Silencers panels-engineering-guide

S E C T I O N M
Engineering Guide
Noise Control
Please refer to the Price Engineer’s HVAC Handbook
for more information on Noise Control.

ENGINEERINGGUIDE-NOISECONTROL
M-2 For more information on additional imperial and metric sizes, © Copyright Price Industries Limited 2014.
please visit www.priceindustries.com or contact your local Price representative.
Noise Control
Engineering Guide
Terminology
Near Field
The sound field immediately surrounding
the source where the sound pressure is
influenced by the radiation characteristics
of the sound source. In this field the sound
pressure and the particle velocity are out
of phase.
Negative Air Flow
See Reverse Air Flow.
Noise
Any unwanted sound or meaningless sound
of greater than usual volume.
NR (Noise Reduction)
A value that represents the difference in
sound pressure level between any two
points along the path of sound propagation.
The unit of measurement is decibels (dB).
NRC (Noise Reduction Coefficient)
A measure of the acoustical absorption
performance of a material, expressed as
a single value. This value is calculated by
averaging the material’s sound absorption
coefficients at 250, 500, 1000 and 2000 Hz
and rounding to the nearest multiple of 0.05.
Octave
The interval between two sounds having a
frequency ratio of 2.There are 8 octaves on
the keyboard of a standard piano.
Octave Band
A segment of the frequency spectrum
separated by an octave.
Pascal (Pa)
A metric unit of measurement for pressure
that is equivalent to one Newton per square
meter (N/m2
).
Pink Noise
A sound with a frequency spectrum that
is flat in logarithmic scale, and has equal
power in bands that are proportionally
wide.When compared with white noise, the
power density decreases by 3 dB per octave.
Pitch
Asubjectivesoundqualitythatisdetermined
by the frequency of a sound wave, or a
combination of waves, that is placed on a
scale extending from low to high.
Positive Air Flow
See Forward Air Flow.
Pressure Attenuation (Pa) Code
A code used to define the % of free area
of a silencer cross-section. A decrease in
free area typically results in an increased
insertion loss and increased pressure drop
across the silencer.
Pressure Drop
The difference in static pressure from the
inlet to the outlet of a system component.
Acoustics
The science that is related to the production,
control, transmission, reception, and effects
of sound.
Acoustic Media
The sound-absorbing material used inside
absorptive type silencers and plenum walls.
Ambient Noise
An all-encompassing noise that is present
in a given environment and is comprised
of many sounds from many sources, with
no particular sound being dominant. Also
known as background noise.
A-Weighting
A weighting network that is widely used,
often abbreviated dBA, dB(a). It has a
prescribed frequency response that bears
a close relationship to loudness judgments
of the human ear.
Background Noise
Noise sources other than the noise source
that is of interest or being measured. Also
known as ambient noise.
Breakout Noise
Noise that travels through the wall of an
enclosure or duct work into an occupied
space.
Broadband Noise
Noise with components over a wide range
of frequencies.
Decibel (dB)
A unit for expressing the ratio of two
amounts of acoustic signal power equal to
10 times the common logarithm (to the base
10) of this ratio.
Dynamic Insertion Loss
Theinsertionlossatagivenairflowdirection
and velocity. The insertion loss of a silencer
varies depending on whether the sound is
traveling in the same or opposite direction
as the air flow. Silencer performance
changes with the absolute duct velocity.
The unit of measurement is dB.
Flanking
Is when the walls of the ductwork on the
upstream side of a silencer are readily
excited into vibration, which is then
transmitted through the silencer walls and
internal components and re-enters the
downstream duct path as noise.
Forward Air Flow
A condition that exists when airborne
sound and air flow are moving in the same
direction. Also known as positive air flow
or supply air flow.
Free Field
The sound field where only directly radiated
sound waves moving away from the sound
source are present. This condition exists
when a sound source is located a large
distance from reflecting surfaces, or when
nearby surfaces are highly absorbent.
Frequency
The number of times in one second that
a passing wave repeats itself. The unit of
frequency is Hertz ( Hz), which corresponds
to 1 cycle per second.
Fundamental Frequency
The lowest frequency in a harmonic series.
Generated Noise
The sound power produced by air flowing
through a silencer at a given velocity and
direction (forward or reverse). The unit of
measurement is decibels (dB).
Harmonic
An integer multiple of the fundamental
frequency.
Hertz ( Hz)
The unit of measurement for frequency, or
the number or cycles per second.
HighTransmission Loss (HTL)
Occurs when a heavier material or
combination of materials create a higher
resistance to sound transmitting through
them.
Insertion Loss (IL)
The decrease in sound pressure level or
sound intensity level measured at a receiver
when the silencer or a sound-attenuating
element is inserted into the path between
the source and the receiver. The unit of
measurement is decibels (dB).
Intensity
See Sound Intensity.
Intensity Level
See Sound Intensity Level.
Media Protection
A liner that is applied between the fiberglass
media and the air stream of the silencer to
protect the media from erosion due to high
velocity air flow and airborne contaminates.
Module Factor
A value that is used to define the width of
a single module.
NC (Noise Criteria)
A weighted value obtained from a series
of curves that covers a spectrum of octave
bands with center frequencies ranging from
63 Hz to 8000 Hz. Sound levels are plotted
at each of these frequency bands, with the
highest point on the NC curve, regardless of
frequency, being the NC rating for the piece
of equipment.These values are commonly
used by manufactures to rate equipment
because this system factors in the human
sensitivity to each of the frequency bands.
The single number value is known as the
NC level.

