “click” firmly
together and there should be no gaps between the
backing and the main part of Reader.
7.2 Electronic troubleshooting
Problem: My Reader is not powering on.
Solution: Your battery may have been discharged.
Recharge the battery using the charger and cable

44 45
provided with the Bilcare nonClonable™ System.
Refer to Section 3.3 in this User Manual for further
information on charging your Reader battery.
Problem: When the Reader is switched on, the red LED
stays on and is not replaced by a blinking green light.
Solution: The Reader is unable to self-calibrate.
Switch the Reader off, make sure that nothing is in the
Reader slot slot and switch the Reader back on again. If
the problem persists, please refer to Section 1.3 of this
User Manual for technical support information.
7.3 Swiping troubleshooting
Problem: I cannot complete a correct swipe.
Solution: Ensure you are applying the correct swiping
method by referring to the information and images
given both here and in the main swiping Section 4 of
this User Manual.
In the image above, the pack is positioned too far
out of the Reader slot, so that the Tag does not make
smooth, constant contact with the base of the slot. This
can happen if the pack is held too far to the back. Tak-
ing a firm, central grip on the pack, as shown in Section
4.1, facilitates a smooth swiping action.
If the pack is removed too early from the Reader, it
cannot read the Tag properly and you will receive an
error message. To remove the blister pack at the point
depicted above would be too early. The pack must pass
the optical sensor indicated by the Barcode Symbol on
the Reader and pass right through the Reader slot.
Please also remember that the Tag must be correctly
oriented. The Barcode Symbol on the Reader indicates
the placement of the optical sensor, which reads the
Tag. The Barcode on the blister pack must face towards
the Barcode Symbol and pass through the optical
sensor for a successful swipe.
7.4 Connectivity and mobile phone
troubleshooting
Problem: The Reader is not detected by the mobile
phone for Bluetooth pairing.

46 47
Solution: Please make sure of the following: a) that the
Reader is switched on and the green LED is blinking,
b) that your mobile phone’s Bluetooth is switched on
(ensure that the Reader is within a 5 meter radius of the
mobile phone).
Once both the Reader and mobile phone are switched
on, pair them via Bluetooth using the steps outlined
in Section 3.4. You can also refer to the information
provided in Section 4.8. If you are still experiencing
problems, try following the steps below:
Step 1: Go to the Bluetooth options in your mobile
phone and make sure that your phone’s
Bluetooth is turned on. (Refer to your mobile
phone user manual to activate Bluetooth
connectivity).
Step 2: Now search for the Bluetooth devices in the
vicinity. The Bilcare nonClonable™ Reader will
come up as one of the devices detected. If the
Reader does not appear, make sure a) that the
Reader is on with the green LED flashing, b)
that the mobile phone’s Bluetooth is turned on
and c) that the Reader and mobile phone are in
close proximity.
Step 3: Choose the option to pair the Reader with your
mobile phone. The Bluetooth application will
ask you to enter the passcode. The default
passcode is four zeros, i.e.: 0000. Key in the
passcode and the Reader will be paired with
the mobile phone through Bluetooth. See the
following screen display.
Problem: The message “Sending data” or “Receiving
data” is displayed on the mobile phone for a long
duration and the transaction details do not come up.
Solution: This is most probably due to poor GPRS
connectivity. Contact your service provider for GPRS
settings.
Problem: The application on the mobile phone does
not start.
Solution: This could be due to multiple applications
running on the mobile phone. Consult your
mobile phone user manual to terminate unwanted
applications. The application may be corrupted. Please
refer to Section 1.3 of this User Manual for technical
support information.

