signal and systems basics for engineering

EE-2027 SaS, L3: 1/20
Lecture 3: Signals & Systems Concepts
Systems, signals, mathematical models. Continuous-
time and discrete-time signals. Energy and power
signals. Linear systems. Examples for use
throughout the course, introduction to Matlab and
Simulink tools.
Specific objectives:
• Introduction to systems
• Continuous and discrete time systems
• Properties of a system
• Linear (time invariant) LTI systems
• System implementation in Matlab and Simulink

EE-2027 SaS, L3: 2/20
Lecture 3: Resources
SaS, Oppenheim & Willsky, C1
MIT notes, Lecture 2
Mastering Matlab 6, Prentice Hall
Mastering Simulink 4
Matlab help

EE-2027 SaS, L3: 3/20
Linear Systems
A system takes a signal as an input and transforms it into
another signal
Linear systems play a crucial role in most areas of science
– Closed form solutions often exist
– Theoretical analysis is considerably simplified
– Non-linear systems can often be regarded as linear, for
small perturbations, so-called linearization
For the remainder of the lecture/course we’re primarily going
to be considering Linear, Time Invariant systems (LTI) and
consider their properties
continuous
time (CT)
discrete
time (DT)
y(t)
x(t)
y[n]
x[n]

EE-2027 SaS, L3: 4/20
Examples of Simple Systems
To get some idea of typical systems (and their properties),
consider the electrical circuit example:
which is a first order, CT differential equation.
Examples of first order, DT difference equations:
where y is the monthly bank balance, and x is monthly net deposit
which represents a discretised version of the electrical circuit
Example of second order system includes:
System described by order and parameters (a, b, c)
)
(
1
)
(
1
)
(
t
v
RC
t
v
RC
dt
t
dv
s
c
c


]
1
[
01
.
1
]
[
]
[ 

 n
y
n
x
n
y
]
[
]
1
[
]
[ n
f
k
RC
k
n
v
k
RC
RC
n
v





)
(
)
(
)
(
)
(
2
2
t
x
t
cy
dt
t
dy
b
dt
t
y
d
a 



EE-2027 SaS, L3: 5/20
First Order Step Responses
People tend to visualise systems in terms of their responses
to simple input signals (see Lecture 4…)
The dynamics of the output signal are determined by the
dynamics of the system, if the input signal has no
dynamics
Consider when the input signal is a step at t, n = 1, y(0) = 0
First order CT differential system First order DT difference system
]
1
[
]
1
[
)
1
](
[ 



 n
ku
n
y
ak
n
y
)
1
(
)
(
)
(


 t
u
t
ay
dt
t
dy
t
u(t)
y(t)

EE-2027 SaS, L3: 6/20
System Linearity
Specifically, a linear system must satisfy the two properties:
1 Additive: the response to x1(t)+x2(t) is y1(t) + y2(t)
2 Scaling: the response to ax1(t) is ay1(t) where aC
Combined: ax1(t)+bx2(t)  ay1(t) + by2(t)
E.g. Linear y(t) = 3*x(t) why?
Non-linear y(t) = 3*x(t)+2, y(t) = 3*x2
(t) why?
(equivalent definition for DT systems)
x
y
The most important property that a system
possesses is linearity
It means allows any system response to be
analysed as the sum of simpler responses
(convolution)
Simplistically, it can be imagined as a line

EE-2027 SaS, L3: 7/20
Bias and Zero Initial Conditions
Intuitively, a system such as:
y(t) = 3*x(t)+2
is regarded as being linear. However, it does not satisfy the
scaling condition.
There are several (similar) ways to transform it to an
equivalent linear system
Perturbations around operating value x*
, y*
Linear System Derivative
Locally, these ideas can also be used to linearise a non-
linear system in a small range
)
(
*
3
)
(
)
(
)
(
,
)
(
)
( *
*
t
t
y
t
y
t
x
t
x
t
x
y
y
x









)
(
3
)
( t
x
t
y 



EE-2027 SaS, L3: 8/20
Linearity and Superposition
Suppose an input signal x[n] is made of a linear sum of
other (basis/simpler) signals xk[n]:
then the (linear) system response is:
The basic idea is that if we understand how simple signals
get affected by the system, we can work out how complex
signals are affected, by expanding them as a linear sum
This is known as the superposition property which is true for
linear systems in both CT & DT
Important for understanding convolution (next lecture)
 



 k k
k n
x
a
n
x
a
n
x
a
n
x
a
n
x 
]
[
]
[
]
[
]
[
]
[ 3
3
2
2
1
1
 



 k k
k n
y
a
n
y
a
n
y
a
n
y
a
n
y 
]
[
]
[
]
[
]
[
]
[ 3
3
2
2
1
1

EE-2027 SaS, L3: 9/20
Definition of Time Invariance
A system is time invariant if its behaviour and characteristics are
fixed over time
We would expect to get the same results from an input-output
experiment, if the same input signal was fed in at a different time
E.g. The following CT system is time-invariant
because it is invariant to a time shift, i.e. x2(t) = x1(t-t0)
E.g. The following DT system is time-varying
Because the system parameter that multiplies the input signal is
time varying, this can be verified by substitution
))
(
sin(
)
( t
x
t
y 
))
(
(
))
(
sin(
))
(
sin(
)
( 0
1
1
0
1
2
2 t
t
x
y
t
t
x
t
x
t
y 




