PID-based temperature control device for electric kettle

International Journal of Electrical and Computer Engineering (IJECE)
Vol. 9, No. 3, June 2019, pp. 1683∼1693
ISSN: 2088-8708, DOI: 10.11591/ijece.v9i3.pp1683-1693 Ì 1683
PID-based temperature control device for electric kettle
Mohd Badril Nor Shah, Norfahaniza Zailan, Amar Faiz Zainal Abidin, Mohd Firdaus Halim, Khalil
Azha Annuar, Arman Hadi Azahar, Muhamad Haniff Harun, Muhammad Faizal Yaakub
Centre for Robotics & Industrial Automation, Fakulti Teknologi Kejuruteraan, Universiti Teknikal Malaysia Melaka,
Malaysia
Article Info
Article history:
Received Aug 13, 2018
Revised Nov 23, 2018
Accepted Dec 15, 2018
Keywords:
PID controller
Gain scheduling
On-off controller
Water temperature control
ABSTRACT
A normal electric kettle usually is intended to boil water until boiling point and cannot
be controlled. Most of the kettle does not provide the temperature display for user to
track the current temperature reading. Thus, this project is inspired from the short-
coming of most kettles that are sold at the market. By using Arduino microcontroller,
a device is developed to control water temperature inside electric kettle. To provide
automated temperature control, PID controller is chosen since it can provides precise
water temperature control with less fluctuation. The device is also equipped with the
display of the current water temperature and desired temperature. The device is tested
to an electric kettle and the performance of PID controller in controlling water temper-
ature is compared to on-off controller. An analysis is performed based on the amount
of fluctuation with respect to desired temperature to verify the efficacy of the designed
circuit and controller. It is found that the developed device and PID controller are ca-
pable to control the water temperature inside kettle based on the desired temperature
set by user with less amount of fluctuation.
Copyright c 2019 Institute of Advanced Engineering and Science.
All rights reserved.
Corresponding Author:
Mohd Badril Nor Shah,
Fakulti Teknologi Kejuruteraan,
Universiti Teknikal Malaysia Melaka (UTeM), Malaysia.
Phone: +606-234 6591
Email: badril@utem.edu.my
1. INTRODUCTION
A common electric kettle consists of two electrical parts, that are heat element and on-off switch as
depicted in Figure 1. When electric power supplied to the heat element, it will heats up the water inside kettle
at full power to bring the water at 100◦
C. The generated steam pressure subsequently will induce the on-off
switch to stop the heating process. Based on this simple process, an electric kettle is only serve one purpose:
to boil water.
Figure 1. Common parts of electric kettle
Journal homepage: http://iaescore.com/journals/index.php/IJECE