48 49
Problem: The message “Please swipe Tag” does not
appear on the mobile phone.
Solution: This happens if the Reader is switched off
or if it has exited the 5 meter radius of the mobile
phone. Exit the application and verify that the Reader
is accessible to the mobile by following the steps in
Sections 3.4 and 4.8.
8. TECHNICAL SPECIFICATIONS
Bilcare Technologies strives to constantly improve its
products and services, therefore the specifications of
components within the Bilcare nonClonable™ System
may differ from those provided in this User Manual.
Details of new specifications and component numbers
are available on the Bilcare website: www.bilcaretech.
com/technical_support/index.php.
Reader model SX21
Dimensions 100 mm x 66 mm x 19 mm
Operating Voltage 3.7V
Battery capacity 1500 mAh
Battery type
Reader is powered by a custom
Lithium-Ion battery
Communication Bluetooth
Charger cable
Micro USB cable to charge the
Reader
Operating Conditions
• Temperature: Min: 5oC, Max 50oC
Relative Humidity: No-condensation
Storage Conditions
Please discharge the battery fully prior to storage.
• Less than 1 month duration
Temperature: Min: -20oC, Max 60oC
Relative Humidity: 20% to 90% relative humidity,
no-condensation
• Less than 3 months’ duration
no-condensation
• Less than 12 months’ duration
no-condensation
8.1 Repair work
Only personnel authorized by Bilcare should repair
the Reader. For technical support and other product
enquiries please refer to the Bilcare Technologies
website www.bilcaretech.com/technical_support/index.
php.
9. WARRANTY
The warranty period for the Bilcare nonClonable™
Reader SX21 is 1 year from the date of purchase. The

50 51
10. END USER LICENSE AGREEMENT
10.1 This End-User License Agreement (“EULA”) is a legal
agreement between Bilcare Technologies Singapore Pte
Ltd (“The Supplier”), the Purchaser and, where applicable,
You (“The User”). It outlines the terms and conditions for
the use of the Supplier’s Software Product(s) related to the
Bilcare nonClonable™ Reader SX21 (including firmware,
software, associated media, printed materials, and “online”
or electronic documentation, the “Software Product”).
By installing, copying, accessing or otherwise using the
Software Product the Purchaser agrees to be bound by the
terms of this EULA.
10.2 If You are an individual who is accessing or otherwise using
this Software Product, You agree that You are authorized
by the Purchaser to do so and act on the behalf of the
Purchaser, thus You agree to use this Software Product
in accordance with all the terms and conditions set forth
warranty period for all peripheral items accompanying
the Reader, including the battery, is 6 months from
the date of purchase. Both are subject to the Terms
and Conditions as laid out in the enclosed Warranty
Certificate. Please fill in the purchase details as required
on both parts of the Warranty Certificate and mail to
Bilcare Technologies at:
Bilcare nonClonable™ Reader SX21 Warranty
52, Changi South Street 1
Singapore 486161
in this EULA. You further agree that You are bound by all
the Terms and Conditions set forth and applicable to the
Purchaser.
10.3 The Software Product is protected by copyright laws and
international copyright treaties, as well as other intellectual
property laws and treaties to the extent permitted by
applicable law. All title and copyrights in and to the
Software Product (including but not limited to any images,
photographs, animations, video, audio, music, text, and
“applets” incorporated into the Software Product) are
owned by the Supplier or its suppliers and / or licensors.
10.4 The Software Product is licensed, not sold. Subject to the
condition that the Purchaser is in compliance with the
terms of this EULA: (a) the Purchaser may install and use
one copy of the Software Product, or any prior version for
the same operating system, on a single computer and/
or on a single mobile phone (depending on the version of
the software supplied), for use by a single simultaneous
operator. No other use, copying or distribution of the
Software Product is permitted. The Purchaser shall not rent
the Software Product, nor offer use of it to others through
a service bureau or application service provider. The EULA
of an upgrade, update, patch or enhancement of a prior
release of the same Software Product which was installed
on the same computer, supersedes the rights under a prior
license agreement for the Software Product.
10.5 Except to the extent such a restriction is unenforceable
under local law, the Purchaser shall not reverse engineer,
decompile, or disassemble the Software Product. The
Software Product is licensed as a single product, and its
component parts shall not be separated for use on more
than one computer, mobile phone or other platform. The
Purchaser shall not modify, amend, or create derivative
works of the Software Product.
10.6 The license granted under this EULA commences upon
the installation of the Software Product and is effective in

