Performance analysis of new proposed window for

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 02 Issue: 12 | Dec-2013, Available @ http://www.ijret.org 340
PERFORMANCE ANALYSIS OF NEW PROPOSED WINDOW FOR
THE IMPROVEMENT OF SNR & FIGURE OF MERIT
Mousumi Karmakar1
, Priyanka Das2
1
Assistant Professor of Electronics and Communication Engineering
Mallabhum Institute of Technology, P.S: Bishnupur, Dist: Bankura-722122, W.B.,India
mkmit2008@gmail.com
2
Assistant ProfessorofElectronics and Communication Engineering
Mallabhum Institute of Technology, P.S: Bishnupur, Dist: Bankura-722122, W.B.,India
daspriya13@gmail.com
Abstract
The process of communication becomes quite challenging because of the unwanted electrical signals in a communications system.
These undesirable signals, usually termed as noise, are random in nature and interfere with the message signals. As a result the
signal which is collected from receiver side is not accurate level .In this respects, filtering of signal is very important because
noisy signal can mask some important features of the message signal. Hence it is desirable to reduce this noise for proper analysis
of the message signal. The signal to noise ratio (SNR) is one of the important measures for reducing the noise. This paper presents
the study of low pass FIR filter using a new window techniques for signal Processing. The newly designed windowing
filterpresents a new concept for better signal analysis and disturbance detection in the communication systems.The parameters
i.e. Power Spectral Density (PSD), signal to noise ratio (SNR), Error Vector Magnitude (EVM) & Figure of Merit are calculated
of original signal and analysis the performance of new proposed window method used for low pass FIR filter. This new
windowing filter finds applications in signal analysis, communication system and image compression with a lot of other fields.The
results have been concluded using MATLAB R2012 software.
Index Terms:Window method for Noise reduction, Figure of Merit, SNR, EVM, New window performance
------------------------------------------------------------------------------------------------------------------------------------------
1.INTRODUCTION
A signal as referred to in communication systems, signal
processing, and electrical engineering "is a function that
conveys information about the behaviour or attributes of
some phenomenon" [1]. In the physical world, any quantity
exhibiting variation in time or variation in space is
potentially a signal that might provide information on the
status of a physical system, or convey a message between
observers, among other possibilities [2]. The information in
a signal is usually accompanied by noise.
The term noise usually means an undesirable random
disturbance, but is often extended to include unwanted
signals conflicting with the desired signal. These unwanted
signals arise from a variety of sources which may be
considered in one of two main categories:-
a) Interference, usually from a human source
b) Naturally occurring random noise.
Interference arises for example, from other communication
systems (cross talk), 50 Hz supplies and harmonics,
switched mode power supplies, thyristor circuits, ignition
(car spark plugs) motors etc. Naturally occurring external
noise sources include atmosphere disturbance (e.g. electric
storms, lighting, ionospheric effect etc), so called ‘Sky
Noise’ or Cosmic noise which includes noise from galaxy,
solar noise and ‘hot spot’ due to oxygen and water vapour
resonance in the earth’s atmosphere. These sources can
seriously affect all forms of radio transmission and the
design of a radio system (i.e. radio, TV, satellite) must take
these into account.In recent years, several methods of
filtering techniques are used for noise reduction.
In this paper, we have designed a new window technique of
FIR low pass filter for the improvement of SNR. In both
digital filter design and spectral estimation, the choice of a
windowing function can play an important role in
determining the quality of overall results. The main role of
the window [4],[12] is to damp out the effects of the Gibbs
phenomenon that results from truncation of an infinite
series.
2. NEW WINDOW FUNCTION
In this section new window function is presented. It is
defined as [3],[4]

