Performance analysis of IEEE 802.11ac based WLAN in wireless communication systems

International Journal of Electrical and Computer Engineering (IJECE)
Vol. 9, No. 2, April 2019, pp. 1131~1136
ISSN: 2088-8708, DOI: 10.11591/ijece.v9i2.pp1131-1136  1131
Journal homepage: http://iaescore.com/journals/index.php/IJECE
Performance analysis of IEEE 802.11ac based WLAN in
wireless communication systems
A. Z. Yonis
College of Electronics Engineering, Ninevah University, Mosul, Iraq
Article Info ABSTRACT
Article history:
Received Jan 27, 2018
Revised May 28, 2018
Accepted Jun 15, 2018
IEEE 802.11ac based wireless local area network (WLAN) is emerging WiFi
standard at 5 GHz, it is new gigabit-per-second standard providing premium
services. IEEE 802.11ac accomplishes its crude speed increment by pushing
on three distinct measurements firstly is more channel holding, expanded
from a maximum of 80 MHz up to 160 MHz modes. Secondly, the denser
modulation, now using 256-QAM, it has the ability to increase the data rates
up to 7 Gbps using an 8×8 multiple input multiple output (MIMO). Finally, it
provides high resolution for both narrow and medium bandwidth channels.
This work presents a study to improve the performance of IEEE 802.11ac
based WLAN system.
Keywords:
IEEE 802.11
Modulation
WLAN
Peak data rate
Copyright © 2019 Institute of Advanced Engineering and Science.
All rights reserved.
Corresponding Author:
A. Z. Yonis,
College of Electronics Engineering,
Ninevah University,
Mosul, Iraq.
Email: aws_zuher@yahoo.com
1. INTRODUCTION
Recently, wireless communications have fundamentally developed because of the trend setting
innovation of cell phones, convenient gadgets and the fast development of Internet of Things (IOT) [1],
astute transportation frameworks and person to person communication. IEEE 802.11 is a well-known
standard that widely used to control the physical layer determinations for executing wireless local area
network (WLAN) computer for various frequency bands such as 900 MHz and 2.4, 3.6, 5, and 60 GHz [2].
At 1997 the basics of IEEE 802.11 was discharged and then the results were revised. This system
with its corrections are focusing on the items of wireless systems such as Wi-Fi. On the other hand, every
modification is revoked when it is established in the last version of the system. The companies resort to
market to get the corrections and updates in order to improve the capabilities of products. These revised
systems will become new standards. Wireless communications heading towards high bandwidth of data
transmission for multi-users at the same time. IEEE 802.11 standards evolution is shown in Figure 1.
This paper introduces the history of IEEE 802.11 standard in section 2. While section 3 presents
how IEEE 802.11 developped and improved to IEEE 802.11ad.The simulation results with detailed
discussions are presented in section 4. Finally, the important conclusions and some suggestions for further
improvement of the proposed work are discussed in section 5.