1684 Ì ISSN: 2088-8708
To enable the capability of electric kettle of controlling water temperature, it should be equipped with
a device that can measure water temperature inside the kettle, thus providing data for the controller of the
device to perform correct control action to the heat element. With a correct selection and proper design of the
controller, a precise temperature control can be achieved with minimal ﬂuctuation. One of the most prominent
controller that can be used in this application is PID controller.
PID controller widely used in industry since it have simple structure and does not require mathematical
derivation. It contain three terms: proportional, derivative and integration of the error reading which those will
be summed together thus producing analog signal to the actuator to provide treatment for both transient and
steady state response. It has been proven to work in controlling linear and nonlinear, fast and slow response
systems. With proper tuning method to obtain the suitable PID gains, the precise and stable water temperature
at desired setpoint can be prepared.
There are many applications can be adopted if an electric kettle is able to produce warm water at
desired level temperature. For example, at 37◦
C water temperature, a guardian can prepare warm formula milk
for their babies or toddlers [1]. Powder milk is best prepared at 60◦
C to obtain perfect solubility [2]. A coffee
enthusiast always require heated water of 93◦
C for brewing a delicious coffee drink [3]. Tea is best to be
prepared at 82◦
C for maximum ﬂavour extraction from tea leaves [3].
By having an external device that can control temperature of electric kettle, user does not have to
buy an expensive water warmer or similar device to obtain their preferred temperature of warm water. By
using a cheap electric kettle and the proposed device that is developed in this project, user is able to obtain
the warm water at the desired temperature. There are a few almost similar work has been done which can
be used as a reference for this work. In [4], the project of controlling air temperature inside closed case is
developed based on PIC16F877 microcotroller. LM35 temperature sensor is used for temperature measurement
and proportional controller is used as control algorithm to drive DC-powered lamp and DC-powered fan to
control air temperature inside the case. Temperature control inside drying chamner is done by [5]. Arduino
Mega 2560 microcontroller is used as a main part and MLX90614 infrared sensor is used for temperature
measurement. The microcontoller perform on-off algorithm to control magnetron to control air temperature
inside chamber. The magnetron is AC-powered equipment which is driven by TRIAC-based circuit which is
activated by PWM signal given by microcontroller. Temperature control of beer brewing process is done in [6]
by utilizing Arduino UNO microcontroller and DS180B20 temperature sensor. On-off, proportional and PID
controller are tested to compare the control performance in controlling beer temperature.
2. CIRCUIT DESIGN
The proposed device consists of six main parts: microcontroller, heater driver circuit, temperature
sensor, temperature display, reference temperature input and control algorithm. Microcontroller acts as main
brain for the device. It provides automated control of temperature reading, temperature display and heater
control. Arduino microcontroller is chosen this project since it provides large library and wide hardware support
[7].
To enable to capability of temperature control inside kettle, temperature sensor should be utilized.
DS180B20 temperature sensor is used since it is water-proof and compatible to be interfaced to any microcon-
troller using a single digital pin, and even possible to connect multiple same sensors to the same pin. The sensor
has a unique 64-bit ID burned-in at the factory to differentiate them which enable the multiple connection at
the same pin of microcontroller. Power supply for the sensor is 3.0-5V and capable to measure temperature
range from -55◦
C to 125◦
C.
For heater driver circuit, solid state relay SSR is used since it is easy to be interfaced between micro-
controller and AC power supply. It is constructed based on TRIAC-based circuit. It should be noted that to
drive SSR to control AC voltage, low frequency PWM (e.g: 0.1 times than the AC voltage frequency) should
be used to obtain uniform cycle of AC voltage as illustrated in Figure 2. High frequency PWM (e.g. PWM
frequency less frequency of AV voltage) of driving SSR will induce non-uniform phase angle of AC voltages
thus making linear relationship between heater power and PWM duty cycle is not possible. Figure 2 and Figure
3 show the effect of AC voltage output when it is driven by low and high PWM frequency that supplied to SSR.
In this work, low frequency PWM can be used for water temperature control since water temperature has slow
step response.
IJECE, Vol. 9, No. 3, June 2019 : 1683 – 1693

IJECE ISSN: 2088-8708 Ì 1685
[] []
Figure 2. Low frequency PWM in driving an SSR will produce uniform cycle of AC voltage output. (a) 40%
duty cycle (b) 80% duty cycle
Figure 3. High freqency PWM to drive an SSR will cause nonuniform phase angle trigger of AC voltage
output
A variable resistor is used to allow user to set their desired water temperature, and seven segment
display is used to show the desired temperature and the current water temperature inside kettle. For control
algorithm, PID controller is used in providing automated temperature control, where the PID is coded inside
microcontroller. The details of the PID controller and its design is explained in the next section. Figure 4 shows
the field diagram reflecting a microcontroller connected with input and output components.
Figure 4. The circuit arrangement of this project
3. PID CONTROLLER
PID is a proportional-integral-derivative controller, which control loop feedback mechanism. It is
commonly used in industrial control system. The first PID controller was develop by Elmer Sperry in 1911
and it is used to automate a ship steering mechanism. On 1922, the first theoretical paper on PID control was
develop by Nicolas Minorsky, which then was applied to automatic steering of ships [8]. Figure 5 is the block
diagram of a system controlled by PID controller where y(t) is controlled output, r(t) is reference signal, e(t)
is error signal and u(t) is control signal.
PID-based temperature control device... (Mohd Badril Nor Shah)