]
[
]
[ n
nx
n
y 
]
1
[
]
[
]
1
[
]
[
0
]
[
]
[
]
[
2
2
1
1








n
n
y
n
n
x
n
y
n
n
x




EE-2027 SaS, L3: 10/20
System with and without Memory
A system is said to be memoryless if its output for each value of
the independent variable at a given time is dependent on the
output at only that same time (no system dynamics)
e.g. a resistor is a memoryless CT system where x(t) is current
and y(t) is the voltage
A DT system with memory is an accumulator (integrator)
and a delay
Roughly speaking, a memory corresponds to a mechanism in the
system that retains information about input values other than
the current time.
2
2
])
[
]
[
2
(
]
[ n
x
n
x
n
y 

 


n
k
k
x
n
y ]
[
]
[
]
1
[
]
[ 
 n
x
n
y
]
[
]
1
[
]
[
]
[
]
[
1
n
x
n
y
n
x
k
x
n
y
n
k









EE-2027 SaS, L3: 11/20
System Causality
A system is causal if the output at any time depends on values of
the output at only the present and past times. Referred to as
non-anticipative, as the system output does not anticipate
future values of the input
If two input signals are the same up to some point t0/n0, then the
outputs from a causal system must be the same up to then.
E.g. The accumulator system is causal:
because y[n] only depends on x[n], x[n-1], …
E.g. The averaging/filtering system is non-causal
because y[n] depends on x[n+1], x[n+2], …
Most physical systems are causal
 


n
k
k
x
n
y ]
[
]
[
 

 

M
M
k
M k
n
x
n
y ]
[
]
[ 1
2
1

EE-2027 SaS, L3: 12/20
System Stability
Informally, a stable system is one in which small input signals lead
to responses that do not diverge
If an input signal is bounded, then the output signal must also be
bounded, if the system is stable
To show a system is stable we have to do it for all input signals.
To show instability, we just have to find one counterexample
E.g. Consider the DT system of the bank account
when x[n] = [n], y[0] = 0
This grows without bound, due to 1.01 multiplier. This system is
unstable.
E.g. Consider the CT electrical circuit, is stable if RC>0, because it
dissipates energy
V
y
U
x
x 


 :
]
1
[
01
.
1
]
[
]
[ 

 n
y
n
x
n
y
)
(
1
)
(
1
)
(
t
v
RC
t
v
RC
dt
t
dv
s
c
c



EE-2027 SaS, L3: 13/20
Invertible and Inverse Systems
A system is said to be invertible if distinct inputs lead to distinct
outputs (similar to matrix invertibility)
If a system is invertible, an inverse system exists which, when
cascaded with the original system, yields an output equal to
the input of the first signal
E.g. the CT system is invertible:
y(t) = 2x(t)
because w(t) = 0.5*y(t) recovers the original signal x(t)
E.g. the CT system is not-invertible
y(t) = x2(t)
because distinct input signals lead to the same output signal
Widely used as a design principle:
– Encryption, decryption
– System control, where the reference signal is input

EE-2027 SaS, L3: 14/20
Systems are generally composed of components (sub-systems).
We can use our understanding of the components and their
interconnection to understand the operation and behaviour of
the overall system
Series/cascade
Parallel
Feedback
System Structures
System 1 System 2
x y
System 1
System 2
x y
+
System 2
System 1
x y
+

EE-2027 SaS, L3: 15/20
Systems In Matlab
A system transforms a signal into another signal.
In Matlab a discrete signal is represented as an indexed
vector.
Therefore, a matrix or a for loop can be used to
transform one vector into another
Example (DT first order system)
>> n = 0:10;
>> x = ones(size(n));
>> x(1) = 0;
>> y(1) = 0;
>> for i=2:11
y(i) = (y(i-1) + x(i))/2;
end
>> plot(n, x, ‘x’, n, y, ‘.’)

EE-2027 SaS, L3: 16/20
System Libraries in Simulink

EE-2027 SaS, L3: 17/20
Example 1: Voltage Simulation
Click File-New to create a new workspace, and drag
and drop objects from the library onto the workspace.
Selecting Simulation-Start from the pull down menu
will run the dynamic simulation. Click on the blocks
to view the data or alter the run-time parameters

EE-2027 SaS, L3: 18/20
Example 2: Mass-Spring Simulation
Mass-spring system demonstration in Simulink
Square wave input signal, oscillatory output signal

EE-2027 SaS, L3: 19/20
Lecture 3: Summary
Whenever we use an equation for a system:
• CT – differential
• DT – difference
The parameters, order and structure represent the system
There are a large class of systems that are linear, time
invariant (LTI), these will primarily be studied on this
course.
Other system properties such as causality, stability,
memory and invertibility will be dealt with on a case by
case basis
Matlab and Simulink are standard tools for analysing,
designing, simulating complex systems.
Used for system modelling and control design

EE-2027 SaS, L3: 20/20
Lecture 3: Exercises
SaS OW Q1-27 to Q1-31
Matlab and Simulink
1) Enter the DT first-order system described on Slide 15
into Matlab and check the response
2) Create the CT first-order system described on Slide
17 into Simulink and check the response
3) Run the Mass-Spring simulation mentioned on Slide
18 (this is one of Simulink’s in-built demonstration).
Have a look at how each of the blocks are configured

signal and systems basics for engineering

More Related Content

Similar to signal and systems basics for engineering (20)

More from ArunaDeviAssociatePr (9)

Recently uploaded (20)

signal and systems basics for engineering