 ISSN: 2088-8708
Int J Elec & Comp Eng, Vol. 9, No. 2, April 2019 : 1131 - 1136
1132
Figure 1. IEEE 802.11 development from IEEE 802.11A to IEEE 802.11ad
2. HISTORY OF IEEE 802.11 STANDARD
IEEE 802.11a utilizes similar information connect layer convention and casing group to the first one
even the used air interface is OFDM. This IEEE standard is working on 5 GHz band also the peak data rate
reaches to 54 Mbps. On the other hand, the throuhput is around 20 Mbps and this value is obtained according
to the code of error correction distinctive correspondence frameworks such as GSM, LTE and WLAN which
give remote web access to assortment of uses.
The utilization of mobile as an instrument to access the services of internet daily turns out to be
more pressing and fruitful advancement of mobile wireless technology builds the capacity to make high
throughput and minimal effort systems for the client in-movement. Giving intelligent transportation
frameworks stable wireless internet association has turned into an appealing examination field for a long
time. Among the numerous innovations suggested for frameworkswith intelligent transmission, wireless
communications and vehicle to individual correspondence, means to build drivers and travelers comfort,
street security and transport efficiency and give pervasive wireless network to the internet [4]. While IEEE
802.11b has a most extreme crude information rate of 11 Mbps, and furthermore utilizes similar media
access. IEEE 802.11b items showed up on 2000, Wireless communications are ending up progressively
imperative for their flexibility, portability and speed. It is the situation of microwave and laser based
innovations, e.g. Wi-Fi and free space optics, individually. The significance and usage of Wi-Fi have been
developing for supplementing conventional wired systems. Wi-Fi has had an expanding nearness in the
individual home, shaping a remote individual territory arrange, enabling individual gadgets to impart. Point-
to-point and point-to-multipoint arrangements are utilized both inside and outside, requiring specific
directional and omnidirectional radio wires [5].
Confirmed the IEEE 802.11g in 2003 it works (like IEEE 802.11b), in the 2.4 GHz band, likewise
utilizes the same OFDM based transmission. IEEE 802.11g is the third adjustment standard for remote
LANs. This standard is working in 2.4GHz band and has raw data rate of 54Mbps. The throughput of this
IEEE 802.11g reachs 31.4 Mbps if the used multiple access depends the scheme of avoiding collisionin
transmission; this troughput is for 1500 bytes with wireless rate of 54 Mbps. In fact, this throughput can not
be achieved practically due to the implementation of access points, so throughput of packets with size less
than 1500 bytes will have throughput around 3 Mbps if the used rate is 54 Mbps and the packets have 64
bytes [6].
IEEE 802.11 based WLANs are generally utilized in view of its adaptability; Higher throughput can
be achieved by upgrading the execution medium access control layer all things considered medium access
control layer (MAC) outline total component can be utilized. This standard has two types of casing total:
MAC protocol data unit aggregation and the other is MAC service data unit aggregation [7].
IEEE 802.11n is a change that enhances the past IEEE 802.11 standards by including MIMO
antennas i.e. multiple input antennas and multiple output antennas. On the other hand, IEEE 802.11n is
working on two bands: 2.4 GHz and 5GHz. The peak data rate of this standard may reach 600 Mbps intead of
54 Mbps as confirmed bt IEEE and distributed in 2009. Finally, in 2013 IEEE 802.11 is revised to IEEE
802.11 ac. It constructed in light of the 802.11n standard. also, standard is distributed in 2013,which expands
on IEEE 802.11n and it guarantees that throughput has high level, it utilizes high transfer speed and high
quantities of MIMO, and high requests of modulations [8].