1686 Ì ISSN: 2088-8708
Figure 5. PID controller block diagram
PID control signal is the sum of three terms which are based on the error measurement, that are
u(t) = Kp + Ki
∞
0
e(t)dt + Kd
d
dt
e(t) (1)
where e(t) = r(t)−y(t), Kp is proportional constant, Ki is integral constant and Kd is derivative constant. The
value of Kp, Ki and Kd are the key in providing stable and desired transient response which can be obtained
by using heuristic methods, analytical methods, frequency response method, optimization method and adoptive
turning methods [9].
Nowadays, PID control algorithm is always implemented in microcontroller to enable compact design
of a product. However, the integral and derivative operation in PID equation of (1) cannot be performed directly
by microcontroller. Hence, the integral and derivative term of (1) need to be converted to discrete form. Starting
with the derivative term, we can use the following difference equation as an approximation, such that;
d
dt
e(t) ≈
e(k) − e(k − 1)
Ts
(2)
where e(k) is error signal in discrete domain, e(k−1) is previous error signal and Ts is sampling time. Equation
(2) is the approximate slope of the tangent line at e(t). The approximation of integral term can be written such
that
∞
0
e(t)dt ≈ Ts
∞
0
e(k) (3)
With these approximations, we can rewrite PID control algorithm in discrete form
u(k) = Kpe(k) + Ki Ts
∞
0
e(k) + Kd
e(k) − e(k − 1)
Ts
(4)
The details derivation and more precise approximation of PID controller in discrete form can be found in
[9, 10].
The kernel code of implementing discrete PID of (4) in Arduino IDE environment software is shown
in Figure 6. Arduino IDE is a software designed for Arduino which allows user to write code in C language,
compile, send/receive to/from microcontroller. Kp, Ki and Kd of PID are the parameters that need to be
tuned. In this project, the heuristic approach is be used to determine the appropriate values of PID gains. The
procedure of determining the PID gains is explained as follows:
(a) Set all gains to zero.
(b) Increase the Kp gain until the response steadily oscillate.
(c) Increase the Kd gain until the oscillations signiﬁcantly reduced.
(d) Repeat steps (ii) and (iii) until the response is stable with minimal oscillation.
(e) Increase the Ki gain to bring the response to the set point.
IJECE, Vol. 9, No. 3, June 2019 : 1683 – 1693

IJECE ISSN: 2088-8708 Ì 1687
Note that the above procedure is valid for open loop stable plant [11]. For unstable system, advance tuning
method is required.
unsigned long Now;
unsigned long LastTime;
double SamplingTime=0;
double Error;
double SumError = 0;
double RateError;
double LastError = 0;
void PID(float setpoint, float output, float kp,
float ki, float kd)
{
Now = millis();
SamplingTime = (double)(Now - LastTime)*pow(10,-3);
Error = setpoint - output;
SumError = SumError + (Error*SamplingTime);
RateError = (Error - LastError)/SamplingTime;
LastError = Error;
LastTime = Now;
Output = kp*Error + ki*SumError + kd*RateError;
return Output;
}
Figure 6. Code of PID control algorithm
4. RESULTS AND DISCUSSION
The block diagram for overall system of this device that is connected to electric kettle is illustrated in
Figure 7, where T(t) is water temperature inside kettle and Td is desired temperature. e(t) is error signal, as in
.For real-time results, the hardware prototype of this project is connected to an 1500 Watt electric kettle and a
PC (for data logging purpose) to verify the performance of the project as shown in Figure 8. For performance
analysis of PID controller, the response of water temperature in the kettle is compared to on-off controller. The
results are presented in several cases as tabulated in Table 1. The interface of the developed device is depicted
in Figure 9 where the seven segment displays are to display current water temperature inside kettle, desired
temperature from user and PID controller gains. DS180B20 sensor probe is immersed inside the kettle and the
plugtop of electric kettle is connected to the device through switch socket outlet. The device also equipped
with a knob to enable user to set their desired temperature. The toggle switch is to select the controller (either
PID or on-off controller) for temperature control operation.
Figure 7. PID controller block diagram

1688 Ì ISSN: 2088-8708
Figure 8. Temperature control device connected to electric kettle and PC
Figure 9. The interface of temperature control device
Table 1. Experiment Cases
Experiment Case Desired Temperature Controller Type
CASE 1 45◦
C PID
CASE 2 65◦
C PID
CASE 3 80◦
C PID
CASE 4 45◦
C On-off
CASE 5 65◦
C On-off
CASE 6 80◦
C On-off
As explained in previous section, PID controller has gain that need to be tuned which are Kp, Ki and
Kd. By using heuristic approach, the gain of PID controller can be determined. Based on the tuning procedure
explained in Section III, after several tuning attempts for 45◦
C, 65◦
C and 80◦
C temperature set point, the
IJECE, Vol. 9, No. 3, June 2019 : 1683 – 1693