M-3
© Copyright Price Industries Limited 2014. For more information on additional imperial and metric sizes,
Terminology
Noise Control
Engineering Guide
PureTone
Asinglefrequencysound.Asoundforwhich
the sound pressure is a simple sinusoidal
function of the time.
Random Noise
An oscillation whose instantaneous
magnitude is not specified for any given
instant of time.
RC (Room Criteria)
A value obtained from a series of curves
that cover a spectrum of octave bands with
center frequencies ranging from 16 Hz to
4000 Hz. This rating system was specifically
created to establish design goals for HVAC
systems, as it provides guidance for
maintaining a certain level of background
sound for masking.The curves are used to
provide a rating of an occupied indoor space
with a single number value indicated as the
RC level.
Return Air Flow
See Reverse Air Flow.
Reverberant Field
The sound field that consists of both directly
radiated and reflected sound waves.
Reverse Air Flow
A condition that exists when airborne sound
and air flow are moving in the opposite
direction. Also known as return air flow or
negative air flow.
Sabin
A unit of measurement for acoustic
absorption in relation to the absorption
by one square foot of a perfect absorptive
material.
SIL (Speech Interference Level)
The arithmetic average of sound levels
(dB) in the 500 Hz, 1000 Hz, 2000 Hz, and
4000 Hz octave bands. This rating deals
with the ability of speech to be heard and
understood.
Silencer Baffle
A silencer component that is comprised
of perforated metal and acoustic media or
resonant chambers.
Silencer Bank
A complete silencer assembly that
can contain one or multiple silencer
components.The bank dimensions are the
overall dimensions of the complete silencer,
and typically match the duct dimensions.
Silencer Component
A factory assembly that contains one or
morebafflesandmayormaynotbecoupled
with other components in the field to create
a larger silencer bank.
Silencer Module
A portion of the silencer that consists of
one air path located between two acoustic
baffles. A silencer can have multiple
modules within one component.
Sone
A subjective unit of measurement for
loudness for an average listener that is
equal to the loudness of a 1000 Hz sound
that has an intensity 40 dB above the
listener’s threshold of hearing.
Sound
(A) An oscillation in pressure, stress,
particle displacement, particle velocity, etc.
in an elastic or partially elastic medium,
or the superposition of such propagated
alterations.
(B) An auditory sensation evoked by the
oscillation described above.
Sound Intensity
Theamountanddirectionofflowofacoustic
energy at a given position (W/m2
).
Sound Intensity Level
Theratioofsoundintensity,whichisobtained
by taking ten times the common logarithm
of a given sound intensity in reference to
10-12
W/m2
. The unit of measurement is dB
re 10-12
W/m2
.
Sound Power
The total sound energy radiated by a source
per unit time. The unit of measurement is
the watt (W).
Sound Power Level
Algebraically defined as LW=10log(W/Wref)
where typically Wref = 10-12
watts. This
equation indicates that sound power level
is ten times the logarithm (to the base 10)
of the ratio of a given sound power to a
reference power (typically 10-12
watts). The
unit used to express sound power level is
decibels in respect to the reference sound
power (e.g. 84 dB re 10-12
watts).
Sound Pressure
The instantaneous difference between the
actual pressure produced by a sound wave
and the average or barometric pressure at
a given point in space.The unit of measure
is typically Pascals (Pa).
Sound Pressure Level (LP)
Algebraically defined as LP=20log(P/Pref)
where typically Pref = 20 x 10-6 Pascal.This
equation indicates that sound pressure level
is twenty times the logarithm (to the base
10) of the ratio of a given sound pressure
to a reference pressure (typically 20 x 10-6
Pascal). The unit used to express sound
pressure level is decibels in respect to the
reference sound pressure (e.g. 87 dB re 20
x 10-6
Pascal).
SoundTransmission Class (STC)
A single figure rating system designed to
give an estimate of the sound insulation
properties of floors, walls, ceilings,
windows, doors, etc.
Static Pressure (Ps)
Thepressureexertedequallyinalldirections
on a system, regardless of air flow.This can
also be defined as the difference between
Total Pressure (Pt) and theVelocity Pressure
(Pv), expressed as Ps = Pt-Pv.
Static Pressure Loss
The difference in static pressure from the
inlet to the discharge of a duct element.
Static Regain
An increase in system static pressure that
occurs in correlation with a decrease in
velocity pressure caused by an increase in
the cross-sectional area of the ductwork.
Supply Air Flow
See Forward Air Flow.
System Effect
Adeviationfromthecatalogedperformance
for a piece of equipment.This is caused by
the difference between how the product
was tested and how the product is actually
installed in the system.
Tone
An intense sound that is concentrated at
a single frequency and typically contains
harmonics at multiples (2x, 3x, 4x, etc.) of
the fundamental frequency.
Total Pressure (Pt)
The combined effect of velocity pressure
and the static pressure. This can also be
defined as the algebraic sum of Static
Pressure (Ps) and Velocity Pressure (Pv), Pt
= Ps + Pv.
Transmission Loss (TL)
A reduction of sound levels as a result of
passage through an obstruction such as a
wall, partition, or ductwork. These values
are expressed with a unit of decibels (dB).
Vibration
A periodic motion or displacement in a solid
elastic medium.
Velocity Pressure (Pv)
The pressure exerted by a moving fluid
which acts only in the direction of fluid flow.
This can also be defined as Pv = Pt - Ps.
Wavelength
The linear distance between two successive
points of a sound wave which are separated
by one period.
White Noise
A sound with a flat frequency spectrum in
linear scale. It has equal power in any linear
band and at any center frequency having a
given bandwidth.

Wavelength
Comparision of Wavelengths for Different Frequencies
Fundamental Concepts
What is Sound?
Sound is a propagating vibrational
disturbance or wave in an elastic medium
(solid, liquid or gas). Sound is most
commonly thought of as being transmitted
in air and detected by a person’s ears.
What is Noise?
Noise is defined as any unwanted or
undesirable sound. While sound in general
is not necessarily a problem and may even
be desired in certain situations, when it
is unwanted or annoying, we refer to it
as noise. The proper application of Noise
Control Products such as silencers and
panels are discussed in this engineering
guide.
Frequency
Frequency refers to the number of cycles
per second of an oscillation. For example,
middle C on a piano represents a pure tone
at 250 Hz.
The audible frequency range for humans
is about 20 Hz to 20000 Hz. This large
frequency range is broken down into
octave bands to make measurement and
analysis more manageable. Each octave
band is identified by the center frequency.
The eight commonly used octave bands for
HVAC noise are 63 Hz, 125 Hz, 250 Hz, 500
Hz, 1000 Hz, 2000 Hz, 4000 Hz, and 8000 Hz.
For more detailed analysis, octave bands
can be sub-divided into 1/3 octave bands.
Sound Pressure Levels
Sound is propagated as a pressure
fluctuation above and below the ambient
atmospheric pressure. The amplitude of
these fluctuations is proportional to how
loud something is perceived to be.
The range of pressure fluctuations that can
be detected by the human ear is extremely
large. The decibel (dB) scale is used to
describe sound pressure levels in acoustics
because it reduces the scale of values to
a more manageable range. Refer to the
Sound Pressure Level chart (right) to see
corresponding dB levels of common noises.
Decibel level is defined as:
Eq.1
where:
LP = Sound pressure level
p = Root mean square value of
acoustic pressure fluctuation,
Pa
pref = Reference quantity defined
as the threshold of hearing,
20uPa
Subjective and Objective Sound Changes
Subjective Change Objective Change
Much Louder More than 10 dB
Twice as Loud 10 dB
Louder 5 dB
Just Perceptibly Louder 3 dB
10 20 30 40 50 60 70
dB Level
80 90 100 110 120 1300
THRESHOLDOFHEARING
THRESHOLDOFPAIN
140
200 2,000 20,000 200,000 2,000,000 20,000,000 200,000,000
µPa Level
20
Forest
Library
Ofﬁce
HeavyTruck
JackHammer
JetTake-Off
Sound Pressure Levels
Noise Control
Engineering Guide

