NorthStar NSB Technical Application Manual

To help us better serve you, please visit our web site at
www.northstarbattery.com/survey and complete our Customer Survey.
We value and appreciate your input
NorthStar Battery (NSB)
Telecom Application Manual
Form: SES-544-01-15 Issued: 11-13-15 ECO-100786

2
Definitions
The definition for each of the following terms or abbre-
viations describes the context employed throughout this
document.
Monobloc* A discrete unit of one (1) or more
2-V cells
Battery* A unit or module consisting of one
(1) or more monoblocs
VPC Volts per cell
Electrolyte Sulfuric acid diluted with de
ionized water and mixed with
sodium sulfate
* Terms may be used interchangeably given the circumstance.
1 - Introduction
1.1 The Silver Star Technology®
and
Semi-Stable Mains
Silver Star Technology®
batteries are designed to operate
in applications where the mains AC is stable or semi-sta-
ble, i.e., where interruptions to power occur less than 10
hours per week. The batteries have been formulated with
a unique combination of grid alloy and active materials
that allows the technology to be fully recharged quickly at
normal float voltages. Furthermore, outages are relatively
rare. This means that the batteries can be fully recharged
following an outage, which is important for maximizing
cyclic performance.
The Silver Star Technology®
has also been designed to
provide a high energy density. Not only does this allow
for maximum backup times, but it also minimizes the
monobloc footprint and reduces floor loadings. Finally,
the high compression design and advanced active
material formulations provide class-leading cycle life
under stable or semi-stable mains conditions.
1.2 Discharge Rate
In this document, the charge and discharge rates
(amps) are expressed as multiples of I10, where I10 is
the current for a 10-hour discharge to 100% depth-of-
discharge (DOD). These values serve to normalize data
across a range of monobloc sizes. Consider the following
example:
10-h discharge capacity NSB 100FT = 100 Ah (EODV =
1.80 VPC @ 25°C).
1 x I10 = 1 x (10-h discharge current)
1 x I10(NSB 100FT) = 1 x 10A = 10 A
2 x I10(NSB 100FT) = 2 x 10A = 20 A
2 - Charge
In order to maximize the life of the Silver Star
Technology®
, it is recommended that the monobloc be
fully recharged following an outage.
SILVER STAR TECHNOLOGY®
www.northstarbattery.com Form: SES-544-01-15 Issued: 11-13-15 ECO-100786

3
2.1 Determining State of Charge (SOC)
The SOC of a monobloc can be determined by measuring
the open-circuit-voltage (OCV) of the monobloc. If the
monobloc has been recently recharged, a rest period of
at least 3 hours after completion of recharge is required
before taking measurements. The relationship between
OCV and SOC for the Silver Star Technology®
is
displayed in the following graph:
A fully charged Silver Star Technology®
battery Open
Circuit Voltage will measure approximately 13.0 V.
2.2 Thermal Compensation
The optimum level for float charging the Silver Star
Technology®
is 2.27 VPC at +25°C (+77°F). If the
monobloc temperature increases above this level, a
thermal compensation of -4 mV/cell/°C is required for
safe operation and achieving optimal life. Conversely,
if the temperature decreases below 25°C, the voltage
should be increased by 4 mV/cell/°C. Most modern
charge rectifiers have integrated temperature monitoring
and voltage regulation which should be used in any
environment where temperature is not precisely
controlled. The graph below shows values for an
individual cell.
2.3 Fast Charging
If the charging system is properly sized, a fast charging
regime will serve to minimize the time needed to recharge
Silver Star Technology®
batteries. This can be beneficial,
for maximizing the cycle life of the product.
In a fast charging regime, the charging system is
assumed to be adequately sized to provide the power
needed (see Section 2.4). Charge voltage is increased
which results in increased charge current. This in turn
causes a discharged monobloc bank to fully recharge in a
shorter time.
The increased voltage setting is known as boost voltage.
In a fast charging regime the boost voltage shall be 2.41
VPC provided that the temperature is a nominal +25°C
(+77°F). The following graph shows the recommended
charging profile following a 100% DOD cycle:
The table above shows the time needed to recharge
following a 100% DOD cycle, depending on the maximum
charge current available. If the DOD is less than
100%, the total recharge time will be less. To prevent
overcharge, the duration from T1 to T2 (i.e. the time at
2.41 VPC) should always be limited to 4 hours, and then
the rectifier voltage returned to the recommended float
voltage.
If the monobloc temperature increases above +25°C
(+77°F), a thermal compensation of -4 mV/cell/°C to
boost voltage is recommended. Conversely, if the
temperature decreases below