Int J Elec & Comp Eng ISSN: 2088-8708 
Performance Analysis of IEEE 802.11ac based WLAN in Wireless Communication Systems (A.Z. Yonis)
1133
3. IEEE 802.11AD STANDARD FEATURES
The physical layer of IEEE 802.11 networks is characterized efficienty through IEEE 802.11ad.
This standard is developed so that it can work on millimeter wave with range of 60GHz. The characteristics
of this band is fully unique and this band of frequency differs from 2.4 GHz and 5 GHz in the conditions of
Wi-Fi network systems. All the items that excuting this standard (IEEE 802.11ad) are carried under the name
of WiGig brand. IEEE 802.11ad basics are depending the protocol of hybrid MAC (medium access control)
which ensures avoiding the collisions and non-cnflict based channel instruments. It additionally utilizes
directional receiving ways to work on 60 GHz with minimum losses in path.So, IEEE 802.11ad is realy
different and contrasts if it is compared to other standards such as IEEE 802.11(b/g/n) because this standard
needs new strategies to investigate its execution [9]. The genuine test for the IEEE 802.11ax standards
improvement is to outperform from perspective of bandwidth in an initial step and after that as in general
execution the Ethernet standard [10], [11].
4. SIMULATION AND RESULTS
The simulation supports the IEEE 802.11a, IEEE 802.11n and IEEE 802.11ac standards with an
extensive variety of settings. A block diagram showing the fundamental circle of the simulation is shown in
Figure 2. The following subsections clarify each block in more subtle details.
Figure 2. Block diagram of the simulation 7
As shows in Figure 3(a), we used type of modulation called BPSK with MSC (0) and code rate;
With code rate 1/2 and we noticed that the maximum value of bit error rate is 9.98e-06 dB when single noise
ratio (SNR) is dB and in theoretical when SNR is 10 dB the value of BER is 3.872e-06.
As shows in Figure 3(b), we used type of modulation called with QPSK 3/4 MSC (2) and code rate
3/4 and we noticed that the maximum value of bit error rate is 9.98e-5 dB when single noise ratio (SNR) is
10 dB and in theoretical when SNR is 15 dB the value of BER is 9.361e-09.
As shows in Figure 3(c), we used type of modulation called with 16 QAM 1/2 MSC (3) and code
rate 1/2 and we noticed that the maximum value of bit error rate is 1.999e-05 when single noise ratio (SNR)
is 20 dB and in theoretical when SNR is 20 dB the value of BER is 1.999e-05.
Figure 4(a), we used type of modulation called with 16 QAM 3/4 MSC (4) and code rate 3/4 and we
noticed that the maximum value of bit error rate is 0.0043 when single noise ratio (SNR) is 15dB and in
theoretical when SNR is 20 dB the value of BER is 2.904e-06. Figure 4(b), we used type of modulation
called with 64 QAM 2/3 MSC (5) and code rate 2/3 and we noticed that the maximum value of bit error rate
is 4.999e-05 when single noise ratio (SNR) is 25 dB and in theoretical when SNR is 25 dB the value of BER
is 4.999e-05 While Figure 4(c), we used type of modulation called with 64 QAM 3/4 MSC (6) and code rate
¾ and we noticed that the maximum value of bit error rate is 2e-05 when single noise ratio (SNR) is 25 dB
and in theoretical when SNR is 25 dB the value of BER 2e-05. Figure 5(a), we used type of modulation
called with 64 QAM 5/6 MSC (7) and code rate 5/6 and we noticed that the maximum value of bit error rate
is 3.999e-05 when single noise ratio (SNR) is 25 dB and in theoretical when SNR is 25 dB the value of BER
is 3.999e-05.

 ISSN: 2088-8708
1134
Figure 3(a). Simulation of IEE 802.11ac with
BPSK1/2
Figure 3(b). Simulation of IEEE 802.11ac with
QPSK ¾
Figure 3(c). Simulation of IEEE802.11 ac with 16 QAM ½
Figure 4(a). Simulation of IEEE 802.11ac with
16QAM 3/4
Figure 4(b). Simulation of IEEE 802.11ac with 64
QAM 2/3
Figure 4(c). Simulation of IEEE 802.11ac with 64 QAM ¾

Int J Elec & Comp Eng ISSN: 2088-8708 
Performance Analysis of IEEE 802.11ac based WLAN in Wireless Communication Systems (A.Z. Yonis)
1135
Figure 5(a). Simulation of IEEE 802.11ac with 64
QAM 5/6
Figure 5(b). Simulation of IEEE 802.11ac with
256QAM
Figure 5(c). Simulation of IEEE 802.11ac with 256 QAM 5/6
Figure 5(b), we used type of modulation called with 256 QAM 3/4 MSC (8) and code rate 3/4 and
we noticed that the maximum value of bit error rate is 4.4996e-05 when single noise ratio (SNR) is 30 dB
and in theoretical when SNR is 35 dB the value of BER 2.495e-10 while Figure 5(c), we used type of
modulation called with 256 QAM 5/6 MSC (9) and code rate 5/6 and we noticed that the maximum value of
bit error rate is 0.00013 when single noise ratio (SNR) is 30 dB and in theoretical when SNR is 35 dB the
value of BER 2.495e-10. As a result, Figure 6 summarizes the performance of the system with different
modulation techniques. So it is preferable to use the BPSK in transmitting the data on the AWGN channel.
Figure 6. BER values for different modulation techniques
5. CONCLUSIONS
This paper presents an adequate analysis and results of the IEEE 802.11ac standard. It also shows its
capability to efficiently perform with the modern communication systems with acceptable performance.
IEEE 802.11 standards give portability support to voice correspondence, wireless information systems can be
partitioned into a few sorts relying upon their zone of scope. Through range changes and speedier remote
0
0.1
0.2
0.3
0.4
0.5
ModulationBPSK QPSK Rate 16QAM Rate 64QAM Rate 256QAM
BER(bps)
Modulation Technique
BER FOR DIFFERENT MODULATION TECHNIQUES AT FEC=3/4