M-5
Heat Source Sound Source
Sound Power Levels
The sound power level of a source is a
measure of the acoustical energy emitted
by a source. Sound power is independent
of the environment and only depends on
the operating conditions of the equipment.
Equipment is rated in terms of sound power
levels to facilitate calculation of expected
sound levels due to the environment and
allowforfaircomparisonsbetweendifferent
sound sources. Sound power is defined as:
Eq.2
where:
LW = Sound power level
w = Acoustic energy radiated by source,
Watts
wref = Reference power defined as 10-12
Watts
Sound power levels cannot be measured
directly. Values are typically calculated
using sound pressure levels measured in a
laboratory environment with known sound
absorption characteristics.
There are several general techniques for
determining sound power levels which
cannot be measured directly. Sound power
levels are calculated from sound pressure
or intensity measurements in a controlled
environment.
A good analogy for the distinction between
sound power and sound pressure is an
electric room heater. The heater emits a
specific amount ofheatenergy, measured in
watts.The amount of heat energy produced
is a power rating that is independent of the
surroundings. However, the temperature
measured in the room will not only depend
onthepowerratingoftheheater,butalsoon
the distance from the heater, heat absorbed
by the walls, and heat transfer through the
walls, windows, etc. Similarly, a sound
source has a certain amount of sound
energy or power level.The sound pressure
measured in the room will be a function of
the sound power generated by the source,
as well as the distance from the source to
the measurement point and the amount of
sound energy absorbed and transferred by
the walls, windows, furnishings, etc.
Various HVAC Sound Sources
• Fans
• Rooftop Mounted Air Handling Units
• VAV Systems
• Air Flow Generated Noise
• Room Air Devices (GRDs)
• Compressors, Chillers, and Air-Cooled Condensers
• Emergency Generators
Noise Control
Engineering Guide
Fundamental Concepts

Source, Path, Receiver
A key approach to noise control is to
break each problem into its fundamental
components. This is the Source – Path
– Receiver concept. Every noise control
problem can be broken down into a source
creating the noise, a path transmitting the
noise, and a receiver hearing the noise.
There are different options available for
reducing the noise at each component.
The most desirable and effective option is
to treat the noise at the source. Selection
of quieter equipment can eliminate many
noise problems before they even begin.
Treatment options along the path are the
next best option and can include silencers,
barriers, absorption, lagging, or other
options.The last resort is typically treatment
at the receiver, with hearing protection for
loud occupational exposure.
Sound Sources
Wherever possible, it is important to
obtain source sound power levels from the
supplier.The sound power levels should be
derived from tested performance according
to a recognized standard applicable to that
equipment. Fans are commonly tested
per AMCA 300 or 320, Air Handling units
according to AHRI 260, terminal units
per ASHRAE 130. Testing according to a
recognizedstandardensuresthattheresults
can be compared and evaluated between
manufacturers. Estimates of power levels
should only be used as a last resort where
manufacturer supplied data is not available.
Common sound sources in an HVAC system
are fans, element generated flow noise,VAV
components, and mechanical equipment.
Path
Once the sources are known, the position in
relation to the receiver can be determined.
This will allow the path by which the noise is
transmitted to be identified. It is important
to note that noise typically travels through
multiple paths, both airborne and structural,
so possible paths must be acknowledged
and evaluated appropriately. Additionally,
once one path is treated, another path may
becomedominantandanyfurthertreatment
to the first path will not be effective.
The Sound Paths diagram (right) illustrates
possible transmission paths for the sound
and vibration from the source to the
receiver. In this example, the sound source
is an air handler that contains both a fan
and a compressor; the receiver is the human
occupant in the adjacent room.
Silencers are an effective and economical
means of incorporating noise control into
a system to reduce noise from duct-borne
paths.The main types of silencers, including
absorptive or dissipative, film lined, and
reactive or packless, are discussed in the
following sections.
Noise Control
Engineering Guide
Sound Paths
Path A – Structure-borne path, where the vibration of the air handler passes
through the floor.
Path B – Airborne path, where noise from the equipment radiates directly to the
receiver.
Path C – Duct-borne path, where noise from the equipment radiates through
the walls of the ductwork or passes through the supply/return ductwork into the
occupied space.
Receiver
After the source and path have been
identified, it is a matter of assessing the
receiver and determining what sound levels
are considered acceptable so that the most
effective and economical solution to the
noise problem can be selected. Calculation
of the sound pressure level at the receiver
is the final component to the source-
path-receiver concept, and combines
contributions from all path types. The
main consideration for specifying a target
or design sound criteria is the intended
Approach to Noise Control
use of the space. The most commonly
referenced source for typical design
criteria for an indoor occupied space is the
ASHRAE Applications Handbook. Outdoor
sound criteria are typically specified by local
ordinance in terms of overall A-weighted
value specified at a property line.

M-7
Noise Control
Engineering Guide
SilencerTypes and Applications
Absorptive Packless
Film Lined Absorptive
Absorptive
Acoustic silencers, which are also known as dissipative silencers,
utilize sound-absorbing media to attenuate sound levels. As the
noiseinsidetheductpassesthroughthesilencer,theacousticenergy
enters the baffles through the holes in the internal perforated metal
liner.This perforated metal liner protects the acoustic media from
being eroded by the air at high velocities, but has a large enough
free area to be acoustically transparent. Once inside the baffle, the
acoustic energy interacts with the absorptive media, which typically
consists of strands of glass fiber. The friction between the acoustic
energy and the glass fibers converts the acoustic energy into heat,
thereby reducing the amount of acoustic energy and decreasing
sound levels at the discharge of the silencer. For silencers that
will experience high gap velocities when installed, a sheet of
fiberglass cloth can be placed between the perforated metal and
the glass fiber media for protection against erosion with no effect
on the acoustic performance of the silencer. Typical absorptive
applications include rectangular, elbow, and circular ductwork, air
handling units, generator silencers, ventilation, fan plenums, and
general HVAC supply, return and exhaust.
Film Lined Absorptive
Film lined absorptive silencers work on the same principle as the
standard absorptive silencers. However, these silencers have a thin
polymer film liner wrapped around the acoustic media to protect
the media from airborne contaminants and moisture that may be
present in the air stream of some systems. It is important to note
that the addition of the film liner will negatively affect the sound
absorbing capabilities of the acoustic media. To minimize these
effects, a thin acoustic standoff liner is placed between the film and
the perforated metal.Typical film lined silencer applications include
laboratories, cleanrooms, and hospitals where contaminants and
moisture in the air stream may be of concern.
Packless
Packless silencers, sometimes referred to as reactive silencers,
contain no absorptive material and are constructed solely of solid
and perforated sheet metal. Attenuation of sound is achieved by
using multiple resonant chambers of varying size located behind
the perforated metal liner. As sound passes through the silencer,
the acoustic energy dissipates in a manner similar to the Helmholtz
resonator concept, which results in decreased sound levels at the
discharge of the silencer. Since these silencers are tuned to a
narrow band of frequencies, it is more difficult to achieve significant
attenuation over broadband frequencies. Packless silencers are
typically specified when glass fiber media is not acceptable or when
it is necessary to sterilize the entire duct system. This may include
laboratories, cleanrooms, hospitals, or electronics manufacturing.
Effect of Acoustic Media
The graph below is a comparison of the different silencer types.
The graph shows that the standard absorptive silencer has the
best overall performance across the full range of frequencies.The
addition of a film liner such as Mylar significantly decreases the
effectiveness of the absorptive silencer, but can be greatly improved
at the higher frequencies by placing an acoustic standoff between
the perforated metal and the film liner.The graph also shows the
unique performance characteristics of the packless silencer, which
utilizes tuned resonating chambers instead of acoustic media.The
standard absorptive silencer provides a fairly predictable broad
insertion loss curve across the frequency ranges, while the packless
silencer peaks in the mid frequency ranges.This peak is due to the
size and shape of the internal chambers that are tuned to remove
that frequency.
Comparison of 5 ft Long Silencer Performance