IJECE ISSN: 2088-8708 Ì 1689
appropriate gains are successfully obtained and shown in Table 2. The PWM period of control signal u(t)
is set to 1 s. Note that the tuning is done when water volume at 500 ml and intial water temperature is 29◦
C.
The approach to assign different values of PID gain for different set point is known as ‘gain scheduling’ method.
It is also found the execution time for the microcontroller to implement the whole PID control algorithm is 1.13
s which including data logging to PC through USB communication. For performance analysis, the maximum
fluctuation of water temperature along the desired temperature is recorded as depicted in Figure 10.
Table 2. The PID Gains for Different Desired Temperature
Desired Temperature Kp Ki Kd
Below 55◦
C 8 5 16
55◦
C - 75◦
C 8 5 18
76◦
C - 95◦
C 8 5 25
Figure 10. The definition of maximum fluctuation in this project.
Figure 11(a) to Figure 11(c) show the response of water temperature inside kettle when the device is
using PID controller. For the CASE 1 experiment, the desired temperature is set at 45◦
C and it is found the
PID controller is able to generate appropriate PWM signal to the heater thus result in less amount fluctuation of
water temperature. The highest fluctuation recorded at this case is 1.5◦
C. Same performance of PID controller
can be seen when the desired temperature is set at 65◦
C and 80◦
C where the water temperature is almost same
with the desired temperature with a very small fluctuation. The maximum fluctuation recorded for CASE 2 and
CASE 3 are 1.3◦
C and 1.8◦
C. For comparison purpose, the device also performs on-off controller to control
the water temperature. The control signal u(t) for on-off controller is expressed by:
u(t) = sign[e(t)]
=



u(t) = 1 if e(t) > 0
u(t) = 0 if e(t) = 0
u(t) = −1 if e(t) < 0
(5)
However, for case u(t) = −1 if e(t) < 0 has no meaning in this project, thus the term is omitted from the
equation. Equation (5) reflect the on-off operation of heater: when T(t) < Td(t), the heater is activated, else
T(t) ≥ Td(t)), the heater is deactivated. The time taken for the controller to perform the whole instruction
including on-off control algorithm is 1.10 s. The results when the device perform the on-off controller are
shown in Figure 12(a) to Figure 12(c). From the figure, a large amount of overshoot can be seen at water
temperature response. On-off controller gives instant on and off signal to heater and this type of signal unable
to regulate the water temperature with less fluctuation within desired temperature. The amount of fluctuation
for CASE 7, CASE 8 and CASE 9 are 5.1◦
C, 6.6◦
C and 7.5◦
C. The maximum fluctuation magnitude of all
experiment cases is summarized in Table 3.

1690 Ì ISSN: 2088-8708
(a) (b)
(c)
Figure 11. The response of water temperature inside electric kettle when using PID controller at 45◦
C, 65◦
C
and 80◦
C (Legend - Blue: desired temperature, red: water temperature inside kettle, yellow: control signal)
(a) (b)
(c)
Figure 12. The response of water temperature inside electric kettle when using on-off controller at 45◦
C, 65◦
C
and 80◦
C (Legend – Blue: desired temperature, red: water temperature inside kettle, yellow: control signal)
Based on the results, it can be concluded that PID controller is able to provide less amount of water
temperature ﬂuctuation as compare to on-off controller thus making it suitable for precise temperature control.
However, in this work, the experiments are done by using 500 ml of water. For more water volume, the PID
require different set of gains for precise temperature control at different desired temperature. Therefore, for
future improvement, different structure of PID or advance controller shall be used which can cover various
amount of water volume without performing tedious work to determine controller gain in various conditions.
IJECE, Vol. 9, No. 3, June 2019 : 1683 – 1693