_______________________________________________________________________________________
w(n) = . − . + .
= − ---------(1)
The new window sequence for N= 63 &it’s frequency
response are presented in Fig.1 & 2 respectively with the
help of MATLAB 2012 software.
Fig.1: Proposed Window Response
Fig.2: Frequency response of proposed window
3. CASE STUDY
It is seen that the noise in communication systems is mostly
additive and affects the transmission of signal through a
channel. The objective of this paper is to remove this
random noise from the communication system & produce a
better result. Now from this point of view a new window
method is designed for filtering purpose to get more signal
power than noise power at the output.In this section random
noise is added to a sinusoidal signal and then passed through
a FIR low pass filter using new window function which is
shown in Fig.3.
Fig -3: Block diagram of signal transmission
To check the performance of this new window method, two
signal i.e. noisy sinusoidal signal & filtered signal is taken
[5]. The simulation is done in MATLAB 2012 software.
3.1. Simulation Result
Fig.4: Original Signal
Fig.5: Random noise signal
Input signal i.e. sinusoidal & random noise signal is shown
in Fig.4 & 5 respectively.When this two signals is added it
becomes noisy & the characteristics of the sinusoidal is
distorted. In general, a high "signal-to-noise ratio" at the
output is achieved by passing the noisy signal through a
filter.
0 10 20 30 40 50 60 70
0
0.2
0.4
0.6
0.8
1
1.2
1.4
Samples
Amplitude
Proposed Window Response
N=63
-0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2
-30
-20
-10
0
10
20
30
40
Normalized frequency (w/pi)
Normalizedmagnitude
Frequency response of Proposed Window
N=63 0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1
-1
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
Time
Amplitude
Original Signal
0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1
-1.5
-1
-0.5
0
0.5
1
1.5
2
Time
Amplitude
Random noise signal

_______________________________________________________________________________________
Fig.6: Comparative analysis of original, noisy & filtered
signals
From Fig.6 it is seen that due to filtering process the noise is
almost reduced & the filtered output is within desired level.
The value which is collected from this simulation result is
shown in Table.1
Table.1: Comparative Study of Signals
Parameters Noisy Sinusoidal
Signal
(I/P)
Filtered
Signal
(O/P)
SNR (dB) 4.658 6.942
EVM (%) 58.49 44.97
From Table.1 it is clear that the value of filtered output SNR
is increased compared to noisy signal SNR whereas error
vector magnitude (EVM) is decreased. Mathematically
EVM is expressed as [6]:
EVM =
√
× 100%------------(2)
Generally, if SNR increases by a factor of N, the EVM
reduces by√ , thus leading to more reliable performance of
filter.
3.2 Figure of Merit
To get a quantitative measure on how well a given system is
"really" doing we have calculated the figure of meritas a
ratio of signal-to-noise ratio [7] as follows:
Figure of Merit =
( )#
( )$
-----------(3)
Where, (SNR)o[13] is the ratio of the average signal power
over the average noise power at the output of the filter
&(SNR)iis the ratio of the average signal power over the
average power of the noise at the input of filter. For a
system to be capable of detecting a signal and effective in
eliminating noise, it’s figure of merit should be high. In this
section figure of merit is equal to 1.49, which is calculated
using equation(3).
3.3 Power Spectral Density(PSD)
Power spectral density function (PSD) [8] shows the
strength of the variations(energy) as a function of frequency.
In other words, it shows at which frequencies variations are
strong and at which frequencies variations are weak. PSD is
a very useful tool to identify oscillatory signals from time
series data and to know their amplitude. The unwanted
vibrations can be detected from PSD of a signal.
The PSD of noisy signal & filtered signal using MATLAB
simulation[9] is shown in Fig.7.
Fig.7: PSD of noisy signal & filtered signal
From Fig.7 it is seen that only at 100 Hz the peak amplitude
is high, both for noisy & filtered signal. On the other hand
there is no peak at the other frequencies. So this is the peak
of original signal. Here it is also clear that, at higher
frequency (more than 100 Hz) ripples are negligible for
filtered signal compared to noisy signal.
4. APPLICATION OF NEW WINDOW IN
COMMUNICATION SYSTEM
Filters are widely employed in signal processing and
communication systems in applications such as channel
equalization, noise reduction, radar, audio processing, video
processing, biomedical signal processing, and analysis of
economic and financial data [10]. The primary functions of
filters are one of the followings:
(a) To confine a signal into a prescribed frequency band as
in low-pass, high-pass, and band-pass filters.
(b) To modify the frequency spectrum of a signal as in
telephone channel equalization and audio graphic equalizers.
0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1
-2.5
-2
-1.5
-1
-0.5
0
0.5
1
1.5
2
2.5
Time
Amplitude
Original Signal,Noisy Signal & Filtered Signal
Sinusoidal Signal
Noisy Sinusoidal Signal
Filtered Signal
0 20 40 60 80 100 120 140 160 180 200
0
10
20
30
40
50
60
70
frequency
Amplitude
PSD of noisy signal & filtered signal
noisy
filtered