Rectangular
Rectangular silencers are the standard
for silencing noise transmitted through
ductwork. Their straightforward design
and relative low cost make them the first
choiceforthehighestsoundattenuationand
lowest pressure drop on the air distribution
system. They are available with a number
of options that allow them to be integrated
into any HVAC system with ease. A wide
range of designs with low to high pressure
drop and a large selection of media types
can be applied to systems ranging from
0-2500 fpm.
Elbow
Elbow silencers have many of the same
performance characteristics of rectangular
silencers, but are extremely versatile and an
excellent choice for systems where straight
lengths of ductwork are not available. Elbow
silencers perform at or above the levels of
rectangular silencers with a small increase
in pressure drop on the system, and can be
configured to suit most duct sizes without
the use of transitions.
Circular
Circular silencers are an excellent solution
when round ductwork is utilized in the
system.They eliminate the need for square-
to-round transitions that cause undesirable
pressure drops and system effects. Circular
silencers are available in a wide range of
sizes which allow for varying ranges of
attenuation and pressure drop.
Axial Fan
Axial fan silencers are designed to be close
coupled to an axial fan.These silencers are
engineered to provide noise attenuation
at the source and improve aerodynamic
performance at the inlet and discharge of
the fan.The axial fan silencer’s center pod
is properly sized to help reduce the pressure
loss over the fan hub. A discharge axial fan
silencer decelerates the air to maximize the
static pressure regain.
Custom
A standard silencer configuration cannot
always be adapted to work in every
situation. In these cases it is necessary to
develop a unique silencer that meets the
requirements of the application. When
noise control products must be applied
to a system with limited space or when
the silencer is directly coupled to a fan, a
custom silencer can be designed to provide
the required performance. Typical custom
designs include transitional silencers,T or Z
shaped silencers, and silencers that require
a size that is not available in the standard
model line.
Noise Control
Engineering Guide
Rectangular
Elbow
Circular
Axial Fan
Custom

M-9
Noise Control
Engineering Guide
AirTransfer Products
Air transfer silencers allow air to move from
one area to another without compromising
the acoustic integrity of the wall. These
silencers are typically not ducted and are
part of the wall construction.
Cross-Talk
Cross-talk silencers are used to transfer
air to adjacent areas while providing
the necessary attenuation to prevent
transferring unwanted noise. They are
commonly used to prevent speech intrusion
into adjacent rooms. Cross-talk silencers are
manufactured in a variety of configurations
that can be used to solve many different
acoustic air transfer problems.
Thin Line Return Dissipater
Thin line return dissipaters utilize multiple
baffles filled with acoustic media that are
staggered in a frame that is only 4 in. thick.
They are great for applications in place of
standard transfer grilles to reduce sound
transmission between adjacent spaces or
to attenuate return air noise.
Acoustic Louvers
Acousticlouverscanbeusedforallowingair
to flow through an opening while providing
the necessary sound attenuation. Acoustic
louvers use acoustic media to absorb the
sound energy and a perforated metal to
protect the media from erosion by the air
flow. Acoustic louvers are designed to be
aerodynamic to help minimize the pressure
drop.
Acoustic Panels and Enclosures
Used for controlling excessive noise from
equipment, Price acoustic panels and
enclosures are available in many shapes
and sizes to meet specific noise reduction
requirements.Typical applications include
barrier systems, custom enclosures,
and inlet and exhaust plenums; with
applicationsranging from largeunitsfor gas
turbines to smaller units for pumps, motors,
compressors or any other unwanted HVAC
or industrial noise source.
Cross-Talk
Thin Line Return Dissipater
Acoustic Louvers
Acoustic Panels
and Enclosures

Noise Control
Engineering Guide
Casing
The outer shell of the silencer is constructed
of solid sheet metal. This shell can be
fabricated from various materials and range
in thickness from 24 gauge to 10 gauge.
A heavier gauge casing is often used to
improve the transmission loss properties
of the silencer, which reduces the amount
of noise that can breakout through the walls
of the silencer and enter into the occupied
space. A heavier gauge material will also
make the silencer more robust to provide
resistance to the elements or other sources.
Standard silencer casings aremanufactured
from hot-dipped galvanized steel with a
coating weight of G-90 (G-90 designates
a zinc coating of .90 oz/ft2
). Additional
available casing materials are 304 and 316
stainless steel and aluminum.
Perforated Liner
The perforated material on the interior of
the silencer is specially designed to provide
protection to the internal acoustic media,
but is acoustically transparent, allowing
sound energy to penetrate the acoustic
media.
Acoustic Media
In absorptive silencers the acoustic media
is the internal fibrous material that absorbs
energy from the sound waves as they pass
through the silencer. The selection of this
material may be based on requirements
including local and international standards,
the application parameters, and the
customer’s preference.
Liner
Various silencer liner materials can be
installed depending on the application.
Liners like fiberglass cloth are used to
protect the internal acoustic media from
erosion in applications with high velocity
air flow. Polymer film liners such as Mylar
or Tedlar can be used to protect against
moisture or other contaminants that may
be found in the air. It should be noted that
a fiberglass cloth liner will not affect the
acoustic performance of the media, while
liners such as Mylar will cause decreased
insertion loss levels.
Acoustic Standoff
Acoustic standoff is required in silencers
with film liners in order to improve the
performance of the unit. By providing a gap
between the perforated liner and the film
liner, the acoustic standoff greatly increases
the absorptive characteristics of film lined
silencers.
Construction Standards
All components used in the construction
of Price acoustical products conform to
ASTM E84, UL723, and NFPA255 for a flame
spread classification of 25 and a smoke
development rating of 50.
Silencer Construction
Casing
Perforated Liner
Acoustic
Media
Acoustic
Standoff
Liner

M-11
Silencer Dimensional Considerations
The dimensions of a silencer depend on the
availablespace,performancerequirements,
and dimensions of the ductwork upstream
and downstream of the silencer.
Silencer width and height dimensions are
typically specified to match the ductwork.
The main benefits of matching the silencer
dimensions to the ductwork are the
elimination of costly transitions and the
effect of the transitions on the silencer
performance. Transitions at the inlet and
dischargeofthesilencerwillcreateturbulent
air flow that may cause the pressure drop
and generated noise to increase.
The length of the silencer is typically
determined by performance requirements
and the space available. A longer silencer
will provide greater insertion loss, but this
must be weighed against the increased
pressure drop and additional cost.The most
cost effective solution is to build silencers
only to the length necessary to meet the
insertion loss requirements.
Due to construction constraints and
performance requirements, it is necessary
to have multiple silencer configurations
available. Rectangular and elbow silencers
consist of three variables that represent the
configuration of the silencer. These three
variables are the module, component, and
bank dimensions.
Silencer Module
A silencer module consists of two half
baffles and one air gap, and can vary in
width.The module width dimension, baffle
geometry, and length of the silencer will all
depend on a combination of performance
requirements, available space, and duct
dimensions.
Silencer Component
Due to raw material size and shipping
constraints, large silencers need to be
manufactured in several pieces, called
components. A component may consist of
one or more modules, depending on the
performance required. These components
are assembled on-site to make up the
silencer bank.
Silencer Bank
Thesilencerbankdimensionsaretheoverall
dimensions of the silencer, and are typically
equal to the duct width and height in which
the silencer is installed. The silencer bank
may consist of one or multiple components,
which are made up of one or multiple
modules.
Varying silencer models may have different
dimensional constraints, therefore the
individual data sheets or silencer selection
program should be referenced for available
dimensions.
Air Flow Pattern when Silencer Matches Ductwork
Noise Control
Engineering Guide
Multiple Module, Single Component Silencer
Multiple Module, Multiple Component Silencer
Effects ofTransitions on Air Flow