 ISSN: 2088-8708
1136
transmissions, IEEE 802.11ac, ad and 802.11ax promotion are enhancing the execution of superior quality
TV and computerized video streams in the home and propelled applications in big business systems.
They enhance generally client encounter where and at whatever point individuals are associated. All the
applied improvements are designed to increase the speed of data transportation. On the other side, the
frequency will be different because IEEE 802.11ad uses unlicensed 60 GHz band and shorter range
transmissions. The research paper summarizes the execution of the framework with various modulation
methods and it is desirable over utilize the BPSK adjustment method for transmission of the data information
in the AWGN channel.
ACKNOWLEDGMENT
This research study is achieved in the department of Communication Engineering/College of
Electronics Engineering at Ninevah University, Mosul, Iraq.
REFERENCES
[1] E. Y. Adesta, D. Agusman,and A. Avicenna, “Internet of Things (IoT) in Agriculture Industries,” Indonesian
Journal of Electrical Engineering and Informatics (IJEEI), Vol. 5, No. 4, 2017, pp. 376-382.
[2] M. Elkhodr, Q. F. Hassan and S. Shahrestani, “Networks of the Future: Architectures, Technologies, and
Implementations,” Book CRC, 2017.
[3] Y. Park and F. Adachi, “Enhanced Radio Access Technologies for Next Generation Mobile Communication,” Book
springer, pp.20. 2007.
[4] J. Jansons and A. Barancevs, “Using wireless networking for vehicular environment: IEEE 802.11a standard
performance,” 2nd IEEE International Conference on Digital Information Processing and Communications
(ICDIPC), 2012, pp.5-9.
[5] J. A. Carvalho; H. Veiga; N. Marques; C.F.Pacheco, and A.D.Reis, “A Contribution to Laboratory Performance
Measurements of IEEE 802.11 B,G Wep point-to-point Links,” International Conference on Wireless Information
Networks and Systems (WINSYS), 2010, pp.1-4.
[6] J. Jangeun, P. Pushkin, and S. Mihail, “Theoretical Maximum Throughput of IEEE 802.11 and its Applications,”
Second IEEE International Symposium on Network Computing and Applications, 2003, pp. 249-256.
[7] M. S. Kowsar and S. Biswas, “Performance improvement of IEEE 802.11n WLANs via frame aggregation in NS-
3,” IEEE international conference on electrical, computer and communication engineering (ECCE), 2017, pp. 1-6.
[8] N. Al-Ghazu, “A Study of the Next WLAN Standard IEEE 802.11ac Physical Layer,” M. S. Thesis Stockholm,
Sweden, 2013.
[9] K. Chandra, R. V. Prasad, and I. Niemegeers, “Performance Analysis of IEEE 802.11ad MAC Protocol,” IEEE
communications letters, vol. 21, no. 7, 2017, pp. 1513-1516.
[10] D. Deng, K. Chen and R. Cheng, "IEEE 802.11ax: Next Generation Wireless Local Area Networks," 10th
International Conference on Heterogeneous Networking for Quality,Reliability,Security and Robustness, Rhodes,
2014, pp.77-82.
[11] M. P. Putra, D. Perdana and R. M. Negara, “Performance Analysis of Data Traffic Offload Scheme on Long Term
Evolution and IEEE 802.11AH,” TELKOMNIKA (Telecommunication Computing Electronics and Control), vol. 15,
no. 4, 2017, pp. 1659 – 1665.

Performance analysis of IEEE 802.11ac based WLAN in wireless communication systems

More Related Content

What's hot (19)

Similar to Performance analysis of IEEE 802.11ac based WLAN in wireless communication systems (20)

More from IJECEIAES (20)

Recently uploaded (20)

Performance analysis of IEEE 802.11ac based WLAN in wireless communication systems