_______________________________________________________________________________________
(c) To model the input-output relationship of a system such
as telecommunication channels, human vocal tract, and
music synthesizers.
Already we have checked that this new window function is
capable to remove noise from the noisy signal at the output
shown in Fig.6. In this section we have applied this new
window for the improvement of SNR and reduction of noise
at the output of demodulator of communication system
which is shown in Fig.8.
Fig.8: Block diagram of communication system
The simulation is done in MATLAB 2012 software.
4.1. Simulation Result
Fig.9: Original message signal
Fig.10: Modulated signal
Fig.11: Noisy modulated signal
Fig.12: Noisy demodulated signal
Fig.13: Filtered signal
The value which is collected from this simulation result is
shown in Table.2
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
-1
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
Time
Amplitude
Original signal
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
-3
-2
-1
0
1
2
3
Time
Amplitude
Modulated signal
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
-5
-4
-3
-2
-1
0
1
2
3
4
5
Time
Amplitude
Modulated signal + Random noise
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
0
0.5
1
1.5
2
2.5
3
3.5
Time
Amplitude
Demodulated Signal
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
Time
Amplitude
Filtered signal

_______________________________________________________________________________________
Table.2: Comparative study of noisy signal & filtered signal
Parameters Noisy
Modulated
Signal
(I/P)
Filtered
Demodulated
Signal
(O/P)
SNR (dB) 10.109 17.716
EVM (%) 31.23 13.01
Here also to check the performance of the new window
function we have calculated the figure of merit (FOM) using
equation(3).
Figure of Merit =
( )#
( )$
= 1.75
FOM as defined above provides a normalized (SNR)o
performance of the modulation-demodulation schemes and
larger the value of FOM, better is the performance of the
communication system[11] for noise reduction.
4.2 Performance Analysis
Comparing Fig.9 ,12 and 13 it is seen that filtered signal is
more similar to original signal. The filtered signal has
almost same nature like message (original) signal where as
in case of demodulated signal, the features of original signal
is distorted somewhere due to random noise. This distortion
is removed through FIR low pass filter using new window
function (equ.1).
Thus it is proved that this new window method is suitable
for FIR filter design. Instead of commonly used window like
rectangular, hamming, blackman etc. the new window can
be used for any FIR filter design.
5. CONCLUSION
Now-a-days, noises are common in communication channels
and the recovery of the transmitted signals from the
communication path without any noise is considered as one
of the difficult tasks. Various denoising technique have been
proposed till date for the removal of noises from the
transmitted signals. Yet, the effectiveness of those
techniques remains an issue. In this paper a new window
filter is presented at receiver side for the improvement of
SNR and reduction of noise in communication system.
There are several parameters that evaluate the noise
performance of any communication system.The first
parameter that gives the idea about the efficiency of the
system in detecting a signal from a background noise is
SNR. The higher value of output SNR than input SNR is
significantly verified the better performance of new window
filter. The second parameter that evaluates the reliability of
receiver is error vector magnitude (EVM).The new approach
reduces the EVM at receiver output means more reliable