52 53
perpetuity unless terminated per the terms of this EULA.
10.7 Without prejudice to any other rights, the Supplier may
terminate this EULA or the Purchaser’s rights under this
EULA at any time if the Purchaser fails to comply with the
terms and conditions of this EULA. Upon termination of the
Purchaser’s rights under this EULA for any reason, or upon
termination of the EULA itself, the Purchaser must destroy
all copies of the Software Product and all of its component
parts in its possession (including all component parts,
the media and printed materials, any prior versions, and
this EULA). The terms of this paragraph shall survive any
termination of this EULA.
10.8 The Purchaser shall not transfer any or all of its rights under
this EULA without prior written agreement of the Supplier,
except for the case outlined in 10.2 where an authorized
user is using the Software Product in compliance with this
EULA.
10.9 To the extent that any third party’s intellectual property is
incorporated within the Software Product, the Purchaser
agrees that such third party is a third-party beneficiary of
the terms of this EULA to the extent of the third party’s
license to the Supplier.
10.10 The Purchaser may make a single back-up copy of the
Software Product, provided it is used solely for archival
purposes to enable reinstallation of the Software Product
should the licensed version become damaged, corrupted or
deleted.
10.11 All warranties relating to or in connection with the Software
Product (hereinafter called the “Warranty”) are described
exhaustively in and are contained solely in this Clause as
follows: Software Products have been carefully written and
compiled, but the Supplier makes no warranty express or
implied that the software is free of bugs or minor defects
that may arise during use. The Purchaser is responsible
for backing-up files and data regularly. Where software
contains bugs that materially affect its functionality, the
Supplier will make reasonable efforts to fix the bugs in a
timely manner and shall rectify defects and / or provide fixes
/ patches / updates to rectify such defects. The rectification
of such defects shall require that the effects of the defect
be reproducible and have been sufficiently described by the
Purchaser to effect the rectification. The Purchaser may, at
the discretion of the Supplier, be responsible for installing
said fixes / patches / updates following the instructions
provided by the Supplier. The foregoing Warranty is always
limited to the item cost of the respective Software Product
at fault. Where the Software Product forms part of a brand
security system, in no circumstances is the Supplier liable
for the cost and/or value of the item labelled or tagged,
and/or for any direct, indirect, incidental, consequential,
special, exemplary, economic, punitive damages whether
or not arising out of or relating to the use of the Software
Product. THE FOREGOING WARRANTY IS EXCLUSIVE AND
EXHAUSTIVE AND IN LIEU OF ALL OTHER WARRANTIES
WHETHER WRITTEN, ORAL, OR IMPLIED AND SHALL BE
THE PURCHASER’S SOLE REMEDY AND THE SUPPLIER’S
SOLE LIABILITY ON CONTRACT OR WARRANTY OR TORT
(INCLUDING NEGLIGENCE) OR OTHERWISE FOR ALL OR
ANY OF THE SOFTWARE PRODUCTS. THE SUPPLIER MAKES
NO WARRANTY AS TO THE VALIDITY OR SCOPE OF THE
COPYRIGHT OR PATENTS UNDERLYING OR RELATING TO THE
SOFTWARE PRODUCTS OR THAT THE SOFTWARE PRODUCTS
WILL BE FREE FROM INFRINGEMENT ON COPYRIGHT OR
PATENTS OR OTHER INTELLECTUAL PROPERTY RIGHTS OF
THIRD PARTIES.
10.12 The Supplier shall not be liable in contract or in tort
(including negligence or strict liability) or otherwise for
loss of profits or revenue, costs associated with business
interruption, loss of use of equipment or plant, cost of
capital, cost of purchased or replacement equipment, loss
of data, breach of security protocols or data encryption
methods, claims of customers of the Purchaser, or for