4
www.northstarbattery.com
25°C, the boost voltage should be increased by 4 mV/
cell/°C. The graph below shows values for an individual
cell:
2.4 Recharge Power
Depending on the charging system, recharge times
can vary greatly following an outage. If the recharge
power is relatively low, it will take longer to fully recharge
a monobloc. It is recommended to provide a regular
overcharge factor of between 103% and 106% SOC after
a discharge.
The following chart shows the time required to fully
recharge an NSB Silver Star Technology™ battery from a
complete 100% DOD discharge, as a function of rectifier
voltage and available current.
3 - Discharge
3.1 Storage and Self-Discharge
During storage, lead-acid monoblocs will gradually self-
discharge. It is recommended that monobloc SOC be
maintained above 50% at all
times in order to avoid irreversible capacity loss. The rate
of self-discharge increases with increasing temperature.
For example, a monobloc at 25°C will drop from 90%
to 60% in 15 months, whereas the same monobloc at
40 °C will take just 6 months. As a result, maintenance
charging needs to be performed more frequently at higher
temperatures.
3.2 End of Discharge Voltage (EODV)
In the event of a deep discharge, a recommended
minimum end-of-discharge voltage (EODV) should be
used to avoid over discharge. A value of 1.80 VPC is
common, but this value should be adjusted based on the
discharge rate. The following table provides a guide for
EODVs at various discharge rates.
Discharge Rate (Hours) EODV (VPC)
20 1.85
10 1.80
5 1.75
1 1.70
EODV can be controlled using a Low Voltage Disconnect
(LVD) as part of the load circuit.
3.3 Cold Temperature Performance
Colder temperatures can prolong monobloc life because
corrosion processes within the positive plates of the
monobloc slow down as the temperature decreases.
Unfortunately, lower temperatures also lower the capacity
of lead-acid monoblocs. As monobloc temperature drops
below the recommended operating
Maximum tolerance of 0.02 VPC
Minimum tolerance of 0.02 VPC
Nominal

5
temperature of +25° C (+77°F), the monobloc capacity
decreases according to the following chart:
4 - Useful Life
4.1 Shelf Life
NSB Silver Star Technology®
batteries may be stored
for up to 2 years, provided that the SOC is maintained
above 50%. Failure to provide the required maintenance
charging (see Section 3.1) may lead to irreversible
capacity loss.
4.2 Float Life vs. Temperature
Lead-acid monoblocs operating under float in semi-
stable mains applications are being charged most of
the time. As a result, the lead grids within the positive
plates undergo slow corrosion, which is a normal aging
mechanism under float duty. The rate of this process
increases with increasing temperature and, as a result,
the temperature of monoblocs has a large affect on
their float life. For each increase of 10°C, float life will
decrease by a half. For example, if the temperature rises
from the recommended operating temperature of +25°C,
to +45°C, the expected life of the monobloc will decrease
from 10 to 2.5 years (see chart below).
Under float duty, a monobloc is considered to have
reached its end of life (EOL) when it can no longer deliver
80% of its original rated capacity. For example, a 100 Ah
monobloc has reached EOL when its discharge capacity
has dropped below 80 Ah. The relationship between
capacity loss during float duty and monobloc temperature
is shown in the following chart.
4.3 Cycle Life vs. Depth of Discharge
One factor which influences the cycle life of a monobloc
is the depth-of-discharge (DOD). DOD is expressed as a
percentage of rated capacity delivered during discharge.
For example, if a 100 Ah battery delivers 10 Ah, the DOD
would be 10%. As the DOD per cycle increases, the
cycle life of the monobloc will decrease. The following
chart can be used to estimate the cycle life of a Silver
Star Technology®
battery if the DOD per cycle is known.

6
5 - Introduction
Blue Star Technology®
batteries (Blue batteries) are de-
signed to operate in regions with unstable mains.
5.1 Unstable Mains
If the main AC power is routinely unavailable, it can be
considered unstable. Outages can last for a few sec-
onds or for many hours, the length and frequency of the
outage limits the recharge time for the monobloc. In these
applications, the monoblocs frequently cycle in an under-
charged state.
During these outages, depending on monobloc size, the
monobloc may never be fully discharged. Furthermore,
even if power is restored, it may not be available long
enough to return the monoblocs to 100% State of Charge
(SOC). This situation is known as uncontrolled Partial
State of Charge (uPSOC) cycling.
5.2 Uncontrolled Partial State of Charge (uPSOC)
Cycling
In a uPSOC cycle, the monobloc is partially discharged
but may only experience a full recharge when the condi-
tions allow, which may be very infrequent. The following
chart shows
data collected from the field in an unstable mains
application:
As may be seen from the above chart the monobloc
operates between ~90% to ~50% SOC for the first 4-days
and only receives a full charge on the 5th day.
5.3 uPSOC Cycling: Blue Star Technology®
vs. Standard AGM
The main advantage of Blue batteries is their ability
to operate under uPSOC conditions without having to
be fully recharged every cycle. Blue batteries have a
modified electrochemistry allowing them the ability to
repeatedly operate at a low SOC. Consequently the Blue
batteries can be expected to perform many more uPSOC
cycles than a standard AGM monobloc.
The following figure provides a comparison of cyclic
performance of Blue Star Technology™ batteries
compared to standard AGM
BLUE STAR TECHNOLOGY®