IJECE ISSN: 2088-8708 Ì 1691
Table 3. The Maximum Fluctuation of Water Temperature Inside Kettle for Each Experiment Case
Experiment Case Desired Temperature Maximum Fluctuation
CASE 1 45◦
C 1.5◦
C
CASE 2 65◦
C 1.3◦
C
CASE 3 80◦
C 1.8◦
C
CASE 4 45◦
C 5.1◦
C
CASE 5 65◦
C 6.6◦
C
CASE 6 80◦
C 7.5◦
C
ACKNOWLEDGEMENT
The authors would like to thank UTeM for sponsoring this work under short-term grant no. PJP/2017/FTK-
CERIA/S01556.
REFERENCES
[1] J. Marshall and S. Stuart, Child Development. Heinemann Educational, 2001.
[2] S. Anup, J. A. H., and C. R. Shrikant, “Functionality of Milk Powders and Milk-Based Powders for End
Use Applications - A Review,” Comprehensive Reviews in Food Science and Food Safety, vol. 11, no. 5,
pp. 518–528, 2012.
[3] K. Hansen and T. Arndorfer, The Complete Idiot’s Guide to Coffee and Tea. DK Publishing, 2006.
[4] Khairurrijal, A. Mikrajuddin, and B. Maman, “Home-made PIC 16F877 Microcontroller-Based Tempera-
ture Control Cystem for Learning Automatic Control,” Computer Applications in Engineering Education,
vol. 19, no. 1, pp. 10–17, 2011.
[5] S. K. Korkua, S. Chandhaket, K. Thinsurat, and K. Pornbandit, “Design of Automatic Phase-Controlled
Converter Based onTemperature for Microwave Drying System,” in 2016 2nd IEEE International Sympo-
sium on Robotics and Manufacturing Automation (ROMA), Sept 2016, pp. 1–6.
[6] M. Weeks, “Arduino Controlled Brewing,” in SoutheastCon 2015, April 2015, pp. 1–5.
[7] M. Banzi, Getting Started with Arduino. Maker Media Inc., 2015.
[8] S. Bennett, “Nicholas Minorsky and the Automatic Steering of Ships,” IEEE Control Systems Magazine,
vol. 4, no. 4, pp. 10–15, November 1984.
[9] K. ˚Astr¨om and T. H¨agglund, PID Controllers: Theory, Design and Tuning. Instrument Society of
America, 1995.
[10] J. Charais and R. Lourens, “Software PID Control of an Inverted Pendulum Using the PIC16F684,” Ap-
plication Note AN964, Microchip Technology Inc., 2004.
[11] K. H. Ang, G. Chong, and Y. Li, “PID Control System Analysis,Design and Technology,” IEEE Transac-
tions on Control Systems Technology, vol. 13, no. 4, pp. 559–576, July 2005.
BIOGRAPHIES OF AUTHORS
Mohd Badril Nor Shah received the M. Eng. degree in Mechatronic and Automatic Control,
and the Ph.D. degree in Electrical Engineering (Control) from Universiti Teknologi Malaysia,
Johor Bahru, Malaysia, in 2011 and 2015, respectively. He also has several years of experience
as an Engineer in building and facility maintenance engineering. His research interests include
networked control system, real-time control system, robust control, and controller area network
(CAN).

1692 Ì ISSN: 2088-8708
Nurfahaniza Zailan is a student of Bachelor of Electronic Engineering Technology (Industrial
Automation and Robotics) from Universiti Teknikal Malaysia Melaka.
Amar Faiz Zainal Abidin received his ﬁrst degree M. Eng. (Hons) in Electrical and Elec-
tronics Engineering from The University of Nottingham, Malaysia and M.Eng. from Univer-
siti Teknologi Malaysia. He is currently attached as an academic staff with Universiti Teknikal
Malaysia Melaka. His research interests are including multi-objective optimization and nature-
inspired optimization algorithm.
Mohd Firdaus Abdul Halim received his ﬁrst degree M. Eng. (Hons) in Electrical Power System
from Universiti Tenaga Nasional and M. Eng. from University of Applied Sciences, Rosenheim.
He is an academic staff with Universiti Teknikal Malaysia Melaka. Currently, his research is
focused in are of renewable energy, power system and power generation.
Khalil Azha Anuar received the B. Eng (Hons) in Electronic Engineering and M. Eng. in Mecha-
tronics and Automatic Control in 2006 and 2014 from Universiti Teknologi Malaysia. Currenly
he is a lecturer at the Universiti Teknikal Malaysia Melaka. His primary interests related to opti-
mization, control and automation system engineering.
Arman Hadi Azahar received the B. Eng (2010) and MSc (2013) in Mechatronic Engineering
from Universiti Teknikal Malaysia Melaka. Currenly he is a lecturer at the Universiti Teknikal
Malaysia Melaka. His primary interests related to control system and mechatronic engineering.
Mohd Haniff Harun received the B.Eng (2010) and MSc (2013) from Universiti Teknikal
Malaysia Melaka. Currenly he is a lecturer at the Universiti Teknikal Malaysia Melaka. His
primary interests related to vision system and mechatronic engineering.
IJECE, Vol. 9, No. 3, June 2019 : 1683 – 1693

IJECE ISSN: 2088-8708 Ì 1693
Muhammad Faizal Yaakub received the B.Eng in Electronic Engineering from Universiti
Teknologi Malaysia in 2004 and M. Eng in Electrical Engineering from Universiti Tun Hus-
sein Onn in 2013. Currently he is a lecturer at the Universiti Teknikal Malaysia Melaka. His
main research interests are related to power electronics, automotive electronics, power quality
mitigation and renewable energy.

PID-based temperature control device for electric kettle

More Related Content

What's hot (20)

Similar to PID-based temperature control device for electric kettle (20)

More from IJECEIAES (20)

Recently uploaded (20)

PID-based temperature control device for electric kettle