Un-Nested Elbow
When the component width is equal to the
bank width, the elbow silencer will be an
un-nested configuration. For this elbow
configuration, the performance center
line length is equal to the bank center line
length.The model number will always show
the performance center line length as the
model number represents how the silencer
will perform.
Nested Elbow
The elbow silencer configuration will be
nested when the bank width is made up of
multiple components which are identical
in size and performance. Duct extensions
are used to make an even duct connection
for the silencer inlets and outlets. When a
silencer is nested, the performance center
line will be different from the bank center
line. The performance center line is the
center line of each individual component,
while the bank center line is the geometric
center line of the entire elbow assembly.
Un-Nested Elbow Configuration
Bank (Geometric) Center Line = Performance Center Line = Leg A + Leg B –
Bank Width (or Component Width)
Nested Elbow Configuration
Bank (Geometric) Center Line = Leg A + Leg B – Bank Width
Performance Center Line = Bank Center Line – Component Width
Noise Control
Engineering Guide
Silencer Dimensional Considerations

M-13
Testing Noise Control Products
Noise Control
Engineering Guide
Test standards are published procedures
and requirements for performing a specific
measurement or procedure. These are
consensus based documents developed
and typically written by a committee
formed by people who are familiar with
and interested in the specific measurement
procedure. These documents are typically
administered by independent, not-for-
profit groups such as ASTM International,
ASHRAE,ANSI, SAE, ISO, and others. Many
of these groups are open to any interested
party who would like to participate in the
standards development process.
Lab Accreditation
The National Voluntary Laboratory
Accreditation Program (NVLAP*) is
administrated by the National Institute
of Standards and Technology (NIST).
This organization provides third-party
accreditation to public and private
laboratories based on evaluation of their
technical qualifications and competence
to carry out specific calibrations or tests.
Accreditation criteria are established in
accordance with the U.S. Code of Federal
Regulations(CFR,Title15,Part285)andNVLAP
Procedures and General Requirements, and
encompass the requirements of ISO/IEC
17025. NVLAP accreditation signifies that a
laboratoryhasdemonstratedthatitoperates
inaccordancewithNVLAPmanagementand
technical requirements pertaining to quality
systems, personnel, accommodation and
environment; test and calibration methods;
equipment; measurement traceability;
sampling; handling of test and calibration
items; and test and calibration reports.
NVLAP accreditation does not imply any
guarantee or certification of laboratory
performance or test/calibration data; it is
solely a finding of laboratory competence.
A laboratory may cite its accredited status
and use the NVLAP term and symbol on
reports, stationery, and in business and
trade publications provided that this use
does not imply product certification. This
means that when a laboratory is accredited
for ASTM E477 (or any other test standard),
the laboratory is capable of testing to this
standard, but the data produced by the
laboratory is neither certified by NVLAP
nor is the data itself verified in any way.
The Price Sound Lab is NVLAP accredited
for acoustical product testing according
to current versions of ANSI S12.51
Determination of Sound Power Levels of
Noise Sources Using Sound Pressure -
Precision Method for Reverberation Rooms
and ASTM E477 Measuring Acoustical and
AirFlowPerformanceofDuctLinerMaterials
and Prefabricated Silencers.
* All information pertaining to these
organizations has been reviewed and
approved by each of the respective
organizations.
Product Certification
Performance data certification has been
widely adopted within the HVAC industry.
The distinction between data certification
and lab certification is the scope of what is
being compared. A lab certification looks at
the internal processes and documentation
for the lab. Product certification involves
independent third-party verification of
manufacturer performance data. Sample
products are often randomly selected and
testedtoverifythatcatalogdataispublished
in accordance with independent third-party
results. Air-Conditioning, Heating, and
Refrigeration Institute (AHRI) administers
theheating,ventilation,airconditioningand
commercialrefrigeration(HVACR)industry’s
performance certification programs for
heating and cooling equipment and
components. Manufacturers who have
had their product performance claims
tested and certified by AHRI can apply one
of the association’s family of certification
marks. The Air Movement and Control
Association (AMCA) International, Inc. is a
not-for-profitinternationalassociationofthe
world’s manufacturers of related air system
equipment - primarily, but not limited to:
fans, louvers, dampers, air curtains, air flow
measurementstations,acousticattenuators,
and other air system components for the
industrial, commercial and residential
markets. AMCA International has been
serving the industry and the public since
1917, and is considered the world’s leading
authority in the development of the science
and art of engineering as it relates to air
movement and air control devices. AMCA
International publishes and distributes
standards, references, and application
manuals for designers, engineers, and
others with an interest in selection,
evaluation, and troubleshooting of air
system components. AMCA International
has developed a certified rating program
(CRP) for prefabricated acoustical duct
silencers which looks at dynamic insertion
losses, air flow generated noise, and
pressure drop as a function of air flows
obtained in accordance with ASTM E477-
13.TheAMCA publication 1011-03 details the
test method and procedure for licensing a
product to carry the AMCA seal.