system performance in term of noise reduction. The third
parameter that gives the idea about the capability of noise
elimination at receiver of the communication system is
figure of merit (FOM). For an ideal receiver system figure
of merit should be greater than or equal to unity. Here it is
seen that figure of merit for filtered signal is greater than
unity. Thus the improvement of performance for the new
window filter at receiver was experimentally verified.
6. REFERENCES
[1] Roland Priemer (1991). Introductory Signal
Processing.World Scientific.p. 1.ISBN 9971509199.
[2] Speech processing in embedded systems.
Springer.p. 9.ISBN 0387755802.
[3] “A New Window Function to Design FIR Filter with an
Improved Frequency Response for Suppressing Side-Lobe
Attenuation and Study Comparison with the Other
Windows” by Priyanka Das and MousumiKarmakar,
International Journal of Engineering Research &
Technology (IJERT),Vol. 2 Issue 12, December – 2013,
ISSN: 2278-0181
[4] Oppenheim, A.V., and R.W. Schafer. Discrete-Time
Signal Processing. Upper Saddle River, NJ: Prentice-Hall,
1999, p. 468.Oppenheim, A.V., and R.W. Schafer, Discrete-
Time Signal Processing, Prentice-Hall, 1989, pp. 447-448.
[5] ‘Communication Systems Analog & Digital’ second
edition by R P Singh, S D Sapre; The McGraw-Hill
Companoes.
[6] R.A. Shafik et al., “On the Error Vector Magnitude as a
Performance Metric and Comparative Analysis,” 2nd Int.
Conf.Emerging Technol., Nov. 2006, pp. 27- 31.
[7] Fundamentals of RF and Microwave Noise Figure
Measurements – App.Note 57-1 – Agilent
[8] John G. Proakis, Digital Communications, Mc Graw
Hill, third edition, 1995.
[9] FFT for Spectral Analysis Demo - MathWorks India.htm
[10]L.R.Rabiner and B.Gold , Theory and Application of
Digital Signal Processing. Englewood Cliffs, NJ: Prentice-
Hall 1975.
[11] Noise Performance of Various Modulation
Schemes by Prof. V. Venkata Rao
[12] John G. Proakis and Dimitris G. Manolakis, Digital
Signal Processing, Prentice-Hall, third edition, 1996.
[13] ‘Improvement of Noise Performance in
Phased-Array Receivers’ by Junghyun Kim, Jinho Jeong,
and Sanggeun Jeon;
ETRI Journal, Volume 33, Number 2, April 2011

_______________________________________________________________________________________
BIOGRAPHIES
MousumiKarmakar received B.E
(2005) degree in Electronics and
Communication Engineering from
University Institute of Technology,
Burdwan University. She obtained
M.Tech (2008) in Mechatronics
Engg. from NITTTR, Salt-lake,
kolkata,West Bengal University of
Technology. She is presently
working as an Asst. Professor of
Department of E.C.E atMallabhum
Institute of Technology, Bishnupur,
Bankura-722122, W.B., India.Her
area of interests includesSignals &
Systems, DSP,Microprocessors
&Microcontrollers,Electronics
Circuit design etc. She has an
International Journal publication on
FIR filter design using window
method in IJERT.
Priyanka Das received B.Tech
(2009) degree in Electronics and
Instrumentation Engineering
&M.Tech (2011) degree in Mobile
Communication & Networking
from JIS College of Engineering,
Kalyani, West Bengal University of
Technology. She is presently
working as an Asst. Professor of
Department of E.C.E atMallabhum
Institute of Technology, Bishnupur,
Bankura-722122, W.B., India. Her
area of interests include Signals &
Systems, Digital signal processing,
Control System, Electronics Circuit
design etc. She has an International
Journal publication on FIR filter
design using window method in
IJERT.

Performance analysis of new proposed window for

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Performance analysis of new proposed window for (20)

More from eSAT Publishing House (20)

Recently uploaded (20)

Performance analysis of new proposed window for