7
technology. Both technologies were cycled in a
controlled lab test designed to simulate an unstable
mains condition.
Clearly the Blue product is far better suited to these
arduous conditions than the standard AGM, returning 6
times the cycle life.
5.4 PSOC Window vs. Useful Life
One method of estimating monobloc life in a uPSOC
application is to consider the average PSOC window. The
PSOC window is defined as the difference in SOC from
the recharged to the discharged state. For example, in
a PSOC cycle the monobloc may be recharged to 90%
SOC and subsequently discharged to 60% SOC. The
PSOC window is therefore 30%.
Unfortunately in a real uPSOC application it is difficult
to estimate the PSOC window or even the frequency of
outages, but a simplistic estimation may be gained by
analysis of the AC grid stability.
If the PSOC window and the average number of PSOC
cycles per day are known, the monobloc life may be
estimated from the following figure. For example, if the
monobloc is sized to deliver 20% PSOC window per cycle
and it experiences 3 cycles per day then an estimated 3
years life may be anticipated.
5.5 Discharge Rate
In this document, the charge and discharge rates
(amps) are expressed as multiples of I10, where I10 is
the current for a 10-hour discharge to 100% depth-of-
discharge (DOD). These values serve to normalize data
across a range of monobloc sizes. Consider the following
example:
10-h discharge capacity NSB 170 Blue = 141Ah
(EODV = 1.8VPC @ 25°C)
1xI10 = 1 x (10hr discharge current)
1xI10(NSB 170 Blue) = 1 x 14.1A = 14.1A
2xI10(NSB 170 Blue) = 2 x 14.2A = 28.2A
6 - Charge
the Open Circuit Voltage (OCV) of the monobloc. If the
OCV and SOC for the Blue batteries is displayed in the
following graph:

8
A fully charged Blue battery OCV will measure
approximately 12.7 Volts.
6.2 Thermal Compensation
The optimum float charging voltage for the Blue Star
Technology®
is 2.27 VPC at +25°C (+77°F). If the
monobloc temperature increases above this level, a
thermal compensation of -2 mV/Cell/°C is required for
safe operation and achieving optimal life. Conversely,
if the temperature decreases below 25°C, the voltage
should be increased by 2 mV/cell/°C. Most modern
charge rectifiers have integrated temperature monitoring
and voltage regulation which should be used in any
environment where temperature is not precisely
controlled. The graph below shows values for an
individual cell.
6.3 Fast Charging
Blue batteries are designed for uPSOC under standard
float conditions. However, in very unstable mains
applications, if the rectifier voltage can be increased, this
may help to maintain the standby autonomy by moving
the uPSOC window to a higher state of charge.
6.4 Recharge Power
Depending on the charging system, recharge times can
vary greatly following an outage. If the recharge power is
relatively low, it will take longer to recharge a monobloc to
100% SOC from a full discharge.
The following chart shows the time required to fully
recharge an NSB Blue battery from a complete
discharge, as a function of rectifier voltage and available
current.
6.5 Recharge Time
The recharge time can also be estimated from the
following formulas:
PSOC Recharge time with 100% charge return =
Capacity * V * %DOD / Recharge Power (W)
Or
Capacity * %DOD / Current (A)
Example: 2 hour discharge on 10 hr monobloc bank
(20% DOD) with 20% to charge the monobloc (1 hour
recharge).
Example: 400Ah monobloc bank with same discharge
and recharged with 3.8 kW (1 hour recharge)
7 - Discharge
During storage, lead-acid monoblocs will gradually
self-discharge. It is recommended that monobloc SOC
be maintained above 50% at all times in order to avoid
irreversible capacity loss. The rate of self-discharge
increases with increasing temperature. For example,
a monobloc at 25°C will drop from 90% to 60% in 15
months, whereas the same monobloc at 40 °C will take
just 6 months. As a result, maintenance charging needs
to be performed more frequently at higher temperatures