1
2
3
AirTransfer SilencerTest Method
Thereiscurrentlynotestmethodestablished
for air transfer silencers. The performance
data for these products is typically reported
as noise reduction or transmission loss.
These silencers are installed as part of a
larger assembly, with the percentage of the
transfer opening determining the effect on
the overall transmission loss of the installed
wall.
Acoustic louvers are typically tested and
rated by AMCA according to AMCA 500L
for air leakage, pressure drop, and water
penetration. Acoustical louvers are typically
tested according to ASTM E90 for sound
transmission loss.The performance is often
reported as a noise reduction to account
for the louver being installed in a free field
environment versus a reverberant test
environment.
SilencerTest Method
Duct silencer performance data is
obtained according to the procedures
and requirements specified by the latest
version of ASTM E477. A silencer (1) is
installed in a straight length of ductwork
that joins a single source chamber (2) and
a reverberation room (3). The ductwork
upstream of the silencer entrance must be a
straightrunwithnotransitionsorelbowsfor
a minimum of 5 equivalent duct diameters,
and downstream of the silencer discharge
no less than 10 equivalent duct diameters.
The single source chamber (2) consists of
a heavy gauge enclosure that is lined with
sound-absorbing material that exceeds 0.25
NRC. Inside this enclosure are multiple loud
speakers that are electronically coupled to
ensure all speakers are acting in phase.The
speakers are structurally isolated from the
chamber and duct system to minimize the
chance of sound entering the reverberation
room by paths other than through the
ductwork. These speakers produce a pink
noise that has a series of 1
/3 octave bands
with center frequencies ranging from 50 to
10 000 Hz. The test signal in each band is
maintained within ± ½ dB throughout the
test, and is monitored electronically by
measuring the voltage at the loud speaker
voice coil.
With the silencer and ductwork in place,
measurementsaretakeninthereverberation
room(3)usingarotatingboommicrophone,
filtering equipment and a sound analyzer
thatmeettherequirementsoutlinedinASTM
test method E90.The insertion loss values
areobtainedbytakingsoundmeasurements
with the silencer installed in the duct and
then again with an unlined piece of duct of
like construction in place of the silencer.The
difference between the two measurements
is the insertion loss of the tested silencer.
The measurements are taken several times
at various air flow rates, including no flow,
and since the performance of the silencer
will change based on air flow direction, the
test is also run under conditions of forward
and reverse flow.
To obtain generated noise data, the same
setup is used, with the exception of the
single source sound chamber, which is
turned off.The sound level measurements
are taken with an empty piece of duct to
establish the system noise, including fans,
ductwork, and laboratory surroundings,
then measured again with the silencer in
place. The generated noise performance
of the silencer is the difference between
the two measurements with a correction
factor that accounts for the effects of end
reflection.
Noise Control
Engineering Guide
Acoustic PanelTest Method
Acoustic panels are tested for transmission
loss and absorption. Transmission loss is
tested according to ASTM E90 Standard
Test Method for Laboratory Measurement
of Airborne Sound Transmission Loss of
Building Partitions and Elements.ASTM E90
is a laboratory measurement of airborne
sound transmission loss of building
partitions. The test specimen is installed
between two adjacent reverberation rooms,
with the rooms being isolated such that
the only significant sound transmission
path is the test specimen. A sound source
creates a diffuse sound field in the source
room, and the resulting sound pressures
in the source and receiving rooms are
measured. The transmission loss of the
specimen is calculated using the measured
sound pressure levels, the receiving room
absorption, and the specimen area. The
acoustic absorption of panels is measured
using ASTM C423. Acoustic absorption is
a measure of the sound energy reflected
by a surface. Small absorption coefficients
mean that most of the acoustic energy is
reflected into space. A perfect absorber,
where all acoustic energy is dissipated, has
a coefficient of 1.
SilencerTest Setup per ASTM E477

M-15
Relevance ofTest Standard Version
The 1999 version of ASTM E477 introduced
significant changes to the calculation of
insertion loss. Versions of the test standard
upto1996calculatedinsertionlossbasedon
the difference between octave band sound
pressure levels for the empty and silenced
duct. Insertion loss calculated according
1996 and earlier versions assume a flat
sound spectrum generated by the sound
source. If the sound spectrum is not flat, the
insertion loss can be biased to the highest
1/3rd octave band value. Results from the
old test standard could provide a higher
insertion loss value for an individual octave
band than would be realized in practice.
Current versions of the test standard (1999
and on) calculate the octave band insertion
loss based on the logarithmic average of
the 1/3rd octave performance.This method
of calculation is unaffected by the frequency
spectrum of the sound source and provides
a realistic number for the entire octave
band. The other significant change was
defining how to test elbow silencers. Prior
to 1999, the test method for elbow silencers
was left to the discretion of the individual
manufacturer. Comparisons of silencer
performance data and acoustic calculations
should always be performed with data
tested according to the most current version
of the test standard.
Price Sound Lab
For over 30 years, Price has been generating
accurate, reliable performance data for
grilles, registers, diffusers, and terminal
unitsusinganextensivein-housetestfacility.
Ourlaboratorywasexpandedandupgraded
in 2007 to include the new Price Sound Lab
for testing and development of the Price
noise control product lines. By furthering
the capabilities of the Price Laboratories to
include noise control products, this world-
class research and development facility with
state-of-the-art test equipment solidifies
our commitment to noise control product
innovation and performance.
In the Price Air Distribution Laboratories,
6,500 ft2
of space has been dedicated to
the testing and development of the Price
Sound Lab. The Price Sound Lab includes
a 21,000 ft³ reverberant Sound Chamber
designed specifically for testing commercial
and industrial noise control products in
accordance with ASTM and ANSI test
standards, down to 50 Hz.
Air flow to the reverberant sound chamber
is supplied by a dedicated bi-directional,
variable speed axial fan.This fan system is
capable of producing up to 30,000 cfm at
4 in. w.g. in both directions, which allows
for testing of supply and return applications.
Utilizing a networked graphical data
acquisition system and NIST traceable
flow meters, the test parameters and
conditions are monitored with the highest
level of precision, while Bruel and Kjaer
Multi-ChannelAnalyzers ensure the highest
accuracy of sound measurement available.
The entire noise control test facility was
designed and constructed utilizing the
latest AMCA test standards. This industry-
leading facility also gives Price the ability to
perform in-house testing on a wide array of
custom products to the appropriate testing
standard.
Noise Control
Engineering Guide
Price Sound Laboratory
IndependentTesting
At Price we believe that third-party
verification of certified test data is an
excellent way to verify that the published
catalog data and finished products are
designed and performing correctly.That is
why throughout our product development
and catalog testing, we sought and will
continue to seek independent testing for
our noise control product line.Through this
third-party testing we are able to verify that
our laboratory is conducting measurements
accurately.
Insertion Loss

Performance
When selecting silencers or noise control
products for an HVAC system, the following
performance parameters need to be
considered.
Air Flow Direction & Velocity
The direction and face velocity of the air
flow through the duct will directly affect the
performance of a silencer. Both of these
parameters must be known to properly
determine the performance of a silencer.
Theforemostparameterinsilencerselection
is the insertion loss. Insertion loss is the
decrease in sound pressure levels that can
be expected when a silencer is inserted
into the path between the source and the
receiver.The data is provided at each of the
octave band center frequencies typically
rangingfrom63Hzto8000 Hzandat varying
duct velocities in forward and reverse flow.
Pressure Drop
The pressure drop is the differential static
pressure of the silencer. The upstream
location is a minimum of 5 equivalent
diameters upstream and the downstream
location is a minimum of 10 diameters from
thesilencer. Whenaddinganycomponentto
an HVAC system, the pressure drop should
always be considered. With a commercial
silencer, pressure drop typically ranges
from 0.01 in. w.g. (3 Pa) up to 1.00 in. w.g.
(249 Pa). A poor silencer selection resulting
in a high pressure drop can make the entire
system operate inefficiently or ineffectively.
It is desirable to keep the pressure drop of
a silencer below 0.35 in. w.g. (87 Pa), but
this is not always possible when trying to
achieve high insertion loss values.
Generated Noise
Generated noise is the sound power created
when air flows through a silencer at a given
velocity and direction (forward or reverse).
Since these values represent the amount
of sound produced by the silencer, a lower
value will indicate better performance. Data
for generated noise levels are provided at
each of the octave band center frequencies
ranging from 63 Hz to 8000 Hz.This data is
based on a standard cross-sectional area,
and when this area increases or decreases,
a correction factor that is logarithmically
proportional to the cross-sectional area
must be applied to the data. It is important to
note that generated noise in a given octave
band does not contribute to the overall
sound level if the value is 10 dB below the
attenuated sound levels exiting the silencer.
When the generated noise values are within
10 dB of the attenuated levels, generated
noise values are logarithmically added to
attenuated levels to predict the final sound
level.
Performance
Generated Noise
Pressure Drop
Generated Noise Corrections (Based on a 4 ft2
silencer)

