Notes1
Download as DOC, PDF0 likes265 views
The document discusses several topics related to lighting and electricity including: - Switchgear, which refers to the switching and protective devices used in high voltage electrical power systems. This includes circuit breakers that can sense faults and interrupt current to isolate issues. - Transformers, which transfer energy between circuits through electromagnetic induction. Power transformers are used for transmission at high voltages while distribution transformers operate at lower voltages for industrial and domestic use. - The properties of visible light including its wavelength spectrum and speed. Light behaves as both a wave and particle. - Newton's experiments with prisms that demonstrated white light is a mixture of colors and prisms separate colors by refracting them by different amounts. - Laws
Notes1
- 1. Switchgear We all familiar with low voltage switches and re-wirable fuses in our home. The switch is used to manually open and close the electrical circuit in our home and electrical fuse is used to protect our household electrical circuit from over current and short circuit faults. In same way every electrical circuit including high voltage electrical power system needs switching and protective devices. But in high voltage and extra high voltage system, this switching and protective scheme becomes complicated one for high fault current interruption in safe and secure way. In addition to that from commercial point of view every electrical power system needs measuring, control and regulating arrangement. Collectively the whole system is called Switchgear and Protection of power system. Switchgear protection plays a vital role in modern power system network, right from generation through transmission to distribution end. The current interruption device or switching device is called circuit breaker in Switchgear protection system. The circuit breaker can be operated manually as when required and it is also operated during over current and short circuit or any other faults in the system by sensing the abnormality of system. The circuit breaker senses the faulty condition of system through protection relay and this relay is again actuated by faulty signal normally comes from current transformer or voltage transformer. A switchgear has to perform the function of carrying, making and breaking the normal load current like a switch and it has to perform the function of clearing the fault in addition to that it also has provision of metering and regulating the various parameters of electrical power system. Electric switchgear is necessary at every switching point in the electrical power system. There are various voltage levels and hence various fault levels between the generating stations and load centres. Therefore various types of switchgear assembly are required depending upon different voltage levels of the system. Besides the power system network, electrical switchgear is also required in industrial works, industrial projects, domestic and commercial buildings. Transformer A transformer is a static electrical device that transfers energy from one circuit to other by inductive coupling between its winding circuits. A varying current in the primary winding creates a varying magnetic flux in the transformer's core and thus a varying magnetic flux through the secondary winding. This varying magnetic flux induces a varying electromotive force (emf) or voltage in the secondary winding based on faraday’s law of electromagnetic induction. Transformers are frequently used to create higher or lower voltages, but they also used to isolate circuits from each other. Power transformer is used for the transmission purpose at heavy load, high voltage greater than 33 KV & 100% efficiency. It also having a big in size as compare to distribution transformer, it used in generating station and Transmission substation .high insulation level.
- 2. The distribution transformer is used for the distribution of electrical energy at low voltage as less than 33KV in industrial purpose and 440v-220v in domestic purpose. It work at low efficiency at 50-70%, small size, easy in installation, having low magnetic losses & it is not always fully loaded. Although commercial electric companies use a large number of transformers throughout their power distribution system, that industry pretty much reserves the name "distribution transformer" for the final transformer in the system before the electricity enters a residence or a business. Various types of distribution transformers serve different needs according to amount of power needed as well as physical and environmental considerations. ILLUMINATION Visible light (commonly referred to simply as light) is electromagnetic radiation that is visible to the human eye, and is responsible for the sense of sight. Visible light has a wavelength in the range of about 380 nanometres (nm), or 380×10−9 m, to about 740 nanometres. Primary properties of visible light are intensity, propagation direction, frequency or wavelength spectrum, and polarisation, while its speed in a vacuum, 299,792,458 meters per second, is one of the fundamental constants of nature. Visible light, as with all types of electromagnetic radiation (EMR), is experimentally found to always move at this speed in vacuum. In common with all types of EMR, visible light is emitted and absorbed in tiny "packets" called photons, and exhibits properties of both waves and particles. This property is referred to as the wave–particle duality. Newton bought a prism and noticed how when the sun shone on it, he got different colours out. This made him very curious. Does this change the light, or does the sunlight have lots of colours that the prism puts into different places? How does the prism do it?
- 3. He discovered that the separation of light was even clearer. There was red, then orange, then yellow, then green, and then blue. Newton was pretty sure that what was happening was that the light from the sun had all these colours in it, and that what the prism was doing was bending them all to go into slightly different directions. To test this he got two prisms and a card with a hole in it. He used the first prism to get the sunlight to make different colours. Then he would choose a colour and put the hole so than only that colour went through into the next prism. He then had a very thin line of red, yellow or some other colour of light going to the second prism. He discovered that when the light came out of the other side of the next prism, it was still the same colour as when it went in. So the prism doesn't change the light's colour. What the prism did do was to bend the path the light went on, so that it hit a different place than when the prism wasn't there. When he tried different colours of light he found that the prism bent them all a little bit differently. That was why light that looked white, which had all the colours in it, made different colours when it went through the prism - the different colours all came out of it in slightly different directions. LAWS OF LIGHT Reflection: When a ray of light strikes a plane mirror, the light ray reflects off the mirror. Reflection involves a change in direction of the light ray. The convention used to express the direction of a light ray is to indicate the angle which the light ray makes with a normal line drawn to the surface of the mirror. The angle of incidence is the angle between this normal line and the incident ray; the angle of reflection is the angle between this normal line and the reflected ray. According to the law of reflection, the angle of incidence equals the angle of reflection. object but inverted.
- 4. Refraction: Refraction is the change in direction of a wave due to a change in its transmission medium. Refraction is essentially a surface phenomenon. The phenomenon is mainly in governance to the law of conservation of energy and momentum. Due to change of medium, the phase velocity of the wave is changed but its frequency remains constant. This is most commonly observed when a wave passes from one medium to another at any angle other than 90° or 0°. Inverse Square Law The inverse square law defines the relationship between the irradiance from a point source and distance. It states that the intensity per unit area varies in inverse proportion to the square of the distance. Distance is measured to the first luminating surface - the filament of a clear blulb, or the glass envelope of a frosted bub. Example: You measure 10.0 lm/m² from a light bulb at 1.0 meter. What will the flux density be at half the distance? Solution: E1=(d1/d2)²*E2 E0.5 m=(1.0/0.5)²*10.0 = 40 lm/m² In optics, Lambert's cosine law says that the radiant intensity or luminous intensity observed from an ideal diffusely reflecting surface or ideal diffuse radiator is directly proportional to
- 5. the cosine of the angle θ between the observer's line of sight and the surface normal. The law is also known as the cosine emission law or Lambert's emission law.
- 6. the cosine of the angle θ between the observer's line of sight and the surface normal. The law is also known as the cosine emission law or Lambert's emission law.