9
7.2 End of Discharge Voltage (EODV)
In most applications Blue batteries never go to a
completely discharged state due to their uPSOC
operation. However, in the event of a deep discharge, a
recommended minimum EODV should be used to avoid
over discharge. 1.80 VPC is common, but this value
should be adjusted based on discharge rate.
Discharge Rate (Hours) EODV (VPC)
20 1.85
10 1.80
5 1.75
1 1.70
EODV can be controlled using a Low Voltage Disconnect
(LVD) as part of the load circuit.
7.3 Cold Temperature Performance
Colder temperatures can prolong monobloc life because
corrosion processes within the positive plates of the
monobloc slow down as the temperature decreases.
Unfortunately, lower temperatures also lower the capacity
of lead-acid monoblocs. As monobloc temperature drops
below the recommended operating temperature of +25°
C (+77°F), the monobloc capacity decreases according to
the following chart:
8 - Useful Life
8.1 Shelf Life
NSB Blue batteries may be stored for up to 2 years,
provided that the SOC is maintained above 50%. Failure
to provide the required maintenance charging (see
Section 3.1) may lead to irreversible capacity loss.
8.2 Float Life vs. Temperature
The operating temperature of monoblocs can have
a large affect on their float life. For each increase of
10°C, float life will decrease by a half. For example, if
the temperature rises from the recommended operating
temperature of +25°C to +45°C, the expected life of the
monobloc will decrease from 7 to 2 years.

10
One factor which influences the cycle life of a monobloc
is the depth-of-discharge (DOD). DOD is expressed as a
percentage of rated capacity delivered during discharge.
For example, if a 100 Ah monobloc delivers 10 Ah, the
DOD would be 10%. As the DOD per cycle increases,
the cycle life of the monobloc will decrease. The
following chart can be used to estimate the cycle life of a
Blue battery if the DOD per cycle is known.

11
9 - Introduction
Blue+ batteries are designed to operate in regions with
unstable mains while maintaining higher volumetric ener-
gy density than standard Blue. Except as noted below, all
the information contained in the “Blue Star Technology”
section also applies to Blue+.
10 - Charge
the Open Circuit Voltage (OCV) of the monobloc. If the
OCV and SOC for the Blue+ batteries is displayed in the
following graph:
A fully charged Blue+ battery OCV will measure
approximately 13.0 Volts.
11 - Discharge
During storage, lead-acid monoblocs will gradually
self-discharge. It is recommended that monobloc SOC
be maintained above 50% at all times in order to avoid
irreversible capacity loss. The rate of self-discharge
increases with increasing temperature. For example,
a monobloc at 25°C will drop from 90% to 60% in 15
months, whereas the same monobloc at 40 °C will take
just 6 months. As a result maintenance charging needs
to be performed more frequently at higher temperatures.
BLUE+

12
12 - Useful Life
Blue+ batteries are designed to be able to operate in
highly cyclic applications as well as PSOC applications.
The cycle life versus DOD can be expected to be the
same as mentioned for Blue batteries during standard
cyclic operation. However, during optimal charging
regime the Blue+ batteries can be expected to achieve
cycle life according to the chart below.
100
1,000
10,000
100,000
0% 10% 20% 30% 40% 50% 60% 70%
Cycles
Depth of Discharge
Cycle life vs. DOD
NortStar optimal charging conditions

13
17 - Technical Specifications
For detailed technical specifications, please refer to the
Product Data Sheet.
18 - Contact
www.northstarbattery.com
NorthStar Europe
SiteTel Sweden AB
Staffans Väg 6
SE-192 07 Sollentuna,
Stockholm, Sweden
europe@northstarbattery.com
Tel: +46 8 410 102 00
Fax: +46 8 638 06 00
NorthStar Americas
NorthStar Battery Company LLC
4000 Continental Way
Springfield, MO, 65803,
United States of America
info@northstarbattery.com
Tel: +1 417 575 8200
Fax: +1 417 575 8250
NorthStar Middle East, Africa
SiteTel Sweden AB JTL Branch
Office 702, Saba 1 Tower
Jumeirah Lake Towers, Dubai Uni-
ted Arab Emirates
mea@northstarbattery.com
Tel: +971 4 423 8060
Fax: +971 4 423 8061
NorthStar in Asia-Pacific
NS Asia Pacific Sdn. Bhd.
B2-3A-13A, Solaris Dutamas
No. 1, Jalan Dutamas 1, 50480
Kuala Lumpur, Malaysia
asia@northstarbattery.com
Tel: +60 3 6419 0711

NorthStar NSB Technical Application Manual

More Related Content

What's hot (20)

Similar to NorthStar NSB Technical Application Manual (20)

Recently uploaded (9)

NorthStar NSB Technical Application Manual