Noise Control
Engineering Guide
Face Velocity
fpm (m/s)
Dynamic Insertion Loss (dB) Measured at Octave Band Center Frequencies
63 Hz 125 Hz 250 Hz 500 Hz 1000 Hz 2000 Hz 4000 Hz 8000 Hz
+1000 (+5.08) 6 10 23 36 38 28 16 14
+500 (+2.54) 7 10 24 37 39 29 16 14
0 (0.00) 7 11 26 38 40 30 16 14
-500 (-2.54) 7 12 28 39 41 31 16 14
-1000 (-5.08) 8 12 29 40 42 32 16 14
Length in. (mm)
Pressure Drop (in. w.g. [Pa]) at a Specific Face Velocity
500 fpm 1000 fpm 1500 fpm
36 (914) 0.16 (40) 0.61 (152) 1.4 (348)
60 (1524) 0.16 (40) 0.66 (164) 1.48 (368)
84 (2134) 0.18 (45) 0.7 (174) 1.57 (391)
108 (2744) 0.17 (42) 0.7 (174) 1.57 (391)
Face Velocity
fpm (m/s)
Generated Noise (dB) Measured at Octave Band Center Frequencies
63 Hz 125 Hz 250 Hz 500 Hz 1000 Hz 2000 Hz 4000 Hz 8000 Hz
+1000 (+5.08) 63 56 51 46 46 51 49 42
+500 (+2.54) 61 50 37 32 33 31 28 31
-500 (-2.54) 63 52 42 45 46 43 33 29
-1000 (-5.08) 63 53 47 48 53 59 57 47
Silencer Face Area (ft2
) 0.5 1 2 4 8 16 32 64 128
dB Addition or Reduction -9 -6 -3 0 +3 +6 +9 +12 +15

M-17
Factors Affecting Performance
Noise Control
Engineering Guide
Effect of Flow on SilencerAttenuation
Thedirectionandvelocityofairflowthrough
a silencer in reference to the direction
sound is traveling will have an affect on the
insertion loss performance that a silencer
will provide. When insertion loss values
include the effects of air flow direction and
velocity it is known as dynamic insertion
loss.
The terms forward flow or positive (+) flow
indicate that the air is flowing through the
silencer in the same direction the sound
is traveling. These conditions occur in a
supply air system or on the outlet of a fan.
The terms reverse flow or negative (-) flow
indicate that the air is flowing through
the silencer in the opposite direction of
the noise. Examples of these conditions
include a return air system or an exhaust
application.
In reverse flow conditions, when the
air flows in the opposite direction of the
sound wave the effective speed of sound
decreasesslightly,causingthesoundtotake
a longer period of time to travel the silencer
passages. This results in improved low
frequency insertion loss performance. At
high frequencies, however, the attenuation
decreases as the velocity profile in the
silencer passage tends to focus the sound
toward the center of the passage and away
from the acoustic media.
The opposite is true of forward flow
applications. When the air is flowing in the
direction of sound propagation the result
is decreased acoustic performance at low
frequencies and increased performance at
high frequencies.
The direction of air flow and air flow velocity
can be important factors in making the best
decision for the selection of a silencer. For
critical noise control applications, selection
software like Price All-In-One, which allows
the exact air velocity to be entered and
corrects the insertion loss values for the
direction of flow, should always be used.
Forward Flow
Reverse Flow
Standard Ductwork
Exhaust Applications
Inside Air Handler

Noise Control
Engineering Guide
1. Straight Unobstructed Duct 2. Free Air/Plenum with Smooth Inlet
The desired installation for a silencer will
have 3 to 4 duct diameters of straight
ductwork upstream of the silencer.
This type of installation will result in
performance that is very similar to
cataloged data.
When a silencer is installed 3 to 4 duct
diameters downstream of a free air
intake/plenum with smooth inlet, a
pressure drop factor of 1.05 should
be applied. This type of installation will
result in a slight deviation from cataloged
performance data.
3. Free Air/Plenum with Sharp Inlet
diameters downstream of a free air
intake/plenum with a sharp inlet, a
pressure drop factor of 1.1 to 1.3 should
be applied. This type of installation will
result in a moderate deviation from
cataloged performance data.
5. Radius Elbow with No Turning
Vanes
diameters downstream of a radius elbow
with turning vanes, a pressure drop
factor of 1.05 should be applied.This will
result in a slight deviation from cataloged
performance data.
diameters downstream of a radius elbow
without turning vanes, a larger pressure
drop factor of 1.1 should be applied.This
will result in a moderate deviation from
diameters downstream of a mitered
elbow, an even larger pressure drop
factor of 1.3 should be applied.This type
of installation will result in a moderate
deviation from cataloged performance
data.
4. Radius Elbow withTurning Vanes 6. Miter Elbow
diameters downstream of a fan, a
pressure drop factor of 1.3 should be
applied. This type of installation will
7. Fan Discharge
Installed Pressure Drop, System Effect
Elements in a duct system, such as elbows, tees, and transitions, can have a negative effect on the performance of a silencer if they are
located too close to the silencer inlet or discharge.The effect of these elements on a silencer is known as “system effect.”The effect that
an element will have on performance depends on the type of element and its distance to the inlet or outlet of the silencer.The ASTM
Standard E-477, to which silencers are tested, states that there shall be straight duct of no less than 5 duct diameters upstream of the
silencer and no less than 10 duct diameters downstream of the silencer. In actual applications these conditions are often not possible;
however, a minimum of 3 to 4 duct diameters on both sides of the silencer should be a design goal.The ASHRAE Applications Handbook
provides correction factors that can be applied to the pressure drop of a silencer for various duct elements at a distance within 3 to
4 duct diameters of the silencer inlet or outlet. The ASHRAE Handbook recommends the pressure drop across a silencer not exceed
0.35 in. w.g., with the correction factors applied to ensure that a silencer performs as intended.
Equivalent Duct Diameter = Square Root [(4 x Duct Width x Duct Height) / π]
Silencer Inlet Conditions
Below are common inlet conditions that a silencer may be installed downstream of, along with their corresponding correction factors.
When a silencer is installed within 3 to 4 equivalent duct diameters of one of these seven elements, the actual pressure drop will
increase from the cataloged silencer performance.To obtain the installed pressure drop, multiply the cataloged pressure drop by the
corresponding system effect correction factor.