54 55
any special, indirect, incidental or consequential damages
including, but not limited to, injury or loss of life. The
remedies of the Purchaser set forth in this EULA are
exclusive and exhaustive and the total liability of the
Supplier in connection with, arising out of, and/or in
relation to the Software Product shall not exceed the price
of the Software Product on which such liability is based.
10.13 Data services, hardware information, software information,
network information, authentication information,
verification information, transaction codes, and verification
of Tags/labels/objects (“Authentication Information”) that
the Software Product may process, present, display, report,
infer or store are provided on an “as is” basis and only as
an indication and no assurance or guarantee of validity or
correctness is made or implied by the Supplier.
10.14 The User and The Purchaser agree to “Authentication
Information” being transmitted to the Supplier by the
network service selected either by default or by choice, and
for the information to be processed by The Supplier and
The Purchaser. The User and The Purchaser understand and
agree that the “Authentication Information” may include
the unique identity of hardware, the phone number of the
mobile phone number / SIM card in use, the IP address of
the hardware, the name of the service provider, the location
of the hardware and details of the Tag/label being read, and
that it is necessary to do so to provide the brand security
service offered through the use of the Software Product.
The User and The Purchaser understand and agree that
the data associated with the use and transactions of the
Software Product may be stored in an electronic database
by the Supplier and/or the Purchaser for future analysis and
reporting purposes. The User permits that the Supplier may
use the “Authentication Information” to contact the User or
the Purchaser in relation to the provision, enhancement or
quality control of the Software Product of the services that
are being supplied to the Purchaser.
10.15 In no event, whether as a result of breach of contract, tort
(including negligence) or otherwise, shall the Supplier have
any liability whatsoever to any third party for any damages
whether direct, indirect, special, incidental, consequential
or otherwise.
10.16 The Purchaser shall indemnify and hold harmless the
Supplier fully and effectively against any losses, costs,
damages, claims, demands, actions, proceedings, liabilities
and expenses to which the Supplier may become subject
made by any third party or otherwise:
(a) whether as result of breach of contract, tort (including
negligence) or otherwise; and/or
(b) arising out of, in connection with, and/or related to the
use of the Authentication Information and/or Software
Product.
10.17 The Purchaser agrees and acknowledges that it is
reasonable and fair that the business interests of the
Supplier are protected by way of the various provisions
herein and throughout this EULA which limit the quantum,
scope and/or extent of the liability or potential liability to
the Purchaser and/or third parties.
10.18 The terms and conditions set out in this EULA shall be
subject to, governed by, and interpreted in accordance with
the laws of the Republic of Singapore. The United Nations
Convention On Contracts for the International Sale of
Goods (Vienna, 1980) shall not apply to the Contract and is
hereby expressly excluded.
10.19 All disputes, claims or proceedings between the Supplier
and the Purchaser relating to the validity, construction
or performance of the EULA shall be resolved, at the
election of the Supplier, either by court proceedings, or by
reference to arbitration in Singapore in accordance with
the Arbitration Rules in Singapore International Arbitration
Centre (“SIAC Rules”). Judgment upon the award rendered
by the arbitrator may be entered in any court having
jurisdiction over the parties or application may be made to

56
any such court for a judicial acceptance of the award and
an order for enforcement, as the case may be.
10.20 This EULA is the entire agreement between the Supplier
and the Purchaser relating to the Software Products and
they supersede all prior or contemporaneous oral or
written communications, proposals and representations
with respect to the Software Products or any other subject
matter covered by this EULA. If any provision of this EULA is
held to be void, invalid, unenforceable or illegal, the other
provisions shall continue in full force and effect.
10.21 If the Purchaser does not agree to the terms of this EULA,
the Purchaser shall not use or copy the Software Product,
and the Purchaser should promptly contact the Supplier for
instructions on return of the unused product(s) for a refund
in accordance with Supplier’s return policies.
10.22 For product support and contact details of the Supplier,
please refer to the Delivery Note that accompanied the
delivery of the Software Product or use contact information
provided in accompanying documentation.

nonClonableID™ Reader SX21 User Manual

More Related Content

What's hot (20)

Viewers also liked (16)

Similar to nonClonableID™ Reader SX21 User Manual (20)

More from Bilcareltd (20)

Recently uploaded (20)

nonClonableID™ Reader SX21 User Manual