M-19
Silencer Outlet Conditions
Below are common outlet conditions that a silencer may be installed upstream of, along with their corresponding corrections factors.
When a silencer is installed within 3 to 4 equivalent duct diameters of one of these seven elements, the actual pressure drop will
increase from the cataloged silencer performance.To obtain the installed pressure drop, multiply the cataloged pressure drop by the
corresponding system effect correction factor.
Example
Determine the actual pressure drop for a rectangular silencer installed with a mitered elbow 4 duct diameters upstream and an abrupt
doubling of the duct area 2 duct diameters downstream. From the catalog or software selection program, a rectangular silencer model
shows a pressure drop of 0.21 in. w.g. at 2000 fpm. To determine the installed pressure drop of the silencer including the system effect,
multiply the pressure drop by the corresponding correction factors.
Installed Pressure Drop = Cataloged Pressure Drop x Inlet Pressure Drop Factor x Outlet Pressure Drop Factor
Pressure drop of the rectangular Silencer = 0.21 in. w.g.
Inlet correction factor for a miter elbow = 1.3
Outlet correction factor for an abrupt doubling of duct area = 1.4
Therefore:
Installed pressure drop = 0.21 x 1.3 x 1.4 = 0.38 in. w.g.
Noise Control
Engineering Guide
8. Straight Unobstructed Duct 9. Duct Doubles Area Abruptly
The desired installation for a silencer will
have 3 to 4 duct diameters of straight
ductwork downstream of the silencer.
This type of installation will result in
performance that is very similar to
cataloged data.
diameters upstream of a duct transition
that abruptly doubles the cross sectional
area of the duct work, a pressure drop
factor of 1.4 should be applied.This type
of installation will cause a large deviation
from cataloged performance data.
10. Abrupt Expansion/Plenum
When a silencer is installed 3 to 4
duct diameters upstream of an abrupt
expansion/plenum, a pressure drop
factor of 2.0 should be applied. This
type of installation will result in a large
deviation from cataloged performance
data.
12. Radius Elbow with NoTurning
Vanes
diameters upstream of a radius elbow
with turning vanes, a pressure drop
factor of 1.5 should be applied.This will
result in a large deviation from cataloged
performance data.
diameters upstream of a radius elbow
without turning vanes, a larger pressure
drop factor of 1.9 should be applied.
This will result in a large deviation from
diameters upstream of a mitered elbow,
an even larger pressure drop factor of
2.0 should be applied. This will result
in a large deviation from cataloged
performance data.
11. Radius Elbow withTurning Vanes 13. Miter Elbow
diameters upstream of a fan, a pressure
drop factor of 1.2 to 1.4 should be
applied. This type of installation will
14. Fan Inlet

Noise Control
Engineering Guide
1. Inlet/Discharge of Air Handler
3. DuctTerminations
5. Close Coupled to Fan
2. Riser Branches
Location in System
Silencer Location
Silencers are an important part of an HVAC
system. If the silencer is installed in a poor
location the desired results will not be
achieved. Listed below are some typical
silencer locations that are used in HVAC
systems.Thechoiceoflocationisdetermined
by the type of equipment being used, the
locationofthemechanicalroomwithrespect
to the occupied spaces, and the required
noise levels in the occupied spaces.
1. Inlet/Discharge of Air Handler
Silencers placed at the inlet and/or discharge
of air handling equipment are typically
used to attenuate noise right at the source,
reducing or eliminating the need for further
sound attenuation downstream.Attenuating
the noise at the source can also help to
eliminate both airborne and structure borne
noise from propagating through the rest of
the building.
2. Riser Branches
It is often not practical to install silencers
at the source of the noise, which creates
the need to attenuate the noise further
downstream. When silencers are placed in
riser branches, the noise concern can still be
dealt with before the noise moves into the
occupied space of each respective floor in
the building.
3. DuctTerminations
Sometimes noise control products are
required closer to the occupied space.
This can be due to space constraints or to
attenuatednoisegeneratedbyductelements
far from the mechanical room, such as
dampers,terminalunits,fanpoweredboxes,
control valves, or exhaust fans.
4. Speech / Equipment Noise
Duct silencers may also be used in
applications where they are not part of a
typical supply or return air ducting system.
Instead, the silencers are used to reduce
sound transfer in ductwork that is dealing
with pressure differentials between two
spaces. It is often necessary to eliminate
speech transfer between adjacent offices or
meeting rooms, or to prevent the noise of a
manufacturing plant from entering adjacent
office spaces.
5. Close Coupled to Fan
In some cases there will be a need to silence
fan noise directly before or after an axial fan.
In these instances, it is important to create a
silencer design that corresponds directly to
the fan itself, rather than utilizing a silencer
that is “off the shelf.”These custom silencer
designs not only greatly reduce fan noise,
but can also improve the performance of the
fan by providing static regain at the outlet of
thedischargesilencer.Thereareseveralother
typesoffaninletanddischargesilencersthat
can be used with centrifugal fans as well.
4. Speech / Equipment Noise

M-21
Location in System
Noise Control
Engineering Guide
Breakout Noise
Sound that is allowed to pass through the
wallsoftheductworkandthesilencercasing
is called breakout noise. Many things will
contribute to the amount of sound that is
able to break out of the silencer casing,
including the shape and size of the silencer,
the gauge of material used to construct the
casing, and the amount of acoustic media
in the walls.The transmission loss table to
the right shows the transmission loss values
of different rectangular silencer casing
construction classes. The HTL2 casing has
the highest transmission loss performance,
therefore less noise will break out of the
casing of a HTL2 silencer as compared to
a CL1 silencer.
When trying to limit breakout noise in an
HVAC system the silencer should be located
as close as possible to the noise source.
This will allow the silencer to attenuate
the sound before it has a chance to travel
through the duct system to an area where
noise breakout through the duct walls will
be a concern.
Mechanical Room
When removing airborne sound created
by fans and other equipment located in a
mechanical room, the ideal location for the
silencer is straddling the mechanical room
wall. This location removes the unwanted
sound created by the equipment as it leaves
the mechanical room, which eliminates the
concerns of breakout noise in occupied
spaces. However, fire dampers are typically
located at the wall of the mechanical room.
When this is the case, the best location for
the silencer is inside the mechanical room,
just before the mechanical room wall. If
adequate space inside the mechanical room
is not available, the silencer may need to be
located outside the room. In this situation
the silencer should again be located at the
mechanical room wall, but a heavier gauge
material may be required to prevent noise
from breaking out of the silencer before it
is fully attenuated.
Transmission Loss
Construction Transmission Loss (Rectangular Silencers)
Class Gauge 63 Hz 125 Hz 250 Hz 500 Hz 1K Hz 2K Hz 4K Hz 8K Hz
CL1 22 25 26 28 30 33 37 40 40
CL2 18 27 28 30 32 35 38 41 41
HTL1 16 28 29 31 33 36 39 42 42
HTL2 10 31 33 34 36 38 42 45 45

Silencers panels-engineering-guide

More Related Content

What's hot (20)

Similar to Silencers panels-engineering-guide (20)

Recently uploaded (20)

Silencers panels-engineering-guide